SFH620A, SFH6206 www.vishay.com Vishay Semiconductors Optocoupler, Phototransistor Output, AC Input FEATURES A/C 1 4 C C/A 2 3 E • Good CTR linearity depending on forward current • Isolation test voltage, 5300 VRMS • High collector emitter voltage, VCEO = 70 V • Low saturation voltage • Fast switching times • Low CTR degradation • Temperature stable • Low coupling capacitance • End-stackable, 0.100" (2.54 mm) spacing • High common-mode interference immunity • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 DESCRIPTION The SFH620A (DIP) and SFH6206 (SMD) feature a high current transfer ratio, low coupling capacitance and high isolation voltage. These couplers have a GaAs infrared diode emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a plastic DIP-4 or SMD package. The coupling devices are designed for signal transmission between two electrically separated circuits. The couplers are end-stackable with 2.54 mm lead spacing. Creepage and clearance distances of > 8 mm are achieved with option 6. This version complies with IEC 60950 (DIN VDE 0805) for reinforced insulation to an operation voltage of 400 VRMS or DC. AGENCY APPROVALS The safety application model number covering all products in this datasheet is SFH620A and SHF6206. This model number should be used when consulting safety agency documents. • UL1577, file no. E52744 system code H, double protection • CSA 93751 • BSI EN 60950, EN 60065 • DIN EN 60747-5-5 (VDE 0884-5), available with option 1 • CQC GB8898-2011, GB4943.1-2011 ORDERING INFORMATION S F H 6 2 0 x - PART NUMBER # X CTR BIN 0 # # PACKAGE OPTION DIP-# Option 6 7.62 mm 10.16 mm Option 7 Option 9 T TAPE AND REEL > 0.7 mm CTR (%) AGENCY CERTIFIED/PACKAGE UL, cUL, BSI DIP-4 > 0.1 mm ± 10 mA SFH620A SFH6206 40 to 125 63 to 200 100 to 320 40 to 125 63 to 200 100 to 320 SFH620A-1 SFH620A-2 SFH620A-3 - - - SFH620A-2X006 SFH620A-3X006 - - - DIP-4, 400 mil, option 6 SFH620A-1X006 SMD-4, option 7 - SFH620A-2X007T (1) - - - - SMD-4, option 9 - - - SFH6206-1T (1) SFH6206-2T (1) SFH6206-3T (1) VDE, UL, CUL, BSI 40 to 125 63 to 200 100 to 320 40 to 125 63 to 200 100 to 320 SFH620A-1X001 SFH620A-2X001 SFH620A-3X001 - - - DIP-4, 400 mil, option 6 - SFH620A-2X016 SFH620A-3X016 - - - SMD-4, option 7 - SFH620A-2X017T - - - - SMD-4, option 9 - - - - DIP-4 SFH6206-2X001T (1) SFH6206-3X001T (1) Notes • Additional options may be possible, please contact sales office. (1) Also available in tubes; do not add T to end. Rev. 2.3, 31-Aug-15 Document Number: 83675 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620A, SFH6206 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT tp ≤ 10 μs IF ± 60 mA IFSM ± 2.5 A Pdiss 100 mW Collector emitter voltage VCEO 70 V Emitter collector voltage VECO 7 V IC 50 mA IC 100 mA Pdiss 150 mW INPUT DC forward current Surge forward current Power dissipation OUTPUT Collector current tp ≤ 1 μs Power dissipation COUPLER Total power dissipation Ptot 250 mW Storage temperature range Tstg -55 to +150 °C Ambient temperature range Tamb -55 to +100 °C Tj 100 °C Tsld 260 °C Junction temperature Soldering temperature (1) max. 10 s, dip soldering distance to seating plane ≥ 1.5 mm Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. 1.65 UNIT INPUT Forward voltage Capacitance IF = ± 60 mA VF 1.25 VR = 0 V, f = 1 MHz CO 50 pF Rthja 750 K/W CCE 6.8 pF Rthja 500 °C/W VCEsat 0.25 CC 0.2 SFH620A-1 ICEO 2 50 nA SFH6206-1 ICEO 2 50 nA SFH620A-2 ICEO 2 50 nA SFH6206-2 ICEO 2 50 nA SFH620A-3 ICEO 5 100 nA SFH6206-3 ICEO 5 100 nA Thermal resistance V OUTPUT Collector emitter capacitance VCE = 5 V, f = 1 MHz Thermal resistance COUPLER Collector emitter saturation voltage IF = ± 10 mA, IC = 2.5 mA Coupling capacitance Collector emitter leakage current VCE = 10 V 0.4 V pF Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Still air, coupler soldered to PCB or base. Rev. 2.3, 31-Aug-15 Document Number: 83675 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620A, SFH6206 www.vishay.com Vishay Semiconductors CURRENT TRANSFER RATIO (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION VCE = 5 V, IF = ± 10 mA IC/IF VCE = 5 V, IF = ± 1 mA PART SFH620A-1 SFH6206-1 SFH620A-2 SFH6206-2 SFH620A-3 SFH6206-3 SFH620A-1 SFH6206-1 SFH620A-2 SFH6206-2 SFH620A-3 SFH6206-3 SYMBOL CTR CTR CTR CTR CTR CTR CTR CTR CTR CTR CTR CTR MIN. 40 40 63 63 100 100 13 13 22 22 34 34 TYP. MAX. 125 125 200 200 320 320 30 30 45 45 70 70 UNIT % % % % % % % % % % % % RL = 75 Ω IF V CC = 5 V IC 47 Ω isfh620a_08 Fig. 1 - Switching Times Linear Operation (without Saturation) SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Turn-on time Rise time Turn-off time Fall time Cut-off frequency TEST CONDITION RL = 75 Ω, IF = ± 10 mA, VCC = 5 V RL = 75 Ω, IF = ± 10 mA, VCC = 5 V RL = 75 Ω, IF = ± 10 mA, VCC = 5 V RL = 75 Ω, IF = ± 10 mA, VCC = 5 V RL = 75 Ω, IF = ± 10 mA, VCC = 5 V SYMBOL ton tr toff tf tctr MIN. TYP. 3 2 2.3 2 208 MAX. UNIT μs μs μs μs kHz SAFETY AND INSULATION RATINGS PARAMETER Climatic classification Pollution degree Comparative tracking index Maximum rated withstanding isolation voltage Tested withstanding isolation voltage Maximum transient isolation voltage Maximum repetitive peak isolation voltage Isolation resistance Output safety power Input safety current Input safety temperature Creepage distance Clearance distance Creepage distance Clearance distance Creepage distance Clearance distance Insulation thickness TEST CONDITION According to IEC 68 part 1 According to DIN VDE 0109 Insulation group IIIa According to UL1577, t = 1 min According to UL1577, t = 1 s According to DIN EN 60747-5-5 According to DIN EN 60747-5-5 Tamb = 25 °C, VIO = 500 V Tamb = 100 °C, VIO = 500 V SYMBOL CTI VISO VISO VIOTM VIORM RIO RIO PSO ISI TS DIP-4 DIP-4 DIP-4, 400 mil, option 6 DIP-4, 400 mil, option 6 SMD-4, option 7 and option 9 SMD-4, option 7 and option 9 DTI VALUE 55/115/21 2 175 4470 5300 8000 890 ≥ 1012 ≥ 1011 700 400 175 ≥7 ≥7 ≥8 ≥8 ≥7 ≥7 ≥ 0.4 UNIT VRMS VRMS Vpeak Vpeak Ω Ω mW mA °C mm mm mm mm mm mm mm Note • As per DIN EN 60747-5-5, § 7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. Rev. 2.3, 31-Aug-15 Document Number: 83675 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620A, SFH6206 www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 20 103 f = 1 MHz IF = 10 mA, VCC = 5 V IC (%) IF 15 C (pF) 3 2 102 10 1 5 CCE 101 - 25 0 0 25 TA (°C) isfh620a_01 50 10-2 75 Fig. 2 - Current Transfer Ratio (CTR) vs. Temperature 104 IF = 14 mA D=0 0.005 0.01 0.02 20 IF (mA) IF = 12 mA IC (mA) 100 101 Ve (V) IF = 10 mA IF = 8 mA IF = 6 mA 10 103 D= tp T 0.05 0.1 tp IF T Pulse cycle D = parameter 0.2 102 0.5 DC IF = 4 mA IF = 1 mA 102 Fig. 5 - Transistor Capacitance (Typ.) vs. Collector Emitter Voltage 30 0 10-1 isfh620a_04 IF = 2 mA 101 0 5 isfh620a_02 10 VCE (V) 15 10-5 10-4 10-3 10-2 isfh620a_05 Fig. 3 - Output Characteristics (Typ.) Collector Current vs. Collector Emitter Voltage 10-1 tp (s) 100 101 Fig. 6 - Permissible Pulse Handling Capability Forward Current vs. Pulse Width 1.2 200 VF = f (IF) Ptot (mW) VF (V) 25 °C 50 °C 75 °C 1.1 150 Transistor 100 1.0 Diode 50 0.9 10-1 isfh620a_03 100 101 102 IF (mA) Fig. 4 - Diode Forward Voltage (Typ.) vs. Forward Current Rev. 2.3, 31-Aug-15 0 0 isfh620a_06 25 50 75 100 TA (°C) Fig. 7 - Permissible Power Dissipation vs. Ambient Temperature Document Number: 83675 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620A, SFH6206 www.vishay.com Vishay Semiconductors 120 Ptot = f (TA) IF (mA) 90 60 30 0 0 25 50 75 100 TA (°C) isfh620a_07 Fig. 8 - Permissible Diode Forward Current vs. Ambient Temperature PACKAGE DIMENSIONS in millimeters DIP-4, Standard 5.10 max. 7.62 typ. 4.70 ± 0.15 6.60 ± 0.25 0.50 min. 1.27 ± 0.10 0.50 ± 0.10 2.54 typ. Pin one I.D. Rev. 2.3, 31-Aug-15 3.10 ± 0.50 3.55 ± 0.25 0.70 min. 4 3 1 2 .10 0.25 ± 0 3° to 9° Document Number: 83675 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620A, SFH6206 www.vishay.com Vishay Semiconductors DIP-4, Option 6 10.16 typ. 5.10 max. 7.62 typ. 4.70 ± 0.15 6.60 ± 0.25 0.10 min. 3.55 ± 0.25 0.70 min. 1.27 ± 0.10 2.54 typ. Pin one I.D. 4 3 1 2 0.25 ± 0.10 3.05 ± 0.50 0.50 ± 0.10 10.55 ± 0.40 SMD-4, Option 7 10.30 max. 5.10 max. 7.62 typ. 4.70 ± 0.15 6.60 ± 0.25 1.27 ± 0.10 8.00 min. 0.50 min. Leads coplanarity 0.1 max. 2.54 typ. 3 .25 R0 1.78 2.54 0.76 4 4.30 ± 0.30 0.25 ± 0.10 0.50 min. 3.55 ± 0.25 0.70 min. 1.52 8.00 min. Pin one I.D. Rev. 2.3, 31-Aug-15 11.05 1 2 Document Number: 83675 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620A, SFH6206 www.vishay.com Vishay Semiconductors SMD-4, Option 9 10.05 max. 5.10 max. 7.62 typ. 4.70 ± 0.15 6.60 ± 0.25 3.55 ± 0.25 0.20 ± 0.10 0.25 ± 0.10 0.70 min. 1.27 ± 0.10 0.50 min. Leads coplanarity 0.1 max. 8.00 min. 2.54 typ. 4 0.76 3 2.54 .25 1.78 R0 1.52 8.00 min. Pin one I.D. 11.05 1 2 PACKAGE MARKING (example) YWW H 68 SFH620A-1 V X001 Notes • Only options 1 and 7 are reflected in the package marking. • The VDE logo is only marked on option1 parts. • Tape and reel suffix (T) is not part of the package marking. SOLDER PROFILES 300 300 5s Lead temperature ca. 2 K/s 2 K/s 50 full line: typical dotted line: process limits second wave Temperature (°C) Temperature (°C) 235 °C to 260 °C first wave 200 wave ca. 200 K/s 150 100 °C to 130 °C 100 200 max. 30 s 150 max. ramp down 6 °C/s 50 0 94 8626 50 100 max. ramp up 3 °C/s 0 150 200 250 Time (s) Fig. 9 - Wave Soldering Double Wave Profile According to J-STD-020 for DIP-8 Devices Rev. 2.3, 31-Aug-15 max. 100 s max. 120 s 100 ca. 5 K/s forced cooling 0 max. 260 °C 245 °C 255 °C 240 °C 217 °C 250 250 0 19841 50 100 150 200 250 300 Time (s) Fig. 10 - Lead (Pb)-free Reflow Solder Profile According to J-STD-020 for SMD-8 Devices Document Number: 83675 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620A, SFH6206 www.vishay.com Vishay Semiconductors HANDLING AND STORAGE CONDITIONS ESD level: HBM class 2 Floor life: unlimited Conditions: Tamb < 30 °C, RH < 85 % Moisture sensitivity level 1, according to J-STD-020 Rev. 2.3, 31-Aug-15 Document Number: 83675 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000