MPG06A THRU MPG06M MINIATURE GLASS PASSIVATED JUNCTION PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere FEATURES Case Style MPG06 0.100 (2.54) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Low forward voltage, high current capability ♦ Glass passivated chip junction ♦ High surge capability ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.090 (2.29) DIA 0.125 (3.18) 0.115 (2.92) MECHANICAL DATA 1.0 (25.4) MIN. Case: Molded plastic over passivated chip Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.0064 ounce, 0.181 gram 0.025 (0.635) 0.023 (0.584) DIA. Dimensions are in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS MPG 06A MPG 06B MPG 06D MPG 06G MPG 06J MPG 06K MPG 06M UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current 0.375" (9.5mm) lead length at TA=25°C I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 40.0 Amps VF 1.1 Volts Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C IR 5.0 50.0 µA Typical junction capacitance (NOTE 1) CJ 10.0 pF Typical reverse recovery time (NOTE 2) trr 0.6 µs RΘJA RΘJL 67.0 30.0 °C/W TJ, TSTG -55 to +150 °C Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (3) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length, P.C.B. mounted with 0.22 x 0.22” (5.5 x 5.5mm) copper pads 4/98 RATINGS AND CHARACTERISTIC CURVES MPG06A THRU MPG06M FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG. 1 - FORWARD CURRENT DERATING CURVE 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTH 1.0 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 1.2 0.8 0.6 0.4 CAPACITANCE LOADS 5.0 Ipk/IAV = 10 20 0.2 0 0 25 50 75 50 40 NO LOAD CONDITION 30 RATED LOAD 20 10 0 100 125 150 175 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 AMBIENT TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 100 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 30 TJ=150°C 1 10 NUMBER OF CYCLES AT 60 HZ TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 10 TJ=125°C 1 TJ=75°C 0.1 TJ=25°C 0.01 0 0.1 20 40 80 60 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS JUNCTION CAPACITANCE, pF 30 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 1 1 10 REVERSE VOLTAGE, VOLTS 100 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, °C/W FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 10 1 0.1 0.01 0.1 1 10 t, PULSE DURATION, sec. 100