HFA1405 ® DUCT E PRO PRODUCT T E L O OBS ITUTE UBSTSheet SData E 45 5 L IB 0, E L5 POSS EL248 Quad, 560MHz, Low Power, Video Operational Amplifier March 1, 2005 FN3604.9 Features • Low Supply Current . . . . . . . . . . . . . . . . . 5.8mA/Op Amp The HFA1405 is a quad, high speed, low power current feedback amplifier built with Intersil’s proprietary complementary bipolar UHF-1 process. • High Input Impedance . . . . . . . . . . . . . . . . . . . . . . . 1MΩ • Wide -3dB Bandwidth (AV = +2). . . . . . . . . . . . . . 560MHz These amplifiers deliver up to 560MHz bandwidth and 2500V/µs slew rate, on only 58mW of quiescent power. They are specifically designed to meet the performance, power, and cost requirements of high volume video applications. The excellent gain flatness and differential gain/phase performance make these amplifiers well suited for component or composite video applications. Video performance is maintained even when driving a back terminated cable (RL = 150Ω), and degrades only slightly when driving two back terminated cables (RL = 75Ω). RGB applications will benefit from the high slew rates, and high full power bandwidth. The HFA1405 is a pin compatible, low power, high performance upgrade for the popular Intersil HA5025, and for the CLC414 and CLC415. • Very Fast Slew Rate . . . . . . . . . . . . . . . . . . . . . . 2500V/µs • Gain Flatness (to 50MHz). . . . . . . . . . . . . . . . . . . . . ±0.03dB • Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.02% • Differential Phase . . . . . . . . . . . . . . . . . . . . . 0.03 Degrees • All Hostile Crosstalk (5MHz) . . . . . . . . . . . . . . . . . . -60dB • Pin Compatible Upgrade to HA5025, CLC414, and CLC415 Applications • Flash A/D Drivers • Professional Video Processing • Video Digitizing Boards/Systems • Multimedia Systems Part # Information PART NUMBER • RGB Preamps TEMP. RANGE (oC) PACKAGE PKG. DWG. # HFA1405IB -40 to 85 14 Ld SOIC M14.15 HFA1405IP -40 to 85 14 Ld PDIP E14.3 • Hand Held and Miniaturized RF Equipment • Battery Powered Communications High Speed Op Amp DIP Evaluation Board • High Speed Oscilloscopes and Analyzers Related Literature • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” Pinout HFA1405 (PDIP, SOIC) TOP VIEW 14 OUT 4 OUT 1 1 -IN 1 2 - 12 +IN 4 +IN 1 3 11 V- V+ 4 OUT 2 7 1 + -IN 2 6 + +IN 2 5 13 -IN 4 + - + HA5025EVAL • Medical Imaging - - 10 +IN 3 9 -IN 3 8 OUT 3 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2000-2005. All Rights Reserved All other trademarks mentioned are the property of their respective owners. HFA1405 Absolute Maximum Ratings TA = 25oC Thermal Information Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11V DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSUPPLY Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V Output Current (Note 2) . . . . . . . . . . . . . . . . .Short Circuit Protected 30mA Continuous 60mA ≤ 50% Duty Cycle ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . . 600V Thermal Resistance (Typical, Note 1) θJA (oC/W) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Maximum Junction Temperature (Die) . . . . . . . . . . . . . . . . . . . 175oC Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 2. Output is short circuit protected to ground. Brief short circuits to ground will not degrade reliability, however continuous (100% duty cycle) output current must not exceed 30mA for maximum reliability. Electrical Specifications VSUPPLY = ±5V, AV = +1, RF = 510Ω , RL = 100Ω , Unless Otherwise Specified PARAMETER HFA1405IB (SOIC) HFA1405IP (PDIP) (NOTE 4) TEST LEVEL TEMP( oC) MIN TYP MAX MIN TYP MAX UNITS A 25 - 2 5 - 2 5 mV A Full - 3 8 - 3 8 mV B Full - 1 10 - 1 10 µV/oC ∆VCM = ±1.8V A 25 45 48 - 45 48 - dB ∆VCM = ±1.8V A 85 43 46 - 43 46 - dB ∆VCM = ±1.2V A -40 43 46 - 43 46 - dB ∆VPS = ±1.8V A 25 48 52 - 48 52 - dB ∆VPS = ±1.8V A 85 46 48 - 46 48 - dB TEST CONDITIONS INPUT CHARACTERISTICS Input Offset Voltage Average Input Offset Voltage Drift Input Offset Voltage Common-Mode Rejection Ratio Input Offset Voltage Power Supply Rejection Ratio ∆VPS = ±1.2V A -40 46 48 - 46 48 - dB Non-Inverting Input Bias Current A 25 - 6 15 - 6 15 µA A Full - 10 25 - 10 25 µA Non-Inverting Input Bias Current Drift B Full - 5 60 - 5 60 nA/oC ∆VPS = ±1.8V A 25 - 0.5 1 - 0.5 1 µA/V ∆VPS = ±1.8V A 85 - 0.8 3 - 0.8 3 µA/V ∆VPS = ±1.2V A -40 - 0.8 3 - 0.8 3 µA/V Non-Inverting Input Bias Current Power Supply Sensitivity Non-Inverting Input Resistance ∆VCM = ±1.8V A 25 0.8 1.2 - 0.8 1.2 - MΩ ∆VCM = ±1.8V A 85 0.5 0.8 - 0.5 0.8 - MΩ ∆VCM = ±1.2V A -40 0.5 0.8 - 0.5 0.8 - MΩ A 25 - 2 7.5 - 2 7.5 µA A Full - 5 15 - 5 15 µA B Full - 60 200 - 60 200 nA/oC ∆VCM = ±1.8V A 25 - 3 6 - 3 6 µA/V ∆VCM = ±1.8V A 85 - 4 8 - 4 8 µA/V ∆VCM = ±1.2V A -40 - 4 8 - 4 8 µA/V Inverting Input Bias Current Inverting Input Bias Current Drift Inverting Input Bias Current Common-Mode Sensitivity 2 HFA1405 Electrical Specifications VSUPPLY = ±5V, AV = +1, RF = 510Ω , RL = 100Ω , Unless Otherwise Specified (Continued) PARAMETER HFA1405IP (PDIP) TEMP( oC) MIN TYP MAX MIN TYP MAX UNITS ∆VPS = ±1.8V A 25 - 2 5 - 2 5 µA/V ∆VPS = ±1.8V A 85 - 4 8 - 4 8 µA/V TEST CONDITIONS Inverting Input Bias Current Power Supply Sensitivity HFA1405IB (SOIC) (NOTE 4) TEST LEVEL ∆VPS = ±1.2V A -40 - 4 8 - 4 8 µA/V Inverting Input Resistance C 25 - 60 - - 60 - Ω Input Capacitance B 25 - 1.4 - - 2.2 - pF Input Voltage Common Mode Range (Implied by VIO CMRR, +RIN, and -IB-IAS CMS Tests) A 25, 85 ±1.8 ±2.4 - ±1.8 ±2.4 - V A -40 ±1.2 ±1.7 - ±1.2 ±1.7 - V f = 100kHz B 25 - 3.5 - - 3.5 - nV/√Hz Non-Inverting Input Noise Current f = 100kHz Density Input Noise Voltage Density B 25 - 2.5 - - 2.5 - pA/√Hz Inverting Input Noise Current Density f = 100kHz B 25 - 20 - - 20 - pA/√Hz AV = -1 C 25 - 500 - - 500 - kΩ AV = -1 B 25 - 420 - - 360 - MHz AV = +2 B 25 - 560 - - 400 - MHz AV = +6 B 25 - 140 - - 100 - MHz AV = -1 B 25 - 260 - - 260 - MHz AV = +2 B 25 - 165 - - 165 - MHz TRANSFER CHARACTERISTICS Open Loop Transimpedance Gain AC CHARACTERISTICS (Note 3) -3dB Bandwidth (VOUT = 0.2VP-P, Notes 3, 5) Full Power Bandwidth (VOUT = 5VP-P, Notes 3, 5) Gain Flatness (VOUT = 0.2VP-P, Notes 3, 5) AV = +6 B 25 - 140 - - 100 - MHz AV = -1, 25MHz B 25 - ±0.03 - - ±0.04 - dB AV = -1, 50MHz B 25 - ±0.04 - - ±0.04 - dB AV = -1, 100MHz B 25 - ±0.09 - - ±0.06 - dB AV = +2, 25MHz B 25 - ±0.03 - - ±0.04 - dB AV = +2, 50MHz B 25 - ±0.03 - - ±0.04 - dB AV = +2, 100MHz B 25 - ±0.07 - - ±0.06 - dB AV = +6, 15MHz B 25 - ±0.08 - - ±0.08 - dB AV = +6, 30MHz Minimum Stable Gain Crosstalk (AV = +1, All Channels Hostile, Note 5) B 25 - ±0.19 - - ±0.27 - dB A Full - 1 - - 1 - V/V 5MHz B 25 - -60 - - -55 - dB 10MHz B 25 - -56 - - -52 - dB OUTPUT CHARACTERISTICS AV = +2 (Note 3), Unless Otherwise Specified A 25 ±3 ±3.4 - ±3 ±3.4 - V A Full ±2.8 ±3 - ±2.8 ±3 - V A 25, 85 50 60 - 50 60 - mA A -40 28 42 - 28 42 - mA Output Short Circuit Current B 25 - 90 - - 90 - mA Closed Loop Output Impedance B 25 - 0.2 - - 0.2 - Ω Output Voltage Swing (Note 5) AV = -1, RL = 100Ω Output Current (Note 5) AV = -1, RL = 50Ω Second Harmonic Distortion (VOUT = 2VP-P, Note 5) 10MHz B 25 - -51 - - -51 - dBc 20MHz B 25 - -46 - - -46 - dBc Third Harmonic Distortion (VOUT = 2VP-P, Note 5) 10MHz B 25 - -63 - - -63 - dBc 20MHz B 25 - -56 - - -56 - dBc 3 HFA1405 Electrical Specifications VSUPPLY = ±5V, AV = +1, RF = 510Ω , RL = 100Ω , Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS (NOTE 4) TEST LEVEL HFA1405IB (SOIC) TEMP( oC) MIN HFA1405IP (PDIP) TYP MAX MIN TYP MAX UNITS TRANSIENT CHARACTERISTICS AV = +2 (Note 3), Unless Otherwise Specified Rise and Fall Times (VOUT = 0.5VP-P, Note 3) Overshoot (VOUT = 0.5VP-P, VIN tRISE = 1ns, Notes 3, 6) Slew Rate (VOUT = 5VP-P, Notes 3, 5) AV = +2 B 25 - 0.8 - - 0.9 - ns AV = +6 B 25 - 2.9 - - 4 - ns AV = -1, +OS B 25 - 7 - - 3 - % AV = -1, -OS B 25 - 8 - - 13 - % AV = +2, +OS B 25 - 5 - - 7 - % AV = +2, -OS B 25 - 10 - - 11 - % AV = +6, +OS B 25 - 2 - - 2 - % AV = +6, -OS B 25 - 2 - - 2 - % AV = -1, +SR B 25 - 2500 - - 2500 - V/µs AV = -1, -SR B 25 - 1900 - - 1900 - V/µs AV = +2, +SR B 25 - 1700 - - 1600 - V/µs AV = +2, -SR B 25 - 1700 - - 1400 - V/µs AV = +6, +SR B 25 - 1500 - - 1000 - V/µs AV = +6, -SR B 25 - 1100 - - 1000 - V/µs B 25 - 23 - - 23 - ns Settling Time To 0.1% (VOUT = +2V to 0V Step, Note 5) To 0.05% Overdrive Recovery Time VIDEO CHARACTERISTICS B 25 - 30 - - 30 - ns To 0.025% B 25 - 37 - - 40 - ns VIN = ±2V B 25 - 8.5 - - 8.5 - ns AV = +2 (Note 3), Unless Otherwise Specified Differential Gain (f = 3.58MHz) RL = 150Ω B 25 - 0.02 - - 0.03 - % RL = 75Ω B 25 - 0.03 - - 0.06 - % RL = 150Ω B 25 - 0.03 - - 0.03 - Degrees RL = 75Ω B 25 - 0.06 - - 0.06 - Degrees Power Supply Range C 25 ±4.5 - ±5.5 ±4.5 - ±5.5 V Power Supply Current (Note 5) A 25 - 5.8 6.1 - 5.8 6.1 mA/Op Amp A Full - 5.9 6.3 - 5.9 6.3 mA/Op Amp Differential Phase (f = 3.58MHz) POWER SUPPLY CHARACTERISTICS NOTES: 3. The optimum feedback resistor depends on closed loop gain and package type. See the “Optimum Feedback Resistor” table in the Application Information section for details. 4. Test Level: A. Production Tested; B. Typical or Guaranteed Limit Based on Characterization; C. Design Typical for Information Only. 5. See Typical Performance Curves for more information. 6. Undershoot dominates for output signal swings below GND (e.g., 2VP-P), yielding a higher overshoot limit compared to the VOUT = 0V to 2V condition. See the “Application Information” section for details. Application Information Performance Differences Between Packages The amplifiers comprising the HFA1405 are high frequency current feedback amplifiers. As such, they are sensitive to feedback capacitance which destabilizes the op amp and causes overshoot and peaking. Unfortunately, the standard quad op amp pinout places the amplifier’s output next to its inverting input, thus making the package capacitance an unavoidable parasitic feedback capacitor. The larger 4 parasitic capacitance of the PDIP requires an inherently more stable amplifier, which yields a PDIP device with lower performance than the SOIC device - see Electrical Specification tables for details. Because of these performance differences, designers should evaluate and breadboard with the same package style to be used in production. Note that the “Typical Performance Curves” section has separate pulse and frequency response graphs for each HFA1405 package type. Graphs not labeled with a specific package type are applicable to all packages. Optimum Feedback Resistor Although a current feedback amplifier’s bandwidth dependency on closed loop gain isn’t as severe as that of a voltage feedback amplifier, there can be an appreciable decrease in bandwidth at higher gains. This decrease may be minimized by taking advantage of the current feedback amplifier’s unique relationship between bandwidth and RF. All current feedback amplifiers require a feedback resistor, even for unity gain applications, and RF, in conjunction with the internal compensation capacitor, sets the dominant pole of the frequency response. Thus, the amplifier’s bandwidth is inversely proportional to RF. The HFA1405 design is optimized for RF = 402Ω/510Ω (PDIP/SOIC) at a gain of +2. Decreasing RF decreases stability, resulting in excessive peaking and overshoot (Note: Capacitive feedback causes the same problems due to the feedback impedance decrease at higher frequencies). However, at higher gains the amplifier is more stable so RF can be decreased in a trade-off of stability for bandwidth. The table below lists recommended RF values for various gains, and the expected bandwidth. For good channel-tochannel gain matching, it is recommended that all resistors (termination as well as gain setting) be ±1% tolerance or better. TABLE 1. OPTIMUM FEEDBACK RESISTOR GAIN (ACL) RF (Ω) PDIP/SOIC BANDWIDTH (MHz) PDIP/SOIC -1 310/360 360/420 +1 510 (+RS = 510)/ 464 (+RS = 649) 300/375 +2 402/510 400/560 +5 NA/200 NA/330 +6 500/500 (Note) 100/140 +10 NA/180 NA/140 NOTE: RF = 500Ω is not the optimum value. It was chosen to match the RF of the CLC414 and CLC415, for performance comparison purposes. Performance at AV = +6 may be increased by reducing RF below 500Ω. Non-inverting Input Source Impedance For best operation, the DC source impedance seen by the non-inverting input should be ≥ 50Ω. This is especially important in inverting gain configurations where the noninverting input would normally be connected directly to GND. Pulse Undershoot The HFA1405 utilizes a quasi-complementary output stage to achieve high output current while minimizing quiescent supply current. In this approach, a composite device replaces the traditional PNP pulldown transistor. The composite device switches modes after crossing 0V, 5 resulting in added distortion for signals swinging below ground, and an increased undershoot on the negative portion of the output waveform (see Figure 6 and Figure 9). This undershoot isn’t present for small bipolar signals, or large positive signals (see Figure 4 and Figure 5). PC Board Layout The frequency response of this amplifier depends greatly on the amount of care taken in designing the PC board. The use of low inductance components such as chip resistors and chip capacitors is strongly recommended, while a solid ground plane is a must! Attention should be given to decoupling the power supplies. A large value (10µF) tantalum in parallel with a small value (0.1µF) chip capacitor works well in most cases. Terminated microstrip signal lines are recommended at the input and output of the device. Capacitance, parasitic or planned, connected to the output must be minimized, or isolated as discussed in the next section. Care must also be taken to minimize the capacitance to ground at the amplifier’s inverting input (-IN). The larger this capacitance, the worse the gain peaking, resulting in pulse overshoot and eventual instability. To reduce this capacitance the designer should remove the ground plane under traces connected to -IN, and keep connections to -IN as short as possible. An example of a good high frequency layout is the Evaluation Board shown in Figure 3. Driving Capacitive Loads Capacitive loads, such as an A/D input, or an improperly terminated transmission line will degrade the amplifier’s phase margin resulting in frequency response peaking and possible oscillations. In most cases, the oscillation can be avoided by placing a resistor (RS) in series with the output prior to the capacitance. Figure 1 details starting points for the selection of this resistor. The points on the curve indicate the RS and CL combinations for the optimum bandwidth, stability, and settling time, but experimental fine tuning is recommended. Picking a point above or to the right of the curve yields an overdamped response, while points below or left of the curve indicate areas of underdamped performance. RS and CL form a low pass network at the output, thus limiting system bandwidth well below the amplifier bandwidth of 560MHz. By decreasing RS as CL increases (as illustrated in the curve), the maximum bandwidth is obtained without sacrificing stability. In spite of this, bandwidth still decreases as the load capacitance increases. HFA1405 TOP LAYOUT SERIES OUTPUT RESISTANCE (Ω) 50 40 30 20 AV = +2 10 0 0 50 100 150 200 250 300 350 400 LOAD CAPACITANCE (pF) FIGURE 1. RECOMMENDED SERIES OUTPUT RESISTOR vs LOAD CAPACITANCE BOTTOM LAYOUT Evaluation Board The performance of the HFA1405 PDIP or SOIC can be evaluated using the HA5025 Evaluation Board. The HFA1405IB (SOIC) requires a SOIC to DIP adaptor like the Aries Electronics Part Number 14-350000-10. The schematic for the PDIP/SOIC amplifier 1 and the HA5025EVAL board layout are shown in Figure 2 and Figure 3. Resistors RF, RG , and +RS may require a change to values applicable to the HFA1405. To order evaluation board (part number HA5025EVAL), please contact your local sales office. FIGURE 3. EVALUATION BOARD LAYOUT FOR PDIP/SOIC 50Ω OUT RG RF 1 2 IN 50Ω +RS 3 14 13 + 12 4 11 5 10 0.1µF 6 9 7 8 -5V 0.1µF 10µF +5V 10µF GND GND FIGURE 2. EVALUATION BOARD SCHEMATIC FOR PDIP/SOIC 6 HFA1405 Typical Performance Curves VSUPPLY = ±5V, TA = 25oC, RF = Value From the Optimum Feedback Resistor Table, 160 1.6 AV = +2 120 SOIC 1.2 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (mV) RL = 100Ω, Unless Otherwise Specified 80 40 0 -40 AV = +2 SOIC 0.8 0.4 0 -0.4 -80 -0.8 -120 -1.2 -160 -1.6 TIME (5ns/DIV.) TIME (5ns/DIV.) FIGURE 5. LARGE SIGNAL POSITIVE PULSE RESPONSE FIGURE 4. SMALL SIGNAL PULSE RESPONSE 160 1.6 120 OUTPUT VOLTAGE (mV) OUTPUT VOLTAGE (V) 1.2 AV = +2 SOIC 0.8 0.4 0 -0.4 -0.8 AV = -1 SOIC 80 40 0 -40 -80 -120 -1.2 -160 -1.6 TIME (5ns/DIV.) TIME (5ns/DIV.) FIGURE 7. SMALL SIGNAL PULSE RESPONSE FIGURE 6. LARGE SIGNAL BIPOLAR PULSE RESPONSE 1.6 1.6 1.2 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1.2 AV = -1 SOIC 0.8 0.4 0 -0.4 AV = -1 SOIC 0.8 0.4 0 -0.4 -0.8 -0.8 -1.2 -1.2 -1.6 -1.6 TIME (5ns/DIV.) FIGURE 8. LARGE SIGNAL POSITIVE PULSE RESPONSE 7 TIME (5ns/DIV.) FIGURE 9. LARGE SIGNAL BIPOLAR PULSE RESPONSE HFA1405 Typical Performance Curves VSUPPLY = ±5V, TA = 25oC, RF = Value From the Optimum Feedback Resistor Table, RL = 100Ω, Unless Otherwise Specified (Continued) 1.6 160 AV = +6 SOIC OUTPUT VOLTAGE (V) 80 40 0 -40 0.8 0.4 0 -0.4 -80 -0.8 -120 -1.2 -1.6 -160 TIME (5ns/DIV.) TIME (5ns/DIV.) VOUT = 200mVP-P 6 SOIC 3 AV = +2 GAIN 0 AV = -1 -3 AV = +6 PHASE 0 90 AV = +6 180 AV = -1 AV = +2 270 360 0.3 1 10 100 NORMALIZED GAIN (dB) FIGURE 11. LARGE SIGNAL PULSE RESPONSE NORMALIZED PHASE (DEGREES) NORMALIZED GAIN (dB) FIGURE 10. SMALL SIGNAL PULSE RESPONSE 2 AV = +2 VOUT = 200mVP-P 1 SOIC 0 GAIN -1 RF = 1kΩ RF = 1.5kΩ -2 -3 90 180 270 RF = 500Ω 1 10 100 FREQUENCY (MHz) FREQUENCY (MHz) 360 800 FIGURE 13. FREQUENCY RESPONSE vs FEEDBACK RESISTOR 0.2 0.3 VOUT = 200mVP-P 0.2 AV = +2, SOIC VOUT = 200mVP-P 0.1 SOIC 0.1 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 0 RF = 1.5kΩ PHASE 800 FIGURE 12. FREQUENCY RESPONSE RF = 500Ω RF = 683Ω RF = 750Ω PHASE (DEGREES) OUTPUT VOLTAGE (mV) 120 AV = +6 SOIC 1.2 AV = -1 0 -0.1 AV = +2 -0.2 -0.3 -0.4 AV = +6 -0.5 RF = 500Ω 0 -0.1 RF = 683Ω -0.2 -0.3 RF = 750Ω -0.4 RF = 1kΩ -0.5 RF = 1.5kΩ -0.6 -0.7 -0.6 -0.7 -0.8 1 10 FREQUENCY (MHz) FIGURE 14. GAIN FLATNESS 8 100 1 10 FREQUENCY (MHz) 100 FIGURE 15. GAIN FLATNESS vs FEEDBACK RESISTOR HFA1405 Typical Performance Curves VSUPPLY = ±5V, TA = 25oC, RF = Value From the Optimum Feedback Resistor Table, RL = 100Ω, Unless Otherwise Specified (Continued) -10 AV = +2 VOUT = 2V SOIC 0.2 -20 SETTLING ERROR (%) CROSSTALK (dB) SOIC 0.15 -30 RL = 100Ω -40 -50 -60 RL = ∞ -70 -80 0.1 0.05 0.025 0 -0.025 -0.05 -0.1 -90 -0.15 -100 -0.2 -110 0.3 1 10 FREQUENCY (MHz) 100 200 0 1.6 AV = +2 PDIP 1.2 80 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (mV) 120 40 0 -40 25 30 TIME (ns) 35 40 45 AV = +2 PDIP 0 -0.4 -120 -1.2 -1.6 -160 TIME (5ns/DIV.) TIME (5ns/DIV.) FIGURE 18. SMALL SIGNAL PULSE RESPONSE FIGURE 19. LARGE SIGNAL PULSE RESPONSE 1.6 AV = -1 PDIP 1.2 80 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (mV) 20 0.4 -0.8 120 15 0.8 -80 160 10 FIGURE 17. SETTLING RESPONSE FIGURE 16. ALL HOSTILE CROSSTALK 160 5 40 0 -40 AV = -1 PDIP 0.8 0.4 0 -0.4 -80 -0.8 -120 -1.2 -1.6 -160 TIME (5ns/DIV.) FIGURE 20. SMALL SIGNAL PULSE RESPONSE 9 TIME (5ns/DIV.) FIGURE 21. LARGE SIGNAL PULSE RESPONSE 50 HFA1405 Typical Performance Curves VSUPPLY = ±5V, TA = 25oC, RF = Value From the Optimum Feedback Resistor Table, RL = 100Ω, Unless Otherwise Specified (Continued) 160 PDIP 1.2 80 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (mV) 120 1.6 AV = +1 40 0 -40 -80 AV = +1 PDIP 0.8 0.4 0 -0.4 -0.8 -1.2 -120 -1.6 -160 TIME (5ns/DIV.) TIME (5ns/DIV.) FIGURE 22. SMALL SIGNAL PULSE RESPONSE OUTPUT VOLTAGE (mV) 120 1.6 +6 AA VV==+2 PDIP PDIP RF = 150Ω 1.2 OUTPUT VOLTAGE (V) 160 FIGURE 23. LARGE SIGNAL PULSE RESPONSE 80 40 0 -40 AV = +6 PDIP RF = 150Ω 0.8 0.4 0 -0.4 -80 -0.8 -120 -1.2 -1.6 -160 TIME (5ns/DIV.) TIME (5ns/DIV.) FIGURE 24. SMALL SIGNAL PULSE RESPONSE FIGURE 25. LARGE SIGNAL PULSE RESPONSE 1.6 160 1.2 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (mV) 120 AV = +6 PDIP RF = 500Ω 80 40 0 -40 0.8 0.4 0 -0.4 -80 -0.8 -120 -1.2 -160 AV = +6 PDIP RF = 500Ω -1.6 TIME (5ns/DIV.) FIGURE 26. SMALL SIGNAL PULSE RESPONSE 10 TIME (5ns/DIV.) FIGURE 27. LARGE SIGNAL PULSE RESPONSE HFA1405 Typical Performance Curves VSUPPLY = ±5V, TA = 25oC, RF = Value From the Optimum Feedback Resistor Table, 3 AV = +2 GAIN 0 -3 PHASE AV = -1 AV = +1 (RF = +RS = 510Ω) 0 -6 90 AV = +2 AV = -1 AV = +1 180 270 360 0.3 1 10 100 AV = +6 VOUT = 200mVP-P 3 PDIP 0 GAIN RF = 150Ω RF = 500Ω -3 0 -6 PHASE 90 RF = 500Ω RF = 150Ω 180 270 360 1 0.3 800 10 100 PHASE (DEGREES) PDIP NORMALIZED GAIN (dB) VOUT = 200mVP-P NORMALIZED PHASE (DEGREES) NORMALIZED GAIN (dB) RL = 100Ω, Unless Otherwise Specified (Continued) 800 FREQUENCY (MHz) FREQUENCY (MHz) FIGURE 28. FREQUENCY RESPONSE FIGURE 29. FREQUENCY RESPONSE VOUT = 5VP-P 2 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 3 AV = -1 PDIP 1 0 AV = +2 -1 -2 -3 -4 AV = +2 2 RF = 390Ω VOUT = 200mVP-P 1 RF = 365Ω PDIP 0 -1 RF = 422Ω -2 RF = 510Ω -3 AV = +6 (RF = 500Ω) AV = +6 (RF = 150Ω) 0.3 1 10 100 1 800 10 PDIP AV = +1 (RF = +RS = 510Ω) -10 AV = +2 -20 -30 0 CROSSTALK (dB) NORMALIZED GAIN (dB) PDIP VOUT = 200mVP-P 0.1 800 FIGURE 31. FREQUENCY RESPONSE vs FEEDBACK RESISTOR FIGURE 30. FULL POWER BANDWIDTH 0.2 100 FREQUENCY (MHz) FREQUENCY (MHz) -0.1 -0.2 AV = +6 -0.3 AV = -1 (RF = 150Ω) -40 RL = 100Ω -50 RL = ∞ -60 -70 -80 -90 1 10 FREQUENCY (MHz) FIGURE 32. GAIN FLATNESS 11 100 -100 0.3 1 10 FREQUENCY (MHz) FIGURE 33. ALL HOSTILE CROSSTALK 100 HFA1405 Typical Performance Curves VSUPPLY = ±5V, TA = 25oC, RF = Value From the Optimum Feedback Resistor Table, RL = 100Ω, Unless Otherwise Specified (Continued) 3.6 0.2 PDIP 3.4 OUTPUT VOLTAGE (V) 3.5 0.1 0.05 0.025 0 -0.025 -0.05 -0.1 3.3 AV = -1 +VOUT (RL= 100Ω) |-VOUT| (RL= 100Ω) |-VOUT| (RL= 50Ω) 3.2 3.1 +VOUT (RL= 50Ω) 3.0 2.9 2.8 -0.15 2.7 -0.2 0 5 10 15 20 25 30 TIME (ns) 35 40 45 2.6 -50 50 -25 0 25 6.5 6.4 6.3 6.2 6.1 6.0 5.9 5.8 5.7 5.6 5 5.5 6 6.5 SUPPLY VOLTAGE (±V) FIGURE 36. SUPPLY CURRENT vs SUPPLY VOLTAGE 12 75 100 FIGURE 35. OUTPUT VOLTAGE vs TEMPERATURE 6.6 5.5 4.5 50 TEMPERATURE (oC) FIGURE 34. SETTLING RESPONSE SUPPLY CURRENT (mA/AMPLIFIER) SETTLING ERROR (%) 0.15 AV = +2 VOUT = 2V 7 125 HFA1405 Die Characteristics DIE DIMENSIONS: SUBSTRATE POTENTIAL (POWERED UP): 79 mils x 118 mils Floating (Recommend Connection to V-) 2000µm x 3000µm PASSIVATION: Type: Nitride Thickness: 4kÅ ± 0.5kÅ METALLIZATION: Type: Metal 1: AICu (2%)/TiW Thickness: Metal 1: 8kÅ ± 0.4kÅ TRANSISTOR COUNT: 320 Type: Metal 2: AICu (2%) Thickness: Metal 2: 16kÅ ± 0.8kÅ Metallization Mask Layout HFA1405 -IN1 OUT1 OUT4 -IN4 +IN4 +IN1 V+ V- +IN3 +IN2 -IN2 13 OUT2 V- OUT3 -IN3 HFA1405 Small Outline Plastic Packages (SOIC) M14.15 (JEDEC MS-012-AB ISSUE C) N INDEX AREA 0.25(0.010) M H 14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M E INCHES -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- µα e A1 B 0.25(0.010) M C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.3367 0.3444 8.55 8.75 3 E 0.1497 0.1574 3.80 4.00 4 e C 0.10(0.004) B S 0.050 BSC 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 14 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N NOTES: MILLIMETERS α 14 0o 14 8o 0o 7 8o Rev. 0 12/93 HFA1405 Dual-In-Line Plastic Packages (PDIP) E14.3 (JEDEC MS-001-AA ISSUE D) N 14 LEAD DUAL-IN-LINE PLASTIC PACKAGE E1 INDEX AREA 1 2 3 INCHES N/2 -B- -AD E BASE PLANE -C- A2 SEATING PLANE A L D1 e B1 D1 A1 eC B 0.010 (0.25) M C A B S MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A - 0.210 - 5.33 4 A1 0.015 - 0.39 - 4 A2 0.115 0.195 2.93 4.95 - B 0.014 0.022 0.356 0.558 - C L B1 0.045 0.070 1.15 1.77 8 eA C 0.008 0.014 C D 0.735 0.775 18.66 eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 0.204 0.355 19.68 5 D1 0.005 - 0.13 - 5 E 0.300 0.325 7.62 8.25 6 E1 0.240 0.280 6.10 7.11 5 e 0.100 BSC 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. eA 0.300 BSC 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. eB - L 0.115 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. N 2.54 BSC 7.62 BSC 0.430 - 0.150 2.93 14 10.92 3.81 14 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 6 7 4 9 Rev. 0 12/93 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 1.14mm). All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15