REVISIONS LTR DESCRIPTION A DATE (YR-MO-DA) APPROVED 14-12-09 Charles F. Saffle Update drawing to the latest requirements of MIL-PRF-38534. -sld REV SHEET REV A A A A A A SHEET 15 16 17 18 19 20 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil/ CHECKED BY Greg Cecil APPROVED BY Robert M. Heber MICROCIRCUIT, HYBRID, LINEAR, 48 CHANNEL, ANALOG MULTIPLEXER DRAWING APPROVAL DATE 09-06-03 REVISION LEVEL A SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 1 OF 5962-09203 20 5962-E087-15 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 Federal stock class designator \ RHA designator (see 1.2.1) 09203 01 Device type (see 1.2.2) / K Device class designator (see 1.2.3) X Case outline (see 1.2.4) C Lead finish (see 1.2.5) \/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 ACT8512 02 ACT8513 Circuit function 48 channel, voltage and current analog multiplexer, high impedance analog input with ESD protection 48 channel, analog multiplexer, high impedance analog input with ESD protection 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 2 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator X Terminals See figure 1 Package style 96 Ceramic quad flat pack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage between +VEE and GND ....................... Negative supply voltage between -VEE and GND....................... VREF to GND............................................................................... Digital input overvoltage range: VEN (pins 5, 6, 91, and 92) ...................................................... VA (pins 1, 3, 93, and 95)........................................................ VB (pins 2, 4, 94, and 96)........................................................ Analog input overvoltage range ................................................. Power dissipation (PD): Device type 01..................................................................... Device type 02..................................................................... Junction temperature (TJ) .......................................................... Thermal resistance junction-to-case (θJC) 2/ .............................. Storage temperature .................................................................. Lead temperature (soldering, 10 seconds) ................................ +20 V dc -20 V dc +7.5 V dc (< VREF + 0.5)V, (> GND - 0.5)V (< VREF + 0.5)V, (> GND - 0.5)V (< VREF + 0.5)V, (> GND - 0.5)V -18 V dc ≤ VS ≤ +18 V dc 135 mW 70 mW +150°C 10°C/W -55°C to +150°C +300°C 1.4 Recommended operating conditions. 3/ Positive supply voltage (+VEE) 4/ ............................................... Negative supply voltage (-VEE) 4/............................................... VREF 4/........................................................................................ Logic low level voltage (VAL) ...................................................... Logic high level voltage (VAH) .................................................... Case operating temperature range (TC)..................................... +15 V dc -15 V dc +5 V dc +0.8 V dc +4.0 V dc -55°C to +125°C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. 1/ 2/ 3/ 4/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Based on the maximum power dissipation spread over the multiplexer die. The devices cannot be operated with analog inputs from -15 V up to -5 V. Supply voltages must be applied in the following sequence -VEE, VREF, followed by +VEE. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 3 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http://quicksearch.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3. 3.2.4 Switching waveform(s). The switching waveform(s) shall be as specified on figure 4. 3.2.5 Block diagram(s). The block diagram(s) shall be as specified on figure 5. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Supply currents +IEE -IEE +ISBY -ISBY Address input currents IAL(0-3) IAH(0-3) Enable input current IENL(0-15) IENH(0-15) IENL(16-31) IENH(16-31) IENL(32-47) IENH(32-47) Group A subgroups Conditions 1/ 2/ 3/ -55°C ≤ TC ≤ +125°C unless otherwise specified VEN(0-63) = VA(0-3)A = VA(0-3)B = 0 1,2,3 VEN(0-63) = VA(0-3)A = VA(0-3)B = 0 1,2,3 VEN(0-63) = 4 V, VA(0-3)A = VA(0-3)B = 0 4/ 1,2,3 VEN(0-63) = 4 V, VA(0-3)A = VA(0-3)B = 0 4/ 1,2,3 VA = 0 V 2/ 1,2,3 VA = 5 V 2/ 1,2,3 VEN(0-15) = 0 V 1,2,3 VEN(0-15) = 5 V 1,2,3 VEN16-31) = 0 V 1,2,3 VEN(16-31) = 5 V 1,2,3 VEN(32-47) = 0 V 1,2,3 VEN(32-47) = 5 V 1,2,3 Device type Limits Unit Min Max 01 0 3 02 0 1.5 01 -3 0 02 -1.5 0 01 0 3 02 0 1.5 01 -3.0 0 02 -1.5 0 01 -6 6 02 -3 3 01 -6 6 02 -3 3 01 -2 2 02 -1 1 01 -2 2 02 -1 1 01 -2 2 02 -1 1 01 -2 2 02 -1 1 01 -2 2 02 -1 1 01 -2 2 02 -1 1 mA mA mA mA µA µA µA µA µA µA µA µA See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 5 TABLE I. Electrical performance characteristics - Continued. Test Symbol Positive input leakage current (CH0-CH47) Negative input leakage current (CH0-CH47) Output leakage current outputs (pins 25, 68 and 70) Currents (pins 26, 67, and 69 device type 01 only) Conditions 1/ 2/ 3/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups +ISOFFOUTPUT(ALL) VIN = +10 V, VEN = 4 V, output and all unused inputs = -10 V 5/ 6/ 1,2,3 +ISOFFCURRENT(ALL) VIN = +10 V, VEN = 4 V, output and all unused inputs = -10 V 5/ 6/ -ISOFFOUTPUT(ALL) Device type Limits Unit Min Max All -100 +1000 nA 1,2,3 All -100 +1000 nA VIN = -10 V, VEN = 4 V, output and all unused inputs = +10 V 5/ 6/ 1,2,3 All -100 +1000 nA -ISOFFCURRENT(ALL) VIN = -10 V, VEN = 4 V, output and all unused inputs = +10 V 5/ 6/ 1,2,3 All -100 +1000 nA +IDOFFOUTPUT(ALL) VIN = +10 V, VEN = 4 V, output and all unused inputs = -10 V 6/ 7/ 1,2,3 All -100 +100 nA +IDOFFCURRENT(ALL) VIN = +10 V, VEN = 4 V, output and all unused inputs = -10 V 6/ 7/ 1,2,3 All -100 +100 nA -IDOFFOUTPUT(ALL) VIN = -10 V, VEN = 4 V, output and all unused inputs = +10 V 6/ 7/ 1,2,3 All -100 +100 nA -IDOFFCURRENT(ALL) VIN = -10 V, VEN = 4 V, output and all unused inputs = +10 V 6/ 7/ 1,2,3 All -100 +100 nA See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Input clamped voltage (CH0-CH47) +VCLMP(0-47) -VCLMP(0-47) Switch ON resistance outputs (pins 25, 68, and 70) Switch ON resistance, current outputs (pins 26, 67, and 69) Switching tests Conditions 1/ 2/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Unit Max 18.0 23.0 2 18.0 23.5 3 17.5 22.5 -23.0 -18.0 2 -23.5 -18.0 3 -22.5 -17.5 All 1 VEN = 4 V, all unused inputs are open 6/ 8/ Limits Min 1 VEN = 4 V, all unused inputs are open 6/ 8/ Device type All V V RDS(ON)(0-47)A VIN = +15 V, VEN = 0.8 V, IOUT = -1 mA 5/ 6/ 9/ 1,2,3 All 200 1000 Ω RDS(ON)(0-47)B VIN = +5 V, VEN = 0.8 V, IOUT = -1 mA 5/ 6/ 9/ 1,2,3 All 200 1500 Ω RDS(ON)(0-47)C VIN = -5 V, VEN = 0.8 V, IOUT = +1 mA 5/ 6/ 9/ 1,2,3 All 200 2500 Ω RDS(ON)(0-47)A VIN = +15 V, VEN = 0.8 V, IOUT = -1 mA 5/ 6/ 9/ 1,2,3 01 200 1000 Ω RDS(ON)(0-47)B VIN = +5 V, VEN = 0.8 V, IOUT = -1 mA 5/ 6/ 9/ 1,2,3 01 200 1500 Ω RDS(ON)(0-47)C VIN = -5 V, VEN = 0.8 V, IOUT = +1 mA 5/ 6/ 9/ 1,2,3 01 200 2500 Ω tAHL RL = 10 kΩ, CL = 50 pF, See figure 4 9,10,11 All 10 1000 ns tALH RL = 10 kΩ, CL = 50 pF, See figure 4 9,10,11 All 10 1000 ns tONEN RL = 1 kΩ, CL = 50 pF, See figure 4 9,10,11 All 10 1000 ns tOFFEN RL = 1 kΩ, CL = 50 pF, See figure 4 9,10,11 All 10 1000 ns See footnotes at top of next page. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 7 TABLE I. Electrical performance characteristics - Continued. 1/ +VEE = +15 V dc, -VEE = -15 V dc, and VREF = +5 V dc, unless otherwise specified. Recommended power supply turn on sequence -VEE, VREF, followed by +VEE. 2/ Measure inputs sequentially. Ground all unused inputs. VA is the applied input voltage to the address lines A(0-3). VB is the applied input voltage to the address lines B(0-3). 3/ The device cannot be operated with analog inputs from -15 to -5 volts. 4/ If not tested, shall be guaranteed to the limits specified in table I. 5/ VIN is the applied input voltage to the input channels (CH0-CH47). 6/ VEN is the applied input voltage to the enable lines EN(0-15), EN(16-31), EN(32-47). 7/ VOUT is the applied input voltage to the output lines (OUTPUT(0-15), OUTPUT(16-31), OUTPUT(32-47), CURRENT(16-31), and CURRENT(32-47). (Current outputs for device type 01 only). 8/ Clamping test performed at ±25 V dc and a 2 kΩ limiting resistor between the input and the power supply. 9/ Negative current is the current flowing out of each of the pins. Positive current is the current flowing into each of the pins. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 8 Case outline X. FIGURE 1. Case outline(s). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 9 Case outline X - Continued. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 10 Case outline X - Continued. Inches Symbol Min Millimeters Max Min Max A .200 5.08 A1 .180 4.57 A2 .005 .011 0.13 0.28 b .0135 .0195 0.34 0.50 c .005 .008 0.13 0.20 D/E 1.287 1.313 32.69 33.35 D1 1.145 1.155 29.08 29.34 e .050 BSC 1.27 BSC F .200 TYP 5.08 TYP J .035 TYP 0.89 TYP L 2.490 2.510 L1 63.25 63.75 2.580 65.53 L2 1.700 1.740 43.18 44.20 L3 2.090 2.110 53.09 53.59 L4 .400 TYP 10.16 TYP N 96 96 S1 .030 TYP 0.76 TYP S2 .015 TYP 0.38 TYP NOTES: 1. Pin 1 is indicated by an ESD triangle on top of the package and by an index on the bottom of the package. 2. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 3. N equals 96, the total number of leads on the package. 4. Pin numbers are for reference only. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 11 Device type 01 Case outline Terminal number Terminal symbol Terminal number 1 A2 33 2 NC 3 A3 4 X Terminal symbol Terminal number Terminal symbol CH 11 65 CH 33 34 GND 66 CH 32 35 CH 12 67 OUTPUT I(32-47) NC 36 GND 68 OUTPUT V(32-47) 5 EN 0-15 37 CH 13 69 OUTPUT I(16-31) 6 GND 38 GND 70 OUTPUT V(16-31) 7 CH 0 39 CH 14 71 GND 8 GND 40 GND 72 GND 9 CH 1 41 CH 15 73 CH 31 10 GND 42 GND 74 CH 30 11 CH 2 43 NC 75 CH 29 12 GND 44 +VEE 76 CH 28 13 CH 3 45 NC 77 CH 27 14 GND 46 -VEE 78 CH 26 15 CH 4 47 NC 79 CH 25 16 GND 48 VREF 80 CH 24 17 CH 5 49 NC 81 CH 23 18 GND 50 Case GND 82 CH 22 19 CH 6 51 CH 47 83 CH 21 20 GND 52 CH 46 84 CH 20 21 CH 7 53 CH 45 85 CH 19 22 GND 54 CH 44 86 CH 18 23 GND 55 CH 43 87 CH 17 24 GND 56 CH 42 88 CH 16 25 OUTPUT V(0-15) 57 CH 41 89 GND 26 OUTPUT I(0-15) 58 CH 40 90 GND 27 CH 8 59 CH 39 91 EN 32-47 28 29 GND CH 9 60 61 CH 38 CH 37 92 93 EN 16-31 A0 30 31 GND CH 10 62 63 CH 36 CH 35 94 95 NC A1 32 GND 64 CH 34 96 NC NOTE: NC is a no connect pin. NC pins should be grounded to eliminate or minimize electrostatic discharge (ESD) or static buildup. FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 12 Device type 02 Case outline Terminal number Terminal symbol Terminal number 1 A2 33 2 NC 3 A3 4 X Terminal symbol Terminal number Terminal symbol CH 11 65 CH 33 34 GND 66 CH 32 35 CH 12 67 NC NC 36 GND 68 OUTPUT V(32-47) 5 EN 0-15 37 CH 13 69 NC 6 NC 38 GND 70 OUTPUT V(16-31) 7 CH 0 39 CH 14 71 GND 8 GND 40 GND 72 GND 9 CH 1 41 CH 15 73 CH 31 10 GND 42 GND 74 CH 30 11 CH 2 43 NC 75 CH 29 12 GND 44 +VEE 76 CH 28 13 CH 3 45 NC 77 CH 27 14 GND 46 -VEE 78 CH 26 15 CH 4 47 NC 79 CH 25 16 GND 48 VREF 80 CH 24 17 CH 5 49 NC 81 CH 23 18 GND 50 Case GND 82 CH 22 19 CH 6 51 CH 47 83 CH 21 20 GND 52 CH 46 84 CH 20 21 CH 7 53 CH 45 85 CH 19 22 GND 54 CH 44 86 CH 18 23 GND 55 CH 43 87 CH 17 24 GND 56 CH 42 88 CH 16 25 OUTPUT V(0-15) 57 CH 41 89 GND 26 NC 58 CH 40 90 GND 27 CH 8 59 CH 39 91 EN 32-47 28 29 GND CH 9 60 61 CH 38 CH 37 92 93 EN 16-31 A0 30 31 GND CH 10 62 63 CH 36 CH 35 94 95 NC A1 32 GND 64 CH 34 96 NC NOTE: NC is a no connect pin. NC pins should be grounded to eliminate or minimize electrostatic discharge (ESD) or static buildup. FIGURE 2. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 13 Truth table (CH 0 - CH 15) A3 X L L L L L L L L H H H H H H H H A2 X L L L L H H H H L L L L H H H H A1 X L L H H L L H H L L H H L L H H A0 X L H L H L H L H L H L H L H L H EN (0-15) H L L L L L L L L L L L L L L L L "ON" Channel 1/ None CH 0 CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8 CH 9 CH 10 CH 11 CH 12 CH 13 CH 14 CH 15 1/ Between CH 0-15 and OUTPUT (0-15) for device types 01and 02, CURRENT (0-15) for device type 01 only. Truth table (CH 16 - CH 31) A3 X L L L L L L L L H H H H H H H H A2 X L L L L H H H H L L L L H H H H A1 X L L H H L L H H L L H H L L H H A0 X L H L H L H L H L H L H L H L H EN (0-15) H L L L L L L L L L L L L L L L L "ON" Channel 1/ None CH 16 CH 17 CH 18 CH 19 CH 20 CH 21 CH 22 CH 23 CH 24 CH 25 CH 26 CH 27 CH 28 CH 29 CH 30 CH 31 1/ Between CH 16-31and OUTPUT (16-31) for device types 01and 02, CURRENT (16-31) for device types 01 only. FIGURE 3. Truth table(s). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 14 Truth table (CH 32 - CH 47) A3 X L L L L L L L L H H H H H H H H A2 X L L L L H H H H L L L L H H H H A1 X L L H H L L H H L L H H L L H H A0 X L H L H L H L H L H L H L H L H EN (0-15) H L L L L L L L L L L L L L L L L "ON" Channel 1/ None CH 32 CH 33 CH 34 CH 35 CH 36 CH 37 CH 38 CH 39 CH 40 CH 41 CH 42 CH 43 CH 44 CH 45 CH 46 CH 47 1/ Between CH 32-47and OUTPUT (32-47) for device types 01and 02, CURRENT (32-47) for device types 01 only. FIGURE 3. Truth tale(s) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 15 NOTE: f = 10 kHz, duty cycle = 50%. FIGURE 4. Switching test waveform(s). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 16 Device type 01 FIGURE 5. Block diagram. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 17 Device type 02 FIGURE 5. Block diagram - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 18 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1, 9 Final electrical parameters 1*, 2, 3, 9, 10, 11 Group A test requirements 1, 2, 3, 9, 10, 11 Group C end-point electrical parameters 1, 2, 3, 9, 10, 11 End-point electrical parameters for radiation hardness assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. b. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1015 of MIL-STD-883. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, 7, and 8 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 19 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-1081. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors, listed in MIL-HDBK103 and QML-38534, have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-09203 A REVISION LEVEL A SHEET 20 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 14-12-09 Approved sources of supply for SMD 5962-09203 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. 1/ 2/ Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-0920301KXC 5962-0920302KXC 88379 88379 ACT8512-201-1S ACT8513-201-1S The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its availability. Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number 88379 Vendor name and address Aeroflex Plainview Incorporated, (Aeroflex Microelectronic Solutions) 35 South Service Road Plainview, NY 11803 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.