NTST40120CT D

NTST40120CT,
NTSJ40120CTG,
NTSB40120CT-1G,
NTSB40120CTG,
NTSB40120CTT4G
Very Low Forward Voltage
Trench-based Schottky
Rectifier
Exceptionally Low VF = 0.43 V at IF = 5 A
http://onsemi.com
VERY LOW FORWARD
VOLTAGE, LOW LEAKAGE
SCHOTTKY BARRIER
RECTIFIERS 40 AMPERES,
120 VOLTS
Features
• Fine Lithography Trench−based Schottky Technology for Very Low
•
•
•
•
•
•
PIN CONNECTIONS
Forward Voltage and Low Leakage
Fast Switching with Exceptional Temperature Stability
Low Power Loss and Lower Operating Temperature
Higher Efficiency for Achieving Regulatory Compliance
Low Thermal Resistance
High Surge Capability
Pb−Free and Halide−Free Packages are Available
1
2, 4
3
4
4
Typical Applications
• Switching Power Supplies including Notebook/Netbook Adapters,
•
•
•
•
ATX and Flat Panel Display
High Frequency and DC−DC Converters
Freewheeling and OR−ing Diodes
Reverse Battery Protection
Instrumentation
1
2
12
3
TO−220
CASE 221A
STYLE 6
3
I2PAK
CASE 418D
STYLE 3
Mechanical Characteristics
• Case: Epoxy, Molded
• Epoxy Meets Flammability Rating UL 94−0 @ 0.125 in
• Finish: All External Surfaces Corrosion Resistant and Terminal
4
Leads are Readily Solderable
• Lead Temperature for Soldering Purposes: 260°C Maximum for
10 sec
1
2
3
TO−220FP
CASE 221AH
D2PAK
CASE 418B
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 5 of this data sheet.
© Semiconductor Components Industries, LLC, 2014
September, 2014 − Rev. 6
1
Publication Order Number:
NTST40120CT/D
NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG,
NTSB40120CTT4G
MAXIMUM RATINGS
Rating
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
Average Rectified Forward Current
(Rated VR, TC = 120°C)
Symbol
Value
Unit
VRRM
VRWM
VR
120
V
IF(AV)
A
Per Device
Per Diode
Peak Repetitive Forward Current
(Rated VR, Square Wave, 20 kHz, TC = 125°C)
40
20
IFRM
A
Per Device
Per Diode
Nonrepetitive Peak Surge Current
(Surge applied at rated load conditions halfwave, single phase, 60 Hz)
80
40
IFSM
250
A
TJ
−40 to +150
°C
Storage Temperature
Tstg
−40 to +150
°C
Voltage Rate of Change (Rated VR)
dv/dt
10,000
V/ms
Operating Junction Temperature
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
THERMAL CHARACTERISTICS
Rating
Maximum Thermal Resistance per Diode
Junction−to−Case
Junction−to−Ambient
Symbol
NTST40120CTG,
NTSB40120CT−1G
NTSB40120CTG
NTSJ40120CTG
Unit
RqJC
RqJA
1.3
70
0.79
46.3
4.0
105
°C/W
°C/W
ELECTRICAL CHARACTERISTICS (Per Leg unless otherwise noted)
Rating
Symbol
Maximum Instantaneous Forward Voltage (Note 1)
(IF = 5 A, TJ = 25°C)
(IF = 10 A, TJ = 25°C)
(IF = 20 A, TJ = 25°C)
Typ
Max
0.50
0.60
0.78
−
−
0.91
0.43
0.53
0.63
−
−
0.71
16
16
−
−
mA
mA
−
30
500
100
mA
mA
vF
(IF = 5 A, TJ = 125°C)
(IF = 10 A, TJ = 125°C)
(IF = 20 A, TJ = 125°C)
Maximum Instantaneous Reverse Current (Note 1)
(VR = 90 V, TJ = 25°C)
(VR = 90 V, TJ = 125°C)
V
IR
(Rated dc Voltage, TJ = 25°C)
(Rated dc Voltage, TJ = 125°C)
Unit
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
1. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%
http://onsemi.com
2
NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG,
NTSB40120CTT4G
100
100
TA = 150°C
TA = 150°C
I R , REVERSE CURRENT (mA)
i F , INSTANTANEOUS FORWARD CURRENT (AMPS)
TYPICAL CHARACTERISITICS
TA = 25°C
10
TA = 125°C
1.0
0.1
10
TA = 125°C
1.0
0.1
0.01
TA = 25°C
0.001
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
vF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS)
20
CJ, JUNCTION CAPACITANCE (pF)
10000
TJ = 25°C
120
1000
1
10
VR, REVERSE VOLTAGE (VOLTS)
100
40
RqJC = 1.3°C/W
35
dc
30
25
20
SQUARE WAVE
15
10
5
0
0
20
Figure 3. Typical Junction Capacitance
40
60
80
100
120
TC, CASE TEMPERATURE (°C)
140
Figure 4. Current Derating per Leg
18
80
75
70
65
60
55
50
45
40
35
30
25
20
15
10
5
0
RqJC = 1.3°C/W
dc
SQUARE WAVE
PF(AV), AVERAGE FORWARD POWER DISSIPATION (W)
IF(AV), AVERAGE FORWARD CURRENT (A)
110
Figure 2. Typical Reverse Current
IF(AV), AVERAGE FORWARD CURRENT (A)
Figure 1. Typical Forward Voltage
100
0.1
50
70
90 100
40
60
80
VR, REVERSE VOLTAGE (VOLTS)
30
IPK/IAV = 5
16
SQUARE
WAVE
14
IPK/IAV = 10
10
IPK/IAV = 20
8
6
4
2
TA = 150°C
0
0
20
40
60
80
100
120
TC, CASE TEMPERATURE (°C)
0
140
dc
12
2
4
6
8
10
12
14
16 18
20
IF(AV), AVERAGE FORWARD CURRENT (A)
Figure 5. Current Derating, Case
Figure 6. Forward Power Dissipation
http://onsemi.com
3
22 24
NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG,
NTSB40120CTT4G
TYPICAL CHARACTERISITICS
R(t), TYPICAL TRANSIENT THERMAL
RESISTANCE (°C/W)
10
1
50% Duty Cycle
20%
10%
0.1
5%
2%
Single Pulse
1%
0.01
0.000001
0.00001
0.0001
0.001
0.01
0.1
t, Pulse Time (sec)
1
10
100
1000
Figure 7. Typical Transient Thermal Response for NTST40120CT and NTSB40120CT−1G
R(t), TYPICAL TRANSIENT THERMAL
RESISTANCE (°C/W)
10
50% Duty Cycle
1
20%
0.1
10%
5%
2%
1%
0.01
Single Pulse
0.001
0.000001
0.00001
0.0001
0.001
0.01
0.1
1
10
100
1000
100
1000
t, Pulse Time (sec)
R(t), TYPICAL TRANSIENT THERMAL
RESISTANCE (°C/W)
Figure 8. Typical Transient Thermal Response for NTSJ40120CTG
1
50% Duty Cycle
0.1
20%
10%
5%
2%
1%
0.01
0.000001
Single Pulse
0.00001
0.0001
0.001
0.01
0.1
t, Pulse Time (sec)
1
10
Figure 9. Typical Transient Thermal Response for NTSB40120CTG
http://onsemi.com
4
NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG,
NTSB40120CTT4G
ORDERING INFORMATION
Package
Shipping†
NTST40120CTG
TO−220
(Pb−Free)
50 Units / Rail
NTST40120CTH
TO−220
(Pb−Free and Halide−Free)
50 Units / Rail
NTSJ40120CTG
TO−220FP
(Pb−Free and Halide−Free)
50 Units / Rail
NTSB40120CT−1G
I2PAK
(Pb−Free)
50 Units / Rail
NTSB40120CTG
D2PAK
(Pb−Free)
50 Units / Rail
NTSB40120CTT4G
D2PAK
(Pb−Free)
800 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MARKING DIAGRAMS
AYWW
TS40120Cx
AKA
AYWW
TS40120CG
AKA
AYWW
TS40120CG
AKA
TO−220
TO−220FP
I2PAK
A
Y
WW
AKA
x
G
H
= Assembly Location
= Year
= Work Week
= Polarity Designator
= G or H
= Pb−Free Package
= Halide−Free Package
http://onsemi.com
5
AYWW
TS40120CG
AKA
D2PAK
NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG,
NTSB40120CTT4G
PACKAGE DIMENSIONS
TO−220
CASE 221A−09
ISSUE AH
−T−
B
SEATING
PLANE
C
F
T
S
4
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
A
Q
1 2 3
U
H
K
Z
L
R
V
J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
G
D
INCHES
MIN
MAX
0.570
0.620
0.380
0.415
0.160
0.190
0.025
0.038
0.142
0.161
0.095
0.105
0.110
0.161
0.014
0.024
0.500
0.562
0.045
0.060
0.190
0.210
0.100
0.120
0.080
0.110
0.045
0.055
0.235
0.255
0.000
0.050
0.045
----0.080
MILLIMETERS
MIN
MAX
14.48
15.75
9.66
10.53
4.07
4.83
0.64
0.96
3.61
4.09
2.42
2.66
2.80
4.10
0.36
0.61
12.70
14.27
1.15
1.52
4.83
5.33
2.54
3.04
2.04
2.79
1.15
1.39
5.97
6.47
0.00
1.27
1.15
----2.04
N
STYLE 6:
PIN 1.
2.
3.
4.
ANODE
CATHODE
ANODE
CATHODE
I2PAK (TO−262)
CASE 418D
ISSUE D
C
E
V
−B−
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
4
A
W
1
2
DIM
A
B
C
D
E
F
G
H
J
K
S
V
W
3
F
−T−
SEATING
PLANE
K
S
J
G
D 3 PL
0.13 (0.005) M T B
H
M
http://onsemi.com
6
INCHES
MIN
MAX
0.335
0.380
0.380
0.406
0.160
0.185
0.026
0.035
0.045
0.055
0.122 REF
0.100 BSC
0.094
0.110
0.013
0.025
0.500
0.562
0.390 REF
0.045
0.070
0.522
0.551
STYLE 3:
PIN 1.
2.
3.
4.
ANODE
CATHODE
ANODE
CATHODE
MILLIMETERS
MIN
MAX
8.51
9.65
9.65
10.31
4.06
4.70
0.66
0.89
1.14
1.40
3.10 REF
2.54 BSC
2.39
2.79
0.33
0.64
12.70
14.27
9.90 REF
1.14
1.78
13.25
14.00
NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG,
NTSB40120CTT4G
PACKAGE DIMENSIONS
TO−220 FULLPACK, 3−LEAD
CASE 221AH
ISSUE F
A
B
E
A
P
E/2
0.14
Q
D
M
B A
H1
M
A1
C
NOTE 3
1 2 3
L
L1
3X
3X
c
b
b2
0.25
M
B A
M
C
A2
e
SIDE VIEW
FRONT VIEW
SECTION D−D
A
NOTE 6
NOTE 6
H1
D
SEATING
PLANE
D
A
SECTION A−A
ALTERNATE CONSTRUCTION
http://onsemi.com
7
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. CONTOUR UNCONTROLLED IN THIS AREA.
4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH AND GATE
PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO
EXCEED 0.13 PER SIDE. THESE DIMENSIONS ARE TO BE
MEASURED AT OUTERMOST EXTREME OF THE PLASTIC BODY.
5. DIMENSION b2 DOES NOT INCLUDE DAMBAR PROTRUSION.
LEAD WIDTH INCLUDING PROTRUSION SHALL NOT EXCEED 2.00.
6. CONTOURS AND FEATURES OF THE MOLDED PACKAGE BODY
MAY VARY WITHIN THE ENVELOP DEFINED BY DIMENSIONS A1
AND H1 FOR MANUFACTURING PURPOSES.
DIM
A
A1
A2
b
b2
c
D
E
e
H1
L
L1
P
Q
MILLIMETERS
MIN
MAX
4.30
4.70
2.50
2.90
2.50
2.90
0.54
0.84
1.10
1.40
0.49
0.79
14.70
15.30
9.70
10.30
2.54 BSC
6.60
7.10
12.50
14.73
--2.80
3.00
3.40
2.80
3.20
NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG,
NTSB40120CTT4G
PACKAGE DIMENSIONS
D2PAK 3
CASE 418B−04
ISSUE K
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 418B−01 THRU 418B−03 OBSOLETE,
NEW STANDARD 418B−04.
C
E
V
W
−B−
4
DIM
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
S
V
A
1
2
S
3
−T−
SEATING
PLANE
K
W
J
G
D 3 PL
0.13 (0.005)
H
M
T B
M
VARIABLE
CONFIGURATION
ZONE
N
R
MILLIMETERS
MIN
MAX
8.64
9.65
9.65 10.29
4.06
4.83
0.51
0.89
1.14
1.40
7.87
8.89
2.54 BSC
2.03
2.79
0.46
0.64
2.29
2.79
1.32
1.83
7.11
8.13
5.00 REF
2.00 REF
0.99 REF
14.60 15.88
1.14
1.40
P
U
L
M
INCHES
MIN
MAX
0.340 0.380
0.380 0.405
0.160 0.190
0.020 0.035
0.045 0.055
0.310 0.350
0.100 BSC
0.080
0.110
0.018 0.025
0.090
0.110
0.052 0.072
0.280 0.320
0.197 REF
0.079 REF
0.039 REF
0.575 0.625
0.045 0.055
L
M
L
M
F
F
F
VIEW W−W
1
VIEW W−W
2
VIEW W−W
3
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
8
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NTST40120CT/D