AA™900 Thermal Window - Architectural Detail Manual

AATM 900 IsoWebTM Window
EC 97911-056
INDEX
1
FIXED WINDOW................................................................................. 3-6
PROJECT-IN WINDOW.................................................................... 7-10
PROJECT-OUT WINDOW.............................................................. 11-14
INSWING CASEMENT WINDOW.................................................. 15-18
OUTSWING CASEMENT WINDOW.............................................. 19-23
MULLIONS..................................................................................... 25-29
RECEPTORS AND SUB SILLS..................................................... 30-31
ANCHORING...................................................................................... 31
MISCELLANEOUS DETAILS............................................................. 32
THERMAL CHARTS...................................................................... 33-42
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED
ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT
CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR
GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR.
Metric (SI) conversion figures are included throughout these details for reference.
Numbers in parentheses (
) are millimeters unless otherwise noted.
The following metric (SI) units are found in these details:
m –meter
cm – centimeter
mm –millimeter
s –second
Pa –pascal
MPa –megapascal
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MARCH, 2014
Kawneer reserves the right to change configurations without prior notice when deemed necessary
for product improvement.
kawneer.com
ADME040
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM 900 IsoWebTM Window
BLANK PAGE
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
MARH, 2014
EC 97911-056
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
FIXED WINDOW
Standard Features
Thermal Break
Exterior
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
• Heavy Commercial Grade Window
• Tested to US and Canadian Standards
• IsoWebTM Polyamide Thermal Break
• Tubular Profiles
• 45° Mitered Frame Corners
• Unique Mechanically Clipped or Staked Corner Joinery
• Factory Silicone Glazed or Field Dry Glazed
• Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
• Two Year Manufacturer’s Warranty
• Compatible with Storefront and Curtain Wall Systems
Fixed Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME040
Interior
3
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
Heavy Commercial Grade FW-HC90 / FW-AW90
OPTIONAL CLASS and GRADE
Heavy Commercial Grade FW-HC80 / FW-AW80
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-08 / A440-00
FRAME DEPTH
2-5/8" Overall Frame Depth
TYPICAL WALL THICKNESS
.070" Nominal Frame
TYPICAL MAX. SIZE
60" x 99"
TYPICAL MIN. SIZE
17" x 17"
TYPICAL CONFIGURATIONS
INFILL OPTIONS
1" Standard (Other Infill Options Available Upon Request)
STANDARD HARDWARE
Not Applicable
OPTIONAL HARDWARE
Not Applicable
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
SINGLE FIXED WINDOW
PERFORMANCE
US Standard
Canadian
Standard
Air
Infiltration
Water
Resistance
Design
Load
Thermal
Transmittance
AAMA 1503
Condensation
Resistance
AAMA 1503
CAN/CSA-A440
Sound
Transmittance
.10 Cfm/ft2
@ 6.24 psf
15 PSF
90 PSF
.34 "U" Value
67 CRF (Frame)
38 STC
0.25 (m3/h)/m
@ 300 Pa (Fixed)
720 Pa (B7)
4320 Pa (C5)
.34 "U" Value
60.9 I (Frame)
38 STC
Note:Thermal values are based upon 1" Low-E, Argon filled insulating glass.
STC value is based upon 1" laminated insulating glass.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
CLASS and GRADE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
FIXED WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
4
© Kawneer Company, Inc., 2014
2-5/8" (66)
3/8" (10)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3
3/8" (10)
kawneer.com
4
2
2-3/8" (60)
W.D.
D.L.O
D.L.O
ADME040
W.D.
O.D.
O.D.
3
JAMB
4
JAMB
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
2-3/8" (60)
D.L.O
2-3/8" (60)
W.D.
2
SILL
W.D.
1
HEAD
O.D.
1
O.D.
D.L.O
3/8" (10)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
FIXED WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
2-5/8" (66)
2-3/8" (60)
3/8" (10)
5
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM 900 IsoWebTM Window
BLANK PAGE
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
6
MARH, 2014
EC 97911-056
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
PROJECT-IN WINDOW
Standard Features
Thermal Break
Exterior
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
• Heavy Commercial Grade Window
• Tested to US and Canadian Standards
• IsoWebTM Polyamide Thermal Break
• Accentuated Tubular Profiles
• 45° Mitered Vent and Frame Corners
• Unique Mechanically Clipped or Staked Corner Joinery
• Factory Silicone Glazed or Field Dry Glazed
• Integral Air Seal
• Adjustable EURO-Groove Mounted Hardware
• Single Handle Multi-Point Locking
• Multiple Locking Handle Styles and Finishes
• Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
• Two Year Manufacturer’s Warranty
• Compatible with Storefront and Curtain Wall Systems
Project-in Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME040
Interior
7
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
Heavy Commercial Grade AP-HC90 / AP-AW90
OPTIONAL CLASS and GRADE
Heavy Commercial Grade FW-HC80 / FW-AW80
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-00
FRAME DEPTH
2-5/8" Overall Frame Depth
TYPICAL WALL THICKNESS
.070" Nominal Frame / .090" Nominal Vent
TYPICAL MAX. WINDOW SIZE
60" x 36" (72" x 48" with limitations - Consult Kawneer Engineering)
TYPICAL MIN. WINDOW SIZE
17" x 17"
TYPICAL CONFIGURATIONS
INFILL OPTIONS
1" Standard (Other Infill Options Available Upon Request)
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Single Handle Multi-Point Locking
OPTIONAL HARDWARE
Cast White Bronze Cam Handles
Access Control Locks
Pole and Pole Ring
Limit Stop
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
Insect Screens
SINGLE PROJECT-IN WINDOW
PERFORMANCE
US Standard
Canadian
Standard
Air
Infiltration
Water
Resistance
Design
Load
Thermal
Transmittance
AAMA 1503
Condensation
Resistance
AAMA 1503
CAN/CSA-A440
Sound
Transmittance
.10 Cfm/ft2
@ 6.24 psf
15 PSF
90 PSF
.43 "U" Value
64 CRF (Frame)
36 STC
0.55 (m3/h)/m
@300 Pa (A3)
720 Pa (B7)
3840 Pa (C5)
.43 "U" Value
50.2 I (Frame)
36 STC
Note:Thermal values are based upon 1" Low E, Argon filled insulating glass.
STC value is based upon 1" laminated insulating glass.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
CLASS and GRADE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PROJECT-IN WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
8
© Kawneer Company, Inc., 2014
2-5/8" (66)
3/8" (10)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
4-1/8" (105)
3/8" (10)
kawneer.com
D.L.O
D.L.O
D.L.O
1
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
D.L.O
W.D.
ADME040
2
SILL
O.D.
W.D.
O.D.
3
JAMB
4
JAMB
4-1/8" (105)
3
W.D.
4-1/8" (105)
W.D.
O.D.
1
HEAD
O.D.
3/8" (10)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
PROJECT-IN WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
2-5/8" (66)
4
4-1/8" (105)
3/8" (10)
9
AATM 900 IsoWebTM Window
EC 97911-056
A standard hinge for ventilators providing approximately 45° to 60°
openings depending on size. An optional limit stop is available to
restrict hinge travel and limit vent opening.
STANDARD
MULTI-POINT LOCKING
Single handle multi-point locking is standard providing any
number of concealed EURO-Groove mounted locking points
around the ventilator perimeter. Stylish handles are available
in black, white and silver painted finishes as well as chrome,
satin and polished brass.
CAM HANDLE
Cast white bronze cam handles are an alternative to standard
multi-point locking for the operation and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring provide manual
operation of ventilators located above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction with locking
hardware for sash pole operation of ventilators.
SASH POLE
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
A 3/4" diameter aluminum sash pole with a cast white bronze
pull down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional cast white
bronze Pole Hanger.
In lieu of cam handles and multi-point locking cast white
bronze access control locks are offered for managed control
of vent operations.
Lock is operated with a manganese bronze removable handle.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PROJECT-IN WINDOW
MARH, 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
10
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
PROJECT-OUT WINDOW
Standard Features
Thermal Break
Exterior
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
• Heavy Commercial Grade Window
• Tested to US and Canadian Standards
• IsoWebTM Polyamide Thermal Break
• Accentuated Tubular Profiles
• 45° Mitered Vent and Frame Corners
• Unique Mechanically Clipped or Staked Corner Joinery
• Factory Silicone Glazed or Field Dry Glazed
• Adjustable EURO-Groove Mounted Hardware
• Single Handle Multi-Point Locking
• Multiple Locking Handle Styles and Finishes
• Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
• Two Year Manufacturer’s Warranty
• Compatible with Storefront and Curtain Wall Systems
Project-out Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME040
Interior
11
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
Heavy Commercial Grade AC-HC90 / AP-AW90
OPTIONAL CLASS and GRADE
Heavy Commercial Grade AP-HC80 / AP-AW80
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-00
FRAME DEPTH
2-5/8" Overall Frame Depth
TYPICAL WALL THICKNESS
.070" Nominal Frame / .090" Nominal Vent
TYPICAL MAX. VENT SIZE
60" x 36" (72" x 48" with limitations - Consult Kawneer Engineering)
TYPICAL MIN. VENT SIZE
17" x 17"
TYPICAL CONFIGURATIONS
INFILL OPTIONS
1" Standard (Other Infill Options Available Upon Request)
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Single Handle Multi-Point Locking
OPTIONAL HARDWARE
Cast White Bronze Cam Handles
Access Control Locks
Pole and Pole Ring
Limit Stop
Pivot-Shoe Roto Operator
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
Insect Screens
UCS Powered Operators
SINGLE PROJECT-OUT WINDOW
PERFORMANCE
US Standard
Canadian
Standard
Air
Infiltration
Water
Resistance
Design
Load
Thermal
Transmittance
AAMA 1503
Condensation
Resistance
AAMA 1503
CAN/CSA-A440
Sound
Transmittance
.10 Cfm/ft2
@ 6.24 psf
15 PSF
90 PSF
.47 "U" Value
61 CRF (Frame)
36 STC
0.55 (m3/h)/m
@300 Pa (A3)
720 Pa (B7)
3840 Pa (C5)
.47 "U" Value
50.2 I (Frame)
36 STC
Note:Thermal values are based upon 1" Low E, Argon filled insulating glass.
STC value is based upon 1" laminated insulating glass.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
CLASS and GRADE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PROJECT-OUT WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
12
© Kawneer Company, Inc., 2014
2-5/8" (66)
3/8" (10)
3
3/8" (10)
kawneer.com
2
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
4-3/8" (111)
W.D.
D.L.O
D.L.O
W.D.
O.D.
O.D.
3
JAMB
4
JAMB
ADME040
D.L.O
4-3/8" (111)
W.D.
2
SILL
W.D.
O.D.
4
O.D.
D.L.O
3/8" (10)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1
1
HEAD
4-3/8" (111)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
PROJECT-OUT WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
2-5/8" (66)
4-3/8" (111)
3/8" (10)
13
AATM 900 IsoWebTM Window
EC 97911-056
A standard hinge for ventilators providing approximately 45° to 60°
openings depending on size. An optional limit stop is available to
restrict hinge travel and limit vent opening.
STANDARD
MULTI-POINT LOCKING
Single handle multi-point locking is standard providing any
number of concealed EURO-Groove mounted locking points
around the ventilator perimeter. Stylish handles are available
in black, white and silver painted finishes as well as chrome,
satin and polished brass.
CAM HANDLE
Cast white bronze cam handles are an alternative to standard
multi-point locking for the operation and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring provide manual
operation of ventilators located above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction with locking
hardware for sash pole operation of ventilators.
SASH POLE
A 3/4" diameter aluminum sash pole with a cast white bronze
pull down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional cast white
bronze Pole Hanger.
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
In lieu of cam handles and multi-point locking cast white
bronze access control locks are offered for managed control
of vent operations.
Lock is operated with a manganese bronze removable handle.
PIVOT-SHOE
ROTO-OPERATOR
Optional pivot shoe roto operator is located on the center line of
the bottom horizontal frame.
Standard finish shall be brushed copper nickel to match US-25-D.
MOTORIZED ACTUATORS
Chain operated motorized actuator. Suitable for bottom and top
hinged windows. Available in white, black or gray finish.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PROJECT-OUT WINDOW
MARH, 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
14
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
INSWING CASEMENT WINDOW
Standard Features
Thermal Break
Interior
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
• Heavy Commercial Grade Window
• Tested to US and Canadian Standards
• IsoWebTM Polyamide Thermal Break
• Accentuated Tubular Profiles
• 45° Mitered Vent and Frame Corners
• Unique Mechanically Clipped or Staked Corner Joinery
• Factory Silicone Glazed or Field Dry Glazed
• Integral Air Seal
• Adjustable EURO-Groove Mounted Hardware
• Single Handle Multi-Point Locking
• Multiple Locking Handle Styles and Finishes
• Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
• Two Year Manufacturer’s Warranty
• Compatible with Storefront and Curtain Wall Systems
HINGED
LEFT
Exterior
Inswing Casement Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME040
15
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
Heavy Commercial Grade C-HC90 / C-AW90
OPTIONAL CLASS and GRADE
Heavy Commercial Grade C-HC80 / C-AW80
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-00
FRAME DEPTH
2-5/8" Overall Frame Depth
TYPICAL WALL THICKNESS
.070" Nominal Frame / .090" Nominal Vent
TYPICAL MAX. WINDOW SIZE
36" x 60" (48" x 72" with limitations - Consult Kawneer Engineering)
TYPICAL MIN. WINDOW SIZE
17" x 17"
TYPICAL CONFIGURATIONS
INFILL OPTIONS
1" Standard (Other Infill Options Available Upon Request)
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Single Handle Multi-Point Locking
OPTIONAL HARDWARE
Cast White Bronze Cam Handles
Access Control Locks
Pole and Pole Ring
Limit Stop
Butt Hinges with Friction Adjusters
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
Insect Screens
SINGLE CASEMENT INSWING WINDOW
PERFORMANCE
US Standard
Canadian
Standard
Air
Infiltration
Water
Resistance
Design
Load
Thermal
Transmittance
AAMA 1503
Condensation
Resistance
AAMA 1503
CAN/CSA-A440
Sound
Transmittance
.10 Cfm/ft2
@ 6.24 psf
15 PSF
90 PSF
.43 "U" Value
64 CRF (Frame)
36 STC
0.5 (m3/h)/m
@300 Pa (A3)
720 Pa (B7)
3840 Pa (C5)
.43 "U" Value
50.2 I (Frame)
36 STC
Note:Thermal values are based upon 1" Low E, Argon filled insulating glass.
STC value is based upon 1" laminated insulating glass.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
CLASS and GRADE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
INSWING CASEMENT WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
16
© Kawneer Company, Inc., 2014
2-5/8" (66)
3/8" (10)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3/8" (10)
kawneer.com
D.L.O.
HINGED
LEFT
2
SILL
4-1/8" (105)
D.L.O.
D.L.O.
O.D.
W.D.
W.D.
O.D.
3
JAMB
4
JAMB
ADME040
D.L.O
2
4-1/8" (105)
W.D.
O.D.
1
4-1/8" (105)
3
W.D.
1
HEAD
O.D.
3/8" (10)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
INSWING CASEMENT WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
2-5/8" (66)
4
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
4-1/8" (105)
3/8" (10)
17
AATM 900 IsoWebTM Window
EC 97911-056
A standard hinge for ventilators providing up to 45° of open.
An optional limit stop is available to restrict hinge travel and
limit vent opening.
STANDARD
MULTI-POINT LOCKING
Single handle multi-point locking is standard providing any
number of concealed EURO-Groove mounted locking points
around the ventilator perimeter. Stylish handles are available
in black, white and silver painted finishes as well as chrome,
satin and polished brass.
CAM HANDLE
Cast white bronze cam handles are an alternative to standard
multi-point locking for the operation and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring provide manual
operation of ventilators located above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction with locking
hardware for sash pole operation of ventilators.
SASH POLE
A 3/4" diameter aluminum sash pole with a cast white bronze
pull down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional cast white
bronze Pole Hanger.
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
In lieu of cam handles and multi-point locking cast white
bronze access control locks are offered for managed control
of vent operations.
Lock is operated with a manganese bronze removable handle.
BUTT HINGE
An optional hinge available in anodized finishes or painted to
match window. Must be used with Friction Adjusters.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
INSWING CASEMENT WINDOW
MARH, 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
18
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
OUTSWING CASEMENT WINDOW
Standard Features
Interior
Exterior
HINGED
LEFT
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
• Heavy Commercial Grade Window
• Tested to US and Canadian Standards
• IsoWebTM Polyamide Thermal Break
• Accentuated Tubular Profiles
• 45° Mitered Vent and Frame Corners
• Unique Mechanically Clipped or Staked Corner Joinery
• Factory Silicone Glazed or Field Dry Glazed
• Adjustable EURO-Groove Mounted Hardware
• Single Handle Multi-Point Locking
• Multiple Locking Handle Styles and Finishes
• Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
• Two Year Manufacturer’s Warranty
• Compatible with Storefront and Curtain Wall Systems
Thermal Break
Outswing Casement Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME040
19
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
Heavy Commercial Grade C-HC90 / C-AW90
OPTIONAL CLASS and GRADE
Heavy Commercial Grade C-HC70 / C-AW70
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-00
FRAME DEPTH
2-5/8" Overall Frame Depth
TYPICAL WALL THICKNESS
.070" Nominal Frame / .090" Nominal Vent
TYPICAL MAX. WINDOW SIZE
36" x 60" (48" x 72" with limitations - (Consult Kawneer Engineering)
TYPICAL MIN. WINDOW SIZE
17" x 17"
TYPICAL CONFIGURATIONS
INFILL OPTIONS
1" Standard (Other Infill Options Available Upon Request)
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Single Handle Multi-Point Locking
OPTIONAL HARDWARE
Cast White Bronze Cam Handles
Access Control Locks
Pole and Pole Ring
Limit Stop
Butt Hinges
Roto Operator
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
Insect Screens
SINGLE CASEMENT OUTSWING WINDOW
PERFORMANCE
US Standard
Canadian
Standard
Air
Infiltration
Water
Resistance
Design
Load
Thermal
Transmittance
AAMA 1503
Condensation
Resistance
AAMA 1503
CAN/CSA-A440
Sound
Transmittance
.10 Cfm/ft2
@ 6.24 psf
15 PSF
90 PSF
.47 "U" Value
61 CRF (Frame)
36 STC
0.55 (m3/h)/m
@300 Pa (A3)
720 Pa (B7)
3360 Pa (C5)
.47 "U" Value
53.2 I (Frame)
36 STC
Note:Thermal values are based upon 1" Low E, Argon filled insulating glass.
STC value is based upon 1" laminated insulating glass.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
CLASS and GRADE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
OUTSWING CASEMENT WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
20
© Kawneer Company, Inc., 2014
2-5/8" (66)
3/8" (10)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3/8" (10)
kawneer.com
HINGED
LEFT
4-3/8" (111)
D.L.O.
4
W.D.
D.L.O.
W.D.
O.D.
O.D.
3
JAMB
4
JAMB
ADME040
D.L.O.
2
4-3/8" (111)
1
4-3/8" (111)
W.D.
2
SILL
W.D.
O.D.
D.L.O.
3
1
HEAD
O.D.
3/8" (10)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
OUTSWING CASEMENT WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
2-5/8" (66)
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
4-3/8" (111)
3/8" (10)
21
AATM 900 IsoWebTM Window
EC 97911-056
A standard hinge for ventilators providing up to 45° of open.
An optional limit stop is available to restrict hinge travel and
limit vent opening.
STANDARD
MULTI-POINT LOCKING
Single handle multi-point locking is standard providing any
number of concealed EURO-Groove mounted locking points
around the ventilator perimeter. Stylish handles are available
in black, white and silver painted finishes as well as chrome,
satin and polished brass.
MULTI-POINT LOCK
Optional single locking handle for concealed multi-point locks
located on the vertical frame. Standard finish shall be US-25-D
clear white bronze.
CAM HANDLE
Cast white bronze cam handles are an alternative to standard
multi-point locking for the operation and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring provide manual
operation of ventilators located above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction with locking
hardware for sash pole operation of ventilators.
SASH POLE
A 3/4" diameter aluminum sash pole with a cast white bronze
pull down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional cast white
bronze Pole Hanger.
HANGER
FOR SASH POLE
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
OUTSWING CASEMENT WINDOW
MARH, 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
22
AATM 900 IsoWebTM Window
EC 97911-056
OUTSWING CASEMENT WINDOW
23
ACCESS CONTROL
LOCK
In lieu of cam handles and multi-point locking cast white
bronze access control locks are offered for managed control
of vent operations.
Lock is operated with a manganese bronze removable handle.
BUTT HINGE
An optional hinge available in anodized finishes or painted to
match window. Must be used with Friction Adjusters.
ROTO-OPERATOR
Roto operators are used with butt hinges only and located at the
bottom horizontal frame. Standard finish shall be brushed copper
nickel to match US-25-D.
© Kawneer Company, Inc., 2014
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
MARCH, 2014
kawneer.com
ADME040
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM 900 IsoWebTM Window
BLANK PAGE
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
24
MARH, 2014
EC 97911-056
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
MULLIONS
WIND LOAD CHARTS:
25
THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design
wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in
allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MULLION CENTERS IN METERS
1.0
10
3.0
8
A
7
B
C
D
E
6
5
2.0
4
1.0
3
2
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
9
A = 40 PSF (1915)
B = 50 PSF (2394)
C = 60 PSF (2873)
D = 70 PSF (3352)
E = 90 PSF (4309)
248202
1
0
0
1
2
3
4
5
6
MULLION CENTERS IN FEET
MULLION CENTERS IN METERS
1.0
10
3.0
A
8
B
C
D
E
7
6
5
2.0
4
1.0
3
2
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
9
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
UNITS WITHOUT HORIZONTALS
1
0
0
1
2
3
4
5
6
MULLION CENTERS IN FEET
UNITS WITHOUT HORIZONTALS
kawneer.com
ADME040
A = 40 PSF (1915)
B = 50 PSF (2394)
C = 60 PSF (2873)
D = 70 PSF (3352)
E = 90 PSF (4309)
248203
26
AATM 900 IsoWebTM Window
MARH, 2014
MULLIONS
EC 97911-056
WIND LOAD CHARTS:
THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design
wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in
allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MULLION CENTERS IN METERS
1.0
10
3.0
8
7
A
2.0
B
C
D
E
6
5
4
1.0
3
2
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
9
A = 40 PSF (1915)
B = 50 PSF (2394)
C = 60 PSF (2873)
D = 70 PSF (3352)
E = 90 PSF (4309)
248207
248202
248207
1
0
0
1
2
3
4
5
6
MULLION CENTERS IN FEET
MULLION CENTERS IN METERS
1.0
10
3.0
8
7
A2.0
B
C
D
E
6
5
4
1.0
3
2
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
9
A = 40 PSF (1915)
B = 50 PSF (2394)
C = 60 PSF (2873)
D = 70 PSF (3352)
E = 90 PSF (4309)
248206
248202
248206
1
0
0
1
2
3
4
5
6
MULLION CENTERS IN FEET
UNITS WITHOUT HORIZONTALS
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
UNITS WITHOUT HORIZONTALS
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
MULLIONS
WIND LOAD CHARTS:
27
THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design
wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in
allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MULLION CENTERS IN METERS
1.0
10
B
C
D
8
7
2.0
E
6
5
4
1.0
3
2
MULLION HEIGHT IN METERS
9
MULLION HEIGHT IN FEET
3.0
A
A = 40 PSF (1915)
B = 50 PSF (2394)
C = 60 PSF (2873)
D = 70 PSF (3352)
E = 90 PSF (4309)
248200
248200
1
0
0
1
2
3
4
5
6
MULLION CENTERS IN FEET
MULLION CENTERS IN METERS
1.0
10
3.0
8
7
2.0
A
B
C
D
E
6
5
4
1.0
3
2
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
9
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
UNITS WITHOUT HORIZONTALS
1
0
0
1
2
3
4
5
6
MULLION CENTERS IN FEET
UNITS WITHOUT HORIZONTALS
kawneer.com
ADME040
A = 40 PSF (1915)
B = 50 PSF (2394)
C = 60 PSF (2873)
D = 70 PSF (3352)
E = 90 PSF (4309)
248200 248210 248200
28
AATM 900 IsoWebTM Window
MARH, 2014
MULLIONS
EC 97911-056
WIND LOAD CHARTS:
THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design
wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in
allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves.
1.0
B
C
D
MULLION HEIGHT IN FEET
9
8
E
7
2.0
6
5
4
1.0
3
A = 40 PSF (1915)
B = 50 PSF (2394)
C = 60 PSF (2873)
D = 70 PSF (3352)
E = 90 PSF (4309)
3.0
2
MULLION HEIGHT IN METERS
10
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MULLION CENTERS IN METERS
1
0
0
1
2
3
4
5
6
248200 248208 248200
MULLION CENTERS IN FEET
MULLION CENTERS IN METERS
1.0
10
3.0
8
7
2.0
A
B
C
D
E
6
5
4
1.0
3
2
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
9
A = 40 PSF (1915)
B = 50 PSF (2394)
C = 60 PSF (2873)
D = 70 PSF (3352)
E = 90 PSF (4309)
248200
248211
248200
1
0
0
1
2
3
4
5
6
MULLION CENTERS IN FEET
UNITS WITHOUT HORIZONTALS
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
UNITS WITHOUT HORIZONTALS
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
MULLIONS
WIND LOAD CHARTS:
29
THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design
wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in
allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MULLION CENTERS IN METERS
1.0
10
3.0
8
A
B
C2.0
D
E
7
6
5
4
1.0
3
2
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
9
1
0
0
1
2
3
4
5
248200
6
MULLION CENTERS IN FEET
© Kawneer Company, Inc., 2014
UNITS WITHOUT HORIZONTALS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
A = 40 PSF (1915)
B = 50 PSF (2394)
C = 60 PSF (2873)
D = 70 PSF (3352)
E = 90 PSF (4309)
kawneer.com
ADME040
248212
248200
RECEPTORS AND SUB SILLS
248018
248205
1-3/8"
(34.9)
2"
(50.8)
ADME040
248018
248205
1-3/8"
(34.9)
2"
(50.8)
248209
3-1/2"
(88.9)
kawneer.com
© Kawneer Company, Inc., 2014
AATM 900 IsoWebTM Window
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
3-13/32"
(86.5)
3-13/32"
(86.5)
248018
2"
(50.8)
1-3/8"
(34.9)
248205
3-13/32"
(86.5)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
5/8"
(15.9)
30
MARH, 2014
EC 97911-056
SCALE : 3" = 1'-0"
TYPICAL RECEPTOR SYSTEM
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
RECEPTORS AND SUB SILLS, ANCHORING
31
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
4-3/16"
(106.4)
248448
248448
1-3/8"
(34.9)
1-3/8"
(34.9)
248448
4-3/16"
(106.4)
4-3/16"
(106.4)
1-3/8"
(34.9)
248448
5/8"
(15.9)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
RECEPTOR SYSTEM WITH HEAVY DUTY SLIP-ON ANCHOR
4-3/16"
(106.3)
248021
248448
4-3/16"
(106.3)
2-11/32"
(59.5)
TYPICAL SILL EXTENSION
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
ANCHORS
Trim Cover
Trim Base
HEAVY DUTY
SLIP-ON ANCHOR
Note: Refer to the "Window Panning and Trims"
section for more typical trim details.
Vinyl Rigid
Vapor Barrier
248468
248493
kawneer.com
ADME040
VAPOR BARRIER
TOP HAT EXTENSION
TOP HAT EXTENSION
AND
VAPOR BARRIER
HEAD
HEAD
HEAD
SILL
SILL
SILL
CURTAIN WALL ADAPTERS
1/2"
(12.7)
1/2"
(12.7)
7500 WALL
1600 WALL
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
MISCELLANEOUS DETAILS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM 900 IsoWebTM Window
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
32
MARH, 2014
EC 97911-056
SCALE : 3" = 1'-0"
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
THERMAL CHARTS
33
Generic Project Specific U-factor Example Calculation
(Percent of Glass will vary on specific products depending on sitelines)
51-3/4"
(1315)
5'-0"
(1524)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
3'-0"
(915)
27-3/4"
(705)
Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F
Total Daylight Opening
= 27-3/4" • 51-3/4" = 9.97ft2
Total Projected Area
= 3'-0" • 5'-0" = 15 ft2
Percent of Glass
= (Total Daylight Opening ÷ Total Projected Area)100
= (9.97 ÷ 15)100 = 66%
System U-factor vs Percent of Glass Area
(5.00)
0.85
0.80
(4.50)
0.75
N
0.60
0.55
0.53
0.50
0.45
0.35
(2.50)
(2.00)
0.30
0.20
70
66%
65
60
55
Percent of Glass Area
Based on 66% glass and center of glass (COG) U-factor of 0.42
System U-factor is equal to 0.53 Btu/hr • ft2 • °F
kawneer.com
(3.00)
0.40
0.25
75
(3.50)
ADME040
50
(1.50)
W
m2 • °C
System U-factor
© Kawneer Company, Inc., 2014
(2.73)
(2.61)
(2.50)
(2.39)
(2.27)
(2.16)
(2.05)
(1.93)
(1.82)
(1.71)
(1.59)
(1.48)
(1.37)
(1.25)
(1.14)
(4.00)
0.65
Btu
hr • ft2 • °F
System U-factor
COG
U-factor
0.48
0.46
0.44
0.42
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0.70
E IGN
PL S
M E
A D
EX OR
F
T
O
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.90
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
THERMAL CHARTS
AATM 900 FIXED WINDOW
System U-factor vs Percent of Glass Area
0.90
(5.00)
0.85
0.80
(4.50)
0.75
0.70
(4.00)
0.60
0.55
COG
U-factor
0.50
(2.73)
(2.61)
(2.50)
(2.39)
(2.27)
(2.16)
(2.05)
(1.93)
(1.82)
(1.71)
(1.59)
(1.48)
(1.37)
(1.25)
(1.14)
(3.00)
0.45
(2.50)
0.40
0.35
(2.00)
0.25
(1.50)
0.20
95
90
85
80
75
70
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
0.30
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.48
0.46
0.44
0.42
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
(3.50)
W
m2 • °C
System U-factor
0.65
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
Btu
hr • ft2 • °F
System U-factor
34
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
THERMAL CHARTS
35
AATM 900 FIXED WINDOW
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
0.80
0.75
0.75
0.70
0.70
0.65
0.65
0.60
0.60
0.55
0.55
0.50
0.50
0.45
0.45
0.40
0.40
0.35
0.35
0.30
0.30
0.25
0.25
0.20
0.20
0.15
0.15
0.10
0.10
0.05
0.05
System SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
COG
SHGC
70
75
80
85
90
95
0.00
System Visible Transmittance (VT) vs Percent of Vision Area
0.80
COG
VT
0.75
0.75
0.70
0.70
0.65
0.65
0.60
0.60
0.55
0.55
0.45
0.45
0.40
0.40
0.35
0.35
0.30
0.30
0.25
0.25
0.20
0.20
0.15
0.15
0.10
0.10
0.05
0.05
Vision Area / Total Area (%)
kawneer.com
ADME040
70
75
80
85
90
95
0.00
System VT
0.50
0.50
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Vision Area / Total Area (%)
36
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
AATM 900 FIXED WINDOW
Thermal Transmittance1 (BTU/hr • ft 2 • °F)
Overall U-Factor 4
0.48
0.52
0.46
0.51
0.44
0.49
0.42
0.48
0.40
0.46
0.38
0.45
0.36
0.43
0.34
0.42
0.32
0.40
0.30
0.38
0.28
0.37
0.26
0.35
0.24
0.34
0.22
0.32
0.20
0.31
Glass SHGC 3
Overall Glass U-Factor 4
Glass VT 3
Overall VT 4
0.75
0.63
0.75
0.62
0.70
0.59
0.70
0.58
0.65
0.55
0.65
0.54
0.60
0.51
0.60
0.50
0.55
0.47
0.55
0.46
0.50
0.42
0.50
0.42
0.45
0.38
0.45
0.37
0.40
0.34
0.40
0.33
0.35
0.30
0.35
0.29
0.30
0.26
0.30
0.25
0.25
0.22
0.25
0.21
0.20
0.17
0.20
0.17
0.15
0.13
0.15
0.12
0.10
0.09
0.10
0.08
0.05
0.05
0.05
0.04
NOTE: For glass values that are not listed, linear interpolation is permitted.
1. U-Factors are determined in accordance with NFRC 100.
2. SHGC and VT values are determined in accordance with NFRC 200.
3. Glass properties are based on center of glass values and are obtained from your glass supplier.
4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of
1200mm wide by 1500mm high (47-1/4" by 59-1/16").
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
Visible Transmittance 2
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
SHGC Matrix 2
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Glass U-Factor 3
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
THERMAL CHARTS
37
AATM 900 CASEMENT/PROJECT-IN WINDOW
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
0.90
(5.00)
0.85
0.80
(4.50)
0.75
0.70
0.48
0.46
0.44
0.42
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0.60
0.55
(2.73)
(2.61)
(2.50)
(2.39)
(2.27)
(2.16)
(2.05)
(1.93)
(1.82)
(1.71)
(1.59)
(1.48)
(1.37)
(1.25)
(1.14)
0.50
0.45
0.35
(2.50)
(2.00)
0.30
0.20
95
90
85
80
75
70
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
(3.00)
0.40
0.25
kawneer.com
(3.50)
ADME040
(1.50)
W
m2 • °C
System U-factor
COG
U-factor
(4.00)
Btu
hr • ft2 • °F
System U-factor
0.65
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
THERMAL CHARTS
AATM 900 CASEMENT/PROJECT-IN WINDOW
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
0.80
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
0.75
0.70
COG
SHGC
0.65
0.60
0.75
0.70
0.65
0.60
0.50
0.45
0.40
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.35
0.30
System SHGC
0.55
0.55
0.25
0.20
0.15
0.10
0.05
0.05
70
Vision Area / Total Area (%)
75
80
85
90
95
0.00
0.80
0.75
0.70
COG
VT
0.65
0.75
0.70
0.65
0.60
0.55
0.55
0.50
0.45
0.40
0.50
0.35
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
System VT
0.60
0.30
0.25
0.20
0.15
0.10
0.05
70
75
80
85
90
0.00
Vision Area / Total Area (%)
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System Visible Transmittance (VT) vs Percent of Vision Area
95
38
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
AATM 900 CASEMENT/PROJECT-IN WINDOW
Thermal Transmittance1 (BTU/hr • ft 2 • °F)
Overall U-Factor 4
0.48
0.57
0.46
0.56
0.44
0.55
0.42
0.54
0.40
0.53
0.38
0.52
0.36
0.51
0.34
0.50
0.32
0.49
0.30
0.48
0.28
0.47
0.26
0.46
0.24
0.45
0.22
0.44
0.20
0.43
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Glass U-Factor 3
Visible Transmittance 2
Glass SHGC 3
Overall Glass U-Factor 4
Glass VT 3
Overall VT 4
0.75
0.43
0.75
0.41
0.70
0.41
0.70
0.38
0.65
0.38
0.65
0.36
0.60
0.35
0.60
0.33
0.55
0.33
0.55
0.30
0.50
0.30
0.50
0.27
0.45
0.27
0.45
0.25
0.40
0.24
0.40
0.22
0.35
0.22
0.35
0.19
0.30
0.19
0.30
0.16
0.25
0.16
0.25
0.14
0.20
0.13
0.20
0.11
0.15
0.11
0.15
0.08
0.10
0.08
0.10
0.05
0.05
0.05
0.05
0.03
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
SHGC Matrix 2
NOTE: For glass values that are not listed, linear interpolation is permitted.
1. U-Factors are determined in accordance with NFRC 100.
2. SHGC and VT values are determined in accordance with NFRC 200.
3. Glass properties are based on center of glass values and are obtained from your glass supplier.
4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of
1200mm wide by 1500mm high (47-1/4" by 59-1/16").
kawneer.com
ADME040
39
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
THERMAL CHARTS
AATM 900 CASEMENT/PROJECT-OUT WINDOW
System U-factor vs Percent of Glass Area
0.90
(5.00)
0.85
0.80
(4.50)
0.75
0.70
(4.00)
COG
U-factor
(2.73)
(2.61)
(2.50)
(2.39)
(2.27)
(2.16)
(2.05)
(1.93)
(1.82)
(1.71)
(1.59)
(1.48)
(1.37)
(1.25)
(1.14)
0.55
0.50
0.45
(3.50)
(3.00)
(2.50)
0.40
0.35
(2.00)
0.30
(1.50)
0.20
95
90
85
80
75
70
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
0.25
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.48
0.46
0.44
0.42
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0.60
W
m2 • °C
System U-factor
0.65
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
Btu
hr • ft2 • °F
System U-factor
40
MARCH, 2014
AATM 900 IsoWebTM Window
EC 97911-056
THERMAL CHARTS
41
AATM 900 CASEMENT/PROJECT-OUT WINDOW
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
0.80
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
0.75
0.70
COG
SHGC
0.65
0.60
0.75
0.70
0.65
0.60
0.50
0.45
0.55
0.40
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.35
0.30
System SHGC
0.55
0.25
0.20
0.15
0.10
0.05
0.05
70
75
80
85
90
95
0.00
System Visible Transmittance (VT) vs Percent of Vision Area
0.80
0.75
0.70
0.65
COG
VT
0.60
0.75
0.70
0.65
0.60
0.55
0.55
0.50
0.45
0.40
0.50
0.35
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0.30
0.25
0.20
0.15
0.10
0.05
Vision Area / Total Area (%)
kawneer.com
ADME040
70
75
80
85
90
95
0.00
System VT
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Vision Area / Total Area (%)
42
AATM 900 IsoWebTM Window
MARH, 2014
EC 97911-056
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
AATM 900 CASEMENT/PROJECT-OUT WINDOW
Thermal Transmittance1 (BTU/hr • ft 2 • °F)
Overall U-Factor 4
0.48
0.61
0.46
0.60
0.44
0.59
0.42
0.59
0.40
0.58
0.38
0.57
0.36
0.56
0.34
0.55
0.32
0.54
0.30
0.53
0.28
0.52
0.26
0.51
0.24
0.50
0.22
0.49
0.20
0.48
Glass SHGC 3
Overall Glass U-Factor 4
Glass VT 3
Overall VT 4
0.75
0.42
0.75
0.40
0.70
0.39
0.70
0.37
0.65
0.37
0.65
0.34
0.60
0.34
0.60
0.32
0.55
0.32
0.55
0.29
0.50
0.29
0.50
0.26
0.45
0.26
0.45
0.24
0.40
0.24
0.40
0.21
0.35
0.21
0.35
0.19
0.30
0.18
0.30
0.16
0.25
0.16
0.25
0.13
0.20
0.13
0.20
0.11
0.15
0.10
0.15
0.08
0.10
0.08
0.10
0.05
0.05
0.05
0.05
0.03
NOTE: For glass values that are not listed, linear interpolation is permitted.
1. U-Factors are determined in accordance with NFRC 100.
2. SHGC and VT values are determined in accordance with NFRC 200.
3. Glass properties are based on center of glass values and are obtained from your glass supplier.
4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of
1200mm wide by 1500mm high (47-1/4" by 59-1/16").
ADME040
kawneer.com
© Kawneer Company, Inc., 2014
Visible Transmittance 2
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
SHGC Matrix 2
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Glass U-Factor 3