1600UT (Ultra Thermal) Curtain Wall System 1600UT System 1 / System 2 TM TM TM Ultra thermal. Ultra value. Ultra innovative. With increasing energy costs and stringent code requirements, building owners, architects and glaziers need high-performing products that can help them stay ahead of codes. Kawneer’s 1600UT (Ultra Thermal) Curtain Wall System™ is an ultra innovative solution that raises the standards for pre-engineered performance. Built on the success of the flagship 1600 curtain wall platform, the 1600UT System™1 and 1600UT System™2 deliver high thermal performance, versatility, reliability and value. Both are stick fabricated, pressure glazed and ideal for low- to mid-rise commercial applications where high thermal performing façades are needed. 1600UT System™1 is an outside glazed, captured curtain wall system, while 1600UT System™2 is a Structural Silicone Glazed (SSG) curtain wall system. No matter the system, the end result is an ultra innovative, performance-driven, highvalue curtain wall solution. Setting the Standard in Thermal Innovation For the utmost in energy efficiency, Kawneer’s 1600UT Curtain Wall System™ features an engineered polymer thermal separator and accommodates either double or triple insulating glass. Additionally, an optional fiberglass pressure plate can further enhance condensation resistance and thermal performance. 1600UT Curtain Wall System™ integrates seamlessly with other high thermal performing windows and doors from Kawneer to create a complete, advanced, thermally efficient solution for commercial buildings. The system is tested in accordance with North American performance standards, including seismic, thermal cycling and dynamic water. Performance Kawneer’s 1600UT Curtain Wall System™ is designed to proactively address code requirements, including the International Energy Conservation Code (IECC), ASHRAE/IESNA 90.1, 189.1 and state codes. Both 1600UT Curtain Wall Systems™ are capable of beating these code requirements with double- and triple-glazed configurations. Thermal simulations showing temperature variations from exterior/cold side to interior/warm side. U-FACTOR* Triple Glazed Typical Performance Ranges Double Glazed Typical Performance Ranges 1600 Wall System®1 1" Insulating Glass 0.50 1600UT System™1 1" Insulating Glass 1600UT System™1 1-3/4" Insulating Glass SYSTEM U-FACTOR 0.45 Double Glazed, 1600UT System™1 0.40 0.35 Aesthetics Triple Glazed, 1600UT System™1 0.30 Double Glazed, 1600UT System™2 0.25 0.20 Triple Glazed, 1600UT System™2 0.15 0.08 0.10 0.12 0.14 0.16 0.18 0.20 0.22 0.24 0.26 0.28 0.30 0.32 CENTER OF GLASS U-FACTOR Each infill option offers two levels of performance ranges. These depend on pressure plate choice (aluminum or fiberglass) and system type. The fiberglass pressure plate option not only enhances thermal performance, but also improves condensation resistance. CONDENSATION RESISTANCE CRF FRAME GLASS PRESSURE PLATE TYPE 1" DOUBLE GLAZED INFILL 1-3/4" TRIPLE GLAZED INFILL I FRAME GLASS Aluminum Fiberglass 79 76 71 76 67 68 Aluminum Fiberglass 82 81 74 76 77 78 The 1600UT Curtain Wall System™ has been rigorously tested against the following performance standards. PERFORMANCE TEST STANDARDS Kawneer solutions are widely respected for their ability to deliver optimum energy performance without compromising aesthetics. The innovative 1600UT Curtain Wall System™ is no exception. Kawneer designed the system to integrate many of the aesthetic and functional options found in the industry benchmark Kawneer 1600 Wall Systems®. Among the aesthetic benefits of the versatile 1600UT Curtain Wall System™ is a unique design for the glass setting block chair, which allows for larger glass lites than other tripleglazed, high-performing curtain wall systems. Along with expansive glass sizes, the 1600UT System™2 offers a two-sided vertical SSG mullion solution that permits greater uninterrupted 1600UT SystemTM2 1600UT SystemTM1 (SSG) (Triple Glazing) sightlines while providing enhanced thermal performance. To create flush and unbroken sightlines, both systems use concealed fasteners in their joinery construction. Fabrication and Installation Air Infiltration Water – static Water – dynamic Structural – uniform wind load Thermal Cycling Thermal Transmittance – U-Factor Condensation Resistance (CRF, I, CR) Overall Solar Heat Gain Coefficient (SHGC, VT) Sound Transmission (STC, OITC) Seismic ASTM E 283 ASTM E 331 AAMA 501.1, 520 ASTM 330 AAMA 501.5 AAMA 1503, 507; NFRC 100 AAMA 1503; CSA A440.2; NFRC 500 AAMA 507, NFRC 200 ASTM E90, E1425 AAMA 501.4 The 1600UT Curtain Wall System™ minimizes installation time and effort in a number of ways: • Installers can leverage their existing knowledge of Kawneer’s time-tested 1600 Wall System®1 and System®2 fabrication and installation methods. • Straight cuts without notching simplify fabrication. • A pre-engineered rain screen back pan option is available that uses easy-to-install spandrel adapters. For the Finishing Touch *U-factor values are simulated using NFRC sizes and procedures. This chart is for general illustration purposes only. Please refer to thermal charts in the Kawneer Architectural Detail Manual on kawneer.com. Kawneer Company, Inc. Technology Park / Atlanta 555 Guthridge Court Norcross, GA 30092 © Kawneer Company, Inc. 2011 kawneer.com kawneergreen.com 770 . 449 . 5555 LITHO IN U.S.A. Form No. 11-2122 Architectural Class I anodized aluminum finishes are available in clear and color choices. Painted finishes, including fluoropolymer, that meet AAMA 2605 standards and solvent-free powder coatings that meet AAMA 2604 standards are available in a variety of color choices. MAY, 2016 1600UT SystemTM1 Curtain Wall FEATURES Features • 1600UT SystemTM1 is a high thermal performance, outside glazed, captured curtain wall system • Innovative design delivers high thermal performance while leveraging 1600 Wall System architecture • Multiple thermal performance levels resulting from a combination of: - 1" (25.4), 1-1/4" (31.8), 1-5/16" (33.34) double or 1-3/4" (44.5), triple glazed insulating glass units - Aluminum or fiberglass pressure plates • Thermal barrier design ensures high thermal performance without being susceptible to thermal fatigue • Offers integrated entrance framing systems • Corners and splays available • Comprehensively tested to latest high performance air, water, structural and thermal standards • Glass chairs support insulating glass units enabling larger expanses of glass • Pressure equalized system tested with vapor barrier • Two color option • PermanodicTM anodized finishes in seven choices • Painted finishes in standard and custom choices Optional Features • Steel reinforcing • Rain screen and backpans • Deep profile covers and bull nose covers • Deep and heavy-weight mullions • Integrates with standard Kawneer windows and GLASSventTM Windows for curtain wall • Profit$MakerTM plus die sets available © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-095 1 Product Applications • Ideal for low to mid-rise applications where high thermal performance is desired • High span applications For specific product applications, Consult your Kawneer representative. kawneer.com ADMD080EN Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall BLANK PAGE ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 EC 97911-095 MAY, 2016 MAY, 2016 1600UT SystemTM1 Curtain Wall EC 97911-095 3 INDEX Architects - Most extrusion and window types illustrated in this catalog are standard products for Kawneer. These concepts have been expanded and modified to afford you design freedom. Some miscellaneous details are non-standard and are intended to demonstrate how the system can be modified to expand design flexibility. Please contact your Kawneer representative for further assistance. LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. PICTORIAL VIEW.................................................................................4 1" INFILL DETAILS...............................................................................5 ENTRANCE DETAILS................................................................. 6-8 CORNERS.......................................................................................9 SPLAYED MULLION OPTIONS....................................................10 WINDOWS.....................................................................................11 1-3/4" INFILL DETAILS......................................................................12 ENTRANCE DETAILS............................................................. 13-15 CORNERS.....................................................................................16 WINDOWS.....................................................................................17 BACKPAN DETAILS.....................................................................18, 19 MISCELLANEOUS FRAMING......................................................20, 21 ANCHORING................................................................................22, 23 WIND LOAD CHARTS.................................................................. 24-32 DEADLOAD CHARTS.................................................................. 33-38 THERMAL CHARTS .................................................................... 39-53 The following metric (SI ) units are found in these details: m –meter cm – centimeter mm –millimeter s –second Pa –pascal MPa –megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement. kawneer.com ADMD080EN Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall PICTORIAL VIEW ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 4 EC 97911-095 MAY, 2016 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 6 6B 5 2-1/2" (63.5) kawneer.com 2-1/2" (63.5) 6A 7 7-1/2" (190.5) 6" (152.4) © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. MAY, 2016 1600UT SystemTM1 Curtain Wall EC 97911-095 1" INFILL DETAILS SCALE 3" = 1'-0" 1 1A 1 2 2A 3 7A 1A 4 7 7B OPTIONAL FIBERGLASS PRESSURE PLATE 6 6A 6B 1/4" INFILL ADAPTER OPEN BACK JAMB 7A 1/4" INFILL ADAPTER 7B STEEL REINFORCING AS REQUIRED ADMD080EN TUBE HORIZONTAL 2 ELEVATION IS NUMBER KEYED TO DETAILS 6" (152.4) 7-1/2" (190.5) OPEN BACK HORIZONTAL 2A 3 4 5 5 1600UT SystemTM1 Curtain Wall 6 MAY, 2016 EC 97911-095 NON-THERMAL ENTRANCE DETAILS (1" INFILL) SCALE 3" = 1'-0" 3 4 6 1 1-3/4" (50.8) 2 1/8" (3.2) 2-1/2" (63.5) 5 TRANSOM BAR B/H OR O/P C/H BUTT HUNG OR OFFSET PIVOT WITH SURFACE CLOSER OR FLOOR CLOSER B/H OR O/P 1/8" (3.2) 2-1/2" (63.5) ELEVATION IS NUMBER KEYED TO DETAILS 2 1-3/4" (50.8) DOOR JAMB BUTT HUNG OR OFFSET PIVOT 1A Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1 1A TRANSOM BAR 1/8" (3.2) CENTER HUNG 1-3/4" (50.8) 4 3 TRANSOM BAR CENTER HUNG WITH CONCEALED OVERHEAD OR FLOOR CLOSER 6 DOOR JAMB 2-1/2" (63.5) 3/4" (19.1) TYP. 5 BUTT HUNG OR OFFSET PIVOT TRANSOM BAR BUTT HUNG OR OFFSET PIVOT WITH LCN CONCEALED OVER HEAD CLOSER OR SURFACE CLOSER ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 DOOR JAMB 2-1/2" (63.5) 3/4" (19.1) TYP. Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. BUTT HUNG OR OFFSET PIVOT WITH SINGLE ACTING OFFSET ARM CLOSER © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 kawneer.com 1" (25.4) 2-1/2" (63.5) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 1600UT SystemTM1 Curtain Wall EC 97911-095 AATM250/425 THERMAL ENTRANCE DETAILS (1" INFILL) SCALE 3" = 1'-0" 1 1A 2 2A ELEVATION IS NUMBER KEYED TO DETAILS B/H OR O/P 2-1/2" (63.5) 1" (25.4) DOOR JAMB BUTT HUNG OR OFFSET PIVOT DOOR JAMB BUTT HUNG OR OFFSET PIVOT ADMD080EN 1 TRANSOM BAR BUTT HUNG OR OFFSET PIVOT WITH SURFACE CLOSER OR FLOOR CLOSER 1A 2A TRANSOM BAR BUTT HUNG OR OFFSET PIVOT WITH SURFACE CLOSER OR FLOOR CLOSER 7 SCALE 3" = 1'-0" ELEVATION IS NUMBER KEYED TO DETAILS B/H OR O/P 2-1/2" (63.5) 1" (25.4) DOOR JAMB BUTT HUNG OR OFFSET PIVOT BUTT HUNG OR OFFSET PIVOT DOOR JAMB ADMD080EN 1 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. INSULCLADTM THERMAL ENTRANCE DETAILS (1" INFILL) BUTT HUNG OR OFFSET PIVOT WITH SURFACE CLOSER OR FLOOR CLOSER 1A 2A TRANSOM BAR BUTT HUNG OR OFFSET PIVOT WITH SURFACE CLOSER OR FLOOR CLOSER kawneer.com © Kawneer Company, Inc., 2013 2-1/2" (63.5) 1600UT SystemTM1 Curtain Wall Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 1" (25.4) 8 EC 97911-095 MAY, 2016 1 1A 2 2A TRANSOM BAR © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 kawneer.com 1600UT SystemTM1 Curtain Wall EC 97911-095 CORNERS (1" INFILL) SCALE 3" = 1'-0" 90° OUTSIDE CORNER 90° INSIDE CORNER 90° OUTSIDE CORNER 135° OUTSIDE CORNER 0° TO 5° 0° TO 5° OUTSIDE SPLAYED MULLIONS INSIDE SPLAYED MULLIONS OTHER SPLAY OPTIONS AVAILABLE ADMD080EN 9 0° TO 5° 0° TO 5° 5° TO 15° 5° TO 15° ADMD080EN 15° TO 25° OUTSIDE SPLAYED MULLIONS 15° TO 25° INSIDE SPLAYED MULLIONS kawneer.com © Kawneer Company, Inc., 2013 SPLAYED MULLION OPTIONS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 10 EC 97911-095 MAY, 2016 SCALE 3" = 1'-0" © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 SCALE 3" = 1'-0" kawneer.com 1600UT SystemTM1 Curtain Wall EC 97911-095 WINDOWS GLASSventTM UT Windows HEAD SILL JAMB AA™900 Thermal Windows HEAD SILL JAMB NOTE: AA™6400 vent can be accommodated. Contact your Kawneer representative for other options. ADMD080EN 11 1 2 2A 3 2-1/2" (63.5) 7A 1A 4 7 7B 5 OPTIONAL FIBERGLASS PRESSURE PLATE ELEVATION IS NUMBER KEYED TO DETAILS 6 7 6A 6B 1" INFILL ADAPTER OPEN BACK JAMB 7A 7B 1" INFILL ADAPTER ADMD080EN TUBE HORIZONTAL 2 2A 3 4 5 STEEL REINFORCING AS REQUIRED kawneer.com © Kawneer Company, Inc., 2013 1-3/4" INFILL DETAILS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 6 6B 2-1/2" (63.5) 6A 8-1/4" (209.5) 6-3/4" (171.4) 12 EC 97911-095 MAY, 2016 SCALE 3" = 1'-0" 1 1A 6-3/4" (171.4) 8-1/4" (209.5) OPEN BACK HORIZONTAL 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 13 NON-THERMAL ENTRANCE DETAILS (1-3/4" INFILL) SCALE 3" = 1'-0" 1 1A 3 6 1 1-3/4" (50.8) 4 TRANSOM BAR B/H OR O/P C/H BUTT HUNG OR OFFSET PIVOT WITH SURFACE CLOSER OR FLOOR CLOSER B/H OR O/P DOOR JAMB 2 1A 1/8" (3.2) 2-1/2" (63.5) ELEVATION IS NUMBER KEYED TO DETAILS BUTT HUNG OR OFFSET PIVOT 1-3/4" (50.8) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2 1/8" (3.2) 2-1/2" (63.5) 5 TRANSOM BAR BUTT HUNG OR OFFSET PIVOT WITH SINGLE ACTING OFFSET ARM CLOSER 2-1/2" (63.5) 1/8" (3.2) DOOR JAMB CENTER HUNG 3 1-3/4" (50.8) 4 TRANSOM BAR CENTER HUNG WITH CONCEALED OVERHEAD OR FLOOR CLOSER 3/4" (19.1) TYP. 2-1/2" (63.5) © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 3/4" (19.1) TYP. 6 5 DOOR JAMB BUTT HUNG OR OFFSET PIVOT TRANSOM BAR BUTT HUNG OR OFFSET PIVOT WITH LCN CONCEALED OVER HEAD CLOSER OR SURFACE CLOSER kawneer.com ADMD080EN SCALE 3" = 1'-0" ELEVATION IS NUMBER KEYED TO DETAILS B/H OR O/P 2-1/2" (63.5) BUTT HUNG OR OFFSET PIVOT DOOR JAMB ADMD080EN 1 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AATM250/425 THERMAL ENTRANCE DETAILS (1-3/4" INFILL) TRANSOM BAR BUTT HUNG OR OFFSET PIVOT WITH SURFACE CLOSER OR FLOOR CLOSER kawneer.com © Kawneer Company, Inc., 2013 2 2-1/2" (63.5) 1600UT SystemTM1 Curtain Wall Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1" (25.4) 14 EC 97911-095 MAY, 2016 1 2 1" (25.4) © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1" (25.4) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2 kawneer.com 2-1/2" (63.5) MAY, 2016 1600UT SystemTM1 Curtain Wall EC 97911-095 INSULCLADTM THERMAL ENTRANCE DETAILS (1-3/4"" INFILL) SCALE 3" = 1'-0" 2-1/2" (63.5) 1 2 ELEVATION IS NUMBER KEYED TO DETAILS B/H OR O/P BUTT HUNG OR OFFSET PIVOT DOOR JAMB ADMD080EN 1 1" (25.4) TRANSOM BAR BUTT HUNG OR OFFSET PIVOT WITH SURFACE CLOSER OR FLOOR CLOSER 15 90° OUTSIDE CORNER 90° INSIDE CORNER 90° OUTSIDE CORNER 135° OUTSIDE CORNER 0° TO 5° 0° TO 5° OUTSIDE SPLAYED MULLIONS INSIDE SPLAYED MULLIONS OTHER SPLAY OPTIONS AVAILABLE ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 CORNERS (1-3/4" INFILL) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 16 EC 97911-095 MAY, 2016 SCALE 3" = 1'-0" © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 SCALE 3" = 1'-0" kawneer.com 1600UT SystemTM1 Curtain Wall EC 97911-095 WINDOWS GLASSventTM UT Windows HEAD SILL JAMB AA™900 Thermal Windows HEAD SILL JAMB NOTE: AA™6400 vent can be accommodated. Contact your Kawneer representative for other options. ADMD080EN 17 1 2 JAMB MULLION AT SPANDREL (With vapor barrier tie-in) MULLION AT SPANDREL 3/8" (9.5) 2-1/2" (63.5) D.L.O. 4 3 HEAD TRANSOM AT PARAPET FLASHING 4 ELEVATION IS NUMBER KEYED TO DETAILS ADMD080EN Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 3/8" (9.5) BACKPAN DETAILS (1" INFILL) 5 TYPICAL DEADLOAD ANCHOR 6 TRANSOM – SPANDREL OVER VISION kawneer.com © Kawneer Company, Inc., 2013 NOTE: 6" SYSTEM SHOWN, 7-1/2" SYSTEM SIMILAR MULLION LENGTH 1600UT SystemTM1 Curtain Wall Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 6 1/2" (12.7) 5 D.L.O. 2 MULLION LENGTH 1 CONSTRUCTION JOINT 1/2" (12.7) MAX (ALLOWS +/-1/4" MOVEMENT) 18 EC 97911-095 MAY, 2016 SCALE 3" = 1'-0" 3 EXPANSION JOINT © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 1 kawneer.com 1600UT SystemTM1 Curtain Wall EC 97911-095 BACKPAN DETAILS (1-3/4" INFILL) SCALE 3" = 1'-0" 3 3 4 HEAD TRANSOM AT PARAPET FLASHING 2 5 6 1 JAMB MULLION AT SPANDREL (With vapor barrier tie-in) 4 ELEVATION IS NUMBER KEYED TO DETAILS NOTE: 6" SYSTEM SHOWN, 7-1/2" SYSTEM SIMILAR EXPANSION JOINT 2 5 MULLION AT SPANDREL TYPICAL DEADLOAD ANCHOR 6 TRANSOM – SPANDREL OVER VISION ADMD080EN 19 1600UT SystemTM1 Curtain Wall 20 MAY, 2016 MISCELLANEOUS FRAMING EC 97911-095 SCALE 3" = 1'-0" Architects – Most extrusion and window types illustrated in this catalog are standard products for Kawneer. These concepts have been expanded and modified to afford you design freedom. Some miscellaneous details are non-standard and are intended to demonstrate how the system can be modified to expand design flexibility. Please contact your Kawneer representative for further assistance. 3" (76.2) 2-1/2" (63.5) 1-1/4" (31.8) 4-3/4" (120.7) 2-3/4" (69.7) 2-1/2" (63.5) 2-1/2" (63.5) OPTIONAL BULL NOSE COVERS 2-1/2" (63.5) 2-1/2" (63.5) 3-1/4" (82.6) VARIES 2-1/2" (63.5) DOUBLE MULLION VENEER SYSTEM 069263 GYPSUM BOARD TRIM THERMAL PERIMETER PRESSURE PLATE STOOL TRIM OPTIONS: 069264 - 2-3/4" (69.9) 069265 - 4-1/2" (114.3) 069266 - 5" (127.0) 069267 - 6-1/8" (155.6) 069268 - 6-3/4" (171.4) NOTE: STOOL TRIMS REQUIRE 069271 TRIM CLIP PACKAGE INTERIOR STOOL TRIM ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 OPTIONAL DEEP COVERS NOTE: 1-3/4" triple glazing similar. 2-1/2" (63.5) DEEP MULLION Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2" (50.8) 1-3/16" (30.1) 10-1/2" (266.7) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 162-064 © Kawneer Company, Inc., 2013 kawneer.com 2-1/2" (63.5) 7-3/4" (305.6) 6-1/4" (158.8) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2-1/2" (63.5) 7-3/4" (305.6) 6-1/4" (158.8) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 1600UT SystemTM1 Curtain Wall EC 97911-095 MISCELLANEOUS FRAMING 1-1/4" INFILL DETAILS 7-3/4" (305.6) 6-1/4" (158.8) 2-1/2" (63.5) 1-5/16" INFILL DETAILS 6-1/4" (158.8) 7-3/4" (305.6) 2-1/2" (63.5) ADMD080EN 21 1" (25.4) ANCHORING TO FLOOR SLAB 1" (25.4) ANCHORING TO SUPPORT STEEL NOTE: 1-3/4" triple glazing similar. ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 ANCHORING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 22 EC 97911-095 MAY, 2016 Actual project conditions will determine specific anchor design. Details on this page are for reference only. © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 kawneer.com 1600UT SystemTM1 Curtain Wall EC 97911-095 ANCHORING Actual project conditions will determine specific anchor design. Details on this page are for reference only. 1" (25.4) ANCHORING TO HORIZONTAL STRUCTURAL STEEL NOTE: 1-3/4" triple glazing similar. 1" (25.4) ANCHORING TO VERTICAL STRUCTURAL STEEL ADMD080EN 23 24 1600UT SystemTM1 Curtain Wall WIND LOAD / DEADLOAD CHARTS MAY, 2016 EC 97911-095 DEADLOAD CHARTS Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Horizontal or deadload limitations are based upon 1/8" (3.2), maximum allowable deflection at the center of an intermediate horizontal member. The accompanying charts are calculated for 1" (25.4) thick insulating glass or 1-3/4" (44.5) thick glass supported on two setting blocks placed at the loading points shown. ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 Mullions are designed for deflection limitations in accordance with AAMA TIR-A11 of L/175 up to 13'-6" and L/240 +1/4" above 13'-6". These curves are for mullions WITH HORIZONTALS and are based on engineering calculations for stress and deflection. Allowable wind load stress for ALUMINUM 15,152 psi (104MPa), STEEL 30,000 psi (207MPa). Charted curves, in all cases are for the limiting value. Wind load charts contained herein are based upon nominal wind load utilized in allowable stress design. A conversion from Load Resistance Factor Design (LRFD) is provided. To convert ultimate wind loads to nominal loads, multiply ultimate wind loads by a factor of 0.6 per ASCE/SEI 7. A 4/3 increase in allowable stress has not been used to develop these curves. For special situations not covered by these curves, contact your Kawneer representative for additional information. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. WIND LOAD CHARTS 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 WIND LOAD CHARTS (1" INFILL) SINGLE SPAN METERS 1 1.5 A= B= C= D= E= 2 7 23 6.5 21 20 TWIN SPAN LRFD Ultimate Design Load 33 PSF (1580) 50 PSF (2400) 67 PSF (3200) 83 PSF (4000) 100 PSF (4800) METERS .5 28 8.5 27 A 26 5.5 A 10 E 7 2.5 171213 2 3 4 5 B 21 6 7 6.5 20 6 19 C 18 5.5 D 5 E 4.5 14 2 1 22 15 6 0 7 23 16 C D 8 7.5 24 17 3 B 9 MULLION HEIGHT IN FEET 3.5 11 MULLION HEIGHT EQUAL EQUAL 12 6" (152.4) 4 13 MULLION HEIGHT 4.5 14 METERS 5 15 8 25 17 16 2 9 6 18 MULLION HEIGHT IN FEET 1.5 29 19 5 1 30 8 4 13 I = 3.662(152.42 x 104) S = 1.662(27.24 x 103) 12 0 1 2 3 4 5 6 7 MULLION CENTERS IN FEET MULLION CENTERS IN FEET SINGLE SPAN TWIN SPAN METERS .5 1 8 METERS 1.5 .5 2 7 23 1 1.5 2 30 9 22 29 6.5 20 28 6 5.5 12 A 11 3.5 B 10 3 C 9 D 2.5 3 4 5 6 7 MULLION CENTERS IN FEET kawneer.com 6.5 21 20 6 D 19 E 18 5.5 5 8 4.5 14 171214 6 2 C 22 15 2 1 7 23 17 E 0 7.5 24 16 8 7 MULLION HEIGHT IN FEET 4 13 MULLION HEIGHT EQUAL EQUAL 4.5 14 6" (152.4) 15 METERS 5 16 8 B 25 17 MULLION HEIGHT 18 MULLION HEIGHT IN FEET A 26 19 5 8.5 27 I = 4.5071(87.60 x 104) S = 1.968(32.25 x 103) ADMD080EN 4 13 12 0 1 2 3 4 5 6 7 MULLION CENTERS IN FEET 8 METERS 21 © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 22 Allowable Stress Design Load 20 PSF (960) 30 PSF (1440) 40 PSF (1920) 50 PSF (2400) 60 PSF (2880) METERS .5 25 1600UT SystemTM1 Curtain Wall MAY, 2016 WIND LOAD CHARTS (1" INFILL) 1 1.5 A= B= C= D= E= 2 7 23 22 6.5 21 20 METERS .5 2 9 A 28 8.5 27 6 8 26 5.5 13 4 B 12 C 11 3.5 D 10 MULLION HEIGHT IN FEET 4.5 A 14 7-1/2" (190.5) 15 METERS 5 16 MULLION HEIGHT EQUAL EQUAL 25 17 MULLION HEIGHT 18 MULLION HEIGHT IN FEET 1.5 29 19 8 7 171215 3 22 C 21 6.5 20 6 19 D 18 5.5 E 5 4 5 6 7 4.5 14 2 2 7 23 15 6 1 7.5 16 2.5 0 B 24 17 3 E 9 5 1 30 8 4 13 I = 7.915(329.45 x 104) S = 2.635(43.18 x 103) 12 0 1 2 3 4 5 6 7 8 MULLION CENTERS IN FEET MULLION CENTERS IN FEET SINGLE SPAN TWIN SPAN METERS .5 1 METERS 1.5 .5 2 7 23 1 1.5 2 30 9 29 6.5 21 20 8.5 B 27 6 8 26 19 5.5 4 C 12 3.5 11 D 10 7.5 24 23 7 D 22 6.5 21 E 20 6 19 5.5 18 17 3 E MULLION HEIGHT IN FEET B 13 MULLION HEIGHT EQUAL EQUAL 4.5 A 14 7-1/2" (190.5) 15 METERS 5 16 C 25 17 MULLION HEIGHT 18 MULLION HEIGHT IN FEET A 28 9 5 16 2.5 8 7 15 6 171216 13 5 I = 9.594(399.33 x 104) S = 3.163(51.83 x 103) 12 1 2 3 4 5 6 7 MULLION CENTERS IN FEET 8 4.5 14 2 0 METERS 22 ADMD080EN 4 0 1 2 3 4 5 6 7 8 MULLION CENTERS IN FEET kawneer.com © Kawneer Company, Inc., 2013 .5 TWIN SPAN LRFD Ultimate Design Load 33 PSF (1580) 50 PSF (2400) 67 PSF (3200) 83 PSF (4000) 100 PSF (4800) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. METERS Allowable Stress Design Load 20 PSF (960) 30 PSF (1440) 40 PSF (1920) 50 PSF (2400) 60 PSF (2880) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. SINGLE SPAN EC 97911-095 METERS 26 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 WIND LOAD CHARTS (1" INFILL) SINGLE SPAN 162016 W/162300 A= B= C= D= E= METERS .5 1 1.5 2 30 29 28 SINGLE SPAN LRFD Ultimate Design Load 33 PSF (1580) 50 PSF (2400) 67 PSF (3200) 83 PSF (4000) 100 PSF (4800) 162016 W/162301 METERS .5 1 1.5 2 30 9 29 28 8.5 8.5 27 25 25 MULLION HEIGHT A 21 6.5 20 METERS 7 22 6 19 B 18 17 5.5 5 14 E 0 1 2 3 7 23 22 6.5 21 A 20 B 6 19 18 5.5 C 4 4 5 6 7 5 16 4.5 D 13 7.5 24 17 C 16 15 MULLION HEIGHT IN FEET 7.5 24 23 8 26 8 171216 W/162300 171216 W/162301 Ia = 9.594(399.33 x 104) Sa = 3.163(51.83 x 103) Is = 3.805(158.37 x 104) Ss = 1.669(27.35 x 103) Ia = 9.594(399.33 x 104) Sa = 3.163(51.83 x 103) Is = 5.684(236.59 x 104) Ss = 2.493(40.85 x 103) D 15 4.5 E 14 4 13 12 0 1 2 3 4 5 6 7 MULLION CENTERS IN FEET MULLION CENTERS IN FEET SINGLE SPAN SINGLE SPAN 162016 W/162301/302 162016 W/162301/302/303 .5 1 8 METERS 1.5 .5 2 30 1 1.5 2 30 9 9 29 29 28 28 8.5 8 26 25 6.5 21 20 B 6 19 18 MULLION HEIGHT IN FEET MULLION HEIGHT 7 A 22 5.5 C A 25 7.5 24 23 8 26 METERS MULLION HEIGHT IN FEET 8.5 27 17 7.5 24 7 23 B 22 6.5 21 C 20 6 19 D 17 16 15 D 5 E 4.5 14 4 13 0 1 2 3 4 5 6 7 8 E 5 16 171216 W/162301/302 171216 W/162301/302/303 Ia = 9.594(399.33 x 104) Sa = 3.163(51.83 x 103) Is = 7.893(328.53 x 104) Ss = 3.462(56.73 x 103) Ia = 9.594(399.33 x 104) Sa = 3.163(51.83 x 103) Is = 9.347(389.05 x 104) Ss = 4.100(67.19 x 103) MULLION CENTERS IN FEET kawneer.com 5.5 18 15 4.5 14 4 13 12 0 1 2 3 4 5 6 7 MULLION CENTERS IN FEET ADMD080EN 8 METERS 27 12 METERS 8 26 METERS © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Allowable Stress Design Load 20 PSF (960) 30 PSF (1440) 40 PSF (1920) 50 PSF (2400) 60 PSF (2880) 27 MULLION HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 9 12 27 WIND LOAD CHARTS (1" INFILL) 12 0 1 1 2 3 1.5 26 25 23 7 22 21 A 20 19 18 17 16 4 5 6.5 B 6 D C 5.5 E 15 13 6 7 MULLION CENTERS IN FEET 8 Allowable Stress Design Load 20 PSF (960) 30 PSF (1440) 40 PSF (1920) 50 PSF (2400) 60 PSF (2880) LRFD Ultimate Design Load 33 PSF (1580) 50 PSF (2400) 67 PSF (3200) 83 PSF (4000) 100 PSF (4800) 2 27 8.5 8 24 7.5 5 14 4.5 4 ADMD080EN Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall kawneer.com © Kawneer Company, Inc., 2013 METERS 10-1/2" (269.9) 28 MULLION HEIGHT .5 METERS SINGLE SPAN A= B= C= D= E= Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. MULLION HEIGHT IN FEET 28 EC 97911-095 MAY, 2016 I = 36.451(1517.20 x 104) S = 8.279(135.67 x 103) 171266 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 WIND LOAD CHARTS (1-3/4" INFILL) SINGLE SPAN METERS 1 1.5 A= B= C= D= E= 2 7 23 6.5 21 20 TWIN SPAN LRFD Ultimate Design Load 33 PSF (1580) 50 PSF (2400) 67 PSF (3200) 83 PSF (4000) 100 PSF (4800) METERS .5 1.5 2 9 29 28 8.5 27 6 A 26 5.5 4 13 A 12 B 11 3.5 C 10 B 23 7 C 22 6.5 21 20 D 6 19 E 18 5.5 5 16 E 8 7.5 24 17 3 D 9 MULLION HEIGHT IN FEET 4.5 14 MULLION HEIGHT EQUAL EQUAL 15 METERS 5 6-3/4" (171.5) 17 16 8 25 MULLION HEIGHT 18 2.5 7 15 171201 2 4.5 14 4 13 6 0 1 2 3 4 5 6 7 I = 5.035(209.57 x 104) S = 1.993(32.66 x 103) 8 MULLION CENTERS IN FEET 12 0 1 2 1 4 5 6 7 8 TWIN SPAN METERS METERS .5 3 MULLION CENTERS IN FEET SINGLE SPAN 1.5 2 .5 7 23 1 1.5 2 30 9 22 29 6.5 20 6 8 26 5.5 4 13 B 12 3.5 11 C 10 7.5 24 C 23 7 22 6.5 21 D 20 6 19 E 18 5.5 17 3 D 9 MULLION HEIGHT IN FEET A MULLION HEIGHT EQUAL EQUAL 4.5 14 6-3/4" (171.5) 15 METERS 5 16 B 25 17 MULLION HEIGHT 18 MULLION HEIGHT IN FEET 8.5 27 19 5 16 E 8 2.5 7 2 15 171202 6 5 A 28 4.5 14 4 13 0 1 2 3 4 5 6 7 MULLION CENTERS IN FEET kawneer.com 8 I = 6.779(282.16 x 104) S = 2.652(43.46 x 103) ADMD080EN 12 0 1 2 3 4 5 6 7 MULLION CENTERS IN FEET 8 METERS 21 © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1 30 19 MULLION HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 22 Allowable Stress Design Load 20 PSF (960) 30 PSF (1440) 40 PSF (1920) 50 PSF (2400) 60 PSF (2880) METERS .5 5 29 1600UT SystemTM1 Curtain Wall MAY, 2016 WIND LOAD CHARTS (1-3/4" INFILL) METERS 1.5 A= B= C= D= E= 2 7 23 22 6.5 21 20 METERS .5 2 9 A 28 8.5 27 6 B 26 5.5 B 13 4 C 12 3.5 D 11 E 10 MULLION HEIGHT IN FEET 4.5 A 14 8-1/4" (209.6) 15 METERS 5 16 MULLION HEIGHT EQUAL EQUAL 25 17 MULLION HEIGHT 18 MULLION HEIGHT IN FEET 1.5 29 19 8 7.5 C 24 7 23 D 22 6.5 21 E 20 6 19 5.5 18 17 3 5 16 9 2.5 8 15 171203 7 4.5 14 2 4 13 6 5 1 30 0 1 2 3 4 5 6 7 MULLION CENTERS IN FEET I = 10.135(421.85 x 104) S = 3.027(49.60 x 103) 8 12 0 1 2 SINGLE SPAN 1 4 5 6 7 8 TWIN SPAN METERS .5 3 MULLION CENTERS IN FEET METERS 1.5 .5 2 7 23 1 1.5 2 30 9 29 6.5 21 20 28 6 8 26 5.5 B 13 4 C 12 D 3.5 11 E 10 MULLION HEIGHT IN FEET 4.5 MULLION HEIGHT EQUAL EQUAL A 14 8-1/4" (209.6) 15 METERS 5 16 D 25 17 MULLION HEIGHT 18 MULLION HEIGHT IN FEET 8.5 C 27 19 7.5 E 24 7 23 22 6.5 21 20 6 19 5.5 18 17 3 9 5 16 2.5 8 15 171204 7 2 4.5 14 4 13 6 5 B 0 1 2 3 4 5 6 7 8 METERS 22 I = 12.736(530.11 x 104) S = 3.791(62.12 x 103) MULLION CENTERS IN FEET 12 0 1 2 3 4 5 6 7 8 MULLION CENTERS IN FEET ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 1 TWIN SPAN LRFD Ultimate Design Load 33 PSF (1580) 50 PSF (2400) 67 PSF (3200) 83 PSF (4000) 100 PSF (4800) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. .5 Allowable Stress Design Load 20 PSF (960) 30 PSF (1440) 40 PSF (1920) 50 PSF (2400) 60 PSF (2880) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. SINGLE SPAN EC 97911-095 METERS 30 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 WIND LOAD CHARTS (1-3/4" INFILL) SINGLE SPAN 162004 W/162300 A= B= C= D= E= METERS .5 1 1.5 2 30 28 Allowable Stress Design Load 20 PSF (960) 30 PSF (1440) 40 PSF (1920) 50 PSF (2400) 60 PSF (2880) SINGLE SPAN LRFD Ultimate Design Load 33 PSF (1580) 50 PSF (2400) 67 PSF (3200) 83 PSF (4000) 100 PSF (4800) 162004 W/162301 METERS .5 1.5 2 9 29 28 8.5 8.5 27 25 25 MULLION HEIGHT 6.5 21 A 20 6 B 19 18 METERS 7 22 MULLION HEIGHT IN FEET 7.5 24 23 5.5 C 8 26 17 7.5 24 7 23 22 A 21 6.5 B 20 6 19 C 5.5 18 17 5 16 4.5 E 14 4 13 0 1 2 3 4 5 6 7 D 16 D 15 8 171204 W/162300 171204 W/162301 Ia = 12.736(530.11 x 104) Sa = 3.791(62.12 x 103) Is = 3.805(158.37 x 104) Ss = 1.669(27.35 x 103) Ia = 12.736(530.11 x 104) Sa = 3.791(62.12 x 103) Is = 5.684(236.59 x 104) Ss = 2.493(40.85 x 103) 5 E 15 4.5 14 4 13 12 0 1 2 3 4 5 6 7 SINGLE SPAN SINGLE SPAN 162004 W/162301/302/303 METERS 1 8 MULLION CENTERS IN FEET 162004 W/162301/302 .5 METERS 1.5 .5 2 30 1 1.5 2 30 9 9 29 29 28 28 8.5 8 26 25 7 A 22 6.5 21 B 20 MULLION HEIGHT 24 6 19 C 18 MULLION HEIGHT IN FEET 7.5 23 8 26 METERS MULLION HEIGHT IN FEET 25 © Kawneer Company, Inc., 2013 8.5 27 5.5 17 7.5 24 A 7 23 22 B 21 20 D 5 E 15 4.5 5.5 18 D 14 4 13 0 1 2 3 4 5 6 7 8 171204 W/162301/302/303 Ia = 12.736(530.11 x 104) Sa = 3.791(62.12 x 103) Is = 7.893(328.53 x 104) Ss = 3.462(56.73 x 103) Ia = 12.736(530.11 x 104) Sa = 3.791(62.12 x 103) Is = 9.347(389.05 x 104) Ss = 4.100(67.19 x 103) MULLION CENTERS IN FEET kawneer.com 5 16 171204 W/162301/302 6 C 19 17 16 6.5 E 15 4.5 14 4 13 12 0 1 2 3 4 5 6 7 MULLION CENTERS IN FEET ADMD080EN 8 METERS 27 12 METERS 8 26 MULLION CENTERS IN FEET Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1 30 27 MULLION HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 9 29 12 31 12 WIND LOAD CHARTS (1-3/4" INFILL) 0 1 1 2 3 1.5 26 25 23 22 A 7 21 6.5 20 19 B 18 17 D 16 E 4 5 6 6 C 5.5 15 13 7 MULLION CENTERS IN FEET 8 Allowable Stress Design Load 20 PSF (960) 30 PSF (1440) 40 PSF (1920) 50 PSF (2400) 60 PSF (2880) LRFD Ultimate Design Load 33 PSF (1580) 50 PSF (2400) 67 PSF (3200) 83 PSF (4000) 100 PSF (4800) 2 27 8.5 8 24 7.5 5 14 4.5 4 ADMD080EN Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall kawneer.com © Kawneer Company, Inc., 2013 METERS 11-1/4" (285.8) 28 MULLION HEIGHT .5 METERS SINGLE SPAN A= B= C= D= E= Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. MULLION HEIGHT IN FEET 32 EC 97911-095 MAY, 2016 I = 42.441(1766.52 x 104) S = 8.816(144.47 x 103) 171264 GLASS HEIGHT IN FEET © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. kawneer.com 9 8 6 0 0 B 3 0 0 1 1 2 2 3 3 4 4 5 5 6 1 4 6 7 8 7 7 2 5 4 A 1 10 B 2 6 3 GLASS HEIGHT IN FEET 6" (152.4) 171213 METERS 2 13 13 1 12 12 11 11 3 10 8 9 3 5 A 1 8 SPAN IN FEET ADMD080EN 7 6 2 2 1 1 0 13 13 12 12 11 11 2 2 1 1 0 B 4 3 0 0 1 1 2 SPAN IN FEET 7-1/2" (190.5) METERS 2 3 2 3 4 171215 4 5 SPAN IN FEET 5 6 1 5 4 6 7 7 7 2 A 10 B 6 2 A 3 1 8 METERS EC 97911-095 METERS 7 GLASS HEIGHT IN FEET 10 METERS 1 METERS GLASS HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 1600UT SystemTM1 Curtain Wall 33 DEADLOAD CHARTS (TUBULAR) A - 1" GLASS (1/4 POINT LOADING) B - 1" GLASS (1/8 POINT LOADING) 6" (152.4) 171214 METERS 2 9 3 8 5 1 8 SPAN IN FEET 7-1/2" (190.5) 171216 METERS 2 9 3 8 GLASS HEIGHT IN FEET 6 5 4 3 0 0 0 0 1 1 2 2 3 3 4 4 5 5 6 1 5 4 6 171202 2 METERS 13 13 1 12 12 11 11 3 8 7 2 B A 1 2 2 1 1 7 7 8 10 7 3 0 SPAN IN FEET 13 13 12 12 11 11 3 9 8 6 2 A B 1 2 2 1 1 8 0 SPAN IN FEET ADMD080EN 0 0 1 1 2 8-1/4" (209.6) METERS 2 3 2 3 4 171203 4 5 2 10 9 3 8 7 6 2 5 4 B 3 A 1 6 1 3 5 6 7 171204 METERS 2 10 9 3 8 7 6 2 5 B 4 A 7 1 SPAN IN FEET 8 kawneer.com © Kawneer Company, Inc., 2013 171201 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 6-3/4" (171.5) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. DEADLOAD CHARTS (TUBULAR) METERS 1600UT SystemTM1 Curtain Wall METERS 9 GLASS HEIGHT IN FEET 10 GLASS HEIGHT IN FEET 1 METERS METERS METERS GLASS HEIGHT IN FEET 34 EC 97911-095 MAY, 2016 A - 1-3/4" GLASS (1/4 POINT LOADING) B - 1-3/4" GLASS (1/8 POINT LOADING) 6-3/4" (171.5) SPAN IN FEET 8 8-1/4" (209.6) GLASS HEIGHT IN FEET © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. kawneer.com 9 8 6 0 0 2 5 4 3 2 1 A 0 0 1 1 2 2 3 3 4 4 5 5 6 1 4 3 6 7 10 7 6 2 5 A 7 GLASS HEIGHT IN FEET 171296 171292 (DOTTED) METERS 2 13 13 1 12 12 11 11 3 10 1 B 8 9 3 8 B 1 8 SPAN IN FEET ADMD080EN 7 6 0 13 13 12 12 11 11 2 2 1 1 0 2 3 2 A B SPAN IN FEET 0 0 1 1 2 METERS 2 3 2 3 4 4 5 SPAN IN FEET 5 6 1 5 4 6 7 10 7 6 3 7 8 METERS EC 97911-095 2 B A 1 METERS 7 GLASS HEIGHT IN FEET 10 METERS 1 METERS GLASS HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 1600UT SystemTM1 Curtain Wall 35 DEADLOAD CHARTS (OPENBACK) A - 1" GLASS (1/4 POINT LOADING) B - 1" GLASS (1/8 POINT LOADING) 171297 171293 (DOTTED) METERS 2 9 3 8 5 4 1 1 SPAN IN FEET 8 171296 171292 (DOTTED) 171297 171293 (DOTTED) 171077 REINF. 171078 REINF. METERS 2 9 3 8 GLASS HEIGHT IN FEET 4 3 2 1 0 0 0 0 1 1 2 2 3 3 4 4 5 5 6 1 7 6 4 3 6 METERS 2 METERS 13 13 1 12 12 11 11 3 8 6 2 5 B 1 A 7 7 8 10 B A 0 SPAN IN FEET 13 13 12 12 11 11 9 3 8 2 5 1 2 2 1 1 8 0 SPAN IN FEET ADMD080EN 0 0 1 1 2 METERS 2 3 2 3 2 10 9 3 8 7 6 2 5 4 3 2 B 1 A 4 4 5 6 1 5 6 7 10 8 7 B 6 2 4 3 A 7 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 171295 171291 (DOTTED) 171294 171290 (DOTTED) 171295 171291 (DOTTED) 171077 REINF. 171078 REINF. METERS 2 9 3 5 1 SPAN IN FEET 8 kawneer.com © Kawneer Company, Inc., 2013 171294 171290 (DOTTED) METERS DEADLOAD CHARTS (OPENBACK) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 9 GLASS HEIGHT IN FEET 1600UT SystemTM1 Curtain Wall METERS 7 GLASS HEIGHT IN FEET 10 METERS 1 METERS GLASS HEIGHT IN FEET 36 EC 97911-095 MAY, 2016 A - 1" GLASS (1/4 POINT LOADING) B - 1" GLASS (1/8 POINT LOADING) 1 SPAN IN FEET 8 GLASS HEIGHT IN FEET © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. kawneer.com 9 0 0 3 8 6 2 5 4 3 2 1 0 0 1 1 2 2 3 3 4 4 5 5 6 1 4 3 6 7 10 7 2 6 5 A 7 GLASS HEIGHT IN FEET 171294 171290 (DOTTED) METERS 2 13 13 1 12 12 11 11 10 1 B A 8 9 3 8 B 1 8 SPAN IN FEET ADMD080EN 7 6 0 13 13 12 12 11 11 2 2 1 1 0 2 3 2 SPAN IN FEET 0 0 1 1 2 METERS 2 3 2 3 4 4 5 6 1 5 4 SPAN IN FEET 5 6 7 10 7 6 2 A B 3 1 7 8 METERS EC 97911-095 METERS 7 GLASS HEIGHT IN FEET 10 METERS 1 METERS GLASS HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 1600UT SystemTM1 Curtain Wall 37 DEADLOAD CHARTS (OPENBACK) A - 1-3/4" GLASS (1/4 POINT LOADING) B - 1-3/4" GLASS (1/8 POINT LOADING) 171295 171291 (DOTTED) METERS 2 9 3 8 5 4 A B 1 1 SPAN IN FEET 8 171294 171290 (DOTTED) 171295 171291 (DOTTED) 171077 REINF. 171078 REINF. METERS 2 9 3 8 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall BLANK PAGE ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 38 EC 97911-095 MAY, 2016 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of Glass will vary on specific products depending on sitelines) (Based on single bay of Curtain Wall/Window Wall) 2-1/2" Typ. 4'-0" 3'-0" D.L.O. D.L.O. VISION VISION 6'-0" D.L.O. SPANDREL 9'-0" D.L.O. 31'-3" 8'-0" D.L.O. SPANDREL VISION 5'-0" D.L.O. Vision Area Example Glass U-factor = 0.48 Btu/(ft2 · h · °F) Vision Area = 5(9 + 8 + 4) = 105.0 ft2 Total Area (Vision) = 5' 2-1/2" (9' 3-3/4" + 8' 2-1/2" + 4' 2-1/2") = 113.2 ft2 Percentage of Vision Glass = (Vision Area ÷ Total Area)100 = (105.0 ÷ 113.2)100 = 93% © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2-1/2" Typ. Spandrel Area Example Spandrel R-value = 15 (ft2 · h · °F)/Btu Spandrel Area = 5(6 + 3) = 45.0 ft2 Total Area (Spandrel) = 5' 2-1/2" (6' 2-1/2" + 3' 3-3/4") = 49.6 ft2 Percent of Spandrel kawneer.com = (Spandrel Area ÷ Total Area)100 = (45.0 ÷ 49.6)100 = 91% ADMD080EN 39 40 1600UT SystemTM1 Curtain Wall MAY, 2016 THERMAL CHARTS EC 97911-095 Vision Area Chart System U-factor vs Percent of Vision Area E IGN PL S M E A D EX OR F T COG U-factor 0.53 0.50 0.40 0.30 ) 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 0.20 0.60 Btu h·ft 2·°F System U-factor O (N 0.70 93% 0.20 95 85 90 75 80 70 Vision Area / Total Area (%) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 0.80 System U-factor vs Percent of Spandrel Area Spandrel R-value E IGN PL S M E A D EX OR F O 0.50 T 3.00 4.00 5.00 0.21 0.20 0.10 91% 95 0.30 ) 11.00 15.00 19.00 30.00 0.40 Btu h·ft 2·°F System U-factor (N 2.00 0.60 90 85 80 75 70 Spandrel Area / Total Area (%) Based on a single curtain wall bay of 91% spandrel and center of spandrel R-value of 15, system U-factor is equal to 0.21 Btu/(h·ft 2·°F) ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 Spandrel Area Chart Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Based on a single curtain wall bay of 93% vision glass and center of glass U-factor of 0.48, System U-factor is equal to 0.53 Btu/(h·ft 2·°F) 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 THERMAL CHARTS Note: Values in parentheses are metric. COG=Center of Glass. Charts are generated per AAMA 507. 1" GLAZING WITH ALUMINUM PRESSURE PLATE System U-Factor (Btu/h·ft2·°F) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-Factor for Vision Glass COG U-factor 0.47 (2.67) 0.46 (2.61) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.44 (2.50) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Vision Area / Total Area (%) Notes for System U-Factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values (winter conditions) and are obtained from your glass supplier. kawneer.com ADMD080EN 41 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Ares / Total Area (%) Charts are generated per AAMA 507. ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC 1600UT SystemTM1 Curtain Wall Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 42 EC 97911-095 MAY, 2016 1" GLAZING WITH ALUMINUM PRESSURE PLATE Vision Area / Total Area (%) Charts are generated per AAMA 507. 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 THERMAL PERFORMANCE MATRIX (NFRC SIZE) 1" GLAZING WITH ALUMINUM PRESSURE PLATE Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Overall U-Factor 4 0.47 0.54 0.46 0.53 0.44 0.52 0.42 0.50 0.40 0.48 0.38 0.47 0.36 0.45 0.34 0.43 0.32 0.42 0.30 0.40 0.28 0.38 0.26 0.37 0.24 0.35 0.22 0.33 0.20 0.32 0.18 0.30 0.16 0.28 0.14 0.26 0.12 0.25 0.10 0.23 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 kawneer.com 43 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 2000mm wide by 2000mm high (78-3/4" by 78-3/4"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.68 0.75 0.67 0.70 0.64 0.70 0.63 0.65 0.59 0.65 0.58 0.60 0.55 0.60 0.54 0.55 0.50 0.55 0.49 0.50 0.46 0.50 0.45 0.45 0.41 0.45 0.40 0.40 0.37 0.40 0.36 0.35 0.32 0.35 0.31 0.30 0.28 0.30 0.27 0.25 0.24 0.25 0.22 0.20 0.19 0.20 0.18 0.15 0.15 0.15 0.13 0.10 0.10 0.10 0.09 0.05 0.06 0.05 0.04 ADMD080EN 44 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 THERMAL CHARTS Note: Values in parentheses are metric. COG=Center of Glass. Charts are generated per AAMA 507. 1" GLAZING WITH FIBERGLASS PRESSURE PLATE 0.47 (2.67) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Vision Area / Total Area (%) Notes for System U-Factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values (winter conditions) and are obtained from your glass supplier. ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 COG U-factor Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System U-Factor (Btu/h·ft2·°F) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-Factor for Vision Glass System VT © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 kawneer.com 1600UT SystemTM1 Curtain Wall EC 97911-095 Vision Ares / Total Area (%) Charts are generated per AAMA 507. ADMD080EN 45 THERMAL CHARTS 1" GLAZING WITH FIBERGLASS PRESSURE PLATE System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) Charts are generated per AAMA 507. System Visible Transmittance (VT) vs Percent of Vision Area COG VT 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 THERMAL PERFORMANCE MATRIX (NFRC SIZE) Overall U-Factor 4 0.47 0.53 0.46 0.52 0.44 0.50 0.42 0.49 0.40 0.47 0.38 0.45 0.36 0.44 0.34 0.42 0.32 0.40 0.30 0.39 0.28 0.37 0.26 0.35 0.24 0.34 0.22 0.32 0.20 0.31 0.18 0.28 0.16 0.27 0.14 0.25 0.12 0.23 0.10 0.22 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 2000mm wide by 2000mm high (78-3/4" by 78-3/4"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.68 0.75 0.67 0.70 0.64 0.70 0.63 0.65 0.59 0.65 0.58 0.60 0.55 0.60 0.54 0.55 0.50 0.55 0.49 0.50 0.46 0.50 0.45 0.45 0.41 0.45 0.40 0.40 0.37 0.40 0.36 0.35 0.32 0.35 0.31 0.30 0.28 0.30 0.27 0.25 0.24 0.25 0.22 0.20 0.19 0.20 0.18 0.15 0.15 0.15 0.13 0.10 0.10 0.10 0.09 0.05 0.06 0.05 0.04 ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 Glass U-Factor 3 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1" GLAZING WITH FIBERGLASS PRESSURE PLATE Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 46 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 THERMAL CHARTS Note: Values in parentheses are metric. COG=Center of Glass. Charts are generated per AAMA 507. 1-3/4" GLAZING WITH ALUMINUM PRESSURE PLATE System U-Factor (Btu/h·ft2·°F) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-Factor for Vision Glass 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) 0.08 (0.45) © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. COG U-factor Vision Area / Total Area (%) Notes for System U-Factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values (winter conditions) and are obtained from your glass supplier. kawneer.com ADMD080EN 47 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Ares / Total Area (%) Charts are generated per AAMA 507. ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC 1600UT SystemTM1 Curtain Wall Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 48 EC 97911-095 MAY, 2016 1-3/4" GLAZING WITH ALUMINUM PRESSURE PLATE Vision Area / Total Area (%) Charts are generated per AAMA 507. 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 THERMAL PERFORMANCE MATRIX (NFRC SIZE) 1-3/4" GLAZING WITH ALUMINUM PRESSURE PLATE Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Overall U-Factor 4 0.32 0.42 0.30 0.40 0.28 0.38 0.26 0.37 0.24 0.35 0.22 0.33 0.20 0.32 0.18 0.30 0.16 0.28 0.14 0.26 0.12 0.25 0.10 0.23 0.08 0.21 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 kawneer.com 49 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 2000mm wide by 2000mm high (78-3/4" by 78-3/4"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.68 0.75 0.67 0.70 0.64 0.70 0.63 0.65 0.59 0.65 0.58 0.60 0.55 0.60 0.54 0.55 0.50 0.55 0.49 0.50 0.46 0.50 0.45 0.45 0.41 0.45 0.40 0.40 0.37 0.40 0.36 0.35 0.32 0.35 0.31 0.30 0.28 0.30 0.27 0.25 0.24 0.25 0.22 0.20 0.19 0.20 0.18 0.15 0.15 0.15 0.13 0.10 0.10 0.10 0.09 0.05 0.06 0.05 0.04 ADMD080EN 50 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 THERMAL CHARTS Note: Values in parentheses are metric. COG=Center of Glass. Charts are generated per AAMA 507. 1-3/4" GLAZING WITH FIBERGLASS PRESSURE PLATE 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) 0.08 (0.45) Vision Area / Total Area (%) Notes for System U-Factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values (winter conditions) and are obtained from your glass supplier. ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 COG U-factor Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System U-Factor (Btu/h·ft2·°F) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-Factor for Vision Glass System VT © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 kawneer.com 1600UT SystemTM1 Curtain Wall EC 97911-095 Vision Ares / Total Area (%) Charts are generated per AAMA 507. ADMD080EN 51 THERMAL CHARTS 1-3/4" GLAZING WITH FIBERGLASS PRESSURE PLATE System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) Charts are generated per AAMA 507. System Visible Transmittance (VT) vs Percent of Vision Area COG VT 1600UT SystemTM1 Curtain Wall MAY, 2016 EC 97911-095 THERMAL PERFORMANCE MATRIX (NFRC SIZE) Overall U-Factor 4 0.32 0.41 0.30 0.39 0.28 0.37 0.26 0.36 0.24 0.34 0.22 0.32 0.20 0.31 0.18 0.29 0.16 0.27 0.14 0.25 0.12 0.24 0.10 0.22 0.08 0.20 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 2000mm wide by 2000mm high (78-3/4" by 78-3/4"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.68 0.75 0.67 0.70 0.64 0.70 0.63 0.65 0.59 0.65 0.58 0.60 0.55 0.60 0.54 0.55 0.50 0.55 0.49 0.50 0.46 0.50 0.45 0.45 0.41 0.45 0.40 0.40 0.37 0.40 0.36 0.35 0.32 0.35 0.31 0.30 0.28 0.30 0.27 0.25 0.24 0.25 0.22 0.20 0.19 0.20 0.18 0.15 0.15 0.15 0.13 0.10 0.10 0.10 0.09 0.05 0.06 0.05 0.04 ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 Glass U-Factor 3 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1-3/4" GLAZING WITH FIBERGLASS PRESSURE PLATE Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 52 © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MAY, 2016 kawneer.com 1600UT SystemTM1 Curtain Wall EC 97911-095 PRESSURE PLATE TYPE CRF FRAME GLASS I-VALUE FRAME GLASS 1" DOUBLE GLAZING INFILL ALUMINUM FIBERGLASS 7976 7167 76 68 1-3/4" TRIPLE GLAZING INFILL ALUMINUM FIBERGLASS 82 74 76 ADMD080EN 81 53 THERMAL CHARTS CONDENSATION RESISTANCE 77 78 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1600UT SystemTM1 Curtain Wall BLANK PAGE ADMD080EN kawneer.com © Kawneer Company, Inc., 2013 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 54 EC 97911-095 MAY, 2016