SFH628A, SFH6286 www.vishay.com Vishay Semiconductors Optocoupler, Phototransistor Output, AC Input, Low Input Current FEATURES • High common mode interference immunity • Isolation test voltage, 5300 VRMS • Low coupling capacitance 1 A/C 1 4 C C/A 2 3 E • Good CTR linearity depending on forward current • Low CTR degradation 1 V D E i179080-3 • High collector emitter voltage, VCEO = 55 V 1 • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 DIP-4 SMD-4 pin groove APPLICATIONS 1 DESCRIPTION • Telecom The SFH628A (DIP) and SFH6286 (SMD) feature a high current transfer ratio, low coupling capacitance and high isolation voltage. These couplers have a GaAs infrared emitting diode, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a plastic DIP-4 or SMD package. • Industrial controls • Battery powered equipment • Office machines AGENCY APPROVALS • UL1577, file no. E52744 system code H The coupling devices are designed for signal transmission between two electrically separated circuits. • DIN EN 60747-5-5 (VDE0884-5), available with option 1 • BSI IEC 60950; IEC 60065 The couplers are end-stackable with 2.54 mm lead spacing. Creepage and clearance distances of > 8 mm are achieved with option 6. This version complies with IEC 60950 (DIN VDE 0805) for reinforced insulation to an operation voltage of 400 VRMS or DC. ORDERING INFORMATION DIP-# S F H 6 2 8 x - # X 0 # # T 7.62 mm PART NUMBER CTR BIN PACKAGE OPTION TAPE AND REEL Option 6 10.16 mm Option 8 9.27 mm > 0.7 mm SFH6286 Option > 0.1 mm CTR (%) AGENCY CERTIFIED/ PACKAGE UL, BSI Option 7 SFH628A SFH6286 63 to 200 100 to 320 160 to 500 63 to 200 100 to 320 SFH628A-2T (1) SFH628A-3 SFH628A-4 - - - - - - SFH6286-2T (1) SFH6286-3T (1) SFH6286-4T (1) 63 to 200 100 to 320 160 to 500 63 to 200 100 to 320 160 to 500 - SFH628A-3X001 - - - - DIP-4, 400 mil, option 6 SFH628A-2X016 SFH628A-3X016 SFH628A-4X016 - - - SMD-4, option 7 - SFH628A-3X017T - - - - SMD-4, option 8 SFH628A-2X018 - - - - - SFH6286 option - - - DIP-4 SFH6286 option VDE, UL, BSI DIP-4 160 to 500 SFH6286-2X001T SFH6286-3X001T SFH6286-4X001T (1) Notes • Additional options may be possible, please contact sales office. (1) Also available in tubes; do not add T to end. Document Number: 83722 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.1, 28-Feb-14 SFH628A, SFH6286 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT t ≤ 10 μs IF ± 50 mA IFSM ± 2.5 A Pdiss 76 mW Collector emitter voltage VCEO 55 V Emitter collector voltage VECO 7 V INPUT DC forward current Surge forward current Power dissipation OUTPUT Collector current tp ≤ 1 ms Power dissipation IC 50 mA IC 100 mA Pdiss 150 mW VISO 5300 VRMS COUPLER Isolation test voltage Creepage distance ≥7 mm Clearance distance ≥7 mm ≥ 0.4 mm Insulation thickness between Comparative tracking index per DIN IEC112/ 175 Isolation resistance VIO = 500 V, Tamb = 25 °C RIO ≥ 1012 VIO = 500 V, Tamb = 100 °C RIO ≥ 1011 Ω Tstg -55 to +150 °C Tamb -55 to +100 °C Tsld 260 °C Storage temperature range Ambient temperature range Soldering temperature (1) max. 10 s, dip soldering distance Ω Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. 1.5 UNIT INPUT Forward voltage Capacitance IF = ± 5 mA VF 1.1 VR = 0 V, f = 1 MHz CO 45 pF Rthja 1070 K/W VCE = 10 V ICEO 10 VCE = 5 V, f = 1 MHz CCE 7 pF Rthja 500 K/W SFH628A-2 VCEsat 0.25 0.4 V SFH6286-2 VCEsat 0.25 0.4 V SFH628A-3 VCEsat 0.25 0.4 V SFH6286-3 VCEsat 0.25 0.4 V SFH628A-4 VCEsat 0.25 0.4 V SFH6286-4 VCEsat 0.25 0.4 V Thermal resistance V OUTPUT Collector emitter leakage current Collector emitter capacitance Thermal resistance 200 nA COUPLER IF = ± 1 mA, IC = 0.5 mA Collector emitter saturation voltage IF = ± 1 mA, IC = 0.8 mA IF = ± 1 mA, IC = 1.25 mA Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Document Number: 83722 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.1, 28-Feb-14 SFH628A, SFH6286 www.vishay.com Vishay Semiconductors CURRENT TRANSFER RATIO (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION IF = ± 1 mA, VCE = 0.5 V IF = ± 0.5 mA, VCE = 1.5 V IF = ± 1 mA, VCE = 0.5 V IC/IF IF = ± 0.5 mA, VCE = 1.5 V IF = ± 1 mA, VCE = 0.5 V IF = ± 0.5 mA, VCE = 1.5 V PART SYMBOL MIN. SFH628A-2 CTR 63 TYP. SFH6286-2 CTR 63 SFH628A-2 CTR 32 100 100 SFH6286-2 CTR 32 CTR 100 SFH6286-3 CTR 100 SFH628A-3 CTR 50 160 160 SFH6286-3 CTR 50 CTR 160 UNIT 200 % 200 SFH628A-3 SFH628A-4 MAX. % % % 320 320 % % % % 500 500 % SFH6286-4 CTR 160 SFH628A-4 CTR 80 250 % % SFH6286-4 CTR 80 250 % SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL Turn-on time VCC = 5 V, IC = 2 mA, RL = 100 Ω ton 6 μs Rise time VCC = 5 V, IC = 2 mA, RL = 100 Ω tr 3.5 μs Turn-off time VCC = 5 V, IC = 2 mA, RL = 100 Ω toff 5.5 μs Fall time VCC = 5 V, IC = 2 mA, RL = 100 Ω tf 5 μs ± IF RL MIN. TYP. MAX. VCC UNIT Input pulse IC 10 % Output pulse 90 % tr 47 Ω tf t off t on isfh618a_12 isfh618a_11 Fig. 1 - Test Circuit Fig. 2 - Test Circuit and Waveforms SAFETY AND INSULATION RATINGS PARAMETER Climatic classification TEST CONDITION SYMBOL MIN. according to IEC 68 part 1 Comparative tracking index TYP. MAX. UNIT 55/100/21 CTI 175 399 VIOTM 10000 V VIORM 890 V PSO 400 mW ISI 275 mA TSI 175 °C Creepage distance Standard DIP-8 7 mm Clearance distance Standard DIP-8 7 mm Creepage distance 400 mil DIP-8 8 mm 400 mil DIP-8 8 mm per IEC 60950 2.10.5.1 0.4 mm Clearance distance Insulation thickness, reinforced rated Note • As per IEC 60747-5-5, § 7.4.3.8.1, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. Document Number: 83722 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.1, 28-Feb-14 SFH628A, SFH6286 www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 1.2 280 IF = 1.0 mA, VF = f (TA) 1.15 200 VF (V) CTR (%) 240 VCE = 0.5 V, CTR = f (TA) IF = 5mA 160 1.05 120 IF = 2mA 80 IF = 1mA 40 IF = 0.5mA 0 - 40 - 20 1.1 0 20 isfh618a_01 40 60 TA (°C) 80 1 0.95 0 - 40 - 20 100 isfh618a_04 Fig. 3 - Current Transfer Ratio (typ.) CCE (pF) CTR (%) 200 IF = 5mA 160 100 120 IF = 2mA 80 IF = 1mA 40 IF = 0.5mA 0 20 40 60 TA (°C) 80 12 8 4 0 10-2 100 10-1 isfh618a_05 Fig. 4 - Current Transfer Ratio (typ.) 100 101 VCE (V) 102 Fig. 7 - Transistor Capacitance 1.2 12 TA = 25 ºC, VF = f (IF) 1.1 1.05 IF = 5 mA TA = 25 ºC, CE = f (VCE, IF) 10 ICE (mA) VF (V) 80 TA = 25 ºC, f = 1.0 MHz CEE = f (VCE) 16 1.15 40 60 TA (°C) 20 240 isfh618a_02 20 Fig. 6 - Diode Forward Voltage (typ.) 280 0 - 40 - 20 0 8 6 1 4 IF = 2 mA 0.95 2 IF = 1 mA 0.9 10-1 isfh618a_03 IF = 0.5 mA 100 IF (mA) Fig. 5 - Diode Forward Voltage (typ.) 101 0 10-2 isfh618a_06 10-1 100 VCE (V) 101 102 Fig. 8 - Output Characteristics Document Number: 83722 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.1, 28-Feb-14 SFH628A, SFH6286 www.vishay.com Vishay Semiconductors 100 103 t (µs) /F (mA) t off IF = f (TA) 75 50 tF 102 t on tR 101 25 0 0 25 50 TA (°C) isfh618a_07 75 TA = 25 ºC, IF = 1.0 mA, VCC = 5.0 V, tON, tR, tOFF, tF, = f (RL) 100 102 100 103 isfh618a_09 Fig. 9 - Permissible Forward Current Diode 104 RL (Ω) 105 Fig. 11 - Switching Times (Typ.) 200 Ptot = f (TA) Ptot (mW) 175 150 125 Transistor 100 75 50 Diode 25 0 0 isfh618a_08 25 50 75 TA (°C) 100 Fig. 10 - Permissible Power Dissipation PACKAGE DIMENSIONS in millimeters 6.48 6.81 Pin 1 identification 4.55 4.83 ISO method A 0.76 1.14 0.79 typ. 7.62 typ. 1.27 typ. 3.30 3.81 5.84 6.35 10° 4° typ. 0.508 0.89 0.46 0.56 1.27 2.79 3.30 0° to 15° 0.2 0.3 2.54 i178027-8 Document Number: 83722 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.1, 28-Feb-14 SFH628A, SFH6286 www.vishay.com Vishay Semiconductors Option 6 Option 7 Option 8 SFH6286 Option 7.62 typ. 7.62 typ. 7.62 typ. 9.52 10.03 7.52 7.90 3.5 ± 0.3 0.7 min. 0.25 ± 0.1 4.3 ± 0.3 3.5 ± 0.3 0.1 min. 0.25 typ. 8 min. 2.55 ± 0.25 9.27 min. 0.6 min. 10.3 max. 0.508 1.020 8 min. 12.1 max. 11.05 1.52 9.95 min. 13 1.78 8 min. 1.78 1.52 0.76 R 0.25 R 0.25 1.52 8 min. 11.05 1.78 R 0.25 2.54 0.76 2.54 0.76 2.54 10.16 typ. PACKAGE MARKING (Example) YWW H 68 SFH628A-3 V X001 Notes • Only options 1, 7, and 8 are reflected in the package marking. • The VDE logo is only marked on option1 parts. • Tape and reel suffix (T) is not part of the package marking. Document Number: 83722 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.1, 28-Feb-14 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000