Data Sheet • Mann Series Fo u r D i g i t , P r o g r a m m a b l e D i s p l a y s with Alarms and Analogue Output P M X 4 0 0 T M P Te m p e r a t u re D i s p l a y P M X 4 0 0 H Z X F re q u e n c y D i s p l a y / Ta c h o m e t e r • Bright four digit LED display in engineering units • Up to 4 alarm channels • Optional analogue output • AC or DC powered • Fully Isolated • LED alarm status indication • 1/8 DIN standard front with IP65 rating • Integral power supply for active input devices • Indicate and change setpoints in engineering units • Full on–site programming from the front panel keypad % \ Australia Weidmüller Pty Ltd. 43 Huntingwood Drive, Huntingwood NSW 2148 Phone +61 (0) 2 9671 9999 Fax +61 (0) 2 9671 9900 [email protected] www.mannseries.com United Kingdom Other countries Weidmüller Ltd. 1 Abbey Wood Road, Kings Hill West Malling, Kent ME19 4YT Phone +44 1732-877032 Fax +44 1732-873873 [email protected] www.weidmueller.com Weidmüller Interface GmbH & Co. Postfach 3030 32720 Detmold Phone +495231-14-0 Fax +495231-14-2083 [email protected] www.weidmueller.com PMX400 Series Displays PMX400 Series The PMX400 series consists of two models: • Temperature display • Frequency display/Tachometer Each model supports a wide variety of input signal types and ranges. The analogue and alarm outputs are optional, except for the HZX which comes with two open collector alarms as standard. Units can be ordered with two or four SPDT relay channels. Alarm channel four can be set up as a group/siren alarm which operates according to the state of the other three alarms. Note: if your process measurement is represented by a current or voltage signal you may be interested in the PMX420 Series displays. NN NN -2700 N N N N NN !, 1"/&-5)*$,/&44.BYNN !, !, NNNN $65065 N N N N N N N N N N NN N N ("4,&5 !, General Technical Data Display Type Full 4 digit, red 14.2 mm LED Scaling To display in % or engineering units Display range –9999 to 9999 Status indicators Alarm ch 1–4 and key status General set–up menu options Display HIBr Analogue output (optional) dp= Display brightness High or Low Type Analogue current/voltage Display Decimal Point 0.000 to 0000 Scaling To represent any portion of the input range dLO= Display low [Value] Range Any range inside the limits 0–22 mA or 0–11 V dHI= Display high [Value] Current drive Up to 850Ω load (at 20mA) Voltage drive True voltage source (up to 20mA) Ip=1 Input type See individual units Output ripple Less than 20mV P/P IPL= Input range low [Value] Output action Direct/reverse IPH= Input range high [Value] dF=2 Input filtering 1 to 99 Inputs Input filtering Type Digital filter (programmable) Damping factor 1 to 99 (default = 2) Analogue output AOPY Analogue Output Enable/disable Output low [Value] Typically ±0.1% of span OPL= [Value] Better than 0.05% OPH= Output high ±0.02% of span OP=d Output sense Direct or reversed General Accuracy Linearity Repeatability Alarms 1–4 (general options) Temperature drift Less than 0.02% span/°C Enable/disable 0.1% per 10,000 hours A12y Alarms 1 & 2 Long term drift Frequency response –3dB point = 5Hz A34y Alarms 3 & 4 Enable/disable 300 mS for 10–90% output change (digital filtering = 1) SECy Setpoint security On–the–fly–changes or locked nOr Alarm reset mode Manual or Automatic Response time Insulation Co-ordination Ports Input / Output / Case Rated Insulation Voltage 300Veff Overvoltage Category III Impulse Withstand Alarm options (set for each channel) A1nE Output Coil energisation Normally Energised or De–energised 4kV (1.2 / 50) a1=H Alarm Type High/Low (and Siren/ Group for channel four only) Operating temperature 0 to 60 °C Storage temperature –25 to +70 °C SP1= 50.00 Setpoint e.g., 50.00 units According to display range Pollution Degree 2 Relative humidity 10–90% (non–condensing) db1= 10.00 Introduces deadband e.g., 10.00 units From 1 count to display range Panel mount dl1= 20 Alarm Timer Delay e.g., 20 seconds 0–4200s (default = 0s) Environmental Conditions Housing Type Front bezel 1/8 DIN format with IP65 rating Approvals Mark DC Powered Units only \ E205105 CAN/CSA C22.2 No. 142-M1987, 1st Edition UL508, 17th Edition DC Powered Units only % LV Directive EMC EN50178:1998 BS EN 61326:1998 + A2 Page 2 Standard Subject to technical alterations without notice • Printed in Australia • 7940015660 • 25/10/2007 Universal Temperature Indicator PMX400 Series Displays PMX400TMP • Accepts thermocouple, RTD or mV inputs • Total sensor diagnostics • Indicates temperature in °C or °F • Configure without the need to calibrate • Indicates setpoints in °C or °F • Automatic CJC for thermocouple inputs • Automatic lead length compensation for RTD inputs Options The basic software will control the optional analogue outputs and alarm channels without modification. So, to retrofit an option, you can simply add a card, calibrate and setup for your installation from the front panel. %\ Technical Data Connections Display Scaling To display in °C, °F or mV Terminal Signal 1 Neutral / − 2 Live / + Power supply Inputs Type Thermocouple, PT100 RTD or mV 3 Output + Standard ranges: Any range inside limits shown (no recalibration required) 4 Current − J Type Thermocouple –50°C (–58°F) to 870°C (1598°F) 5 Voltage − N Type Thermocouple –50°C (–58°F) to 1300°C (2372°F) 6 Security Link T Type Thermocouple –50°C (–58°F) to 400°C (752°F) 7 Security Link Link to allow access to the set-up mode (normally not connected) E Type Thermocouple –50°C (–58°F) to 700°C (1292°F) 8 B Type Thermocouple 0°C (32°F) to 1820°C (3308°F) 9 S Type Thermocouple –50°C (–58°F) to 1768°C (3214°F) 10 CJC Board (white mark alligns with terminal 11) Thermocouple inputs R Type Thermocouple –50°C (–58°F) to 1768°C (3214°F) 11 mV signals –200.00mV to 200.00mV 12 RTD (Pt100) –220.0°C (–364.0°F) to 820.0°C (1508.0°F) 8 Cold junction compensation for thermocouple inputs Automatic 9 Lead length compensation for RTD inputs Automatic 10 B 11 Bsense 12 A Not used Not used Power supply Type AC or DC powered AC (selectable) 100 – 132 Vac (47–63Hz) or 200 – 264 Vac (47–63Hz) 8 DC 20–28Vdc (others on request) 9 Power usage AC 6VA or 6W at 24Vdc 10 mV input − 11 mV input + Type SPDT relay contacts 12 Not used Rating 3A at 240Vac (resistive) 3A at 24Vdc (resistive) 13 Normally Closed 14 Common 15 Normally Open 16 Normally Closed 17 Common 1kV between channels General Sampling rate 5 samples per second Options /AO With analogue output fitted 18 Normally Open /4RO With all alarm channels fitted 19 Normally Closed 10 Common 21 Normally Open 22 Normally Closed 23 Common 24 Normally Open Notes Ordering Information Type (Model Supply/Options) RTD inputs Not used Alarm ouputs (all channels) Isolation Analogue output (/AO option only) Cat. No. PMX400TMP 24Vdc 7940017862 PMX400TMP 24Vdc/4RO/AO 7940012968 Millivolt inputs Alarm Channel One (/4RO option only) Alarm Channel Two (/4RO option only) Alarm Channel Three (/4RO option only) Alarm Channel Four (/4RO option only) For other ranges please specify PMX400TMP 1/2 where: 1 = Supply and 2 = Options Page 3 Subject to technical alterations without notice • Printed in Australia • 7940015660 • 25/10/2007 PMX400 Series Displays PMX400HZX • Measures frequency of signals from industrial sensors • Provides power for active input devices • Two alarm channels • Debounce for contact closure inputs Options The basic software will control the optional analogue outputs and alarm channels without modification. So, to retrofit an option, you can simply add a card, calibrate and setup for your installation from the front panel. Universal Frequency Indicator/Tachometer Inputs Inputs can be taken from many sources, including: • NAMUR sensors • 3–wire PNP/NPN sensors • PNP/NPN open collector outputs • TTL logic • Solid State Switches • Low and high voltage pulses • Volt–free contacts %\ Connections Technical Data Terminal Signal Display 1 Neutral / − 2 Live / + 3 Output + 4 Ouput − 5 Common 6 Channel 1 7 Channel 2 Scaling Power supply To display in engineering units Inputs Type Programmable frequency Range Any range within the limits shown Analogue output (/AO option only) Alarm Channel One and Alarm Channel Two Span range Zero range Resolution 0 to 9.999Hz 0 to 9.998Hz 0.001Hz 0 to 99.99Hz 0 to 99.98Hz 0.01Hz 0 to 999.9Hz 0 to 999.8Hz 0.1Hz 8 Security Link 0 to 9999Hz 0 to 9998Hz 1Hz 9 Pull up/down Inputs/Security link Link 12 & 8 for set-up mode (otherwise leave disconnected) Sensor power output Nominally 12 Vdc (to 25 mA) – others on request (/FPS option) 10 Signal − / 0 V Input voltage range 50 mVac to 250 Vac or 3 Vdc to 250 Vdc 11 Signal + 12 +12Vdc out Power supply Type AC or DC powered AC (selectable) 100 – 132 Vac (47–63Hz) or 200 – 264 Vac (47–63Hz) DC 24 Vdc ±10% (others on request) Power usage AC 6VA or 6W at 24Vdc See user manual for full explanation of input connections 13 Normally Closed 14 Common 15 Normally Open 16 Normally Closed 17 Common 18 Normally Open Alarm Channel Three (/RO option only) Alarm ouputs (channels one and two) Type NPN open collector transistor type Operation Switched to 0 V when “on“ Rating to 200mA “on“ state current or 50 Vdc “off“ state voltage Note: back–emf protection must be used for inductive loads Isolation Common negative rail Alarm Channel Four (/RO option only) Alarm ouputs (channels three and four) Type SPDT relay contacts Rating 3A at 240Vac (resistive) 3A at 24Vdc (resistive) Isolation 1kV between channels General Response time 220mS (10–90mS, df=1) Options /AO With analogue output fitted /RO With alarm channels three and four fitted /FPS Custom input sensor supply voltage. State voltage, e.g., PMX400HZX/.../FPS/24Vdc Ordering Information Type (Model Supply/Options) Cat. No. PMX400HZX 24Vdc 7940015595 PMX400HZX 24Vdc/RO/AO 7940011979 For other ranges please specify PMX400HZX 1/2 where: 1 = Supply and 2 = Options Page 4 Subject to technical alterations without notice • Printed in Australia • 7940015660 • 25/10/2007