80V, 1A NPN Small Signal Transistor

2N3019, 2N3019S, 2N3700
Low Power Transistors
NPN Silicon
Features
• MIL−PRF−19500/391 Qualified
• Available as JAN, JANTX, and JANTXV
http://onsemi.com
COLLECTOR
3
MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
Characteristic
Symbol
Value
Unit
Collector −Emitter Voltage
VCEO
80
Vdc
Collector −Base Voltage
VCBO
140
Vdc
Emitter −Base Voltage
VEBO
7.0
Vdc
Collector Current − Continuous
IC
1.0
Adc
Total Device Dissipation @ TA = 25°C
2N3019, 2N3019S
2N3700
PT
Total Device Dissipation @ TC = 25°C
2N3019, 2N3019S
2N3700
PT
Operating and Storage Junction
Temperature Range
TJ, Tstg
Symbol
Thermal Resistance, Junction to Ambient
2N3019, 2N3019S
2N3700
RqJA
Thermal Resistance, Junction to Case
2N3019, 2N3019S
2N3700
RqJC
1
EMITTER
mW
800
500
W
5.0
1.0
−65 to
+200
°C
Max
Unit
THERMAL CHARACTERISTICS
Characteristic
2
BASE
TO−5
CASE 205AA
STYLE 1
2N3019
TO−39
CASE 205AB
STYLE 1
2N3019S
TO−18
CASE 206AA
STYLE 1
2N3700
°C/W
195
325
°C/W
30
150
ORDERING INFORMATION
Device
Package
Shipping
TO−5
Bulk
TO−39
Bulk
TO−18
Bulk
JAN2N3019
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
JANTX2N3019
JANTXV2N3019
JAN2N3019S
JANTX2N3019S
JANTXV2N3019S
JAN2N3700
JANTX2N3700
JANTXV2N3700
© Semiconductor Components Industries, LLC, 2012
August, 2012 − Rev. 2
1
Publication Order Number:
2N3019/D
2N3019, 2N3019S, 2N3700
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Symbol
Characteristic
Min
Max
Unit
80
−
−
−
10
10
nAdc
mAdc
−
10
nAdc
−
10
mAdc
50
90
100
50
15
300
−
300
300
−
−
−
0.2
0.5
−
1.1
5.0
20
80
400
−
12
−
60
−
4.0
−
400
−
30
OFF CHARACTERISTICS
V(BR)CEO
Collector −Emitter Breakdown Voltage
(IC = 30 mAdc)
Emitter−Base Cutoff Current
(VEB = 5.0 Vdc)
(VEB = 7.0 Vdc)
IEBO
Collector−Emitter Cutoff Current
(VCE = 90 Vdc)
ICEO
Collector−Base Cutoff Current
(VCB = 140 Vdc)
ICBO
Vdc
ON CHARACTERISTICS (Note 1)
DC Current Gain
(IC = 0.1 mAdc, VCE = 10 Vdc)
(IC = 10 mAdc, VCE = 10 Vdc)
(IC = 150 mAdc, VCE = 10 Vdc)
(IC = 500 mAdc, VCE = 10 Vdc)
(IC = 1.0 Adc, VCE = 10 Vdc)
hFE
Collector −Emitter Saturation Voltage
(IC = 150 mAdc, IB = 15 mAdc)
(IC = 500 mAdc, IB = 50 mAdc)
VCE(sat)
Base −Emitter Saturation Voltage
(IC = 150 mAdc, IB = 15 mAdc)
VBE(sat)
−
Vdc
Vdc
SMALL−SIGNAL CHARACTERISTICS
Magnitude of Small−Signal Current Gain
(IC = 50 mAdc, VCE = 10 Vdc, f = 20 MHz)
|hfe|
Small−Signal Current Gain
(IC = 1.0 mAdc, VCE = 5 Vdc, f = 1 kHz)
hfe
Output Capacitance
(VCB = 10 Vdc, IE = 0, 100 kHz ≤ f ≤ 1.0 MHz)
Cobo
Input Capacitance
(VEB = 0.5 Vdc, IC = 0, 100 kHz ≤ f ≤ 1.0 MHz)
Cibo
Noise Figure
(VCE = 10 Vdc, IC = 100 mAdc, Rg = 1 kW, PBW = 200 Hz)
NF
Collector−Base Time Constant
(VCB = 10 Vdc, IC = 10 mAdc, f = 79.8 MHz)
r’b,CC
−
−
pF
pF
dB
ps
SWITCHING CHARACTERISTICS
Pulse Response
(Reference Figure in MIL−PRF−19500/391)
ton + toff
1. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%.
http://onsemi.com
2
ns
2N3019, 2N3019S, 2N3700
PACKAGE DIMENSIONS
TO−5 3−Lead
CASE 205AA
ISSUE B
B
U
P
C
L
R
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSION J MEASURED FROM DIAMETER A TO EDGE.
4. LEAD TRUE POSITION TO BE DETERMINED AT THE GUAGE
PLANE DEFINED BY DIMENSION R.
5. DIMENSION F APPLIES BETWEEN DIMENSION P AND L.
6. DIMENSION D APPLIES BETWEEN DIMENSION L AND K.
7. BODY CONTOUR OPTIONAL WITHIN ZONE DEFINED BY DIMEN­
SIONS A, B, AND T.
8. DIMENSION B SHALL NOT VARY MORE THAN 0.010 IN ZONE P.
A
B
DETAIL X
F
U
A
SEATING
PLANE
K
NOTE 5
E
T
NOTE 7
D NOTES 4 & 6
0.007 (0.18MM) A B S C
3X
DETAIL X
M
N
H
2
1
3
J
M
LEAD IDENTIFICATION
DETAIL
C
DIM
A
B
C
D
E
F
H
J
K
L
M
N
P
R
T
U
MILLIMETERS
MIN
MAX
8.89
9.40
8.00
8.51
6.10
6.60
0.41
0.53
0.23
3.18
0.41
0.48
0.71
0.86
0.73
1.02
38.10
44.45
6.35
--45_BSC
5.08 BSC
--1.27
1.37 BSC
--0.76
2.54
---
INCHES
MIN
MAX
0.350
0.370
0.315
0.335
0.240
0.260
0.016
0.021
0.009
0.125
0.016
0.019
0.028
0.034
0.029
0.040
1.500
1.750
0.250
--45 _BSC
0.200 BSC
--0.050
0.054 BSC
--0.030
0.100
---
STYLE 1:
PIN 1. EMITTER
2. BASE
3. COLLECTOR
TO−39 3−Lead
CASE 205AB
ISSUE A
B
A
B
DETAIL X
U
P
C
L
R
F
U
A
SEATING
PLANE
K
NOTE 5
E
T
NOTE 7
D NOTES 4 & 6
0.007 (0.18MM) A B S C
3X
DETAIL X
M
N
H
2
1
3
J
M
C
LEAD IDENTIFICATION
DETAIL
http://onsemi.com
3
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSION J MEASURED FROM DIAMETER A TO EDGE.
4. LEAD TRUE POSITION TO BE DETERMINED AT THE GUAGE
PLANE DEFINED BY DIMENSION R.
5. DIMENSION F APPLIES BETWEEN DIMENSION P AND L.
6. DIMENSION D APPLIES BETWEEN DIMENSION L AND K.
7. BODY CONTOUR OPTIONAL WITHIN ZONE DEFINED BY DIMEN­
SIONS A, B, AND T.
8. DIMENSION B SHALL NOT VARY MORE THAN 0.010 IN ZONE P.
DIM
A
B
C
D
E
F
H
J
K
L
M
N
P
R
T
U
MILLIMETERS
MIN
MAX
8.89
9.40
8.00
8.51
6.10
6.60
0.41
0.48
0.23
3.18
0.41
0.48
0.71
0.86
0.73
1.02
12.70
14.73
6.35
--45_BSC
5.08 BSC
--1.27
1.37 BSC
--0.76
2.54
---
STYLE 1:
PIN 1. EMITTER
2. BASE
3. COLLECTOR
INCHES
MIN
MAX
0.350
0.370
0.315
0.335
0.240
0.260
0.016
0.019
0.009
0.125
0.016
0.019
0.028
0.034
0.029
0.040
0.500
0.580
0.250
--45 _BSC
0.200 BSC
--0.050
0.054 BSC
--0.030
0.100
---
2N3019, 2N3019S, 2N3700
PACKAGE DIMENSIONS
TO−18 3−Lead
CASE 206AA
ISSUE A
B
A
B
DETAIL X
U
P
C
L
R
F
U
A
SEATING
PLANE
K
NOTE 5
E
T
NOTE 7
D NOTES 4 & 6
0.007 (0.18MM) A B S C
3X
DETAIL X
M
N
H
2
1
3
J
M
C
LEAD IDENTIFICATION
DETAIL
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSION J MEASURED FROM DIAMETER A TO EDGE.
4. LEAD TRUE POSITION TO BE DETERMINED AT THE GUAGE
PLANE DEFINED BY DIMENSION R.
5. DIMENSION F APPLIES BETWEEN DIMENSION P AND L.
6. DIMENSION D APPLIES BETWEEN DIMENSION L AND K.
7. BODY CONTOUR OPTIONAL WITHIN ZONE DEFINED BY DIMEN­
SIONS A, B, AND T.
DIM
A
B
C
D
E
F
H
J
K
L
M
N
P
R
T
U
MILLIMETERS
MIN
MAX
5.31
5.84
4.52
4.95
4.32
5.33
0.41
0.53
--0.76
0.41
0.48
0.91
1.17
0.71
1.22
12.70
19.05
6.35
--45_BSC
2.54 BSC
--1.27
1.37 BSC
--0.76
2.54
---
INCHES
MIN
MAX
0.209
0.230
0.178
0.195
0.170
0.210
0.016
0.021
--0.030
0.016
0.019
0.036
0.046
0.028
0.048
0.500
0.750
0.250
--45 _BSC
0.100 BSC
--0.050
0.054 BSC
--0.030
0.100
---
STYLE 1:
PIN 1. EMITTER
2. BASE
3. COLLECTOR
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
4
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
2N3019/D