miniaturization of TVS or EOS protection devices

USB Power Delivery
Advanced protection solutions
Fundamentals
Is this presentation suited for you?
Where do you stand with USB Power Delivery?
Beginner?
Intermediate?
Advanced?
I am not familiar with this
subject. I am in the
discovery phase and would
like an overview and a
basic understanding of the
technology.
I have a basic
understanding of this
subject. I would like to go
deeper in details and tackle
more aspects of this
subject.
I am very familiar with this
subject. I would like to
deepen my knowledge and
become an expert.
Click here to continue
to next slide
Click here to continue
to next slide
Click here to continue
to next slide
Overview
Fundamentals
In depth
2
Power over USB
• The success of the USB Battery Charging standard for
mobile devices demonstrated the need for a standardized
connector to power small devices.
• To power up bigger devices like SSD/HDD, laptops or even
screens, it is necessary to reach power up to 100 W.
3
A new specification
• The USB Power Delivery specification V1.1 was released
on May 7, 2015 to address these needs.
• This specification is an extension to the existing
USB 2.0, USB 3.1, USB Type-C and Battery Charging
specifications covering only the elements required to
implement USB Power Delivery.
4
Profiles
• 6 power profiles are defined extending the supply voltages (profile 0 is reserved)
• This requires new cables withstanding voltages higher than 5 V and currents
higher than 1.5 A.
• Profile 4 is the limit for the micro-B/AB connector.
Profile
5V
12 V
20 V
1
2
3
4
5
1.5 A, 18 W
2.0 A, 10 W
3.0 A, 36 W
5.0 A, 60 W
3.0 A, 60 W
5.0 A, 100 W
5
VBUS voltage and current
• Sources with 100 W operation capability must meet various worldwide
safety standards. As such, the continuous output power cannot exceed
100 W and the continuous output current cannot exceed 5 A.
Interpretation of the safety requirements imposed by IEC/UL 60950
5
3
1
2
4
Profile 1 : up to
1
Profile 2: up to
1
2
Profile 3: up to
1
3
Profile 4: up to
1
3
4
Profile 5: up to
1
3
5
6
More power means more protection
• With USB power capability increasing, the risks of
surges and transients must be properly mitigated.
• Portable devices often implement miniature ICs
using the thinnest - and more vulnerable technologies.
• The power sources are not controlled by the
portable device manufacturers, so the need to
protect power ports is obvious.
Two types of hazards:
• ESD hazards
• Lightning and industrial surges
7
ESD protection needed …
Advanced technology with very thin lithography
and gate oxide highly vulnerable to ESD
Integrated electronics systems with high
component-density PCBs facilitating ESD
coupling and propagation
USB transceivers, controllers …
IC manufacturers reluctant to use robust
embedded ESD protection diodes that would
require a significant active area of their advanced
and expensive technology.
8
And surge protection too
Experiments and measurements have demonstrated that the current waveform of a
lightning strike or switching noise has a rise time close of 8 µs to reach the peak.
==> The IEC/UL 61000-4-5 has provided a standardized current waveform called
8/20 µs waveform modeling lightning stresses or switching noise.
The key performance factor for a VBUS protection is the clamping
voltage versus 8/20 µs surges (IEC/UL 61000-4-5 standard)
9
A wide portfolio
ESD PROTECTION
 IEC/UL 61000-4-2 Level 4 (+8 kV contact)
VBUS
SMALLEST
10
ESD & EOS PROTECTION
+ EN 55024 / CISPR 24 (IPP 8/20µs > 59 A)
+ IEC/UL 61000-4-5
HIGH POWER
DENSITY
STRONGEST
Typ.
20 V
ESDALC20-1BF4
SMM4F24A
VCL @ 30 ns = 37 V
IPP = 2.4 A, PPP = 90 W
VCL 8/20 µs = 58 V
IPP = 60 A, PPP = 2300 W
SMM4F13A
12 V
VCL 8/20 µs = 24 V
IPP = 85 A, PPP = 2300 W
ESDALC14-1BF4
9V
VCL @ 30 ns = 18 V
IPP = 5 A, PPP = 100 W
ESDA5-1BF4
5V
VCL @ 30 ns = 11 V
IPP = 10 A, PPP = 110 W
0201
ESDA13P70-1U1M
VCL 8/20 µs = 20 V
IPP = 70 A, PPP = 1300 W
ESDA7P60-1U1M
VCL 8/20 µs = 12 V
IPP = 60 A, PPP = 700 W
VCL 8/20 µs = 20 V
IPP = 100 A, PPP = 2200 W
SMM4F6.0A
VCL 8/20 µs = 10 V
IPP = 170 A, PPP = 2300 W
STmiteFLAT
1610
0.3 mm
SMM4F12AVCL
0.55 mm
Package
& Size
0.85 mm
Zoom on ESDA7P60-1U1M
Small but robust
•
•
100
IPP (A)
Can withstand 30 kV contact discharge
ESD strikes
A high transient current (IPP 60 A for 8/20
µs) in a small 1.6 mm² package .
Low VCL
10
Max clamping voltage VCL
1
11.6 V at 60A
USB transceiver is safe!
•
This product is able to keep the overvoltage
at 11.6 V while shunting 60 A to the GND.
1610 package
VCL(V)
0.1
6
10
12
Constant PPP guaranteed over T°
Strong even at high temperature
•
8
Peak pulse power guaranteed up to 150 °C.
1000
PPP (W)
750
Electrical parameters
Symbol
Test
Condition
8/20 µs
Min PPP= 700 W
500
Min.
Typ.
Max.
Units
6.4
6.8
7.2
200
V
250
VBR
IR = 1 mA
IRM
VRM = 5 V
nA
Tj( C)
0
25
50
75
100
125
150
175
11
Let’s go further
Overview
information
Fundamentals
In-depth
information
Selection &
sampling
12
 USB type-C™ advanced protection quick start guide
 USB2.0 protection and IPADTM solutions presentation
 USB type-C™ dataline advanced protection presentation
 IEC 61000-4-5 standard overview Application note #AN4275
 ESD - IEC 61000-4-2 standard testing
Application note #AN3353
 TVS short pulse dynamic resistance measurement ... Application note #AN4022
 Protection devices & integrated EMI filtering selection guide
 USB port protection web product selector
 USB IPAD™ (including ECMF™) web product selector
Thank you