DATASHEET Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Pin Configuration *FS2//REF0 VDD X1 X2 GND GND 3V66-0 3V66-1 3V66-2 VDD VDD PCICLK_F PCICLK0 GND PCICLK1 PCICLK2 GND PCICLK3 PCICLK4 PCICLK5 VDD VDD GND GND 48MHz_0 48MHz_1 VDD FS0 810/810E and 815 type chipset. Output Features: • • • • • 3 CPU (2.5V) (up to 133MHz achievable through I2C) 9 SDRAM (3.3V) (up to 133MHz achievable through I2C) 7 PCI (3.3 V) @33.3MHz 2 IOAPIC (2.5V) @ 33.3 MHz 3 Hublink clocks (3.3 V) @ 66.6 MHz 2 (3.3V) @ 48 MHz (Non spread spectrum) 1 REF (3.3V) @ 14.318 MHz Features: • • • • • Supports spread spectrum modulation, 0 to -0.5% down spread. I2C support for power management Efficient power management scheme through PD# Uses external 14.138 MHz crystal Alternate frequency selections available through I2C control. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 ICS9250-27 Recommended Application: • • ICS9250-27 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 GND IOAPIC0 IOAPIC1 VDDL CPUCLK0 VDDL0 CPUCLK1 CPUCLK2 GNDL GND SDRAM0 SDRAM1 VDD SDRAM2 SDRAM3 GND SDRAM4 SDRAM5 VDD SDRAM6 SDRAM7 GND SDRAM_F VDD PD# SCLK SDATA FS1 56-Pin 300mil SSOP * This input has a 50KΩ pull-down to GND. Block Diagram Functionality X1 X2 XTAL OSC REF0 PLL1 Spread Spectrum /2 /3 VDDL FS2 FS1 FS0 X X 0 0 0 1 0 1 0 0 1 1 1 1 0 1 1 1 CPU66/100/133 (2:0) 3 FS (2:0) PD# 3 Control Logic 8 3V66 (2:0) SDRAM (7:0) SDRAM_F SDATA /2 SCLK 6 Config Reg PCICLK (5:0) Function Tristate Test Active CPU = 66MHz SDRAM = 100MHz Active CPU = 100MHz SDRAM = 100MHz Active CPU = 133MHz SDRAM = 133MHz Active CPU = 133MHz SDRAM = 100MHz PCICLK_F /2 2 PLL2 2 IOAPIC (1:0) VDDL Power Groups AVDD = Pin 22 Analog power for PLL AGND = Pin 23 Analog ground VDD48 = Pin 27 Analog power for 48MHz PLL GND = Pin 24 Analog ground for 48MHz PLL 48MHz (1:0) IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 1 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM General Description The ICS9250-27 is a single chip clock solution for 810/810E and 815 type chipset. It provides all necessary clock signals for such a system. Spread spectrum may be enabled through I2C programming. Spread spectrum typically reduces EMI by 8dB to 10 dB. This simplifies EMI qualification without resorting to board design iterations or costly shielding. The ICS925027 employs a proprietary closed loop design, which tightly controls the percentage of spreading over process and temperature variations. Pin Description PIN NUMBER 1 PIN NAME FS2 TYPE IN 3 X1 IN 4 X2 OUT 3.3V, 14.318MHz reference clock output. Cr ystal input, has inter nal load cap (33pF) and feedback resistor from X2 Cr ystal output, nominally 14.318MHz. Has inter nal load cap (33pF) PWR Ground pins for 3.3V supply 3V66 (2:0) OUT 3.3V Fixed 66MHz clock outputs for HUB VDD PWR 3 . 3 V p ow e r s u p p l y PCICLK_F OUT Free r unning 3.3V PCI clock output PCICLK (5:0) OUT 3.3V PCI clock outputs 25 48MHz_0 OUT 3.3V Fixed 48MHz clock outputs for USB 26 48MHz_1 OUT 3.3V fixed 48MHz clock output. Stronger output for graphics/video interface (minimum 1V/ns edge rate) Function Select pins. Determines CPU frequency, all output functionality. Please refer to Functionality table on page 1 REF0 5, 6, 14, 17, 23, 24, 35, 41, 47, GND 48, 56 9, 8, 7 2, 10, 11, 21, 22, 27, 33, 38, 44 12 20, 19, 18, 16, 15, 13 OUT DESCRIPTION Function Select pin. Determines CPU frequency, all output functionality 29, 28 FS (1:0) IN 30 SDATA I/O Data pin for I2C circuitr y 5V tolerant 31 SCLK IN Clock pin of I2C circuitr y 5V tolerant 32 36, 37, 39, 40, 42, 43, 45, 46 PD# IN Asynchronous active low input pin used to power down the device into a low power state. The inter nal clocks are disabled and the VCO a n d t h e c r y s t a l a r e s t o p p e d . T h e l a t e n c y o f t h e p ow e r d ow n w i l l n o t b e g r e a t e r t h a n 3 m s. 3.3V output r unning 100MHz. All SDRAM outputs can be tur ned off t h r o u g h I 2C SDRAM (7:0) OUT SDRAM_F OUT 3 . 3 V f r e e r u n n i n g 1 0 0 M H z S D R A M , c a n n o t b e t u r n e d o f f t h r o u g h I 2C CPUCLK (2:0) OUT 2.5V Host bus clock output. 66MHz, 100MHz or 133MHz depending o n F S p i n s. 51, 53 VDDL PWR 2.5V power suypply for CPU & IOAPIC 54, 55 IOAPIC (1:0) OUT 2.5V clock outputs r unning at 33.3MHz. 34 49, 50, 52 IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 2 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Power Down Waveform Note 1. After PD# is sampled active (Low) for 2 consective rising edges of CPUCLKs, all the output clocks are driven Low on their next High to Low tranistiion. 2. Power-up latency <3ms. 3. Waveform shown for 100MHz Maximum Allowed Current Max 2.5V supply consumption Max discrete cap loads, Vddq2 = 2.625V All static inputs = Vddq3 or GND 815 Condition Max 2.5V supply consumption Max discrete cap loads, Vddq2 = 3.465V All static inputs = Vddq3 or GND Powerdown Mode (PWRDWN# = 0 10mA 10mA Full Active 66MHz FS[2:0] = 010 70mA 280mA Full Active 100MHz FS[2:0] = 011 100mA 280mA Full Active 133MHz FS[2:0] = 111 Clock Enable Configuration PD# CPUCLK SDRAM IOAPIC 66MHz PCICLK REF, 48MHz Osc VCOs 0 LOW LOW LOW LOW LOW LOW OF F OFF 1 ON ON ON ON ON ON ON ON IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 3 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Truth Table FS2 FS1 FS0 CPU SDRAM 3V66 PCI 48MHz REF IOAPIC X 0 0 Tristate Tristate Tristate Tristate Tristate Tristate Tristate X 0 1 TCLK/2 TCLK/2 TCLK/3 TCLK/6 TCLK/2 TCLK TCLK/6 0 1 0 66.6 MHz 100 MHz 66.6 MHz 33.3 MHz 48 MHz 14.318 MHz 33.3 MHz 0 1 1 100 MHz 100 MHz 66.6 MHz 33.3 MHz 48 MHz 14.318 MHz 33.3 MHz 1 1 0 133 MHz 133 MHz 66.6 MHz 33.3 MHz 48 MHz 14.318 MHz 33.3 MHz 1 1 1 133 MHz 100 MHz 66.6 MHz 33.3 MHz 48 MHz 14.318 MHz 33.3 MHz Byte 0: Control Register (1 = enable, 0 = disable) Bit Bit 7 Bit 6 Bit 5 Bit 4 Pin# Bit 3 Bit 2 Bit 1 Bit 0 26 25 49 Name Reserved ID Reserved ID Reserved ID Reserved ID SpreadSpectrum (1=On/0=Off) 48MHz 1 48MHz 0 CPUCLK2 PWD 0 0 0 0 Description (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) 1 (Active/Inactive) 1 1 1 (Active/Inactive) (Active/Inactive) (Active/Inactive) Note: Reserved ID bits must be wirtten as "0". Byte 1: Control Register (1 = enable, 0 = disable) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 B it 0 Pin# 36 37 39 40 42 43 45 46 Name SDRAM7 SDRAM6 SDRAM5 SDRAM4 SDRAM3 SDRAM2 SDRAM1 SDRAM0 PWD 1 1 1 1 1 1 1 1 Description (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) Notes: 1. Inactive means outputs are held LOW and are disabled from switching. These outputs are designed to be configured at power-on and are not expected to be configured during the normal modes of operation. 2. PWD = Power on Default IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 4 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Byte 2: Control Register (1 = enable, 0 = disable) Bit Bit 7 Bit 6 Bit 5 B it 4 Bi t 3 B it 2 Bi t 1 Bit 0 Pin# 9 20 19 18 16 15 13 - Name 3V66-2 (AGP) PCICLK5 PCICLK4 PCICLK3 PCICLK2 PCICLK1 PCICLK0 Undefined bit PWD 1 1 1 1 1 1 1 X Description (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) Notes: 1. Inactive means outputs are held LOW and are disabled from switching. These outputs are designed to be configured at power-on and are not expected to be configured during the normal modes of operation. 2. PWD = Power on Default 3. Undefined bit can be wirtten with either a "1" or "0". Byte 3: ICS Reserved Functionality and frequency select register (Default as noted in PWD) Bit Desctiption PWD Bit7 ICS Reserved bit (Note 2) 0 Bit6 ICS Reserved bit (Note 2) 0 Bit5 ICS Reserved bit (Note 2) 0 Bit4 ICS Reserved bit (Note 2) 0 Bit3 ICS Reserved bit (Note 2) 0 Bit2 Undefined bit (Note 3) X Bit1 Undefined bit (Note 3) X Bit 0 CPUCLK SDRAM MHz MHz 3V66 MHz PCICLK IOAPIC MHz MHz Bit 0 FS0 FS1 0 0 0 66.66 100.0 66.66 33.33 33.33 0 1 0 100.0 100.0 66.66 33.33 33.33 0 0 1 133.32 133.32 66.66 33.33 33.33 0 1 1 133.32 100.0 66.66 33.33 33.33 1 0 0 66.66 100.0 66.66 33.33 33.33 1 1 0 100.0 100.0 66.66 33.33 33.33 1 0 1 133.32 133.32 66.66 33.33 33.33 1 1 1 133.32 133.32 66.66 33.33 33.33 0 Note 1 Note 1: For system operation, the BSEL lines of the CPU will program FS0, FS2 for the appropriate CPU speed, always with SDRAM = 100MHz. After BIOS verifies the SDRAM is PC133 speed, then bit 0 can be written from the default 0 to 1 to change the SDRAM output frequency from 100MHz to 133MHz. This will only change if the CPU is at the 133MHz FSB speed as shown in this table. The CPU, 3v66, PCI, and IOAPIC clocks will be glitch free during this transition, and only SDRAM will change. Note 2: "ICS RESERVED BITS" must be writtern as "O". Note3: Undefined bits can be written either as "1 or 0" IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 5 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Byte 4: Reserved Register (1 = enable, 0 = disable) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Pin# - Name Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved PWD 0 0 0 0 0 0 0 0 Description (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) PWD 0 0 0 0 0 0 0 0 Description (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) (Active/Inactive) Byte 5: Reserved Register (1 = enable, 0 = disable) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Pin# - Name Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Notes: 1. Inactive means outputs are held LOW and are disabled from switching. These outputs are designed to be configured at power-on and are not expected to be configured during the normal modes of operation. 2. PWD = Power on Default Group Timing Relationship Table1 Group CPU 66MHz SDRAM 100MHz CPU 100MHz SDRAM 100MHz CPU 133MHz SDRAM 100MHz CPU 133MHz SDRAM 133MHz Offset Tolerance Offset Offset Tolerance Offset CPU to SDRAM 2.5ns 500ps 5.0ns 500ps 0.0ns 500ps 3.75ns 500ps CPU to 3V66 7.5ns 500ps 5.0ns 500ps 0.0ns 500ps 0.0ns 500ps SDRAM to 3V66 0.0ns 500ps 0.0ns 500ps 0.0ns 500ps 3.75ns 500ps 3V66 to PCI 1.5-3.5ns N/A 1.5-3.5ns N/A 1.5-3.5ns N/A 1.5 -3.5ns N/A IOAPIC to PCI USB & DOT 0.0ns Asynch 1.0ns N/A 0.0ns Asynch 1.0ns N/A 0.0ns Asynch 1.0ns N/A 0.0ns Asynch 1.0ns N/A Tolerance IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Tolerance 0395F—01/25/10 6 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Absolute Maximum Ratings Core Supply Voltage 4.6 V I/O Supply Voltage 3.6V Logic Inputs GND –0.5 V to VDD +0.5 V Ambient Operating Temperature 0°C to +70°C Storage Temperature –65°C to +150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Electrical Characteristics - Input/Supply/Common Output Parameters TA = 0 - 70C; Supply Voltage VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5% (unless otherwise stated) PARAMETER SYMBOL CONDITIONS MIN TYP Input High Voltage VIH 2 VSS-0.3 Input Low Voltage VIL VIN = VDD -5 Input High Current IIH VIN = 0 V; Inputs with no pull-up resistors -5 2 IIL1 Input Low Current VIN = 0 V; Inputs with pull-up resistors -200 -100 IIL2 97 CL = 0 pF; Select @ 66 MHz 91 CL = 0 pF; Select @ 100 MHz 100 CL = 0 pF; Select @ 133 MHz IDD3.3OP 295 CL = Max loads; Select @ 66 MHz 280 CL = Max loads; Select @ 100 MHz Operating Supply Current IDD2.5OP Powerdown Current Input Frequency Pin Inductance Input Capacitance1 1 Transition time 1 Settling time Clk Stabilization1 Delay1 1 IDD3.3PD IDD.25PD Fi Lpin CIN COUT CINX MAX VDD+0.3 0.8 5 µA 115 110 165 330 320 CL = Max loads; Select @ 133 MHz CL = 0 pF; Select @ 66 MHz CL = 0 pF; Select @ 100 MHz CL = 0 pF; Select @ 133 MHz CL = Max loads; Select @ 66 MHz CL = Max loads; Select @ 100 MHz 300 16 25 26 19 34 395 19 35 40 30 50 CL = Max loads; Select @ 133 MHz CL = Max loads Input address VDD or GND VDD = 3.3 V 40 220 <1 14.318 7 70 400 10 16 mA mA mA mA µA 45 MHz nH pF pF pF To 1st crossing of target frequency 5 ms Ts From 1st crossing to 1% target frequency 5 ms TSTAB tPZH,tPZL tPHZ,tPLZ From VDD = 3.3 V to 1% target frequency Output enable delay (all outputs) Output disable delay (all outputs) 5 10 10 ms ns ns Ttrans Logic Inputs Output pin capacitance X1 & X2 pins 12 UNITS V V µA 5 6 27 1 1 Guaranteed by design, not 100% tested in production. IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 7 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Electrical Characteristics - CPU TA = 0 - 70C; VDDL = 2.5 V +/-5%; CL = 10-20 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS Output Impedance 1 MIN TYP MAX UNITS VO = VDD*(0.5) 13.5 22 45 Ω VO = VDD*(0.5) IOH = -1 mA IOL = 1 mA VOH @ MIN = 1.0 V VOH @ MAX = 2.375 V VOL @ MIN = 1.2 V VOL @ MAX = 0.3 V 13.5 2 23 45 Ω V V Output Impedance Output High Voltage Output Low Voltage RDSN2B VOH2B VOL2B Output High Current IOH2B Output Low Current IOL2B Rise Time1 tr2B VOL = 0.4 V, VOH = 2.0 V 0.4 1.1 1.6 ns tf2B VOH = 2.0 V, VOL = 0.4 V 0.4 1.1 1.6 ns Duty Cycle1 dt2B VT = 1.25 V, 66, 100 MHz VT = 1.25 V, 133 MHz 45 45 50 53 55 55 % Skew window1 Jitter, Cycle-to-cycle1 tsk2B VT = 1.25 V 118 175 ps tjcyc-cyc2B VT = 1.25 V 148 250 ps Fall Time 1 RDSP2B 1 1 0.4 -27 27 -68 -9 54 11 -27 30 mA mA Guaranteed by design, not 100% tested in production. Electrical Characteristics - 3V66 TA = 0 - 70C; VDD = 3.3 V +/-5%; CL = 10-20 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS Output Impedance 1 MIN TYP MAX UNITS VO = VDD*(0.5) 12 17 55 Ω VO = VDD*(0.5) IOH = -1 mA IOL = 1 mA VOH @ MIN = 1.0 V VOH @ MAX = 3.135 V VOL @ MIN = 1.95 V VOL @ MAX = 0.4 V 12 2.4 18 55 Ω V V -33 Output Impedance Output High Voltage Output Low Voltage RDSN1 VOH1 VOL1 Output High Current IOH1 Output Low Current IOL1 Rise Time1 tr1 VOL = 0.4 V, VOH = 2.4 V 0.4 1.2 1.8 ns tf1 dt1 VOH = 2.4 V, VOL = 0.4 V 0.4 1.3 1.8 ns VT = 1.5 V 45 50 55 % tsk1 VT = 1.5 V 82 175 ps tjcyc-cyc1 VT = 1.5 V 123 500 ps Fall Time 1 1 Duty Cycle Skew window1 Jitter, Cycle-to-cycle1 1 RDSP1 1 0.55 30 -108 -9 95 29 -33 38 mA mA Guaranteed by design, not 100% tested in production. IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 8 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Electrical Characteristics - IOAPIC TA = 0 - 70C; VDDL = 2.5 V +/-5%; CL = 10-20 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS Output Impedance Output Impedance Output High Voltage Output Low Voltage 1 RDSN4B VOH4B VOL4B MIN TYP MAX UNITS VO = VDD*(0.5) 9 21.5 30 Ω VO = VDD*(0.5) IOH = -1 mA IOL = 1 mA VOH @ MIN = 1.0 V VOH @ MAX = 2.375 V VOL @ MIN = 1.2 V VOL @ MAX = 0.3 V 9 2 23 30 Ω V V -27 -68 -9 54 11 0.4 Output High Current IOH4B Output Low Current IOL4B Rise Time1 tr4B VOL = 0.4 V, VOH = 2.0 V 0.4 1.1 1.6 ns Fall Time1 tf4B dt4B VOH = 2.0 V, VOL = 0.4 V 0.4 1.1 1.6 ns VT = 1.25 V 45 50 55 % 123 500 ps 1 Duty Cycle Jitter, Cycle-to-cycle1 1 RDSP4B 1 tjcyc-cyc4B 27 VT = 1.25 V -27 30 mA mA Guaranteed by design, not 100% tested in production. Electrical Characteristics - SDRAM TA = 0 - 70C; VDD = 3.3 V +/-5%; CL = 20-30 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS Output Impedance Output Impedance Output High Voltage Output Low Voltage 1 RDSN3 VOH3 VOL3 MIN TYP MAX UNITS VO = VDD*(0.5) 10 14 24 Ω VO = VDD*(0.5) IOH = -1 mA IOL = 1 mA VOH @ MIN = 2.0 V VOH @ MAX = 3.135 V VOL @ MIN = 1.0 V VOL @ MAX = 0.4 V 10 2.4 18 24 Ω V V -54 -92 -16 68 29 0.4 Output High Current IOH3 Output Low Current IOL3 Rise Time1 tr3 VOL = 0.4 V, VOH = 2.4 V 0.4 1 1.6 ns VOH = 2.4 V, VOL = 0.4 V 0.4 1.5 1.6 ns Duty Cycle Skew window1 tf3 dt3 VT = 1.5 V 45 52 55 % tsk3 VT = 1.5 V 164 250 ps Jitter, Cycle-to-cycle1 tjcyc-cyc3 VT = 1.5 V, 66, 100 MHz 180 250 ps Fall Time 1 1 1 RDSP3 1 54 -46 53 mA mA Guaranteed by design, not 100% tested in production. IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 9 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Electrical Characteristics - PCI TA = 0 - 70C; VDD = 3.3 V +/-5%; CL = 10-30 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS Output Impedance Output Impedance Output High Voltage Output Low Voltage 1 RDSN1 VOH1 VOL1 MIN TYP VO = VDD*(0.5) 12 14 55 Ω VO = VDD*(0.5) IOH = -1 mA IOL = 1 mA VOH @ MIN = 1.0 V VOH @ MAX = 3.135 V VOL @ MIN = 1.95 V VOL @ MAX = 0.4 V 12 2.4 18 55 Ω V V -33 -106 -14 94 29 MAX UNITS 0.55 Output High Current IOH1 Output Low Current IOL1 Rise Time1 tr1 VOL = 0.4 V, VOH = 2.4 V 0.4 1.3 Fall Time1 tf1 dt1 VOH = 2.4 V, VOL = 0.4 V 0.4 VT = 1.5 V 45 tsk1 tjcyc-cyc1 Duty Cycle1 Skew window1 Jitter, Cycle-to-cycle1 1 RDSP1 1 30 -33 38 mA mA 2 ns 1.4 2 ns 52 55 % VT = 1.5 V 304 500 ps VT = 1.5 V 170 500 ps Guaranteed by design, not 100% tested in production. Electrical Characteristics - REF, 48MHz_0 (Pin 25) TA = 0 - 70C; VDD = 3.3 V +/-5%; CL = 10-20 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS Output Impedance Output Impedance Output High Voltage Output Low Voltage 1 RDSN5 VOH15 VOL5 MIN TYP VO = VDD*(0.5) 20 32.6 60 Ω VO = VDD*(0.5) IOH = -1 mA IOL = 1 mA VOH @ MIN = 1.0 V VOH @ MAX = 3.135 V VOL @ MIN = 1.95 V VOL @ MAX = 0.4 V 20 2.4 31 60 Ω V V -29 -54 -11 54 16 IOH5 Output Low Current IOL5 Rise Time1 tr5 VOL = 0.4 V, VOH = 2.4 V 0.4 1.4 Fall Time1 tf5 dt5 VOH = 2.4 V, VOL = 0.4 V 0.4 VT = 1.5 V 45 tjcyc-cyc5 tjcyc-cyc5 Duty Cycle Jitter, Cycle-to-cycle1 Jitter, Cycle-to-cycle1 MAX UNITS 0.55 Output High Current 1 1 RDSP5 1 29 -23 27 mA mA 4 ns 1.7 4 ns 53 55 % VT = 1.5 V, Fixed clocks 215 500 ps VT = 1.5 V, Ref clocks 930 1000 ps Guaranteed by design, not 100% tested in production. IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 10 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Electrical Characteristics - 48MHz_1 (Pin 26) TA = 0 - 70C; VDD = 3.3 V +/-5%; CL = 10-15 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS Output Impedance Output Impedance Output High Voltage Output Low Voltage 1 RDSN3 VOH3 VOL3 MIN TYP MAX UNITS VO = VDD*(0.5) 10 16.7 24 Ω VO = VDD*(0.5) IOH = -1 mA IOL = 1 mA VOH @ MIN = 2.0 V VOH @ MAX = 3.135 V VOL @ MIN = 1.0 V VOL @ MAX = 0.4 V 10 2.4 18.4 24 Ω V V -54 -82 -20 95 28 0.55 Output High Current IOH3 Output Low Current IOL3 Rise Time1 tr3 VOL = 0.4 V, VOH = 2.4 V 0.4 1.1 1.6 ns Fall Time1 tf3 dt3 tsk3 VOH = 2.4 V, VOL = 0.4 V 0.4 1.1 1.6 ns VT = 1.5 V VT = 1.5 V 45 51 116 55 250 % ps 196 500 ps Duty Cycle1 Skew Jitter, Cycle-to-cycle1 1 RDSP3 1 tjcyc-cyc3B 54 VT = 1.5 V -46 53 mA mA Guaranteed by design, not 100% tested in production. IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 11 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0ns 10ns 20ns 30ns 40ns Cycle Repeats CPU 66MHz CPU 100MHz CPU 133MHz SDRAM 100MHz SDRAM 133MHz 3.3V 66MHz PCI 33MHz IOAPIC 33MHz REF 14.318MHz USB 48MHz Group Offset Waveforms IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 12 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM General I2C serial interface information The information in this section assumes familiarity with I2C programming. How to Write: How to Read: • • • • • • • • • • • • • • • • Controller (host) sends a start bit. Controller (host) sends the write address D2 (H) ICS clock will acknowledge Controller (host) sends a dummy command code ICS clock will acknowledge Controller (host) sends a dummy byte count ICS clock will acknowledge Controller (host) starts sending first byte (Byte 0) through byte 5 • ICS clock will acknowledge each byte one at a time. Controller (host) will send start bit. Controller (host) sends the read address D3 (H) ICS clock will acknowledge ICS clock will send the byte count Controller (host) acknowledges ICS clock sends first byte (Byte 0) through byte 5 Controller (host) will need to acknowledge each byte Controller (host) will send a stop bit How to Read: How to Write: Controller (Host) Start Bit Address D2(H ) Controller (Host) Start Bit Address D3(H ) ICS (Slave/Receiver) ICS (Slave/Receiver) ACK Byte Count ACK Dummy Command Code ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK Stop Bit Byte 0 Dummy Byte Count Byte 1 Byte 0 Byte 2 Byte 1 Byte 3 Byte 2 Byte 4 Byte 3 Byte 5 Byte 4 Byte 5 ACK Stop Bit Notes: 1. 2. 3. 4. 5. 6. The ICS clock generator is a slave/receiver, I2C component. It can read back the data stored in the latches for verification. Read-Back will support Intel PIIX4 "Block-Read" protocol. The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode) The input is operating at 3.3V logic levels. The data byte format is 8 bit bytes. To simplify the clock generator I2C interface, the protocol is set to use only "Block-Writes" from the controller. The bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those two bytes. The data is loaded until a Stop sequence is issued. At power-on, all registers are set to a default condition, as shown. IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 13 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 56-Lead, 300 m il Body, 25 m il, SSOP SYMBOL A A1 b c D E E1 e h L N α In Millimeters COMMON DIMENSIONS MIN MAX 2.41 2.80 0.20 0.40 0.20 0.34 0.13 0.25 SEE VARIATIONS 10.03 10.68 7.40 7.60 0.635 BASIC 0.38 0.64 0.50 1.02 SEE VARIATIONS 0° 8° In Inches COMMON DIMENSIONS MIN MAX .095 .110 .008 .016 .008 .0135 .005 .010 SEE VARIATIONS .395 .420 .291 .299 0.025 BASIC .015 .025 .020 .040 SEE VARIATIONS 0° 8° VARIATIONS N 56 D mm. MIN 18.31 D (inch) MAX 18.55 MIN .720 MAX .730 Reference Doc.: JEDEC Publication 95, MO-118 10-0034 Ordering Information 9250yF-27LF-T Example: XXXX y F - PPP LF - T Designation for tape and reel packaging RoHS Compliant (Optional) Pattern Number (2 or 3 digit number for parts with ROM code patterns) Package Type F=SSOP Revision Designator (will not correlate with datasheet revision) Device Type (consists of 3 to 7 digit numbers) IDTTM Frequency Generator and Integrated Buffers for Celeron & PII/IIITM 0395F—01/25/10 14 ICS9250-27 Frequency Generator and Integrated Buffers for Celeron & PII/IIITM Revision History Rev. C D E F Issue Date 8/17/2005 10/25/2005 9/11/2008 1/25/2010 Description Added LF Ordering Information 2 Removed "Contact ICS for an I C programming application" note reference. Corrected typo on pin# 28/29 pin description Updated document template Page # 14 13 2 Innovate with IDT and accelerate your future networks. Contact: www.IDT.com TM For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 408-284-6578 [email protected] Corporate Headquarters Asia Pacific and Japan Europe Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800 345 7015 +408 284 8200 (outside U.S.) Integrated Device Technology Singapore (1997) Pte. Ltd. Reg. No. 199707558G 435 Orchard Road #20-03 Wisma Atria Singapore 238877 +65 6 887 5505 IDT Europe, Limited Prime House Barnett Wood Lane Leatherhead, Surrey United Kingdom KT22 7DE +44 1372 363 339 © 2009 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT, ICS, and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA 15