NEC EXPRESS5800/T120b-E Configuration Guide Introduction This document contains product and configuration information that will enable you to configure your system. The guide will ensure fast and proper configuration of your NEC EXPRESS5800 server. February 2012 Revision 4.3 NEC Corporation CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Contents TECHNICAL SPECIFICATION ........................................................................................ 3 Key Features .......................................................................................................................................... 3 Specification .......................................................................................................................................... 3 EXTERNAL VIEWS ......................................................................................................... 5 Front and Rear Views ........................................................................................................................... 5 Dimensions (mm) .................................................................................................................................. 6 CONFIGURATION DIAGRAM ......................................................................................... 7 SERVER CONFIGURATION ........................................................................................... 8 1 2 3 Base Models ................................................................................................................................... 8 2nd Processor ................................................................................................................................ 8 Memory ........................................................................................................................................... 9 3.1 Memory Configuration ........................................................................................................... 9 4 Internal Hard Disk Drives ............................................................................................................ 12 4.1 RAID Configuration .............................................................................................................. 12 4.2 Internal Drive Configuration ................................................................................................. 13 5 Optical Drive ................................................................................................................................. 24 6 Internal Tape / RDX Drives .......................................................................................................... 25 6.1 Tape / RDX Drive Selection ................................................................................................. 25 6.2 Tape / RDX Configuration .................................................................................................... 26 7 PCI Card ........................................................................................................................................ 28 7.1 LAN Controller ..................................................................................................................... 28 7.2 External RAID Controller ..................................................................................................... 29 7.3 SAS Controller ..................................................................................................................... 29 7.4 Serial Port Adapter .............................................................................................................. 29 8 Other Add-in Components .......................................................................................................... 30 8.1 Power Supply ...................................................................................................................... 30 8.2 Redundant Fan .................................................................................................................... 30 8.3 VMware ESXi Pre-install Kit ................................................................................................ 30 8.4 Input Devices ....................................................................................................................... 30 9 Add-on Components ................................................................................................................... 30 9.1 Rack Conversion Kit ............................................................................................................ 30 9.2 Flash FDD............................................................................................................................ 30 9.3 Server Management License............................................................................................... 31 9.4 Medium and Cartridge ......................................................................................................... 31 10 Support Service .......................................................................................................................... 31 10.1 Software ............................................................................................................................ 31 REFERENCES............................................................................................................... 32 Server Management ............................................................................................................................ 32 OS Support Matrix for PCI Cards ...................................................................................................... 33 Supporting PCI Cards and Installable Slots ..................................................................................... 34 Copyright Notice and Liability Disclaimer ........................................................................................ 35 REVISION HISTORY ..................................................................................................... 36 NEC Corporation Revision 4.3, February 2012 2 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Technical Specification Key Features High performance with the latest Intel® Xeon® processor 5600 series Up to 192 GB of high speed DDR3-1333 memory High energy efficiency with power capping feature and 80 PLUS® Silver power supply Full manageability by integrated EXPRESSSCOPE Engine 2 Specification Model T120b-E Part Number Processor N8100-1731F N8100-1732F N8100-1733F N8100-1734F Type Intel® Xeon® processor E5606 Intel® Xeon® processor E5620 Intel® Xeon® processor E5645 Intel® Xeon® processor X5650 Clock speed 2.13 GHz 2.40 GHz 2.40 GHz 2.66 GHz Number of Processors 1 or 2 Cache 8 MB 12 MB 12 MB 12 MB Cores and Threads 4C-4T 4C-8T 6C-12T 6C-12T Chipset Memory Internal Storage Expansion Slots [free] Intel® 5520 Chipset Type DDR3-1333 and DDR3-1066 ECC Registered Low Power DIMM Standard Capacity 0 GB Maximum Capacity 192 GB (12 x 16 GB) Memory protection ECC, x4 SDDC, Memory Mirroring, Memory Lockstep, Memory Sparing Standard Capacity 0 GB Maximum Capacity 2.5-inch drive configuration: SAS : 7.2 TB (8 x 900 GB) SATA : 8 TB (8 x 1 TB) SSD : 800 GB ( 8 x 100 GB) 3.5-inch drive configuration: SATA : 12 TB (4 x 3 TB) Disk Controller SATA : 3Gb/s (Integrated) SAS: 6Gb/s (Optional) RAID SATA : RAID 0/1 (Standard), RAID 5/6/50 (Optional) SAS : RAID 0/1/5/6/10/50 (Optional) Hot Plug Supported Optical Disk Drive DVD-ROM 5-inch Media Bays [free] Disk Drive Bays [free] 3 [2] Standard Total: 6 slots available 4[4] x PCIe 2.0 x8 (x8 connector) 1[1] x PCIe x4 (x8 connector) 1[1] x 32-bit / 33 MHz 5V PCI Video Controller (VRAM) Interfaces NEC Corporation 1 2 2.5-inch drive configuration: 8 [8] 3.5-inch drive configuration: 4 [4] Integrated in Server Management Controller (32MB) 1 x Keyboard (6-pin mini DIN, 1 x rear) 1 x Mouse (6-pin mini DIN, 1 x rear) 1 x VGA (15-pin mini D-sub, 1 x rear) 1 x Serial (9-pin mini D-sub, RS232-C, 1 x rear) Revision 4.3, February 2012 3 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Model T120b-E Interfaces (Cont.) 8 x USB2.0 (2 x front, 2 x rear, 4 x internal) 2 x 1000BASE-T LAN connector (1000BASE-T / 100BASE-TX / 10BASE-T, RJ-45, 2 x rear) 1 x Management LAN connector (100BASE-TX / 10BASE-T, RJ-45, 1 x rear) Server Management EXPRESSSCOPE Engine 2 Redundant Fan Optional, non-hot plug Redundant Power Supply Optional, hot plug Power Supply Non-hot plug power supply configuration: 665 Watt 80 PLUS® certified non-hot plug PSU Hot plug power supply configuration: 1-2 x 600 Watt 80 PLUS® Silver certified hot plug PSU 100-240 VAC ± 10% 50 / 60 Hz ± 3 Hz Power Consumption (Max. Config, Idling) 225 VA / 223 Watt 227 VA / 225 Watt 228 VA / 225 Watt 229 VA / 227 Watt (Max. Config, Operating) 398 VA / 394 Watt 432 VA / 427 Watt 457 VA / 452 Watt 500 VA / 495 Watt Acoustical Noise Max. Config, Idling (Sound Pressure Max. Config, Operating 3 Level) Dimensions (W x D x H ) 44.2 dB Weight (Minimum / Maximum) 20 kg / 26 kg, 44.09 lbs. / 57.32 lbs. Temperature, Relative Humidity (non-condensing) Operating: 10° to 35° C / 50° to 95° F, 20 to 80% Non-operating: -10° to 55° C / 14° to 131° F, 20 to 80% Regulatory and Safety FCC, CE, BSMI, CCC, UL, CB, RoHS, WEEE Operating Systems Microsoft® Windows Server® 2003, Standard Edition (SP1 or later) Microsoft® Windows Server® 2003, Enterprise Edition (SP1 or later) Microsoft® Windows Server® 2003 R2, Standard Edition Microsoft® Windows Server® 2003 R2, Enterprise Edition Microsoft® Windows Server® 2003 R2, Standard x64 Edition Microsoft® Windows Server® 2003 R2, Enterprise x64 Edition Microsoft® Windows Server® 2008 Standard Microsoft® Windows Server® 2008 Enterprise Microsoft® Windows Server® 2008 Standard (x64) Microsoft® Windows Server® 2008 Enterprise (x64) Microsoft® Windows Server® 2008 R2 Standard Microsoft® Windows Server® 2008 R2 Enterprise 4 Red Hat Enterprise Linux ES4.8 or later (x86) 4 Red Hat Enterprise Linux ES4.8 or later (EM64T) 4 Red Hat Enterprise Linux AS4.8 or later (x86) 4 Red Hat Enterprise Linux AS4.8 or later (EM64T) 4 Red Hat Enterprise Linux 5.4 or later (x86) 4 Red Hat Enterprise Linux 5.4 or later (EM64T) 4 Red Hat Enterprise Linux Advanced Platform5.4 or later (x86) 4 Red Hat Enterprise Linux Advanced Platform5.4 or later (EM64T) 4 Red Hat Enterprise Linux 6.0 or later (x86) 4 Red Hat Enterprise Linux 6.0 or later (x86_64) VMware ESXi 4.1 1 2 3 4 45.0 dB 205.0 x 599.0 x 450.0 mm / 8.1 x 23.6 x 17.7 in (5U) On-board SATA RAID controller is supported only on Windows operating systems. RAID 10 configured with 2 TB HDDs is not supported on the on-board SATA Controller. Noise emission was measured in accordance with ISO 7779. The actual value may vary by the operating environment. For Linux support, contact our sales representative or go to the NEC website at: http://www.nec.com/global/prod/express/linux/index.html NEC Corporation Revision 4.3, February 2012 4 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E External Views Front and Rear Views Front View A A F G H I J K B C D F G H I J K B C D E E L L 2.5-inch Drive Configuration 3.5-inch Drive Configuration Legend A. 5-inch Media Bay G. Data LAN 2 Activity LED B. DVD-ROM Drive H. Power LED C. Dump (NMI) Switch I. Power Button D. System Reset Switch J. Data LAN 1 Activity LED E. Drive Cage Bays K. Hard Drive Activity LED F. System Status LED L. USB Connectors NEC Corporation Revision 4.3, February 2012 5 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Rear View A B C D E F I G H Legend A. Mouse Connector F. USB Connectors B. Keyboard Connector G. Data LAN Connectors C. Serial Port B Connector H. PCI Slots D. VGA Connector I. Power Supply Bay E. Management LAN Connector Dimensions (mm) Non-hot Plug Power Supply Configuration 620.0 599.0 205.0 450.0 316.0 NEC Corporation Revision 4.3, February 2012 6 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Hot Plug Power Supply Configuration 629.0 599.0 450.0 205.0 316.0 Configuration Diagram CHASSIS REAR Media Bay #1 Power Supply Bays CHASSIS FRONT Media Bay #2 #1 #2 #3 #4 #5 #6 Processor #1 Legend: NEC Corporation DIMM #7 DIMM #8 DIMM #9 DIMM #10 DIMM #11 DIMM #12 Media Bay #3 (DVD-ROM) Cooling Fan #1 PCIe 2.0 x8 (x8 socket) FH PCIe 2.0 x8 (x8 socket) FH/HL PCIe 2.0 x8 (x8 socket) FH/HL PCIe 2.0 x8 (x8 socket) FH/HL PCIe x4 (x8 socket) FH/HL PCI 32-bit/33MHz FH/FL Processor #2 Cooling Fan #2 Cooling Fan #3 Cooling Fan #4 DIMM DIMM DIMM DIMM DIMM DIMM Minimum required components Revision 4.3, February 2012 Drive Cage Bays BBU slot #1 / #2 Standard components 7 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Server Configuration 1 Base Models Product Name / Description Part Number NEC EXPRESS5800/T120b-E Server (4C/E5606) no RAM, no Drive Cage, no HDD, no PSU Including: 1 x Intel Xeon processor E5606, DVD-ROM drive, EXPRESSBUILDER DVD NEC EXPRESS5800/T120b-E Server (4C/E5620) no RAM, no Drive Cage, no HDD, no PSU Including: 1 x Intel Xeon processor E5620, DVD-ROM drive, EXPRESSBUILDER DVD NEC EXPRESS5800/T120b-E Server (6C/E5645) no RAM, no Drive Cage, no HDD, no PSU Including: 1 x Intel Xeon processor E5645, DVD-ROM drive, EXPRESSBUILDER DVD NEC EXPRESS5800/T120b-E Server (6C/X5650) no RAM, no Drive Cage, no HDD, no PSU Including: 1 x Intel Xeon processor X5650, DVD-ROM drive, EXPRESSBUILDER DVD N8100-1731F N8100-1732F N8100-1733F N8100-1734F 2 2nd Processor Available sockets: 1 Product Name / Description Part Number CPU Kit (4C/E5606) Intel® Xeon® Processor E5606 (2.13 GHz / 4C-4T / 8 MB) CPU Kit (4C/E5620) Intel® Xeon® Processor E5620 (2.40 GHz / 4C-8T / 12 MB) CPU Kit (6C/E5645) Intel® Xeon® Processor E5645 (2.40 GHz / 6C-12T / 12 MB) CPU Kit (6C/X5650) Intel® Xeon® Processor X5650 (2.66 GHz / 6C-12T / 12 MB) N8101-494 N8101-472 N8101-495 N8101-496 NOTE: The 2nd processor must be the same with what is used in the base model NEC Corporation Revision 4.3, February 2012 8 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 3 Memory 3.1 Memory Configuration Refer to the section in accordance with your memory configuration: Independent channel / Memory Sparing Configuration: Refer to 3.1.1 Memory Mirroring / Memory Lockstep Configuration: Refer to 3.1.2 3.1.1 Independent Channel / Memory Sparing Configuration Available slots: 6 per processor Product Name / Description Part Number Additional 2GB Memory Module (1x 2GB) 2 GB (1 x 2 GB) DDR3-1333 ECC Registered Low Power DIMM Additional 4GB Memory Module (1x 4GB) 4 GB (1 x 4 GB) DDR3-1333 ECC Registered Low Power DIMM Additional 8GB Memory Module (1x 8GB) 8 GB (1 x 8 GB) DDR3-1333 ECC Registered Low Power DIMM Additional 16GB Memory Module (1x 16GB) 16 GB (1 x 16 GB) DDR3-1066 ECC Registered Low Power DIMM N8102-430 N8102-431 N8102-382 N8102-383 NOTE: Minimum one memory kit per processor must be installed. It is recommended to install two or three identical memory kits for dual-channel or triple-channel symmetric memory configurations to increase memory transfer speed. 3.1.2 Memory Mirroring / Memory Lockstep Configuration Available slots: 4 per processor Product Name / Description Part Number Additional 4GB Memory Module (2x 2GB) 4 GB (2 x 2 GB) DDR3-1333 ECC Registered Low Power DIMM Additional 8GB Memory Module (2x 4GB) 8 GB (2 x 4 GB) DDR3-1333 ECC Registered Low Power DIMM Additional 16GB Memory Module (2x 8GB) 16 GB (2 x 8 GB) DDR3-1333 ECC Registered Low Power DIMM Additional 32GB Memory Module (2x 16GB) 32 GB (2 x 16 GB) DDR3-1066 ECC Registered Low Power DIMM N8102-393 N8102-394 N8102-395 N8102-396 NOTE: Minimum one memory kit per processor must be installed. NEC Corporation Revision 4.3, February 2012 9 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Memory Configuration Feature Comparison See the table below for feature comparisons of memory configurations supported. Independent Channel Memory Sparing Memory Lockstep Memory Mirroring Performance Best Better Better Good Data Protection No Multiple single bit error protection No Multiple single bit and multi bit error protection Data Correction ECC, x4 SDDC ECC, x4 SDDC ECC, x8 SDDC ECC, x4 SDDC Redundancy No Partly No Fully Available Memory Full physical memory Physical memory excluding spare memory Full physical memory Half physical memory Available Memory Channels Notes 3 3 2 2 - All DIMMs in the system must be identical. Paired DIMMs must be identical. Paired DIMMs must be identical. Maximum Memory Speed See the table below for the actual maximum memory speed on your system. DDR3 memory speed depends on the type of DIMMs and the native memory bus speed of the memory controller. All memory buses operate at the clock frequency of the DIMM with the lowest frequency. Processor Type Memory Power Setting Populated DIMMs DIMMs per Channel DIMM Speed E5606 1 GB, 2 GB, 4 GB, 8 GB - - 1066 MHz E5620 16GB Normal (1.5V) 1 1066 MHz 2 800 MHz Low (1.35V) - 800 MHz Normal (1.5V) - 1333 MHz Low (1.35V) 1 1333 MHz 2 1066 MHz 1 1066 MHz 2 800 MHz - 800 MHz E5645 X5650 1 GB, 2 GB, 4 GB, 8 GB 16GB Normal (1.5V) Low (1.35V) NEC Corporation Revision 4.3, February 2012 10 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Maximum Available Memory See the table below for the maximum memory size that you can actually use on your system. The maximum available memory is less than the maximum physical memory supported by your system because some chipsets require PCI resource space of about 750MB. PCI resource requirements vary depending on the type and the number of PCI cards you are using. 1 Maximum Memory Size Supported by OS Maximum Available Memory 4 GB Microsoft Windows Server 2003, Standard Edition(SP1) Microsoft Windows Server 2003 R2, Standard Edition Microsoft Windows Server 2008 Standard 4 GB (HW-DEP enabled) App. 3.6 GB (HW-DEP disabled) 32 GB Microsoft Windows Server 2003 R2, Standard x64 Edition Microsoft Windows Server 2008 Standard (x64) Microsoft Windows Server 2008 R2 Standard (x64) 32 GB 64 GB Microsoft Windows Server 2003, Enterprise Edition(SP1) Microsoft Windows Server 2003 R2, Enterprise Edition Microsoft Windows Server 2008 Enterprise 64 GB 1 TB Microsoft Windows Server 2003 R2, Enterprise x64 Edition 192 GB 2 TB Microsoft Windows Server 2008 Enterprise (x64) Microsoft Windows Server 2008 R2 Enterprise (x64) 192 GB 16 GB Red Hat Enterprise Linux ES4 Red Hat Enterprise Linux ES4 (EM64T) Red Hat Enterprise Linux 5 Red Hat Enterprise Linux 5 Advanced Platform Red Hat Enterprise Linux 6 16 GB 64 GB Red Hat Enterprise Linux AS4 64 GB 256 GB Red Hat Enterprise Linux AS4 (EM64T) Red Hat Enterprise Linux 5 (EM64T) Red Hat Enterprise Linux 5 Advanced Platform (EM64T) 192 GB 2 TB Red Hat Enterprise Linux 6.0 (x86_64) 192 GB 256 GB 1 or 1TB VMware ESXi 4.1 192 GB Up to 255 GB of the main memory is available to each virtual machine. NEC Corporation Revision 4.3, February 2012 11 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4 Internal Hard Disk Drives 4.1 RAID Configuration Refer to the section in accordance with your disk form factor and RAID configuration. 4.1.1 Up to four 2.5-inch Drives Available Disk Refer to 4.2.1 SATA, SSD 128MB Cache Refer to 4.2.2 SAS, SATA, SSD 256MB Cache Refer to 4.2.3 SAS, SATA, SSD 256MB Cache Refer to 4.2.4 SAS, SATA, SSD 512MB Cache Refer to 4.2.5 SAS, SATA, SSD Non-RAID On-board SATA RAID Controller RAID 0/1/10 Optional RAID Controller RAID 5/6 NOTE: On-board SATA RAID controller is supported only on Windows operating systems. An optional RAID controller is required to configure RAID array for other operating systems. Hot plug insertion/removal is not supported with the on-board SATA non-RAID controller. All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. An optional RAID controller occupies one PCI slot. 4.1.2 Up to eight 2.5-inch Drives Available Disk RAID 0/1/10 RAID 5/6 128MB Cache Refer to 4.2.6 SAS, SATA, SSD 256MB Cache Refer to 4.2.7 SAS, SATA SSD 256MB Cache Refer to 4.2.8 SAS, SATA SSD 512MB Cache Refer to 4.2.9 SAS, SATA SSD NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. An optional RAID controller occupies one PCI slot. NEC Corporation Revision 4.3, February 2012 12 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.1.3 3.5-inch Drives Available Disk Refer to 4.2.10 SATA 128MB Cache Refer to 4.2.11 SATA 256MB Cache Refer to 4.2.12 SATA 256MB Cache Refer to 4.2.13 SATA 512MB Cache Refer to 4.2.14 SATA Non-RAID On-board SATA RAID Controller RAID 0/1/10 Optional RAID Controller RAID 5/6 NOTE: On-board SATA RAID controller is supported only on Windows operating systems. An optional RAID controller is required to configure RAID array for other operating systems. On-board SATA RAID Controller does not support RAID 10 configured with 2TB and 3TB HDDs. Hot plug insertion/removal is not supported with the on-board SATA non-RAID controller. All hard drives within a RAID array should be of the same capacity and rotation speed. An optional RAID controller occupies one PCI slot. 4.2 Internal Drive Configuration 4.2.1 2.5-inch Drive with On-board SATA Controller Category Product Name / Description Part Number Storage Controller On-board SATA Controller 4 x SATA ports, RAID 0/1/10 capable Internal SATA Cable 4 x Single SATA to 1 x mini-SAS 2.5-inch HDD Cage 8 x 2.5-inch hot plug hard drive bays 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 (Standard) Cable Required HDD Cage Required HDD 4 slots available SATA SSD K410-232(00) N8154-24 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: On-board SATA RAID controller is supported only on Windows operating systems. An optional RAID controller is required to configure RAID array for other operating systems. Hot plug insertion/removal is not supported with the on-board SATA non-RAID controller.. All hard drives within a RAID array should be of the same capacity and rotation speed. NEC Corporation Revision 4.3, February 2012 13 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.2 Up to four 2.5-inch Drives with RAID 0/1 Controller with 128 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (128MB, RAID 0/1) Promise SuperTrak TX8760T-128 RAID 0/1/10, 128MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 2.5-inch HDD Cage 8 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-128 RAID BBU Recommended Cable Required HDD Cage Required HDD SAS 4 slots available SATA SSD N8103-123 K410-174(00) N8154-24 N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 4.3, February 2012 14 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.3 Up to four 2.5-inch Drives with RAID 0/1 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1) LSI MegaRAID SAS 9264-8i RAID 0/1, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 2.5-inch HDD Cage 8 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-129 RAID BBU Recommended Cable Required HDD Cage Required HDD SAS 4 slots available SATA SSD N8103-123 K410-174(00) N8154-24 N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 4.3, February 2012 15 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.4 Up to four 2.5-inch Drives with RAID 5/6 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1/5/6) LSI MegaRAID SAS 9264-8i RAID 0/1/5/6/10/50, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 2.5-inch HDD Cage 8 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-130 RAID BBU Recommended Cable Required HDD Cage Required HDD SAS 4 slots available SATA SSD N8103-123 K410-174(00) N8154-24 N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 4.3, February 2012 16 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.5 Up to four 2.5-inch Drives with RAID 5/6 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (512MB, RAID0/1/5/6) Promise SuperTrak EX8760T-512 RAID 0/1/5/6/10/50, 512MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 2.5-inch HDD Cage 8 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-134 RAID BBU Recommended Cable Required HDD Cage Required HDD SAS 4 slots available SATA SSD N8103-140 K410-174(00) N8154-24 N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 4.3, February 2012 17 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.6 Up to eight 2.5-inch Drives with RAID 0/1 Controller with 128 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (128MB, RAID 0/1) Promise SuperTrak TX8760T-128 RAID 0/1/10, 128MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 2.5-inch HDD Cage 8 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-128 RAID BBU Recommended Cable 2 sets required HDD Cage Required HDD SAS 4 slots available SATA SSD N8103-123 K410-174(00) N8154-24 N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 4.3, February 2012 18 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.7 Up to eight 2.5-inch Drives with RAID 0/1 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1) LSI MegaRAID SAS 9264-8i RAID 0/1, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 2.5-inch HDD Cage 8 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-129 RAID BBU Recommended Cable 2 sets required HDD Cage Required HDD SAS 8 slots available SATA SSD N8103-123 K410-174(00) N8154-24 N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 4.3, February 2012 19 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.8 Up to eight 2.5-inch Drives with RAID 5/6 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1/5/6) LSI MegaRAID SAS 9264-8i RAID 0/1/5/6/10/50, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 2.5-inch HDD Cage 8 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-130 RAID BBU Recommended Cable 2 sets required HDD Cage Required HDD SAS 8 slots available SATA SSD N8103-123 K410-174(00) N8154-24 N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 4.3, February 2012 20 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.9 Up to eight 2.5-inch Drives with RAID 5/6 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (512MB, RAID0/1/5/6) Promise SuperTrak EX8760T-512 RAID 0/1/5/6/10/50, 512MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 2.5-inch HDD Cage 8 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-134 RAID BBU Recommended Cable 2 sets required HDD Cage Required HDD SAS 8 slots available SATA SSD N8103-140 K410-174(00) N8154-24 N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 4.3, February 2012 21 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.10 3.5-inch Drives with On-board SATA Controller Category Product Name / Description Part Number Storage Controller On-board SATA Controller 4 x SATA ports, RAID 0/1/10 capable Internal SATA Cable 4 x Single SATA to 1 x mini-SAS 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm (Standard) Cable Required HDD Cage Required HDD 4 slots available K410-232(00) N8154-27 N8150-386 N8150-387 N8150-388 N8150-263 N8150-278 NOTE: On-board SATA RAID controller is supported only on Windows operating systems. An optional RAID controller is required to configure RAID array for other operating systems. On-board SATA RAID Controller does not support RAID 10 configured with 2TB HDDs. Hot plug insertion/removal is not supported with the on-board SATA non-RAID controller. All hard drives within a RAID array should be of the same capacity and rotation speed. 4.2.11 3.5-inch Drives with RAID 0/1 Controller with 128 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (128MB, RAID 0/1) Promise SuperTrak TX8760T-128 RAID 0/1/10, 128MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm 3TB HDD 1 x 3 TB, 3.5-inch, SATA2, 7,200 rpm N8103-128 RAID BBU Recommended Cable Required HDD Cage Required HDD 4 slots available N8103-140 K410-174(00) N8154-27 N8150-386 N8150-387 N8150-388 N8150-263 N8150-278 N8150-337 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. NEC Corporation Revision 4.3, February 2012 22 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.12 3.5-inch Drives with RAID 0/1 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1) LSI MegaRAID SAS 9264-8i RAID 0/1, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm N8103-129 RAID BBU Recommended Cable Required HDD Cage Required HDD 4 slots available N8103-123 K410-174(00) N8154-27 N8150-386 N8150-387 N8150-388 N8150-263 N8150-278 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. 4.2.13 3.5-inch Drives with RAID 5/6 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1/5/6) LSI MegaRAID SAS 9264-8i RAID 0/1, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm N8103-130 RAID BBU Recommended Cable Required HDD Cage Required HDD 4 slots available N8103-123 K410-174(00) N8154-27 N8150-386 N8150-387 N8150-388 N8150-263 N8150-278 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. NEC Corporation Revision 4.3, February 2012 23 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 4.2.14 3.5-inch Drives with RAID 5/6 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (512MB, RAID0/1/5/6) Promise SuperTrak EX8760T-512 RAID 0/1/5/6/10/50, 512MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm 3TB HDD 1 x 3 TB, 3.5-inch, SATA2, 7,200 rpm N8103-134 RAID BBU Recommended Cable Required HDD Cage Required HDD 4 slots available N8103-140 K410-174(00) N8154-27 N8150-386 N8150-387 N8150-388 N8150-263 N8150-278 N8150-337 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. 5 Optical Drive Category Product Name / Description Part Number Internal 1 slot available Internal DVD-ROM drive DVD-ROM drive (Standard) NEC Corporation Revision 4.3, February 2012 24 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 6 Internal Tape / RDX Drives 6.1 Tape / RDX Drive Selection Refer to the section in accordance with your type of tape drives. DAT DAT72 USB Refer to 6.2.1 DAT160 USB Refer to 6.2.1 DAT320 USB Refer to 6.2.1 USB Refer to 6.2.2 LTO2 SAS Refer to 6.2.3 LTO3 SAS Refer to 6.2.3 LTO4 SAS Refer to 6.2.3 LTO5 SAS Refer to 6.2.4 RDX LTO NOTE: The same combination of drive type and host interface cannot be installed multiple times. Tape devices cannot be directly connected to VMware servers. For VMware systems, it is recommended to connect and configure an additional backup server via network. NEC Corporation Revision 4.3, February 2012 25 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 6.2 Tape / RDX Configuration 6.2.1 DAT / USB Category Product Name / Description Part Number Controller Internal USB Controller 1 x USB port Internal USB cable 1 x Internal USB to 1 x USB device NOTE: The cable is provided for each tape drive. (Standard) Internal DAT (USB) DDS3 / DDS4 / DAT72, Native capacity 36 GB NOTE: DDS1 / DDS2 format are not supported. N8151-69 Internal DAT (USB) DDS4 / DAT72 / DAT160, Native capacity 80 GB NOTE: DDS1 / DDS2 / DDS3 format are not supported. N8151-78 Internal DAT (USB) DAT160 / DAT 320, Native capacity 160 GB NOTE: DDS1 / DDS2 / DDS3 / DDS4 / DAT72 /DAT160 for WORM format are not supported. N8151-99 Category Product Name / Description Part Number Controller Internal USB Controller 1 x USB port Internal USB cable 1 x Internal USB to 1 x USB device NOTE: The cable is provided for each tape drive. (Standard) Internal RDX (USB) N8151-86 Cable Drive 2 bays available 6.2.2 RDX Cable Drive 2 bays available NEC Corporation (Standard) Revision 4.3, February 2012 (Standard) 26 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 6.2.3 LTO / SAS (1) Category Product Name / Description Part Number Controller Required SAS Controller LSI SAS3442E-R Host Bus Adapter 3Gbps SAS, Int. 4, Ext. 4, SFF-8484 / SFF8470, PCIe x8, LP/FH N8103-104A Cable Required Drive 2 bays available Internal SAS Cable 1x SFF-8484 SAS to 2x SFF-8482 SAS Internal LTO (SAS) LTO2, Half height, Native capacity 200 GB Internal LTO (SAS) LTO3, Half height, Native capacity 400 GB Internal LTO (SAS) LTO4, Half height, Native capacity 800 GB Internal LTO (SAS) LTO4, Full height, Native capacity 800 GB K410-173(00) 6.2.4 N8151-101 N8151-102 N8151-90 N8151-77 LTO / SAS (2) Category Product Name / Description Part Number Controller Required SAS Controller LSI ISAS9212-4i4 Host Bus Adapter 6Gbps SAS, Int. 4, Ext. 4, 7-pin SATA / SFF-8088, PCIe 2.0 x8, LP/FH Internal SAS Cable N8103-142 Cable Required Drive 2 bays available NEC Corporation K410-217(00) 1x 7-pin Single SATA to 1x SFF-8482 SAS Internal LTO (SAS) N8151-103 LTO5, Half height, Native capacity 1.5 TB Revision 4.3, February 2012 27 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 7 PCI Card 7.1 LAN Controller Category GbE PCIe PCI-X 10GbE Ctrlr Module Product Name / Description Part Number 1000BASE-T Adapter Intel® PRO/1000 PT Server Adapter PCIe x1, LP / FH 1000BASE-T Adapter (2ch) Intel® PRO/1000 PT Dual Port Server Adapter PCIe x4, FH 1000BASE-T Adapter (4ch) Intel® PRO/1000 PT Quad Port Server Adapter PCIe x4, LP / FH NOTE: Network cables with RJ-45 plug covers cannot be used. N8104-126 1000BASE-T Adapter Intel® PRO/1000 MT Server Adapter 64bit / 133 MHz PCI-X, FH 10GBASE-SR Adapter Chelsio S310E-SR 10GbE Storage Accelerator PCIe x8, LP / FH 10GBASE Adapter (SFP+/2ch) Broadcom NetXtreme II BCM957711 10G SFP+ Dual Port Network Interface Card PCIe 2.0 x8, LP / FH NOTE: - N8104-129 SFP+ Module is required to connect with an optical cable. - Up to 2 SFP+ Modules can be installed. - On Windows Server 2003R2 /2008 / 2008R2 and Red Hat Linux 5.x(EM64T) and 6.x(x86_64) operating systems, teaming and bonding features across one or two identical adapters are supported. A team can include up to two ports and up to two teams per system are allowed. - On Red Hat Linux 5.x(x86) and 6.x(x86) operating systems, bonding features within one adapter with up to two ports are supported. One team per system is allowed. N8104-119 SFP+ Module (10G-SR) 1 x SFP+ Module for N8104-128 N8104-129 N8104-121 N8104-125A N8104-123A N8104-128 NOTE: Teaming and bonding features across the standard LAN and optional PCIe based GbE LAN controller (excluding N8104-126) are supported on Windows Server 2003R2 /2008 / 2008R2 and Red Hat Linux 5.x operating systems. When installing a 1000BASE-SX Adapter, no other additional GbE LAN controllers is allowed. When installing a 10GBASE-SR Adapter, no other additional 10GbE LAN controllers is allowed. Teaming feature is not supported on iSCSI interfaces. NEC Corporation Revision 4.3, February 2012 28 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 7.2 External RAID Controller Category Product Name / Description Part Number Controller RAID Controller (512MB, RAID0/1/5/6) Promise SuperTrak EX8768 RAID 0/1/5/6/10/50, 512MB, Ext. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 N8103-135 RAID BBU 7.3 N8103-140 SAS Controller Category Product Name / Description Part Number SAS SAS Controller LSI SAS3442E-R Host Bus Adapter 3Gb/s SAS, Int. 4 / Ext. 4, SFF-8484 / SFF8470, PCIe x8, LP / FH SAS Controller LSI SAS9212-4i4 Host Bus Adapter 6Gb/s SAS, Int. 4 / Ext. 4, 7-pin SATA / SFF-8088, PCIe 2.0 x8, LP / FH N8103-104A 7.4 N8103-142 Serial Port Adapter Product Name / Description Part Number Serial port adapter Serial port fixed to PCI bracket N8117-01A NEC Corporation Revision 4.3, February 2012 29 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 8 Other Add-in Components 8.1 Power Supply Available slots: 1 slot Category Product Name / Description Part Number Non-hot Plug Power Supply Unit 1 x 665 Watt 80 PLUS® certified non-hot plug PSU Power Supply Unit 1x Power supply cage, 1 x 600 Watt 80 PLUS® Silver certified hot plug power supply module Power Supply 1 x 600 Watt 80 PLUS® Silver certified hot plug power supply module N8181-78F Hot Plug Main Power Module 8.2 N8181-71AF N8181-72AF Redundant Fan Product Name / Description Part Number Redundant Fan Cooling Fan for T120b-E N8181-67 8.3 VMware ESXi Pre-install Kit Product Name / Description Part Number VMware ESXi 4.1 Base Kit Including USB flash memory, VMware ESXi 4.1 Recovery CD NOTE: - The Base Kit may not be available in some regions. Please contact our sales representative to confirm if it is available in your country. - The Base Kit must be ordered with the base model. - Installation of VMware ESXi onto hard drives is not supported. N8106-004F 8.4 Input Devices Product Name / Description Part Number Keyboard and Mouse Pack (US) 1 x 104-keys White PS/2 keyboard, 1 x PS/2 White Optical Wheel Mouse (Standard) 9 Add-on Components 9.1 Rack Conversion Kit The following rack conversion kit is required to install the server into a 19-inch rack system: Product Name / Description Part Number Rack Conversion Kit Convert to 5U form factor N8143-71 9.2 Flash FDD Choose the Flash FDD if you need to prepare an alternative for a floppy drive. Product Name / Description Part Number Flash FDD USB flash emulating USB floppy disk, Native capacity 1.44 MB N8160-86 NEC Corporation Revision 4.3, February 2012 30 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E 9.3 Server Management License The server integrates the EXPRESSSCOPE Engine 2 as standard. Refer to Server Management for the standard management features. For more extensive remote KVM and remote media features, choose the following kit. Product Name / Description Part Number Remote KVM and Media License Kit N8115-03 License for one server. Remote KVM and remote media are enabled regardless of OS status. Remote KVM: Displays a graphics console on the web browser of the remote terminal (PC/server). Controls keyboard and mouse via the remote terminals' web browser Remote media: Enables the user to use the CD / DVD / FD / Flash memory of the remote terminals (PC/server) as if accessing the local drives. NOTE: Remote KVM and remote media features are not available for virtual machines. 9.4 Medium and Cartridge Category Product Name Drive supported Part Number RDX RDX Cartridge (320GB) N8151-86 N8152-26 RDX Cartridge (500GB) N8151-86 N8152-27 RDX Cartridge (1TB) N8151-86 N8152-33 DAT72(36GB) Medium 5 pack N8151-69 N8152-08 DAT 10 Support Service 10.1 Software Product Name / Description Part Number PP Support Pack (VMware ESXi 4.1 for 1 processor)(1year) Technical Support Service regarding ESXi (for quick solutions to technical issues) NOTE: It is necessary to purchase a PP support pack for each processor installed in the system. ULH1S-SV40-008F NEC Corporation Revision 4.3, February 2012 31 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E References Server Management The EXPRESSSCOPE Engine 2, integrated into the server, provides superior remote control and system management features listed in the table below. Standard Hardware monitoring 1 Temperature/voltage/power unit / fan /degeneration (memory/hard drive) Hardware event log collection With Remote KVM and Media License kit 2 Boot monitoring Booting, BIOS/POST stall, OS stall, shutdown Alerting HW error, Boot error and OS panic (by SNMP, E-Mail) Remote KVM POST/BIOS setup, DOS utility 3 3 Text-based screen (OS console) 3 (via LAN) Panic screen, Boot screen 2 GUI-based screen (OS console) - Remote control Remote reset/power on-off/ dump (via LAN) OS shutdown Remote media (CD/DVD/FD) - Server Management Command Line Protocol (DMTF compliant) Remote control via Web browser (without dedicated app) Remote batch 2 2 Scheduling (without UPS) 2 2 Others Set automatic IP address via DNS/DHCP Remote wakeup Wake On LAN, Wake On Ring Centralized management 1 2 3 Monitoring and control of multiple servers 2 2 2 2 The feature is not supported on non-hot plug power supply unit. The feature is not supported on VMware systems. The standard serial port is not available for the feature. NEC Corporation Revision 4.3, February 2012 32 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E OS Support Matrix for PCI Cards ESXi 4.1 RHEL 4 x64 RHEL 4 RHEL 5 x64 RHEL 5 RHEL 6 x64 RHEL 6 WS 2003 WS 2003R2 x64 WS 2003R2 WS 2008 x64 WS 2008 WS 2008R2 Part Number Product Name N8103-128 RAID Controller - N8103-129 RAID Controller N8103-130 RAID Controller N8103-134 RAID Controller - N8103-135 RAID Controller N8103-104A SAS Controller, 3 Gb/s - - - N8103-142 SAS Controller, 6 Gb/s - - - N8104-119 1000BASE-T Adapter - N8104-126 1000BASE-T Adapter N8104-121 1000BASE-T Adapter (2ch) N8104-125A 1000BASE-T Adapter (4ch) N8104-123A 10GBASE-SR Adapter - N8104-128 10GBASE Adapter (SFP+/2ch) - NEC Corporation - - - - - - Revision 4.3, February 2012 - - - - - - - - - - 33 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Supporting PCI Cards and Installable Slots Part Number Product Name Slots Remarks Slot # : #1 #2 #3 #4 #5 #6 PCI Slot: x8 x8 x8 x8 x4 32-bit Card height: FH FH FH FH FH FH Slot type: x8 x8 x8 x8 x8 5V Installable card length (mm) : 150 173 173 173 173 312 N8103-128 RAID Controller (128MB, RAID 0/1) [PCIe 2.0 x8] - - - - - N8103-129 RAID Controller (256MB, RAID 0/1) [PCIe 2.0 x8] - - - - - N8103-130 RAID Controller (256MB, RAID 0/1/5/6) [PCIe 2.0 x8] - - - - - N8103-134 RAID Controller (512MB,RAID 0/1/5/6) [PCIe 2.0 x8] - - - - - N8103-135 RAID Controller (512MB,RAID 0/1/5/6) [PCIe 2.0 x8] - - - N8103-104A SAS Controller [PCIe x8] - - - N8103-142 SAS Controller [PCIe 2.0 x8] - - - N8104-119 1000BASE-T Adapter [64-bit / 133 MHz PCI-X] - - - - - N8104-126 1000BASE-T adapter [PCIe x1] - Max. 3 N8104-121 1000BASE-T Adapter (2ch) [PCIe x4] - Max. 2 N8104-125A 1000BASE-T Adapter (4ch) [PCIe x4] - - - N8104-123A 10GBASE-SR Adapter [PCIe x8] - - - Max. 1 N8104-128 10GBASE adapter (SFP+/2ch) [PCIe 2.0 x8] - - - Max. 2 NEC Corporation Revision 4.3, February 2012 Max. 2 34 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Copyright Notice and Liability Disclaimer The information contained herein is subject to change without notice. Microsoft and Windows Server are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries Intel and Xeon are registered trademarks or trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Linux is a trademark of Linus Torvalds. Red Hat is a registered trademark of Red Hat, Inc. in the U.S. All other products, brands, or trade names used in this document are trademarks or registered trademarks of their respective holders. NEC shall not be liable for technical or editorial errors or omissions contained herein. For hard drive capacity measurements, 1 GB = 1 billion bytes. Actual formatted capacity is less. NEC Corporation Revision 4.3, February 2012 35 CONFIGURATION GUIDE – NEC EXPRESS5800/T120b-E Revision History Revision Date Description 4.3 February 13, 2012 Discontinued products removed: 160GB RDX Cartridge / N8152-20 640GB RDX Cartridge / N8152-30 Part number changed: 146.5GB 2.5-inch SAS HDD / N8150-374 300GB 2.5-inch SAS HDD / N8150-375 450GB 2.5-inch SAS HDD / N8150-376 600GB 2.5-inch SAS HDD / N8150-377 4.2 January 23, 2012 New products added: 4GB Memory Kit / N8102-431 Discontinued products removed: 4GB Memory Kit / N8102-381 Part number changed: 73.2GB 2.5-inch SAS HDD / N8150-378 146.5GB 2.5-inch SAS HDD / N8150-379 4.1 January 11, 2012 Discontinued products removed: SCSI Controller / N8103-107 100BASE-SX Adapter / N8104-112 Part number changed: 160GB SATA HDD / N8150-386 250GB SATA HDD / N8150-387 500GB SATA HDD / N8150-388 Others: Correct incorrect information in internal drive configuration using 3TB 3.5-inch SATA drive 4.0 December 14, 2011 New products added: 3TB 3.5-inch SATA HDD / N8150-337 2GB Memory Kit / N8102-430 Discontinued products removed: 1GB Memory Kit / N8102-379 2GB Memory Kit / N8102-380 2GB Memory Kit / N8102-392 3.2 October 18, 2011 Other: Add section for RAID 0/1 Controller with 128 MB Cache drive configuration Correct incorrect information in Specification, 2 2nd Processor, Maximum Available Memory, 4.2 Internal Drive Configuration, 8.4 Input Devices, and References. 3.1 August 24, 2011 Other: Add the remark in section for server management Add section for Medium and Cartridge 3.0 July 29, 2011 New products added: 300GB HDD / N8150-331 900GB HDD / N8150-332 Discontinued products removed: SCSI Controller / N8103-75 100BASE-TX Adapter / N8104-111 2.0 April 8, 2011 New products added: 1TB HDD / N8150-334 1.0 February 14, 2011 Initial release NEC Corporation Revision 4.3, February 2012 36