VISHAY 1N4003GP

1N4001GP THRU 1N4007GP
GLASS PASSIVATED JUNCTION RECTIFIER
Reverse Voltage - 50 to 1000 Volts
FEATURES
D
*
DO-204AL
N
T
E
♦ Plastic package has
Underwriters
Laboratory Flammability
Classification 94V-0
♦ High temperature metallurgically
bonded construction
♦ Glass passivated cavity-free junction
♦ Capable of meeting environmental standards of
MIL-S-19500
♦ 1.0 Ampere operation at TA=75°C with no thermal
runaway
♦ Typical IR less than 0.1µA
♦ High temperature soldering guaranteed:
350°C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
1.0 (25.4)
MIN.
E
P
A
T
Forward Current - 1.0 Ampere
0.107 (2.7)
0.080 (2.0)
DIA.
0.205 (5.2)
0.160 (4.1)
1.0 (25.4)
MIN.
0.034 (0.86)
0.028 (0.71)
DIA.
NOTE: Lead diameter is 0.026 (0.66)
0.023 (0.58)
MECHANICAL DATA
for suffix "E" part numbers
Dimensions in inches and (millimeters)
*Glass-plastic encapsulation technique is covered by
Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306
®
Case: JEDEC DO-204AL molded plastic over glass body
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.012 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS
1N
1N
4001GP 4002GP
1N
4003GP
1N
4004GP
1N
1N
4005GP 4006GP
1N
4007GP UNITS
* Maximum repetitive peak reverse voltage
VRRM
50
100
200
400
600
800
1000
Volts
* Maximum RMS voltage
VRMS
35
70
140
280
420
560
700
Volts
* Maximum DC blocking voltage
VDC
50
100
200
400
600
800
1000
Volts
* Maximum average forward rectified current
0.375" (9.5mm) lead length at TA=75°C
I(AV)
1.0
Amp
* Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
IFSM
30.0
Amps
VF
1.1
Volts
IR(AV)
30.0
µA
IR
5.0
50.0
µA
Maximum instantaneous forward voltage at 1.0A
* Maximum full load reverse current, full cycle
average 0.375" (9.5mm) lead length TA= 75°C
* Maximum DC reverse current
at rated DC blocking voltage
TA=25°C
TA=125°C
Typical reverse recovery time (NOTE 1)
Typical junction capacitance (NOTE 2)
Typical thermal resistance (NOTE 3)
* Operating junction and storage temperature range
trr
2.0
µs
CJ
8.0
pF
RΘJA
RΘJL
55.0
25.0
°C/W
TJ, TSTG
-65 to +175
°C
NOTES:
(1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr= 0.25A
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted
*JEDEC registered values
4/98
RATINGS AND CHARACTERISTIC CURVES 1N4001GP THRU 1N4007GP
FIG. 1 - FORWARD CURRENT DERATING CURVE
60 HZ
RESISTIVE OR
INDUCTIVE LOAD
0.8
0.6
0.4
0.2
30
PEAK FORWARD SURGE CURRENT,
AMPERES
AVERAGE FORWARD RECTIFIED CURRENT,
AMPERES
1.0
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
0.375” (9.5mm) LEAD LENGTH
25
50
75
25
20
15
10
5.0
0
0
TJ=TJ max.
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
100
125
150
10
1
175
AMBIENT TEMPERATURE, °C
FIG. 3 - TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
INSTANTANEOUS FORWARD CURRENT, AMPERES
20
10
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
1
100
NUMBER OF CYCLES AT 60 HZ
0.1
10
TJ=100°C
1
0.1
TJ=25°C
0.01
0
20
60
40
80
100
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
0.01
0.6
0.8
1.0
1.2
1.4
1.6
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
TRANSIENT THERMAL IMPEDANCE (°C/W)
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE, pF
20
TJ=25°C
f=1.0 MHZ
Vsig=50mVp-p
10
1
0.1
100
10
1
0.1
0.01
0.1
1
t, PULSE DURATION, sec
1
10
REVERSE VOLTAGE, VOLTS
100
10
100