P44TG_4:1

P44TG-xxxxE/Z4:1MLF
PMV-SERIES
Rev.02-2009
12 Watt, 4:1 Ultra Wide Input
DIP24 Metal Case
1.5 kV DC I/O Isolation
Single and Dual Reg. Output
Continuous Short Circuit Prot.
Over Voltage/Load Protection
Soft Start, Remote Ctrl.
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
The PMV 12W series P44TG-xxxxE/Z4:1MLF is a family of cost effective
12W single & dual output DC-DC converters. These converters are
encapsulated in miniature DIP24 metal case. High performance features:
Synchronous rectification, 1500VDC input/output isolation, continuous short
circuit protection with automatic restart and tight line / load regulation, high
efficiency operation, output voltage accuracy of ±1.2% maximum and a
wide input range of 4:1
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current
Start-up Time
4:1 Wide Input
Pi Type
20 mA pk-pk
20mS, typ
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (0% – 100%)
Cross Regulation1 (Dual Output)
Ripple and Noise3 (20Mhz bandwidth)
Over Load Protection
Temperature Coefficient
Transient Recovery Time4
Transient Response Deviation4
± 1.2%
Indefinite (hiccup, Automatic Recovery)
± 0.2%
± 0.5% (Single Out) ± 1.0% (Dual Out)
± 5%
85 mV pk-pk
170% of FL, typ.
± 0.02% / °C
250us, typ.
± 3%, max.
General Specifications
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacitance
I/O Isolation Resistance
Switching Frequency (typical)
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
1500 VDC
1500 pF, typ.
1000 MOhm
270 kHz
95% rel H
> 1 Mhrs
Physical Specifications
Case Material
Potting Material
Weight
Nickel Coated Copper
Epoxy (UL94V-0 rated)
~ 18g, typ.
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +60°C (ambient, for 100% load)
105°C
-40 to +125°C
Free Air Convection (10 mm distance required)
Soldering 260°C, max. (1.5 mm from case 10s.)
PMV-Series – P44TG-xxxxE/Z4:1MLF – Single and Dual Output – DIP24 - Metal Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/4
Selection Guide
Single/Dual Output
Order #
)
)
)
mA
(mA
A)
mA
d
m
(
(
a
ad (
d
o
)
o
d
a
L
L
a
C
)
o
.
l
o
L
D
F)²
C
in
L
ul
d (u
(VD
e (V
No
Full
nt M
nt F
)
a
g
t
t
e
e
e
o
a
n
n
r
r
%
g
t
L
r
r
(
l
e
e
rr
rr
y
lta
or
Vo
Cu
Cu
t Vo
t Cu put Cu
ienc
acit
put
put
put
Inpu
Inpu
In
Out
Out
Out
Effic
Cap
SINGLE OUTPUT
P44TG-243R3E4:1LF
P44TG-245R1E4:1LF
P44TG-2412E4:1LF
P44TG-2415E4:1LF
P44TG-483R3E4:1LF
P44TG-485R1E4:1LF
P44TG-4812E4:1LF
P44TG-4815E4:1LF
9-36
9-36
9-36
9-36
18-75
18-75
18-75
18-75
15
15
15
15
15
15
15
15
573
581
574
574
286
290
287
287
3.3
5.1
12
15
3.3
5.1
12
15
0
0
0
0
0
0
0
0
3500
2400
1000
800
3500
2400
1000
800
87
89
90
90
87
89
90
90
2000
2000
430
300
2000
2000
430
300
DUAL OUTPUT
P44TG-2405Z4:1LF
P44TG-2412Z4:1LF
P44TG-2415Z4:1LF
P44TG-4805Z4:1LF
P44TG-4812Z4:1LF
P44TG-4815Z4:1LF
9-36
9-36
9-36
18-75
18-75
18-75
15
15
15
15
15
15
595
574
574
297
287
287
±5
± 12
± 15
±5
± 12
± 15
0
0
0
0
0
0
± 1200
± 500
± 400
± 1200
± 500
± 400
87
90
90
87
90
90
± 1250
± 200
± 120
± 1250
± 200
± 120
If you need other specifications, please enquire.
Notes:
PMV-Series – P44TG-xxxxE/Z4:1MLF – Single and Dual Output – DIP24 - Metal Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/4
Package / Pinning / Derating
27.94
(1.10)
15.24
(0.60)
1
All dimensions are typical in millimeters (inches).
- Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002)
- Pin pitch tolerance: +/-0.35 (+/-0.014)
- Case tolerance +/-0.5 (+/-0.02)
Standard Drawing
For exact pinning please see connection table!
Specification may change without notice.
12
Bottom View
24
13
2.54
(0.10)
DIP24 – METAL CASE
2.00
(0.08)
10.20
(0.40)
20.30
(0.80)
PEAK
Modelcode
Datecode
31.80
(1.25)
3.05
(0.12)
#
1
2
3
9
11
14
16
22
23
others
PIN CONNECTIONS
SINGLE
DUAL
Remote Ctrl. Remote Ctrl.
- Vin
- Vin
- Vin
- Vin
Omitted
Common
N.C.
- Vout
+Vout
+Vout
- Vout
Common
+Vin
+Vin
+Vin
+Vin
Omitted
Omitted
PMV-Series – P44TG-xxxxE/Z4:1MLF – Single and Dual Output – DIP24 - Metal Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/4
App Notes:
EMC Characteristics
Radiated Emissions
EN55022
5
EN55022
Conducted Emissions
ESD
EN61000-4-2
RS
EN61000-4-3
6
EN61000-4-4
EFT
6
EN61000-4-5
Surge
6
EN61000-4-6
CS
PFMF
EN61000-4-8
Over Voltage Protection (Zender diode clamp)
3.3 Vout: 3.9 V
5.1 Vout 6.2 V
12 Vout 15 V
15 Vout 18 V
± 5 Vout ± 6.2 V
± 12 Vout ± 15 V
± 15 Vout ± 18 V
CLASS A
CLASS A
Perf. Criteria B
Perf. Criteria A
Perf. Criteria B
Perf. Criteria B
Perf. Criteria A
Perf. Criteria A
The Remote on/off controll:
ON:
3.0 - 12.0 VDC or open circuit
OFF:
0 - 1.2 VDC or short circuit PIN 1 and PIN 2 / 3
OFF idle current: 5.0 mA, typ.
C1: 2.2uF, 100V
L: 12uH
C2: 2.2uH, 100V
1
= One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%.
= Tested by minimal Vin and constant resistive load.
3
= Measured with 20MHz bandwidth and 1.0uF ceramic capacitor.
4
= Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io )
5
= Input filter components (C1, L, C2) are used to help meet conducted emissions requirement for the module.
These components should be mounted as close as possible to the module; and all leads should be minimized to decrease
6
= An external filter capacitor is required if the module has to meet EN61000-4-4 and EN61000-4-5 and EN61000-4-.
The filter capacitor Peak suggest: Nippon - chemi - con KY series, 330uF/100V
2
Notes:
PMV-Series – P44TG-xxxxE/Z4:1MLF – Single and Dual Output – DIP24 - Metal Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 4/4