MURS120T3 D

MURS120T3G Series,
SURS8120T3G Series
Surface Mount
Ultrafast Power Rectifiers
MURS105T3G, MURS110T3G, MURS115T3G,
MURS120T3G, MURS140T3G, MURS160T3G,
SURS8105T3G, SURS8110T3G, SURS8115T3G,
SURS8120T3G, SURS8140T3G, SURS8160T3G
http://onsemi.com
ULTRAFAST RECTIFIERS
1.0 AMPERE, 50−600 VOLTS
Ideally suited for high voltage, high frequency rectification, or as
free wheeling and protection diodes in surface mount applications
where compact size and weight are critical to the system.
Features
•
•
•
•
•
•
•
Small Compact Surface Mountable Package with J−Bend Leads
Rectangular Package for Automated Handling
High Temperature Glass Passivated Junction
Low Forward Voltage Drop (0.71 to 1.05 V Max @ 1.0 A, TJ = 150°C)
AEC−Q101 Qualified and PPAP Capable
SURS8 Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements
These are Pb−Free Packages
Mechanical Characteristics:
• Case: Epoxy, Molded
• Weight: 95 mg (Approximately)
• Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
• Lead and Mounting Surface Temperature for Soldering Purposes:
•
•
260°C Max. for 10 Seconds
Polarity: Polarity Band Indicates Cathode Lead
ESD Rating:
♦ Human Body Model = 3B (> 8 kV)
♦ Machine Model = C (> 400 V)
SMB
CASE 403A
MARKING DIAGRAM
AYWW
U1x G
G
A
Y
WW
U1
=
=
=
=
Assembly Location*
Year
Work Week
Device Code
x = A, B, C, D, G, or J
G
= Pb−Free Package
(Note: Microdot may be in either location)
* The Assembly Location code (A) is front side
optional. In cases where the Assembly Location is
stamped in the package bottom (molding ejecter
pin), the front side assembly code may be blank.
ORDERING INFORMATION
See detailed ordering and shipping information in the table on
page 2 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking table
on page 2 of this data sheet.
© Semiconductor Components Industries, LLC, 2013
May, 2013 − Rev. 12
1
Publication Order Number:
MURS120T3/D
MURS120T3G Series, SURS8120T3G Series
MAXIMUM RATINGS
MURS/SURS8
Symbol
105T3
110T3
115T3
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
VRRM
VRWM
VR
50
100
150
Average Rectified Forward Current
IF(AV)
1.0 @ TL = 155°C
2.0 @ TL = 145°C
1.0 @ TL = 150°C
2.0 @ TL = 125°C
A
Non−Repetitive Peak Surge Current, (Surge applied
at rated load conditions halfwave, single phase, 60 Hz)
IFSM
40
35
A
Rating
Operating Junction Temperature
TJ
120T3
140T3
160T3
Unit
200
400
600
V
*65 to +175
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
THERMAL CHARACTERISTICS
MURS/SURS8
Rating
Symbol
Thermal Resistance
Junction−to−Lead (TL = 25°C)
105T3
115T3
110T3
RqJL
120T3
140T3
160T3
Unit
°C/W
13
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage (Note 1)
(iF = 1.0 A, TJ = 25°C)
(iF = 1.0 A, TJ = 150°C)
vF
Maximum Instantaneous Reverse Current (Note 1)
(Rated DC Voltage, TJ = 25°C)
(Rated DC Voltage, TJ = 150°C)
iR
Maximum Reverse Recovery Time
(iF = 1.0 A, di/dt = 50 A/ms)
(iF = 0.5 A, iR = 1.0 A, IR to 0.25 A)
trr
Maximum Forward Recovery Time
(iF = 1.0 A, di/dt = 100 A/ms, Rec. to 1.0 V)
tfr
Typical Peak Reverse Recovery Current
(IF = 1.0 A, di/dt = 50 A/ms)
IRM
0.875
0.71
1.25
1.05
2.0
50
5.0
150
35
25
75
50
25
50
0.75
1.60
V
mA
ns
ns
A
1. Pulse Test: Pulse Width = 300 ms, Duty Cycle v 2.0%.
DEVICE MARKING AND ORDERING INFORMATION
Marking
Package
Shipping†
MURS105T3G,
SURS8105T3G
U1A
SMB
(Pb−Free)
2,500 Units / Tape & Reel
MURS110T3G,
SURS8110T3G
U1B
SMB
(Pb−Free)
2,500 Units / Tape & Reel
MURS115T3G,
SURS8115T3G
U1C
SMB
(Pb−Free)
2,500 Units / Tape & Reel
MURS120T3G,
SURS8120T3G
U1D
SMB
(Pb−Free)
2,500 Units / Tape & Reel
MURS140T3G,
SURS8140T3G
U1G
SMB
(Pb−Free)
2,500 Units / Tape & Reel
MURS160T3G,
SURS8160T3G
U1J
SMB
(Pb−Free)
2,500 Units / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
2
MURS120T3G Series, SURS8120T3G Series
MURS105T3G, MURS110T3G, MURS115T3G, MURS120T3G,
SURS8105T3G, SURS8110T3G, SURS8115T3G, SURS8120T3G
10
IR, REVERSE CURRENT (m A)
7.0
5.0
3.0
i , INSTANTANEOUS FORWARD CURRENT (AMPS)
F
175°C
100°C
2.0
TC = 25°C
1.0
80
40
20
8.0
4.0
2.0
0.8
0.4
0.2
TJ = 175°C
TJ = 100°C
0.08
0.04
0.02
0.008
0.004
0.002
0.7
TJ = 25°C
0
20
40
0.5
60
80
100
120
140
160
180 200
VR, REVERSE VOLTAGE (VOLTS)
Figure 2. Typical Reverse Current*
*The curves shown are typical for the highest voltage device in the
voltage grouping. Typical reverse current for lower voltage selections
can be estimated from these same curves if applied VR is sufficiently
below rated VR.
0.3
0.2
50
0.1
45
0.07
NOTE: TYPICAL
CAPACITANCE AT
0 V = 45 pF
C, CAPACITANCE (pF)
40
0.05
0.03
0.02
35
30
25
20
15
10
0.01
5.0
0.3 0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
0
0
vF, INSTANTANEOUS VOLTAGE (VOLTS)
10
20
Figure 1. Typical Forward Voltage
30
40
50
60
70
80
90
100
VR, REVERSE VOLTAGE (VOLTS)
10
RATED VOLTAGE APPLIED
RqJC = 13°C/W
TJ = 175°C
9.0
8.0
7.0
6.0
5.0
4.0
DC
3.0
2.0
SQUARE WAVE
1.0
0
80
90
100
110
120
130
140
150
160
170
180
PF(AV) , AVERAGE POWER DISSIPATION (WATTS)
IF(AV) , AVERAGE FORWARD CURRENT (AMPS)
Figure 3. Typical Capacitance
5.0
TJ = 175°C
4.0
5.0
I
10
(CAPACITANCELOAD) PK + 20
I
3.0
AV
2.0
DC
SQUARE WAVE
1.0
0
0
0.5
1.0
1.5
2.0
TC, CASE TEMPERATURE (°C)
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
Figure 4. Current Derating, Case
Figure 5. Power Dissipation
http://onsemi.com
3
2.5
MURS120T3G Series, SURS8120T3G Series
MURS140T3G, MURS160T3G, SURS8140T3G, SURS8160T3G
10
IR, REVERSE CURRENT (m A)
7.0
175°C
5.0
100°C
3.0
i , INSTANTANEOUS FORWARD CURRENT (AMPS)
F
TC = 25°C
2.0
1.0
0.7
400
200
80
40
20
8.0
4.0
2.0
0.8
0.4
0.2
0.08
0.04
0.02
0.008
0.004
TJ = 175°C
TJ = 100°C
TJ = 25°C
0
100
200
0.5
300
400
500
600
700
VR, REVERSE VOLTAGE (VOLTS)
Figure 7. Typical Reverse Current*
*The curves shown are typical for the highest voltage device in the
voltage grouping. Typical reverse current for lower voltage selections
can be estimated from these same curves if applied VR is sufficiently
below rated VR.
0.3
0.2
25
0.1
0.07
NOTE: TYPICAL
CAPACITANCE AT
0 V = 24 pF
C, CAPACITANCE (pF)
20
0.05
0.03
0.02
15
10
5.0
0.01
0.3 0.5
0.7
0.9
1.1
1.3
1.5
1.7
1.9
2.1
2.3
0
0
vF, INSTANTANEOUS VOLTAGE (VOLTS)
4.0
8.0
Figure 6. Typical Forward Voltage
12
16
20
24
28
32
36
40
VR, REVERSE VOLTAGE (VOLTS)
10
RATED VOLTAGE APPLIED
RqJC = 13°C/W
TJ = 175°C
9.0
8.0
7.0
6.0
5.0
4.0
DC
3.0
2.0
SQUARE WAVE
1.0
0
0
20
40
60
80
100
120
140
160
180
200
PF(AV) , AVERAGE POWER DISSIPATION (WATTS)
IF(AV) , AVERAGE FORWARD CURRENT (AMPS)
Figure 8. Typical Capacitance
5.0
4.0
5.0
10
(CAPACITANCE LOAD)
I
PK + 20
I
SQUARE WAVE
AV
3.0
DC
TJ = 175°C
2.0
1.0
0
0
0.5
1.0
1.5
2.0
TC, CASE TEMPERATURE (°C)
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
Figure 9. Current Derating, Case
Figure 10. Power Dissipation
http://onsemi.com
4
2.5
MURS120T3G Series, SURS8120T3G Series
PACKAGE DIMENSIONS
SMB
CASE 403A−03
ISSUE J
HE
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION b SHALL BE MEASURED WITHIN DIMENSION L1.
E
b
DIM
A
A1
b
c
D
E
HE
L
L1
D
POLARITY INDICATOR
OPTIONAL AS NEEDED
MIN
1.95
0.05
1.96
0.15
3.30
4.06
5.21
0.76
MILLIMETERS
NOM
MAX
2.30
2.47
0.10
0.20
2.03
2.20
0.23
0.31
3.56
3.95
4.32
4.60
5.44
5.60
1.02
1.60
0.51 REF
MIN
0.077
0.002
0.077
0.006
0.130
0.160
0.205
0.030
INCHES
NOM
0.091
0.004
0.080
0.009
0.140
0.170
0.214
0.040
0.020 REF
MAX
0.097
0.008
0.087
0.012
0.156
0.181
0.220
0.063
A
L
L1
A1
c
SOLDERING FOOTPRINT*
2.261
0.089
2.743
0.108
2.159
0.085
SCALE 8:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
5
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MURS120T3/D