Product Specification Dimensions HXC20/40 F-Mount HXC cameras - Maximum Performance with CMOSIS sensors UNC 1/4-20 ▪▪ Camera Link Full progressive scan CMOS camera ▪▪ Excellent image quality ▪▪ Global shutter architecture for minimized motion blur ▪▪ Low noise due to correlated double sampling (CDS) ▪▪ HDR (High Dynamic Range) ▪▪ Enhanced NIR sensitivity model available ▪▪ Binning, subsampling and true partial scan function (ROI) for increased frame rates ▪▪ External synchronization via industrial compliant process interface (trigger / flash) ▪▪ Integrated supplementary function for flexible integration ▪▪ Integrated 256 MByte RAM for temporarily image data buffering ▪▪ Two standard 26 pin Mini-CameraLink® connectors ▪▪ Support for CameraLink® Base, Medium, Full and 10 tap configurations ▪▪ Baumer GAPI: Flexible, generic software interface for Windows 26 36 ® 36 26 52 16 x M3 depth 6 37 Camera Type Quick Start Guide HXC cameras – Release 2 (Camera Link®) Resolution Full Frames [max. fps] 2/3“ 1“ 2048 x 1088 2048 x 2048 337 180 2/3“ 1“ 2048 x 1088 2048 x 2048 337 180 Monochrome HXC20 HXC40 Color HXC20c HXC40c Latest software version and technical documentation are available at: 36 26 52 Sensor Size www.baumer.com/vision/login Conformity: Installation using Camera Link® BASE: See User´s Guide for the complete safety instructions! ▪▪ If required, connect a strobe to the connector ▪▪ Protect the sensor from dirt and moisture. ▪▪ Never open the camera housing. ▪▪ Avoid camera contamination by foreign objects. ▪▪ Connect the camera to power supply Environmental requirements: Installation using Camera Link® MEDIUM / FULL: Storage temp. Operating temp. Housing temp. Humidity -10 °C ... +70 °C (14 °F...158 °F) +5 °C ... +60 °C (41 °F...140 °F) max. +65 °C (max. 149 °F) 10 % ... 90 % Non-condensing Further Information For further information on our products visit www.baumer.com For technical issues, please contact our technical support: [email protected]· Phone +49 (0)3528 4386-0 · Fax +49 (0)3528 4386-86 © Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany Technical data has been fully checked, but accuracy of printed cannot be guaranteed. Subject to change without notice. Printed in Germany 06/14. v1.7 11054752 36 16 x M3 depth 6 Installation sample 1 - Framegrabber board; 2 - CameraLink® cable; 3 - Process interface cable; 4 - Power cable ▪▪ If required, connect a strobe to the connector ▪▪ Connect the camera to power supply 37,4 52 ▪▪ Connect the camera using two appropriate cables to the framegrabber board on your PC (this configuration requires the BASE and the FULL Camera Link® line) Installation sample 1 - Framegrabber board; 2 - CameraLink® cable; 3 - Process interface cable; 4 - Power cable 36 Notice 36 Safety instructions 36 26 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructios, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occure in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures: ▪▪ Reorient or relocate the receiving antenna. ▪▪ Increase the separation between the equipment and the receiver. ▪▪ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ▪▪ Consult the dealer or an experienced radio/TV technician for help. ▪▪ Connect the camera using an appropriate cable to the framegrabber board on your PC using the lower sdr-26 jack on the camera side 36 26 FCC – Class B device UNC 1/4-20 52 CE, FCC Part 15 Class B, RoHS Dimensions HXC20/40 C-Mount 4 x M3 depth 6 Installation 26 Safety General Description LED Signaling 1 Heat Transmission 3 2 Caution Provide adequate dissipation of heat, to ensure that the temperature does not exceed the spedified temperature. The surface of the camera may be hot during operation and immediately after use. Be careful when handling the camera and avoid contact over a longer period. 1 4 2 T It is very important to provide adequate dis- T housing sipation of heat, to ensure that the temperature does not reach or exceed +65 °C 6 No. 1 Description 5 No. (respective) lens mount 4 (+149°F). As there are numerous possibilities for installation, a specific method for proper heat disDescription LED Digital-IO supply Signal Meaning green Power on yellow Readout active green Transmitting red (yellow in both) Configuration comman processing 1 2 Power supply 5 CameraLink® Base socket 3 CameraLink® Full socket 6 Signaling-LED 2 sipation is not defined, but the following principles T: Housing temperature measurement point are suggested: ▪▪ Operate the cameras only in mounted condition with a good heat conductor (e.g. aluminum) ▪▪ Mounting in combination with forced convection may provide proper heat dissipation Camera Link® Interfaces Power Supply / IO Pin Assignment Notice Caution CL FULL Baumer Type: HXCXXx (xxxxxxx) R1.0 S/N: 000XXXXX CL BASE The camera has two CameraLink sockets. To differentiate between CameraLink Base and CamerLink Full socket, please look at the label. You can not use the CL Full socket alone! A power supply with electrical isolation is required for proper operation of the camera. Otherwise the device may be damaged. M8 / 3 pins Caution wire colors of the connecting cable When fixing the CameraLink® cable with too much force the screws might get damaged. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Signal GND X0X1X2XCLKX3SERTC+ SERTFGCC1CC2+ CC3CC4+ GND Pin 14 15 16 17 18 19 20 21 22 23 24 25 26 Signal GND X0+ X1+ X2+ XCLK+ X3+ SERTCSERTFG+ CC1+ CC2CC3+ CC4GND Signal GND Y0Y1Y2YCLKY3100 Ω term. Z0Z1Z2ZCLKZ3GND Pin 14 15 16 17 18 19 20 21 22 23 24 25 26 Signal GND Y0+ Y1+ Y2+ YCLK+ Y3+ 100 Ω term. Z0+ Z1+ Z2+ ZCLK+ Z3+ GND 5 4 7 3 1 4 Full Camera Link® Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 6 1 3 The maximum torque is 2.5 inch lbf [0.3 Nm]. Base Camera Link® M8 / 8 pins 8 2 1 (brown) Power VCC 1 (white) Line 9 3 (blue) GND 2 (brown) Line 1 4 (black) NC 3 (green) Line 0 4 (yellow) GND 5 (grey) Uext 6 (pink) Line 7 7 (blue) Line 8 8 (red) Line 2 Power Supply Power VCC 9,6 VDC .. 30 VDC I 200 mA .. 625 mA