NVMFD5485NL Power MOSFET 60 V, 44 mW, 20 A, Dual N−Channel Features • • • • • • • Small Footprint (5x6 mm) for Compact Designs Low RDS(on) to Minimize Conduction Losses Low Capacitance to Minimize Driver Losses 175°C Operating Temperature NVMFD5485NLWF − Wettable Flank Option for Enhanced Optical Inspection AEC−Q101 Qualified and PPAP Capable This is a Pb−Free Device www.onsemi.com V(BR)DSS RDS(on) MAX ID MAX 44 m @ 10 V 60 V 20 A 60 m @ 4.5 V Dual N−Channel MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Symbol Value Unit Drain−to−Source Voltage VDSS 60 V Gate−to−Source Voltage VGS "20 V ID 19.5 A Parameter Continuous Drain Current RJC (Notes 1, 2, 4) TC = 25°C Power Dissipation RJC (Notes 1, 2) Continuous Drain Current RJA (Notes 1, 3 & 4) Steady State TC = 100°C TC = 25°C TA = 25°C Power Dissipation RJA (Notes 1 & 3) Pulsed Drain Current Steady State PD Operating Junction and Storage Temperature Source Current (Body Diode) Single Pulse Drain−to−Source Avalanche Energy (TJ = 25°C, VDD = 50 V, VGS = 10 V, IL(pk) = 25 A, L = 0.1 mH, RG = 25 ) Lead Temperature for Soldering Purposes (1/8″ from case for 10 s) MARKING DIAGRAM A 5.3 3.8 PD 2.9 IDM 113 A TJ, Tstg −55 to 175 °C IS 37 A EAS 31 mJ TL 260 °C TA = 100°C TA = 25°C, tp = 10 s W 19.2 ID W Symbol Value Unit Junction−to−Case − Steady State (Note 2) RJC 3.9 °C/W Junction−to−Ambient − Steady State (Note 3) RJA 52 1. The entire application environment impacts the thermal resistance values shown, they are not constants and are only valid for the particular conditions noted. 2. Surface−mounted to an ideal (infinite) heat sink. 3. Surface−mounted on FR4 board using a 650 mm2, 2 oz. Cu pad. 4. Maximum current for pulses as long as 1 second are higher but are dependent on pulse duration and duty cycle. May, 2015 − Rev. 3 DFN8 5x6 (SO8FL) CASE 506BT S1 G1 S2 G2 XXXXXX AYWZZ D1 D1 D2 D2 D2 D2 THERMAL RESISTANCE MAXIMUM RATINGS (Note 1) © Semiconductor Components Industries, LLC, 2015 D1 D1 1 1.4 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Parameter S2 S1 38.5 TA = 100°C TA = 25°C G2 G1 13.8 TC = 100°C D2 D1 1 XXXXXX = 5485NL XXXXXX = (NVMFD5485NL) or XXXXXX = 5485LW XXXXXX = (NVMFD5485NLWF) A = Assembly Location Y = Year W = Work Week ZZ = Lot Traceability ORDERING INFORMATION Device Package Shipping† NVMFD5485NLT1G DFN8 1500/ (Pb−Free) Tape & Reel NVMFD5485NLT3G DFN8 5000/ (Pb−Free) Tape & Reel NVMFD5485NLWFT1G DFN8 1500/ (Pb−Free) Tape & Reel NVMFD5485NLWFT3G DFN8 5000/ (Pb−Free) Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. Publication Order Number: NVMFD5485NL/D NVMFD5485NL ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise specified) Parameter Symbol Test Condition Min Drain−to−Source Breakdown Voltage V(BR)DSS VGS = 0 V, ID = 250 A 60 Drain−to−Source Breakdown Voltage Temperature Coefficient V(BR)DSS/TJ Reference to 25°C ID = 250 A Typ Max Unit OFF CHARACTERISTICS V 67 TJ = 25°C mV/°C 1.0 Zero Gate Voltage Drain Current IDSS Gate−to−Source Leakage Current IGSS VDS = 0 V, VGS = ±20 V VGS(TH) VGS = VDS, ID = 250 A VGS(TH)/TJ Reference to 25°C ID = 250 A −4.86 RDS(on) VGS = 10 V, ID = 15 A 33 44 VGS = 4.5 V, ID = 10 A 42 60 VGS = 0 V, VDS = 60 V TJ = 125°C A 10 ±100 nA 2.5 V ON CHARACTERISTICS (Note 5) Gate Threshold Voltage Threshold Temperature Coefficient Drain−to−Source On Resistance 1.5 mV/°C m CHARGES AND CAPACITANCES Input Capacitance Ciss Output Capacitance Coss Reverse Transfer Capacitance 560 VGS = 0 V, f = 1.0 MHz, VDS = 25 V Crss pF 126 58 Total Gate Charge QG(TOT) 20 Threshold Gate Charge QG(TH) Gate−to−Source Charge QGS VGS = 10 V, VDS = 48 V, ID = 10 A 0.52 Gate−to−Drain Charge QGD VGS = 4.5 V, VDS = 48 V, ID = 10 A 11.5 nC td(on) 9.5 ns tr VGS = 4.5 V, VDS = 48 V, ID = 10 A, RG = 2.5 26.6 Total Gate Charge QG(TOT) nC 1.9 7.9 SWITCHING CHARACTERISTICS (Note 6) Turn−On Delay Time Rise Time Turn−Off Delay Time Fall Time td(off) tf 27.8 23.7 DRAIN−SOURCE DIODE CHARACTERISTICS TJ = 25°C 0.93 TJ = 125°C 0.83 Forward Diode Voltage VSD Reverse Recovery Time tRR 28.9 Charge Time ta 23.2 Discharge Time tb Reverse Recovery Charge VGS = 0 V, IS = 15 A VGS = 0 V, dIS/dt = 100 A/s, IS = 10 A 1.2 V ns 5.6 QRR 35.5 nC LS 0.93 nH PACKAGE PARASITIC VALUES Source Inductance Drain Inductance LD Gate Inductance LG Gate Resistance RG TA = 25°C 0.005 1.84 12 5. Pulse Test: pulse width = 300 s, duty cycle v 2%. 6. Switching characteristics are independent of operating junction temperatures. www.onsemi.com 2 NVMFD5485NL TYPICAL CHARACTERISTICS 30 VGS = 10 to 6.5 V 5.5 V 25 VDS = 10 V 4.5 V ID, DRAIN CURRENT (A) ID, DRAIN CURRENT (A) 30 4.1 V 20 3.9 V 15 3.7 V 3.5 V 10 3.3 V 3.1 V 2.9 V 5 2.7 V 10 TJ = 25°C TJ = 125°C 1 2 3 4 1 5 TJ = −55°C 3 4 5 Figure 1. On−Region Characteristics Figure 2. Transfer Characteristics RDS(on), DRAIN−TO−SOURCE RESISTANCE (m) VGS, GATE−TO−SOURCE VOLTAGE (V) 0.08 ID = 10 A TJ = 25°C 0.07 0.06 0.05 0.04 0.03 0.02 2 2 VDS, DRAIN−TO−SOURCE VOLTAGE (V) 3 4 5 6 7 8 9 10 0.07 0.06 TJ = 25°C VGS = 4.5 V 0.05 0.04 VGS = 10 V 0.03 0.02 0.01 0 2 6 10 14 18 22 30 26 VGS, GATE−TO−SOURCE VOLTAGE (V) ID, DRAIN CURRENT (A) Figure 3. On−Resistance vs. VGS Figure 4. On−Resistance vs. Drain Current and Gate Voltage 1.0E−04 ID = 10 A VGS = 10 V 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 −50 −25 TJ = 150°C 1.0E−05 IDSS, LEAKAGE (A) RDS(on), DRAIN−TO−SOURCE RESISTANCE (m) 15 0 0 RDS(on), DRAIN−TO−SOURCE RESISTANCE (NORMALIZED) 20 5 0 2.4 2.2 2.0 25 1.0E−06 TJ = 125°C 1.0E−07 1.0E−08 1.0E−09 1.0E−10 TJ = 25°C 1.0E−11 1.0E−12 0 25 50 75 100 125 150 5 175 10 15 20 25 30 35 40 45 50 55 60 TJ, JUNCTION TEMPERATURE (°C) VDS, DRAIN−TO−SOURCE VOLTAGE (V) Figure 5. On−Resistance Variation with Temperature Figure 6. Drain−to−Source Leakage Current vs. Voltage www.onsemi.com 3 NVMFD5485NL TYPICAL CHARACTERISTICS TJ = 25°C VGS = 0 V 900 C, CAPACITANCE (pF) VGS, GATE−TO−SOURCE VOLTAGE (V) 1000 800 700 Ciss 600 500 400 300 Coss 200 Crss 100 0 0 10 20 30 40 50 60 QT 10 8 TJ = 25°C 6 Qgs 4 Qgd VDD = 48 V ID = 10 A 2 0 0 2 4 6 8 10 12 14 16 18 VDS, DRAIN−TO−SOURCE VOLTAGE (V) Qg, TOTAL GATE CHARGE (nC) Figure 7. Capacitance Variation Figure 8. Gate−to−Source and Drain−to−Source Voltage vs. Total Charge 20 10 1000 VDD = 48 V VGS = 4.5 V ID = 10 A IS, SOURCE CURRENT (A) 9 100 td(off) tr tf 10 td(on) TJ = 25°C VGS = 0 V 8 7 6 5 4 3 2 1 0 1 1 10 0 100 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 RG, GATE RESISTANCE () VSD, SOURCE−TO−DRAIN VOLTAGE (V) Figure 9. Resistive Switching Time Variation vs. Gate Resistance Figure 10. Diode Forward Voltage vs. Current 1000 ID, DRAIN CURRENT (A) t, TIME (ns) 12 100 TC = 25°C VGS = 10 V Single Pulse 10 s 100 s 1 ms 10 ms 10 dc 1 RDS(on) Limit Thermal Limit Package Limit 0.1 0.01 0.1 1 10 VDS, DRAIN−TO−SOURCE VOLTAGE (V) Figure 11. Maximum Rated Forward Biased Safe Operating Area www.onsemi.com 4 100 NVMFD5485NL TYPICAL CHARACTERISTICS 100 50% Duty Cycle R(t) (°C/W) 10 1 20% 10% 5% 2% 1% 0.1 Single Pulse 0.01 0.001 0.000001 0.00001 0.0001 0.001 0.01 0.1 PULSE TIME (sec) Figure 12. Thermal Response www.onsemi.com 5 1 10 100 1000 NVMFD5485NL PACKAGE DIMENSIONS DFN8 5x6, 1.27P Dual Flag (SO8FL−Dual) CASE 506BT ISSUE E 2X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 MM FROM THE TERMINAL TIP. 4. PROFILE TOLERANCE APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 6. SEATING PLANE IS DEFINED BY THE TERMINALS. A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE TO THE LOWEST POINT ON THE PACKAGE BODY. 7. A VISUAL INDICATOR FOR PIN 1 MUST BE LOCATED IN THIS AREA. 0.20 C D A B D1 8 7 6 ÉÉ ÉÉ ÉÉ PIN ONE IDENTIFIER NOTE 7 1 2 2X 0.20 C 5 E1 E 4X h c 3 A1 4 TOP VIEW DETAIL B 0.10 C DETAIL A A SOLDERING FOOTPRINT* 0.10 C NOTE 4 ALTERNATE CONSTRUCTION C SIDE VIEW DETAIL A SEATING PLANE NOTE 6 4.56 2X 8X D2 D3 4X e 1 2X 2.08 0.75 0.56 L K 4 4X 4.84 DETAIL B 1.40 2.30 M b1 MILLIMETERS MAX MIN MAX −−− 0.90 1.10 −−− −−− 0.05 0.33 0.42 0.51 0.33 0.42 0.51 0.20 −−− 0.33 5.15 BSC 4.70 4.90 5.10 3.90 4.10 4.30 1.50 1.70 1.90 6.15 BSC 5.70 5.90 6.10 3.90 4.15 4.40 1.27 BSC 0.45 0.55 0.65 −−− −−− 12 _ 0.51 −−− −−− 0.56 −−− −−− 0.48 0.61 0.71 3.25 3.50 3.75 1.80 2.00 2.20 6.59 3.70 4X N DIM A A1 b b1 c D D1 D2 D3 E E1 E2 e G h K K1 L M N E2 0.70 4X G 8 5 8X K1 BOTTOM VIEW b 0.10 C A B 0.05 C 4X 1.27 PITCH 5.55 1.00 NOTE 3 DIMENSION: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NVMFD5485NL/D