ISL43140, ISL43141, ISL43142 ® Data Sheet November 2002 Low-Voltage, Single and Dual Supply, High Performance, Quad SPST, Analog Switches Features The Intersil ISL43140–ISL43142 devices are CMOS, precision, quad analog switches designed to operate from a single +2V to +12V supply or from a ±2V to ±6V supply. Targeted applications include battery powered equipment that benefit from the devices’ low power consumption (1µW), low leakage currents (1nA max), and fast switching speeds (tON = 30ns, tOFF = 18ns). A 12Ω maximum RON flatness ensures signal fidelity, while channel-to-channel mismatch is guaranteed to be less than 2.5Ω. The 3mm x 3mm Quad NoLead Flatpack (QFN) package alleviates board space limitations, making this newest line of low-voltage switches an ideal solution. • Four Separately Controlled SPST Switches The ISL43140/ISL43141/ISL43142 are quad single-pole/ single-throw (SPST) devices. The ISL43140 has four normally closed (NC) switches; the ISL43141 has four normally open (NO) switches; the ISL43142 has two NO and two NC switches and can be used as a dual SPDT, or a dual 2:1 multiplexer. Table 1 summarizes the performance of this family. TABLE 1. FEATURES AT A GLANCE ISL43140 ISL43141 ISL43142 Number of Switches 4 4 4 Configuration All NC All NO 2 NC / 2 NO 10.8V RON 50Ω 50Ω 50Ω 10.8V tON / tOFF 30ns / 18ns 30ns / 18ns 30ns / 18ns ±4.5V RON 50Ω 50Ω 50Ω ±4.5V tON / tOFF 40ns / 15ns 40ns / 15ns 40ns / 15ns 4.5V RON 110Ω 110Ω 110Ω 4.5V tON / tOFF 50ns / 20ns 50ns / 20ns 50ns / 20ns 2.7V RON 200Ω 200Ω 200Ω 2.7V tON / tOFF 120ns / 25ns 120ns / 25ns 120ns / 25ns Packages 16 Ld SOIC (N), 16 Ld 3x3 QFN, 16 Ld TSSOP FN6032 • Fully Specified at ±5V, 12V, 5V, and 3V Supplies for 10% Tolerances • Pin Compatible with DG411/DG412/DG413 • ON Resistance (RON) . . . . . . . . . . . . . . . . . . . . . . . . 50Ω • RON Matching Between Channels. . . . . . . . . . . . . . . . . . . 2Ω • Low Charge Injection . . . . . . . . . . . . . . . . . . . . . . 5pC (Max) • Low Power Consumption (PD) . . . . . . . . . . . . . . . . . . . .<1µW • Low Leakage Current (Max at 85oC) . . . . . . . . . . . . . 5nA • Fast Switching Action - tON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30ns - tOFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18ns • Guaranteed Break-Before-Make (ISL43142 only) • Minimum 2000V ESD Protection per Method 3015.7 • TTL, CMOS Compatible Applications • Battery Powered, Handheld, and Portable Equipment - Cellular/Mobile Phones - Pagers - Laptops, Notebooks, Palmtops • Communications Systems - Military Radios - RF “Tee” Switches • Test Equipment - Ultrasound - Electrocardiograph • Heads-Up Displays • Audio and Video Switching • General Purpose Circuits - +3V/+5V DACs and ADCs - Digital Filters - Operational Amplifier Gain Switching Networks - High Frequency Analog Switching - High Speed Multiplexing Related Literature • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved ISL43140, ISL43141, ISL43142 (Note 1) IN1 IN2 COM2 15 COM2 16 15 14 13 13 V+ V- 4 GND 5 12 N.C. NC4 6 11 NC3 10 COM3 COM4 7 NC1 1 12 NC2 V- 2 11 V+ GND 3 10 N.C. NC4 4 9 9 IN3 IN4 8 NC3 COM2 ISL43141 (QFN) TOP VIEW 16 IN2 15 COM2 16 15 14 13 14 NO2 NO1 3 8 IN2 COM1 2 7 IN1 IN1 1 6 COM1 ISL43141 (SOIC, TSSOP) TOP VIEW 5 COM3 14 NC2 NC1 3 IN3 COM1 2 16 IN2 IN4 IN1 1 ISL43140 (QFN) TOP VIEW COM1 ISL43140 (SOIC, TSSOP) TOP VIEW COM4 NO1 1 12 NO2 V- 2 11 V+ GND 3 10 N.C. NO4 4 9 13 V+ 12 N.C. NO4 6 11 NO3 10 COM3 COM4 7 9 IN3 5 COM4 IN4 8 IN2 COM2 ISL43142 (QFN) TOP VIEW 16 IN2 15 COM2 16 15 14 13 14 NC2 NO1 3 8 IN1 IN1 1 COM1 2 7 COM1 ISL43142 (SOIC, TSSOP) TOP VIEW 6 NO3 COM3 GND 5 IN3 V- 4 IN4 Pinouts NO1 1 12 NC2 V- 2 11 V+ 13 V+ V- 4 GND 3 10 N.C. 10 COM3 NO4 4 9 COM4 7 9 IN3 IN4 8 NOTE: 1. Switches Shown for Logic “0” Input. 2 5 6 7 8 COM3 11 NC3 IN3 NO4 6 IN4 12 N.C. COM4 GND 5 NC3 ISL43140, ISL43141, ISL43142 Truth Table ISL43140 LOGIC ISL43141 ISL43142 SW 1, 2, 3, 4 SW 1, 2, 3, 4 SW 1, 4 SW 2, 3 0 ON OFF OFF ON 1 OFF ON ON OFF NOTE: Logic “0” ≤ 0.8V. Logic “1” ≥ 2.4V. Pin Descriptions PIN FUNCTION V+ Positive Power Supply Input V- Negative Power Supply Input. Connect to GND for Single Supply Configurations. GND Ground Connection IN Digital Control Input COM Analog Switch Common Pin NO Analog Switch Normally Open Pin NC Analog Switch Normally Closed Pin N.C. No Internal Connection Ordering Information PART NO. (BRAND) (NOTE 2) TEMP. RANGE (oC) PACKAGE PKG. NO. ISL43140IB -40 to 85 16 Ld SOIC (N) M16.15 ISL43140IR* (140I) -40 to 85 16 Ld QFN L16.3x3 ISL43140IV -40 to 85 16 Ld TSSOP M16.173 ISL43141IB -40 to 85 16 Ld SOIC (N) M16.15 ISL43141IR* (141I) -40 to 85 16 Ld QFN L16.3x3 ISL43141IV -40 to 85 16 Ld TSSOP M16.173 ISL43142IB -40 to 85 16 Ld SOIC (N) M16.15 ISL43142IR* (142I) -40 to 85 16 Ld QFN L16.3x3 ISL43142IV -40 to 85 16 Ld TSSOP M16.173 NOTES: 2. Most surface mount devices are available on tape and reel; add “-T” to suffix. * In Development. 3 ISL43140, ISL43141, ISL43142 Absolute Maximum Ratings Thermal Information V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V V- to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -15 to 0.3V All Other Pins (Note 3) . . . . . . . . . . . . . ((V-) - 0.3V) to ((V+) + 0.3V) Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 10mA Peak Current, IN, NO, NC, or COM (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . 20mA ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . .>2kV Thermal Resistance (Typical, Note 4) Operating Conditions Temperature Range ISL4314XIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC θJA (oC/W) 16 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . 115 16 Ld QFN Package. . . . . . . . . . . . . . . . . . . . . . . . . 75 16 Ld TSSOP Package . . . . . . . . . . . . . . . . . . . . . . 150 Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC Moisture Sensitivity (See Technical Brief TB363) All Other Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1 QFN Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 2 Maximum Storage Temperature Range. . . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC and TSSOP - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 3. Signals on NC, NO , COM, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to maximum current ratings. 4. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications: ±5V Supply PARAMETER Test Conditions VSUPPLY = ±4.5V to ±5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 5), Unless Otherwise Specified TEST CONDITIONS TEMP (oC) (NOTE 6) MIN Full V- - V+ V 25 - 50 65 Ω TYP (NOTE 6) MAX UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON Resistance, RON VS = ±4.5V, ICOM = 1.0mA, VNO or VNC = ±3V, See Figure 5 Full - - 75 Ω RON Matching Between Channels, ∆RON VS = ±4.5V, ICOM = 1.0mA, VNO or VNC = ±3V 25 - 2 2.5 Ω Full - - 5 Ω RON Flatness, RFLAT(ON) VS = ±4.5V, ICOM = 1.0mA, VNO or VNC = ±3V, Note 8 25 - 10 12 Ω Full - - 13 Ω NO or NC OFF Leakage Current, INO(OFF) or INC(OFF) VS = ±5.5V, VCOM = ±4.5V, VNO or VNC = +4.5V, Note 7 COM OFF Leakage Current, ICOM(OFF) VS = ±5.5V, VCOM = ±4.5V, VNO or VNC = +4.5V, Note 7 COM ON Leakage Current, ICOM(ON) VS = ±5.5V, VCOM = VNO or VNC = ±4.5V, Note 7 25 -1 0.01 1 nA Full -5 - 5 nA 25 -1 0.01 1 nA Full -5 - 5 nA 25 -2 0.01 2 nA Full -10 - 10 nA Full 2.4 1.6 - V DIGITAL INPUT CHARACTERISTICS Input Voltage High, VINH Full - 1.6 0.8 V VS = ±5.5V, VIN = 0V or V+ Full -0.5 0.03 0.5 µA VS = ±4.5V, VNO or VNC = ±3V, RL = 300Ω, CL = 35pF, VIN = 0 to 3V, See Figure 1 25 - 40 80 ns Full - - 100 ns VS = ±4.5V, VNO or VNC = ±3V, RL = 300Ω, CL = 35pF, VIN = 0 to 3V, See Figure 1 25 - 15 30 ns Full - - 40 ns Input Voltage Low, VINL Input Current, IINH, IINL DYNAMIC CHARACTERISTICS Turn-ON Time, tON Turn-OFF Time, tOFF Break-Before-Make Time Delay (ISL43142), tD VS = ±5.5V, VNO or VNC = ±3V, RL = 300Ω, CL = 35pF, VIN = 0 to 3V, See Figure 3 Full 5 20 - ns Charge Injection, Q CL = 1.0nF, VG = 0V, RG = 0Ω, See Figure 2 25 - 1 5 pC NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 7 - pF COM OFF Capacitance, CCOM(OFF) f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 7 - pF COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 14 - pF 4 ISL43140, ISL43141, ISL43142 Electrical Specifications: ±5V Supply Test Conditions VSUPPLY = ±4.5V to ±5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 5), Unless Otherwise Specified (Continued) TEMP (oC) (NOTE 6) MIN TYP RL = 50Ω, CL = 15pF, f = 100kHz, VNO or VNC = 1VRMS, See Figures 4, 6, and 19 25 - >90 25 - <-90 - dB All Hostile Crosstalk RL = 50Ω, CL = 15pF, f = 10MHz, VNO or VNC = 1VRMS, See Figure 19 25 - -60 - dB Power Supply Rejection Ratio RL = 50Ω, CL = 15pF, f = 1MHz, See Figure 20 25 - 60 - dB Full ±2 - ±6 V 25 -1 0.05 1 µA µA PARAMETER TEST CONDITIONS OFF Isolation Crosstalk, Note 9 (NOTE 6) MAX UNITS - dB POWER SUPPLY CHARACTERISTICS Power Supply Range VS = ±5.5V, VIN = 0V or V+, Switch On or Off Positive Supply Current, I+ Negative Supply Current, I- Full -1 - 1 25 -1 0.05 1 µA Full -1 - 1 µA NOTES: 5. VIN = Input voltage to perform proper function. 6. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 7. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25oC. 8. Flatness is defined as the delta between the maximum and minimum RON values over the specified voltage range. 9. Between any two switches. Electrical Specifications: 12V Supply PARAMETER Test Conditions: V+ = +10.8V to +13.2V, V- = GND = 0V, VINH = 5V, VINL = 0.8V (Note 5), Unless Otherwise Specified TEST CONDITIONS TEMP (oC) (NOTE 6) MIN Full 0 - V+ V 25 - 50 65 Ω Full - 60 75 Ω TYP (NOTE 6) MAX UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG V+ = 10.8V, ICOM = 1.0mA, VNO or VNC = 9V, See Figure 5 ON Resistance, RON 25 - 2 2.5 Ω Full - - 5 Ω 25 - 8 12 Ω Full - 9 13 Ω 25 -1 - 1 nA Full -5 - 5 nA 25 -1 - 1 nA Full -5 - 5 nA RON Matching Between Channels, ∆RON V+ = 10.8V, ICOM = 1.0mA, VNO or VNC = 9V RON Flatness, RFLAT(ON) V+ = 10.8V, ICOM = 1.0mA, VNO or VNC = 3V, 6V, 9V, Note 8 NO or NC OFF Leakage Current, INO(OFF) or INC(OFF) V+ = 13.2V, VCOM = 1V, 10V, VNO or VNC = 10V, 1V, Note 7 COM OFF Leakage Current, ICOM(OFF) V+ = 13.2V, VCOM = 10V, 1V, VNO or VNC = 1V, 10V, Note 7 COM ON Leakage Current, ICOM(ON) V+ = 13.2V, VCOM = 1V, 10V, or VNO or VNC = 1V, 10V, Note 7 25 -2 - 2 nA Full -10 - 10 nA Input Voltage High, VINH Full 3.5 3.1 - V Input Voltage Low, VINL Full - - 0.8 V V+ = 13.2V, VIN = 0V or V+ Full -1 - 1 µA Turn-ON Time, tON V+ = 10.8V, VNO or VNC = 10V, RL = 300Ω, CL = 35pF, VIN = 0 to 3.3V, See Figure 1 25 - 30 70 ns Full - 34 100 ns Turn-OFF Time, tOFF V+ = 10.8V, VNO or VNC = 10V, RL = 300Ω, CL = 35pF, VIN = 0 to 3.3V, See Figure 1 25 - 18 50 ns Full - 20 75 ns Full 0 8 - ns DIGITAL INPUT CHARACTERISTICS Input Current, IINH, IINL DYNAMIC CHARACTERISTICS Break-Before-Make Time Delay (ISL43142), tD V+ = 13.2V, VNO or VNC = 10V, RL = 300Ω, CL = 35pF, VIN = 0 to 3.3V, See Figure 3 5 ISL43140, ISL43141, ISL43142 Electrical Specifications: 12V Supply PARAMETER Test Conditions: V+ = +10.8V to +13.2V, V- = GND = 0V, VINH = 5V, VINL = 0.8V (Note 5), Unless Otherwise Specified (Continued) TEST CONDITIONS TEMP (oC) (NOTE 6) MIN TYP - 5 15 pC (NOTE 6) MAX UNITS Charge Injection, Q CL = 1.0nF, VG = 0V, RG = 0Ω, See Figure 2 25 OFF Isolation RL = 50Ω, CL = 15pF, f = 100kHz, VNO or VNC = 1VRMS, See Figures 4, 6, and 19 25 - >90 - dB 25 - <-90 - dB All Hostile Crosstalk RL = 50Ω, CL = 15pF, f = 10MHz, VNO or VNC = 1VRMS, See Figure 19 25 - -60 - dB Power Supply Rejection Ratio RL = 50Ω, CL = 15pF, f = 1MHz, See Figure 20 25 - 60 - dB Crosstalk, Note 9 NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 7 - pF COM OFF Capacitance, CCOM(OFF) f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 7 - pF COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 14 - pF POWER SUPPLY CHARACTERISTICS V+ = 13.2V, VIN = 0V or V+, Switch On or Off Positive Supply Current, I+ Negative Supply Current, I- Electrical Specifications: 5V Supply PARAMETER 25 -1 0.05 1 µA Full -1 - 1 µA 25 -1 0.05 1 µA Full -1 - 1 µA Test Conditions: V+ = +4.5V to +5.5V, V- = GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 5), Unless Otherwise Specified TEST CONDITIONS TEMP (oC) MIN (NOTE 6) Full 0 - V+ V 25 - 110 120 Ω Full - - 150 Ω TYP MAX (NOTE 6) UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON Resistance, RON V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3.5V, See Figure 5 RON Matching Between Channels, ∆RON V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3.5V RON Flatness, RFLAT(ON) V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 1.5V to 4.5V, Note 8 NO or NC OFF Leakage Current, INO(OFF) or INC(OFF) V+ = 5.5V, VCOM = 1V, 4.5V, VNO or VNC = 4.5V, 1V, Note 7 COM OFF Leakage Current, ICOM(OFF) V+ = 5.5V, VCOM = 1V, 4.5V, VNO or VNC = 4.5V, 1V, Note 7 COM ON Leakage Current, ICOM(ON) V+ = 5.5V, VCOM = 1V, 4.5V, Note 7 25 - 1.5 2 Ω Full - - 5 Ω 25 - 12 16 Ω Full - - 20 Ω 25 -1 0.01 1 nA nA Full -5 - 5 25 -1 0.01 1 nA Full -5 - 5 nA 25 -2 - 2 nA Full -10 - 10 nA Input Voltage High, VINH Full 2.4 1.6 - V Input Voltage Low, VINL Full - 1.6 0.8 V V+ = 5.5V, VIN = 0V or V+ Full -0.5 0.03 0.5 µA Turn-ON Time, tON V+ = 4.5V, VNO or VNC = 3V, RL = 300Ω, CL = 35pF, VIN = 0 to 3V, See Figure 1 25 - 50 100 ns Full - - 150 ns Turn-OFF Time, tOFF V+ = 4.5V, VNO or VNC = 3V, RL = 300Ω, CL = 35pF, VIN = 0 to 3V, See Figure 1 25 - 20 50 ns Full - - 75 ns Full 10 30 - ns DIGITAL INPUT CHARACTERISTICS Input Current, IINH, IINL DYNAMIC CHARACTERISTICS Break-Before-Make Time Delay (ISL43142), tD V+ = 5.5V, VNO or VNC = 3V, RL = 300Ω, CL = 35pF, VIN = 0 to 3V, See Figure 3 Charge Injection, Q CL = 1.0nF, VG = 0V, RG = 0Ω, See Figure 2 25 - 1 5 pC OFF Isolation RL = 50Ω, CL = 15pF, f = 100kHz, VNO or VNC = 1VRMS, See Figures 4, 6, and 19 25 - >90 - dB 25 - <-90 - dB Crosstalk, Note 9 6 ISL43140, ISL43141, ISL43142 Electrical Specifications: 5V Supply PARAMETER Test Conditions: V+ = +4.5V to +5.5V, V- = GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 5), Unless Otherwise Specified (Continued) TEST CONDITIONS TEMP (oC) MIN (NOTE 6) TYP MAX (NOTE 6) UNITS All Hostile Crosstalk RL = 50Ω, CL = 15pF, f = 10MHz, VNO or VNC = 1VRMS, See Figure 19 25 - -60 - dB Power Supply Rejection Ratio RL = 50Ω, CL = 15pF, f = 1MHz, See Figure 20 25 - 60 - dB NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 7 - pF COM OFF Capacitance, CCOM(OFF) f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 7 - pF COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 14 - pF POWER SUPPLY CHARACTERISTICS V+ = 5.5V, VIN = 0V or V+, Switch On or Off Positive Supply Current, I+ Negative Supply Current, I- Electrical Specifications: 3V to 3.3V Supply PARAMETER 25 -1 0.05 1 µA Full -1 - 1 µA 25 -1 0.05 1 µA Full -1 - 1 µA Test Conditions: V+ = +2.7V to +3.6V, V- = GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 5), Unless Otherwise Specified TEST CONDITIONS TEMP (oC) MIN (NOTE 6) TYP Full 0 - 25 - Full - MAX (NOTE 6) UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG V+ = 2.7V, ICOM = 1.0mA, VNO or VNC = 1V, See Figure 5 ON Resistance, RON RON Matching Between Channels, ∆RON V+ = 2.7V, ICOM = 1.0mA, VNO or VNC = 1V RON Flatness, RFLAT(ON) V+ = 2.7V, ICOM = 1.0mA, VNO or VNC = 0.5V to 1.5V, Note 8 NO or NC OFF Leakage Current, INO(OFF) or INC(OFF) V+ = 3.6V, VCOM = 1V, 2.6V, VNO or VNC = 2.6V, 1V, Note 7 COM OFF Leakage Current, ICOM(OFF) V+ = 3.6V, VCOM = 1V, 2.6V, VNO or VNC = 2.6V, 1V, Note 7 COM ON Leakage Current, ICOM(ON) V+ = 3.6V, VCOM = 1V, 2.6V, Note 7 V+ V 200 250 Ω - 270 Ω 25 - 2 4 Ω Full - - 6 Ω 25 - 80 100 Ω Full - - 120 Ω 25 -1 0.01 1 nA Full -5 - 5 nA 25 -1 0.01 1 nA Full -5 - 5 nA 25 -2 - 2 nA Full -10 - 10 nA Input Voltage High, VINH Full 2.4 1.6 - V Input Voltage Low, VINL Full - 1.6 0.8 V V+ = 3.6V, VIN = 0V or V+ Full -0.5 0.03 0.5 µA Turn-ON Time, tON V+ = 2.7V, VNO or VNC = 1.5V, RL = 300Ω, CL = 35pF, VIN = 0 to V+, See Figure 1 25 - 120 180 ns Full - - 220 ns Turn-OFF Time, tOFF V+ = 2.7V, VNO or VNC = 1.5V, RL = 300Ω, CL = 35pF, VIN = 0 to V+, See Figure 1 25 - 25 45 ns Full - - 60 ns 25 15 50 - ns DIGITAL INPUT CHARACTERISTICS Input Current, IINH, IINL DYNAMIC CHARACTERISTICS Break-Before-Make Time Delay (ISL43142), tD V+ = 3.6V, VNO or VNC = 1.5V, RL = 300Ω, CL = 35pF, VIN = 0 to 3V, See Figure 3 Charge Injection, Q CL = 1.0nF, VG = 0V, RG = 0Ω, See Figure 2 25 - 0.5 5 pC OFF Isolation RL = 50Ω, CL = 15pF, f = 100kHz, VNO or VNC = 1VRMS, See Figures 4, 6, and 19 25 - >90 - dB 25 - <-90 - dB All Hostile Crosstalk RL = 50Ω, CL = 15pF, f = 10MHz, VNO or VNC = 1VRMS, See Figure 19 25 - -60 - dB Power Supply Rejection Ratio RL = 50Ω, CL = 15pF, f = 1MHz, See Figure 20 25 - 60 - dB Crosstalk, Note 9 7 ISL43140, ISL43141, ISL43142 Electrical Specifications: 3V to 3.3V Supply Test Conditions: V+ = +2.7V to +3.6V, V- = GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 5), Unless Otherwise Specified (Continued) TEMP (oC) MIN (NOTE 6) TYP NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 7 - pF COM OFF Capacitance, CCOM(OFF) f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 7 - pF COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 14 - pF 25 -1 0.05 1 µA PARAMETER TEST CONDITIONS MAX (NOTE 6) UNITS POWER SUPPLY CHARACTERISTICS V+ = 3.6V, VIN = 0V or V+, Switch On or Off Positive Supply Current, I+ Negative Supply Current, I- Full -1 - 1 µA 25 -1 0.05 1 µA Full -1 - 1 µA Test Circuits and Waveforms V+ tr < 20ns tf < 20ns 3V LOGIC INPUT 50% 0V C tOFF SWITCH VNX INPUT VOUT NO or NC VNX COM VOUT IN 90% SWITCH OUTPUT C SWITCH INPUT 90% RL 300Ω GND 0V LOGIC INPUT tON V- Logic input waveform is inverted for switches that have the opposite logic sense. CL 35pF C Repeat test for all switches. CL includes fixture and stray capacitance. RL V OUT = V (NO or NC) -----------------------------R +R L ( ON ) FIGURE 1B. TEST CIRCUIT FIGURE 1A. MEASUREMENT POINTS FIGURE 1. SWITCHING TIMES V+ SWITCH OUTPUT VOUT ∆VOUT RG NO or NC C VOUT COM 3V LOGIC INPUT ON ON VG OFF GND 0V C Q = ∆VOUT x CL V- Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 2A. MEASUREMENT POINTS CL LOGIC INPUT Repeat test for all switches. CL includes fixture and stray capacitance. FIGURE 2B. TEST CIRCUIT FIGURE 2. CHARGE INJECTION 8 IN ISL43140, ISL43141, ISL43142 Test Circuits and Waveforms (Continued) V+ C C 3V LOGIC INPUT 0V VOUT1 NO1 VNX COM1 VOUT2 RL1 300Ω NC2 COM2 IN1 90% 90% SWITCH OUTPUT VOUT1 0V RL2 300Ω IN2 90% SWITCH OUTPUT VOUT2 0V 90% LOGIC INPUT CL2 35pF GND C tD tD CL1 35pF V- CL includes fixture and stray capacitance. Reconfigure accordingly to test SW3 and SW4. FIGURE 3A. MEASUREMENT POINTS FIGURE 3B. TEST CIRCUIT FIGURE 3. BREAK-BEFORE-MAKE TIME (ISL43142 ONLY) V+ V+ C C RON = V1/1mA SIGNAL GENERATOR NO or NC NO or NC VNX 0V or 2.4V IN 1mA COM ANALYZER 0.8V or 2.4V IN V1 COM GND GND RL C C V- V- Repeat test for all switches. Repeat test for all switches. FIGURE 5. RON TEST CIRCUIT FIGURE 4. OFF ISOLATION TEST CIRCUIT V+ V+ C SIGNAL GENERATOR NO1 or NC1 50Ω COM1 NO or NC IN1 IN 0V or 2.4V IN2 0V or 2.4V COM2 ANALYZER NO CONNECTION NO2 or NC2 GND 0V or 2.4V IMPEDANCE ANALYZER COM GND RL C V- FIGURE 6. CROSSTALK TEST CIRCUIT 9 V- FIGURE 7. CAPACITANCE TEST CIRCUIT ISL43140, ISL43141, ISL43142 Detailed Description Power-Supply Considerations The ISL43140–ISL43142 quad analog switches offer precise switching capability from a bipolar ±2V to ±6V or a single 2V to 12V supply with low on-resistance (50Ω) and high speed switching (tON = 40ns, tOFF = 15ns). The devices are especially well suited to portable battery powered equipment thanks to the low operating supply voltage (2V), low power consumption (1µW), low leakage currents (1nA max), and the tiny QFN packaging. High frequency applications also benefit from the wide bandwidth, and the very high off isolation and crosstalk rejection. The ISL4314X construction is typical of most CMOS analog switches, in that they have three supply pins: V+, V-, and GND. V+ and V- drive the internal CMOS switches and set their analog voltage limits, so there are no connections between the analog signal path and GND. Unlike switches with a 13V maximum supply voltage, the ISL4314X 15V maximum supply voltage provides plenty of room for the 10% tolerance of 12V supplies (±6V or 12V single supply), as well as room for overshoot and noise spikes. Supply Sequencing And Overvoltage Protection With any CMOS device, proper power supply sequencing is required to protect the device from excessive input currents which might permanently damage the IC. All I/O pins contain ESD protection diodes from the pin to V+ and to V- (see Figure 8). To prevent forward biasing these diodes, V+ and V- must be applied before any input signals, and input signal voltages must remain between V+ and V-. If these conditions cannot be guaranteed, then one of the following two protection methods should be employed. Logic inputs can easily be protected by adding a 1kΩ resistor in series with the input (see Figure 8). The resistor limits the input current below the threshold that produces permanent damage, and the sub-microamp input current produces an insignificant voltage drop during normal operation. Adding a series resistor to the switch input defeats the purpose of using a low RON switch, so two small signal diodes can be added in series with the supply pins to provide overvoltage protection for all pins (see Figure 8). These additional diodes limit the analog signal from 1V below V+ to 1V above V-. The low leakage current performance is unaffected by this approach, but the switch resistance may increase, especially at low supply voltages. This family of switches performs equally well when operated with bipolar or single voltage supplies. The addition of the GND pin allows for asymmetrical bipolar supplies (e.g. +5V and -3V). The minimum recommended supply voltage is 2V or ±2V. It is important to note that the input signal range, switching times, and on-resistance degrade at lower supply voltages. Refer to the electrical specification tables and Typical Performance Curves for details. V+ and GND power the internal logic (thus setting the digital switching point) and level shifters. The level shifters convert the logic levels to switched V+ and V- signals to drive the analog switch gate terminals, so switch parameters especially RON - are strongly influenced by V-. Logic-Level Thresholds V+ and GND power the internal logic stages, so V- has no affect on logic thresholds. This switch family is TTL compatible (0.8V and 2.4V) over a V+ supply range of 2.5V to 10V (see Figure 17). At 12V the VIH level is about 2.7V, so for best results use a logic family the provides a VOH greater than 3V. The digital input stages draw supply current whenever the digital input voltage is not at one of the supply rails. Driving the digital input signals from GND to V+ with a fast transition time minimizes power dissipation. High-Frequency Performance OPTIONAL PROTECTION DIODE V+ OPTIONAL PROTECTION RESISTOR INX VNO or NC VCOM VOPTIONAL PROTECTION DIODE FIGURE 8. OVERVOLTAGE PROTECTION 10 In 50Ω systems, signal response is reasonably flat even past 100MHz (see Figure 18). Figure 18 also illustrates that the frequency response is very consistent over a wide V+ range, and for varying analog signal levels. An off switch acts like a capacitor and passes higher frequencies with less attenuation, resulting in signal feedthrough from a switch’s input to its output. Off Isolation is the resistance to this feedthrough, while Crosstalk indicates the amount of feedthrough from one switch to another. Figure 19 details the high Off Isolation and Crosstalk rejection provided by this family. At 10MHz, off isolation is about 50dB in 50Ω systems, decreasing approximately 20dB per decade as frequency increases. Higher load impedances decrease Off Isolation and Crosstalk rejection due to the voltage divider action of the switch OFF impedance and the load impedance. ISL43140, ISL43141, ISL43142 Leakage Considerations Reverse ESD protection diodes are internally connected between each analog-signal pin and both V+ and V-. One of these diodes conducts if any analog signal exceeds V+ or V-. Virtually all the analog leakage current comes from the ESD diodes to V+ or V-. Although the ESD diodes on a given signal pin are identical and therefore fairly well balanced, they are reverse biased differently. Each is biased by either V+ or V- and the analog signal. This means their leakages will vary as the signal varies. The difference in the two diode leakages to the V+ and V- pins constitutes the analog-signalpath leakage current. All analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal. This is why both sides of a given switch can show leakage currents of the same or opposite polarity. There is no connection between the analog signal paths and GND. Typical Performance Curves TA = 25oC, Unless Otherwise Specified 100 90 80 70 60 50 40 120 V- = -5V 85oC 25oC -40oC 25oC -40oC 40 300 250 200 150 100 50 0 RON (Ω) 60 25oC -40oC 2 3 4 5 6 7 8 V+ (V) 150 25oC 100 -40oC V+ = 3V 9 10 11 12 13 V+ = 5V 95 25oC V- = 0V 75 -40oC 25oC V- = 0V -40oC 0 1 2 3 4 5 6 7 VCOM (V) 8 9 10 11 12 5 VS = ±2V ICOM = 1mA V+ = 12V 85oC FIGURE 10. ON RESISTANCE vs SWITCH VOLTAGE FIGURE 9. ON RESISTANCE vs POSITIVE SUPPLY VOLTAGE 180 ICOM = 1mA V- = 0V 85oC 55 80 70 60 50 40 30 20 V- = 0V 85oC 85oC 115 85oC 80 200 50 135 V- = -3V 100 RON (Ω) 250 VCOM = (V+) - 1V ICOM = 1mA 140 85oC 25oC 2.5 100 -40oC V+ = 12V V+ = 3V 0 VS = ±3V 100 85oC 80 25oC 60 -40oC Q (pC) RON (Ω) 60 120 -2.5 V+ = 5V VS = ±5V -5 40 90 VS = ±5V 85oC 70 -7.5 25oC 50 -40oC 30 -5 -4 -3 -2 -1 0 1 2 3 4 VCOM (V) FIGURE 11. ON RESISTANCE vs SWITCH VOLTAGE 11 -10 5 -5 -2.5 0 2.5 5 VCOM (V) 7.5 10 12.5 FIGURE 12. CHARGE INJECTION vs SWITCH VOLTAGE ISL43140, ISL43141, ISL43142 Typical Performance Curves TA = 25oC, Unless Otherwise Specified (Continued) 50 300 VCOM = (V+) - 1V VCOM = (V+) - 1V V- = 0V V- = 0V 250 40 tOFF (ns) tON (ns) 200 150 85oC 30 85oC 25oC 100 25oC 20 -40oC -40oC 50 0 10 2 3 4 5 6 7 8 9 10 11 12 2 3 4 5 6 7 V+ (V) FIGURE 13. TURN - ON TIME vs POSITIVE SUPPLY VOLTAGE 25oC 100 tOFF (ns) 0 250 V- = -3V 25oC 25 85oC -40oC 0 300 V- = -3V -40oC 150 25oC 100 85oC 50 -40oC 2 25oC 200 150 0 12 VCOM = (V+) - 1V V- = -5V 250 -40oC 50 11 85oC 50 -40oC 100 10 75 85oC 200 -40oC 100 25oC 50 tON (ns) 125 VCOM = (V+) - 1V V- = -5V -40oC 150 9 FIGURE 14. TURN - OFF TIME vs POSITIVE SUPPLY VOLTAGE 250 200 8 V+ (V) 3 4 5 6 7 V+ (V) 8 9 10 11 12 FIGURE 15. TURN - ON TIME vs POSITIVE SUPPLY VOLTAGE 85oC 0 2 3 4 5 6 7 V+ (V) 8 9 10 11 12 FIGURE 16. TURN - OFF TIME vs POSITIVE SUPPLY VOLTAGE NORMALIZED GAIN (dB) 3.5 V- = 0V to -5V 3 -40oC 2.5 85oC VINH 2 VS = ±2V (VIN = 3VP-P) or V+ = 5V (VIN = 4VP-P) 0 VS = ±5V (VIN = 5VP-P) GAIN -3 V+ = 2.7V (VIN = 2VP-P) 0 -40oC PHASE VS = ±2V (VIN = 3VP-P) V+ = 5V (VIN = 4VP-P) VS = ±5V (VIN = 5VP-P) 25oC 1.5 VINL 1 45 90 135 85oC 180 RL = 50Ω 0.5 2 3 4 5 6 7 8 9 10 V+ (V) FIGURE 17. DIGITAL SWITCHING POINT vs POSITIVE SUPPLY VOLTAGE 12 11 12 1 10 100 FREQUENCY (MHz) FIGURE 18. FREQUENCY RESPONSE 600 PHASE (DEGREES) VINH AND VINL (V) 25oC V+ = 2.7V (VIN = 2VP-P) 3 ISL43140, ISL43141, ISL43142 Typical Performance Curves TA = 25oC, Unless Otherwise Specified (Continued) 10 -10 0 20 10 30 40 -50 50 -60 60 ISOLATION CROSSTALK -70 70 -80 80 -90 ALL HOSTILE CROSSTALK -100 -110 1k 10k 100k 1M 10M FREQUENCY (Hz) FIGURE 19. CROSSTALK AND OFF ISOLATION Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): VTRANSISTOR COUNT: ISL43140: 188 ISL43141: 188 ISL43142: 188 PROCESS: Si Gate CMOS 13 VIN = 1VP-P 30 40 -PSRR, SWITCH ON 50 60 -PSRR, SWITCH OFF 90 70 100 80 110 100M 500M V+ = 3V to 12V or VS = ±2V to ±5V RL = 50Ω 20 PSRR (dB) -40 OFF ISOLATION (dB) CROSSTALK (dB) V+ = 3V to 12V or -20 VS = ±2V to ±5V RL = 50Ω -30 +PSRR, SWITCH OFF +PSRR, SWITCH ON 0.3 1 10 100 FREQUENCY (MHz) FIGURE 20. ±PSRR vs FREQUENCY 1000 ISL43140, ISL43141, ISL43142 Small Outline Plastic Packages (SOIC) N INDEX AREA 0.25(0.010) M H M16.15 (JEDEC MS-012-AC ISSUE C) 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M E -B1 2 INCHES 3 L SEATING PLANE -A- h x 45o A D -C- µα e A1 B 0.25(0.010) M C 0.10(0.004) C A M B S NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 14 MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.3859 0.3937 9.80 10.00 3 E 0.1497 0.1574 3.80 4.00 4 e 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N α 16 0o 16 8o 0o 7 8o Rev. 0 12/93 ISL43140, ISL43141, ISL43142 Thin Shrink Small Outline Plastic Packages (TSSOP) N M16.173 INDEX AREA E 0.25(0.010) M 2 16 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE E1 GAUGE PLANE -B1 B M INCHES 3 L 0.05(0.002) -A- A D -C- α e A2 A1 b 0.10(0.004) M 0.25 0.010 SEATING PLANE c 0.10(0.004) C A M B S NOTES: SYMBOL MIN MAX MIN MAX NOTES A - 0.047 - 1.20 - A1 0.002 0.006 0.05 0.15 - A2 0.031 0.051 0.80 1.05 - b 0.0075 0.0118 0.19 0.30 9 c 0.0035 0.0079 0.09 0.20 - D 0.193 0.201 4.90 5.10 3 E1 0.169 0.177 4.30 4.50 4 e 0.026 BSC E 0.246 L 0.0177 N 1. These package dimensions are within allowable dimensions of JEDEC MO-153-AB, Issue E. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E1” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. (Angles in degrees) 15 MILLIMETERS α 0.65 BSC 0.256 6.25 0.0295 0.45 16 0o - 0.75 6 16 8o 0o - 6.50 7 8o Rev. 0 6/98 ISL43140, ISL43141, ISL43142 Quad Flat No-Lead Plastic Package (QFN) Micro Lead Frame Plastic Package (MLFP) L16.3x3 16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220VEED-2 ISSUE C) MILLIMETERS SYMBOL MIN NOMINAL MAX NOTES A 0.80 0.90 1.00 - A1 - - 0.05 - A2 - - 1.00 9 A3 b 0.20 REF 0.18 D 0.30 5, 8 3.00 BSC D1 D2 0.23 9 - 2.75 BSC 1.35 1.50 9 1.65 7, 8 E 3.00 BSC - E1 2.75 BSC 9 E2 1.35 e 1.50 1.65 7, 8 0.50 BSC - k 0.25 - - - L 0.30 0.40 0.50 8 L1 - - 0.15 10 N 16 2 Nd 4 3 Ne 4 3 P - - 0.60 9 θ - - 12 9 Rev. 0 10/02 NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on each D and E. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Features and dimensions A2, A3, D1, E1, P & θ are present when Anvil singulation method is used and not present for saw singulation. 10. Depending on the method of lead termination at the edge of the package, a maximum 0.15mm pull back (L1) maybe present. L minus L1 to be equal to or greater than 0.3mm. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16