TMPG06-10 thru TMPG06-43A Datasheet

TMPG06-10 thru TMPG06-43A
www.vishay.com
Vishay General Semiconductor
PAR® Transient Voltage Suppressors
High Temperature Stability and High Reliability Conditions
FEATURES
• Available in uni-directional polarity only
• 400 W peak pulse power capability with
a 10/1000 μs waveform, repetitive rate
(duty cycle): 0.01 %
• Excellent clamping capability
• Very fast response time
MPG06
• Low incremental resistance
• Solder dip 275 °C max. 10 s, per JESD 22-B106
• AEC-Q101 qualified
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
PRIMARY CHARACTERISTICS
APPLICATIONS
VBR
10 V to 43 V
VWM
8.10 V to 36.8 V
PPPM
400 W
PD
1.0 W
IFSM
40 A
TJ max.
185 °C
Polarity
Uni-directional
Package
MPG06
Use in sensitive electronics protection against voltage
transients induced by inductive load switching and lighting
on ICs, MOSFET, signal lines of sensor units for consumer,
computer, industrial, automotive and telecommunication.
MECHANICAL DATA
Case: MPG06, molded epoxy over passivated junction
Molding compound meets UL 94 V-0 flammability rating
Base P/NHE3 - RoHS-compliant, AEC-Q101 qualified
Terminals: Matte tin plated leads, solderable
J-STD-002 and JESD 22-B102
HE3 suffix meets JESD 201 class 2 whisker test
per
Polarity: Color band denotes cathode end
MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)
PARAMETER
SYMBOL
VALUE
UNIT
Peak pulse power dissipation with a 10/1000 μs waveform (1) (fig. 1)
PPPM
400
W
Peak pulse current with a 10/1000 μs waveform (1)(2) (fig. 3)
IPPM
See next table
A
Power dissipation on infinite heatsink at TL = 75 °C (fig. 5)
PD
1.0
W
Peak forward surge current 8.3 ms single half sine-wave (2)
IFSM
40
A
VF
3.5
V
TJ, TSTG
-65 to +185
°C
Maximum instantaneous forward voltage at 25 A
(2)
Operating junction and storage temperature range
Notes
(1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 °C per fig. 2
A
(2) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum
Revision: 04-May-16
Document Number: 88404
1
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TMPG06-10 thru TMPG06-43A
www.vishay.com
Vishay General Semiconductor
ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
DEVICE TYPE
BREAKDOWN
VOLTAGE
VBR AT IT (1)
(V)
TEST
STAND-OFF
CURRENT VOLTAGE
IT
VWM
(V)
(mA)
MAXIMUM
REVERSE
REVERSE
LEAKAGE
LEAKAGE
AT VWM
AT VWM
TJ = 150 °C
ID
(μA)
(μA)
MAXIMUM
PEAK
PULSE
CURRENT
IPPM (2)
(A)
MAXIMUM
MAXIMUM
CLAMPING TEMPERATURE
VOLTAGE
COEFFICIENT
AT IPPM
OF VBR
VC (V)
(%/°C)
MIN.
MAX.
TMPG06-10
9.00
11.0
1.0
8.10
5.0
20.0
26.7
15.0
0.073
TMPG06-10A
9.50
10.5
1.0
8.55
5.0
20.0
27.6
14.5
0.073
TMPG06-11
9.90
12.1
1.0
8.92
2.0
10.0
24.7
16.2
0.075
TMPG06-11A
10.5
11.6
1.0
9.40
2.0
10.0
25.6
15.6
0.075
TMPG06-12
10.8
13.2
1.0
9.72
1.0
5.0
23.1
17.3
0.076
TMPG06-12A
11.4
12.6
1.0
10.2
1.0
5.0
24.0
16.7
0.078
TMPG06-13
11.7
14.3
1.0
10.5
1.0
5.0
21.1
19.0
0.081
TMPG06-13A
12.4
13.7
1.0
11.1
1.0
5.0
22.0
18.2
0.081
TMPG06-15
13.5
16.3
1.0
12.1
1.0
5.0
18.2
22.0
0.084
TMPG06-15A
14.3
15.8
1.0
12.8
1.0
5.0
18.9
21.2
0.084
TMPG06-16
14.4
17.6
1.0
12.9
1.0
5.0
17.0
23.5
0.086
TMPG06-16A
15.2
16.8
1.0
13.6
1.0
5.0
17.8
22.5
0.086
TMPG06-18
16.2
19.8
1.0
14.5
1.0
5.0
15.1
26.5
0.088
TMPG06-18A
17.1
18.9
1.0
15.3
1.0
5.0
15.9
25.5
0.088
TMPG06-20
18.0
22.0
1.0
16.2
1.0
5.0
13.7
29.1
0.090
TMPG06-20A
19.0
21.0
1.0
17.0
1.0
5.0
14.4
27.7
0.090
TMPG06-22
19.8
24.2
1.0
17.8
1.0
5.0
12.5
31.9
0.092
TMPG06-22A
20.9
23.1
1.0
18.8
1.0
5.0
13.1
30.6
0.092
TMPG06-24
21.6
26.4
1.0
19.4
1.0
5.0
11.5
34.2
0.094
TMPG06-24A
22.8
25.2
1.0
20.5
1.0
5.0
12.0
33.2
0.094
TMPG06-27
24.3
29.7
1.0
21.8
1.0
5.0
10.2
39.1
0.096
TMPG06-27A
25.7
28.4
1.0
23.1
1.0
5.0
10.7
37.5
0.096
TMPG06-30
27.0
33.0
1.0
24.3
1.0
5.0
9.2
43.5
0.097
TMPG06-30A
28.5
31.5
1.0
25.6
1.0
5.0
9.7
41.4
0.097
TMPG06-33
29.7
36.3
1.0
26.8
1.0
5.0
8.4
47.7
0.098
TMPG06-33A
31.4
34.7
1.0
28.2
1.0
5.0
8.8
45.7
0.098
TMPG06-36
32.4
39.6
1.0
29.1
1.0
5.0
7.7
52.0
0.099
TMPG06-36A
34.2
37.8
1.0
30.8
1.0
5.0
8.0
49.9
0.099
TMPG06-39
35.1
42.9
1.0
31.6
1.0
5.0
7.1
56.4
0.100
TMPG06-39A
37.1
41.0
1.0
33.3
1.0
5.0
7.4
53.9
0.100
TMPG06-43
38.7
47.3
1.0
34.8
1.0
5.0
6.5
61.9
0.101
TMPG06-43A
40.9
45.2
1.0
36.8
1.0
5.0
6.7
59.3
0.101
Notes
(1) Pulse test: t  50 ms
p
(2) Surge current waveform per fig. 3 and derated per fig. 2
(3) All terms and symbols are consistent with ANSI/IEEE CA62.35
ORDERING INFORMATION (Example)
PREFERRED PIN
TMPG06-10AHE3/54
(1)
UNIT WEIGHT (g)
PREFERRED PACKAGE CODE
BASE QUANTITY
DELIVERY MODE
0.218
54
5500
13" diameter paper tape and reel
Note
(1) AEC-Q101 qualified
Revision: 04-May-16
Document Number: 88404
2
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TMPG06-10 thru TMPG06-43A
www.vishay.com
Vishay General Semiconductor
RATINGS AND CHARCTERISTICS CURVES (TA = 25 °C unless otherwise noted)
10 000
Non-Repetitive Pulse
Waveform shown in Fig. 3
TA = 25 °C
CJ - Junction Capacitance (pF)
PPPM - Peak Oulse Power (kW)
100
10
TMPG06-10 - TMPG06-43A
1.0
Measured at
Zero Bias
1000
100
Measured at Stand-Off
Voltage VWM
10
1.0 µs
10 µs
100 µs
1.0 ms
10 ms
10
VBR - Breakdown Voltage (V)
Fig. 1 - Peak Pulse Power Rating Curve
Fig. 4 - Typical Junction Capacitance
100
1.00
75
50
25
60 Hz
Resistive or
Inductive Load
0.75
0.50
L = 0.375" (9.5 mm)
Lead Lengths
0.25
0
0
0
25
50
75
100
125
150
175
0
200
100
Half Value - IPP
IPPM
2
50
100
125
150
175
200
TJ = 75 °C
8.3 ms Single Half Sine-Wave
Peak Forward Surge Current (A)
Peak Value
IPPM
75
100
TJ = 25 °C
Pulse Width (td)
is defined as the Point
where the Peak Current
decays to 50 % of IPPM
tr = 10 µs
50
Fig. 5 - Power Derating Curve
Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature
150
25
TL - Lead Temperature (°C)
TJ - Initial Temperature (°C)
IPPM - Peak Pulse Current, % IRSM
100
td - Pulse Width (s)
PD - Power Dissipation (W)
Peak Pulse Power (PPP) or Current (IPP)
Derating in Percentage, %
0.1
0.1 µs
TJ = 25 °C
f = 1.0 MHz
Vsig = 50 mVp-p
10/1000 µs Waveform
as defined by R.E.A.
td
0
10
0
1.0
2.0
3.0
4.0
1
10
100
t - Time (ms)
Number of Cycles at 60 Hz
Fig. 3 - Pulse Waveform
Fig. 6 - Maximum Non-Repetitive Forward Surge Current
Revision: 04-May-16
Document Number: 88404
3
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TMPG06-10 thru TMPG06-43A
www.vishay.com
Vishay General Semiconductor
PACKAGE OUTLINE DIMENSIONS in inches (millimeters)
MPG06
0.100 (2.54)
0.090 (2.29)
DIA.
1.0 (25.4)
MIN.
0.125 (3.18)
0.115 (2.92)
1.0 (25.4)
MIN.
0.026 (0.66)
0.023 (0.584)
DIA.
Revision: 04-May-16
Document Number: 88404
4
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000