RadiPac 2014-06 EN

EC centrifugal fans – RadiPac
version 2014-06
RadiPac: Now even more efficient
The line of radial plug fans with GreenTech EC motor technology already
All RadiPacs listed in the catalogue exceed the tougher new minimum
established in the market has been expanded further. Our new product
efficiency requirements of the ErP Directive for Fans, effective as of 2015.
line: RadiPac.
The motor efficiency of the GreenTech EC motors is significantly above
those specified in efficiency class IE4. And this is achieved without even
RadiPac is to denote medium pressure radial fans and is meant to be an
having to resort to any of the rare earth magnets, the procurement of
independent line positioned to complement the low pressure line RadiCal.
which we are critical of.
The “Pac” in RadiPac is short for “packaged”, as all required functions are
packed into one fan and are on board.
The welded impellers with their 7 backward curved blades are deliberate-
The RadiPac line is available in drive capacities of up to 12 kW and sizes
and maximises durability with high circumferential velocity. The position of
250mm to 1250mm in outer diameter. As a standard, all fans with their
the impellers on the EC external-rotor motors has been optimised in terms
rated input exceeding 500 Watts can be controlled by MODBUS and
of aerodynamic and installation requirements.
ly made of aluminium as this minimises the bearing load of the motors
0-10V.
With the new release of our selection programme “Product selector”, the
What is new is their mechanical design. All sizes can now also be ordered
complete RadiPac line is available. This tool allows fans to be selected
as versions which can be directly mounted on the floor. As of size 400, the
according to the specified duty points, and this selection to be compared
mechanical structure is executed in the form of a cube. The proven sup-
and documented. Using a DLL file, the RadiPacs can be integrated in your
port bracket is available up to size 560.
specific programme for fan selection.
All this allows them to be used in a wide variety of applications, going
beyond the mere ventilation and air-conditioning industry. Generally, the
RadiPacs are intended for use without scroll housing.
2
Table of contents
RadiPac: Everything packed in compact form
2
GreenTech: The Green Company
4
Product overview: RadiPac
6
Overview of characteristic curves - RadiPac
8
Text for tenders
10
Size 250 - Z50
12
Size 280 - 450 (compact design)
78
Accessories
82
Electrical connections
88
Technical parameters & scope
94
ebm-papst representatives & subsidiaries
98
3
Sustainability is at the centre of our
thoughts and actions. Out of conviction!
Eco-friendliness and sustainability have always been at the core of our thoughts and actions. For decades, we have worked according to the
simple but strict creed of our co-founder Gerhard Sturm: “Each new product we develop has to be better than the last one in terms of economy
and ecology.” GreenTech is the ultimate expression of our corporate philosophy.
GreenTech is pro-active development.
GreenTech is eco-friendly production.
Even in the design phase, the materials and processes we use are op-
GreenTech also stands for maximum energy efficiency in our pro-
timised for the greatest possible eco-friendliness, energy balance and
duction processes. There, the intelligent use of industrial waste heat
– wherever possible – recyclability. We continually improve the materi-
and groundwater cooling, photovoltaics and, of course, our own
al and performance of our products, as well as the flow and noise cha-
cooling and ventilation technology are of the utmost importance. Our
racteristics. At the same time, we significantly reduce energy conump-
most modern plant, for instance, consumes 91% less energy than
tion. Close co-operation with universities and scientific institutes and
currently specified and required. In this way, our products contribute
the professorship we endow in the area of power engineering and re-
to protecting the environment, from their origin to their recyclable
generative energies allows us to profit from the latest research finings
packaging.
in these fields – and at the same time ensure highly qualified young
academics.
GreenTech
follows a firm
philosophy.
GreenTech is
pro-active
development.
GreenTech
pays off
for our
customers.
GreenTech is
eco-friendly
production.
GreenTech is
acknowledged
and certified.
4
GreenTech is acknowledged and certified.
Our customers profit from this every day.
Every step in our chain of production meets the stringent standards of
The heart of GreenTech is future-oriented EC technology from ebm-
environmental specialists and the public.
papst. The EC technology at the core of our most efficient motors
This supports our position as Germany‘s most sustainable company
and fans allows efficiency of up to 90%, saves energy at a very high
2013, as does the DEKRA Award 2012 we received in the category
level, significantly extends service life and makes our products
“Umwelt – Herausforderung Energiewende / Environment – Challen-
maintenance-free. These values pay off not only for the environ-
ge: Transition to more sustainable energy systems”, to name only a
ment, but every cent also pays off for the user! All ebm-papst pro-
few of a large number of examples. The environmental advantage gai-
ducts – even those for which GreenTech EC technology does not
ned in the performance of the products developed from our Green-
(yet) make sense from an application viewpoint – feature the grea-
Tech philosophy can also be measured in the fulfillment of the most
test possible connection of economy and ecology.
stringent energy and environmental standards. In many instances, our
products are already well below the thresholds energy legislation will
impose a few years from now – several times over.
5
Product overview: RadiPac
RadiPac: Overview of types
Baugröße
Size
Nominal voltage range
VAC
Max. input power
W
M3G 084-DF
1~ 200-277
450
R3G250-AT39-71
K3G250-AT39-72
M3G 084-FA
1~ 200-277
700
R3G250-AV29-B1
K3G250-AV29-B2
M3G 084-GF
3~ 380-480
820
R3G250-AY11-C1
K3G250-AY11-C2
M3G 084-FA
1~ 200-277
415
R3G280-AT04-71
K3G280-AT04-72
M3G 084-GF
1~ 200-277
715
R3G280-AU06-B1
K3G280-AU06-B2 M3G 084-GF
3~ 380-480
1000
R3G280-AU11-C1
K3G280-AU11-C2
M3G 112-EA
3~ 380-480
1000
R3G310-AX52-90
K3G310-AX52-90
M3G 112-EA
1~ 200-277
1270
R3G310-AX54-21
K3G310-AX54-22
M3G 112-GA
3~ 380-480
1650
R3G310-BB49-01
K3G310-BB49-02
M3G 112-IA
3~ 380-480
3240
R3G310-AZ88-01
K3G310-AZ88-02
M3G 112-EA
3~ 380-480
1000
R3G355-AX56-90
K3G355-AX56-90
M3G 112-GA
1~ 200-277
1400
R3G355-AY43-21
K3G355-AY43-22
M3G 112-GA
3~ 380-480
1700
R3G355-AY40-01
K3G355-AY40-02
M3G 112-IA
3~ 380-480
2250
R3G355-BC92-01
K3G355-BC92-02
M3G 112-IA
3~ 380-480
1850
R3G400-AY87-01
K3G400-AY87-02
M3G 150-FF
3~ 380-480
3000
R3G400-AQ23-01
K3G400-AQ23-01
M3G 150-FF
3~ 380-480
3380
R3G400-AQ23-68
K3G400-AQ23-68
M3G 112-IA
3~ 380-480
1650
R3G450-AY86-01
K3G450-AY86-02
M3G 150-FF
3~ 380-480
2640
R3G450-AQ25-68
K3G450-AQ25-68
M3G 150-IF
3~ 380-480
5250
R3G450-AZ24-68
K3G450-AZ24-68
M3G 150-FF
3~ 380-480
2825
R3G500-AP25-01
K3G500-AP25-01
M3G 150-FF
3~ 380-480
3540
R3G500-AP25-68
K3G500-AP25-68
M3G 150-IF
3~ 380-480
5400
R3G500-AQ31-68
K3G500-AQ31-68
M3G 150-IF
3~ 380-480
3530
R3G560-AP21-68
K3G560-AP21-68
M3G 150-NA
3~ 380-480
4600
R3G560-AQ08-68
K3G560-AQ08-68
M3G 150-NA
3~ 380-480
2900
R3G630-AP01-01
K3G630-AP01-01
M3G 200-HF
3~ 380-480
6750
---
---
M3G 200-QA
3~ 380-480
11000
---
---
M3G 150-NA
3~ 380-480
2800
R3G710-AP02-01
K3G710-AP02-01
M3G 200-LA
3~ 380-480
7860
---
---
M3G 200-QA
3~ 380-480
11800
---
---
M3G 200-QA
3~ 380-480
7530
---
---
M3G 200-QA
3~ 380-480
11600
---
---
M3G 200-QA
3~ 380-480
7520
---
---
M3G 200-QA
3~ 380-480
8700
---
---
M3G 200-QA
3~ 380-480
3560
---
---
Baugröße
Size
Motor
Nominal voltage range
VAC
Max. input power
W
Centrifugal fan
280
M3G 084-GF
3~ 380-480
985
R3G280-AJ14-C1
310
M3G 112-GA
3~ 380-480
1650
R3G310-BC38-01
355
M3G 112-GA
3~ 380-480
1730
R3G355-BD43-01
400
M3G 150-FF
3~ 380-480
2840
R3G400-AS23-01
450
M3G 150-FF
3~ 380-480
2380
R3G450-AS24-01
250
250
280
310
355
355
400
400
450
500
500
560
630
710
800
900
Z50
Centrifugal fan
Standard
RadiPac in compact design
6
Centrifugal module
with support bracket
Standard
Motor
Centrifugal module
with support bracket
Increased corrosion protection (1)
Centrifugal module
with support bracket
Hygiene devices (2)
Centrifugal module
with support- (3),
cube design (4)
K3G250-AT39-74
K3G250-AT39-56
K3G250-AT39-89 (3)
K3G250-AV29-B4
K3G250-AV29-B6
K3G250-AV29-B9 (3)
K3G250-AY11-C4
---
K3G250-AY11-C9 (3)
K3G280-AT04-74
K3G280-AT04-56
K3G280-AT04-89 (3)
K3G280-AU06-B4
K3G280-AU06-B6
K3G280-AU06-B3 (3)
K3G280-AU11-C4
K3G280-AU11-C6
K3G280-AU11-C9 (3)
K3G310-AX52-96 (3)
K3G310-AX52-91
K3G310-AX52-35
K3G310-AX54-52
---
K3G310-AX54-98 (3)
K3G310-BB49-32
---
K3G310-BB49-96 (3)
K3G310-AZ88-32
K3G310-AZ88-35
K3G310-AZ88-96 (3)
K3G355-AX56-91
---
K3G355-AX56-96 (3)
K3G355-AY43-52
---
K3G355-AY43-98 (3)
K3G355-AY40-32
K3G355-AY40-35
K3G355-AY40-96 (3)
K3G355-BC92-32
---
K3G355-BC92-96 (3)
K3G400-AY87-32
---
K3G400-AY87-96 (3)
K3G400-AQ23-31
K3G400-AQ23-35
K3G400-AQ23-02 (4)
---
---
---
K3G450-AY86-32
---
K3G450-AY86-96 (4)
---
---
---
---
---
---
K3G500-AP25-31
---
K3G500-AP25-02 (4)
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
K3G630-AR02-01 (4)
---
---
K3G630-AS05-01 (4)
---
---
---
---
---
K3G710-AR03-01 (4)
---
---
K3G710-AS06-01 (4)
---
---
K3G800-AR08-01 (4)
---
---
K3G800-AS07-01 (4)
---
---
K3G900-AR10-01 (4)
---
---
K3G900-AS08-01 (4)
---
---
K3GZ50-AQ11-01 (4)
Legend:
(1) Increased
corrosion protection:
- Support bracket coated in black
- Support plate and impeller coated in black
- Motor coated in black
(2) Design
of hygiene devices:
- Support bracket coated in black
- Support plate and impeller coated in white
- Motor coated in black
- Mounting elements made of stainless steel
For technical data and dimensions – see
standard type.
(3) Support
(4) Cube
design
design
7
Pa
Overview of characteristic curves: RadiPac
3000
Ø 310
2000
Ø 450
Ø 500
Ø 630
Ø 710
Ø 800
Ø 400
Ø 355
Ø 900
Ø 560
Ø 250
Ø 280
1000
900
800
700
600
500
400
Ø Z50
300
pfs
200
100
500
qV
8
1000
2000
3000
4000
5000
10000
20000
30000
40000 50000
m3/h
RadiPac in the Product Selector
Additionaly, and for selecting the correct fan, you can take advan-
Additionally, the life cycle costs for the selected fans can be calculated.
tage of the ebm-papst software "Product Selector" with integrated
You can make your selection based on the operating point or on the type
“Black-Box" module for integration in system configuration pro-
designation.
grammes on the customer side.
The data sheets, which can be created in PDF format, show not only the
The new selection program gives you the ability to select plug fans based
nominal data of the fan, but also the performance data in the specified
on the operating point. If multiple fans are in the specified power range,
operating point with the inlet and outlet side sound power levels across
the aerodynamic and acoustic data displayed can be used to select and
the octave band.
document the most suitable fan.
For more detailed information, simply ask your ebm-papst contact!
9
EC centrifugal fans – RadiPac
K3G 250 to K3G 560
Text for tender for radial fan modules:
Protective features:
Single inlet; direct drive; high-performance radial impeller with circumfe-
- Alarm relay with zero-potential change-over contacts
rential diffuser mounted on an electronically commutated external-rotor
motor with integrated control electronics; radial impeller made of alumi-
(250 V AC/2 A, cos ϕ = 1)
- Locked-rotor protection
nium with backward curved, continuously welded blades; aerodynamical-
- Phase failure detection
ly optimised inlet nozzle with bleeder connection for pressure relief made
- Soft start of motors
of zinc-coated sheet steel; complete unit statically and dynamically balan-
- Mains under-voltage detection
ced in two planes as per DIN / ISO 1940 to balancing grade G 6.3; EC
- Over-temperature protection of electronics and motor
external-rotor motor, efficiency class IE4 without “rare earth” magnets
- Short-circuit protection
being used, with maintenance-free ball bearings and permanent lubrication; nominal lifetime 40,000 operating hours; wide voltage input 1~200-
Technical data:
277 V, 50/60 respectively 3~380-480 V, 50/60 Hz; unit can be operated
- Air flow
qV
on all standard Electricity Board networks at identical air performance;
- Static pressure
pfs = __________Pa
optimised motor technology; soft start; integrated current limitation; con-
- Nominal voltage range
U
=
V
nection via brought-out variable cable connector (motor size 084) or easy-
- Frequency
f
=
Hz
to-mount and robust integrated terminal box made of aluminium with
- Fan speed
n
= __________rpm
spring-loaded terminals (motor sizes 112, 150 and 200); extremely com-
- Input power
Ped = __________kW
pact electronics; with adjustable PID controller (motor sizes 112, 150 and
- Current draw
I
= __________A
200); meets all relevant EMC directives and all requirements as to circuit
- Noise level
Lp
= __________dBA
feedbacks; requires no complicated installation with shielded cables; very
- Perm. ambient temperature
T
low-noise commutation logic; 100 % speed-controllable. Motors with an
- Mass Fan
output of 750W or higher have an RS485/MODBUS RTU interface. Any
potentially necessary constructional measures for structure-borne sound
insulation have to be provided by customers.
Optional: Modules with increased corrosion protection.
For technical data, dimensions and connections – see data sheet.
10
Fan type: K3G .....
Product: ebm-papst
= __________m3/h
=
°C
= __________kg
EC centrifugal fans – RadiPac
K3G 400 to K3G Z50
Text for tender for radial fan modules:
Protective features:
Single inlet; direct drive; high-performance radial impeller with circumfe-
- Alarm relay with zero-potential change-over contacts
rential diffuser mounted on an electronically commutated external-rotor
(250 V AC/2 A, cos ϕ = 1)
motor with integrated control electronics; radial impeller made of alumi-
- Locked-rotor protection
nium with backward curved, continuously welded blades; aerodynamical-
- Phase failure detection
ly optimised inlet nozzle made of zinc-coated sheet steel; complete unit
- Soft start of motors
statically and dynamically balanced in two planes as per DIN / ISO 1940
- Mains under-voltage detection
to balancing grade G 6.3; EC external-rotor motor, efficiency class IE4
- Over-temperature protection of electronics and motor
without “rare earth” magnets being used, with maintenance-free ball bea-
- Short-circuit protection
rings and permanent lubrication; nominal lifetime 40,000 operating hours;
wide voltage input 3~380-480 V, 50/60 Hz; unit can be operated on all
Technische Daten:
standard Electricity Board networks at identical air performance; optimi-
- Air flow
qV
sed motor technology; soft start; integrated current limitation; connection
- Static pressure
pfs = __________Pa
via easy-to-mount and robust integrated terminal box made of aluminium
- Nominal voltage range
U
=
V
with spring-loaded terminals; extremely compact electronics; with adju-
- Frequency
f
=
Hz
stable PID controller; meets all relevant EMC directives and all require-
- Fan speed
n
= __________rpm
ments as to circuit feedbacks; requires no complicated installation with
- Input power
Ped = __________kW
shielded cables; very low-noise commutation logic; 100 % speed-control-
- Current draw
I
= __________A
lable. All fans have an RS485/MODBUS RTU interface. Any potentially
- Noise level
Lp
= __________dBA
necessary constructional measures for structure-borne sound insulation
- Perm. ambient temerature
T
=
have to be provided by customers.
- Mass Fan
= __________kg
- Direction of rotation Impeller
= Clockwise, seen
on rotor
For technical data, dimensions and connections – see data sheet.
= __________m3/h
°C
Fan type: K3G .....
Product: ebm-papst
11
EC centrifugal fans – RadiPac
backward curved, Ø 250
Nominal
voltage range
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
VAC
Hz
rpm
W
A
°C
1~ 200-277
50/60
3000
448
2,80
-25..+40
p. 88 / K1)
B
1~ 200-277
50/60
3450
750
3,30
-25..+40
p. 91 / L7)
C
3~ 380-480
50/60
3580
790
1,50
-25..+60
p. 93 / P2)
Curve
Nominal data
Type
Motor
*3G 250
M3G 084-DF
A
*3G 250
M3G 084-FA
*3G 250
M3G 084-GF
Curves
Pa
(1) Nominal data in operating point with maximum load and 230 or 400 VAC
in H2O
subject to alterations
Technical features
and electr. connection
– Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Sheet aluminium
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
C
ηmax.
=
4,8
1200
3
4,0
1000
4
800
3,2
3
A
4
600
2,4
3
3
400
1,6
2
2
pfs
200
0,8
2
0
qV
400
400
800
800
1200
1
1600
1200
1600
2000
2400
2800
1
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
12
Ped
W
I
A
LWA
dB(A)
A
1
3175
380
2,48
84
A
2
3045
436
2,72
80
A
3
3000
448
2,80
76
A
4
3020
436
2,72
80
B
1
3450
581
2,58
85
B
2
3450
673
2,98
82
B
3
3450
750
3,30
79
B
4
3450
691
3,07
86
C
1
3655
642
1,25
87
C
2
3605
735
1,40
84
C
3
3580
790
1,50
80
C
4
3635
709
1,38
88
4
B
n
rpm
Mass of centrifugal
module with support
design
Mass of centrifugal
module with support
bracket
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 88 ff.
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Cable exit: A Variable
– Terminal box design: B C Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: VDE, UL, CSA, CCC, GOST are applied for
Centrifugal fan
kg
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
Centrifugal module
w. supp. bracket (2)
kg
Centrifugal module
w. support design
kg
R3G 250-AT39 -71
4,4
25075-2-4013
K3G 250-AT39 -72
8,4
K3G 250-AT39 -74
8,4
K3G 250-AT39 -89
10,4
R3G 250-AV29 -B1
5,6
25075-2-4013
K3G 250-AV29 -B2
10,1
K3G 250-AV29 -B4
10,1
K3G 250-AV29 -B9
12,1
R3G 250-AY11 -C1
6,7
25075-2-4013
K3G 250-AY11 -C2
11,1
K3G 250-AY11 -C4
11,1
K3G 250-AY11 -C9
13,1
(2) Centrifugal module with higher protection against corrosion
Drawings
p. 14 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 88 ff.
13
EC centrifugal fans – RadiPac
backward curved, Ø 250
R3G 250-AT39-71 (Centrifugal fan)
4x90°
201,5±3
153,5 ±2
30°
45°
43
4xØ4.5
48
Depth of screw max. 10 mm
80
112
Core-end sleeves
4x90°
600+20
85
Ø260
Ø290
Ø166.2
Ø178
Ø150±0.25
Ø100
Ø176 +1
Ø284
M6
6
1,5
Ø164±0.35
Accessory part: Inlet nozzle 25075-2-4013
not included in the standard scope of delivery (k-value: 70)
Connection line AWG 22,
3x crimped core-end sleeves
Connection line AWG 18,
5x crimped core-end sleeves
K3G 250-AT39-72 / -74 (Centrifugal module with support bracket)
235±3
187±1
o400
o298
2
4xØ11
10
85 60
± 0
+2
0
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o350
Pressure tap (k-value: 70)
K3G 250-AT39-89 (Centrifugal module with support design)
235 ±3
187 ±2
400
350
298
2
404
4xØ11
Pressure tap
(k-value: 70)
20
0+
60
4
10
±
85
8
110
M4
15
32.5
160
14
280
325
351
Ø9
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
R3G 250-AV29-B1 (Centrifugal fan)
223.9±3
167.4±2
4x Ø4.5
56.5
5x
72
°
43
Depth of screw
max. 16 mm
Cable gland M16x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 2.5±0.4 Nm
Ø260
Ø290
Ø166.2
Ø176 +1
Ø284
Ø197
Ø165±0.25
Ø130
M6 (5x)
1.5
Ø186±0,5
Tightening torque
3.5±0.5 Nm
80
112
6
Accessory part: Inlet nozzle 25075-2-4013
not included in the standard scope of delivery (k-value: 70)
K3G 250-AV29-B2 / -B4 (Centrifugal module with support bracket)
257.5±3
201±1
o400
o298
2
4xØ11
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o350
Pressure tap (k-value: 70)
K3G 250-AV29-B9 (Centrifugal module with support design)
257.5 ±3
201 ±1
400
350
298
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
4
404
4xØ11
2
Pressure tap
(k-value: 70)
125
M4
15
32.5
175
280
325
351
Ø9
15
EC centrifugal fans – RadiPac
backward curved, Ø 250
R3G 250-AY11-C1 (Centrifugal fan)
223.9±3
167.4±2
4x Ø4.5
56.5
5x
72
43
°
Depth of screw
max. 16 mm
Cable gland M16x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 2.5±0.4 Nm
Ø260
Ø290
Ø166.2
Ø176 +1
Ø284
Ø197
Ø165±0.25
Ø130
M6 (5x)
1.5
Ø186±0,5
Tightening torque
3.5±0.5 Nm
80
112
6
Accessory part: Inlet nozzle 25075-2-4013
not included in the standard scope of delivery (k-value: 70)
K3G 250-AY11-C2 / -C4 (Centrifugal module with support bracket)
257.5±3
201±1
o400
o298
2
4xØ11
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o350
Pressure tap (k-value: 70)
K3G 250-AY11-C9
(Centrifugal module with support design)
257.5 ±3
201 ±1
400
350
298
4
404
4xØ11
2
Pressure tap
(k-value: 70)
16
125
M4
15
32.5
175
280
325
351
Ø9
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
17
EC centrifugal fans – RadiPac
backward curved, Ø 280
Nominal
voltage range
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
VAC
Hz
rpm
W
A
°C
1~ 200-277
50/60
2400
415
2,70
-25..+40
p. 88 / K1)
B
1~ 200-277
50/60
2800
715
3,10
-25..+40
p. 91 / L7)
C
3~ 380-480
50/60
3100
1000
1,60
-25..+60
p. 93 / P2)
Curve
Nominal data
Type
Motor
*3G 280
M3G 084-FA
A
*3G 280
M3G 084-GF
*3G 280
M3G 084-GF
Curves
Pa
(1) Nominal data in operating point with maximum load and 230 or 400 VAC
in H2O
subject to alterations
3
C
ηmax.
=
4
4,0
1000
B
4
3,2
800
3
A
3
600
2,4
4
400
1,6
3
2
2
0,8
2
200
pfs
1
0
qV
500
500
1000
1000
1500
1500
2000
2500
1
2000
3000
3500
1
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
18
Technical features
and electr. connection
– Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Sheet aluminium
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
n
rpm
Ped
W
I
A
LWA
dB(A)
A
1
2530
335
2,19
80
A
2
2415
392
2,57
75
A
3
2400
415
2,70
71
A
4
2405
405
2,66
75
B
1
2800
479
2,11
83
B
2
2800
655
2,88
79
B
3
2800
715
3,10
76
B
4
2800
650
2,85
82
C
1
3100
645
1,04
86
C
2
3100
852
1,35
83
C
3
3100
1000
1,60
80
C
4
3100
921
1,46
83
Mass of centrifugal
module with support
design
Mass of centrifugal
module with support
bracket
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 88 ff.
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Cable exit: A Variable
– Terminal box design: B C Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: VDE, UL, CSA, CCC, GOST are applied for
Centrifugal fan
kg
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
Centrifugal module
w. supp. bracket (2)
kg
Centrifugal module
w. support design
kg
R3G 280-AT04 -71
5,4
28075-2-4013
K3G 280-AT04 -72
9,7
K3G 280-AT04 -74
9,7
K3G 280-AT04 -89
11,7
R3G 280-AU06 -B1
6,8
28075-2-4013
K3G 280-AU06 -B2
11,5
K3G 280-AU06 -B4
11,5
K3G 280-AU06 -B3
13,5
R3G 280-AU11 -C1
7,1
28075-2-4013
K3G 280-AU11 -C2
11,7
K3G 280-AU11 -C4
11,7
K3G 280-AU11 -C9
13,7
(2) Centrifugal module with higher protection against corrosion
Drawings
p. 20 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 88 ff.
19
EC centrifugal fans – RadiPac
backward curved, Ø 280
R3G 280-AT04-71 (Centrifugal fan)
30°
53
4xØ4.5
48
4x90°
227±3
179 ±2
Depth of screw max. 10 mm
45°
90
132
Core-end sleeves
4x90°
600+20
85
Ø280
Ø325
Ø187.2
Ø178
Ø150±0.25
Ø100
Ø197.4 +1.8
Ø319
M6
10
1.5
Ø164±0.35
Accessory part: Inlet nozzle 28075-2-4013
not included in the standard scope of delivery (k-value: 93)
Connection line AWG 18,
5x crimped core-end sleeves
Connection line AWG 22,
3x crimped core-end
sleeves
K3G 280-AT04-72 / -74 (Centrifugal module with support bracket)
268±3
218±1
o400±1.2
o298
2
4xØ11
10
6
85 00+
±
2
0
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o350
Pressure tap (k-value: 93)
K3G 280-AT04-89
(Centrifugal module with support design)
268 ±3
218 ±1
400
350
298
2
404
4xØ11
Pressure tap
(k-value: 93)
20
0+
60
4
10
±
85
8
140
M4
15
32.5
190
20
280
325
351
Ø9
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
R3G 280-AU06-B1 (Centrifugal fan)
252.4±3
196±2
4x Ø4.5
56.5
5x
Depth of screw
max. 16 mm
72
°
53
Cable gland M16x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 2.5±0.4 Nm
Ø280
Ø325
Ø187.2
Ø197
Ø165±0.25
Ø130
Ø197.4 +1.8
Ø319
M6 (5x)
Tightening torque
3.5±0.5 Nm
Ø186±0,5
1.5
90
132
Accessory part: Inlet nozzle 28075-2-4013
not included in the standard scope of delivery (k-value: 93)
10
K3G 280-AU06-B2 / -B4 (Centrifugal module with support bracket)
291.5±3
235±1
o400
o298
2
4xØ11
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o350
Pressure tap (k-value: 93)
(Centrifugal module with support design)
291.5 ±3
235 ±1
400
350
298
404
4xØ11
2
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
4
K3G 280-AU06-B3
Pressure tap
(k-value: 93)
155
M4
15
32.5
205
280
325
351
Ø9
21
EC centrifugal fans – RadiPac
backward curved, Ø 280
R3G 280-AU11-C1 (Centrifugal fan)
252.4±3
196±2
4x Ø4.5
56.5
Depth of screw
max. 16 mm
5x
72
°
53
Ø280
Ø325
Ø187.2
Ø197
Ø165±0.25
Ø130
Ø197.4 +1.8
Ø319
M6 (5x)
Tightening torque
3.5±0.5 Nm
Ø186±0,5
1.5
Cable gland M16x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 2.5±0.4 Nm
90
132
Accessory part: Inlet nozzle 28075-2-4013
not included in the standard scope of delivery (k-value: 93)
10
K3G 280-AU11-C2 / -C4 (Centrifugal module with support bracket)
291.5±3
235±1
o400
o298
2
4xØ11
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o350
Pressure tap
(k-value: 93)
K3G 280-AU11-C9
(Centrifugal module with support design)
291.5 ±3
235 ±1
400
350
298
4
404
4xØ11
2
Pressure tap
(k-value: 93)
155
32.5
205
22
M4
15
280
325
351
Ø9
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
23
EC centrifugal fans – RadiPac
backward curved, Ø 310
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
VAC
Hz
rpm
W
A
°C
3~ 380-480
50/60
2580
1000
1,63
-25..+55
p. 90 / L6)
B
1~ 200-277
50/60
2850
1270
5,60
-25..+60
p. 92 / L9)
M3G 112-GA
C
3~ 380-480
50/60
3140
1650
2,50
-25..+60
p. 89 / M3)
M3G 112-IA
D
3~ 380-480
50/60
4100
3240
4,90
-25..+40
p. 89 / M3)
Curve
Nominal
voltage range
Technical features
and electr. connection
– Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Sheet aluminium
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Nominal data
Type
Motor
*3G 310
M3G 112-EA
A
*3G 310
M3G 112-EA
*3G 310
*3G 310
Curves
Pa
(1) Nominal data in operating point with maximum load and 230 or 400 VAC
in H2O
subject to alterations
1600
ηmax.
=
8,0
6,4
2000
3
4
D
4,8
1200
4
A
3
800
3,2
4
2
3
2580
669
1,17
88
2
2580
862
1,46
81
A
3
2580
1000
1,63
77
A
4
2580
907
1,53
79
B
1
2930
946
4,14
88
B
2
2895
1147
5,01
83
B
3
2850
1270
5,60
79
B
4
2850
1237
5,41
83
C
1
3140
1158
1,79
90
C
2
3140
1440
2,21
86
C
3
3140
1650
2,50
83
C
4
3140
1559
2,39
87
1,6
2
D
1
4100
2244
3,35
99
D
2
4100
2767
4,12
94
D
3
4100
3240
4,90
91
D
4
4100
3018
4,49
95
2
2
pfs
1
0
qV
500
1000
1000
2000
1500
2000
3000
2500
4000
1
1
3000
5000
1
3500
cfm
6000
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
24
LWA
dB(A)
1
3
400
I
A
A
4
B
Ped
W
A
3
C
n
rpm
Mass of centrifugal
module with support
design
Mass of centrifugal
module with support
bracket
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 89 ff.
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Terminal box design: Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: B GOST
A C D VDE, GOST
Centrifugal fan
kg
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
Centrifugal module
w. supp. bracket (2)
kg
Centrifugal module
w. support design
kg
R3G 310-AX52 -90
8,8
31575-2-4013
K3G 310-AX52 -90
16,7
K3G 310-AX52 -91
16,7
K3G 310-AX52 -96
19,0
R3G 310-AX54 -21
11,0
31575-2-4013
K3G 310-AX54 -22
19,4
K3G 310-AX54 -52
19,4
K3G 310-AX54 -98
22,2
R3G 310-BB49 -01
12,6
31575-2-4013
K3G 310-BB49 -02
21,0
K3G 310-BB49 -32
21,0
K3G 310-BB49 -96
24,1
R3G 310-AZ88 -01
15,0
31575-2-4013
K3G 310-AZ88 -02
24,2
K3G 310-AZ88 -32
24,2
K3G 310-AZ88 -96
26,2
(2) Centrifugal module with higher protection against corrosion
Drawings
p. 26 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 89 ff.
25
EC centrifugal fans – RadiPac
backward curved, Ø 310
R3G 310-AX52-90 (Centrifugal fan)
253,7±3
197,2±2
4xØ4,5
56,5
5xM6
55
Depth of screw
max. 16 mm
°
72
Cable gland
M16x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 2.5±0.4 Nm
Ø325
Ø350
Ø222
Ø360
Ø211,7
5x
Ø165
Ø186±0,5
100
147
10
Tightening torque
3.5±0.5 Nm
Accessory part: Inlet nozzle 31575-2-4013
not included in the standard scope of delivery (k-value: 116)
K3G 310-AX52-90 / -91 (Centrifugal module with support bracket)
294±3
237.5±2.5
o500
o372
15
4xØ11
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
M16x1.5(3x)
o450
Pressure tap (k-value: 116)
K3G 310-AX52-96
(Centrifugal module with support design)
500
450
372
15
4xØ11
294 ±3
237.5±2.5
4.3
Pressure tap
(k-value: 116)
150
200
26
15
M6
32.5
350
395
422
Ø9
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
R3G 310-AX54-21 (Centrifugal fan)
4xØ4.5
72
269.2 ±3
197.2 ±2
Accessory part: Inlet nozzle 31575-2-4013
not included in the standard scope of delivery (k-value: 116)
55
Depth of screw max. 20 mm
6xM10
6x6
Ø325
Ø350
Ø 222
Ø 360
Ø211.7
0°
Cable gland
M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø 232
100
147
Tightening torque
3.5±0.5 Nm
Ø 252±0.5
10
K3G 310-AX54-22 / -52 (Centrifugal module with support bracket)
309.5±3
237.5±2,5
o500
o375
15
Ø11 (4x)
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
M
o450
Pressure tap (k-value: 116)
K3G 310-AX54-98
)
x
5(3
1.
20x
(Centrifugal module with support design)
500
450
375
15
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
4.3
4xØ11
309.5 ±3
237.5 ±2.5
Pressure tap
(k-value: 116)
150
200
15
M6
32.5
350
395
422
Ø9
27
EC centrifugal fans – RadiPac
backward curved, Ø 310
R3G 310-BB49-01 (Centrifugal fan)
289.2 ±3
217.2 ±2
4xØ4.5
72
Accessory part: Inlet nozzle 31575-2-4013
not included in the standard scope of delivery (k-value: 116)
55
Depth of screw
max. 20 mm
6xM10
6x6
Ø325
Ø350
Ø 222
Ø 360
Ø211.7
0°
Cable gland
M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø 232
100
147
Ø 252±0.5
10
Tightening torque
3.5±0.5 Nm
K3G 310-BB49-02 / -32 (Centrifugal module with support bracket)
317.5±3
257.5±2
o500
o375
15
Ø11 (4x)
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
.5
0x1
M2
o450
Pressure tap (k-value: 116)
K3G 310-BB49-96
)
(3x
(Centrifugal module with support design)
500
450
375
15
4xØ11
317.5 ±3
257.5 ±2.5
4.3
Pressure tap
(k-value: 116)
170
220
28
15
M6
32.5
350
395
422
Ø9
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
R3G 310-AZ88-01 (Centrifugal fan)
289.2 ±3
217.2 ±2
Accessory part: Inlet nozzle 31575-2-4013
not included in the standard scope of delivery (k-value: 116)
4xØ4.5
72
55
Depth of screw
max. 20 mm
6xM10
0
6x6
Ø325
Ø350
Ø 222
Ø 360
Ø211.7
°
Cable gland
M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø 232
80
127
Tightening torque
3.5±0.5 Nm
Ø 252±0.5
10
K3G 310-AZ88-02 / -32 (Centrifugal module with support bracket)
329.5±3
257.5±2.5
o500
o375
15
Ø11 (4x)
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
.5
0x1
M2
o450
Pressure tap (k-value: 116)
(Centrifugal module with support design)
500
450
375
15
4xØ11
329.5 ±3
257.5 ±2.5
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
4.3
K3G 310-AZ88-96
)
(3x
Pressure tap
(k-value: 116)
170
220
15
M6
32.5
350
395
422
Ø9
29
EC centrifugal fans – RadiPac
backward curved, Ø 355
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
VAC
Hz
rpm
W
A
°C
3~ 380-480
50/60
2140
1000
1,65
-25..+60
p. 90 / L6)
B
1~ 200-277
50/60
2450
1400
6,00
-25..+50
p. 92 / L9)
M3G 112-GA
C
3~ 380-480
50/60
2600
1700
2,60
-25..+40
p. 89 / M3)
M3G 112-IA
D
3~ 380-480
50/60
2800
2250
3,50
-25..+55
p. 89 / M3)
Curve
Nominal
voltage range
Technical features
and electr. connection
– Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Sheet aluminium
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Nominal data
Type
Motor
*3G 355
M3G 112-EA
A
*3G 355
M3G 112-GA
*3G 355
*3G 355
Curves
Pa
(1) Nominal data in operating point with maximum load and 230 or 400 VAC
1400
5,6 in H2O
subject to alterations
D
3
ηmax.
=
n
rpm
Ped
W
I
A
LWA
dB(A)
4
4,8
1200
A
1
2140
656
1,14
87
A
2
2140
893
1,50
77
A
3
2140
1000
1,65
75
A
4
2140
918
1,54
78
B
1
2450
998
4,33
86
B
2
2440
1232
5,35
82
B
3
2450
1400
6,00
79
B
4
2410
1344
5,94
82
C
1
2600
1140
1,74
92
C
2
2600
1510
2,30
83
C
3
2600
1700
2,60
79
C
4
2600
1594
2,42
83
D
1
2800
1463
2,33
90
D
2
2800
1916
2,99
86
D
3
2800
2250
3,50
85
D
4
2800
2134
3,29
88
C
4
3
4,0
1000
B
4
3
800
3,2
A
4
3
600
2,4
3
2
pfs
200
2
2
0,8
400
1,6
2
0
qV
500
1000
1000
2000
1500
2000
3000
2500
4000
1
3000
5000
1
3500
6000
1
4000
cfm
7000 m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
30
Mass of centrifugal
module with support
design
Mass of centrifugal
module with support
bracket
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 89 ff.
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Terminal box design: Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: B GOST
A C D VDE, GOST
Centrifugal fan
kg
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
Centrifugal module
w. supp. bracket (2)
kg
Centrifugal module
w. support design
kg
R3G 355-AX56 -90
9,4
35675-2-4013
K3G 355-AX56 -90
17,4
K3G 355-AX56 -91
17,4
K3G 355-AX56 -96
19,4
R3G 355-AY43 -21
14,0
35675-2-4013
K3G 355-AY43 -22
22,4
K3G 355-AY43 -52
22,4
K3G 355-AY43 -98
25,5
R3G 355-AY40 -01
13,1
35675-2-4013
K3G 355-AY40 -02
23,4
K3G 355-AY40 -32
23,4
K3G 355-AY40 -96
25,0
R3G 355-BC92 -01
15,2
35675-2-4013
K3G 355-BC92 -02
25,8
K3G 355-BC92 -32
25,8
K3G 355-BC92 -96
27,8
(2) Centrifugal module with higher protection against corrosion
Drawings
p. 32 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 89 ff.
31
EC centrifugal fans – RadiPac
backward curved, Ø 355
R3G 355-AX56-90 (Centrifugal fan)
270.7±3
214.2±2
4xØ4.5
56.5
Depth of screw
max. 16 mm
5xM6
64.5
°
72
Cable gland
M16x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 2.5±0.4 Nm
Ø345
Ø370
Ø239
Ø405
Ø250.3
Ø404
5x
Ø165
Ø186±0.5
112
164
12
Tightening torque
3.5±0.5 Nm
Accessory part: Inlet nozzle 35675-2-4013
not included in the standard scope of delivery (k-value: 148)
K3G 355-AX56-90 / -91 (Centrifugal module with support bracket)
319.5±3
263±2.5
o500
o372
15
M16x1.5(3x)
4xØ11
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o450
Pressure tap (k-value: 148)
K3G 355-AX56-96
(Centrifugal module with support design)
500
450
372
15
4xØ11
319,5 ±3
263 ±2.5
4.3
Pressure tap
(k-value: 148)
175
225
32
15
M6
32.5
350
395
422
Ø9
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
R3G 355-AY43-21 (Centrifugal fan)
306.2 ±3
234.2±2
4xØ4.5
72
Accessory part: Inlet nozzle 35675-2-4013
not included in the standard scope of delivery (k-value: 148)
64.4
Depth of screw
max. 20 mm
6xM10
Ø345
Ø370
Ø 405
Ø 250.3
Ø 404
Ø239
0°
6x6
Ø 232
Cable gland
M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
112
164
Ø 252±0.5
12
Tightening torque
3.5±0.5 Nm
K3G 355-AY43-22 / -52 (Centrifugal module with support bracket)
354.5±3
282.5±2,5
o500
o375
15
Ø11 (4x)
Ø405
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
)
3x
5(
1.
20x
M
o450
Pressure tap (k-value: 148)
K3G 355-AY43-98
(Centrifugal module with support design)
500
450
375
15
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
4.3
4xØ11
354.5 ±3
282.5 ±2.5
Pressure tap
(k-value: 148)
195
245
15
M6
32.5
350
395
422
Ø9
33
EC centrifugal fans – RadiPac
backward curved, Ø 355
R3G 355-AY40-01 (Centrifugal fan)
4xØ4.5
72
306.2±3
234.2±2
Accessory part: Inlet nozzle 35675-2-4013
not included in the standard scope of delivery (k-value: 148)
64.4
Depth of screw
max. 20 mm
6xM10
6x6
Ø345
Ø370
Ø 405
Ø 250.3
Ø 404
Ø239
0°
Cable gland
M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø 232
112
164
Ø 252±0.5
12
Tightening torque
3.5±0.5 Nm
K3G 355-AY40-02 / -32 (Centrifugal module with support bracket)
354.5±3
282.5±2.5
o500
o375
15
Ø11 (4x)
Ø405
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
3x)
5(
1.
20x
M
o450
Pressure tap (k-value: 148)
K3G 355-AY40-96
(Centrifugal module with support design)
500
450
375
15
4xØ11
343±3
282.5 ±2.5
4.3
Pressure tap
(k-value: 148)
195
245
34
15
M6
32.5
350
395
422
Ø9
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
R3G 355-BC92-01 (Centrifugal fan)
4xØ4.5
326.2±3
254.2±2
72
Accessory part: Inlet nozzle 35675-2-4013
not included in the standard scope of delivery (k-value: 148)
64.4
Depth of screw
max. 20 mm
6xM10
6x6
Ø345
Ø370
Ø 405
Ø 250.3
Ø 405
Ø239
0°
Ø 232
Cable gland
M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
112
164
Ø 252±0.5
12
Tightening torque
3.5±0.5 Nm
K3G 355-BC92-02 / -32 (Centrifugal module with support bracket)
374.5±3
302.5±2.5
o500
o375
15
Ø11 (4x)
Ø405
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
M
3x)
.5(
1
20x
o450
Pressure tap (k-value: 148)
K3G 355-BC92-96
(Centrifugal module with support design)
500
450
375
15
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
4.3
4xØ11
374.5 ±3
302.5 ±2.5
Pressure tap
(k-value: 148)
215
265
15
M6
32.5
350
395
422
Ø9
35
EC centrifugal fans – RadiPac
backward curved, Ø 400
Nominal
voltage range
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
VAC
Hz
rpm
W
A
°C
3~ 380-480
50/60
2180
1850
2,90
-25..+50
p. 89 / M3)
B
3~ 380-480
50/60
2550
3000
4,60
-25..+60
p. 89 / M3)
C
3~ 380-480
50/60
2680
3380
5,15
-25..+40
p. 89 / M3)
Curve
Nominal data
Type
Motor
*3G 400
M3G 112-IA
A
*3G 400
M3G 150-FF
*3G 400
M3G 150-FF
Curves
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
1600
in H2O
subject to alterations
Technical features
and electr. connection
– Material: Support bracket: Steel, coated in black; Support plate and inlet nozzle: Sheet
steel, galvanised; Cube design with inlet nozzle: Sheet steel, galvanised and
plastic-coated in light grey (RAL 7035)
Impeller: Sheet aluminium
Rotor: Coated in black; Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: A "B"; B C "F"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
3
4
n
rpm
ηmax.
=
Ped
W
I
A
LWA
dB(A)
5,6
C
1400
A
1
2180
1178
1,81
89
A
2
2180
1748
2,66
82
A
3
2180
1850
2,90
81
A
4
2180
1638
2,49
84
B
1
2550
1989
3,03
93
B
2
2550
2578
3,92
87
B
3
2550
3000
4,60
85
B
4
2550
2890
4,41
87
C
1
2680
2384
3,65
93
C
2
2680
3069
1,69
88
C
3
2680
3380
5,15
85
C
4
2680
3140
4,77
91
B
1200
4,8
4
3
3
1000
4,0
A
4
3,2
400
1,6
600
200
0,8
800
2,4
3
2
2
2
pfs
1
0
qV
1000
2000
3000
2000
4000
4000
6000
1
5000
8000
1
6000 cfm
10000
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
36
Centrifugal fan
kg
R3G 400-AY87 -01
15,6
Mass of centrifugal
module with supportcube design
Mass of centrifugal
module with support
bracket
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 89
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Terminal box design: Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: A VDE, GOST;
B UL, CSA, GOST;
C GOST
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
Centrifugal module
w. supp. bracket (2)
kg
Centrifugal module with
support-(3) cube design(4)
40075-2-4013
K3G 400-AY87 -02
26,0
K3G 400-AY87 -32
26,0
K3G 400-AY87 -96
(3)
28,0
K3G 400-AQ23 -02
(4)
47,0
R3G 400-AQ23 -01
21,7
40075-2-4013
K3G 400-AQ23 -01
32,3
K3G 400-AQ23 -31
32,3
R3G 400-AQ23 -68
21,7
40075-2-4013
K3G 400-AQ23 -68
32,3
---
---
---
kg
---
(2) Centrifugal module with higher protection against corrosion (3) Support design (4) Cube design
Drawings
p. 38 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 89 ff.
37
EC centrifugal fans – RadiPac
backward curved, Ø 400
R3G 400-AY87-01 (Centrifugal fan)
Accessory part: Inlet nozzle 40075-2-4013
not included in the standard scope of delivery (k-value: 188)
72
6xØ9
345 ±3
273 ±2
68
Depth of screw
max. 20 mm
6xM10
6x6
Ø390
Ø413
Ø 282
Ø 455
Ø270.9
0°
Cable gland
M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø 232
125
182
Tightening torque
3.5±0.5 Nm
Ø 252±0.5
9
K3G 400-AY87-02 / -32 (Centrifugal module with support bracket)
399±3
327±2.5
o500
o375
15
Ø11 (4x)
Ø455
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
.5
1
20x
M
)
(3x
o450
Pressure tap (k-value: 188)
K3G 400-AY87-96
(Centrifugal module with support design)
387±3
327±2.5
500
450
375
4xØ11
15
4.3
Pressure tap
(k-value: 188)
240
290
38
15
M6
32.5
350
395
422
Ø9
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
R3G 400-AQ23-01 (Centrifugal fan)
Accessory part: Inlet nozzle 40075-2-4013
not included in the standard scope of delivery (k-value: 188)
68
6xØ9
335.6 ±3
265.6 ±2
70
Depth of screw
max. 25 mm
6xM10
220.5±1
Ø390
Ø413
Ø270.9
Ø455
Ø282
Ø188
0°
6x6
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
9
125
182
Ø252±0,3
Ø275
Tightening torque
3.5±0.5 Nm
K3G 400-AQ23-01 / -31 (Centrifugal module with support bracket)
390±3
320±2
o500-1
o375
15
M
20
x
(3 1.5
x)
Ø11 (4x)
Ø455
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o450
Pressure tap (k-value: 188)
K3G 400-AQ23-02 (Centrifugal module with cube design)
Inlet nozzle with pressure tap
(k-value: 188)
431
323
15
4xØ9
*435
*93
*298
500
* Screw-on position for rubber mounting respectively spring elements; with horizontal shaft position, only direct installation on the floor possible and permitted.
39
EC centrifugal fans – RadiPac
backward curved, Ø 400
R3G 400-AQ23-68 (Centrifugal fan)
6xØ9
335.6 ±3
265.6 ±2
70
Accessory part: Inlet nozzle 40075-2-4013
not included in the standard scope of delivery (k-value: 188)
68
Depth of screw
max. 25 mm
6xM10
220.5±1
Ø390
Ø413
Ø270.9
Ø455
Ø282
Ø188
0°
6x6
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
9
125
182
Ø252±0,3
Ø275
Tightening torque
3.5±0.5 Nm
K3G 400-AQ23-68 (Centrifugal module with support bracket)
390±3
320±2
15
o500-1
o375
20
x
(3 1.5
x)
M
Ø11 (4x)
Ø455
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o450
Pressure tap (k-value: 188)
40
41
EC centrifugal fans – RadiPac
backward curved, Ø 450
Nominal
voltage range
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
VAC
Hz
rpm
W
A
°C
3~ 380-480
50/60
1750
1615
2,50
-25..+50
p. 89 / M3)
B
3~ 380-480
50/60
2040
2640
4,00
-25..+60
p. 89 / M3)
C
3~ 380-480
50/60
2750
5250
7,95
-25..+40
p. 89 / M3)
Curve
Nominal data
Type
Motor
*3G 450
M3G 112-IA
A
*3G 450
M3G 150-FF
*3G 450
M3G 150-IF
1600
1200
C
3
4
6,4
2000
n
rpm
ηmax.
=
3,2
3
2
4
3
2
2
1,6
400
pfs
1
0
qV
1000
2000
2000
4000
3000
4000
6000
5000
8000
1
6000
10000
1
7000
cfm
12000
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
42
LWA
dB(A)
1
1750
1036
1,61
87
2
1750
1457
2,25
80
A
3
1750
1615
2,50
77
A
4
1750
1524
2,33
80
B
1
2040
1795
2,73
92
B
2
2040
2309
3,45
86
B
3
2040
2640
4,00
82
B
4
2040
2401
3,58
87
C
1
2750
3356
5,11
101
C
2
2750
4565
6,91
94
C
3
2750
5250
7,95
90
C
4
2750
4642
7,03
97
B
A
I
A
A
4
800
Ped
W
A
3
4,8
Curves
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
8,0 in H2O
subject to alterations
Technical features
and electr. connection
– Material: Support bracket: Steel, coated in black; Support plate and inlet nozzle: Sheet
steel, galvanised; Cube design with inlet nozzle: Sheet steel, galvanised and
plastic-coated in light grey (RAL 7035)
Impeller: Sheet aluminium
Rotor: Coated in black; Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: A "B"; B C "F"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Mass of centrifugal
module with cube
design
Mass of centrifugal
module with support
bracket
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 89
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Terminal box design: Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: A VDE, GOST;
B C GOST
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
Centrifugal module
w. supp. bracket (2)
kg
Centrifugal module
with cube design
kg
16,4
45075-2-4013
K3G 450-AY86 -02
31,9
K3G 450-AY86 -32
31,9
K3G 450-AY86 -96
46,0
R3G 450-AQ25 -68
22,5
45075-2-4013
K3G 450-AQ25 -68
38,2
---
---
---
---
R3G 450-AZ24 -68
31,1
45075-2-4013
K3G 450-AZ24 -68
52,7
---
---
---
---
Centrifugal fan
kg
R3G 450-AY86 -01
(2) Centrifugal module with higher protection against corrosion
Drawings
p. 44 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 89 ff.
43
EC centrifugal fans – RadiPac
backward curved, Ø 450
R3G 450-AY86-01 (Centrifugal fan)
Accessory part: Inlet nozzle 45075-2-4013
not included in the standard scope of delivery (k-value: 240)
6xØ9
367 ±3
295 ±2
72
76
Depth of screw
max. 20 mm
6xM10
6x6
Ø430
Ø480
Ø 317
Ø 505
Ø303.4
0°
Cable gland
M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø 232
140
204
Tightening torque
3.5±0.5 Nm
Ø 252±0.5
9
K3G 450-AY86-02 / -32 (Centrifugal module with support bracket)
429±3
357±2.5
o630
o551
15
Ø11 (4x)
Ø505
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
3x)
5(
1.
20x
M
o580
Pressure tap (k-value: 240)
K3G 450-AY86-96
(Centrifugal module with cube design)
Inlet nozzle with pressure tap
(k-value: 240)
*565
463.5
356
15
*61.5
*361.5
4xØ9
630
* Screw-on position for rubber mounting respectively spring elements; with horizontal shaft position, only direct installation on the floor possible and permitted.
44
R3G 450-AQ25-68 (Centrifugal fan)
Accessory part: Inlet nozzle 45075-2-4013
not included in the standard scope of delivery (k-value: 240)
76
6xØ9
357 ±3
287.2 ±2
70
Depth of screw
max. 25 mm
6xM10
220.5±1
Ø430
Ø480
Ø505
Ø303.4
Ø317
Ø188
0°
6x6
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø252±0,3
Ø275
9
140
204
Tightening torque
3.5±0.5 Nm
K3G 450-AQ25-68 (Centrifugal module with support bracket)
419±3
349±2
15
o630-1
o551
Pressure tap (k-value: 240)
20
x1
(3 .5
x)
M
Ø11 (8x)
Ø566
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o580
45
EC centrifugal fans – RadiPac
backward curved, Ø 450
R3G 450-AZ24-68 (Centrifugal fan)
406.5±3
293.5±2
Accessory part: Inlet nozzle 45075-2-4013
not included in the standard scope of delivery (k-value: 240)
6xØ9
113
Depth of screw
max. 20 mm
76
6xM10
Ø430
Ø480
Ø303.4
Ø317
Ø505
Ø188
0°
6x6
Ø280-2
Cable gland
M20x1,5(2x)
Cable gland
M25x1,5(1x)
112
176
Ø304±0.5
9
K3G 450-AZ24-68 (Centrifugal module with support bracket)
15
o630-1
o520.5
Ø11(8x)
469±3
355.5±2
o580
Pressure tap (k-value: 240)
46
Tightening torque
3.5±0.5 Nm
Cable diameter
min. 9 mm,
max. 16 mm,
tightening torque
6±0.9 Nm
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
47
EC centrifugal fans – RadiPac
backward curved, Ø 500
Nominal
voltage range
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
VAC
Hz
rpm
W
A
°C
3~ 380-480
50/60
1780
2825
4,30
-25..+60
p. 89 / M3)
B
3~ 380-480
50/60
1910
3540
5,40
-25..+45
p. 89 / M3)
C
3~ 380-480
50/60
2200
5400
8,10
-25..+45
p. 89 / M3)
Curve
Nominal data
Type
Motor
*3G 500
M3G 150-FF
A
*3G 500
M3G 150-FF
*3G 500
M3G 150-IF
Curves
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
in H2O
subject to alterations
1400
4
C
4,8
B
1200
n
rpm
ηmax.
=
5,6
1600
6,4
3
3
800
4,0
2,4
1,6
200
0,8
2
400
2
pfs
1
0
qV
2000
2000
LWA
dB(A)
1
1780
1985
3,09
94
A
2
1780
2530
3,90
89
A
3
1780
2825
4,30
83
A
4
1780
2692
4,14
85
B
1
1910
2365
3,53
95
B
2
1910
3044
4,57
89
B
3
1910
3540
5,40
82
B
4
1910
3202
4,81
87
C
1
2200
3614
5,39
98
C
2
2200
4630
6,95
93
C
3
2200
5400
8,10
87
C
4
2200
4937
7,41
92
3
2
600
I
A
A
3
3,2
1000
Ped
W
4
A
4
4000
4000
6000
6000
8000
10000
12000
1
8000
1
14000
m3/h
cfm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
48
Technical features
and electr. connection
– Material: Support bracket: Steel, coated in black; Support plate and inlet nozzle: Sheet
steel, galvanised; Cube design with inlet nozzle: Sheet steel, galvanised and
plastic-coated in light grey (RAL 7035)
Impeller: Sheet aluminium
Rotor: Coated in black; Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "F"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Mass of centrifugal
module with cube
design
Mass of centrifugal
module with support
bracket
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 89
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Terminal box design: Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: A UL, CSA, GOST;
B C GOST
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
Centrifugal module
w. supp. bracket (2)
kg
Centrifugal module
with cube design
kg
24,6
64025-2-4013
K3G 500-AP25 -01
40,2
K3G 500-AP25 -31
40,2
K3G 500-AP25 -02
58,5
R3G 500-AP25 -68
24,6
64025-2-4013
K3G 500-AP25 -68
40,2
---
---
---
---
R3G 500-AQ31 -68
21,7
64025-2-4013
K3G 500-AQ31 -68
32,3
---
---
---
---
Centrifugal fan
kg
R3G 500-AP25 -01
(2) Centrifugal module with higher protection against corrosion
Drawings
p. 50 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 89 ff.
49
EC centrifugal fans – RadiPac
backward curved, Ø 500
R3G 500-AP25-01 (Centrifugal fan)
Accessory part: Inlet nozzle 64025-2-4013
not included in the standard scope of delivery (k-value: 281)
75
6xØ9
373.5 ±3
303.5 ±2
70
Depth of screw
max. 25 mm
6xM10
220.5±1
6x6
Ø445
Ø470
Ø337.2
Ø566
Ø352.5
Ø188
0°
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø252±0,3
Ø275
12
150
220
Tightening torque
3.5±0.5 Nm
K3G 500-AP25-01 / -31 (Centrifugal module with support bracket)
431.5±3
361.5±2
o630-1
o551
15
M
20
x
(3 1.5
x)
Ø11 (8x)
Ø566
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o580
Pressure tap (k-value: 281)
K3G 500-AP25-02 (Centrifugal module with cube design)
Inlet nozzle with pressure tap
(k-value: 281)
*565
364
15
*96
473
4xØ9
*336
630
* Screw-on position for rubber mounting respectively spring elements; with horizontal shaft position, only direct installation on the floor possible and permitted.
50
R3G 500-AP25-68 (Centrifugal fan)
6xØ9
373.5 ±3
303.5 ±2
70
Accessory part: Inlet nozzle 64025-2-4013
not included in the standard scope of delivery (k-value: 281)
75
Depth of screw max. 25 mm
6xM10
220.5±1
6x6
Ø445
Ø470
Ø337.2
Ø566
Ø352.5
Ø188
0°
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø252±0,3
Ø275
12
150
220
Tightening torque 3.5±0.5 Nm
K3G 500-AP25-68 (Centrifugal module with support bracket)
431.5±3
361.5±2
o630-1
o551
15
20
x
(3 1.5
x)
M
Ø11 (8x)
Ø566
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o580
Pressure tap (k-value: 281)
51
EC centrifugal fans – RadiPac
backward curved, Ø 500
R3G 500-AQ31-68 (Centrifugal fan)
450.5±3
337.5±2
6xØ9
113
Accessory part: Inlet nozzle 64025-2-4013
not included in the standard scope of delivery (k-value: 281)
75
6xM10
298.5±1
Depth of screw
max. 20 mm
Ø445
Ø470
Ø337
Ø352.5
Ø566
Ø188
0°
6x6
Tightening torque
3.5±0.5 Nm
Ø280-2
Cable gland
M20x1,5(2x)
Cable gland
M25x1,5(1x)
150
220.5
12
Ø304±0.5
K3G 500-AQ31-68 (Centrifugal module with support bracket)
15
o630-1
o520.5
Ø11(8x)
510 ±3
396.5 ±2
o580
Pressure tap (k-value: 281)
52
Cable diameter
min. 9 mm,
max. 16 mm,
tightening torque
6±0.9 Nm
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
53
EC centrifugal fans – RadiPac
backward curved, Ø 560
Nominal
voltage range
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
VAC
Hz
rpm
W
A
°C
3~ 380-480
50/60
1610
3530
5,40
-25..+40
p. 89 / M3)
3~ 380-480
50/60
1750
4600
7,10
-25..+40
p. 89 / M3)
Curve
Nominal data
Type
Motor
*3G 560
M3G 150-IF
A
*3G 560
M3G 150-NA
B
Curves
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
1400
in H2O
subject to alterations
Technical features
and electr. connection
– Material: Support bracket: Steel, coated in black; Support plate and inlet nozzle: Sheet
steel, galvanised; Cube design with inlet nozzle: Sheet steel, galvanised and
plastic-coated in light grey (RAL 7035)
Impeller: Sheet aluminium
Rotor: Coated in black; Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "F"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
B
3
ηmax.
=
4,8
4,0
A
1000
3,2
2,4
3
600
1,6
2
400
0,8
2
200
pfs
1
0
qV
2000
4000
4000
6000
8000
12000
1
cfm
8000
16000
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
54
I
A
LWA
dB(A)
1
1610
2247
3,48
94
A
2
1610
2951
4,55
88
A
3
1610
3530
5,40
82
A
4
1610
3241
4,97
86
B
1
1750
2938
4,47
95
B
2
1750
3704
5,59
89
B
3
1750
4600
7,10
84
B
4
1750
4271
6,42
87
3
4
800
Ped
W
A
4
1200
n
rpm
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 89
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Terminal box design: Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: GOST
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
30,5
64030-2-4013
K3G 560-AP21 -68
56,1
40,0
64030-2-4013
K3G 560-AQ08 -68
69,7
Centrifugal fan
kg
R3G 560-AP21 -68
R3G 560-AQ08 -68
Drawings
p. 56 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 89 ff.
55
EC centrifugal fans – RadiPac
backward curved, Ø 560
R3G 560-AP21-68 (Centrifugal fan)
82
6xØ9
422 ±3
352 ±2
70
Accessory part: Inlet nozzle 64030-2-4013
not included in the standard scope of delivery (k-value: 348)
Depth of screw
max. 25 mm
6xM10
250.5±1
6x6
Ø490
Ø515
Ø385
Ø636
Ø395
Ø188
0°
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø252±0,3
Ø275
16
160
239
Tightening torque
3.5±0.5 Nm
K3G 560-AP21-68 (Centrifugal module with support bracket)
483±3
413±2
o800-1
o555
15
20
x
(3 1.5
x)
M
Ø11 (8x)
Ø566
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
o750
Pressure tap (k-value: 348)
56
R3G 560-AQ08-68 (Centrifugal fan)
Accessory part: Inlet nozzle 64030-2-4013
not included in the standard scope of delivery (k-value: 348)
6xØ9
505±3
392±2
113
Depth of screw
max. 20 mm
82
333±1
6xM10
Tightening torque
3.5±0.5 Nm
6x6
Ø490
Ø515
Ø385
Ø395
Ø636
Ø188
0°
Ø280-2
Cable gland
M20x1,5(2x)
Cable gland
M25x1,5(1x)
160
239
16
Ø304±0.5
Cable diameter
min. 9 mm,
max. 16 mm,
tightening torque
6±0.9 Nm
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
K3G 560-AQ08-68 (Centrifugal module with support bracket)
15
o800-1
o570
Ø11(8x)
566 ±3
453 ±2
o750
Pressure tap (k-value: 348)
57
EC centrifugal fans – RadiPac
backward curved, Ø 630
Cube design with inlet nozzle: Sheet steel, galvanised and
plastic-coated in light grey (RAL 7035)
Impeller: Sheet aluminium
Rotor: Coated in black; Electronics enclosure: Die-cast aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54 (acc. to EN 60529)
Insulation class: "F"
Mounting position: Shaft horizontal ( B C for floor installation only) or rotor on bottom;
rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
–
–
–
–
–
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
°C
kg
3~ 380-480
50/60
1130
2900
4,50
-25..+55
40
p. 89 / M3)
B
3~ 380-480
50/60
1500
6750
10,30
-25..+50
125
p. 89 / M3)
C
3~ 380-480
50/60
1850
11000
17,00
-25..+40
160
p. 89 / M3)
Curve
Nominal data
Type
Motor
*3G 630
M3G 150-NA
A
*3G 630
M3G 200-HF
*3G 630
M3G 200-QA
1600
7,2
1800
3
C
4
ηmax.
=
6,4
Curves
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
in H2O
subject to alterations
C
Nominal
voltage range
–
–
–
B
5,6
1200
1000
B
4
4,0
1400
4,8
3
800
3,2
3
A
2
3
2
1,6
400
2,4
4
600
200
0,8
2
pfs
1
0
qV
2000
4000
5000
6000
10000
8000
15000
10000
12000
20000
1
14000
1
25000
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
58
Technical features
and electr. connection
– Material:
n
rpm
Ped
W
I
A
LWA
dB(A)
A
1
1130
2155
3,26
88
A
2
1130
2834
4,30
81
A
3
1130
2900
4,50
78
A
4
1130
2461
3,73
79
B
1
1500
4523
7,00
97
B
2
1500
5763
8,87
92
B
3
1500
6750
10,30
88
B
4
1500
6333
9,69
88
C
1
1850
7459
11,55
101
C
2
1850
10040
15,39
96
C
3
1850
11000
17,00
91
C
4
1850
9894
15,15
92
Mass of centrifugal
module with cube
design
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 89
– EMC: A Interference emission acc. to EN 61000-6-3
A Interference immunity acc. to EN 61000-6-2
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Terminal box design: Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: A UL, CSA, GOST;
B C GOST
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
40,0
64070-2-4013
K3G 630-AP01 -01
77,5
---
---
---
---
---
---
---
K3G 630-AR02 -01
125,0
---
---
---
---
---
K3G 630-AS05 -01
160,0
Centrifugal fan
kg
R3G 630-AP01 -01
Drawings
p. 60 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Centrifugal module
with cube design
Rubber mounting
p. 85
kg
Guard grille
p. 86
Electr. connection
p. 89
59
EC centrifugal fans – RadiPac
backward curved, Ø 630
70
6xØ10.5
R3G 630-AP01-01 (Centrifugal fan)
359 ±2
Depth of screw max. 25 mm
98.5
6xM10
250.5±1
Ø600
Ø634
Ø433
Ø427
Ø716
Ø444 ±3.6
Ø188
0°
6x6
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
6
224
318.3
2
Ø252±0,3
Ø275
Tightening torque 3.5±0.5 Nm
Accessory part: Inlet nozzle 63070-2-4013
not included in the standard scope of delivery (k-value: 438)
Cable gland M20x1,5(3x)
K3G 630-AP01-01 (Centrifugal module with support bracket)
508 ±3
439 ±2.5
o 800
o 652
20
Ø11 (8x)
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
M20x1.5(3x)
o 750±1
Pressure tap (k-value: 438)
60
K3G 630-AR02-01 (Centrifugal module with cube design)
506
652.5
511.5
8xØ11
666
20
4xØ11
*674
4xØ11
*159
660
760
*451
Inlet nozzle with pressure tap (k-value: 438)
Tightening torque
3,5±0.5 Nm
* Screw-on position for rubber mounting
respectively spring elements;
with horizontal shaft position,
only direct installation on the
floor possible and permitted.
M20x1.5 (2x)
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
M25x1.5
Cable diameter
min. 9 mm, max. 16 mm,
tightening torque 6±0.9 Nm
K3G 630-AS05-01 (Centrifugal module with cube design)
506
8xØ11
666
20
711
570
4xØ11
4xØ11
*674
*169
660
760
*500
Inlet nozzle with pressure tap (k-value: 438)
Tightening torque 3,5±0.5 Nm
* Screw-on position for rubber mounting
respectively spring elements;
with horizontal shaft position,
only direct installation on the
floor possible and permitted.
M20x1.5 (2x)
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 6±0.6 Nm
M25x1.5
Cable diameter
min. 16 mm, max. 20.5 mm,
tightening torque 6±0.6 Nm
61
EC centrifugal fans – RadiPac
backward curved, Ø 710
Cube design with inlet nozzle: Sheet steel, galvanised and
plastic-coated in light grey (RAL 7035)
Impeller: Sheet aluminium
Rotor: Coated in black; Electronics enclosure: Die-cast aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54 (acc. to EN 60529)
Insulation class: "F"
Mounting position: Shaft horizontal ( B C for floor installation only) or rotor on bottom;
rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
–
–
–
–
–
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
°C
kg
3~ 380-480
50/60
920
2800
4,30
-25..+40
44
p. 89 / M3)
B
3~ 380-480
50/60
1300
7860
12,00
-25..+40
163
p. 89 / M3)
C
3~ 380-480
50/60
1550
11800
18,00
-25..+40
194
p. 89 / M3)
Curve
Nominal data
Type
Motor
*3G 710
M3G 150-NA
A
*3G 710
M3G 200-LA
*3G 710
M3G 200-QA
Curves
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
in H2O
subject to alterations
C
Nominal
voltage range
–
–
–
B
Technical features
and electr. connection
– Material:
1400
C
1
920
1824
2,72
84
A
2
920
2522
3,77
80
A
3
920
2800
4,30
78
A
4
920
2566
3,82
78
B
1
1300
5116
7,87
96
B
2
1300
6911
10,63
91
B
3
1300
7860
12,00
86
B
4
1300
7367
11,21
87
C
1
1550
7632
11,88
101
C
2
1550
10356
16,00
94
C
3
1550
11800
18,00
88
C
4
1550
11144
17,09
91
A
2,4
2
600
4
2
1,6
3
400
0,8
2
200
pfs
1
0
qV
5000
5000
10000
10000
15000
1
20000
25000
1
cfm
15000
30000
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
62
LWA
dB(A)
4,8
4,0
3,2
3
800
I
A
A
3
4
1000
Ped
W
4
B
1200
n
rpm
ηmax.
=
5,6
1600
6,4
3
Mass of centrifugal
module with cube
design
Mass of
centrifugal fan
Mass of centrifugal
module with support
bracket
– Technical features: See electrical connections p. 89
– EMC: A Interference emission acc. to EN 61000-6-3
A Interference immunity acc. to EN 61000-6-2
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Terminal box design: Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: A UL, CSA, GOST;
B C GOST
Inlet nozzle with one
pressure tap
Centrifugal module
w. support bracket
kg
44,0
64070-2-4013
K3G 710-AP02 -01
92,0
---
---
---
---
---
---
---
K3G 710-AR03 -01
163,0
---
---
---
---
---
K3G 710-AS06 -01
194,0
Centrifugal fan
kg
R3G 710-AP02 -01
Drawings
p. 64 ff.
Inlet nozzle
p. 82 ff.
Spring elements
p. 84
Centrifugal module
with cube design
Rubber mounting
p. 85
kg
Guard grille
p. 86
Electr. connection
p. 89
63
EC centrifugal fans – RadiPac
backward curved, Ø 710
R3G 710-AP02-01 (Centrifugal fan)
70
Depth of screw max. 25 mm
117
6xØ9
394 ±2
6xM10
250.5±1
Ø700
Ø720
Ø488
Ø470.3
Ø806
Ø501+4.6
Ø188
0°
6x6
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
15
250
354
2.5
Ø252±0,3
Ø275
Tightening torque 3.5±0.5 Nm
Accessory part: Inlet nozzle 71075-2-4013
not included in the standard scope of delivery (k-value: 545)
Cable gland M20x1,5(3x)
K3G 710-AP02-01 (Centrifugal module with support bracket)
559 ±3
490 ±2.5
o 960
o 783
25
Ø11 (12x)
Observe the correct
mounting position!
Install the support struts
only as shown in the
view!
M20x1.5(3x)
600 ±1
o 880 ±1
Pressure tap (k-value: 545)
64
K3G 710-AR03-01 (Centrifugal module with cube design)
712.5
579.5
700
20xØ11
864
25
4xØ11
4xØ11
600
750
880
960
*337
*234
*884
Inlet nozzle with pressure tap (k-value: 545)
Tightening torque 3,5±0.5 Nm
* Screw-on position for rubber mounting
respectively spring elements;
with horizontal shaft position,
only direct installation on the
floor possible and permitted.
M20x1.5 (2x)
M25x1.5
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque4±0.6 Nm
Cable diameter
min. 9 mm, max. 16 mm,
tightening torque 6±0.9 Nm
K3G 710-AS06-01 (Centrifugal module with cube design)
700
20xØ11
864
25
759
621
4xØ11
*252.5
*884
*405
4xØ11
600
750
880
960
Inlet nozzle with pressure tap (k-value: 545)
Tightening torque
3,5±0.5 Nm
* Screw-on position for rubber mounting
respectively spring elements;
with horizontal shaft position,
only direct installation on the
floor possible and permitted.
M20x1.5 (2x)
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 6±0.6 Nm
M25x1.5
Cable diameter
min. 16 mm, max. 20.5 mm,
tightening torque 6±0.6 Nm
65
EC centrifugal fans – RadiPac
backward curved, Ø 800
Nominal
voltage range
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
°C
kg
3~ 380-480
50/60
1050
7530
11,60
-25..+40
189
p. 89 / M3)
3~ 380-480
50/60
1370
11600
17,80
-25..+40
196
p. 89 / M3)
Curve
Nominal data
Type
Motor
K3G 800-AR08 -01
M3G 200-QA
A
K3G 800-AS07 -01
M3G 200-QA
B
Curves
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
in H2O
subject to alterations
1200
ηmax.
=
4,0
3,2
4
800
2,4
1,6
200
pfs
400
0,8
3
600
2
2
5000
0
qV
Ped
W
I
A
LWA
dB(A)
A
1
1050
4907
7,58
94
A
2
1050
6555
10,10
88
A
3
1050
7530
11,60
85
A
4
1050
7183
11,02
85
B
1
1370
6755
10,53
106
B
2
1370
9619
14,77
98
B
3
1370
11600
17,80
90
B
4
1370
10690
16,37
93
3
A
1000
n
rpm
4
5,6
1400
B
4,8
1600
6,4
3
5000
10000
15000
1 1
20000
15000
10000
20000
25000
30000
35000
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
66
Technical features
and electr. connection
– Material: Cube design with inlet nozzle: Sheet steel, galvanised and
plastic-coated in light grey (RAL 7035)
Impeller: Sheet aluminium
Rotor: Coated in black; Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "F"
– Mounting position: Shaft horizontal (for floor installation only) or rotor on bottom;
rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
–
–
–
–
–
–
Technical features: See electrical connections p. 89
Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Terminal box design: Electrical connection via terminal strip
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 61800-5-1, CE
Approvals: GOST
Drawings
p. 68 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 89
67
EC centrifugal fans – RadiPac
backward curved, Ø 800
K3G 800-AR08-01 (Centrifugal module with cube design)
783
650
700
20xØ11
864
25
4xØ11
600
750
880
960
4xØ11
*884
Inlet nozzle with pressure tap
(k-value: 695)
* Screw-on position for rubber mounting
respectively spring elements;
with horizontal shaft position,
only direct installation on the
floor possible and permitted.
*251.5
*430
Tightening torque
3,5±0.5 Nm
M20x1.5 (2x)
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
68
M25x1.5
Cable diameter
min. 9 mm, max. 16 mm,
tightening torque 6±0.9 Nm
K3G 800-AS07-01 (Centrifugal module with cube design)
700
20xØ11
864
25
759
621
4xØ11
*884
*252.5
*405
4xØ11
600
750
880
960
Inlet nozzle with pressure tap
(k-value: 695)
* Screw-on position for rubber mounting
respectively spring elements;
with horizontal shaft position,
only direct installation on the
floor possible and permitted.
Tightening torque
3,5±0.5 Nm
M20x1.5 (2x)
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 6±0.6 Nm
M25x1.5
Cable diameter
min. 16 mm, max. 20.5 mm,
tightening torque 6±0.6 Nm
69
EC centrifugal fans – RadiPac
backward curved, Ø 900
Nominal
voltage range
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
°C
kg
3~ 380-480
50/60
860
7520
11,50
-25..+40
222
p. 89 / M3)
3~ 380-480
50/60
1050
8700
13,50
-25..+40
232
p. 89 / M3)
Curve
Nominal data
Type
Motor
K3G 900-AR10 -01
M3G 200-QA
A
K3G 900-AS08 -01
M3G 200-QA
B
Curves
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
1200
4,8 in H2O
subject to alterations
Technical features
and electr. connection
– Material: Cube design with inlet nozzle: Sheet steel, galvanised and
plastic-coated in light grey (RAL 7035)
Impeller: Sheet aluminium
Rotor: Coated in black; Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "F"
– Mounting position: Shaft horizontal (for floor installation only) or rotor on bottom;
rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
3
B
3
3,2
4
2,4
3
600
1,6
2
400
pfs
0,8
2
200
5000
0
qV
5000
10000
15000
1
20000
15000
10000
20000
25000
30000
35000
1
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
70
I
A
LWA
dB(A)
A
1
860
5028
7,72
92
A
2
860
6750
10,33
87
A
3
860
7520
11,50
82
A
4
860
7015
10,72
81
B
1
1050
5036
8,03
99
B
2
1050
7329
11,42
91
B
3
1050
8700
13,50
86
B
4
1050
7744
12,03
87
A
800
Ped
W
4
4,0
1000
n
rpm
ηmax.
=
–
–
–
–
–
–
Technical features: See electrical connections p. 89
Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Terminal box design: Electrical connection via terminal strip
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 61800-5-1, CE
Approvals: GOST
Drawings
p. 72 ff.
Spring elements
p. 84
Rubber mounting
p. 85
Guard grille
p. 86
Electr. connection
p. 89
71
EC centrifugal fans – RadiPac
backward curved, Ø 900
K3G 900-AR10-01 (Centrifugal module with cube design)
930
24xØ11
1084
30
745
612
4xØ11
*1104
Inlet nozzle with pressure tap
(k-value: 900)
* Screw-on position for rubber mounting
respectively spring elements;
with horizontal shaft position,
only direct installation on the
floor possible and permitted.
*203.5
4xØ11
Tightening torque
3,5±0.5 Nm
M20x1.5 (2x)
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
72
400
800
950
1100
1180
*440
M25x1.5
Cable diameter
min. 9 mm, max. 16 mm,
tightening torque 6±0.9 Nm
K3G 900-AS08-01 (Centrifugal module with cube design)
930
24xØ11
1084
30
657
519
4xØ11
*1104
Inlet nozzle with pressure tap
(k-value: 900)
* Screw-on position for rubber mounting
respectively spring elements;
with horizontal shaft position,
only direct installation on the
floor possible and permitted.
*181
*375
4xØ11
400
800
950
1100
1180
Tightening torque
3,5±0.5 Nm
M20x1.5 (2x)
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 6±0.6 Nm
M25x1.5
Cable diameter
min. 16 mm, max. 20.5 mm,
tightening torque 6±0.6 Nm
73
EC centrifugal fans – RadiPac
backward curved, Ø Z50
Hz
rpm
W
A
°C
kg
50/60
380
3560
5,40
-25..+40
350
3~ 380-480
A
p. 89 / M3)
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
Curves
A
250
n
rpm
ηmax.
=
1,2
3
4
1,0
300
200
0,8
150
0,6
3
0,4
50
pfs
100
0,2
2
0
qV
5000
10000
10000
20000
15000
20000
30000
25000
40000
1
30000 cfm
50000
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
74
Technical features
and electr. connection
Mass
VAC
in H2O
subject to alterations
Perm. amb. temp.
M3G 200-QA
Max.
current draw(1)
K3G Z50-AQ11 -01
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
Nominal
voltage range
Curve
– Material: Cube design with inlet nozzle: Sheet steel, galvanised and
plastic-coated in light grey (RAL 7035)
Impeller: Sheet aluminium
Rotor: Coated in black; Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "F"
– Mounting position: Shaft horizontal (for floor installation only) or rotor on bottom;
rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Ped
W
I
A
LWA
dB(A)
A
1
380
2250
3,40
81
A
2
380
3180
4,60
74
A
3
380
3560
5,40
73
A
4
380
3340
4,90
73
–
–
–
–
–
–
Technical features: See electrical connections p. 89
Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Terminal box design: Electrical connection via terminal strip
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 61800-5-1, CE
Approvals: GOST
Drawings
p. 76
Electr. connection
p. 89
75
EC centrifugal fans – RadiPac
backward curved, Ø Z50
K3G Z50-AQ11-01 (Centrifugal module with cube design)
974.3
797.3
30
*1424
*277.3
*566
24xØ11
4xØ11
1500
Tightening torque 3,5±0.5 Nm
Inlet nozzle with pressure tap (k-value: 1730)
* Screw-on position for rubber mounting
respectively spring elements;
with horizontal shaft position,
only direct installation on the
floor possible and permitted.
76
M20x1.5 (2x)
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
M25x1.5
Cable diameter
min. 9 mm, max. 16 mm,
tightening torque 6±0.9 Nm
77
EC centrifugal fans – RadiPac
backward curved, Ø 280 - 450 (compact design)
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
°C
kg
3~ 380-480
50/60
3260
985
1,60
-25..+60
7,1
p. 90 / L6)
B
3~ 380-480
50/60
3170
1650
2,50
-25..+50
12,1
p. 89 / M3)
M3G 112-GA
C
3~ 380-480
50/60
2650
1730
2,60
-25..+60
12,6
p. 89 / M3)
R3G 400-AS23 -01
M3G 150-FF
D
3~ 380-480
50/60
2550
2840
4,20
-25..+60
21,3
p. 89 / M3)
R3G 450-AS24 -01
M3G 150-FF
E
3~ 380-480
50/60
2040
2380
3,60
-25..+60
22,0
p. 89 / M3)
Curve
Nominal
voltage range
Technical features
and electr. connection
– Material: Impeller: Sheet aluminium
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Nominal data
Type
Motor
R3G 280-AJ14 -C1
M3G 084-GF
A
R3G 310-BC38 -01
M3G 112-GA
R3G 355-BD43 -01
Curves
Pa
(1) Nominal data in operating point with maximum load and 400 VAC
1400
5,6 in H2O
subject to alterations
ηmax.
=
3
4,8
4
1000
4,0
4
4
3
3,2
3
3
C
2,4
B
1
3260
703
1,31
89
2
3260
877
1,57
86
A
3
3260
985
1,60
84
A
4
3260
873
1,57
85
B
1
3170
1230
1,83
90
B
2
3170
1523
2,27
88
B
3
3170
1650
2,50
85
B
4
3170
1540
2,30
88
C
1
2650
1248
1,86
90
C
2
2650
1561
2,33
86
C
3
2650
1730
2,60
84
C
4
2650
1629
2,42
86
D
1
2550
2095
3,13
92
D
2
2550
2594
3,84
89
D
3
2550
2840
4,20
86
D
4
2550
2675
3,95
89
E
1
2040
1641
2,48
90
E
2
2040
2156
3,23
85
E
3
2040
2380
3,60
82
E
4
2040
2171
3,24
86
E
D
A
2
2
2
2
0,8
pfs
200
1,6
2
400
0
qV
500
1000
1000
2000
1500
1
2000
3000
1
2500
4000
3000
5000
1
3500
6000
1
4000
7000
4500
8000
5000
1
5500 cfm
9000
m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted!
For detailed information see page 94 ff.
78
LWA
dB(A)
A
3
600
I
A
3
4
800
Ped
W
A
4
1200
n
rpm
– Technical features: See electrical connections p. 89
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: : < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Terminal box design: Electrical connection via terminal strip
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: A VDE, UL, CSA, CCC, GOST are applied for;
B C VDE, GOST;
D E UL, CSA, GOST
Drawings
p. 80 ff.
Inlet nozzle
p. 82 ff.
Guard grille
p. 86
Electr. connection
p. 89 ff.
79
EC centrifugal fans – RadiPac
backward curved, Ø 280 - 450 (compact design)
56.5
4x Ø4.5
R3G 280-AJ14-C1 (Centrifugal fan)
152.4±2
5x
72
53
°
Depth of screw
12-16 mm
Cable gland M16x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 2.5±0.4 Nm
Ø280
Ø325
Ø187.2
Ø197.4 0
Ø284
Ø197
Ø165±0.25
Ø130
+1.8
Ø5.5
Tightening torque
3.5±0.5 Nm
Ø186±0,5
90
126
Accessory part: Inlet nozzle 28075-2-4013
not included in the standard scope of delivery (k-value: 93)
6
60
170.2 ±2
4xØ4.5
R3G 310-BC38-01 (Centrifugal fan)
Accessory part: Inlet nozzle 31575-2-4013
not included in the standard scope of delivery (k-value: 116)
55
Depth of screw
max. 20 mm
6xM10
Ø325
Ø350
Ø 222 +2
Ø 319
Ø211.7
0°
6x6
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø 232
100
147
Tightening torque
3.5±0.5 Nm
Ø 252±0.5
6
60
187.2 ±2
4xØ4.5
R3G 355-BD43-01 (Centrifugal fan)
Accessory part: Inlet nozzle 35675-2-4013
not included in the standard scope of delivery (k-value: 148)
64.4
Depth of screw
max. 20 mm
6xM10
Ø345
Ø370
Ø 250.3 +2.3
Ø 360
Ø239
0°
6x6
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø 232
112
164
80
6
Ø 252±0.5
Tightening torque
3.5±0.5 Nm
R3G 400-AS23-01 (Centrifugal fan)
6xØ9
289.5 ±3
228.5 ±2
70
Accessory part: Inlet nozzle 40075-2-4013
not included in the standard scope of delivery (k-value: 188)
68
Depth of screw
max. 25 mm
14xM10
45
8x
220.5±1
6x60
°
Ø390
Ø413
Ø404
Ø270.9
22.5°
Ø282
°
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
Ø252±0,3
Ø275
9
125
182
Tightening torque
3.5±0.5 Nm
R3G 450-AS24-01 (Centrifugal fan)
320.2 ±3
250.2 ±2
6xØ9
70
Accessory part: Inlet nozzle 45075-2-4013
not included in the standard scope of delivery (k-value: 240)
76
Depth of screw
max. 25 mm
14xM10
6x60
°
Ø430
Ø480
Ø303.4
Ø455
22.5°
Ø317
°
45
8x
220.5±1
Ø232-2
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
tightening torque 4±0.6 Nm
140
204
9
Ø252±0,3
Ø275
Tightening torque
3.5±0.5 Nm
81
Inlet nozzles
Vers. 1
- Material: galvanised sheet steel
Vers. 2
6x6
0°
°
90
4x
Inlet nozzles without measuring device for backward curved centrifugal fans
Part no.
Size
Vers.
For dimensions, see
25070-2-4013
250
1
page 14
28070-2-4013
280
1
page 20
31570-2-4013
310
1
page 26
35670-2-4013
355
1
page 32
40070-2-4013
400
2
page 38
45070-2-4013
450
2
page 44
63072-2-4013
500
2
page 50
63071-2-4013
560
2
page 56
63070-2-4013
630
2
page 60
71070-2-4013
710
2
page 64
subject to alterations
Effects of installation space
Curve:
might be reduced.
1,00
When mounting our product in a rectangular box, air performance
0,99
B
Formula: dh = 2 x B x H / (B + H)
B = Width of box
H = Height of box
D = Outer diameter of the fan
82
0,96
0,95
0,94
0,93
0,92
Correction factor for air flow
dh = Hydraulic diameter
D
D
0,5xD
H
0,97
0,98
D
1,4
1,6
1,8
Hydraulic diameter dh/D
2,0
2,2
2,4
2,6
2,8
Inlet nozzles with measuring device
Vers. 3
(with one pressure
tap)
- Material: galvanised sheet steel
Vers. 4
(with piezometer
ring)
Inlet nozzles with measuring device to determine air flow for backward curved centrifugal fans
Part no.
Part no.
Size
Vers.
For dimensions, see
(4)
250
3/4
page 14
(4)
280
3/4
page 20
31575-2-4013(3) / 31580-2-4013(4)
310
3/4
page 26
35675-2-4013(3) / 35680-2-4013(4)
355
3/4
page 32
(4)
400
3/4
page 38
45075-2-4013(3) / 45080-2-4013(4)
450
3/4
page 44
64025-2-4013(3) / 64002-2-4013(4)
500
3/4
page 50
(4)
560
3/4
page 56
64040-2-4013(3) / 64000-2-4013(4)
630
3/4
page 60
71075-2-4013(3) / 71080-2-4013(4)
710
3/4
page 64
(3)
25075-2-4013
(3)
28075-2-4013
(3)
40075-2-4013
(3)
64030-2-4013
subject to alterations
/ 25080-2-4013
/ 28080-2-4013
/ 40080-2-4013
/ 64001-2-4013
(3)
with one pressure tap
(4)
with piezometer ring (4 pressure taps connected by tubing)
Air flow determination
qV = k . Δp
0,5xD
D
The differential pressure approach compares the static pressure before the
inlet nozzle with the static pressure inside the inlet nozzle. Air flow can be
calculated on the basis of the differential pressure (difference in pressure of
the static pressures) in keeping with the following equation:
qV in [m3/h] und Δp in [Pa]
k takes into account the specific nozzle characteristics.
Differences in static pressure are measured in 1/4 measuring point(s) along
the circumference of the inlet nozzle. Connection on the customer side is
acomplished via a pre-mounted T tube connector. This tube connector is
suited for pneumatic hoses with an internal diameter of 4 mm.
Δp
If constant air flow is to be controlled to, then the nozzle pressure has to be
kept constant:
Δp = qV2 : k2
k-values: (for RadiPac inlet nozzles)
Size
250
280
310
355
400
450
500
k-value
70
93
116
148
188
240
281
Size
560
630
710
800
900
Z50
k-value
348
438
545
695
900
1730
83
Spring elements
- Packaging: part numbers refer to one set
consisting of 4 x spring elements.
Vers. 2
*94
*57
Vers. 1
Delivered in cardboard box.
Ø70
Ø52
M8
M10
* unloaded
Spring elements
Order no. (set)
Type
11001-4-5142
K3G 250-AT39-89
1
360 rpm
14,1 mm
11001-4-5142
K3G 250-AV29-B9
1
340 rpm
16,0 mm
11001-4-5142
K3G 280-AT04-89
1
340 rpm
16,4 mm
11001-4-5142
K3G 280-AU06-B3
1
330 rpm
16,5 mm
11001-4-5142
K3G 280-AU11-C9
1
320 rpm
18,2 mm
11003-4-5142
K3G 310-AX52-96
1
420 rpm
10,3 mm
11003-4-5142
K3G 310-AX54-98
1
390 rpm
12,2 mm
11003-4-5142
K3G 310-BB49-96
1
380 rpm
13,1 mm
11003-4-5142
K3G 310-AZ88-96
1
360 rpm
14,2 mm
11003-4-5142
K3G 355-AX56-96
1
420 rpm
10,5 mm
11003-4-5142
K3G 355-AY43-98
1
370 rpm
13,8 mm
11003-4-5142
K3G 355-AY40-96
1
370 rpm
13,6 mm
11003-4-5142
K3G 400-AY87-96
1
350 rpm
15,2 mm
11005-4-5142
K3G 450-AY86-96
1
470 rpm
8,1 mm
11005-4-5142
K3G 400-AQ23-02
1
430 rpm
10,1 mm
11005-4-5142
K3G 450-AQ24-02
1
390 rpm
12,1 mm
11005-4-5142
K3G 500-AP25-02
1
380 rpm
12,5 mm
11012-4-5142
K3G 630-AR02-01
2
270 rpm
25,7 mm
11013-4-5142
K3G 630-AS05-01
2
330 rpm
17,3 mm
11013-4-5142
K3G 710-AR03-01
2
310 rpm
19,5 mm
11013-4-5142
K3G 710-AS06-01
2
300 rpm
20,3 mm
11013-4-5142
K3G 800-AR08-01
2
280 rpm
23,1 mm
11013-4-5142
K3G 800-AS07-01
2
280 rpm
23,1 mm
11014-4-5142
K3G 900-AR10-01
2
320 rpm
17,8 mm
11014-4-5142
K3G 900-AS08-01
2
320 rpm
17,8 mm
subject to alterations
84
Vers.
Minimum speed
Spring deflection
Rubber mounting
- Packaging: Part numbers refer to one set
consisting of 4 x rubber stops, washers and
nuts.
L
G
T
H
Delivered in plastig bag.
G
D
Rubber mounting
Order no. (set)
Type
Minimum speed
10001-4-5164
K3G 250-AT39-89
1250 rpm
10001-4-5164
K3G 250-AV29-B9
10001-4-5164
K3G 280-AT04-89
10001-4-5164
Spring deflection
D
G
H
L
T
0,9 mm
15
M4
25
10
5
1170 rpm
1,0 mm
15
M4
25
10
5
1160 rpm
1,0 mm
15
M4
25
10
5
K3G 280-AU06-B3
1150 rpm
1,0 mm
15
M4
25
10
5
10001-4-5164
K3G 280-AU11-C9
1100 rpm
1,1 mm
15
M4
25
10
5
10002-4-5164
K3G 310-AX52-96
1390 rpm
0,7 mm
20
M6
25
18
6
10002-4-5164
K3G 310-AX54-98
1270 rpm
0,9 mm
20
M6
25
18
6
10002-4-5164
K3G 310-BB49-96
1230 rpm
0,9 mm
20
M6
25
18
6
10002-4-5164
K3G 310-AZ88-96
1180 rpm
1,0 mm
20
M6
25
18
6
10002-4-5164
K3G 355-AX56-96
1370 rpm
0,7 mm
20
M6
25
18
6
10002-4-5164
K3G 355-AY43-98
1190 rpm
1,0 mm
20
M6
25
18
6
10002-4-5164
K3G 355-AY40-96
1210 rpm
0,9 mm
20
M6
25
18
6
10002-4-5164
K3G 400-AY87-96
1140 rpm
1,1 mm
20
M6
25
18
6
10002-4-5164
K3G 450-AY86-96
980 rpm
1,4 mm
20
M6
25
18
6
10003-4-5164
K3G 400-AQ23-02
950 rpm
1,5 mm
25
M8
25
20
8
10003-4-5164
K3G 450-AQ24-02
870 rpm
1,8 mm
25
M8
25
20
8
10003-4-5164
K3G 500-AP25-02
860 rpm
1,8 mm
25
M8
25
20
8
10005-4-5164
K3G 630-AR02-01
680 rpm
2,9 mm
40
M10
40
28
10
10006-4-5164
K3G 630-AS05-01
740 rpm
2,4 mm
50
M10
50
28
10
10005-4-5164
K3G 710-AR03-01
620 rpm
3,5 mm
40
M10
40
28
10
10006-4-5164
K3G 710-AS06-01
680 rpm
2,9 mm
50
M10
50
28
10
10005-4-5164
K3G 800-AR08-01
570 rpm
4,1 mm
40
M10
40
28
10
10006-4-5164
K3G 800-AS07-01
640 rpm
3,3 mm
50
M10
50
28
10
10005-4-5164
K3G 900-AR10-01
520 rpm
5,0 mm
40
M10
40
28
10
10006-4-5164
K3G 900-AS08-01
580 rpm
3,9 mm
50
M10
50
28
10
subject to alterations
85
Air intake guard grilles
Vers. 1
Vers. 2
b
a
a
Ød
Ød
Ød
a
e
- Material: steel wire, plastic coated
Vers. 3
e
b
e
b
Air intake guard grilles for backward curved centrifugal fans (according to EN ISO 13857)
Part no.
Size
Vers.
a
b
d
e
Strut pitch
78129-2-4039
250
1
260
4,5
210
2,8
4 x 90°
78130-2-4039
280
1
280
4,5
230
2,8
4 x 90°
78131-2-4039
310
1
325
4,5
250
2,8
4 x 90°
78132-2-4039
355
1
345
4,5
310
2,8
4 x 90°
78133-2-4039
400
2
390
8,5
350
3,8
3 x 120°
78134-2-4039
450
2
430
8,5
410
3,8
3 x 120°
78139-2-4039
500
2
445
8,5
410
3,8
3 x 120°
78137-2-4039
560
3
490
8,5
430
3,8
6 x 60°
78138-2-4039
630
2
600
8,5
490
3,8
3 x 120°
78141-2-4039
710
3
700
8,5
598
4,8
6 x 60°
78141-2-4039
800
3
700
8,5
598
4,8
6 x 60°
78142-2-4039
900
3
850
8,5
680
4,8
6 x 60°
subject to alterations
86
87
Electrical connections EC
K1)
Technical features:
• PFC (passive)
• Control input 0-10 VDC / PWM
• Output 10 VDC max. 1,1 mA
• Alarm relay
• Over-temperature protected electronics / motor
Notes on various control possibilities and their applications
Umin = 15 V
Imax =
10 mA
Mains
50/60 Hz
L
black
N
blue
PE
green/yellow
+
-
NC
white1
+
white2
Voltage output
red
+10 V
max. 1.1 mA
U
PWM
-
10 K
12 V
Alarm relay:
Break for failure
(2 A, 250 VAC, AC1)
Lin/PWM control input
yellow
0-10 VDC /
PWM
1 μF
GND
blue
Speed setting
PWM 1 - 10 kHz
Speed setting
with variable
resistance
Speed setting
Full speed
1 V - 10 V
10 V -> n=max
approx. 1 V -> n=min
< 1 V -> n=0
100% PWM -> n=max
approx. 10% PWM -> n=min
< 10% PWM -> n=0
start up at > 1.4 V
start up at > 14 %
Customer circuit
Connection
+10 V
0-10 V
PWM
GND
green/yellow white1
COM
blue
Line 2
NC
N
black
PE
L
Line 1
Fan
white2
red
yellow
blue
Line
Connection Colour Assignment / function
Line
Connection Colour Assignment / function
1
L
black
Mains 50/60 Hz, phase
2
+10 V
N
blue
Mains 50/60 Hz, neutral
0-10 V / PWM yellow
Control input (Impedance 100 kΩ)
PE
NC
green/yel
white1
Protective earth
GND
GND
COM
white2
88
Status relay, floating status contact,
break with error
Status relay, floating status contact,
changeover contact, common connection
(2 A, 250 V, min. 10 mA, AC1)
red
blue
Voltage output +10 V max. 1.1 mA
Electrical connections EC
M3)
Motor current limitation, Alarm relay
Line undervoltage / phase failure detection
Over-temperature protected electronics / motor
Reverse polarity and locked-rotor protection, Soft start
External 24 V input (programming)
External release input
Operation and alarm display
Control interface with SELV potential safely disconnected from the mains
KL3
KL2
KL1
Ain2 I
Aout
Ain1 I
Din1
NO
COM
NC
2
3
4
5
6
7
1
2
3
L3
+20 V
+10 V
1
L2
Ain2 U
Ain1 U
14
GND
13
GND
12
Din3
11
RS B
10
Din2
9
RS A
8
L1
•
•
•
•
•
•
•
•
PE
Technical features:
• PFC (passive)
• integrated PID controller
• Control input 0-10 VDC / PWM
• Input for sensor 0-10 V or 4-20 mA
• Slave output 0-10 V max. 5 mA
• Output 20 VDC (±20 %) max. 50 mA
• Output 10 VDC (+10 %) max. 10 mA
• RS485 MODBUS-RTU
1
2
3
Connector Pin
Connection Assignment / function
KL1
1
L1
Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz
2
L2
Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz
3
L3
Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz
PE
Earth connection, PE connection
1
NO
Status relay, floating status contact, close with error
2
COM
Status relay, floating status contact, changeover contact, common connection (2 A, 250 V, min. 10 mA, AC1)
3
NC
Status relay, floating status contact, break with error
1
RSA
Bus connection RS485; RSA; MODBUS RTU
2
RSB
Bus connection RS485; RSB; MODBUS RTU
3/10
GND
Signal ground for control interface
4
Ain1 U
Analogue input 1 (set value); 0-10 V; Ri= 100 kΩ; parametrisable curves; only usable as alternative to input Ain1 I
5
+10 V
Fixed voltage output 10 VDC; +10 V ±3 %; max. 10 mA; short circuit proof; power supply for ext. devices (e.g. potentiometer)
6
7
Ain1 I
Din1
Analogue input 1 (set value); 4-20 mA; Ri= 100 Ω; parametrisable curve; only usable as alternative to input Ain1 U
PE
KL2
KL3
Digital input 1: enabling of electronics; enabling: open pin or applied voltage 5 to 50 VDC; disabling: bridge to GND or
applied voltage < 1 VDC; reset function: triggers software reset after a level change to < 1V
8
Din2
Digital input 2: parameter set switch 1/2; according to EEPROM setting, thr valid/used parameter set is selectable per BUS or per
digital input Din2. Parameter set 1: open oin or applied voltage 5 to 50 VDC; parameter set 2: bridge to GND or applied voltage < 1 VDC
9
Din3
Digital input 3: Control characteristic of the integrated controller; according to EEPROM setting, the control characteristic of the integrated
controller is normally/inversely selectable per BUS or per digital input; normal: open pin or applied voltage 5 to 50 VDC (control deviation =
actual sensor value - set value); inverse: bridge to GND or applied voltage < 1 VDC control deviation = set value - actual sensor value)
11
Ain2 U
Analogue input 2; actual sensor value 0-10 V; Ri= 100 kΩ; parametrisable curve; only usable as alternative to input Ain2 I
12
+20 V
Fixed voltage output 20 VDC; +20 V +25/-10 %; max. 50 mA; short circuit proof; power supply for ext. devices (e.g. sensors)
13
14
Ain2 I
Aout
Analogue input 2; actual sensor value 4-20 mA; Ri= 100 Ω; parametrisable curve; only usable as alternative to input Ain2 U
Analogue output 0-10 V; max. 5 mA; output of the actual motor control factor (output voltage of electronics)/of the actual motor speed;
function selectable per BUS; parametrisable curve
89
Electrical connections EC
L6)
Alarm relay
Line undervoltage / phase failure detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
L1
PE
KL1
NC
COM
NO
OUT
GND
+10 V
0-10 V
PWM
+20 V
KL2
4-20 mA
GND
0-10 V
PWM
RS B
RS A
RS B
RS A
KL3
L3
•
•
•
•
•
•
L2
Technical features:
• PFC (passive)
• Integrated PID controller
• Control input 0-10 VDC / PWM
• Input for sensor 0-10 V or 4-20 mA
• Slave output 0-10 V max. 3 mA
• Output 20 VDC (±20 %) max. 50 mA
• Output 10 VDC (+10 %) max. 10 mA
• RS485 MODBUS
Connector Connection Assignment / function
Connector Connection Assignment / function
PE
KL1
KL3
KL2
PE
Protective earth
OUT
Master output 0-10 V max. 5 mA
L3
Mains; L3
GND
GND
L2
Mains; L2
L1
NC
Mains; L1
Status relay, floating status contact, break with error
0-10 V / PWM Control / Actual value input (Impedance 100 kΩ)
+10 V
Supply for external potentiometer,
COM
Status relay, floating status contact, changeover contact, common connection (2 A, 250 V, min. 10 mA, AC1)
+20 V
NO
Status relay, floating status contact, close with error
4-20 mA
10 VDC (±3 %), max. 10 mA
Supply for external sensor,
20 VDC (+25 % / -10 %), max. 50 mA
Control / Actual value input
0-10 V / PWM Control / Actual value input (Impedance 100 kΩ)
90
GND
GND
RSB
RS485 interface for MODBUS RTU; RSB
RSA
RS485 interface for MODBUS RTU; RSA
RSB
RS485 interface for MODBUS RTU; RSB
RSA
RS485 interface for MODBUS RTU; RSA
Electrical connections EC
L7)
Alarm relay
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
KL1
L
NC
COM
NO
OUT
GND
+10 V
0-10 V
PWM
+20 V
KL2
4-20 mA
GND
0-10 V
PWM
RS B
RS A
RS B
RS A
KL3
PE
•
•
•
•
•
•
N
Technical features:
• PFC (active)
• Integrated PID controller
• Control input 0-10 VDC / PWM
• Input for sensor 0-10 V or 4-20 mA
• Slave output 0-10 V max. 3 mA
• Output 20 VDC (±20 %) max. 50 mA
• Output 10 VDC (+10 %) max. 10 mA
• RS485 MODBUS
Connector Connection Assignment / function
Connector Connection Assignment / function
PE
KL1
KL3
KL2
PE
Protective earth
OUT
Master output 0-10 V max. 3 mA
N
Mains 50/60 Hz. neutral
GND
GND
L
NC
Mains 50/60 Hz, phase
Status relay, floating status contact, break with error
0-10 V / PWM Control / Actual value input (Impedance 100 kΩ)
COM
Status relay, floating status contact, changeover contact, common connection (2 A, 250 V, min. 10 mA, AC1)
NO
+10 V
Supply for external potentiometer,
10 VDC (+10 %) max. 10 mA
+20 V
Status relay, floating status contact, close with error
Supply for external sensor,
20 VDC (±20 %) max. 50 mA
4-20 mA
Control / Actual value input
0-10 V / PWM Control / Actual value input (Impedance 100 kΩ)
GND
GND
RSB
RS485 interface for MODBUS RTU; RSB
RSA
RS485 interface for MODBUS RTU; RSA
RSB
RS485 interface for MODBUS RTU; RSB
RSA
RS485 interface for MODBUS RTU; RSA
91
Electrical connections EC
L9)
Alarm relay
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
+20 V
Ain2 I
Aout
+10 V
Ain1 I
Din1
N
Ain2 U
Ain1 U
L1
GND
GND
KL1
PE
Din3
RS B
NO
Din2
KL2
RS A
KL3
NC
•
•
•
•
•
•
COM
Technical features:
• PFC (active)
• Integrated PID controller
• Control input 0-10 VDC / PWM
• Input for sensor 0-10 V or 4-20 mA
• Slave output 0-10 V max. 3 mA
• Output 20 VDC (±20 %) max. 50 mA
• Output 10 VDC (+10 %) max. 10 mA
• RS485 MODBUS
Connector Connection Assignment / function
Connector Connection Assignment / function
KL1
KL3
PE
KL2
Din1
N
Mains; neutral
L1
Mains; L1
PE
NC
Protective earth
Status relay, floating status contact, break with error
Ain1 I
Analogue set value input, 4-20 mA (impedance 100 Ω),
COM
Status relay, floating status contact, changeover contact, common connection (2 A, 250 V, min. 10 mA, AC1)
+10 V
Supply for external potentiometer,
NO
Digital input 1 (enabling / disabling of electronics),
Enabling: Pin open or applied voltage 5 to 50 VDC
Disabling: Bridge to GND or applied voltage < 1 VDC
only to be used as alternative to terminal Ain1 U
Status relay, floating status contact, close with error
10 VDC (±3 %) max. 10 mA
Ain1U
Analogue set value input, 0-10 V (impedance 100 kΩ),
GND
GND
RSB
RS485 interface for MODBUS RTU; RSB
RSA
Aout
RS485 interface for MODBUS RTU; RSA
only to be used as alternative to terminal Ain1 I
Analogue output 0-10 V max. 5 mA, reading of current
motor speed / current motor control factor
Ain2 I
Analog. actual value input, 4-20mA (impedance 100Ω),
+20 V
Supply for external sensor,
only to be used as alternative to terminal Ain2 U
20 VDC (+25 % / -10%) max. 40 mA
Ain2 U
Analog. actual value input, 0-10 V (impedance 100 kΩ),
GND
Din3
GND
only to be used as alternative to terminal Ain2 I
Digital input 3 (switch Normal / Inverse),
The preset effective direction of the integrated
controller can be selected via BUS or via digital input
Normal/Inverse.
Normal: Pin open or applied voltage 5 to 50 VDC
Inverse: Bridge to GND or applied voltage < 1 VDC
Din2
Digital input 2 (switch Day / Night),
The preset set of parameters can be selected via BUS
or via digital input Day/Night.
Day: Pin open or applied voltage 5 to 50 VDC
Night: Bridge to GND or applied voltage < 1 VDC
92
Electrical connections EC
P2)
Motor current limitation, Alarm relay
Line undervoltage / phase failure detection
Over-temperature protected electronics / motor
Locked-rotor protection, Soft start
Control interface with SELV potential safely disconnected from the mains
11
10
1-10V
2
3
10V -> n = max
1V -> n = min
<1V -> n = 0
9
8
7
6
5
4
3
2
Speed setting
with potentiometer
Set value
e.g. for pressure
5
10K
4-20mA
1
4
3
3/7
2
2
6
1
3
2
1
RSB
RSA
RSA
RSB
RSB
GND
0-10V/PWM
IN
47K
I
4-20mA
1
O
+20V/50mA
20V
+10V/10mA
10V
33
0-10V/PWM
100
GND
47K
2.2μF
OUT
KL2
NO
OUT
GND
A2
12
3/7
4
KL3
RSA
COM
NC
A1
Speed
setting
14
12
Full
Speed
•
•
•
•
•
11
Technical features:
• PFC (passive)
• integrated PID controller
• Control input 0-10 VDC / PWM
• Input for sensor 0-10 V or 4-20 mA
• Slave output 0-10 V max. 5 mA
• Output 20 VDC (±25 % / -10 %) max. 50 mA
• Output 10 VDC (+3 %) max. 10 mA
• External 24 V input (programming)
• RS485 MODBUS RTU
KL1
L1
P
L2
N
L3
PE
PE
Customer circuit
PE
Connection
Fan
Connector Pin
Connection
Assignment / function
PE
PE
Earth connection, PE connection
1/2/3
L1, L2, L3
Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz
1
NC
Status relay, floating status contact; option 1: break with error; option 2: break with error for run monitor error message
2
COM
Status relay, floating status contact; changeover contact; common connection (2 A, 250 V, min. 10 mA, AC1)
3
1
NO
OUT
Status relay, floating status contact; option 1: close with error; option 2: close with run monitor error message
2/8
GND
Signal ground for control interface KL3; SELV
3/7
0-10 V
Control input 0-10 VDC, impedance 100 kΩ; only usable as alternative to 4-20 mA input, SELV
4
+10 V
Fixed voltage output 10 VDC (±3 %), max. 10 mA; power supply for ext. devices (e.g. potentiometer), SELV
5
+20 V
Fixed voltage output 20 VDC (+25 % / -10 %), max. 50 mA; power supply for ext. devices (e.g. sensors), SELV
6
4-20 mA
Control input 4-20 mA, impedance 100 Ω; only usable as alternative to 0-10 V input, SELV
9/11
RSB
RS485 interface for MODBUS RTU; RSB
10/12
RSA
RS485 interface for MODBUS RTU; RSA
KL1
KL2
KL3
Analogue output 0-10 V; max. 5 mA, SELV, output of the actual motor duty cycle (PWM): 1 V corresponds to 10 % PWM,
10 V corresponds to 100 % PWM
93
Technical parameters & scope
High standards for all ebm-papst products
Here at ebm-papst, we constantly strive to further improve our products in order to be able to offer you the best possible product for your application.
Careful monitoring of the market ensures that technical innovations are reflected in the improvements of our products. Based on the technical parameters listed below and the ambience you want our product to operate in, we here at ebm-papst can always work out the best solution for your specific
application..
General performance parameters
The majority of our products use maintenance-free ball bearings for
Any deviations from the technical data and parameters described here
any mounting position possible. As an option, sleeve bearings can be
are listed on the product-specific data sheet.
used, which is indicated on the product-specific data sheet wherever
Type of protection
The type of protection is specified in the product-specific data sheets.
applicable.
The service life L10 of the ball bearings can be taken as approx. 40,000
operating hours at an ambient temperature of 40 °C, yet this estimate
Insulation class
can vary according to the actual ambient conditions.
The insulation class is specified in the product-specific data sheets.
We will gladly provide you with a lifetime calculation taking into account
your specific operating conditions.
Mounting position
The mounting position is specified in the product-specific data sheets.
Motor protection / thermal protection
Information on motor protection and thermal protection is provided in the
Condensate discharge holes
product-specific data sheets.
Information on the condensate discharge holes is provided in the
Depending on motor type and field of application, the following protective
product-specific data sheets.
features are realised:
Mode of operation
– Thermal overload protection (TOP), either in-circuit or external
The mode of operation is specified in the product-specific data sheets.
– PTC with electronic diagnostics
– Impedance protection
Protection class
– Thermal overload protection (TOP) with electronic diagnostics
The protection class is specified in the product-specific data sheets.
– Current limitation via electronics
Service life
The service life of ebm-papst products depends on two major factors:
– The service life of the insulation system
– The service life of the bearing system
If an external TOP is connected, the customer has to make sure to
connect a conventional trigger device for switching it off.
Products without fitted TOP and without protection against improper use,
a motor protection complying with the valid standards has to be installed.
The service life of the insulation system mainly depends on voltage level,
Mechanical strain / performance parameters
temperature and ambient conditions, such as humidity and condensation.
All ebm-papst products are subjected to comprehensive tests complying
The service life of the bearing system depends mainly on the thermal load
with the normative specifications. In addition to this, the tests also reflect
on the bearing.
the vast experience and expertise of ebm-papst.
94
Vibration test
Standards
Vibration tests are carried out in compliance with
Information on standards is provided in the product-specific data sheets.
– Vibration test in operation according to DIN IEC 68, parts 2-6
– Vibration test at standstill according to DIN IEC 68, parts 2-6
EMC
Information on EMC standards is provided in the product-specific data
Shock load
sheets.
Shock load tests are carried out in compliance with
Complying with the EMC standards has to be established on the final
– Shock load according to DIN IEC 68, parts 2-27
appliance, as different mounting situations can result in changed EMC
Balancing quality
properties.
Testing the balancing quality is carried out in compliance with
Leakage current
– Residual imbalance according to DIN ISO 1940
Information on the leakage current is provided in the product-specific
– Standard balancing quality level G 6.3
data sheets.
Should you require a higher balancing quality level for your specific
Measuring is according to IEC 60990.
application, please let us know and specify this when ordering your
product.
Approvals
In case you require a specific approval for your ebm-papst product
Chemo-physical strain / performance parameters
(VDE, UL, GOST, CCC, CSA, etc.) please let us know.
Should you have questions about chemo-physical strain, please direct
Most of our products can be supplied with the relevant approval.
them to your ebm-papst contact.
Information on existing approvals is provided in the product-specific
Fields of application, industries and applications
data sheets.
Our products are used in various industries and applications:
Air performance measurements
Ventilation, air-conditioning and refrigeration technology, clean room
All air performance measurements are carried out on suction side and on
technology, automotive and rail technology, medical and laboratory tech-
chamber test beds conforming to the specifications as per ISO 5801 and
nology, electronics, computer and office technology, telecommunications,
DIN 24163. The fans under test are installed in the measuring chamber at
household appliances, heating, machines and plants, drive engineering.
free air intake and exhaust (installation category A) and are operated at
Our products are not designed for use in the aviation and aerospace
nominal voltage, with AC also at nominal frequency, and without any
industry!
additional components such as guard grilles.
Legal and normative directives
The products described in this catalogue are designed, developed and
As required by the standard, the air performance curves correspond to
an air density of 1.2 kg/m3.
produced in keeping with the standards in place for the relevant product
and, if known, the conditions governing the relevant fields of application.
95
Technical parameters & scope
Measurement conditions for air and noise measurement
Sound pressure level and sound level
ebm-papst products are measured under the following conditions:
All acoustic values are established according to ISO 13347, DIN 45635
– Axial and diagonal fans in direction of rotation “V” in full nozzle and
and ISO 3744/3745 to accuracy class 2 and given in A-rated form.
without guard grille
When the sound pressure level (Lp) is measured, the microphone is on
– Backward curved centrifugal fans, free-running and with inlet nozzle
the intake side of the fan being tested, usually at a distance of 1 m on
– Forward curved single and dual inlet centrifugal fans with housing
the fan axis.
Noise measurements
All noise measurements are carried out in low-reflective test rooms with
reverberant floor. Thus the ebm-papst acoustic test chambers meet the
requirements of precision class 1 according to DIN EN ISO 3745. For noise
measurement, the fans being tested are placed in a reverberant wall and
operated at nominal voltage (for AC, also at nominal frequency) without
additional attachments such as the guard grille.
To measure the sound power level (Lw), 10 microphones are distributed
over an enveloping surface on the intake side of the fan being tested
(see graphic). The sound power level measured can be roughly calculated
from the sound pressure level by adding 7 dB.
Measuring configuration as per ISO 13347-3 respectively DIN 45635-38:
10 measuring points
d≥D
h = 1,5d ... 4,5d
D
1,5d
Measurement area S = 6d2 + 7d (h + 1,5d)
h
3d
2d
96
9 dB. Thus the overall sound level of the installation can be expected to be 84 dB(A).
15
10
9
Example: 8 A3G800 axial fans are on a condenser. According to the data sheet, the sound pressure level of a fan is approximately 75 dB(A). The level increase measured from the diagram is
5
the noise values specified in the data sheet. This is shown in the diagram opposite.
0
The noise characteristics of multiple identical fans can be determined in advance based on
[dB]
[dB(A)]
Adding 2 noise sources with the same level results in a level increase of approx. 3 dB.
Increase in sound pressure / sound power level
Combined level of multiple same-level sound sources
1
2
3
4
5
6 7 8 9 10
15
20 25
point and an axial fan A3G710 with 71 dB(A) in a ventilation unit. The level difference is 4 dB.
The level increase can now be read in the diagram as approx. 1.5 dB. This means that the
overall sound level of the unit can be expected to be 76.5 dB(A).
3
2
1,5
Example: There is an axial fan A3G800 with a sound pressure level of 75 dB(A) at the operating
1
levels given in the data sheet. This is shown in the diagram opposite.
0
The acoustic performance of two different fans can be predetermined based on the sound
Increase in sound pressure / sound power level
Combined level of two different-level sound sources
[dB]
[dB(A)]
Number of sources of sound with identical level
0
4
8
12
16
20
Sound power level is independent of distance to the sound source. In contrast to this, sound
-10
pressure level decreases the further away the noise source is. The adjacent diagram shows the
0
[dB]
[dB(A)]
Distance laws
24
[dB]
[dB(A)]
Difference in level with two sources of sound
decrease in level under far sound field conditions. Far sound field conditions apply whenever the
ably smaller. The following example only applies to far sound field conditions and can vary
strongly depending on the installation effects:
With an axial fan A3G300, a sound pressure level of 65 dB(A) was measured at a distance of
1 m. According to the adjacent diagram, at a distance of 20 m we would get a reduction by
-20
-26
-30
In the near field of the fan, other correlations apply and the decrease in levels can be consider-
-40
this complex topic. Per doubling of distance, the level in the far sound field decreases by 6 dB.
Decrease in sound pressure level
distance between microphone and fan is big when compared to fan diameter and wavelength to
be considered. For more information on far sound field, please consult the relevant literature on
1
Distance
2
5
10
20
50
100
[m]
26 dB, i.e. a sound pressure level of 39 dB(A).
97
ebm-papst in Germany
ebm-papst Mulfingen GmbH & Co. KG
Bachmühle 2
74673 Mulfingen
GERMANY
Phone +49 7938 81-0
Fax +49 7938 81-110
[email protected]
98
ebm-papst St. Georgen GmbH & Co. KG
Hermann-Papst-Straße 1
78112 St. Georgen
GERMANY
Phone +49 7724 81-0
Fax +49 7724 81-1309
[email protected]
Berlin
Dipl.-Ing. (TH) Jens Duchow
Händelstraße 7
16341 Panketal
GERMANY
Phone +49 30 944149-62
Fax +49 30 944149-63
[email protected]
Heilbronn / Heidelberg
Dipl.-Ing. Mark Gartner
Gehrweg 12
74199 Unterheinriet
GERMANY
Phone +49 7130 404569-1
Fax +49 7130 404569-2
[email protected]
Bielefeld
Dipl.-Ing. (FH) Wolf-Jürgen Weber
Niehausweg 13
33739 Bielefeld
GERMANY
Phone +49 5206 91732-31
Fax +49 5206 91732-35
[email protected]
Kassel
Dipl.-Ing. (FH) Ralph Brück
Hoherainstraße 3 b
35075 Gladenbach
GERMANY
Phone +49 6462 4071-10
Fax +49 6462 4071-11
[email protected]
Dortmund
Dipl.-Ing. (FH) Hans-Joachim Pundt
Auf den Steinern 3
59519 Möhnesee-Völlinghausen
GERMANY
Phone +49 2925 800-407
Fax +49 2925 800-408
[email protected]
Koblenz
Winfried Schaefer
Hinter der Kirch 10
56767 Uersfeld
GERMANY
Phone +49 2657 16-96
Fax +49 2657 16-76
[email protected]
Frankfurt
Dipl.-Ing. Christian Kleffmann
Dr.-Hermann-Krause-Straße 23
63452 Hanau
GERMANY
Phone +49 6181 1898-12
Fax +49 6181 1898-13
[email protected]
Munich
Dipl.-Wirt.-Ing. (FH) Jens Peter
Landsbergerstraße 14
86932 Pürgen
GERMANY
Phone +49 8196 99877-54
Fax +49 8196 99877-55
[email protected]
Halle
Dipl.-Ing. (TU) Michael Hanning
Lercheneck 4
06198 Salzatal / OT Lieskau
GERMANY
Phone +49 345 55124-56
Fax +49 345 55124-57
[email protected]
Nuremberg
Dipl.-Wirt.-Ing. (FH) Axel Resch
Dr.-August-Koch-Str. 1
91639 Wolframs-Eschenbach
GERMANY
Phone +49 9875 9783-170
Fax +49 9875 9783-171
[email protected]
Hamburg
Ingenieurbüro Breuell GmbH
Ing. Dirk Kahl
Elektroingenieur
Grützmühlenweg 48
22339 Hamburg
GERMANY
Phone +49 40 538092-19
Fax +49 40 538092-84
[email protected]
Offenburg
Dipl.-Ing. (FH) Ralf Braun
Hubeneck 21
77704 Oberkirch
GERMANY
Phone +49 7802 9822-52
Fax +49 7802 9822-53
[email protected]
fan agent
Stuttgart
Dipl.-Ing. (FH) Rudi Weinmann
Hindenburgstraße 100/1
73207 Plochingen
GERMANY
Phone +49 7153 9289-80
Fax +49 7153 9289-81
[email protected]
compact fan agent
motor specialist
ebm-papst Landshut GmbH
Hofmark-Aich-Straße 25
84030 Landshut
GERMANY
Phone +49 871 707-0
Fax +49 871 707-465
[email protected]
Ulm
M.Sc. Reinhard Sommerreißer
Am Germanenring 13
86674 Baar / Schwaben
GERMANY
Phone +49 8276 5899-775
Fax +49 8276 5899-776
[email protected]
Distributoren
Frankfurt
R.E.D. Handelsgesellschaft mbH
Gutenbergstraße 3
63110 Rodgau - Jügesheim
GERMANY
Phone +49 6106 841-0
Fax +49 6106 841-111
[email protected]
www.red-elektromechanik.de
Hamburg
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
22339 Hamburg
GERMANY
Phone +49 40 538092-20
Fax +49 40 538092-84
[email protected]
Munich
A. Schweiger GmbH
Ohmstraße 1
82054 Sauerlach
GERMANY
Phone +49 8104 897-0
Fax +49 8104 897-90
[email protected]
www.schweiger-gmbh.com
(1 to 5 pieces)
North
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
22339 Hamburg
GERMANY
Phone +49 40 538092-20
Fax +49 40 538092-84
[email protected]
South
HDS Ventilatoren Vertriebs GmbH
Glaswiesenstraße 1
74677 Dörzbach
GERMANY
Phone +49 7937 80355-20
Fax +49 7937 80355-25
[email protected]
www.hds-gmbh.net
motor agent
ebm-papst in Europe
Europe
Austria
ebm-papst Motoren & Ventilatoren GmbH
Straubingstraße 17
4030 Linz
AUSTRIA
Phone +43 732 321150-0
Fax +43 732 321150-20
[email protected]
www.ebmpapst.at
Belarus
ebm-papst Bel AgmbH
Lipkovskaya Gasse 34
Office No.6, Room 106,107
223010 Minsk
BELARUS
Phone +375 17 3851556
Fax +375 17 3851556
[email protected]
www.ebmpapst.by
Belgium
ebm-papst Benelux B.V.
Sales office Belgium-Luxemburg
Romeinsestraat 6/0101
Research Park Haasrode
3001 Heverlee-Leuven
BELGIUM
Phone +32 16 396-200
Fax +32 16 396-220
[email protected]
www.ebmpapst.be
Bulgaria
ebm-papst Romania S.R.L.
Str. Tarnavei No. 20
500327 Brasov
ROMANIA
Phone +40 268 331859
Fax +40 268 312805
[email protected]
Croatia
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Czech Republic / Slovakia
ebm-papst CZ s.r.o.
Kaštanová 34a
620 00 Brno
CZECH REPUBLIC
Phone +420 544 502-411
Fax +420 547 232-622
[email protected]
www.ebmpapst.cz
Denmark
ebm-papst Denmark ApS
Vallensbækvej 21
2605 Brøndby
DENMARK
Phone +45 43 631111
Fax +45 43 630505
[email protected]
www.ebmpapst.dk
Estonia
ebm-papst Oy, Eesti Filiaal
Kesk tee 13
Aaviku küla, Jüri Tehnopark
75301 Rae Vald, Harjumaa
ESTONIA
Phone +372 65569-78
Fax +372 65569-79
www.ebmpapst.ee
Finland
ebm-papst Oy
Puistotie 1
02760 Espoo
FINLAND
Phone +358 9 887022-0
Fax +358 9 887022-13
[email protected]
www.ebmpapst.fi
France
ebm-papst sarl
ZI Nord - rue A. Mohler
BP 62
67212 Obernai Cedex
FRANCE
Phone +33 820 326266
Fax +33 3 88673883
[email protected]
www.ebmpapst.fr
Greece
Helcoma
Th. Rotas & Co OE
Davaki 65
17672 Kallithea-Attiki
GREECE
Phone +30 210 9513-705
Fax +30 210 9513-490
[email protected]
www.helcoma.gr
Hungary
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Iceland
RJ Engineers
Stangarhyl 1a
110 Reykjavik
ICELAND
Phone +354 567 8030
Fax +354 567 8015
[email protected]
www.rj.is
Ireland
ebm-papst UK Ltd.
Chelmsford Business Park
Chelmsford Essex CM2 5EZ
UNITED KINGDOM
Phone +44 1245 468555
Fax +44 1245 466336
[email protected]
www.ebmpapst.co.uk
AuBren Limited
Portlaoise Business & Technology Park
Mountrath Road
Portlaoise, Co. Laois
IRELAND
Phone +353 57 8664343
Fax +353 57 8664346
[email protected]
www.aubren.com
Italy
ebm-papst Srl
Via Cornaggia 108
22076 Mozzate (Co)
ITALY
Phone +39 0331 836201
Fax +39 0331 821510
[email protected]
www.ebmpapst.it
Macedonia
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
99
ebm-papst in Europe
Netherlands
ebm-papst Benelux B.V.
Engelseweg 127
5705 AC Helmond
NETHERLANDS
Phone +31 492 502-900
Fax +31 492 502-950
[email protected]
www.ebmpapst.nl
Russia
ebm-papst Ural GmbH
Posadskaja-Strasse, 23(E), 3
620102 Ekaterinburg
RUSSIA
Phone +7 343 2338000
Fax +7 343 2337788
[email protected]
www.ebmpapst.ur.ru
Switzerland
ebm-papst AG
Rütisbergstrasse 1
8156 Oberhasli
SWITZERLAND
Phone +41 44 73220-70
Fax +41 44 73220-77
[email protected]
www.ebmpapst.ch
Norway
ebm-papst AS
P.B. 173 Holmlia
1203 Oslo
NORWAY
Phone +47 22 763340
Fax +47 22 619173
[email protected]
www.ebmpapst.no
ebm-papst Rus GmbH
proezd 4529, vladenie 5, stroenie 1
141000 Mytistschi, Oblast Moskau
RUSSIA
Phone +7 495 9807524
Fax +7 495 5140924
[email protected]
www.ebmpapst.ru
Turkey
Akantel Elektronik San. Tic. LTD. Sti.
Atatürk Organize Sanayi
Bölgesi 10007 SK. No.:6
35620 Cigli-Izmir
TURKEY
Phone +90 232 3282090
Fax +90 232 3280270
[email protected]
www.ebmpapst.com.tr
Poland
ebm-papst Polska Sp. z o.o.
ul. Annopol 4A
03236 Warszawa
POLAND
Phone +48 22 6757819
Fax +48 22 6769587
[email protected]
www.ebmpapst.pl
Portugal
ebm-papst (Portugal), Lda.
Centro Empresarial de Alverca
Rua de Adarse, Vale D’Ervas
Corpo D / Fracção 3
2615-178 Alverca do Ribatejo
PORTUGAL
Phone +351 218 394 880
Fax +351 218 394 759
[email protected]
www.ebmpapst.pt
Romania
ebm-papst Romania S.R.L.
Str. Tarnavei Nr. 20
500327 Brasov
ROMANIA
Phone +40 268 331859
Fax +40 268 312805
[email protected]
100
fan agent
Serbia & Montenegro
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Spain
ebm-papst Ibérica S.L.
Avda. del Sistema Solar, 29
28830 San Fernando de Henares (Madrid)
SPAIN
Phone +34 91 6780894
Fax +34 91 6781530
[email protected]
www.ebmpapst.es
Sweden
ebm-papst AB
Äggelundavägen 2
17562 Järfälla
SWEDEN
Phone +46 10 4544400
Fax +46 8 362306
[email protected]
www.ebmpapst.se
compact fan agent
Ukraine
ebm-papst Ukraine LLC
Lepse Boulevard, 4, Building 21
03067 Kiev
UKRAINE
Phone +38 044 2063091
Fax +38 044 2063091
[email protected]
www.ebmpapst.ua
United Kingdom
ebm-papst UK Ltd.
Chelmsford Business Park
Chelmsford Essex CM2 5EZ
UNITED KINGDOM
Phone +44 1245 468555
Fax +44 1245 466336
[email protected]
www.ebmpapst.co.uk
ebm-papst Automotive & Drives (UK) Ltd.
The Smithy
Fidlers Lane
East Ilsley, Berkshire RG20 7LG
UNITED KINGDOM
Phone +44 1635 2811-11
Fax +44 1635 2811-61
A&[email protected]
www.ebmpapst-ad.com
motor specialist
motor agent
ebm-papst in America and Africa
America
Argentina
ebm-papst de Argentina S.A.
Hernandarias 148 Lomas del Mirador
Pcia. de Buenos Aires (1752)
ARGENTINA
Phone +54 11 46576135
Fax +54 11 46572092
[email protected]
www.ebmpapst.com.ar
Brasil
ebm-papst Motores Ventiladores Ltda.
Av. José Giorgi, 301 Galpões B6+B7
Condominio Logical Center
06707-100 Cotia - São Paulo
BRAZIL
Phone +55 11 4613-8700
Fax +55 11 4777-1456
[email protected]
www.ebmpapst.com.br
USA
ebm-papst Inc.
P.O. Box 4009
100 Hyde Road
Farmington, CT 06034
UNITED STATES
Phone +1 860 674-1515
Fax +1 860 674-8536
[email protected]
www.ebmpapst.us
ebm-papst Automotive & Drives, Inc.
3200 Greenfield, Suite 255
Dearborn, MI 48120
UNITED STATES
Phone +1 313 406-8080
Fax +1 313 406-8081
[email protected]
www.ebmpapst-automotive.us
Africa
South Africa
ebm-papst South Africa (Pty) Ltd.
P.O. Box 3124
1119 Yacht Avenue
2040 Honeydew
SOUTH AFRICA
Phone +27 11 794-3434
Fax +27 11 794-5020
[email protected]
www.ebmpapst.co.za
Canada
ebm-papst Canada Inc.
1800 Ironstone Manor, Unit 2
Pickering, Ontario, L1W3J9
CANADA
Phone +1 905 420-3533
Fax +1 905 420-3772
[email protected]
www.ebmpapst.ca
Mexico
ebm Industrial S. de R.L. de C.V.
Paseo de Tamarindos 400-A-5to Piso
Col. Bosques de las Lomas
Mexico 05120, D.F.
MEXICO
Phone +52 55 3300-5144
Fax +52 55 3300-5243
[email protected]
www.ebmpapst.com.mx
101
ebm-papst in Asia and Australia
Asia
China
ebm-papst Ventilator (Shanghai) Co., Ltd.
No. 418, Huajing Road
WaiGaoQiao Free Trade Zone
No. 2001, Yang Gao (N) Road
200131 Shanghai
P.R. of CHINA
Phone +86 21 5046-0183
Fax +86 21 5046-1119
[email protected]
www.ebmpapst.com.cn
Hong Kong
ebm-papst Hong Kong Ltd.
Room 17E, MG Tower
133 Hoi Bun Road, Kwun Tong
Hong Kong
P.R. of CHINA
Phone +852 2145-8678
Fax +852 2145-7678
[email protected]
India
ebm-papst India Pvt. Ltd.
26/3, G.N.T. Road, Erukkencherry
Chennai-600118
INDIA
Phone +91 44 25372556
Fax +91 44 25371149
[email protected]
www.ebmpapst.in
Indonesia
ebm-papst Indonesia
Representative Office
German Centre, 4th Floor, Suite 4470
Jl. Kapt. Subijono Dj. Bumi Serpong Damai
15321 Tangerang
INDONESIA
Phone +62 21 5376250
Fax +62 21 5388305
[email protected]
Israel
Polak Bros. Import Agencies Ltd.
9 Hamefalsim Street
Kiryat Arie, Petach-Tikva 49514
ISRAEL
Phone +972 3 9100300
Fax +972 3 5796679
[email protected]
www.polak.co.il
102
fan agent
Japan
ebm-papst Japan K.K.
Attend on Tower 13F
Shinyokohama 2-8-12, Kohoku-ku
222-0033 Yokohama-City, Kanagawa
JAPAN
Phone +81 45 47057-51
Fax +81 45 47057-52
[email protected]
www.ebmpapst.jp
Thailand
ebm-papst Thailand Co., Ltd.
99/9 Moo 2, Central Chaengwattana Tower
14th Floor, Room 1402
Chaengwattana Road Bangtarad, Pakkret
11120 Nonthaburi
THAILAND
Phone +66 2 8353785-7
Fax +66 2 8353788
[email protected]
Korea
ebm-papst Korea Co. Ltd.
6F, Trutec Bldg.
12, WorldCupbuk-ro 56-gil
Mapo-Gu
Seoul 121-835
KOREA
Phone +82 2 366213-24
Fax +82 2 366213-26
[email protected]
www.ebmpapst.co.kr
United Arab Emirates
ebm-papst Middle East FZE
PO Box 17755
Jebel Ali Free Zone / FZS1 / AP05
Dubai
UNITED ARAB EMIRATES
Phone +971 4 88608-26
Fax +971 4 88608-27
[email protected]
www.ebmpapst.ae
Malaysia
ebm-papst Malaysia
Representative Office
Unit 12-2, Jalan USJ Sentral 3
Persiaran Subang, Selangor Darul Ehsan
47600 Subang Jaya
MALAYSIA
Phone +60 3 8024-1680
Fax +60 3 8024-8718
[email protected]
Singapore
ebm-papst SEA Pte. Ltd.
No. 23 Ubi Road 4
#06-00 Olympia Industrial Building
Singapore 408620
SINGAPORE
Phone +65 65513789
Fax +65 68428439
[email protected]
Taiwan
ETECO Engineering & Trading Corp.
10F-I, No. 92, Teh-Wei Str.
Tsow-Inn District, Kaohsiung
TAIWAN
Phone +886 7 557-4268
Fax +886 7 557-2788
[email protected]
www.ebmpapst.com.tw
compact fan agent
motor specialist
Vietnam
ebm-papst Vietnam
Representative Office
Room #102, 25 Nguyen Van Thu Street
District 1
Ho Chi Minh City
VIETNAM
Phone +84 8 39104099
Fax +84 8 39103970
[email protected]
Australia
Australia
ebm-papst A&NZ Pty Ltd.
10 Oxford Road
Laverton North, Victoria, 3026
AUSTRALIA
Phone +61 3 9360-6400
Fax +61 3 9360-6464
[email protected]
www.ebmpapst.com.au
New Zealand
ebm-papst A&NZ Pty Ltd.
61 Hugo Johnston Drive, Unit H
Penrose 1061, Auckland
NEW ZEALAND
PO Box 112278,
Penrose 1642, Auckland
Phone +64 9 525-0245
Fax +64 9 525-0246
[email protected]
www.ebmpapst.com.au
motor agent
103
www.ebmpapst.com
37797-7-8811
37903-7-8811
· 2014-06
· 2013-11
· KH-3’
Printed in Germany
ebm-papst
Mulfingen GmbH & Co. KG
Bachmühle 2
74673 Mulfingen
Germany
Phone +49 7938 81-0
Fax +49 7938 81-110
[email protected]