TC1413/TC1413N 3A High-Speed MOSFET Drivers Features General Description • Latch-Up Protected: Withstands 500 mA Reverse Current • Input Withstands Negative Inputs Up to 5V • Electrostatic Discharge (ESD) Protected: 2.0 kV (HBM) and 400V (MM) • High Peak Output Current: 3A • Wide Input Supply Voltage Operating Range: - 4.5V to 16V • High Capacitive Load Drive Capability: - 1800 pF in 20 ns • Short Delay Time: 35 ns typical • Matched Delay Times • Low Supply Current - With Logic ‘1’ Input: 500 µA - With Logic ‘0’ Input: 100 µA • Low Output Impedance: 2.7 • Available in Space-Saving 8-pin MSOP Package • Pinout - same as TC1410/TC1411/TC1412 The TC1413/TC1413N are 3A CMOS buffers/drivers. They do not latch up under any conditions within their power and voltage ratings. They are not subject to damage when up to 5V of noise spiking of either polarity occurs on the ground pin. They can accept, without damage or logic upset, up to 500 mA of current of either polarity being forced back into their output. All terminals are fully protected against electrostatic discharge (ESD) up to 2.0 kV (HBM) and 400V (MM). Applications • • • • Switch Mode Power Supplies Line Drivers Pulse Transformer Drive Relay Driver As MOSFET drivers, the TC1413/TC1413N can easily charge a 1800 pF gate capacitance in 20 ns with matched rise and fall times. To ensure the MOSFET’s intended state will not be affected even by large transients, low enough impedance in both the ‘On’ and ‘Off’ states are provided. The leading and trailing edge propagation delay times are also matched to allow driving short-duration inputs with greater accuracy. Package Type 8-Pin MSOP/PDIP/SOIC VDD 1 8 VDD VDD 1 IN 2 7 OUT IN 2 6 OUT NC 3 5 GND GND 4 TC1413 NC 3 GND 4 2 6,7 Inverting 8 VDD TC1413N 7 OUT 6 OUT 5 GND 2 6,7 Non-Inverting NC = No Internal Connection Note: 2001-2015 Microchip Technology Inc. For proper operation, duplicate pins must be connected together. DS20001392E-page 1 TC1413/TC1413N Functional Block Diagram TC1413 VDD Inverting Outputs 300 mV Output Non-Inverting Outputs Input Effective Input C = 10 pF 4.7V TC1413N GND DS20001392E-page 2 2001-2015 Microchip Technology Inc. TC1413/TC1413N 1.0 ELECTRICAL CHARACTERISTICS † Notice: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings† Supply Voltage ..................................................... +20V Input Voltage ...................... VDD + 0.3V to GND – 5.0V Power Dissipation (TA 70°C) MSOP .......................................................... 340 mW PDIP ............................................................ 730 mW SOIC............................................................ 470 mW Storage Temperature Range.............. -65°C to +150°C Maximum Junction Temperature ...................... +150ºC DC ELECTRICAL CHARACTERISTICS Electrical Specifications: Unless otherwise noted, TA = +25°C, with 4.5V VDD 16V. Parameters Sym. Min. Typ. Max. Units Logic ‘1’, High Input Voltage VIH 2.0 — — V Logic ‘0’, Low Input Voltage VIL — — 0.8 V Input Current IIN -1.0 — 1.0 µA -10 — 10 Conditions Input 0V VIN VDD, TA = +25°C -40°C TA +85°C Output High Output Voltage VOH VDD – 0.025 — — V DC Test Low Output Voltage VOL — — 0.025 V DC Test Output Resistance RO — 2.7 4.0 VDD = 16V, IO = 10 mA, TA = +25°C — 3.3 5.0 0°C TA +70°C -40°C TA +85°C — 3.3 5.0 Peak Output Current IPK — 3.0 — A VDD = 16V Latch-Up Protection Withstand Reverse Current IREV — 0.5 — A Duty cycle 2%, t 300 µs, VDD = 16V tR — 20 28 ns TA = +25°C — 22 33 — 24 33 — 20 28 — 22 33 — 24 33 — 35 45 — 40 50 — 40 50 — 35 45 — 40 50 0°C TA +70°C — 40 50 -40°C TA +85°C, Figure 4-1 — 0.5 1.0 — 0.1 0.15 Switching Time (Note 1) Rise Time Fall Time tF Delay Time Delay Time tD1 tD2 0°C TA +70°C -40°C TA +85°C, Figure 4-1 ns TA = +25°C 0°C TA +70°C -40°C TA +85°C, Figure 4-1 ns TA = +25°C, 0°C TA +70°C -40°C TA +85°C, Figure 4-1 ns TA = +25°C Power Supply Power Supply Current Note 1: IS mA VIN = 3V, VDD = 16V VIN = 0V Switching times ensured by design. 2001-2015 Microchip Technology Inc. DS20001392E-page 3 TC1413/TC1413N TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise noted, all parameters apply with 4.5V VDD 18V. Parameters Sym. Min. Typ. Max. Units Conditions Temperature Ranges Specified Temperature Range (C) TA 0 — +70 ºC Specified Temperature Range (E) TA -40 — +85 ºC Maximum Junction Temperature TJ — — +150 ºC Storage Temperature Range TA -65 — +150 ºC Thermal Resistance, 8L-MSOP JA — 211 — ºC/W Thermal Resistance, 8L-PDIP JA — 89.3 — ºC/W Thermal Resistance, 8L-SOIC JA — 149.5 — ºC/W Package Thermal Resistances DS20001392E-page 4 2001-2015 Microchip Technology Inc. TC1413/TC1413N 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Unless otherwise indicated, over operating temperature range with 4.5V VDD 16V. 500 500 TA = +25°C VSUPPLY = 16V VIN = 3V 400 VIN = 3V ISUPPLY (µA) ISUPPLY (µA) 400 300 200 100 0 300 200 100 VIN = 0V 0 4 6 8 10 12 14 16 VIN = 0V -40 -20 0 VDD (V) FIGURE 2-1: Quiescent Supply Current vs. Supply Voltage. FIGURE 2-4: vs. Temperature. 1.6 1.6 TA = +25°C 40 60 80 Quiescent Supply Current VSUPPLY = 16V 1.5 VIH VTHRESHOLD (V) VTHRESHOLD (V) 1.5 1.4 1.3 1.2 4 6 VIH 1.4 1.3 VIL 1.2 VIL 1.1 8 10 12 14 16 1.1 -40 -20 0 FIGURE 2-2: Voltage. Input Threshold vs. Supply FIGURE 2-5: Temperature. 9 9 8 8 7 7 RDS-ON (Ohms) TA = +85°C 6 TA = +25°C 5 20 40 60 80 TEMPERATURE (°C) VDD (V) RDS-ON (Ohms) 20 TEMPERATURE (°C) 4 3 Input Threshold vs. TA = +85°C 6 5 TA = +25°C 4 3 TA = -40°C 2 2 TA = -40°C 1 1 4 6 8 10 VDD (V) 12 14 FIGURE 2-3: High State Output Resistance vs. Supply Voltage. 2001-2015 Microchip Technology Inc. 16 4 6 8 10 VDD (V) 12 14 16 FIGURE 2-6: Low State Output Resistance vs. Supply Voltage. DS20001392E-page 5 TC1413/TC1413N Note: Unless otherwise indicated, over operating temperature range with 4.5V VDD 16V. 70 70 CLOAD = 1800 pF CLOAD = 1800 pF 60 50 TA = +85°C 40 TA = +25°C 30 20 10 tFALL (nsec) tRISE (nsec) 60 6 40 TA = +85°C TA = +25°C 30 20 TA = -40°C 4 50 TA = -40°C 8 10 12 14 10 16 4 6 8 10 VDD (V) FIGURE 2-7: Voltage. Rise Time vs. Supply FIGURE 2-10: Voltage. 16 Fall Time vs. Supply CLOAD = 1800 pF CLOAD = 1800 pF 100 90 90 80 tD2 (nsec) TA = +85°C 80 tD1 (nsec) 14 100 110 70 TA = +25°C 60 50 TA = +85°C 70 60 TA = +25°C 50 40 40 TA = -40°C 30 30 TA = -40°C 20 20 4 6 FIGURE 2-8: Supply Voltage. 8 10 VDD (V) 12 14 16 4 6 8 10 12 14 16 VDD (V) Propagation Delay vs. FIGURE 2-11: Supply Voltage. 40 Propagation Delay vs. 35 TA = +25°C VDD = 16V tFALL 20 10 0 Propagation Delays (nsec) tRISE 30 tRISE, tFALL (nsec) 12 VDD (V) TA = +25°C VDD = 16V 34 tD2 33 tD1 32 31 30 29 28 0 1000 2000 3000 4000 5000 0 1000 FIGURE 2-9: Capacitive Load. DS20001392E-page 6 Rise and Fall Times vs. 2000 3000 4000 5000 CLOAD (pF) CLOAD (pF) FIGURE 2-12: Capacitive Load. Propagation Delays vs. 2001-2015 Microchip Technology Inc. TC1413/TC1413N 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3-1. . TABLE 3-1: PIN FUNCTION TABLE Pin No. TC1413 MSOP, PDIP, SOIC TC1413N MSOP, PDIP, SOIC 1 VDD VDD 2 IN IN Control input No connection 3.1 Supply input, 4.5V to 16V 3 NC NC 4 GND GND Ground 5 GND GND Ground 6 OUT OUT CMOS push-pull output, common to pin 7 7 OUT OUT CMOS push-pull output, common to pin 6 8 VDD VDD Supply input, 4.5V to 16V Supply Input (VDD) The VDD input is the bias supply for the MOSFET driver and is rated for 4.5V to 16V with respect to the ground pin. The VDD input should be bypassed to ground with a local ceramic capacitor. The value of the capacitor is chosen based on the capacitive load that is being driven. A value of 1.0 µF is suggested. 3.2 Description Control Input (IN) The MOSFET driver input is a high-impedance, TTL/CMOS-compatible input. The input has 300 mV of hysteresis between the high and low thresholds which prevents output glitching even when the rise and fall time of the input signal is very slow. 3.3 CMOS Push-Pull Output (OUT, OUT) The MOSFET driver output is a low-impedance, CMOS push-pull style output, capable of driving a capacitive load with 3A peak currents. 3.4 Ground (GND) The ground pins are the return path for the bias current and for the high peak currents that discharge the load capacitor. The ground pins should be tied into a ground plane or have very short traces to the bias supply source return. 3.5 No Connect (NC) No internal connection. 2001-2015 Microchip Technology Inc. DS20001392E-page 7 TC1413/TC1413N 4.0 APPLICATION INFORMATION +5V 90% Input VDD = 16V 0V 1.0 µF 0.1 µF 1, 8 Input 10% tD1 tD2 tF VDD tR 90% 90% Output 2 6, 7 Output 10% 10% 0V CL = 1800 pF Inverting Driver TC1413 TC1413 TC1413N +5V 90% Input 4, 5 Input: 100 kHz, square wave, tRISE = tFALL 10 ns 0V VDD 10% tD1 90% tR Output 0V 10% 90% tD2 tF 10% Non-Inverting Driver TC1413N FIGURE 4-1: DS20001392E-page 8 Switching Time Test Circuit. 2001-2015 Microchip Technology Inc. TC1413/TC1413N 5.0 PACKAGING INFORMATION 5.1 Package Marking Information 8-Lead PDIP (300 mil) XXXXXXXX XXXXXNNN YYWW Example TC1413 e3 256 CPA^^ 1318 OR TC1413 CPA256 1318 Legend: XX...X Y YY WW NNN e3 * Note: Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code RoHS Compliant JEDEC® designator for Matte Tin (Sn) This package is RoHS Compliant. The RoHS Compliant JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2001-2015 Microchip Technology Inc. DS20001392E-page 9 TC1413/TC1413N 8-Lead SOIC (3.90 mm) Example TC1413C e3 1318 OA^^ 256 NNN OR TC1413 COA1318 256 8-Lead MSOP (3x3 mm) Example 1413E 318256 DS20001392E-page 10 2001-2015 Microchip Technology Inc. TC1413/TC1413N /HDG3ODVWLF'XDO,Q/LQH3$PLO%RG\>3',3@ 1RWH For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D A N B E1 NOTE 1 1 2 TOP VIEW E C A2 A 3/$1( L c A1 e eB 8X b1 8X b .010 C SIDE VIEW END VIEW Microchip Technology Drawing No. C04-018D Sheet 1 of 2 2001-2015 Microchip Technology Inc. DS20001392E-page 11 TC1413/TC1413N /HDG3ODVWLF'XDO,Q/LQH3$PLO%RG\>3',3@ 1RWH For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging ALTERNATE LEAD DESIGN (VENDOR DEPENDENT) DATUM A DATUM A b b e 2 e 2 e Units Dimension Limits Number of Pins N e Pitch Top to Seating Plane A Molded Package Thickness A2 Base to Seating Plane A1 Shoulder to Shoulder Width E Molded Package Width E1 Overall Length D Tip to Seating Plane L c Lead Thickness Upper Lead Width b1 b Lower Lead Width Overall Row Spacing eB § e MIN .115 .015 .290 .240 .348 .115 .008 .040 .014 - INCHES NOM 8 .100 BSC .130 .310 .250 .365 .130 .010 .060 .018 - MAX .210 .195 .325 .280 .400 .150 .015 .070 .022 .430 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. § Significant Characteristic 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side. 4. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing No. C04-018D Sheet 2 of 2 DS20001392E-page 12 2001-2015 Microchip Technology Inc. TC1413/TC1413N Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2001-2015 Microchip Technology Inc. DS20001392E-page 13 TC1413/TC1413N Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20001392E-page 14 2001-2015 Microchip Technology Inc. TC1413/TC1413N !"#$%& ' ! "#$%&"'"" ($) % *++&&&! !+$ 2001-2015 Microchip Technology Inc. DS20001392E-page 15 TC1413/TC1413N 8$ 1RWH For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20001392E-page 16 2001-2015 Microchip Technology Inc. TC1413/TC1413N UA Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2001-2015 Microchip Technology Inc. DS20001392E-page 17 TC1413/TC1413N 8-Lead Plastic Micro Small Outline Package (UA) [MSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20001392E-page 18 2001-2015 Microchip Technology Inc. TC1413/TC1413N APPENDIX A: REVISION HISTORY Revision E (February 2015) The following is the list of modifications: • Updated the values for electrostatic discharge in the Features and General Description columns. • Updated the Pin Description table in Section 3.0, Pin Descriptions. • Updated package marking information and drawings in Section 5.0, Packaging Information. • Minor grammatical and spelling corrections. Revision D (December 2012) • Added a note to each package outline drawing. Revision C (March 2003) • Undocumented changes. Revision B (May 2001) • Undocumented changes. Revision A (March 2001) • Original Release of this Document. 2001-2015 Microchip Technology Inc. DS20001392E-page 19 TC1413/TC1413N NOTES: DS20001392E-page 20 2001-2015 Microchip Technology Inc. TC1413/TC1413N PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device X /XX Temperature Range Package Examples: a) b) Device: TC1413: 3A Single MOSFET Driver, Inverting TC1413N: 3A Single MOSFET Driver, Non-Inverting Temperature Range: C E Package: OA = Plastic SOIC, (150 mil Body), 8-lead OA713 = Plastic SOIC, (150 mil Body), 8-lead (Tape and Reel) UA = Plastic Micro Small Outline (MSOP), 8-lead * UA713 = Plastic Micro Small Outline (MSOP), 8-lead * (Tape and Reel) PA = Plastic DIP (300 mil Body), 8-lead c) = = 0°C to +70°C -40°C to +85°C TC1413COA: 3A Single MOSFET driver, SOIC package, 0°C to +70°C. TC1413CPA: 3A Single MOSFET driver, PDIP package, 0°C to +70°C. TC1413EUA713:Tape and Reel, 3A Single MOSFET driver, MSOP package, -40°C to +85°C. a) TC1413NCPA: b) TC1413NEPA: c) TC1413NEUA: * MSOP package is only available in E-Temp. 2001-2015 Microchip Technology Inc. 3A Single MOSFET driver, PDIP package, 0°C to +70°C. 3A Single MOSFET driver, PDIP package, -40°C to +85°C. 3A Single MOSFET driver, MSOP package, -40°C to +85°C. DS20001392E-page 21 TC1413/TC1413N NOTES: DS20001392E-page 22 2001-2015 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, MediaLB, MOST, MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. The Embedded Control Solutions Company and mTouch are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet, KleerNet logo, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, RightTouch logo, REAL ICE, SQI, Serial Quad I/O, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2001-2015, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. ISBN: 978-1-63277-094-3 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2001-2015 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS20001392E-page 23 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Germany - Dusseldorf Tel: 49-2129-3766400 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Hong Kong Tel: 852-2943-5100 Fax: 852-2401-3431 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 Austin, TX Tel: 512-257-3370 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Canada - Toronto Tel: 905-673-0699 Fax: 905-673-6509 China - Dongguan Tel: 86-769-8702-9880 China - Hangzhou Tel: 86-571-8792-8115 Fax: 86-571-8792-8116 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Germany - Pforzheim Tel: 49-7231-424750 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Italy - Venice Tel: 39-049-7625286 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-213-7828 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Poland - Warsaw Tel: 48-22-3325737 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 01/27/15 DS20001392E-page 24 2001-2015 Microchip Technology Inc.