February, 21st 2012 Automotive grade AUIPS7221R PWM INTELLIGENT POWER HIGH SIDE SWITCH Features Product Summary Integrated bootstrap for 100kHz switching Charge pump for DC operation Over temperature shutdown Over current shutdown 3.3V logic level Ground loss protection ESD protection Applications Rds(on) 35m max. Vbr 75V min. I shutdown 25A(min.) Package 24V loads Injectors Valves DC motors Description The Device is a five terminal Intelligent Power Switch (IPS) for use in a high side configuration. It features short circuit, over-temperature, ESD protection, inductive load capability and diagnostic feedback. An integrated bootstrap diode allows fast switching. D-Pak Typical Connection +Bat Vcc(3) 4k7 In(1) Control Cb(4) 4k7 Input Signal V Diag Bootstrap capacitor Gnd(2) Out(5) Load www.irf.com *Required, see absolute maximum ratings 1 AUIPS7221R Qualification Information† Automotive †† (per AEC-Q100 ) Comments: This family of ICs has passed an Automotive qualification. IR’s Industrial and Consumer qualification level is granted by extension of the higher Automotive level. Qualification Level Moisture Sensitivity Level DPAK-5L MSL1, 260°C (per IPC/JEDEC J-STD-020) Class M2 (150V) (per AEC-Q100-003) Class H1A (500V) ESD Human Body Model (per AEC-Q100-002) Class C4 (1000V) Charged Device Model (per AEC-Q100-011) Class II, Level A IC Latch-Up Test (per AEC-Q100-004) RoHS Compliant Yes † Qualification standards can be found at International Rectifier’s web site http://www.irf.com/ †† Exceptions to AEC-Q100 requirements are noted in the qualification report. Machine Model www.irf.com 2 AUIPS7221R Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. (Tj= -40°C..150°C, Vcc=6..60V unless otherwise specified). Symbol Parameter Vout Voffset Vin Vcc max. I in max. Maximum output voltage Maximum logic ground to load ground offset Maximum input voltage Maximum Vcc voltage Maximum input current Maximum power dissipation (internally limited by thermal protection) Rth=50°C/W 1”sqrt. footprint Max. storage & operating temperature junction temperature Pd Tj max. Min. Max. Units Gnd-3 Vcc+0.3 Vcc-65 Vcc+0.3 -0.3 5.5 65 -3 10 V mA W -40 2.5 150 °C Typ. Max. Units Thermal Characteristics Symbol Parameter Rth1 Rth2 Thermal resistance junction to ambient Thermal resistance junction to case 50 1.2 °C/W Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol Parameter VIH High level input voltage VIL Low level input voltage Rin Recommended resistor in series with IN pin Rdg Recommended resistor in series with dg pin F max. Max. switching frequency Cboot Bootstrap capacitor (1) limited by the maximum input current (2) limited by the input capacitor www.irf.com Min. Max. 2.7 0 2(1) 2(1) 5.5 0.9 10(2) 10(2) 100 50 30 Units V k kHz nF 3 AUIPS7221R Static Electrical Characteristics Tj=-40..150°C, Vcc=6..60V (unless otherwise specified) Symbol Parameter Rds(on) Icc Off Iout Off ON state resistance Tj=25°C ON state resistance Tj=150°C Operating voltage range with short circuit protection Supply current during Sleep mode Output leakage current during Sleep mode Icc On Iout Off Vcc op. Vih Vil In hyst. I in, on Vin, off Min. Typ. Max. 30 50 35 70 60 0.2 0.2 5 5 µA Supply current when On 4 10 mA Output current when Off during normal operation Input high threshold voltage Input low threshold voltage Input hysteresis Input current when the part is on Input voltage when the part is in fault mode 10 6 1 0.1 Units m Test Conditions Vin=5V, Iout=5A Vin=5V, Iout=5A V mA 1.9 1.6 0.3 15 0.1 2.2 0.5 30 0.4 µA V Typ. Max. Units During sleep mode Vin=0V, Vout=0V Tj=25°C, Vcc=28V Vin=5V Tj=25°C, Vcc=28V Vin=0V Tj=25°C, Vcc=28V V Vin=5V I in=5mA Switching Electrical Characteristics Vcc=28V, Resistive load=2 , Vin=5V, Tj=25°C Symbol Parameter tdon tr tdoff tf Turn-on delay time to 20% Rise time from 20% to 80% of Vcc Turn-off delay time to 80% Fall time from 80% to 20% of Vcc Min. 0.9 0.3 1.2 0.1 Test Conditions µs Protection Characteristics Tj=-40..150°C, Vcc=6..60V (unless otherwise specified) Symbol Isd Tsd UV H UV L Tdiag Tsleep Treset Parameter Over current shutdown Over temperature threshold Under voltage during turn on Under voltage during turn off Diagnostic time Time to enter in sleep mode Time to enter in sleep mode and reset the fault Twkp Time to leave the sleep mode Tpw on rst Power on reset duration (3) Guaranteed by design www.irf.com Min. Typ. Max. Units 25 150(3) 30 165 5 4 10 15 5 45 A °C 0.05 8 0.5 12 7 4 6 5 30 Test Conditions Vout=0V V ms µs see figure 1 see figure 2 see figure 1 Rin=4k7 see figure 2 & 3 4 AUIPS7221R Lead Assignments 3- Vcc 1- In 2- Gnd 3- Vcc 4- Cb 5- Out 12345 D Pak Functional Block Diagram All values are typical Vcc Cboot Under Voltage Bootstrap regulator 2V 1.5V 75V S Q Level Shifter 75V Driver R Sleep diag 6V Charge Pump Iout>30A Tj > 165°C 6V Gnd www.irf.com 350k IN OUT 5 AUIPS7221R Sleep_mode / Diagnostic Sleep_mode block manages the diagnostic and the sleep_mode. The device enters in sleep mode if input is inactive during a delay higher than Tsleep. IN out diag internal Tdiag Tsleep diag Tdiag Normal mode Fault mode Treset sleep mode Figure 1 Bootstrap The AUIPS7221 integrates a bootstrap regulator to maintain a fixed voltage on the bootstrap capacitor for any battery voltage. The regulator is off during the sleep mode to reduce the current consumption. Vcc 10mA Cboot 6V Out Load The 8mA current source flows permanently on the output when the output is off and the part is not in sleep mode. In case of an open load condition, the output voltage will be at Vcc-6V. Wake up sequence To wake up the part from the sleep mode, the input must be activated at least during Twkp, then the boostrap regulator is switched on and the boostrap capacitor is charged. The output will be not activated during Tpw on rst. www.irf.com 6 AUIPS7221R Tsleep IN Tpw on rst out Twkp sleep mode Normal mode sleep mode Figure 2 IN Tpw on rst out Twkp sleep mode Normal mode Figure 3 www.irf.com 7 AUIPS7221R 40 Isd, Over-current shutdown (A) Rds(on), Drain-to-Source On Resistance (Normalized) 200% 150% 100% 50% 30 20 10 0 -50 0 50 100 150 -50 Tj, junction temperature (°C) 50 10 0 15 0 Figure 6 – Isd (A) Vs Tj (°C) Figure 5 - Normalized Rds(on) (%) Vs Tj (°C) 0.5 2.0 On and Off delay time (µs) tr 0.4 Rising and falling time (µs) 0 Tj, junction temperature (°C) tf 0.3 0.2 0.1 0.0 1.5 1.0 tdon 0.5 tdoff 0.0 -50 0 50 100 150 Tj, junction temperature (°C) -50 0 50 100 150 Tj, junction temperature (°C) Figure 8 – tdon / tdoff (µs) Vs Tj (°C) Figure 7 – tr / tf (µs) Vs Tj (°C) www.irf.com 8 AUIPS7221R 5 Icc off, supply leakage current (µA) Zth, transient thermal impedance (°C/W) 10 0 10 1 0 .1 0 .0 1 1e - 5 1e - 4 1e - 3 1e - 2 1e - 1 1e + 0 1e + 1 1e + 2 1e + 3 Time (s) 4 3 2 1 0 -50 0 50 100 150 Tj, junction temperature (°C) Figure 9 – Transient thermal impedance (°C/W) Vs time (s) Figure 10 – Icc off (µA) Vs Tj (°C) Icc off, supply current (µA) 0.20 0.15 0.10 0.05 0.00 0 10 20 30 40 50 Vcc, supply voltage (V) Figure 11 – Icc off(A) Vs Vcc (V) www.irf.com 9 AUIPS7221R Case Outline 5 Lead – DPAK www.irf.com 10 AUIPS7221R Tape & Reel www.irf.com 5 Lead – DPAK 11 AUIPS7221R Part Marking Information Ordering Information Base Part Number Standard Pack Package Type Complete Part Number Form Tube AUIPS7221R www.irf.com D-Pak-5-Lead Quantity 75 AUIPS7221R Tape and reel 2000 AUIPS7221RTR Tape and reel left 3000 AUIPS7221RTRL Tape and reel right 3000 AUIPS7221RTRR 12 AUIPS7221R IMPORTANT NOTICE Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. Part numbers designated with the “AU” prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order acknowledgment. IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using IR components. To minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is not responsible or liable for any such statements. IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product. Only products certified as military grade by the Defense Logistics Agency (DLA) of the US Department of Defense, are designed and manufactured to meet DLA military specifications required by certain military, aerospace or other applications. Buyers acknowledge and agree that any use of IR products not certified by DLA as military-grade, in applications requiring military grade products, is solely at the Buyer’s own risk and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be responsible for any failure to meet such requirements. For technical support, please contact IR’s Technical Assistance Center http://www.irf.com/technical-info/ WORLD HEADQUARTERS: 101 N. Sepulveda Blvd., El Segundo, California 90245 Tel: (310) 252-7105 www.irf.com 13 AUIPS7221R Revision History Revision Date A March, 22nd 2010 B C D www.irf.com Notes/Changes nd July, 2 2010 st September, 1 2011 st February, 21 2012 Initial release Update ordering information Update typical schematic page 1 Update Iout off page 4 14