SFH6916 www.vishay.com Vishay Semiconductors Optocoupler, Phototransistor Output, Quad Channel, SOP-16, Half Pitch Mini-Flat Package FEATURES i179076-4 A 1 16 C C 2 15 E A 3 14 C C 4 13 E A 5 12 C C 6 11 E • Temperature stable A 7 10 C • Low coupling capacitance C 8 9 E • SOP (small outline package) • Isolation test voltage, 3750 VRMS (1.0 s) • High collector emitter voltage, VCEO = 70 V • Low saturation voltage • Fast switching times • End stackable, 0.050" (1.27 mm) spacing • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 DESCRIPTION AGENCY APPROVALS The SFH6916 has a GaAs infrared emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a 16 pin 50 mil lead pitch miniflat package. It features a high current transfer ratio, low coupling capacitance, and high isolation voltage. • UL1577, file no. E52744 system code U • CSA 22.2 bulletin 5A, double protection • DIN EN 60747-5-5 (VDE 0884) • CQC GB4943.1-2011 (suitable for installation altitude below 2000 m) The coupling devices are designed for signal transmission between two electrically separated circuits. ORDERING INFORMATION S F H 6 9 1 6 SOP-16 PART NUMBER AGENCY CERTIFIED/PACKAGE CTR (%) UL, cUL 50 to 300 SOP-16, quad channel SFH6916 ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage VR 6 V DC forward current IF 50 mA Surge forward current tp 10 μs IFSM 2.5 A Pdiss 80 mW Collector emitter voltage VCE 70 V Emitter collector voltage VEC 7 V IC 50 mA IC 100 mA Pdiss 150 mW Total power dissipation OUTPUT Collector current Total power dissipation per channel Rev. 2.1, 12-Apr-13 tp = 1.0 ms Document Number: 83687 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH6916 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT t = 1.0 s VISO 3750 VRMS VIO = 500 V, Tamb = 25 °C RIO 1012 °C COUPLER Isolation test voltage between emitter and detector Isolation resistance RIO 1011 Storage temperature range Tstg - 55 to + 125 Ambient temperature range Tamb - 55 to + 100 °C Tj 100 °C 260 °C 700 mW VIO = 500 V, Tamb = 100 °C Junction temperature Soldering temperature (1) max. 10 s dip soldering distance to seating plane 1.5 mm Total power dissipation Ptot Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices. ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL Forward voltage IF = 5 mA Reverse current VR = 6 V MIN. TYP. MAX. UNIT VF 1.15 1.4 V IR 0.01 10 μA INPUT Capacitance CO Thermal resistance CO 14 pF Rthja 1000 K/W OUTPUT Collector emitter leakage current Collector emitter capacitance VCE = 20 V ICEO VCE = 5 V, f = 1 MHz CCE 2.8 pF Rthja 500 K/W IF = 20 mA, IC = 1 mA VCEsat 0.1 f = 1 MHz CC 1 Thermal resistance 100 nA COUPLER Collector emitter saturation voltage Coupling capacitance 0.4 V pF Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. CURRENT TRANSFER RATIO (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. Current transfer ratio IF = 5 mA, VCC = 5 V CTR 50 Rev. 2.1, 12-Apr-13 TYP. MAX. UNIT 300 % Document Number: 83687 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH6916 www.vishay.com Vishay Semiconductors SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Rise time IC = 2 mA, VCC = 10 V, RL = 100 tr 4 μs Fall time IC = 2 mA, VCC = 10 V, RL = 100 tf 3 μs Turn-on time IC = 2 mA, VCC = 10 V, RL = 100 ton 5 μs Turn-off time IC = 2 mA, VCC = 10 V, RL = 100 toff 4 μs μs NON-SATURATED SATURATED Rise time IF = 16 mA, VCC = 5 V, RL = 1.9 k tr 15 Fall time IF = 16 mA, VCC = 5 V, RL = 1.9 k tf 0.5 μs Turn-on time IF = 16 mA, VCC = 5 V, RL = 1.9 k ton 1 μs Turn-off time IF = 16 mA, VCC = 5 V, RL = 1.9 k toff 30 μs IF R L= 100 Ω IC IF R L= 1.9 kΩ V CC = 10 V V CC = 5 V IC 50 Ω 50 Ω isfh6916_02 isfh6916_01 Fig. 1 - Switching Operation (without Saturation) Fig. 2 - Switching Operation (with Saturation) SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL MIN. Climatic classification (according to IEC 68 part 1) MAX. UNIT 55/100/21 Comparative tracking index CTI 175 Peak transient overvoltage VIOTM 6000 Peak insulation voltage VIORM 707 Safety rating - power output TYP. 399 V V PSO 350 mW Safety rating - input current ISI 150 mA Safety rating - temperature TSI 175 °C Creepage distance 5 mm Clearance distance 5 mm Note • As per IEC 60747-5-2, § 7.4.3.8.1, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. Rev. 2.1, 12-Apr-13 Document Number: 83687 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH6916 www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 100 1.5 T = - 25 °C 1.3 T = 0 °C 1.1 T = 100 °C T = 75 °C 0.9 T = 50 °C T = 25 °C Collector Current (mA) VF - Forward Voltage (V) T = - 55 °C isfh6916_03 0.1 1 10 100 0.100 IF = 5.0 mA IF = 2.0 mA 0.010 IF = 1.0 mA 0.4 0.6 0.8 1.0 60 IF = 30 mA 50 IF = 20 mA 40 IF = 15 mA 30 IF = 10 mA 20 IF = 5 mA 10 2 4 6 Fig. 6 - Collector Current vs. Collector Emitter Saturation Voltage CTR - Normalized Ouput Current 70 0 8 10 1.4 1.2 1.0 0.8 0.6 0.4 Normalized to 1.0 at TA = 25 °C IF = 1.0 mA, VCE = 5.0 V 0.2 0.0 - 60 - 40 - 20 VCE - Collector to Emitter Voltage (V) isfh6916_04 0 20 40 60 80 100 TA - Ambient Temperature (°C) isfh6916_07 1000 24 V 40 V 100 12 V 10 1 - 60 - 40 - 20 0 20 40 60 80 100 TA - Ambient Temperature (°C) Fig. 7 - Normalized Output Current vs. Ambient Temperature CTR - Current Transfer Ratio (%) Fig. 4 - Collector Current vs. Collector Emitter Voltage ICEO - Collector to Emitter Dark Current (nA) 0.2 VCE(sat) - Collector Emitter Saturation Voltage (V) isfh6916_06 80 IC - Collector Current (mA) IF = 25 mA IF = 10 mA IF - Forward Current (mA) Fig. 3 - Diode Forward Voltage vs. Forward Current 0 1 0.001 0.0 0.7 0.01 10 300 VCE = 5.0 V 250 Typical for CTR = 250 % 200 150 Typical for CTR = 150 % 100 50 0 0.1 isfh6916_09 1.0 10.0 50 100.0 IF - Forward Current (mA) isfh6916_05 Fig. 5 - Collector to Emitter Dark Current vs. Ambient Temperature Rev. 2.1, 12-Apr-13 Fig. 8 - Current Transfer Ratio vs. Forward Current Document Number: 83687 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH6916 www.vishay.com Vishay Semiconductors Switching Time (µs) 100 ton 10 toff td ts 1 VCC = 5.0 V IC = 2.0 mA 0.1 0 500 1000 1500 2000 RL - Load Resistance (Ω) isfh6916_10 Fig. 9 - Switching Time vs. Load Resistance Switching Time (µs) 1000 IF = 5.0 mA VCC = 5.0 V TA = 25 °C 100 CTR = 150 % tf ts 10 tr td 1 0 100 1000 10 000 100 000 RL - Load Resistance (Ω) isfh6916_11 Fig. 10 - Switching Time vs. Load Resistance Input t off t on t pdoff t pdon Output td tf ts tr 10 % 10 % 50 % 50 % 90 % 90 % isfh6916_12 Fig. 11 - Switching Time Measurement Rev. 2.1, 12-Apr-13 Document Number: 83687 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH6916 www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters R0.25 4.83 4.32 0.36 1.27 0.91 5.08 7.37 11.02 10.52 5.59 5.08 0.43 0.33 0.87 0.61 IS O method A 40° 10° 0.20 0.10 2.03 1.91 0.00 0.13 0.46 0.36 i178043-2 1.14 5.08 5.59 7.11 6.60 1.40 1.14 PACKAGE MARKING SFH6916 V YWW U 68 Rev. 2.1, 12-Apr-13 Document Number: 83687 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000