LTC3115-1 40V, 2A Synchronous Buck-Boost DC/DC Converter Features n n n n n n n n n n n n n n Description Wide VIN Range: 2.7V to 40V Wide VOUT Range: 2.7V to 40V 1A Output Current for VIN ≥ 3.6V, VOUT = 5V 2A Output Current in Step-Down Operation for VIN ≥ 6V Programmable Frequency: 100kHz to 2MHz Synchronizable Up to 2MHz with an External Clock Up to 95% Efficiency 30µA No-Load Quiescent Current in Burst Mode® Operation Ultralow Noise Buck-Boost PWM Internal Soft-Start 3µA Supply Current in Shutdown Programmable Input Undervoltage Lockout Small 4mm × 5mm × 0.75mm DFN Package Thermally Enhanced 20-Lead TSSOP Package The LTC®3115-1 is a high voltage monolithic synchronous buck-boost DC/DC converter. Its wide 2.7V to 40V input and output voltage ranges make it well suited to a wide variety of automotive and industrial applications. A proprietary low noise switching algorithm optimizes efficiency with input voltages that are above, below or even equal to the output voltage and ensures seamless transitions between operational modes. Programmable frequency PWM mode operation provides low noise, high efficiency operation and the ability to synchronize switching to an external clock. Switching frequencies up to 2MHz are supported to allow use of small value inductors for miniaturization of the application circuit. Pin selectable Burst Mode operation reduces standby current and improves light load efficiency which, combined with a 3µA shutdown current, make the LTC3115-1 ideally suited for battery-powered applications. Additional features include output disconnect in shutdown, short-circuit protection and internal soft-start. The LTC3115-1 is available in thermally enhanced 16-lead 4mm × 5mm × 0.75mm DFN and 20‑lead TSSOP packages. Applications n n n n n 24V/28V Industrial Applications Automotive Power Systems Telecom, Servers and Networking Equipment FireWire Regulator Multiple Power Source Supplies L, LT, LTC, LTM, Burst Mode, LTspice, Linear Technology and the Linear logo are registered trademarks and No RSENSE is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 6404251, 6166527 and others pending. Typical Application Efficiency vs VIN 10µH 95 2.7V TO 40V BST1 SW1 4.7µF BURST PWM OFF ON PVIN VIN SW2 BST2 PVOUT PWM/SYNC VC RUN FB 60.4k 3300pF PGND 1M 33pF 15k PVCC VCC GND 5V 1A VIN > 3.6V 2A VIN ≥ 6V 47µF LTC3115-1 RT 47.5k ILOAD = 0.5A 0.1µF 249k 4.7µF 90 EFFICIENCY (%) 0.1µF ILOAD = 1A 85 80 75 (OPTIONAL) 3115 TA01a 70 VOUT = 5V 2 10 INPUT VOLTAGE (V) 40 31151 TA01b 31151fb For more information www.linear.com/LTC3115-1 1 LTC3115-1 Absolute Maximum Ratings (Note 1) VIN, PVIN, PVOUT......................................... –0.3V to 45V VSW1 DC............................................ –0.3V to (PVIN + 0.3V) Pulsed (<100ns).......................–1.5V to (PVIN + 1.5V) VSW2 DC..........................................–0.3V to (PVOUT + 0.3V) Pulsed (<100ns)..................... –1.5V to (PVOUT + 1.5V) VRUN.............................................. –0.3V to (VIN + 0.3V) VBST1......................................VSW1 – 0.3V to VSW1 + 6V VBST2......................................VSW2 – 0.3V to VSW2 + 6V VPWM/SYNC.................................................... –0.3V to 6V Voltage, All Other Pins.................................. –0.3V to 6V Operating Junction Temperature Range (Notes 2, 4) LTC3115E-1/LTC3115I-1...................... –40°C to 125°C LTC3115H-1........................................ –40°C to 150°C LTC3115MP-1...................................... –55°C to 150°C Storage Temperature Range................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) FE...................................................................... 300°C Pin Configuration TOP VIEW TOP VIEW RUN 1 16 PWM/SYNC SW2 2 15 SW1 PVOUT 3 14 PVIN GND 4 GND 5 VC 6 11 PVCC FB 7 10 VIN RT 8 9 PGND 17 PGND 1 20 PGND RUN 2 19 PWM/SYNC SW2 3 18 SW1 PVOUT 4 17 PVIN GND 5 GND 6 VC 7 14 PVCC FB 8 13 VIN RT 9 12 VCC 13 BST1 12 BST2 VCC 21 PGND PGND 10 DHD PACKAGE 16-LEAD (5mm × 4mm) PLASTIC DFN TJMAX = 125°C, θJA = 43°C/W, θJC = 4.3°C/W EXPOSED PAD (PIN 17) IS PGND, MUST BE SOLDERED TO PCB 16 BST1 15 BST2 11 PGND FE PACKAGE 20-LEAD PLASTIC TSSOP TJMAX = 150°C, θJA = 38°C/W, θJC = 10°C/W EXPOSED PAD (PIN 21) IS PGND, MUST BE SOLDERED TO PCB FOR RATED THERMAL PERFORMANCE Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3115EDHD-1#PBF LTC3115EDHD-1#TRPBF 31151 16-Lead (5mm × 4mm) Plastic DFN –40°C to 125°C LTC3115IDHD-1#PBF LTC3115IDHD-1#TRPBF 31151 16-Lead (5mm × 4mm) Plastic DFN –40°C to 125°C LTC3115EFE-1#PBF LTC3115EFE-1#TRPBF LTC3115FE-1 20-Lead Plastic TSSOP –40°C to 125°C LTC3115IFE-1#PBF LTC3115IFE-1#TRPBF LTC3115FE-1 20-Lead Plastic TSSOP –40°C to 125°C LTC3115HFE-1#PBF LTC3115HFE-1#TRPBF LTC3115FE-1 20-Lead Plastic TSSOP –40°C to 150°C LTC3115MPFE-1#PBF LTC3115MPFE-1#TRPBF LTC3115FE-1 20-Lead Plastic TSSOP –55°C to 150°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 2 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are for TA = 25°C (Note 2). PVIN = VIN = 24V, PVOUT = 5V, unless otherwise noted. PARAMETER Input Operating Voltage Output Operating Voltage Input Undervoltage Lockout Threshold Input Undervoltage Lockout Hysteresis VCC Undervoltage Lockout Threshold VCC Undervoltage Lockout Hysteresis Input Current in Shutdown Input Quiescent Current in Burst Mode Operation Oscillator Frequency Oscillator Operating Frequency PWM/SYNC Clock Input Frequency PWM/SYNC Input Logic Threshold Soft-Start Duration Feedback Voltage Feedback Voltage Line Regulation Feedback Pin Input Current RUN Pin Input Logic Threshold RUN Pin Comparator Threshold RUN Pin Hysteresis Current RUN Pin Hysteresis Voltage Inductor Current Limit Reverse Inductor Current Limit Burst Mode Inductor Current Limit Maximum Duty Cycle Minimum Duty Cycle SW1, SW2 Minimum Low Time N-Channel Switch Resistance N-Channel Switch Leakage PVCC/VCC External Forcing Voltage VCC Regulation Voltage VCC Load Regulation VCC Line Regulation VCC Current Limit VCC Dropout Voltage VCC Reverse Current CONDITIONS l l VIN Falling VIN Rising VIN Rising (0°C to 125°C) MIN 2.7 2.7 2.4 2.6 l l VCC Falling l VRUN = 0V VFB = 1.1V (Not Switching), VPWM/SYNC = Low RT = 35.7k, VPWM/SYNC = High VPWM/SYNC = High l 900 100 100 0.5 l 977 l l l l VIN = 2.7V to 40V VRUN Rising l 0.3 1.16 (Note 3) Current into PVOUT (Note 3) (Note 3) Percentage of Period SW2 is Low in Boost Mode, RT = 35.7k (Note 5) Percentage of Period SW1 is High in Buck Mode, RT = 35.7k (Note 5) RT = 35.7k (Note 5) Switch A (From PVIN to SW1) Switch B (From SW1 to PGND) Switch C (From SW2 to PGND) Switch D (From PVOUT to SW2) PVIN = PVOUT = 40V l 2.4 l 0.65 90 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3115-1 is tested under pulsed load conditions such that TJ ≈ TA. The LTC3115E-1 is guaranteed to meet specifications from 0°C to 85°C junction temperature. Specifications over the –40°C 100 2.4 200 3 50 1000 1.0 9 1000 0.1 1 0.8 1.21 500 100 3.0 1.5 1.0 95 MAX 40 40 2.7 2.8 2.725 2.6 10 1100 2000 2000 1.5 1017 50 1.1 1.26 3.7 1.35 0 l 100 150 150 150 150 0.1 4.58 4.33 IVCC = 1mA IVCC = 1mA to 20mA IVCC = 1mA, VIN = 5V to 40V VCC = 2.5V IVCC = 5mA, VIN = 2.7V VCC = 5V, VIN = 3.6V TYP 50 4.45 1.2 0.5 110 50 10 10 5.5 4.58 UNITS V V V V V mV V mV µA µA kHz kHz kHz V ms mV % nA V V nA mV A A A % % ns mΩ mΩ mΩ mΩ µA V V % % mA mV µA to 125°C operating junction temperature range are ensured by design, characterization and correlation with statistical process controls. The LTC3115I-1 specifications are guaranteed over the –40°C to 125°C operating junction temperature range. The LTC3115H-1 specifications are guaranteed over the –40°C to 150°C operating junction temperature range. The LTC3115MP-1 specifications are guaranteed over the –55°C to 150°C operating junction temperature range. High junction temperatures degrade 31151fb For more information www.linear.com/LTC3115-1 3 LTC3115-1 Electrical Characteristics operating lifetime; operating lifetime is derated for junction temperatures greater than 125°C. The maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal resistance and other environmental factors. The junction temperature (TJ in °C) is calculated from the ambient temperature (TA in °C) and power dissipation (PD in Watts) according to the following formula: TJ = TA + (PD • θJA) where θJA is the thermal impedance of the package. Note 3: Current measurements are performed when the LTC3115-1 is not switching. The current limit values measured in operation will be somewhat higher due to the propagation delay of the comparators. Note 4: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. The maximum rated junction temperature will be exceeded when this protection is active. Continuous operation above the specified absolute maximum operating junction temperature may impair device reliability or permanently damage the device. Note 5: Switch timing measurements are made in an open-loop test configuration. Timing in the application may vary somewhat from these values due to differences in the switch pin voltage during the non-overlap durations when switch pin voltage is influenced by the magnitude and direction of the inductor current. Typical Performance Characteristics (TA = 25°C unless otherwise specified) PWM Mode Efficiency, VOUT = 5V, fSW = 500kHz, Non-Bootstrapped PWM Mode Efficiency, VOUT = 12V, fSW = 500kHz PWM Mode Efficiency, VOUT = 24V, fSW = 500kHz 100 100 90 90 90 80 80 70 60 50 VIN = 3.6V VIN = 5V VIN = 12V VIN = 24V VIN = 36V 40 30 20 0.01 0.10 LOAD CURRENT (A) EFFICIENCY (%) EFFICIENCY (%) 80 EFFICIENCY (%) 100 70 60 50 30 0.01 1 0.1 LOAD CURRENT (A) 31151 G01 60 50 VIN = 5V VIN = 12V VIN = 24V VIN = 36V 40 70 30 0.01 1 PWM Mode Efficiency, VOUT = 12V, fSW = 1MHz PWM Mode Efficiency, VOUT = 24V, fSW = 1MHz 100 90 90 90 80 80 VIN = 3.6V VIN = 5V VIN = 12V VIN = 24V VIN = 36V 40 30 20 0.01 0.1 LOAD CURRENT (A) 1 31151 G04 4 EFFICIENCY (%) EFFICIENCY (%) 50 EFFICIENCY (%) 100 80 70 60 50 VIN = 5V VIN = 12V VIN = 24V VIN = 36V 40 30 0.01 0.1 LOAD CURRENT (A) 1 31151 G03 100 60 0.1 LOAD CURRENT (A) 31151 G02 PWM Mode Efficiency, VOUT = 5V, fSW = 1MHz, Non-Bootstrapped 70 VIN = 12V VIN = 18V VIN = 24V VIN = 36V 40 1 31151 G05 70 60 50 VIN = 12V VIN = 18V VIN = 24V VIN = 36V 40 30 0.01 0.1 LOAD CURRENT (A) 1 31151 G06 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Typical Performance Characteristics Burst Mode Efficiency, VOUT = 12V, L = 15µH Burst Mode Efficiency, VOUT = 24V, L = 15µH 90 95 90 85 90 85 80 85 75 70 65 60 VIN = 3.6V VIN = 12V VIN = 24V VIN = 36V 55 50 0.1 1 10 LOAD CURRENT (mA) 80 80 EFFICIENCY (%) EFFICIENCY (%) EFFICIENCY (%) Burst Mode Efficiency, VOUT = 5V, L = 15µH, Non-Bootstrapped 75 70 65 55 50 0.1 100 1 10 LOAD CURRENT (mA) INPUT CURRENT (µA) 250 200 150 100 50 fSW = 1MHz 45 1 10 LOAD CURRENT (mA) 31151 G09 2.5 L = 22µH fSW = 500kHz 2.0 30 25 20 15 10 1.5 1.0 0.5 VOUT = 24V VOUT = 12V VOUT = 5V 5 10 INPUT VOLTAGE (V) 2 0 40 10 INPUT VOLTAGE (V) 2 0 40 2 40 10 INPUT VOLTAGE (V) 31151 G11 Maximum Load Current vs VIN, PWM Mode 2.5 100 Maximum Load Current vs VIN, PWM Mode 35 31151 G10 2.5 L = 15µH fSW = 1MHz Maximum Load Current vs VIN, PWM Mode 31151 G12 Maximum Load Current vs VIN, Burst Mode Operation 1000 L = 5.2µH fSW = 2MHz L = 22µH LOAD CURRENT (A) 1.5 1.0 0.5 10 INPUT VOLTAGE (V) 1.5 1.0 100 0.5 VOUT = 24V VOUT = 12V VOUT = 5V 2 LOAD CURRENT (mA) 2.0 2.0 0 50 0.1 100 VOUT = 24V VOUT = 12V VOUT = 5V 40 50 0 VIN = 12V VIN = 18V VIN = 24V VIN = 36V 55 LOAD CURRENT (A) VOUT = 24V VOUT = 15V VOUT = 5V VOUT = 5V, BOOTSTRAPPED 300 65 PWM Mode No-Load Input Current vs VIN Burst Mode No-Load Input Current vs VIN 350 70 31151 G08 INPUT CURRENT (mA) 400 75 60 VIN = 5V VIN = 12V VIN = 24V VIN = 36V 60 31151 G07 LOAD CURRENT (A) (TA = 25°C unless otherwise specified) 40 31151 G47 0 VOUT = 12V VOUT = 5V 2 10 INPUT VOLTAGE (V) 40 31151 G48 10 VOUT = 32V VOUT = 12V VOUT = 5V 2 10 INPUT VOLTAGE (V) 40 31151 G13 31151fb For more information www.linear.com/LTC3115-1 5 LTC3115-1 Typical Performance Characteristics NON-BOOTSTRAPPED 75 70 16 30 14 25 VIN = 36V VOUT = 24V 20 VIN = 12V VOUT = 5V 15 10 0 1000 500 1500 SWITCHING FREQUENCY (kHz) 0 2000 11.7 11.6 11.5 11.4 11.3 11.2 11.1 11.0 –50 0 50 100 TEMPERATURE (°C) CHANGE IN VOLTAGE FROM ZERO LOAD (%) VCC/PVCC CURRENT (mA) 11.8 150 0 500 1000 4 0.5 0.4 0.3 0.2 0.1 0 –0.2 –0.4 –0.6 –0.8 –1.0 –50 0 50 100 TEMPERATURE (°C) 150 31151 G20 5.5 Output Voltage Line Regulation 0.5 0.4 0.3 0.2 0.1 0 –0.3 –0.3 –0.4 –0.4 –0.5 5 31151 G16 0 2 1 0.5 1.5 LOAD CURRENT (A) –0.5 0 10 40 20 30 INPUT VOLTAGE (V) 31151 G19 VCC Regulator Load Regulation 1.0 VCC Regulator Line Regulation 0.8 –0.5 CHANGE FROM VIN = 24V (%) CHANGE IN VOLTAGE FROM ICC = 0mA (%) 0 4.5 4 VCC (V) –0.2 –0.2 0 0.4 3.5 –0.1 –0.1 VCC Voltage vs Temperature 0.2 3 31151 G18 1.0 0.6 0 2.5 2000 1500 SWITCHING FREQUENCY (kHz) 31151 G17 0.8 fSW = 500kHz 6 2 Output Voltage Load Regulation VIN = 6V VOUT = 5V fSW = 1MHz 11.9 CHANGE FROM 25°C (%) 8 31151 G15 Combined VCC/PVCC Supply Current vs Temperature 12.0 fSW = 1MHz 10 5 31151 G14 6 12 VCC/PVCC CURRENT (mA) 80 35 CHANGE IN OUTPUT VOLTAGE FROM VIN = 20V (%) EFFICIENCY (%) 85 VCC/PVCC CURRENT (mA) BOOTSTRAPPED 90 PWM MODE L = 47µH VIN = 24V VOUT = 5V ILOAD = 0.5A Combined VCC/PVCC Supply Current vs VCC Combined VCC/PVCC Supply Current vs Switching Frequency Efficiency vs Switching Frequency 95 (TA = 25°C unless otherwise specified) –1.0 0.6 0.4 0.2 0 –0.2 –1.5 –0.4 –0.6 –2.0 –0.8 –2.5 0 10 30 20 ICC (mA) 40 50 31151 G21 –1.0 0 10 20 30 INPUT VOLTAGE (V) 40 31151 G22 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Typical Performance Characteristics (TA = 25°C unless otherwise specified) VCC Regulator Dropout Voltage vs Temperature 0.25 1.0 VIN = 4V IVCC = 20mA 2.0 0.8 1.5 CHANGE FROM 25°C (%) 0.15 0.10 0.05 1.0 CHANGE FROM 25°C (%) 0.6 0.20 DROPOUT VOLTAGE (V) RUN Pin Hysteresis Current vs Temperature RUN Pin Threshold vs Temperature 0.4 0.2 0 –0.2 –0.4 0.5 0 –0.5 –1.0 –0.6 –1.5 –0.8 0 –50 0 50 100 TEMPERATURE (°C) –1.0 –50 150 0 –2.0 –50 150 50 100 TEMPERATURE (°C) 2.0 10000 Oscillator Frequency vs VIN 2.0 fSW = 1MHz 1.0 0.5 0 –0.5 –1.0 0 50 5 4 3 2 1 0 40 31151 G29 10 VIN (V) 300 VRUN = 0V 2.5 2.0 1.5 1.0 0.5 0 0 10 40 Power Switch Resistance vs Temperature POWER SWITCH (A-D) RESISTANCE (mΩ) COMBINED VIN/PVIN CURRENT (µA) CURRENT INTO RUN PIN (µA) 6 2 31151 G28 Shutdown Current on VIN/PVIN vs Input Voltage 3.0 20 10 30 RUN PIN VOLTAGE (V) –2.0 150 100 TEMPERATURE (°C) 31151 G27 VIN = 40V 0 0 –1.5 –2.0 –50 RUN Pin Current vs RUN Pin Voltage –1 0.5 –1.0 31151 G26 7 1.0 –0.5 –1.5 1000 fSW = 1MHz 1.5 CHANGE FROM VIN = 24V (%) CHANGE FROM 25°C (%) SWITCHING FREQUENCY (kHz) 1.5 100 RT (kΩ) 150 31151 G25 Oscillator Frequency vs Temperature Oscillator Frequency vs RT 100 10 50 100 TEMPERATURE (°C) 31151 G24 31151 G23 1000 0 20 30 INPUT VOLTAGE (V) 40 31151 G30 250 200 150 100 50 0 –50 0 50 100 TEMPERATURE (°C) 150 31151 G31 31151fb For more information www.linear.com/LTC3115-1 7 LTC3115-1 Typical Performance Characteristics Power Switch Resistance vs VCC 160 155 150 3.5 4 VCC (V) 4.5 5 5.5 5 0.8 4 0.6 3 0.4 0.2 0 –0.2 –0.4 –0.6 145 3 1.0 CHANGE FROM 25°C (%) CHANGE FROM 25°C (%) POWER SWITCH (A-D) RESISTANCE (mΩ) 165 2.5 Inductor Current Limit Thresholds vs Temperature FB Voltage vs Temperature 170 140 (TA = 25°C unless otherwise specified) –4 0 150 50 100 TEMPERATURE (°C) SW1, SW2 Minimum Low Time vs Switching Frequency SW1, SW2 Minimum Low Time vs VCC 200 180 98 96 94 fSW = 300kHz MINIMUM LOW TIME (ns) MINIMUM LOW TIME (ns) MINIMUM LOW TIME (ns) 100 140 120 fSW = 1MHz 100 fSW = 2MHz 80 50 100 TEMPERATURE (°C) 60 150 2.5 3.5 3 4 VCC (V) 4.5 MAXIMUM DUTY CYCLE (%) 95 94 93 92 91 1000 500 1500 SWITCHING FREQUENCY (kHz) 2000 31151 G38 8 VCC = 2.7V 120 100 VCC = 4.4V 60 5.5 0 500 1000 1500 SWITCHING FREQUENCY (kHz) 60 Die Temperature Rise vs Load Current, VOUT = 5V, fSW = 1.5MHz VIN = 36V VIN = 24V VIN = 12V VIN = 6V VIN = 3.6V 50 40 30 20 10 0 STANDARD DEMO PCB L = 15µH MSS1048 0 0.5 1 1.5 LOAD CURRENT (A) 2000 31151 G37 Die Temperature Rise vs Load Current, VOUT = 5V, fSW = 750kHz DIE TEMPERATURE CHANGE FROM AMBIENT (°C) SW2 Maximum Duty Cycle vs Switching Frequency 0 140 31151 G36 31151 G35 90 5 2 31151 G49 DIE TEMPERATURE CHANGE FROM AMBIENT (°C) 0 160 80 92 90 –50 150 50 100 TEMPERATURE (°C) 31151 G34 160 104 0 31151 G33 180 102 SWB CURRENT LIMIT –3 –5 –50 fSW = 1MHz NO LOAD 106 –2 –0.8 SW1, SW2 Minimum Low Time vs Temperature 108 0 –1 –1.0 –50 31151 G32 110 SWA CURRENT LIMIT 2 1 100 VIN = 36V VIN = 24V VIN = 12V VIN = 6V VIN = 3.6V 90 80 70 60 50 40 30 20 STANDARD DEMO PCB L = 15µH MSS1048 10 0 0 0.5 1 1.5 LOAD CURRENT (A) 2 31151 G50 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Typical Performance Characteristics (TA = 25°C unless otherwise specified) DIE TEMPERATURE CHANGE FROM AMBIENT (°C) Die Temperature Rise vs Load Current, VOUT = 12V, fSW = 750kHz 80 VIN = 36V VIN = 24V VIN = 12V VIN = 6V 70 60 Load Transient (0A to 1A), VIN = 24V, VOUT = 5V VOUT (200mV/DIV) VOUT (200mV/DIV) INDUCTOR CURRENT (1A/DIV) INDUCTOR CURRENT (2A/DIV) 40 30 FRONT PAGE APPLICATION 20 0 LOAD CURRENT (1A/DIV) LOAD CURRENT (1A/DIV) 50 10 Load Transient (0A to 1A), VIN = 3.6V, VOUT = 5V 200µs/DIV 31151 G39 FRONT PAGE APPLICATION 31151 G40 200µs/DIV STANDARD DEMO PCB L = 15µH MSS1048 0 0.5 1 1.5 LOAD CURRENT (A) 2 31151 G51 Output Voltage Ripple in Burst Mode Operation, VIN = 24V, VOUT = 5V Output Voltage Ripple in PWM Mode, VIN = 24V, VOUT = 5V Soft-Start Waveforms VRUN (5V/DIV) VOUT (50mV/DIV) INDUCTOR CURRENT (100mA/DIV) VCC (2V/DIV) INDUCTOR CURRENT (0.5A/DIV) L = 15µH COUT = 22µF ILOAD = 25mA 20µs/DIV 31151 G41 VOUT (2V/DIV) INDUCTOR CURRENT (1A/DIV) VOUT (5mV/DIV) FRONT PAGE APPLICATION Burst Mode Operation to PWM Mode Output Voltage Transient VPWM/SYNC (5V/DIV) VOUT (200mV/DIV) INDUCTOR CURRENT (1A/DIV) FRONT PAGE APPLICATION 500µs/DIV 31151 G44 2ms/DIV 31151 G42 L = 22µH COUT = 22µF ILOAD = 2A fSW = 750kHz Phase-Locked Loop Release, VIN = 24V, 1.2MHz Clock Phase-Locked Loop Acquisition, VIN = 24V 1.2MHz Clock VPWM/SYNC (5V/DIV) VPWM/SYNC (5V/DIV) VOUT (200mV/DIV) VOUT (200mV/DIV) INDUCTOR CURRENT (1A/DIV) INDUCTOR CURRENT (1A/DIV) FRONT PAGE APPLICATION 50µs/DIV 31151 G45 31151 G43 1µs/DIV FRONT PAGE APPLICATION 50µs/DIV 31151 G46 31151fb For more information www.linear.com/LTC3115-1 9 LTC3115-1 Pin Functions (DHD/FE) RUN (Pin 1/Pin 2): Input to Enable and Disable the IC and Set Custom Input UVLO Thresholds. The RUN pin can be driven by an external logic signal to enable and disable the IC. In addition, the voltage on this pin can be set by a resistor divider connected to the input voltage in order to provide an accurate undervoltage lockout threshold. The IC is enabled if RUN exceeds 1.21V nominally. Once enabled, a 0.5µA current is sourced by the RUN pin to provide hysteresis. To continuously enable the IC, this pin can be tied directly to the input voltage. The RUN pin cannot be forced more than 0.3V above VIN under any condition. SW2 (Pin 2/Pin 3): Buck-Boost Converter Power Switch Pin. This pin should be connected to one side of the buckboost inductor. PVOUT (Pin 3/Pin 4): Buck-Boost Converter Power Output. This pin should be connected to a low ESR capacitor with a value of at least 10µF. The capacitor should be placed as close to the IC as possible and should have a short return path to ground. In applications with VOUT > 20V that are subject to output overload or short-circuit conditions, it is recommended that a Schottky diode be installed from SW2 (anode) to PVOUT (cathode). In applications subject to output short circuits through an inductive load, it is recommended that a Schottky diode be installed from ground (anode) to PVOUT (cathode) to limit the extent that PVOUT is driven below ground during the short-circuit transient. GND (Pins 4, 5/Pins 5, 6): Signal Ground. These pins are the ground connections for the control circuitry of the IC and must be tied to ground in the application. VC (Pin 6/Pin 7): Error Amplifier Output. A frequency compensation network must be connected between this pin and FB to stabilize the voltage control loop. FB (Pin 7/Pin 8): Feedback Voltage Input. A resistor divider connected to this pin sets the output voltage for the buckboost converter. The nominal FB voltage is 1000mV. Care should be taken in the routing of connections to this pin in order to minimize stray coupling to the switch pin traces. RT (Pin 8/Pin 9): Oscillator Frequency Programming Pin. A resistor placed between this pin and ground sets the switching frequency of the buck-boost converter. 10 VCC (Pin 9/Pin 12): Low Voltage Supply Input for IC Control Circuitry. This pin powers internal IC control circuitry and must be connected to the PVCC pin in the application. A 4.7µF or larger bypass capacitor should be connected between this pin and ground. The VCC and PVCC pins must be connected together in the application. VIN (Pin 10/Pin 13): Power Supply Connection for Internal Circuitry and the VCC Regulator. This pin provides power to the internal VCC regulator and is the input voltage sense connection for the VIN divider. A 0.1µF bypass capacitor should be connected between this pin and ground. The bypass capacitor should be located as close to the IC as possible and should have a short return path to ground. PVCC (Pin 11/Pin 14): Internal VCC Regulator Output. This pin is the output pin of the internal linear regulator that generates the VCC rail from VIN. The PVCC pin is also the supply connection for the power switch gate drivers. If the trace connecting PVCC to VCC cannot be made short in length, an additional bypass capacitor should be connected between this pin and ground. The VCC and PVCC pins must be connected together in the application. BST2 (Pin 12/Pin 15): Flying Capacitor Pin for SW2. This pin must be connected to SW2 through a 0.1µF capacitor. This pin is used to generate the gate drive rail for power switch D. BST1 (Pin 13/Pin 16): Flying Capacitor Pin for SW1. This pin must be connected to SW1 through a 0.1µF capacitor. This pin is used to generate the gate drive rail for power switch A. PVIN (Pin 14/Pin 17): Power Input for the Buck-Boost Converter. A 4.7µF or larger bypass capacitor should be connected between this pin and ground. The bypass capacitor should be located as close to the IC as possible and should via directly down to the ground plane. When powered through long leads or from a high ESR power source, a larger bulk input capacitor (typically 47µF to 100µF) may be required. SW1 (Pin 15/Pin 18): Buck-Boost Converter Power Switch Pin. This pin should be connected to one side of the buckboost inductor. 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Pin Functions (DHD/FE) PWM/SYNC (Pin 16/Pin 19): Burst Mode/PWM Mode Control Pin and Synchronization Input. Forcing this pin high causes the IC to operate in fixed frequency PWM mode at all loads using the internal oscillator at the frequency set by the RT Pin. Forcing this pin low places the IC into Burst Mode operation for improved efficiency at light load and reduced standby current. If an external clock signal is connected to this pin, the buck-boost converter will synchronize its switching with the external clock using fixed frequency PWM mode operation. The pulse width (negative or positive) of the applied clock should be at least 100ns. The maximum operating voltage for the PWM/SYNC pin is 5.5V. The PWM/SYNC pin can be connected to VCC to force it high continuously. PGND (Exposed Pad Pin 17/Pins 1, 10, 11, 20, Exposed Pad Pin 21): Power Ground Connections. These pins should be connected to the power ground in the application. The exposed pad is the power ground connection. It must be soldered to the PCB and electrically connected to ground through the shortest and lowest impedance connection possible and to the PCB ground plane for rated thermal performance. 31151fb For more information www.linear.com/LTC3115-1 11 LTC3115-1 Block Diagram Pin numbers are shown for the DHD package only. 14 15 2 3 SW2 SW1 PVIN A 10 PVOUT D B 3A –1.5A + – 0A + – C PGND PGND VIN CURRENT LIMIT + – REVERSE CURRENT LIMIT REVERSE BLOCKING LDO PVCC* ZERO CURRENT GATE DRIVES BST2 BST1 1.21V 1000mV 6 7 VC VIN FB 1000mV SOFT-START RAMP – + + ÷ 11 VCC BANDGAP REFERENCE PWM 13 VCC* + – INPUT UVLO 12 9 VIN 2.4V VIN 0.5µA 8 16 RT OSCILLATOR PWM/SYNC MODE SELECTION BURST/PWM (PWM MODE IF PWM/SYNC IS HIGH OR SWITCHING) + – CHIP ENABLE UVLO GND GND 5 4 EXPOSED PAD 1 1.21V VCC 2.4V OVERTEMPERATURE PGND 17 *PVCC AND VCC MUST BE CONNECTED TOGETHER IN THE APPLICATION THE EXPOSED PAD IS AN ELECTRICAL CONNECTION AND MUST BE SOLDERED TO THE BOARD AND ELECTRICALLY CONNECTED TO GROUND 12 + – RUN 3115 BD 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Operation INTRODUCTION The LTC3115-1 is a monolithic buck-boost converter that can operate with input and output voltages from as low as 2.7V to as high as 40V. Four internal low resistance Nchannel DMOS switches minimize the size of the application circuit and reduce power losses to maximize efficiency. Internal high side gate drivers, which require only the addition of two small external capacitors, further simplify the design process. A proprietary switch control algorithm allows the buck-boost converter to maintain output voltage regulation with input voltages that are above, below or equal to the output voltage. Transitions between these operating modes are seamless and free of transients and subharmonic switching. The LTC3115-1 can be configured to operate over a wide range of switching frequencies, from 100kHz to 2MHz, allowing applications to be optimized for board area and efficiency. With its configurability and wide operating voltage range, the LTC3115-1 is ideally suited to a wide range of power systems especially those requiring compatibility with a variety of input power sources such as lead-acid batteries, USB ports, and industrial supply rails as well as from power sources which have wide or poorly controlled voltage ranges such as FireWire and unregulated wall adapters. The LTC3115-1 has an internal fixed-frequency oscillator with a switching frequency that is easily set by a single external resistor. In noise sensitive applications, the converter can also be synchronized to an external clock via the PWM/SYNC pin. The LTC3115-1 has been optimized to reduce input current in shutdown and standby for applications which are sensitive to quiescent current draw, such as battery-powered devices. In Burst Mode operation, the no-load standby current is only 50µA (typical) and in shutdown the total supply current is reduced to 3µA (typical). switching spectrum. A proprietary switching algorithm provides seamless transitions between operating modes and eliminates discontinuities in the average inductor current, inductor current ripple, and loop transfer function throughout all regions of operation. These advantages result in increased efficiency, improved loop stability, and lower output voltage ripple in comparison to the traditional 4-switch buck-boost converter. Figure 1 shows the topology of the LTC3115-1 power stage which is comprised of four N-channel DMOS switches and their associated gate drivers. In PWM mode operation both switch pins transition on every cycle independent of the input and output voltage. In response to the error amplifier output, an internal pulse width modulator generates the appropriate switch duty cycles to maintain regulation of the output voltage. When stepping down from a high input voltage to a lower output voltage, the converter operates in buck mode and switch D remains on for the entire switching cycle except for the minimum switch low duration (typically 100ns). During the switch low duration switch C is turned on which forces SW2 low and charges the flying capacitor, CBST2, to ensure that the voltage of the switch D gate driver supply rail is maintained. The duty cycle of switches A and B are adjusted to provide the appropriate buck mode duty cycle. If the input voltage is lower than the output voltage, the converter operates in boost mode. Switch A remains on for the entire switching cycle except for the minimum switch low duration (typically 100ns) while switches C and D are modulated to maintain the required boost mode CBST1 BST1 PVIN SW1 SW2 PVOUT BST2 PVCC PVCC PWM MODE OPERATION A With the PWM/SYNC pin forced high or driven by an external clock, the LTC3115-1 operates in a fixed-frequency pulse width modulation (PWM) mode using a voltage mode control loop. This mode of operation maximizes the output current that can be delivered by the converter, reduces output voltage ripple, and yields a low noise fixed-frequency CBST2 L D LTC3115-1 PVCC B PGND PVCC C PGND 31151 F01 Figure 1. Power Stage Schematic 31151fb For more information www.linear.com/LTC3115-1 13 LTC3115-1 Operation duty cycle. The minimum switch low duration ensures that flying capacitor CBST1 is charged sufficiently to maintain the voltage on the BST1 rail. Oscillator and Phase-Locked Loop LTC3115-1 RFF RTOP CFF 1000mV FB VIN + – ÷ RBOT The LTC3115-1 operates from an internal oscillator with a switching frequency that is configured by a single external resistor between the RT pin and ground. For noise sensitive applications, an internal phase-locked loop allows the LTC3115-1 to be synchronized to an external clock signal applied to the PWM/SYNC pin. The phase-locked loop is only able to increase the frequency of the internal oscillator to obtain synchronization. Therefore, the RT resistor must be chosen to program the internal oscillator to a lower frequency than the frequency of the clock applied to the PWM/SYNC pin. Sufficient margin must be included to account for the frequency variation of the external synchronization clock as well as the worst-case variation in frequency of the internal oscillator. Whether operating from its internal oscillator or synchronized to an external clock signal, the LTC3115-1 is able to operate with a switching frequency from 100kHz to 2MHz, providing the ability to minimize the size of the external components and optimize the power conversion efficiency. Error Amplifier and VIN Divider The LTC3115-1 has an internal high gain operational amplifier which provides frequency compensation of the control loop that maintains output voltage regulation. To ensure stability of this control loop, an external compensation network must be installed in the application circuit. A Type III compensation network as shown in Figure 2 is recommended for most applications since it provides the flexibility to optimize the converter’s transient response while simultaneously minimizing any DC error in the output voltage. As shown in Figure 2, the error amplifier is followed by an internal analog divider which adjusts the loop gain by the reciprocal of the input voltage in order to minimize loop-gain variation over changes in the input voltage. This simplifies design of the compensation network and optimizes the transient response over the entire range of input voltages. Details on designing the compensation 14 VOUT PWM VC CFB RFB 31151 F02 CPOLE Figure 2. Error Amplifier and Compensation Network network in LTC3115-1 applications can be found in the Applications Information section of this data sheet. Inductor Current Limits The LTC3115-1 has two current limit circuits that are designed to limit the peak inductor current to ensure that the switch currents remain within the capabilities of the IC during output short-circuit or overload conditions. The primary inductor current limit operates by injecting a current into the feedback pin which is proportional to the extent that the inductor current exceeds the current limit threshold (typically 3A). Due to the high gain of the feedback loop, this injected current forces the error amplifier output to decrease until the average current through the inductor is approximately reduced to the current limit threshold. This current limit circuit maintains the error amplifier in an active state to ensure a smooth recovery and minimal overshoot once the current limit fault condition is removed. However, the reaction speed of this current limit circuit is limited by the dynamics of the error amplifier. On a hard output short, it is possible for the inductor current to increase substantially beyond the current limit threshold before the average current limit has time to react and reduce the inductor current. For this reason, there is a second current limit circuit which turns off power switch A if the current through switch A exceeds approximately 160% of the primary inductor current limit threshold. This provides additional protection in the case of an instantaneous hard output short and provides time for the primary current limit to react. In addition, if VOUT falls below 1.85V, the inductor current limit is folded back to half its nominal value in order to minimize power dissipation. 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Operation Reverse Current Limit Burst Mode OPERATION In PWM mode operation, the LTC3115-1 synchronously switches all four power devices. As a result, in addition to being able to supply current to the output, the converter has the ability to actively conduct current away from the output if that is necessary to maintain regulation. If the output is held above regulation, this could result in large reverse currents. This situation can occur if the output of the LTC3115-1 is held up momentarily by another supply as may occur during a power-up or power-down sequence. To prevent damage to the part under such conditions, the LTC3115-1 has a reverse current comparator that monitors the current entering power switch D from the load. If this current exceeds 1.5A (typical) switch D is turned off for the remainder of the switching cycle in order to prevent the reverse inductor current from reaching unsafe levels. When the PWM/SYNC pin is held low, the buck-boost converter employs Burst Mode operation using a variable frequency switching algorithm that minimizes the no-load input quiescent current and improves efficiency at light load by reducing the amount of switching to the minimum level required to support the load. The output current capability in Burst Mode operation is substantially lower than in PWM mode and is intended to support light standby loads (typically under 50mA). Curves showing the maximum Burst Mode load current as a function of the input and output voltage can be found in the Typical Characteristics section of this data sheet. If the converter load in Burst Mode operation exceeds the maximum Burst Mode current capability, the output will lose regulation. Output Current Capability The maximum output current that can be delivered by the LTC3115-1 is dependent upon many factors, the most significant being the input and output voltages. For VOUT = 5V and VIN ≥ 3.6V, the LTC3115-1 is able to support up to a 1A load continuously. For VOUT = 12V and VIN ≥ 12V, the LTC3115-1 is able to support up to a 2A load continuously. Typically, the output current capability is greatest when the input voltage is approximately equal to the output voltage. At larger step-up voltage ratios, the output current capability is reduced because the lower duty cycle of switch D results in a larger inductor current being needed to support a given load. Additionally, the output current capability generally decreases at large step-down voltage ratios due to higher inductor current ripple which reduces the maximum attainable inductor current. The output current capability can also be affected by inductor characteristics. An inductor with large DC resistance will degrade output current capability, particularly in boost mode operation. Larger value inductors generally maximize output current capability by reducing inductor current ripple. In addition, higher switching frequencies (especially above 750kHz) will reduce the maximum output current that can be supplied (see the Typical Performance Characteristics for details). Each Burst Mode cycle is initiated when switches A and C turn on producing a linearly increasing current through the inductor. When the inductor current reaches the Burst Mode current limit (1A typically) switches B and D are turned on, discharging the energy stored in the inductor into the output capacitor and load. Once the inductor current reaches zero, all switches are turned off and the cycle is complete. Current pulses generated in this manner are repeated as often as necessary to maintain regulation of the output voltage. In Burst Mode operation, the error amplifier is not used but is instead placed in a low current standby mode to reduce supply current and improve light load efficiency. SOFT-START To minimize input current transients on power-up, the LTC3115-1 incorporates an internal soft-start circuit with a nominal duration of 9ms. The soft-start is implemented by a linearly increasing ramp of the error amplifier reference voltage during the soft-start duration. As a result, the duration of the soft-start period is largely unaffected by the size of the output capacitor or the output regulation voltage. Given the closed-loop nature of the soft-start implementation, the converter is able to respond to load transients that occur during the soft-start interval. The soft-start period is reset by thermal shutdown and UVLO events on both VIN and VCC. 31151fb For more information www.linear.com/LTC3115-1 15 LTC3115-1 Operation VCC REGULATOR An internal low dropout regulator generates the 4.45V (nominal) VCC rail from VIN. The VCC rail powers the internal control circuitry and power device gate drivers of the LTC3115-1. The VCC regulator is disabled in shutdown to reduce quiescent current and is enabled by forcing the RUN pin above its logic threshold. The VCC regulator includes current limit protection to safeguard against short circuiting of the VCC rail. For applications where the output voltage is set to 5V, the VCC rail can be driven from the output rail through a Schottky diode. Bootstrapping in this manner can provide a significant efficiency improvement, particularly at large voltage step down ratios, and may also allow operation down to a lower input voltage. The maximum operating voltage for the VCC pin is 5.5V. When forcing VCC externally, care must be taken to ensure that this limit is not exceeded. UNDERVOLTAGE LOCKOUT To eliminate erratic behavior when the input voltage is too low to ensure proper operation, the LTC3115-1 incorporates internal undervoltage lockout (UVLO) circuitry. There are two UVLO comparators, one that monitors VIN and another that monitors VCC. The buck-boost converter is disabled if either VIN or VCC falls below its respective UVLO threshold. The input voltage UVLO comparator has a falling threshold of 2.4V (typical). If the input voltage falls below this level all switching is disabled until the input voltage rises above 2.6V (nominal). The VCC UVLO has a falling threshold of 2.4V. If VCC falls below this threshold the buck-boost converter is prevented from switching until VCC rises above 2.6V. Depending on the particular application circuit it is possible that either of these UVLO thresholds could be the factor limiting the minimum input operating voltage of the LTC3115-1. The dominant factor depends on the voltage drop between VIN and VCC which is determined by the dropout voltage of the VCC regulator and is proportional to the total load current drawn from VCC. The load current on the VCC regulator is principally generated by the gate driver supply currents which are proportional to operating frequency and generally increase with larger 16 input and output voltages. As a result, at higher switching frequencies and higher input and output voltages the VCC regulator dropout voltage will increase, making it more likely that the VCC UVLO threshold could become the limiting factor. Curves provided in the Typical Performance Characteristics section of this data sheet show the typical VCC current and can be used to estimate the VCC regulator dropout voltage in a particular application. In applications where VCC is bootstrapped (powered by VOUT or by an auxiliary supply rail through a Schottky diode) the minimum input operating voltage will be limited only by the input voltage UVLO threshold. RUN PIN COMPARATOR In addition to serving as a logic-level input to enable the IC, the RUN pin features an accurate internal comparator allowing it to be used to set custom rising and falling input undervoltage lockout thresholds with the addition of an external resistor divider. When the RUN pin is driven above its logic threshold (typically 0.8V) the VCC regulator is enabled which provides power to the internal control circuitry of the IC and the accurate RUN pin comparator is enabled. If the RUN pin voltage is increased further so that it exceeds the RUN comparator threshold (1.21V nominal), the buck-boost converter will be enabled. If the RUN pin is brought below the RUN comparator threshold, the buck-boost converter will inhibit switching, but the VCC regulator and control circuitry will remain powered unless the RUN pin is brought below its logic threshold. Therefore, in order to place the part in shutdown and reduce the input current to its minimum level (3µA typical) it is necessary to ensure that the RUN pin is brought below the worst-case logic threshold (0.3V). The RUN pin is a high voltage input and can be connected directly to VIN to continuously enable the part when the input supply is present. If the RUN pin is forced above approximately 5V it will sink a small current as given by the following equation: IRUN ≅ VRUN – 5V 5MΩ With the addition of an external resistor divider as shown in Figure 3, the RUN pin can be used to establish a custom 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Operation VIN THERMAL CONSIDERATIONS LTC3115-1 0.5µA VIN R1 RUN R2 0.8V 1.21V – + + – ENA ENABLE SWITCHING ENABLE VCC REGULATOR AND CONTROL CIRCUITS INPUT LOGIC THRESHOLD 31151 F03 Figure 3. Accurate RUN Pin Comparator input undervoltage lockout threshold. The buck-boost converter is enabled when the RUN pin reaches 1.21V which allows the rising UVLO threshold to be set via the resistor divider ratio. Once the RUN pin reaches the threshold voltage, the comparator switches and the buck-boost converter is enabled. In addition, an internal 0.5µA (typical) current source is enabled which sources current out of the RUN pin raising the RUN pin voltage away from the threshold. In order to disable the part, VIN must be reduced sufficiently to overcome the hysteresis generated by this current as well as the 100mV hysteresis of the RUN comparator. As a result, the amount of hysteresis can be independently programmed without affecting the rising UVLO threshold by scaling the values of both resistors. The power switches in the LTC3115-1 are designed to operate continuously with currents up to the internal current limit thresholds. However, when operating at high current levels there may be significant heat generated within the IC. In addition, in many applications the VCC regulator is operated with large input-to-output voltage differentials resulting in significant levels of power dissipation in its pass element which can add significantly to the total power dissipated within the IC. As a result, careful consideration must be given to the thermal environment of the IC in order to optimize efficiency and ensure that the LTC3115-1 is able to provide its full-rated output current. Specifically, the exposed die attach pad of both the DHD and FE packages should be soldered to the PC board and the PC board should be designed to maximize the conduction of heat out of the IC package. This can be accomplished by utilizing multiple vias from the die attach pad connection to other PCB layers containing a large area of exposed copper. If the die temperature exceeds approximately 165°C, the IC will enter overtemperature shutdown and all switching will be inhibited. The part will remain disabled until the die cools by approximately 10°C. The soft-start circuit is re-initialized in overtemperature shutdown to provide a smooth recovery when the fault condition is removed. 31151fb For more information www.linear.com/LTC3115-1 17 LTC3115-1 Applications Information The standard LTC3115-1 application circuit is shown as the typical application on the front page of this data sheet. The appropriate selection of external components is dependent upon the required performance of the IC in each particular application given considerations and trade-offs such as PCB area, cost, output and input voltage, allowable ripple voltage, efficiency and thermal considerations. This section of the data sheet provides some basic guidelines and considerations to aid in the selection of external components and the design of the application circuit. VCC Capacitor Selection The VCC output on the LTC3115-1 is generated from the input voltage by an internal low dropout regulator. The VCC regulator has been designed for stable operation with a wide range of output capacitors. For most applications, a low ESR ceramic capacitor of at least 4.7µF should be utilized. The capacitor should be placed as close to the pin as possible and should connect to the PVCC pin and ground through the shortest traces possible. The PVCC pin is the regulator output and is also the internal supply pin for the gate drivers and boost rail charging diodes. The VCC pin is the supply connection for the remainder of the control circuitry. The PVCC and VCC pins must be connected together on the application PCB. If the trace connecting VCC to PVCC cannot be made via a short connection, an additional 0.1µF bypass capacitor should be placed between the VCC pin and ground using the shortest connections possible. Inductor Selection The choice of inductor used in LTC3115-1 application circuits influences the maximum deliverable output current, the magnitude of the inductor current ripple, and the power conversion efficiency. The inductor must have low DC series resistance or output current capability and efficiency will be compromised. Larger inductance values reduce inductor current ripple and will therefore generally yield greater output current capability. For a fixed DC resistance, a larger value of inductance will yield higher efficiency by reducing the peak current to be closer to the average output current and therefore minimize resistive losses due to high RMS currents. However, a larger inductor value within any given inductor family will generally 18 have a greater series resistance, thereby counteracting this efficiency advantage. In general, inductors with larger inductance values and lower DC resistance will increase the deliverable output current and improve the efficiency of LTC3115-1 applications. An inductor used in LTC3115-1 applications should have a saturation current rating that is greater than the worst-case average inductor current plus half the ripple current. The peak-to-peak inductor current ripple for each operational mode can be calculated from the following formula, where f is the switching frequency, L is the inductance, and tLOW is the switch pin minimum low time. The switch pin minimum low time can be determined from curves given in the Typical Performance Characteristics section of this data sheet. ∆IL(P-P)(BUCK) = VOUT VIN – VOUT 1 – tLOW L VIN f ∆IL(P-P)(BOOST ) = VIN VOUT – VIN 1 – tLOW L VOUT f In addition to its influence on power conversion efficiency, the inductor DC resistance can also impact the maximum output current capability of the buck-boost converter particularly at low input voltages. In buck mode, the output current of the buck-boost converter is generally limited only by the inductor current reaching the current limit threshold. However, in boost mode, especially at large step-up ratios, the output current capability can also be limited by the total resistive losses in the power stage. These include switch resistances, inductor resistance, and PCB trace resistance. Use of an inductor with high DC resistance can degrade the output current capability from that shown in the Typical Performance Characteristics section of this data sheet. As a guideline, in most applications the inductor DC resistance should be significantly smaller than the typical power switch resistance of 150mΩ. Different inductor core materials and styles have an impact on the size and price of an inductor at any given current rating. Shielded construction is generally preferred as it minimizes the chances of interference with other circuitry. The choice of inductor style depends upon the price, sizing, and EMI requirements of a particular application. Table 1 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Applications Information provides a small sampling of inductors that are well suited to many LTC3115-1 applications. In applications with VOUT ≥ 20V, it is recommended that a minimum inductance value, LMIN, be utilized where f is the switching frequency: LMIN = capacitance, tLOW is the switch pin minimum low time, and ILOAD is the output current. Curves for the value of tLOW as a function of switching frequency and temperature can be found in Typical Performance Characteristics section of this data sheet. 12H ( f / Hz ) ∆VP-P(BUCK) = Table 1. Representative Surface Mount Inductors PART NUMBER VALUE DCR MAX DC (µH) (mΩ) CURRENT (A) SIZE (mm) W×L×H Coilcraft LPS6225 LPS6235 MSS1038 D03316P 4.7 6.8 22 15 65 75 70 50 3.2 2.8 3.3 3.0 6.2 × 6.2 × 2.5 6.2 × 6.2 × 3.5 10.2 × 10.5 × 3.8 12.9 × 9.4 × 5.2 Cooper-Bussmann CD1-150-R DR1030-100-R FP3-8R2-R DR1040-220-R 15 10 8.2 22 50 40 74 54 3.6 3.18 3.4 2.9 10.5 × 10.4 × 4.0 10.3 × 10.5 × 3.0 7.3 × 6.7 × 3.0 10.3 × 10.5 × 4.0 Panasonic ELLCTV180M ELLATV100M 18 10 30 23 3.0 3.3 12 × 12 × 4.2 10 × 10 × 4.2 Sumida CDRH8D28/HP CDR10D48MNNP CDRH8D28NP 10 39 4.7 78 105 24.7 3.0 3.0 3.4 8.3 × 8.3 × 3 10.3 × 10.3 × 5 8.3 × 8.3 × 3 Taiyo-Yuden NR10050T150M 15 46 3.6 9.8 × 9.8 × 5 TOKO B1047AS-6R8N B1179BS-150M 892NAS-180M 6.8 15 18 36 56 42 2.9 3.3 3.0 7.6 × 7.6 × 5 10.3 × 10.3 × 4 12.3 × 12.3 × 4.5 Würth 7447789004 744771133 744066150 4.7 33 15 33 49 40 2.9 2.7 3.2 7.3 × 7.3 × 3.2 12 × 12 × 6 10 × 10 × 3.8 ILOAD tLOW COUT ∆VP-P(BOOST) = ILOAD VOUT – VIN + tLOW fVIN fCOUT VOUT The output voltage ripple increases with load current and is generally higher in boost mode than in buck mode. These expressions only take into account the output voltage ripple that results from the output current being discontinuous. They provide a good approximation to the ripple at any significant load current but underestimate the output voltage ripple at very light loads where output voltage ripple is dominated by the inductor current ripple. In addition to output voltage ripple generated across the output capacitance, there is also output voltage ripple produced across the internal resistance of the output capacitor. The ESR-generated output voltage ripple is proportional to the series resistance of the output capacitor and is given by the following expressions where RESR is the series resistance of the output capacitor and all other terms are as previously defined. ∆VP-P(BUCK) = ILOADRESR ≅I R 1– tLOW f LOAD ESR ∆VP-P(BOOST) = V ILOADRESR VOUT ≅ILOAD RESR OUT VIN (1– tLOW f ) VIN Output Capacitor Selection Input Capacitor Selection A low ESR output capacitor should be utilized at the buckboost converter output in order to minimize output voltage ripple. Multilayer ceramic capacitors are an excellent option as they have low ESR and are available in small footprints. The capacitor value should be chosen large enough to reduce the output voltage ripple to acceptable levels. Neglecting the capacitor ESR and ESL, the peak-to-peak output voltage ripple can be calculated by the following formulas, where f is the switching frequency, COUT is the The PVIN pin carries the full inductor current and provides power to internal control circuits in the IC. To minimize input voltage ripple and ensure proper operation of the IC, a low ESR bypass capacitor with a value of at least 4.7µF should be located as close to this pin as possible. The traces connecting this capacitor to PVIN and the ground plane should be made as short as possible. The VIN pin provides power to the VCC regulator and other internal circuitry. If the PCB trace connecting VIN to PVIN is long, it 31151fb For more information www.linear.com/LTC3115-1 19 LTC3115-1 Applications Information may be necessary to add an additional small value bypass capacitor near the VIN pin. When powered through long leads or from a high ESR power source, a larger value bulk input capacitor may be required. In such applications, a 47µF to 100µF electrolytic capacitor in parallel with a 1µF ceramic capacitor generally yields a high performance, low cost solution. Recommended Input and Output Capacitors The capacitors used to filter the input and output of the LTC3115-1 must have low ESR and must be rated to handle the large AC currents generated by switching converters. This is important to maintain proper functioning of the IC and to reduce output voltage ripple. There are many capacitor types that are well suited to such applications including multilayer ceramic, low ESR tantalum, OS-CON and POSCAP technologies. In addition, there are certain types of electrolytic capacitors such as solid aluminum organic polymer capacitors that are designed for low ESR and high AC currents and these are also well suited to LTC3115-1 applications (Table 2). The choice of capacitor technology is primarily dictated by a trade-off between cost, size and leakage current. Notice that some capacitors such as the OS-CON and POSCAP technologies can exhibit significant DC leakage currents which may limit their applicability in devices which require low no-load quiescent current in Burst Mode operation. Ceramic capacitors are often utilized in switching converter applications due to their small size, low ESR, and low leakage currents. However, many ceramic capacitors designed for power applications experience significant loss in capacitance from their rated value with increased DC bias voltages. For example, it is not uncommon for a small surface mount ceramic capacitor to lose more than 50% of its rated capacitance when operated near its rated voltage. As a result, it is sometimes necessary to use a larger value capacitance or a capacitor with a higher voltage rating than required in order to actually realize the intended capacitance at the full operating voltage. To ensure that the intended capacitance is realized in the application circuit, be sure to consult the capacitor vendor’s curve of capacitance versus DC bias voltage. 20 Table 2. Representative Bypass and Output Capacitors MANUFACTURER, PART NUMBER VALUE (µF) VOLTAGE (V) SIZE L × W × H (mm), TYPE, ESR AVX 12103D226MAT2A 22 25 3.2 × 2.5 × 2.79 X5R Ceramic TPME226K050R0075 22 50 7.3 × 4.3 × 4.1 Tantalum, 75mΩ Kemet C2220X226K3RACTU 22 25 5.7 × 5.0 × 2.4 X7R Ceramic A700D226M016ATE030 22 16 7.3 × 4.3 × 2.8 Alum. Polymer, 30mΩ Murata GRM32ER71E226KE15L 22 25 3.2 × 2.5 × 2.5 X7R Ceramic Nichicon PLV1E121MDL1 82 25 8 × 8 × 12 Alum. Polymer, 25mΩ Panasonic ECJ-4YB1E226M 22 25 3.2 × 2.5 × 2.5 X5R Ceramic Sanyo 25TQC22MV 22 25 7.3 × 4.3 × 3.1 POSCAP, 50mΩ 16TQC100M 100 16 7.3 × 4.3 × 1.9 POSCAP, 45mΩ 25SVPF47M 47 25 6.6 × 6.6 × 5.9 OS-CON, 30mΩ Taiyo Yuden UMK325BJ106MM-T 10 50 3.2 × 2.5 × 2.5 X5R Ceramic TMK325BJ226MM-T 22 25 3.2 × 2.5 × 2.5 X5R Ceramic TDK KTJ500B226M55BFT00 22 50 6.0 × 5.3 × 5.5 X7R Ceramic C5750X7R1H106M 10 50 5.7 × 5.0 × 2.0 X7R Ceramic CKG57NX5R1E476M 47 25 6.5 × 5.5 × 5.5 X5R Ceramic Vishay 94SVPD476X0035F12 47 35 10.3 × 10.3 × 12.6 OS-CON, 30mΩ 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Applications Information Programming Custom Input UVLO Thresholds With the addition of an external resistor divider connected to the input voltage as shown in Figure 4, the RUN pin can be used to program the input voltage at which the LTC3115-1 is enabled and disabled. For a rising input voltage, the LTC3115-1 is enabled when VIN reaches the threshold given by the following equation, where R1 and R2 are the values of the resistor divider resistors: When using the additional RH resistor, the rising RUN pin threshold remains as given by the original equation and the hysteresis is given by the following expression: R R2+RH R1+R1R2 VHYST = R1+R2 0.1V + H (0.5µA ) R2 R2 R1+R2 R2 VTH(RISING) = 1.21V VIN R1 To ensure robust operation in the presence of noise, the RUN pin has two forms of hysteresis. A fixed 100mV of hysteresis within the RUN pin comparator provides a minimum RUN pin hysteresis equal to 8.3% of the input turn-on voltage independent of the resistor divider values. In addition, an internal hysteresis current that is sourced from the RUN pin during operation generates an additive level of hysteresis which can be programmed by the value of R1 to increase the overall hysteresis to suit the requirements of specific applications. Once the IC is enabled, it will remain enabled until the input voltage drops below the comparator threshold by the hysteresis voltage, VHYST , as given by the following equation where R1 and R2 are values of the divider resistors: to 2MΩ). In such cases, the amount of hysteresis can be increased further through the addition of an additional resistor, RH, as shown in Figure 5. VHYST = R1• 0.5µA + R1+R2 0.1V R2 Therefore, the rising UVLO threshold and amount of hysteresis can be independently programmed via appropriate selection of resistors R1 and R2. For high levels of hysteresis, the value of R1 can become larger than is desirable in a practical implementation (greater than 1MΩ VIN R1 LTC3115-1 RUN R2 GND 31151 F04 Figure 4. Setting the Input UVLO Threshold and Hysteresis R2 RH LTC3115-1 RUN GND 3115 F05 Figure 5. Increasing Input UVLO hysteresis To improve the noise robustness and accuracy of the UVLO thresholds, the RUN pin input can be filtered by adding a 1000pF capacitor from RUN to GND. Larger valued capacitors should not be utilized because they could interfere with operation of the hysteresis. Bootstrapping the VCC Regulator The high and low side gate drivers are powered through the PVCC rail which is generated from the input voltage through an internal linear regulator. In some applications, especially at higher operating frequencies and high input and output voltages, the power dissipation in the linear VCC regulator can become a key factor in the conversion efficiency of the converter and can even become a significant source of thermal heating. For example, at a 1.2MHz switching frequency, an input voltage of 36V, and an output voltage of 24V, the total PVCC/VCC current is approximately 18mA as shown in the Typical Performance Characteristics section of this data sheet. As a result, this will generate 568mW of power dissipation in the VCC regulator which will result in an increase in die temperature of approximately 24° above ambient in the DFN package. This significant power loss will have a substantial impact on the conversion efficiency and the additional heating may limit the maximum ambient operating temperature for the application. 31151fb For more information www.linear.com/LTC3115-1 21 LTC3115-1 Applications Information A significant performance advantage can be attained in applications which have the converter output voltage programmed to 5V if the output voltage is utilized to power the PVCC and VCC rails. This can be done by connecting a Schottky diode from VOUT to PVCC/VCC as shown in Figure 6. With this bootstrap diode installed, the gate driver currents are generated directly by the buck-boost converter at high efficiency rather than through the internal linear regulator. To minimize current drawn from the output, the internal VCC regulator contains reverse blocking circuitry which minimizes the current into the PVCC/VCC pins when they are driven above the input voltage. The gain term, GBUCK, is comprised of three different components: the gain of the analog divider, the gain of the pulse width modulator, and the gain of the power stage as given by the following expressions where VIN is the input voltage to the converter, f is the switching frequency, R is the load resistance, and tLOW is the switch pin minimum low time. Curves showing the switch pin minimum low time can be found in the Typical Performance Characteristics section of this data sheet. The parameter RS represents the average series resistance of the power stage and can be approximated as twice the average power switch resistance plus the DC resistance of the inductor. GBUCK = GDIVIDER GPWM GPOWER PVOUT VOUT GDIVIDER = LTC3115-1 VCC PVCC 4.7µF Buck Mode Small-Signal Model The LTC3115-1 uses a voltage mode control loop to maintain regulation of the output voltage. An externally compensated error amplifier drives the VC pin to generate the appropriate duty cycle of the power switches. Use of an external compensation network provides the flexibility for optimization of closed loop performance over the wide variety of output voltages, switching frequencies, and external component values supported by the LTC3115-1. The small-signal transfer function of the buck-boost converter is different in the buck and boost modes of operation and care must be taken to ensure stability in both operating regions. When stepping down from a higher input voltage to a lower output voltage, the converter will operate in buck mode and the small-signal transfer function from the error amplifier output, VC, to the converter output voltage is given by the following equation: 1+ s 2πfZ = GBUCK BUCK MODE 22 1+ 3 (1– tLOW f ) 2V VIN R GPOWER = (1– tLOW f )(R+RS ) GPWM = 31151 F06 Figure 6. Bootstrapping PVCC and VCC VO VC 19.8V VIN s s 2 + 2πfOQ 2πfO Notice that the gain of the analog divider cancels the input voltage dependence of the power stage. As a result, the buck mode gain is well approximated by a constant as given by the following equation: GBUCK = 29.7 R ≅ 29.7 = 29.5dB R+RS The buck mode transfer function has a single zero which is generated by the ESR of the output capacitor. The zero frequency, fZ, is given by the following expression where RC and CO are the ESR and value of the output filter capacitor respectively. fZ = 1 2πRC CO In most applications, an output capacitor with a very low ESR is utilized in order to reduce the output voltage ripple to acceptable levels. Such low values of capacitor ESR result in a very high frequency zero and as a result the zero is commonly too high in frequency to significantly impact compensation of the feedback loop. For more information www.linear.com/LTC3115-1 31151fb LTC3115-1 Applications Information The denominator of the buck mode transfer function exhibits a pair of resonant poles generated by the LC filtering of the power stage. The resonant frequency of the power stage, fO, is given by the following expression where L is the value of the inductor: fO = 1 2π R+RS 1 1 ≅ LCO (R+RC ) 2π LCO The quality factor, Q, has a significant impact on compensation of the voltage loop since a higher Q factor produces a sharper loss of phase near the resonant frequency. The quality factor is inversely related to the amount of damping in the power stage and is substantially influenced by the average series resistance of the power stage, RS. Lower values of RS will increase the Q and result in a sharper loss of phase near the resonant frequency and will require more phase boost or lower bandwidth to maintain an adequate phase margin. Q= LCO (R+RC ) (R+RS ) RRCCO +L +CORS (R+RC ) ≅ LCO L +C R R O S The boost mode gain, GBOOST , is comprised of three components: the analog divider, the pulse width modulator and the power stage. The gain of the analog divider and PWM remain the same as in buck mode operation, but the gain of the power stage in boost mode is given by the following equation: GPOWER ≅ VOUT2 (1– tLOW f ) VIN By combining the individual terms, the total gain in boost mode can be reduced to the following expression. Notice that unlike in buck mode, the gain in boost mode is a function of both the input and output voltage. GBOOST ≅ 29.7VOUT2 VIN 2 In boost mode operation, the frequency of the right half plane zero, fRHPZ, is given by the following expression. The frequency of the right half plane zero decreases at higher loads and with larger inductors. R (1– tLOW f ) VIN2 fRHPZ = 2πL VOUT2 2 Boost Mode Small-Signal Model When stepping up from a lower input voltage to a higher output voltage, the buck-boost converter will operate in boost mode where the small-signal transfer function from control voltage, VC, to the output voltage is given by the following expression. In boost mode, the resonant frequency of the power stage has a dependence on the input and output voltage as shown by the following equation. VO VC = GBOOST BOOST MODE s 1+ s 1– 2πfZ 2πfRHPZ s 2 s + 1+ 2πfO Q 2πfO In boost mode operation, the transfer function is characterized by a pair of resonant poles and a zero generated by the ESR of the output capacitor as in buck mode. However, in addition there is a right half plane zero which generates increasing gain and decreasing phase at higher frequencies. As a result, the crossover frequency in boost mode operation generally must be set lower than in buck mode in order to maintain sufficient phase margin. fO = 1 2π RVIN2 VOUT2 1 VIN ≅ • LCO (R+RC ) 2π VOUT RS + 1 LC Finally, the magnitude of the quality factor of the power stage in boost mode operation is given by the following expression. Q= RV 2 LCOR RS + IN2 VOUT L +CO RS R 31151fb For more information www.linear.com/LTC3115-1 23 LTC3115-1 Applications Information Compensation of the Voltage Loop VOUT The small-signal models of the LTC3115-1 reveal that the transfer function from the error amplifier output, VC, to the output voltage is characterized by a set of resonant poles and a possible zero generated by the ESR of the output capacitor as shown in the Bode plot of Figure 7. In boost mode operation, there is an additional right half plane zero that produces phase lag and increasing gain at higher frequencies. Typically, the compensation network is designed to ensure that the loop crossover frequency is low enough that the phase loss from the right half plane zero is minimized. The low frequency gain in buck mode is a constant, but varies with both VIN and VOUT in boost mode. GAIN RTOP RBOT C1 + – VC GND 31151 F08 Figure 8. Error Amplifier with Type I Compensation In most applications, the low bandwidth of the Type I compensated loop will not provide sufficient transient response performance. To obtain a wider bandwidth feedback loop, optimize the transient response, and minimize the size of the output capacitor, a Type III compensation network as shown in Figure 9 is required. VOUT RFF –40dB/DEC RTOP –20dB/DEC 0° LTC3115-1 1000mV FB RBOT LTC3115-1 1000mV FB CFF CFB RFB CPOLE PHASE + – VC GND 31151 F09 –90° BUCK MODE –180° –270° Figure 9. Error Amplifier with Type III Compensation BOOST MODE fO fRHPZ f 31151 F07 Figure 7. Buck-Boost Converter Bode Plot For charging or other applications that do not require an optimized output voltage transient response, a simple Type I compensation network as shown in Figure 8 can be used to stabilize the voltage loop. To ensure sufficient phase margin, the gain of the error amplifier must be low enough that the resultant crossover frequency of the control loop is well below the resonant frequency. 24 A Bode plot of the typical Type III compensation network is shown in Figure 10. The Type III compensation network provides a pole near the origin which produces a very high loop gain at DC to minimize any steady-state error in the regulation voltage. Two zeros located at fZERO1 and fZERO2 provide sufficient phase boost to allow the loop crossover frequency to be set above the resonant frequency, fO, of the power stage. The Type III compensation network also introduces a second and third pole. The second pole, at frequency fPOLE2, reduces the error amplifier gain to a zero slope to prevent the loop crossover from extending too high in frequency. The third pole at frequency fPOLE3 provides attenuation of high frequency switching noise. 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Applications Information In most applications the compensation network is designed so that the loop crossover frequency is above the resonant frequency of the power stage, but sufficiently below the boost mode right half plane zero to minimize the additional phase loss. Once the crossover frequency is decided upon, the phase boost provided by the compensation network is centered at that point in order to maximize the phase margin. A larger separation in frequency between the zeros and higher order poles will provide a higher peak phase boost but may also increase the gain of the error amplifier which can push out the loop crossover to a higher frequency. GAIN –20dB/DEC –20dB/DEC 90° 0° –90° PHASE fZERO1 fPOLE2 fPOLE3 f 31151 F10 fZERO2 Figure 10. Type III Compensation Bode Plot The transfer function of the compensated Type III error amplifier from the input of the resistor divider to the output of the error amplifier, VC, is: s 1+ 2πf s 1+ 2πf VC (s) ZERO1 ZERO2 = GEA VOUT (s) s s s 1+ 1+ 2πfPOLE2 2πfPOLE3 The error amplifier gain is given by the following equation. The simpler approximate value is sufficiently accurate in most cases since CFB is typically much larger in value than CPOLE. GEA = 1 R TOP (CFB +CPOLE ) ≅ 1 R TOP CFB The pole and zero frequencies of the Type III compensation network can be calculated from the following equations where all frequencies are in Hz, resistances are in ohms, and capacitances are in farads. fZERO1 = fZERO2 = 1 2πRFB CFB 1 1 ≅ 2π (R TOP +RFF ) CFF 2πR TOP CFF CFB +CPOLE 1 fPOLE2 = ≅ 2πCFBCPOLE RFB 2πCPOLE RFB fPOLE3 = The Q of the power stage can have a significant influence on the design of the compensation network because it determines how rapidly the 180° of phase loss in the power stage occurs. For very low values of series resistance, RS, the Q will be higher and the phase loss will occur sharply. In such cases, the phase of the power stage will fall rapidly to –180° above the resonant frequency and the total phase margin must be provided by the compensation network. However, with higher losses in the power stage (larger RS) the Q factor will be lower and the phase loss will occur more gradually. As a result, the power stage phase will not be as close to –180° at the crossover frequency and less phase boost is required of the compensation network. The LTC3115-1 error amplifier is designed to have a fixed maximum bandwidth in order to provide rejection of switching noise to prevent it from interfering with the control loop. From a frequency domain perspective, this can be viewed as an additional single pole as illustrated in Figure 11. The nominal frequency of this pole is 300kHz. For typical loop crossover frequencies below about 50kHz the phase contributed by this additional pole is negligible. However, for loops with higher crossover frequencies this additional phase loss should be taken into account when designing the compensation network. LTC3115-1 1000mV FB VC 1 + – RFILT CFILT INTERNAL VC 31151 F11 Figure 11. Internal Loop Filter 2πCFF RFF 31151fb For more information www.linear.com/LTC3115-1 25 LTC3115-1 Applications Information Loop Compensation Example This section provides an example illustrating the design of a compensation network for a typical LTC3115-1 application circuit. In this example a 5V regulated output voltage is generated with the ability to supply a 500mA load from an input power source ranging from 3.5V to 30V. To reduce switching losses a 750kHz switching frequency has been chosen for this example. In this application the maximum inductor current ripple will occur at the highest input voltage. An inductor value of 8.2µH has been chosen to limit the worst-case inductor current ripple to approximately 600mA. A low ESR output capacitor with a value of 20µF is specified to yield a worst-case output voltage ripple (occurring at the worst-case step-up ratio and maximum load current) of approximately 12mV. In summary, the key power stage specifications for this LTC3115-1 example application are given below. f = 0.75MHz, tLOW = 0.1µs VIN = 3.5V to 30V VOUT = 5V at 500mA COUT = 20µF, RC = 10mΩ L = 8.2µH, RL = 45mΩ With the power stage parameters specified, the compensation network can be designed. In most applications, the most challenging compensation corner is boost mode operation at the greatest step-up ratio and highest load current since this generates the lowest frequency right half plane zero and results in the greatest phase loss. Therefore, a reasonable approach is to design the compensation network at this worst-case corner and then verify that sufficient phase margin exists across all other operating conditions. In this example application, at VIN = 3.5V and the full 500mA load current, the right half plane zero will be located at 81kHz and this will be a dominant factor in determining the bandwidth of the control loop. The first step in designing the compensation network is to determine the target crossover frequency for the com- 26 pensated loop. A reasonable starting point is to assume that the compensation network will generate a peak phase boost of approximately 60°. Therefore, in order to obtain a phase margin of 60°, the loop crossover frequency, fC, should be selected as the frequency at which the phase of the buck-boost converter reaches –180°. As a result, at the loop crossover frequency the total phase will be simply the 60° of phase provided by the error amplifier as shown: Phase Margin = φBUCK-BOOST + φERRORAMPLIFIER + 180° = –180° + 60° + 180° = 60° Similarly, if a phase margin of 45° is required, the target crossover frequency should be picked as the frequency at which the buck-boost converter phase reaches –195° so that the combined phase at the crossover frequency yields the desired 45° of phase margin. This example will be designed for a 60° phase margin to ensure adequate performance over parametric variations and varying operating conditions. As a result, the target crossover frequency, fC, will be the point at which the phase of the buck-boost converter reaches –180°. It is generally difficult to determine this frequency analytically given that it is significantly impacted by the Q factor of the resonance in the power stage. As a result, it is best determined from a Bode plot of the buck-boost converter as shown in Figure 12. This Bode plot is for the LTC3115-1 buck-boost converter using the previously specified power stage parameters and was generated from the small-signal model equations using LTspice® software. In this case, the phase reaches –180° at 24kHz making fC = 24kHz the target crossover frequency for the compensated loop. From the Bode plot of Figure 12 the gain of the power stage at the target crossover frequency is 19dB. Therefore, in order to make this frequency the crossover frequency in the compensated loop, the total loop gain at fC must be adjusted to 0dB. To achieve this, the gain of the compensation network must be designed to be –19dB at the crossover frequency. 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Applications Information 50 40 –80 PHASE 20 –120 10 –160 0 –200 –10 –240 –20 10 –280 fC 100 1k 10k FREQUENCY (Hz) PHASE (DEG) GAIN (dB) –40 GAIN 30 –30 the compensated error amplifier is determined simply by the amount of separation between the poles and zeros as shown by the following equation: 0 100k –320 1M 31151 F12 Figure 12. Converter Bode Plot, VIN = 3.5V, ILOAD = 500mA At this point in the design process, there are three constraints that have been established for the compensation network. It must have –19dB gain at fC = 24kHz, a peak phase boost of 60° and the phase boost must be centered at fC = 24kHz. One way to design a compensation network to meet these targets is to simulate the compensated error amplifier Bode plot in LTspice for the typical compensation network shown on the front page of this data sheet. Then, the gain, pole frequencies and zero frequencies can be iteratively adjusted until the required constraints are met. Alternatively, an analytical approach can be used to design a compensation network with the desired phase boost, center frequency and gain. In general, this procedure can be cumbersome due to the large number of degrees of freedom in a Type III compensation network. However the design process can be simplified by assuming that both compensation zeros occur at the same frequency, fZ, and both higher order poles (fPOLE2 and fPOLE3) occur at the common frequency, fP . In most cases this is a reasonable assumption since the zeros are typically located between 1kHz and 10kHz and the poles are typically located near each other at much higher frequencies. Given this assumption, the maximum phase boost, fMAX, provided by φ MAX = 4 tan –1 fP – 270° fZ A reasonable choice is to pick the frequency of the poles, fP , to be about 50 times higher than the frequency of the zeros, fZ, which provides a peak phase boost of approximately φMAX = 60° as was assumed previously. Next, the phase boost must be centered so that the peak phase occurs at the target crossover frequency. The frequency of the maximum phase boost, fCENTER, is the geometric mean of the pole and zero frequencies as: fCENTER = fP • fZ = 50 • fZ ≅ 7 • fZ Therefore, in order to center the phase boost given a factor of 50 separation between the pole and zero frequencies, the zeros should be located at one seventh of the crossover frequency and the poles should be located at seven times the crossover frequency as given by the following equations: 1 1 fZ = • fC = ( 24kHz ) = 3.43kHz 7 7 fP = 7 • fC = 7 ( 24kHz ) = 168kHz This placement of the poles and zeros will yield a peak phase boost of 60° that is centered at the crossover frequency, fC. Next, in order to produce the desired target crossover frequency, the gain of the compensation network at the point of maximum phase boost, GCENTER, must be set to –19dB. The gain of the compensated error amplifier at the point of maximum phase gain is given by: 2πfP dB GCENTER = 10log ( 2πf )3 (R C )2 Z TOP FB 31151fb For more information www.linear.com/LTC3115-1 27 LTC3115-1 Applications Information Assuming a multiple of 50 separation between the pole frequencies and zero frequencies this can be simplified to the following expression: 50 GCENTER = 20log dB 2πfC R TOP CFB Next, CFF can be chosen to set the second zero, fZERO2, to the common zero frequency of 3.43kHz. This equation completes the set of constraints needed to determine the compensation component values. Specifically, the two zeros, fZERO1 and fZERO2, should be located near 3.43kHz. The two poles, fPOLE2 and fPOLE3, should be located near 168kHz and the gain should be set to provide a gain at the crossover frequency of GCENTER = –19dB. The first step in defining the compensation component values is to pick a value for RTOP that provides an acceptably low quiescent current through the resistor divider. A value of RTOP = 1MΩ is a reasonable choice. Next, the value of CFB can be found in order to set the error amplifier gain at the crossover frequency to –19dB as follows: GCENTER = –19.1dB CFF = 1 2π (1MΩ) ( 3.43kHz) Finally, the resistor value RFF can be chosen to place the second pole at 168kHz. RFF = 1 ≅ 20.0kΩ 2π ( 47pF ) (168Hz) Now that the pole frequencies, zero frequencies and gain of the compensation network have been established, the next step is to generate a Bode plot for the compensated error amplifier to confirm its gain and phase properties. A Bode plot of the error amplifier with the designed compensation component values is shown in Figure 13. The Bode plot confirms that the peak phase occurs at 24kHz and the phase boost at that point is 57.7°. In addition, the gain at the peak phase frequency is –19.3dB which is close to the design target. 50 = 20log 2π ( 24kHz ) (1 MΩ) C FB 50 ≅ 3.0nF The compensation poles can be set at 168kHz and the zeros at 3.43kHz by using the expressions for the pole and zero frequencies given in the previous section. Setting the frequency of the first zero, fZERO1, to 3.43kHz results in the following value for RFB: RFB = 1 ≅ 15.4kΩ 2π ( 3nF ) ( 3.43kHz) 90 5 60 PHASE 0 30 –5 GAIN –10 0 –15 –20 –30 –25 –30 –60 –35 –40 PHASE (DEG) 2π ( 24kHz ) (1MΩ) alog –19.1 20 15 10 GAIN (dB) CFB = ≅ 47pF fC 10 100 1k 10k FREQUENCY (Hz) 100k –90 1M 3115 F13 Figure 13. Compensated Error Amplifier Bode Plot This leaves the free parameter, CPOLE, to set the frequency fPOLE1 to the common pole frequency of 168kHz as given: CPOLE = 28 1 ≅ 62pF 2π (15.4kΩ ) (168kHz) 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Applications Information The final step in the design process is to compute the Bode plot for the entire loop using the designed compensation network and confirm its phase margin and crossover frequency. The complete loop Bode plot for this example is shown in Figure 14. The loop crossover frequency is 22kHz which is close to the design target and the phase margin is approximately 60°. The Bode plot for the complete loop should be checked over all operating conditions and for variations in component values to ensure that sufficient phase margin exists in all cases. The stability of the loop should also be confirmed via time domain simulation and by evaluating the transient response of the converter in the actual circuit. Output Voltage Programming The output voltage is set via the external resistor divider comprised of resistors RTOP and RBOT as show in Figures 8 and 9. The resistor divider values determine the output regulation voltage according to: 60 180 PHASE 40 120 60 GAIN 0 0 PHASE (DEG) 20 GAIN (dB) R VOUT = 1.000V 1+ TOP RBOT –20 –60 –40 –120 –60 fC 10 100 1k 10k FREQUENCY (Hz) 100k In addition to setting the output voltage, the value of RTOP is instrumental in controlling the dynamics of the compensation network. When changing the value of this resistor, care must be taken to understand the impact this will have on the compensation network. In addition, the Thevenin equivalent resistance of the resistor divider controls the gain of the current limit. To maintain sufficient gain in this loop, it is recommended that the value of RTOP be chosen to be 1MΩ or larger. Switching Frequency Selection The switching frequency is set by the value of a resistor connected between the RT pin and ground. The switching frequency, f, is related to the resistor value by the following equation where RT is the resistance: f= 35.7MHz ( RT / kΩ ) Higher switching frequencies facilitate the use of smaller inductors as well as smaller input and output filter capacitors which results in a smaller solution size and reduced component height. However, higher switching frequencies also generally reduce conversion efficiency due to the increased switching losses. In addition, higher switching frequencies (above 750kHz) will reduce the maximum output current that can be supplied (see Typical Performance Characteristics for details). For applications with VOUT ≥ 20V, a maximum switching frequency of 1MHz is recommended. –180 1M 31151 F14 Figure 14. Complete Loop Bode Plot 31151fb For more information www.linear.com/LTC3115-1 29 LTC3115-1 Applications Information PCB Layout Considerations The LTC3115-1 buck-boost converter switches large currents at high frequencies. Special attention should be paid to the PC board layout to ensure a stable, noise-free and efficient application circuit. Figures 16 and 17 show a representative PCB layout for each package option to outline some of the primary considerations. A few key guidelines are provided below: 1. The parasitic inductance and resistance of all circulating high current paths should be minimized. This can be accomplished by keeping the routes to all bold components in Figures 16 and 17 as short and as wide as possible. Capacitor ground connections should via down to the ground plane by way of the shortest route possible. The bypass capacitors on PVIN, PVOUT and PVCC/VCC should be placed as close to the IC as possible and should have the shortest possible paths to ground. 2. The exposed pad is the electrical power ground connection for the LTC3115-1 in the DHD package. Multiple vias should connect the backpad directly to the ground plane. In addition, maximization of the metallization connected to the backpad will improve the thermal environment and improve the power handling capabilities of the IC in both the FE and DHD packages. 3. The components shown in bold and their connections should all be placed over a complete ground plane to minimize loop cross-sectional areas. This minimizes EMI and reduces inductive drops. 4. Connections to all of the components shown in bold should be made as wide as possible to reduce the series resistance. This will improve efficiency and maximize the output current capability of the buck-boost converter. 30 5. To prevent large circulating currents in the ground plane from disrupting operation of the LTC3115-1, all small-signal grounds should return directly to GND by way of a dedicated Kelvin route. This includes the ground connection for the RT pin resistor, and the ground connection for the feedback network as shown in Figures 16 and 17. 6. Keep the routes connecting to the high impedance, noise sensitive inputs FB and RT as short as possible to reduce noise pick-up. 7. The BST1 and BST2 pins transition at the switching frequency to the full input and output voltage respectively. To minimize radiated noise and coupling, keep the BST1 and BST2 routes as short as possible and away from all sensitive circuitry and pins (VC, FB, RT). In many applications the length of traces connecting to the boost capacitors can be minimized by placing the boost capacitors on the back side of the PC board and routing to them via traces on an internal copper layer. 8 Connections from the BST1 and BST2 capacitors must Kelvin directly back to the respective SW pin as shown in Figure 15. THIS ROUTE MUST KELVIN CONNECT DIRECTLY BACK TO THE SW2 PIN SW2 LTC3115-1 0.1µF BST2 31151 F15 Figure 15. Kelvin BST Connections 9. If the optional Schottky diode from SW2 to PVOUT is utilized, the Schottky should be placed as close to the SW2 and PVOUT pins as possible and connected with the shortest possible traces. 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Applications Information VIA TO GROUND PLANE (AND TO INNER LAYER WHERE SHOWN) OPTIONAL SCHOTTKY DIODE [16] PWM/ SYNC [1] RUN [2] SW2 VOUT KELVIN BACK TO GND PIN RBOT RT [17] PGND [15] SW1 VIN [3] PVOUT [14] PVIN [4] GND [13] BST1 CBST1 CBST2 [5] GND [12] BST2 [6] VC [11] PVCC [7] FB [10] VIN [8] RT [9] VCC INNER PCB LAYER ROUTES RTOP KELVIN TO VOUT 31151 F16 UNINTERRUPTED GROUND PLANE SHOULD EXIST UNDER ALL COMPONENTS SHOWN IN BOLD AND UNDER TRACES CONNECTING TO THOSE COMPONENTS Figure 16. PCB Layout Recommended for the DHD Package 31151fb For more information www.linear.com/LTC3115-1 31 LTC3115-1 Applications Information VIA TO GROUND PLANE (AND TO INNER LAYER WHERE SHOWN) OPTIONAL SCHOTTKY DIODE [1] PGND [20] PGND [2] RUN [19] PWM/ SYNC [3] SW2 VOUT KELVIN BACK TO GND PIN RBOT RT [21] PGND [18] SW1 VIN [4] PVOUT [17] PVIN [5] GND [16] BST1 CBST1 CBST2 [6] GND [15] BST2 [7] VC [14] PVCC [8] FB [13] VIN [9] RT [12] VCC [10] PGND [11] PGND INNER PCB LAYER ROUTES RTOP KELVIN TO VOUT 31151 F17 UNINTERRUPTED GROUND PLANE SHOULD EXIST UNDER ALL COMPONENTS SHOWN IN BOLD AND UNDER TRACES CONNECTING TO THOSE COMPONENTS Figure 17. PCB Layout Recommended for the FE Package 32 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Typical Applications Wide Input Voltage Range (2.7V to 40V), High Efficiency 300kHz, Low Noise 5V Regulator L1 33µH CBST1 0.1µF CBST2 0.1µF BST1 SW1 2.7V TO 40V SW2 BST2 PVIN VIN CIN 10µF PVOUT RUN LTC3115-1 VC FB PWM/SYNC PVCC VCC RT RT 121k GND PGND + CO RTOP 330µF 1M CFB RFB 3300pF 93.1k CFF 82pF 5V 1A VIN > 3.6V 2A VIN ≥ 6V RFF 249k 27pF RBOT 249k D1 31151 TA02a C1 4.7µF CIN: MURATA GRM55DR61H106K CO: POSCAP 6TPB330M (7.3mm × 4.3mm × 2.8mm) D1: PANASONIC MA785 L1: COILCRAFT MSS1260 PWM Mode Efficiency vs Load Current 100 100 95 95 90 90 85 85 EFFICIENCY (%) EFFICIENCY (%) PWM Mode Efficiency vs Load Current 80 75 70 65 60 VIN = 5V VIN = 3.6V VIN = 2.7V 55 50 0.01 0.1 LOAD CURRENT (A) 1 80 75 70 65 60 VIN = 12V VIN = 24V VIN = 36V 55 50 0.01 0.1 LOAD CURRENT (A) 31151 TA02b VOUT Transient for a 0A to 1A Load Step 31151 TA02c VOUT Transient for a 0A to 2A Load Step, VIN = 24V VOUT (200mV/DIV) VIN = 36V VOUT (200mV/DIV) VIN = 12V VOUT (200mV/DIV) VOUT (200mV/DIV) VIN = 5V INDUCTOR CURRENT (2A/DIV) VOUT (200mV/DIV) VIN = 3.6V 2ms/DIV 1 LOAD CURRENT (2A/DIV) 31151 TA02d 2ms/DIV 31151 TA02e 31151fb For more information www.linear.com/LTC3115-1 33 LTC3115-1 Typical Applications Wide Input Voltage Range (10V to 40V) 1MHz 24V Supply at 500mA L1 15µH CBST1 0.1µF CBST2 0.1µF BST1 SW1 10V TO 40V UVLO PROGRAMMED TO 10V (1.3V HYSTERESIS) R1 953k SW2 BST2 PVIN VIN CIN 10µF RUN PVOUT RTOP 1M CFB RFB 3300pF 10k LTC3115-1 R2 130k 24V 500mA CO 10µF VC RFF 10k FB RT 35.7k RBOT 43.2k PWM/SYNC PVCC VCC RT GND CFF 22pF C1 4.7µF PGND 31151 TA03a L1: WÜRTH 744 066 150 Maximum Load Current vs VIN Efficiency vs VIN 92 2.5 90 EFFICIENCY (%) LOAD CURRENT (A) 2.0 1.5 1.0 0.5 0 ILOAD = 1A 88 86 84 82 80 10 ILOAD = 0.5A 30 20 INPUT VOLTAGE (V) 40 10 20 30 INPUT VOLTAGE (V) 40 31151 TA03c 31151 TA03b Power-Up/Down Waveforms, ILOAD = 0.5A VIN (5V/DIV) VOUT (10V/DIV) INDUCTOR CURRENT (2A/DIV) 50ms/DIV 34 31151 TA03d 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Typical Applications Industrial 12V 1MHz Regulator with Custom Input Undervoltage Lockout Thresholds L1 10µH CBST2 0.1µF CBST1 0.1µF BST1 SW1 10V TO 40V ENABLED WHEN VIN REACHES 10.6V DISABLED WHEN VIN FALLS BELOW 8.7V CIN 10µF R1 2M SW2 BST2 PVIN VIN PVOUT LTC3115-1 VC RUN R2 255k RT 35.7k CO 22µF CFB RFB 820pF 40.2k FB PWM/SYNC PVCC VCC RT GND 12V 1.4A RTOP 1M CFF 33pF RFF 10k RBOT 90.9k C1 4.7µF PGND 31151 TA04a CIN: MURATA GRM55DR61H106K CO: TDK CKG57NX5R1H226M L1: WÜRTH 744065100 PWM Mode Efficiency vs Load Current 0A to 1.5A Load Step, VIN = 24V 100 VOUT (500mV/DIV) EFFICIENCY (%) 90 80 INDUCTOR CURRENT (1A/DIV) 70 60 VIN = 10.6V VIN = 12V VIN = 24V VIN = 36V 50 40 0.01 0.1 LOAD CURRENT (A) 500µs/DIV 31151 TA04c 1 31151 TA04b 0A to 1.5A Load Step, VIN = 10.6V 0A to 1.5A Load Step, VIN = 40V VOUT (500mV/DIV) VOUT (500mV/DIV) INDUCTOR CURRENT (1A/DIV) INDUCTOR CURRENT (1A/DIV) 500µs/DIV 31151 TA04d 500µs/DIV 31151 TA04e 31151fb For more information www.linear.com/LTC3115-1 35 LTC3115-1 Typical Applications 24V 750kHz Industrial Rail Restorer L1 22µH * CBST1 0.1µF BST1 SW1 20V TO 40V OPEN DRAIN OUTPUT R1 500k SW2 BST2 PVIN VIN CIN 10µF *OPTIONAL: INSTALL IN APPLICATIONS SUBJECT TO OUTPUT OVERLOAD OR SHORT-CIRCUIT CONDITIONS CBST2 0.1µF RUN PVOUT 1µF RFB 25k LTC3115-1 ON OFF + VC CO 82µF CFB 3300pF CFF 47pF RTOP 1M RFF 51k 100pF FB RT PWM/SYNC PVCC VCC GND 24V 1.5A RT 47.5k RBOT 43.2k C1 4.7µF PGND 31151 TA05a CO: OS-CON 35SVPF82M L1: TOKO 892NBS-220M Regulated Output Voltage from a Time Varying Input Rail 40V VIN (5V/DIV) 0A to 1.5A Load Step, VIN = 20V LOAD CURRENT (1A/DIV) VOUT (1V/DIV) VOUT (5V/DIV) INDUCTOR CURRENT (2A/DIV) 20V 31151 TA05b 10ms/DIV 500µs/DIV 31151 TA05c Efficiency vs Load Current 100 90 EFFICIENCY (%) 80 70 60 50 40 VIN = 20V VIN = 24V VIN = 36V 30 20 0.01 0.10 LOAD CURRENT (A) 1 31151 TA05d 36 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Typical Applications USB, FireWire, Automotive and Unregulated Wall Adapter to Regulated 5V (750kHz) USB 4.1V TO 5.5V FireWire 8V TO 36V AUTOMOTIVE 3.6V TO 40V WALL ADAPTER 4V TO 40V D1 D2 L1 10µH CBST2 0.1µF CBST1 0.1µF D3 D4 BST1 SW1 10µF SW2 BST2 PVIN VIN PVOUT LTC3115-1 PWM/SYNC BURST PWM VC RUN OFF ON CO 47µF ×2 CFB RFB 4700pF 100k FB RT 47.5k GND RTOP 1M CFF 47pF RFF 51k RBOT 249k PVCC VCC RT 5V 750mA C1 4.7µF PGND 31151 TA06a CIN: MURATA GRM55DR61H106K CO: GRM43ER60J476 D1-D4: B360A-13-F L1: COILCRAFT LPS6225 Soft-Start Waveform, VIN = 24V, ILOAD = 0.5A VRUN (5V/DIV) VCC (5V/DIV) Efficiency vs Load Current, from Automotive Input VOUT (2V/DIV) 100 INDUCTOR CURRENT (500mA/DIV) 90 2ms/DIV EFFICIENCY (%) 80 31151 TA06c 70 Output Voltage Transient Response, 750mA Load Step, Powered from Automotive Input 60 50 VIN = 3.6V VIN = 5V VIN = 12V VIN = 24V VIN = 36V 40 30 20 0.01 0.1 LOAD CURRENT (A) 1 31151 TA06b VOUT (200mV/DIV) VIN = 36V VOUT (200mV/DIV) VIN = 12V VOUT (200mV/DIV) VIN = 3.6V 1ms/DIV 31151 TA06d 31151fb For more information www.linear.com/LTC3115-1 37 LTC3115-1 Typical Applications Miniature Size 1.5MHz 12V Supply L1 4.7µH CBST2 0.1µF CBST1 0.1µF BST1 SW1 6V TO 40V CI 4.7µF SW2 BST2 PVIN VIN PVOUT RUN LTC3115-1 BURST PWM RT 23.7k PWM/SYNC VC RT FB CO 10µF CFB RFB 1000pF 15k RTOP 1M CFF 33pF RFF 15k RBOT 90.9k PVCC VCC GND 12V AT 500mA 1A VIN > 10V C1 4.7µF PGND 31151 TA07a CO: MURATA GRM55DR61H106K L1: WÜRTH 7447789004 Load Step Transient Response, 0mA to 500mA, VIN = 6V LOAD CURRENT (500mA/DIV) Load Step Transient Response, 0mA to 500mA, VIN = 24V LOAD CURRENT (500mA/DIV) VOUT (500mV/DIV) VOUT (500mV/DIV) INDUCTOR CURRENT (1A/DIV) INDUCTOR CURRENT (1A/DIV) 31151 TA07b 200µs/DIV Efficiency vs Load Current, PWM Mode 200µs/DIV Efficiency vs Load Current, Burst Mode Operation 100 90 90 80 70 EFFICIENCY (%) EFFICIENCY (%) 80 70 60 50 40 VIN = 6V VIN = 10V VIN = 24V VIN = 36V 30 20 0.01 0.1 LOAD CURRENT (A) 1 60 50 40 VIN = 6V VIN = 10V VIN = 24V VIN = 36V 30 20 0.1 31151 TA07d 38 31151 TA07c 1 10 LOAD CURRENT (mA) 100 31151 TA07e 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. DHD Package 16-Lead Plastic DFN (5mm × 4mm) (Reference LTC DWG # 05-08-1707) 0.70 ±0.05 4.50 ±0.05 3.10 ±0.05 2.44 ±0.05 (2 SIDES) PACKAGE OUTLINE 0.25 ± 0.05 0.50 BSC 4.34 ±0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 5.00 ±0.10 (2 SIDES) R = 0.20 TYP 4.00 ±0.10 (2 SIDES) 9 R = 0.115 TYP 0.40 ± 0.10 16 2.44 ± 0.10 (2 SIDES) PIN 1 TOP MARK (SEE NOTE 6) PIN 1 NOTCH 8 0.200 REF 1 0.25 ± 0.05 0.50 BSC 0.75 ±0.05 0.00 – 0.05 (DHD16) DFN 0504 4.34 ±0.10 (2 SIDES) BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WJGD-2) IN JEDEC PACKAGE OUTLINE MO-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 31151fb For more information www.linear.com/LTC3115-1 39 LTC3115-1 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. FE Package 20-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1663 Rev J) Exposed Pad Variation CA 6.40 – 6.60* (.252 – .260) 4.95 (.195) 4.95 (.195) 20 1918 17 16 15 14 13 12 11 6.60 ±0.10 4.50 ±0.10 2.74 (.108) 6.40 2.74 (.252) (.108) BSC SEE NOTE 4 0.45 ±0.05 1.05 ±0.10 0.65 BSC 1 2 3 4 5 6 7 8 9 10 RECOMMENDED SOLDER PAD LAYOUT 4.30 – 4.50* (.169 – .177) 0.09 – 0.20 (.0035 – .0079) 0.25 REF 0.50 – 0.75 (.020 – .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 40 1.20 (.047) MAX 0° – 8° 0.65 (.0256) BSC 0.195 – 0.30 (.0077 – .0118) TYP 0.05 – 0.15 (.002 – .006) FE20 (CA) TSSOP REV J 1012 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 31151fb For more information www.linear.com/LTC3115-1 LTC3115-1 Revision History REV DATE DESCRIPTION A 4/13 Clarified Efficiency graph 1 Clarified Absolute Maximum Rating table, Package Drawing and Order Information 2 B 5/15 PAGE NUMBER Clarified Electrical Characteristics table 3 Clarified Pin Functions 11 Clarified Compensation formula 25 Clarified Figure 3 17 Clarified GBUCK formula 22 Clarified Loop Compensation Example 26 Clarified PCB Layout Considerations Added LTC3114-1 to Related Parts list 30, 31, 32 42 31151fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more www.linear.com/LTC3115-1 tion that the interconnection of itsinformation circuits as described herein will not infringe on existing patent rights. 41 LTC3115-1 Typical Application 750kHz Automotive 5V Regulator with Cold Crank Capability L1 6.8µH CBST2 0.1µF CBST1 0.1µF BST1 SW1 AUTOMOTIVE 3.6V TO 40V CIN 10µF SW2 BST2 PVIN VIN PVOUT LTC3115-1 PWM/SYNC BURST PWM VC RUN OFF ON CO 47µF CFB RFB 1000pF 54.9k FB CIN: MURATA GRM55DR61H106K CO: MURATA GRM43ER60J476K D1: PANASONIC MA785 L1: SUMIDA CDRH8D43HPNP RT 47.5k PVCC VCC RT GND PGND 5V 1A CFF 33pF RTOP 1M RFF 42.2k RBOT 249k D1* C1 4.7µF 31151 TA08a *OPTIONAL-INSTALL D1 FOR IMPROVED EFFICIENCY AND LOWER INPUT OPERATING VOLTAGE Cold Crank Line Transient with 1A Load VIN (10V/DIV) 15ms FALL TIME EFFICIENCY (%) 80 VOUT (200mV/DIV) INDUCTOR CURRENT (1A/DIV) VOUT (200mV/DIV) 200ms/DIV 90 13.8V 6V 4.5V INDUCTOR CURRENT (1A/DIV) 100 40V 12V VIN (2V/DIV) Efficiency vs Load Current VIN = 12V Load Dump Line Transient with 1A Load 31151 TA08b 2ms/DIV 31151 TA08c 70 60 50 40 30 20 0.01 WITH BOOTSTRAP DIODE WITHOUT BOOTSTRAP DIODE 0.1 1 LOAD CURRENT (A) 31151 TA08d Related Parts PART NUMBER LTC3114-1 DESCRIPTION 1A (IOUT), 40V Synchronous Buck-Boost DC/DC Converter LTC3112 2.5A (IOUT), 15V Synchronous Buck-Boost DC/DC Converter LTC3113 3A (IOUT), 2MHz Synchronous Buck-Boost DC/DC Converter LTC3127 1A (IOUT), 1.2MHz Buck-Boost DC/DC Converter with Programmable Input Current Limit High Efficiency, Synchronous, 4-Switch Buck-Boost Controller LTC3789 LTC3785 LTC3534 ≤10A (IOUT), High Efficiency, 1MHz Synchronous, No RSENSE™ Buck-Boost Controller 7V, 500mA (IOUT), 1MHz Synchronous Buck-Boost DC/DC Converter 42 Linear Technology Corporation COMMENTS VIN = 2.2V to 40V, VOUT = 2.7V to 40V, IQ = 30µA, ISD < 3µA, DFN and TSSOP Packages VIN: 2.7V to 15V, VOUT : 2.5V to 14V, IQ = 40µA, ISD < 1µA, DFN and TSSOP Packages VIN: 1.8V to 5.5V, VOUT : 1.8V to 5.25V, IQ = 30µA, ISD < 1µA, DFN and TSSOP Packages 96% Efficiency VIN: 1.8V to 5.5V, VOUT : 1.8V to 5.25V, IQ = 35µA, ISD < 4µA, MSOP and DFN Packages VIN: 4V to 38V, VOUT : 0.8V to 38V, IQ = 3mA, ISD < 60µA, SSOP-28, QFN-28 Packages VIN: 2.7V to 10V, VOUT : 2.7V to 10V, IQ = 86µA, ISD < 15µA, QFN Package 94% Efficiency, VIN: 2.4V to 7V, VOUT : 1.8V to 7V, IQ = 25µA, ISD < 1µA, DFN and GN Packages 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC3115-1 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com/LTC3115-1 31151fb LT 0615 REV B • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2012