UNISONIC TECHNOLOGIES CO., LTD UA8316 Preliminary LINEAR INTEGRATED CIRCUIT IGBT GATE DRIVER DESCRIPTION Integrating IGBT gate drive circuits on a single chip, The UTC UA8316 is a dedicated IC and a high current can directly drive IGBT. FEATURES * A high current can directly drive IGBT * Can directly control from a microcontroller Source current: -200mA (max), sink current 1A (max) * Protect the IGBT gate at power on via a diode ORDERING INFORMATION Ordering Number Note: Lead Free Halogen Free UA8316L-G07-T UA8316G-G07-T xx: Output Voltage, refer to Marking Information. www.unisonic.com.tw Copyright © 2012 Unisonic Technologies Co., Ltd Package Packing SIP-7 Tube 1 of 6 QW-R122-010.a UA8316 Preliminary PIN CONFIGURATION PIN DESCRIPTION PIN NO. 1 2 3 4 5 6 7 PIN NAME GATEIN VCC N.C. GND SI SO DI LINEAR INTEGRATED CIRCUIT DESCRIPTION Gate Signal Input Power Supply Not Connected Ground IGBT Gate Drive (Sink Side) IGBT Gate Drive (Source Side) IGBT Gate Protector Diode UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 6 QW-R122-010.a UA8316 LINEAR INTEGRATED CIRCUIT BLOCK DIAGRAM 30kΩ Preliminary UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 6 QW-R122-010.a UA8316 Preliminary LINEAR INTEGRATED CIRCUIT ABSOLUTE MAXIMUM RATING (TA=25°C, Unless otherwise specified) PARAMETER SYMBOL RATINGS UNIT Collector Supply Voltage VCC 25 V Input Voltage VIN GND-0.3~VCC+0.3 V Power Dissipation (Note 2) PD 925 mW Operating Temperature TOPR -20~+85 °C Storage Temperature TSTG -55~+150 °C Note: 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. 2. When TA>25°C, PD decreases 7.4mW per degree. ELECTRICAL CHARACTERISTICS (TA=25°C, Unless otherwise specified, VCC=20V) PARAMETER SUPPLY VOLTAGE BLOCK Operating Supply Voltage Range Current Consumption 1 Current Consumption 2 GATEIN PIN Input Dynamic Range Threshold Voltage 1 Threshold Voltage 2 Input Current Input Frequency (Reference) SI PIN “L” Level Output Voltage 1 “L” Level Output Voltage 2 “L” Level Output Voltage 3 “L” Level Output Voltage 4 (Output Voltage At Low Supply Voltage) “L” Level Output Voltage 5 (Output Voltage At Low Supply Voltage) Off Leakage Current SO PIN “H” Level Output Voltage 1 “H” Level Output Voltage 2 Off Leakage Current DI PIN Input Clamp Voltage 1 Input Clamp Voltage 2 SYMBOL VCC ICC1 ICC2 TEST CONDITIONS VCC=20V, GATEIN=”H”, No Load VCC=20V, GATEIN=”L”, No Load VIN GATEIN VTH GATE1 GATE Signal L→H VTH GATE2 GATE Signal H→L IIN GATE VIN=5V When Load C=5600pF, R=10kΩ FIN GATE Connected VOL SI1 VOL SI2 VOL SI3 VOL SI4 VOL SI5 IOFF SI VOH SO1 VOH SO2 IOFF SO VF DI1 VF DI2 MIN TYP MAX UNIT 7 0.7 4.2 1.25 6.25 24 1.9 8.8 V mA mA VCC-2.2 3 249 V V V μA 50 KHz 0.7 2 1 V V V 1 V 2 V 1 μA 1 V V μA VCC+1.5 VCC+1.0 V V 0 2.63 2.27 167 1.5 125 VGATEIN=0V, IOL=30mA VGATEIN=0V, IOL=1A VCC=7V, VGATEIN=0V, IOL=30mA 2V≤VCC<7V, VGATEIN=0V, No Load 2V≤VCC<7V, VGATEIN=0V, IOL=30mA VGATEIN=6V, VIN=20V VGATEIN=6V, IOH=-30mA VGATEIN=6V, IOH=-200mA VGATEIN=0V, VIN=0V -1 VCC-2 VCC-5 -1 IIN=500mA VCC=0V, IIN=300mA AC CHARACTERISTICS (VCC=20V, TA=25°C, Unless otherwise specified) PARAMETER Propagation Delay Time 1 Propagation Delay Time 2 Output Fall Time SYMBOL TEST CONDITIONS tPLL See Test Circuit Diagram tPHH See Test Circuit Diagram tF See Test Circuit UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN TYP MAX 2 2 0.5 UNIT μs μs μs 4 of 6 QW-R122-010.a UA8316 Preliminary LINEAR INTEGRATED CIRCUIT AC CHARACTERISTICS TEST CONDITIONS A. Propagation delay time 1 (tPLL) Time from input of “L” level to GATEIN pin until output reaches 1V Input 50% Output 1V tPLL B. Propagation delay time 2 (tPHH) Time from input of “H” level to GATEIN pin until output starts to rise C. Output fall time (tF) Output fall time from 90% to 10% TEST CIRCUIT UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 6 QW-R122-010.a UA8316 LINEAR INTEGRATED CIRCUIT TYPICAL APPLICATION CIRCUIT 150Ω 30kΩ Preliminary UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 6 QW-R122-010.a