94611

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
F
Figure 1; changed case outline M to be available in either a single or
dual cavity package. Added vendor CAGE code 0EU86 for device
types 05 through 10. -sld
99-04-22
K. A. Cottongim
G
Added device types 11 through 16.
99-08-18
Raymond Monnin
H
Add note to paragraph 1.2.2 and table I, conditions. Add thermal
resistance, junction-to-case (qJC) for all case outlines. Add case
outline 9.
00-04-06
Raymond Monnin
J
Table I, ICC change maximum limits and ISB change maximum limits.
Figure 1, case outline M, correct diagram adding "c" dimension, lead
thickness and change dimension A2 maximum from 0.020" to 0.025".
00-06-19
Raymond Monnin
K
Figure 1, case outline 9, minimum dimension for D2/E2, change 0.990
inches to 0.980 inches and 25.15 mm to 24.89 mm.
01-5-16
Raymond Monnin
L
Table I; Operating supply current (ICC) changed the maximum limit for
device types 9 and 15 at f = 50 MHz from 700 mA to 725 mA and for
device types 10 and 16 at f = 58.8 MHz from 700 mA to 750 mA. -sld
01-12-21
Raymond Monnin
M
Added device types 17 through 20. -sld
02-11-18
Raymond Monnin
N
Added case outline A. -sld
03-02-24
Raymond Monnin
P
Added case outline B. Added note to paragraph 1.2.4. -sld
03-12-19
Raymond Monnin
R
Table I; Changed the IOL from 8 mA to 6 mA for device types 07-10
and 13 -20 for the VOL test. Editorial changes throughout. -sld
04-05-03
Raymond Monnin
T
Updated drawing paragraphs. -sld
12-09-12
Charles F. Saffle
REV
SHEET
REV
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
SHEET
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
REV STATUS
REV
T
T
T
T
T
T
T
T
T
T
T
T
T
T
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PMIC N/A
PREPARED BY
Gary Zahn
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
CHECKED BY
Michael C. Jones
APPROVED BY
Kendall A. Cottongim
http://www.landandmaritime.dla.mil/
MICROCIRCUIT, HYBRID, MEMORY,
DIGITAL, 512K x 32-BIT, STATIC RANDOM
ACCESS MEMORY, CMOS
DRAWING APPROVAL DATE
95-11-13
REVISION LEVEL
T
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
1 OF
5962-94611
31
5962-E471-12
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
½
½
½
Federal
stock class
designator
\
½
½
½
RHA
designator
(see 1.2.1)
94611
01
½
½
½
Device
type
(see 1.2.2)
/
H
½
½
½
Device
class
designator
(see 1.2.3)
A
½
½
½
Case
outline
(see 1.2.4)
X
½
½
½
Lead
finish
(see 1.2.5)
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) shall identify the circuit function as follows:
Device type 1/ 2/
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
Generic number
Circuit function
S512K32-120
S512K32-100
S512K32-85
S512K32-70
S512K32-55
S512K32-45
S512K32-35
S512K32-25
S512K32-20
S512K32-17
S512K32-55
S512K32-45
S512K32-35
S512K32-25
S512K32-20
S512K32-17
S512K32-15
S512K32-12
S512K32-15
S512K32-12
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
512K X 32-BIT SRAM
Access time
120 ns
100 ns
85 ns
70 ns
55 ns
45 ns
35 ns
25 ns
20 ns
17 ns
55 ns
45 ns
35 ns
25 ns
20 ns
17 ns
15 ns
12 ns
15 ns
12 ns
1/ Due to the nature of the 4 transistor design of the die used in these device types, topologically pure testing is
important, particularly for high reliability applications. The device manufacturer should be consulted concerning
their testing methods and algorithms
2/ Device types 11 through 18 are not tested to data retention supply voltage (VDR) and data retention current (ICCDR1).
See table I.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
2
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
Device performance documentation
K
Highest reliability class available. This level is intended for use in space
applications.
H
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
G
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C, and D).
E
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
D
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
1.2.4 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows:
Outline letter
A
B
M 3/
T
U
X
Y
9 3/
Descriptive designator
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
Terminals
Package style
68
68
68
66
66
66
68
68
Co-fired ceramic, quad flatpack, single cavity
Ceramic, quad flatpack, single cavity
Co-fired ceramic, single/dual cavity, quad flatpack
Hex-in-line, single cavity, with standoffs
Hex-in-line, single cavity, with standoffs
Hex-in-line, single cavity, with standoffs
Ceramic, quad flatpack, single cavity
Ceramic, quad flatpack, single cavity
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
3/
Due to the short leads of case outlines M (single cavity) and case outline 9, caution should be taken if the system
application is to be used where extreme thermal transitions can occur. Case outline A can be used if longer leads are
necessary.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
3
1.3 Absolute maximum ratings. 4/
Supply voltage range (VCC) ........................................................
Signal voltage range (Vg) ...........................................................
Power dissipation (PD):
Device types 01-04 and 17-20 ...................................................
Device types 05, 06, 11, and 12 ................................................
Device types 07, 08, 13, and 14 ................................................
Device types 09, 10, 15, and 16 ................................................
Thermal resistance, junction-to-case (qJC):
Case outline A and M .............................................................
Case outlines T, U, and X.......................................................
Case outline Y ........................................................................
Case outlines B and 9 ............................................................
Storage temperature range ........................................................
Lead temperature (soldering, 10 seconds) ................................
Junction temperature (TJ) ..........................................................
-0.5 V dc to +7.0 V dc
-0.5 V dc to VCC +0.5 V dc
2.2 W
3.2 W
3.6 W
4.4 W
9.27°C/W
4.160°C/W
5.251°C/W
1.495°C/W
-65°C to +150°C
+300°C
+150°C
1.4 Recommended operating conditions.
Supply voltage range (VCC) ........................................................
Input low voltage range (VIL) ......................................................
Input high voltage range (VIH) ....................................................
Output low voltage, maximum (VOL) ...........................................
Output high voltage, minimum (VOH) ..........................................
Ambient operating temperature range (TA) ................................
+4.5 V dc to +5.5 V dc
-0.3 V dc to +0.8 V dc
+2.2 V dc to VCC +0.3 V dc
+0.4 V dc
+2.4 V dc
-55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.dla.mil/quicksearch/ or from the Standardization Document
Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
4/
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
4
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify, or optimize the tests and inspections herein, however, the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.
3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4 and 5.
3.2.5 Block diagram. The block diagram shall be as specified on figure 6.
3.2.6 Output load circuit. The output load circuit shall be as specified on figure 7.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime -VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
5
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/ 2/
-55°C £ TC £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
DC parameters
Operating supply current
ICC
CS = VIH, OE = VIH,
VCC = 5.5 V dc
3/
f = 5 MHz
f = 5 MHz
f = 18.2 MHz
f = 22.2 MHz
f = 28.6 MHz
f = 40 MHz
f = 50 MHz
f = 58.8 MHz
f = 66.67 MHz
f = 83.3 MHz
Standby current
ISB
CS = VIH, OE = VIH,
VCC = 5.5 V dc
f
f
f
f
f
f
f
f
f
f
1,2,3
01-04
05-16
05,11
06,12
07,13
08,14
09,15
10,16
17,19
18,20
200
600
625
635
650
675
725
750
200
250
mA
1,2,3
01-04
05-16
05,11
06,12
07,13
08,14
09,15
10,16
17-20
17-20
4
80
150
150
190
240
280
320
80
80
mA
3/
= 5 MHz
= 5 MHz
= 18.2 MHz
= 22.2 MHz
= 28.6 MHz
= 40 MHz
= 50 MHz
= 58.8 MHz
= 66.67 MHz
= 83.3 MHz
Input leakage current
ILI
VCC = 5.5 V dc,
VIN = GND or VCC
1,2,3
All
10
mA
Output leakage current
ILO
CS = VIH, OE = VIH,
VIN = GND or VCC
1,2,3
All
10
mA
Output low voltage
VOL
VCC = +4.5 V dc,
IOL = 2.1 mA
1,2,3
01-06,
11,12
0.4
V
07-10,
13-20
0.4
VCC = +4.5 V dc,
IOL = 6 mA
Output high voltage
VOH
VCC = +4.5 V dc,
IOH = -1.0 mA
1,2,3
VCC = +4.5 V dc,
IOH = -4.0 mA
01-06,
11,12
2.4
07-10,
13-20
2.4
V
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
6
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TC £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Unit
Min
Max
2.0
5.5
V
mA
Data retention characteristics
Data retention supply
voltage
VDR
Data retention current
ICCDR1
CS ³ VCC - 0.2 V dc
1,2,3
01-10
VCC = 3 V dc
1,2,3
01-04
1.6
05-10
28
19,20
32
Capacitance
OE capacitance 4/
COE
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
50
pF
WE 1-4 capacitance 4/
CWE
VOUT = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
20
pF
CS capacitance 4/
CCS
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
20
pF
D0-31 capacitance 4/
CI/O
VOUT = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
20
pF
A0-16 capacitance 4/
CAD
VOUT = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
50
pF
See 4.3.1c
7,8A,8B
All
See figure 4
9,10,11
01
02
03
04
05,11
06,12
07,13
08,14
09,15
10,16
17,19
18,20
Functional tests
Functional tests
Read cycle timing characteristics
Read cycle timing
tRC
120
100
85
70
55
45
35
25
20
17
15
12
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
7
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TC £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Read cycle timing characteristics - Continued.
Address access timing
tAA
See figure 4
9,10,11
01
02
03
04
05,11
06,12
07,13
08,14
09,15
10,16
17,19
18,20
120
100
85
70
55
45
35
25
20
17
15
12
Output hold from address
change
tOH
See figure 4
9,10,11
01-04
05-10
11-20
Chip select access timing
tACS
See figure 4
9,10,11
01
02
03
04
05,11
06,12
07,13
08,14
09,15
10,16
17,19
18,20
120
100
85
70
55
45
35
25
20
17
15
12
ns
Output enable to output
valid
tOE
See figure 4
9,10,11
01
02
03
04
05-07
11-13
08,14
09,15
10,16
17,19
18,20
60
50
40
35
25
25
12
10
9
8
7
ns
Chip select to output in
low impedence 4/
tCLZ
See figure 4
9,10,11
01,02
03,04
05-07
11-13
08-10
14-20
5
0
0
ns
ns
10
10
4
4
2
2
ns
See footnote at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
8
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TC £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Read cycle timing characteristics - Continued.
Output enable to output in
low impedence 4/
tOLZ
See figure 4
9,10,11
01-04
05-20
5
0
ns
Chip select high to output
in high impedence 4/
tCHZ
See figure 4
9,10,11
01,02
03,04
05,06
11,12
07,13
08-10
14-16
17,19
18,20
35
25
20
20
15
12
12
8
7
ns
Chip enable high to
output in high
impedence 4/
tOHZ
See figure 4
9,10,11
01,02
03,04
05,06
11,12
07,13
08-10
14-16
17,19
18,20
35
25
20
20
15
12
12
8
7
ns
See figure 5
9,10,11
01
02
03
04
05,11
06,12
07,13
08,14
09,15
10,16
17,19
18,20
Write cycle AC timing characteristics.
Write cycle time
tWC
120
100
85
70
55
45
35
25
20
17
15
12
ns
See footnote at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
9
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TC £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Write cycle AC timing characteristics - Continued.
Chip select to end of write
tCW
See figure 5
9,10,11
01
02
03
04
05,11
06,12
07,13
08,14
09,10
15,16
17,19
18,20
120
80
75
60
50
35
30
20
15
15
12
10
ns
Address valid to end of
write
tAW
See figure 5
9,10,11
01
02
03
04
05,11
06,12
07,13
08,14
09,10
15,16
17,19
18,20
100
80
75
60
50
35
30
20
15
15
12
10
ns
Data valid to end of write
tDW
See figure 5
9,10,11
01,02
03,04
05,06
11,12
07,13
08,14
09,10
15,16
17,19
18,20
40
30
25
25
20
15
12
12
10
8
ns
Address setup time
tAS
See figure 5
9,10,11
01-04
05-10
11-20
0
2
2
ns
See footnote at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
10
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TC £+125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Write cycle AC timing characteristics - Continued.
Write pulse width
tWP
See figure 5
9,10,11
01,02
03,04
05,11
06,12
07,13
08,14
09,10
15,16
17,19
18,20
Write enable to output in
high impedence 4/
tWHZ
See figure 5
9,10,11
01,02
03,04
05,06
11,12
07,13
08,14
09,15
10,16
17,19
18,20
Address hold time
tAH
See figure 5
9,10,11
01-06
11,12
07,08
13,14
09,15
17-20
10,16
5
5
2
2
1
1
0
ns
Output active from end of
write 4/
tOW
See figure 5
9,10,11
01-04
05-20
5
0
ns
Data hold time
tDH
See figure 5
9,10,11
All
0
ns
1/
2/
3/
4/
60
50
40
35
25
17
15
15
12
10
ns
35
25
20
20
15
13
11
9
8
7
ns
Due to the nature of the 4 transistor design of the die used in these device types, topologically pure testing is
important, particularly for high reliability applications. The device manufacturer should be consulted concerning
their testing methods and algorithms
Unless otherwise specified, the AC test conditions are as follows:
Input pulse levels: VIL = 0 V and VIH = 3.0 V
Input rise and fall times: 5 nanoseconds for device types 01-16 and 3 nanoseconds for device types 17-20.
Input and output timing reference level: 1.5 V ± 0.5 V
Output loading: see Figure 7.
Unless otherwise specified, the DC test conditions are as follows:
VIL = 0.3 V and VIH = VCC - 0.3 V
f = 1 / tAA.
Parameters shall be tested as part of device characterization and after design and process change. Parameters shall be
to the limits specified in table 1 for all lots not specifically tested.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
11
Case outline A.
FIGURE 1. Case outlines.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
12
Case outline A - Continued.
Symbol
Millimeters
Min
Inches
Max
A
Min
Max
5.10
A1
1.37
b
0.33
B
.200
.054
0.43
.013
0.25 TYP
.017
.010 TYP
c
0.23
0.30
.009
.012
D/E
24.9
25.4
.980
1.000
D1/E1
22.10
22.61
.870
.890
D2/E2
20.32 BSC
.800 BSC
e
1.27 BSC
.050 BSC
L
0.89
R
1.14
.035
0.25 TYP
.045
.010 TYP
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. Details of pin 1 identifier are optional, but must be located within the zone indicated.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
13
Case outline M.
FIGURE 1. Case outline(s).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
14
Case outline M - Continued.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
3.12
5.08
.123
.200
A1
2.30
4.72
.118
.186
A2
0.00
0.64
.000
.025
b
0.33
0.43
.013
.017
B
c
D/E
0.25 REF
0.15
0.30
.010 REF
.006
20.32 BSC
.012
.800 BSC
D1/E1
22.10
22.61
.870
.890
D2/E2
24.89
25.40
.980
1.000
D3/E3
23.77
24.28
.936
.956
e
1.27 BSC
R
0.13
L1
0.89
.050 BSC
.005
1.14
.035
.045
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. Pin numbers are for reference only.
3. Case outline M may either be a single cavity or a dual cavity package. Dimension A2 is measured between the
lowest horizontal plane of the package and the seating plane of the lead(s).
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
15
Case outline T.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
3.65
4.60
.144
.181
A1
0.64
0.89
.025
.035
øb
0.41
0.51
.016
.020
øb1
1.14
1.40
.045
.055
D/E
27.05
27.55
1.065
1.085
D1/E1
25.40 TYP
1.000 TYP
D2
15.24 TYP
.600 TYP
e
2.54 TYP
.100 TYP
L
3.68
3.94
.145
.155
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
16
Case outline U.
Symbol
A
A1
øb
øb1
D/E
D1/E1
D2
e
L
Millimeters
Min
Max
5.08
6.22
0.64
0.89
0.41
0.51
1.14
1.40
29.72
30.48
25.40 TYP
15.24 TYP
2.54 TYP
3.68
3.94
Inches
Min
Max
.200
.245
.025
.035
.016
.020
.045
.055
1.170
1.200
1.000 TYP
.600 TYP
.100 TYP
.145
.155
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
17
Case outline X.
Symbol
A
A1
øb
øb1
øb2
D/E
D1/E1
D2
D3/E3
e
L
Millimeters
Min
Max
4.83
6.22
0.64
0.89
0.41
0.51
1.14
1.40
1.65
1.91
34.80
35.56
25.40 TYP
15.24 TYP
34.04
34.29
2.54 TYP
3.68
3.94
Inches
Min
Max
.190
.245
.025
.035
.016
.020
.045
.055
.065
.075
1.370
1.400
1.000 TYP
.600 TYP
1.340
1.350
.100 TYP
.145
.155
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. Pin numbers are for reference only. Pin 1 is identified by .070 " square pad.
3. For solder lead finish, dimension fb will increase by +.003" (+0.008 mm).
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
18
Case outline Y.
Symbol
A
A1
A2
b
c
D/E
D1/E1
D2/E2
e
e1
j
k
S1
Millimeters
Min
Max
2.92
3.56
1.14
1.91
1.14
1.39
0.31
0.46
0.23
0.31
63.63
66.42
39.24
40.01
73.28
84.20
1.27 BSC
20.32 BSC
4.83
5.33
37.72
38.48
9.65 BSC
Inches
Min
Max
.115
.140
.045
.075
.045
.055
.012
.018
.009
.012
2.505
2.615
1.545
1.575
2.885
3.315
.050 BSC
.800 BSC
.190
.210
1.485
1.515
.380 BSC
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. Pin numbers are for reference only.
3. For solder lead finish, dimension b will increase by +.003" (+0.008 mm).
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
19
Case outline B.
Symbol
Millimeters
Min
Inches
Max
Min
Max
A
4.06
.160
A1
2.79
.110
A2
1.12
1.42
.044
.056
b
0.33
0.43
.013
.017
C
0.15
0.25
.006
.010
D/E
20.32 BSC
.800 BSC
D1/E1
23.65
24.10
.931
.949
D2/E2
24.89
25.40
.980
1.000
e
L1
1.27 BSC
0.51
1.14
.050 BSC
.020
.045
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall
rule.
2. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
20
Case outline 9.
Symbol
Millimeters
Min
A
Inches
Max
Min
3.56
A1
Max
.140
2.79
.110
A2
0.46
0.76
.018
.030
b
0.33
0.43
.013
.017
C
0.15
0.25
.006
.010
D/E
20.32 BSC
.800 BSC
D1/E1
23.65
24.10
.931
.949
D2/E2
24.89
25.40
.980
1.000
e
L1
1.27 BSC
0.51
1.14
.050 BSC
.020
.045
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall
rule.
2. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
21
Device
types
All
Device
types
All
Device
types
All
Device
types
All
Case
outlines
A, B, M, 9
Case
outlines
A, B, M, 9
Case
outlines
A, B, M, 9
Case
outlines
A, B, M, 9
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
1
GND
18
GND
35
OE
52
GND
2
CS3
19
I/O8
36
CS2
53
I/O23
3
A5
20
I/O9
37
A17
54
I/O22
4
A4
21
I/O10
38
WE 2
55
I/O21
5
A3
22
I/O11
39
WE 3
56
I/O20
6
A2
23
I/O12
40
WE 4
57
I/O19
7
A1
24
I/O13
41
A18
58
I/O18
8
A0
25
I/O14
42
NC
59
I/O17
9
NC
26
I/O15
43
NC
60
I/O16
10
I/O0
27
VCC
44
I/O31
61
VCC
11
I/O1
28
A11
45
I/O30
62
A10
12
I/O2
29
A12
46
I/O29
63
A9
13
I/O3
30
A13
47
I/O28
64
A8
14
I/O4
31
A14
48
I/O27
65
A7
15
I/O5
32
A15
49
I/O26
66
A6
16
I/O6
33
A16
50
I/O25
67
WE1
17
I/O7
34
CS1
51
I/O24
68
CS4
FIGURE 2. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
22
Device
types
All
Device
types
All
Device
types
All
Device
types
All
Case
outline
T, U, X
Case
outline
T, U, X
Case
outline
T, U, X
Case
outline
T, U, X
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
1
I/O8
18
A12
35
I/O25
52
WE 3
2
I/O9
19
VCC
36
I/O26
53
CS3
3
I/O10
20
CS1
37
A6
54
GND
4
A13
21
NC
38
A7
55
I/O19
5
A14
22
I/03
39
NC
56
I/O31
6
A15
23
I/015
40
A8
57
I/O30
7
A16
24
I/O14
41
A9
58
I/O29
8
A17
25
I/O13
42
I/O16
59
I/O28
9
I/O0
26
I/O12
43
I/O17
60
A0
10
I/O1
27
OE
44
I/O18
61
A1
11
I/O2
28
A18
45
VCC
62
A2
12
WE 2
29
WE1
46
CS4
63
I/O23
13
CS2
30
I/O7
47
WE 4
64
I/O22
14
GND
31
I/O6
48
I/O27
65
I/O21
15
I/O11
32
I/O5
49
A3
66
I/O20
16
A10
33
I/O4
50
A4
17
A11
34
I/O24
51
A5
FIGURE 2. Terminal connections - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
23
Device
types
All
Device
types
All
Device
types
All
Device
types
All
Case
outline
Y
Case
outline
Y
Case
outline
Y
Case
outline
Y
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
1
GND
18
GND
35
OE
52
GND
2
CS1
19
I/O8
36
CS4
53
I/O23
3
A5
20
I/O9
37
A17
54
I/O22
4
A4
21
I/O10
38
A18
55
I/O21
5
A3
22
I/O11
39
NC
56
I/O20
6
A2
23
I/O12
40
NC
57
I/O19
7
A1
24
I/O13
41
NC
58
I/O18
8
A0
25
I/O14
42
NC
59
I/O17
9
NC
26
I/O15
43
NC
60
I/O16
10
I/O0
27
VCC
44
I/O31
61
VCC
11
I/O1
28
A11
45
I/O30
62
A10
12
I/O2
29
A12
46
I/O29
63
A9
13
I/O3
30
A13
47
I/O28
64
A8
14
I/O4
31
A14
48
I/O27
65
A7
15
I/O5
32
A15
49
I/O26
66
A6
16
I/O6
33
A16
50
I/O25
67
WE
17
I/O7
34
CS2
51
I/O24
68
CS3
FIGURE 2. Terminal connections - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
24
CS
OE
WE
I/O
MODE
VIL
VIL
VIH
DOUT
Read
VIH
X
X
High Z
Standby
VIL
VIH
VIH
High Z
Output disable
VIL
VIH
VIL
DIN
Write
NOTES:
1. VIH = High logic level
2. VIL = Low logic level
3. X = Do not care (either high or low)
4. High Z = High impedance state
FIGURE 3. Truth table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
25
FIGURE 4. Read cycle timing diagram.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
26
FIGURE 5. Write cycle timing diagram.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
27
Case outlines A, B, M, T, U, X, and 9.
Case outline Y.
FIGURE 6. Block diagram(s).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
28
Parameter
Typical
Unit
Input pulse level
0 - 3.0
V
Input rise and fall
5
ns
Input and output reference level
1.5
V
Output load capacitance
50
pF
NOTES:
1. VZ is programmable from -2 V to +7 V
2. IOL and IOH are programmable from 0 to 16 mA.
3. Tester impedance is Z0 = 75 ohms.
4. VZ is typically the midpoint of VOL and VOH.
5. IOL and IOH are adjusted to simulate a typical resistive load circuit.
6. ATE tester includes jig capacitance.
FIGURE 7. Output load circuit.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
29
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group
A test table)
Interim electrical parameters
1,4,7,9
Final electrical parameters
1*,2,3,4,7,8A,8B,9,10,11
Group A test requirements
1,2,3,4,7,8A,8B,9,10,11
Group C end-point electrical
Parameters
1,2,3,4,7,8A,8B,9,10,11
End-point electrical parameters
for Radiation Hardness Assurance
(RHA) devices
Not applicable.
* PDA applies to subgroup 1.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a.
b.
Burn-in test, method 1015 of MIL-STD-883.
(1)
Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test
circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in method 1015 of MIL-STD-883.
(2)
TA as specified in accordance with table I of method 1015 of MIL-STD-883.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
Tests shall be as specified in table II herein.
b.
Subgroups 5 and 6 shall be omitted.
c.
Subgroups 7 and 8 shall include verification of the truth table on figure 3.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
30
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
End-point electrical parameters shall be as specified in table II herein.
b.
Steady-state life test, method 1005 of MIL-STD-883.
(1)
Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test
circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in method 1005 of MIL-STD-883.
(2)
TA as specified in accordance with table I of method 1005 of MIL-STD-883.
(3)
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation hardness assurance (RHA) insepction. RHA inspection is currently not applicable to this drawing.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list
will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices
(FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-0547.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors, listed in MIL-HDBK103 and QML-38534, have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have
agreed to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-94611
A
REVISION LEVEL
T
SHEET
31
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 12-09-12
Approved sources of supply for SMD 5962-94611 are listed below for immediate acquisition information only and shall be added
to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the
addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been
submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revisions
of MIL-HDBK-103 and QML-38534. DLA Land and Maritime maintains an online database of all current sources of supply at
http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9461101HMA
5962-9461101HMC
5962-9461101HXA
5962-9461101HXC
5962-9461101HYC
5962-9461101HUA
5962-9461101HUC
54230
54230
3/
3/
54230
54230
54230
WS512K32-120G2Q
WS512K32-120G2Q
WS512K32N-120H2Q
WS512K32N-120H2Q
WS512K32-120G4TQ
WS512K32N-120HQ
WS512K32N-120HQ
5962-9461102HMA
5962-9461102HMC
5962-9461102HXA
5962-9461102HXC
5962-9461102HYC
5962-9461102HUA
5962-9461102HUC
54230
54230
3/
3/
54230
54230
54230
WS512K32-100G2Q
WS512K32-100G2Q
WS512K32N-100H2Q
WS512K32N-100H2Q
WS512K32-100G4TQ
WS512K32N-100HQ
WS512K32N-100HQ
5962-9461103HMA
5962-9461103HMC
5962-9461103HXA
5962-9461103HXC
5962-9461103HYC
5962-9461103HUA
5962-9461103HUC
54230
54230
3/
3/
54230
54230
54230
WS512K32-85G2Q
WS512K32-85G2Q
WS512K32N-85H2Q
WS512K32N-85H2Q
WS512K32-85G4TQ
WS512K32N-85HQ
WS512K32N-85HQ
5962-9461104HMA
5962-9461104HMC
5962-9461104HXA
5962-9461104HXC
5962-9461104HYC
5962-9461104HUA
5962-9461104HUC
54230
54230
3/
3/
54230
54230
54230
WS512K32-70G2Q
WS512K32-70G2Q
WS512K32N-70H2Q
WS512K32N-70H2Q
WS512K32-70G4TQ
WS512K32N-70HQ
WS512K32N-70HQ
See footnotes at end of table.
1 of 9
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-09-12
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9461105HAA
5962-9461105HAC
5962-9461105HAA
5962-9461105HAC
5962-9461105HMA
5962-9461105HMC
5962-9461105HMA
5962-9461105HMC
5962-9461105HMA
5962-9461105HMC
5962-9461105HTA
5962-9461105HTC
5962-9461105HTA
5962-9461105HTC
5962-9461105HTA
5962-9461105HTC
5962-9461105HXA
5962-9461105HXC
5962-9461105HXA
5962-9461105HXC
5962-9461105HYA
5962-9461105HYC
5962-9461105HYC
5962-9461105H9A
5962-9461105H9C
5962-9461105H9A
5962-9461105H9C
5962-9461105HBA
5962-9461105HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
3/
3/
88379
88379
88379
88379
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-55L/883C
AS8S512K32Q1-55L/883C
WS512K32-55G2LQ
WS512K32-55G2LQ
AS8S512K32Q-55L/Q
AS8S512K32Q-55L/Q
WS512K32-55G2Q
WS512K32-55G2Q
ACT-S512K32N-055F2Q
ACT-S512K32N-055F2Q
AS8S512K32P-55L/Q
AS8S512K32P-55L/Q
WS512K32N-55H1Q
WS512K32N-55H1Q
ACT-S512K32N-055P7Q
ACT-S512K32N-055P7Q
WS512K32N-55H2Q
WS512K32N-55H2Q
ACT-S512K32N-055P1Q
ACT-S512K32N-055P1Q
ACT-S512K32N-055F1Q
ACT-S512K32N-055F1Q
WS512K32-55G4TQ
WS512K32-55G1UQ
WS512K32-55G1UQ
ACT-S512K32N-055F18Q
ACT-S512K32N-055F18Q
WS512K32-55G1TQ
WS512K32-55G1TQ
5962-9461106HAA
5962-9461106HAC
5962-9461106HAA
5962-9461106HAC
5962-9461106HMA
5962-9461106HMC
5962-9461106HMA
5962-9461106HMC
5962-9461106HMA
5962-9461106HMC
5962-9461106HTA
5962-9461106HTC
5962-9461106HTA
5962-9461106HTC
5962-9461106HTA
5962-9461106HTC
5962-9461106HXA
5962-9461106HXC
5962-9461106HXA
5962-9461106HXC
5962-9461106HYA
5962-9461106HYC
5962-9461106HYC
5962-9461106H9A
5962-9461106H9C
5962-9461106H9A
5962-9461106H9C
5962-9461106HBA
5962-9461106HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
3/
3/
88379
88379
88379
88379
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-45L/883C
AS8S512K32Q1-45L/883C
WS512K32-45G2LQ
WS512K32-45G2LQ
AS8S512K32Q-45L/Q
AS8S512K32Q-45L/Q
WS512K32-45G2Q
WS512K32-45G2Q
ACT-S512K32N-045F2Q
ACT-S512K32N-045F2Q
AS8S512K32P-45L/Q
AS8S512K32P-45L/Q
WS512K32N-45H1Q
WS512K32N-45H1Q
ACT-S512K32N-045P7Q
ACT-S512K32N-045P7Q
WS512K32N-45H2Q
WS512K32N-45H2Q
ACT-S512K32N-045P1Q
ACT-S512K32N-045P1Q
ACT-S512K32N-045F1Q
ACT-S512K32N-045F1Q
WS512K32-45G4TQ
WS512K32-45G1UQ
WS512K32-45G1UQ
ACT-S512K32N-045F18Q
ACT-S512K32N-045F18Q
WS512K32-45G1TQ
WS512K32-45G1TQ
See footnotes at end of table.
2 of 9
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-09-12
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9461107HAA
5962-9461107HAC
5962-9461107HAA
5962-9461107HAC
5962-9461107HMA
5962-9461107HMC
5962-9461107HMA
5962-9461107HMC
5962-9461107HMA
5962-9461107HMC
5962-9461107HTA
5962-9461107HTC
5962-9461107HTA
5962-9461107HTC
5962-9461107HTA
5962-9461107HTC
5962-9461107HXA
5962-9461107HXC
5962-9461107HXA
5962-9461107HXC
5962-9461107HYA
5962-9461107HYC
5962-9461107HYC
5962-9461107H9A
5962-9461107H9C
5962-9461107H9A
5962-9461107H9C
5962-9461107HBA
5962-9461107HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
3/
3/
88379
88379
88379
88379
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-35L/883C
AS8S512K32Q1-35L/883C
WS512K32-35G2LQ
WS512K32-35G2LQ
AS8S512K32Q-35L/Q
AS8S512K32Q-35L/Q
WS512K32-35G2Q
WS512K32-35G2Q
ACT-S512K32N-035F2Q
ACT-S512K32N-035F2Q
AS8S512K32P-35L/Q
AS8S512K32P-35L/Q
WS512K32N-35H1Q
WS512K32N-35H1Q
ACT-S512K32N-035P7Q
ACT-S512K32N-035P7Q
WS512K32N-35H2Q
WS512K32N-35H2Q
ACT-S512K32N-035P1Q
ACT-S512K32N-035P1Q
ACT-S512K32N-035F1Q
ACT-S512K32N-035F1Q
WS512K32-35G4TQ
WS512K32-35G1UQ
WS512K32-35G1UQ
ACT-S512K32N-035F18Q
ACT-S512K32N-035F18Q
WS512K32-35G1TQ
WS512K32-35G1TQ
5962-9461108HAA
5962-9461108HAC
5962-9461108HAA
5962-9461108HAC
5962-9461108HMA
5962-9461108HMC
5962-9461108HMA
5962-9461108HMC
5962-9461108HMA
5962-9461108HMC
5962-9461108HTA
5962-9461108HTC
5962-9461108HTA
5962-9461108HTC
5962-9461108HTA
5962-9461108HTC
5962-9461108HXA
5962-9461108HXC
5962-9461108HXA
5962-9461108HXC
5962-9461108HYA
5962-9461108HYC
5962-9461108HYC
5962-9461108H9A
5962-9461108H9C
5962-9461108H9A
5962-9461108H9C
5962-9461108HBA
5962-9461108HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
3/
3/
88379
88379
88379
88379
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-25L/883C
AS8S512K32Q1-25L/883C
WS512K32-25G2LQ
WS512K32-25G2LQ
AS8S512K32Q-25L/Q
AS8S512K32Q-25L/Q
WS512K32-25G2Q
WS512K32-25G2Q
ACT-S512K32N-025F2Q
ACT-S512K32N-025F2Q
AS8S512K32P-25L/Q
AS8S512K32P-25L/Q
WS512K32N-25H1Q
WS512K32N-25H1Q
ACT-S512K32N-025P7Q
ACT-S512K32N-025P7Q
WS512K32N-25H2Q
WS512K32N-25H2Q
ACT-S512K32N-025P1Q
ACT-S512K32N-025P1Q
ACT-S512K32N-025F1Q
ACT-S512K32N-025F1Q
WS512K32-25G4TQ
WS512K32-25G1UQ
WS512K32-25G1UQ
ACT-S512K32N-025F18Q
ACT-S512K32N-025F18Q
WS512K32-25G1TQ
WS512K32-25G1TQ
See footnotes at end of table.
3 of 9
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-09-12
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9461109HAA
5962-9461109HAC
5962-9461109HAA
5962-9461109HAC
5962-9461109HMA
5962-9461109HMC
5962-9461109HMA
5962-9461109HMC
5962-9461109HMA
5962-9461109HMC
5962-9461109HTA
5962-9461109HTC
5962-9461109HTA
5962-9461109HTC
5962-9461109HTA
5962-9461109HTC
5962-9461109HXA
5962-9461109HXC
5962-9461109HXA
5962-9461109HXC
5962-9461109HYA
5962-9461109HYC
5962-9461109HYC
5962-9461109H9A
5962-9461109H9C
5962-9461109H9A
5962-9461109H9C
5962-9461109HBA
5962-9461109HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
3/
3/
88379
88379
88379
88379
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-20L/883C
AS8S512K32Q1-20L/883C
WS512K32-20G2LQ
WS512K32-20G2LQ
AS8S512K32Q-20L/Q
AS8S512K32Q-20L/Q
WS512K32-20G2Q
WS512K32-20G2Q
ACT-S512K32N-020F2Q
ACT-S512K32N-020F2Q
AS8S512K32P-20L/Q
AS8S512K32P-20L/Q
WS512K32N-20H1Q
WS512K32N-20H1Q
ACT-S512K32N-020P7Q
ACT-S512K32N-020P7Q
WS512K32N-20H2Q
WS512K32N-20H2Q
ACT-S512K32N-020P1Q
ACT-S512K32N-020P1Q
ACT-S512K32N-020F1Q
ACT-S512K32N-020F1Q
WS512K32-20G4TQ
WS512K32-20G1UQ
WS512K32-20G1UQ
ACT-S512K32N-020F18Q
ACT-S512K32N-020F18Q
WS512K32-20G1TQ
WS512K32-20G1TQ
5962-9461110HAA
5962-9461110HAC
5962-9461110HAA
5962-9461110HAC
5962-9461110HMA
5962-9461110HMC
5962-9461110HMA
5962-9461110HMC
5962-9461110HMA
5962-9461110HMC
5962-9461110HTA
5962-9461110HTC
5962-9461110HTA
5962-9461110HTC
5962-9461110HTA
5962-9461110HTC
5962-9461110HXA
5962-9461110HXC
5962-9461110HXA
5962-9461110HXC
5962-9461110HYA
5962-9461110HYC
5962-9461110HYC
5962-9461110H9A
5962-9461110H9C
5962-9461110H9A
5962-9461110H9C
5962-9461110HBA
5962-9461110HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
3/
3/
88379
88379
88379
88379
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-17L/883C
AS8S512K32Q1-17L/883C
WS512K32-17G2LQ
WS512K32-17G2LQ
AS8S512K32Q-17L/Q
AS8S512K32Q-17L/Q
WS512K32-17G2Q
WS512K32-17G2Q
ACT-S512K32N-017F2Q
ACT-S512K32N-017F2Q
AS8S512K32P-17L/Q
AS8S512K32P-17L/Q
WS512K32N-17H1Q
WS512K32N-17H1Q
ACT-S512K32N-017P7Q
ACT-S512K32N-017P7Q
WS512K32N-17H2Q
WS512K32N-17H2Q
ACT-S512K32N-017P1Q
ACT-S512K32N-017P1Q
ACT-S512K32N-017F1Q
ACT-S512K32N-017F1Q
WS512K32-17G4TQ
WS512K32-17G1UQ
WS512K32-17G1UQ
ACT-S512K32N-017F18Q
ACT-S512K32N-017F18Q
WS512K32-17G1TQ
WS512K32-17G1TQ
See footnotes at end of table.
4 of 9
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-09-12
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9461111HAA
5962-9461111HAC
5962-9461111HAA
5962-9461111HAC
5962-9461111HMA
5962-9461111HMC
5962-9461111HMA
5962-9461111HMC
5962-9461111HTA
5962-9461111HTC
5962-9461111HTA
5962-9461111HTC
5962-9461111HTA
5962-9461111HTC
5962-9461111HXA
5962-9461111HXC
5962-9461111HYC
5962-9461111H9A
5962-9461111H9C
5962-9461111H9A
5962-9461111H9C
5962-9461111HBA
5962-9461111HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
3/
3/
3/
3/
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-55/883C
AS8S512K32Q1-55/883C
WS512K32D-55G2LQ
WS512K32D-55G2LQ
AS8S512K32Q-55/Q
AS8S512K32Q-55/Q
WS512K32D-55G2Q
WS512K32D-55G2Q
AS8S512K32P-55/Q
AS8S512K32P-55/Q
WS512K32ND-55H1Q
WS512K32ND-55H1Q
ACT-S512K32D-055P7Q
ACT-S512K32D-055P7Q
WS512K32ND-55H2Q
WS512K32ND-55H2Q
WS512K32D-55G4TQ
WS512K32D-55G1UQ
WS512K32D-55G1UQ
ACT-S512K32D-055F18Q
ACT-S512K32D-055F18Q
WS512K32D-55G1TQ
WS512K32D-55G1TQ
5962-9461112HAA
5962-9461112HAC
5962-9461112HAA
5962-9461112HAC
5962-9461112HMA
5962-9461112HMC
5962-9461112HMA
5962-9461112HMC
5962-9461112HTA
5962-9461112HTC
5962-9461112HTA
5962-9461112HTC
5962-9461112HTA
5962-9461112HTC
5962-9461112HXA
5962-9461112HXC
5962-9461112HYC
5962-9461112H9A
5962-9461112H9C
5962-9461112H9A
5962-9461112H9C
5962-9461112HBA
5962-9461112HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
3/
3/
3/
3/
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-45/883C
AS8S512K32Q1-45/883C
WS512K32D-45G2LQ
WS512K32D-45G2LQ
AS8S512K32Q-45/Q
AS8S512K32Q-45/Q
WS512K32D-45G2Q
WS512K32D-45G2Q
AS8S512K32P-45/Q
AS8S512K32P-45/Q
WS512K32ND-45H1Q
WS512K32ND-45H1Q
ACT-S512K32D-045P7Q
ACT-S512K32D-045P7Q
WS512K32ND-45H2Q
WS512K32ND-45H2Q
WS512K32D-45G4TQ
WS512K32D-45G1UQ
WS512K32D-45G1UQ
ACT-S512K32D-045F18Q
ACT-S512K32D-045F18Q
WS512K32D-45G1TQ
WS512K32D-45G1TQ
See footnotes at end of table.
5 of 9
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-09-12
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9461113HAA
5962-9461113HAC
5962-9461113HAA
5962-9461113HAC
5962-9461113HMA
5962-9461113HMC
5962-9461113HMA
5962-9461113HMC
5962-9461113HTA
5962-9461113HTC
5962-9461113HTA
5962-9461113HTC
5962-9461113HTA
5962-9461113HTC
5962-9461113HXA
5962-9461113HXC
5962-9461113HYC
5962-9461113H9A
5962-9461113H9C
5962-9461113H9A
5962-9461113H9C
5962-9461113HBA
5962-9461113HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
3/
3/
3/
3/
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-35/883C
AS8S512K32Q1-35/883C
WS512K32D-35G2LQ
WS512K32D-35G2LQ
AS8S512K32Q-35/Q
AS8S512K32Q-35/Q
WS512K32D-35G2Q
WS512K32D-35G2Q
AS8S512K32P-35/Q
AS8S512K32P-35/Q
WS512K32ND-35H1Q
WS512K32ND-35H1Q
ACT-S512K32D-035P7Q
ACT-S512K32D-035P7Q
WS512K32ND-35H2Q
WS512K32ND-35H2Q
WS512K32D-35G4TQ
WS512K32D-35G1UQ
WS512K32D-35G1UQ
ACT-S512K32D-035F18Q
ACT-S512K32D-035F18Q
WS512K32D-35G1TQ
WS512K32D-35G1TQ
5962-9461114HAA
5962-9461114HAC
5962-9461114HAA
5962-9461114HAC
5962-9461114HMA
5962-9461114HMC
5962-9461114HMA
5962-9461114HMC
5962-9461114HTA
5962-9461114HTC
5962-9461114HTA
5962-9461114HTC
5962-9461114HTA
5962-9461114HTC
5962-9461114HXA
5962-9461114HXC
5962-9461114HYC
5962-9461114H9A
5962-9461114H9C
5962-9461114H9A
5962-9461114H9C
5962-9461114HBA
5962-9461114HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
3/
3/
3/
3/
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-25/883C
AS8S512K32Q1-25/883C
WS512K32D-25G2LQ
WS512K32D-25G2LQ
AS8S512K32Q-25/Q
AS8S512K32Q-25/Q
WS512K32D-25G2Q
WS512K32D-25G2Q
AS8S512K32P-25/Q
AS8S512K32P-25/Q
WS512K32ND-25H1Q
WS512K32ND-25H1Q
ACT-S512K32D-055P7Q
ACT-S512K32D-055P7Q
WS512K32ND-25H2Q
WS512K32ND-25H2Q
WS512K32D-25G4TQ
WS512K32D-25G1UQ
WS512K32D-25G1UQ
ACT-S512K32D-025F18Q
ACT-S512K32D-025F18Q
WS512K32D-25G1TQ
WS512K32D-25G1TQ
See footnotes at end of table.
6 of 9
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-09-12
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9461115HAA
5962-9461115HAC
5962-9461115HAA
5962-9461115HAC
5962-9461115HMA
5962-9461115HMC
5962-9461115HMA
5962-9461115HMC
5962-9461115HTA
5962-9461115HTC
5962-9461115HTA
5962-9461115HTC
5962-9461115HTA
5962-9461115HTC
5962-9461115HXA
5962-9461115HXC
5962-9461115HYC
5962-9461115H9A
5962-9461115H9C
5962-9461115H9A
5962-9461115H9C
5962-9461115HBA
5962-9461115HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
3/
3/
3/
3/
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-20/883C
AS8S512K32Q1-20/883C
WS512K32D-20G2LQ
WS512K32D-20G2LQ
AS8S512K32Q-20/Q
AS8S512K32Q-20/Q
WS512K32D-20G2Q
WS512K32D-20G2Q
AS8S512K32P-20/Q
AS8S512K32P-20/Q
WS512K32ND-20H1Q
WS512K32ND-20H1Q
ACT-S512K32D-055P7Q
ACT-S512K32D-055P7Q
WS512K32ND-20H2Q
WS512K32ND-20H2Q
WS512K32D-20G4TQ
WS512K32D-20G1UQ
WS512K32D-20G1UQ
ACT-S512K32D-020F18Q
ACT-S512K32D-020F18Q
WS512K32D-20G1TQ
WS512K32D-20G1TQ
5962-9461116HAA
5962-9461116HAC
5962-9461116HAA
5962-9461116HAC
5962-9461116HMA
5962-9461116HMC
5962-9461116HMA
5962-9461116HMC
5962-9461116HTA
5962-9461116HTC
5962-9461116HTA
5962-9461116HTC
5962-9461116HTA
5962-9461116HTC
5962-9461116HXA
5962-9461116HXC
5962-9461116HYC
5962-9461116H9A
5962-9461116H9C
5962-9461116H9A
5962-9461116H9C
5962-9461116HBA
5962-9461116HBC
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
3/
3/
3/
3/
54230
54230
54230
3/
3/
54230
54230
AS8S512K32Q1-17/883C
AS8S512K32Q1-17/883C
WS512K32D-17G2LQ
WS512K32D-17G2LQ
AS8S512K32Q-17/Q
AS8S512K32Q-17/Q
WS512K32D-17G2Q
WS512K32D-17G2Q
AS8S512K32P-17/Q
AS8S512K32P-17/Q
WS512K32ND-17H1Q
WS512K32ND-17H1Q
ACT-S512K32D-055P7Q
ACT-S512K32D-055P7Q
WS512K32ND-17H2Q
WS512K32ND-17H2Q
WS512K32D-17G4TQ
WS512K32D-17G1UQ
WS512K32D-17G1UQ
ACT-S512K32D-017F18Q
ACT-S512K32D-017F18Q
WS512K32D-17G1TQ
WS512K32D-17G1TQ
5962-9461117HAA
5962-9461117HAC
5962-9461117HAA
5962-9461117HAC
5962-9461117HMA
5962-9461117HMA
5962-9461117HMC
5962-9461117HMC
5962-9461117HTA
5962-9461117HTA
5962-9461117HTC
5962-9461117HTC
5962-9461117H9A
5962-9461117H9C
5962-9461117HBA
5962-9461117HBC
0EU86
0EU86
54230
54230
0EU86
54230
0EU86
54230
0EU86
54230
0EU86
54230
54230
54230
54230
54230
AS8S512K32Q1-15/883C
AS8S512K32Q1-15/883C
WS512K32D-15G2LQ
WS512K32D-15G2LQ
AS8S512K32Q-15/Q
WS512K32D-15G2Q
AS8S512K32Q-15/Q
WS512K32D-15G2Q
AS8S512K32P-15/Q
WS512K32ND-15H1Q
AS8S512K32P-15/Q
WS512K32ND-15H1Q
WS512K32D-15G1UQ
WS512K32D-15G1UQ
WS512K32D-15G1TQ
WS512K32D-15G1TQ
See footnotes at end of table.
7 of 9
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-09-12
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9461118HAA
5962-9461118HAC
5962-9461118HAA
5962-9461118HAC
5962-9461118HMA
5962-9461118HMA
5962-9461118HMC
5962-9461118HMC
5962-9461118HTA
5962-9461118HTA
5962-9461118HTC
5962-9461118HTC
5962-9461118H9A
5962-9461118H9C
5962-9461118HBA
5962-9461118HBC
0EU86
0EU86
54230
54230
0EU86
54230
0EU86
54230
0EU86
54230
0EU86
54230
54230
52230
54230
54230
AS8S512K32Q1-12/883C
AS8S512K32Q1-12/883C
WS512K32D-12G2LQ
WS512K32D-12G2LQ
AS8S512K32Q-12/Q
WS512K32D-12G2Q
AS8S512K32Q-12/Q
WS512K32D-12G2Q
AS8S512K32P-12/Q
WS512K32ND-12H1Q
AS8S512K32P-12/Q
WS512K32ND-12H1Q
WS512K32D-12G1UQ
WS512K32D-12G1UQ
WS512K32D-12G1TQ
WS512K32D-12G1TQ
5962-9461119HAA
5962-9461119HAC
5962-9461119HAA
5962-9461119HAC
5962-9461119HMA
5962-9461119HMA
5962-9461119HMC
5962-9461119HMC
5962-9461119HTA
5962-9461119HTA
5962-9461119HTC
5962-9461119HTC
5962-9461119H9A
5962-9461119H9C
5962-9461119HBA
5962-9461119HBC
0EU86
0EU86
54230
54230
0EU86
54230
0EU86
54230
0EU86
54230
0EU86
54230
54230
54230
54230
54230
AS8S512K32Q1-15L/883C
AS8S512K32Q1-15L/883C
WS512K32-15G2LQ
WS512K32-15G2LQ
AS8S512K32Q-15L/Q
WS512K32-15G2Q
AS8S512K32Q-15L/Q
WS512K32-15G2Q
AS8S512K32P-15L/Q
WS512K32N-15H1Q
AS8S512K32P-15L/Q
WS512K32N-15H1Q
WS512K32-15G1UQ
WS512K32-15G1UQ
WS512K32D-15G1TQ
WS512K32D-15G1TQ
5962-9461120HAA
5962-9461120HAC
5962-9461120HAA
5962-9461120HAC
5962-9461120HMA
5962-9461120HMA
5962-9461120HMC
5962-9461120HMC
5962-9461120HTA
5962-9461120HTA
5962-9461120HTC
5962-9461120HTC
5962-9461120H9A
5962-9461120H9C
5962-9461120HBA
5962-9461120HBC
0EU86
0EU86
54230
54230
0EU86
54230
0EU86
54230
0EU86
54230
0EU86
54230
54230
54230
54230
54230
AS8S512K32Q1-12L/883C
AS8S512K32Q1-12L/883C
WS512K32-12G2LQ
WS512K32-12G2LQ
AS8S512K32Q-12L/Q
WS512K32-12G2Q
AS8S512K32Q-12L/Q
WS512K32-12G2Q
AS8S512K32P-12L/Q
WS512K32N-12H1Q
AS8S512K32P-12L/Q
WS512K32N-12H1Q
WS512K32-12G1UQ
WS512K32-12G1UQ
WS512K32-12G1TQ
WS512K32-12G1TQ
1/ The lead finish shown for each PIN, representing a hermetic package, is the most readily available from the
manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine
availability.
2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the
performance requirements of this drawing.
3/
This part is no longer available.
8 of 9
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-09-12
Vendor CAGE
number
Vendor name
and address
0EU86
Austin Semiconductor, Incorporated
DBA Micross Components
8701 Cross Park Drive
Suite 105
Austin, TX 78754
54230
White Electronic Designs Corporation
3601 East University Drive
Phoenix, AZ 85034
88379
Aeroflex Plainview Incorporated,
(Aeroflex Microelectronic Solutions)
35 South Service Road
Plainview, NY 11803
The information contained herein is disseminated for convenience only and the Government
assumes no liability whatsoever for any inaccuracies in this information bulletin.
9 of 9