REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Page 2, 1.3: Change θJA. Page 6, 4.2a(2) and 4.3.2b(2): Change TA to TC for burn-in and life test. Pages 7 and 8, table I: Add end-point electricals for VTH. Add footnote 2/. 86-10-30 W. Heckman B Made technical changes to table I. Updated drawing format with editorial changes. Added device types 02 through 07. Added cases Y,Z, U, and T. Changed to reflect MIL-H-38534 processing. Device type 01 inactive for new design. Added current CAGE code 67268 to sheet 1. 90-02-09 W. Heckman C Add device type 08. Made technical changes to table I. Change dimensions for case outline Y. Change dimensions for case outline U. Editorial changes throughout. 94-01-14 K. Cottongim D Changes in accordance with NOR 5962-R170-95. 95-07-12 Kendall A. Cottongim E Update drawing boilerplate to most current format. 02-02-25 Raymond Monnin F Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add TC. 04-12-02 Raymond Monnin G Table I, Total current, ICC1-SB, ICC1-25, ICC1-50, ICC1-100 for device type 06; change the maximum limit from 30 mA to 60 mA. (4 places) gz 07-05-10 Robert M. Heber H Added device type 09. Updated boilerplate paragraphs. -sld 10-01-15 Charles F. Saffle J Updated drawing paragraphs. -sld 11-09-01 Charles F. Saffle K Figure 2; Corrected terminal symbols for pins 15 and 16 from "RX Data out and RX Data out" to "RX Data in and RX Data in". -sld 13-01-30 Charles F. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED CURRENT CAGE CODE 67268 REV SHEET REV K K K K K K K SHEET 15 16 17 18 19 20 21 REV STATUS OF SHEETS REV K K K K K K K K K K K K K K SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PREPARED BY PMIC N/A Donald R. Osborne STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 CHECKED BY http://www.landandmaritime.dla.mil/ D. A. DiCenzo APPROVED BY N. A. Hauck DRAWING APPROVAL DATE MICROCIRCUIT, HYBRID, DIGITAL, SINGLE CHANNEL, DRIVER-RECEIVER 86-07-30 AMSC N/A REVISION LEVEL K SIZE CAGE CODE A 14933 SHEET DSCC FORM 2233 APR 97 5962-86049 1 OF 21 5962-E208-13 1. SCOPE 1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with MIL-PRF-38534 and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2 PIN. The PIN shall be as shown in the following example: 5962-86049 Drawing number 01 Device type (see 1.2.1) X Case outline (see 1.2.2) A Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows: Device type 01 02 03 1/ 04 1/ 05 06 07 08 09 Generic number Circuit function BUS-63105 BUS-63105II, BUS-63106II ARX2402 ARX3402 CT-1487M, BUS-8553, BUS-63100 NHI-1509 FC155361 FC155362 ACT4402 Single channel driver-receiver Low power, single channel driver-receiver Single channel driver-receiver Low power, single channel driver-receiver Single channel driver-receiver Single channel driver-receiver Single channel driver-receiver Single channel driver-receiver Low power, single channel driver-receiver 1.2.2 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals T U X Y Z See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 24 24 24 24 24 Package style Flat package Dual-in-line package Dual-in-line package Dual-in-line package Dual-in-line package 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1/ The device types 03 and 04 are no longer available. Device type 09 may be evaluated as a possible substitute. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 2 1.3 Absolute maximum ratings. 1/ Supply voltage range: VCC (device types 01, 03, 04, 05, 06, 07, 08, and 09) .............. VEE (device types 01, 02, 03, 04, 05, 07, 08, and 09) .............. VCC1 ......................................................................................... Logic input voltage range .......................................................... Receiver differential voltage ..................................................... Receiver common mode voltage range ..................................... Driver peak output current ......................................................... Power dissipation (PD) at +125°C: Device types 01, 05, 07, and 08 ............................................. Device types 02 and 09 .......................................................... Device type 03 ....................................................................... Device type 04 ........................................................................ Device type 06 ....................................................................... Storage temperature range ........................................................ Lead temperature (soldering, 10 seconds) ................................ Junction temperature (TJ) ......................................................... Thermal resistance, junction-to-case (θJC): Device types 01, 06, 07, and 08 ............................................. Device types 02 and 09 .......................................................... Device type 03 ....................................................................... Device type 04 ........................................................................ Device type 05 ........................................................................ Thermal resistance, junction to ambient (θJA): Device types 01, 06, 07, 08, and 09 ....................................... Device type 02 ......................................................................... Device type 03 ....................................................................... Device type 04 ........................................................................ Device type 05 ........................................................................ -0.3 V dc to +18 V dc +0.3 V dc to -18 V dc -0.3 V dc to +7 V dc -0.3 V dc to VCC1 40 Vp-p -10 V dc to +10 V dc 200 mA 4W 2.5 W 2.2 W 1.6 W 0.585 W -65°C to +150°C +300°C +160°C 8.8°C/W 7.0°C/W 47.2°C/W 88°C/W 60°C/W 38.8°C/W 37.0°C/W 77.2°C/W 110°C/W 80°C/W 1.4 Recommended operating conditions. Supply voltage range: VCC (device types 01, 03, 04, 05, 06, 07, 08, and 09) .............. VEE (device types 01, 02, 03, 04, 05, 07, 08, and 09) .............. VCC1 ......................................................................................... Logic input voltage range .......................................................... Receiver differential voltage ...................................................... Receiver common mode voltage range ..................................... Driver peak output current: Device types 01, 03, 04, 05, 06, 07, and 08 ........................... Device type 02 ......................................................................... Serial data rate ......................................................................... Junction temperature (TJ) ......................................................... Case operating temperature range (TC) ................................... 1/ +14.25 V dc to +15.75 V dc -14.25 V dc to -15.75 V dc +4.5 V dc to +5.5 V dc 0 V dc to +5.0 V dc 30 Vp-p -5.0 V dc to +5.0 V dc 180 mA 160 mA 1.0 MHz maximum +150°C maximum -55°C to +125°C Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https://assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device class H shall be in accordance with MILPRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Waveforms. The waveforms shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 4 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. b. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA or TC as specified in accordance with table I of method 1015 of MIL-STD-883. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 5 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max Receiver Input level VI Differential input, pin 15 to pin 16 2/ 4,5,6 All 40 Input common mode voltage range VICM Independent of xfmr or in accordance with MIL-HDBK-1553 2/ 4,5,6 All -5 Output low voltage VOL IOL = 16 mA 1,2,3 IOL = 4 mA Output high voltage VOH IOH = -0.4 mA 1,2,3 Vp-p +5 V(pk) 01,02 0.5 V 03,04,05, 06,07,08, 09 0.5 01,03,04, 05,06,07, 08,09 2.5 02 2.4 V Transmitter Input voltage low VIL 3/ 1,2,3 All Input voltage high VIH 3/ 1,2,3 All 2 Input current low IIL VIL = 0.4 V 1,2,3 01,03,05, 07,08 -1.6 02 -0.72 04,06,09 -0.4 Input current high IIH VIH = 2.7 V 1,2,3 0.7 V V mA 0.04 0.04 01,03,04, 05,06,07, 08,09 mA 02 -0.72 0.04 6 9 Vp-p 10 mVp-p Output voltage VO Across 35Ω load 1,2,3 All Output noise voltage VON Across 35Ω load 4,5,6 All See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max Receiver strobe Input voltage low VSIL 3/ 1,2,3 All Input voltage high VSIH 3/, in accordance with MIL-HDBK-1553 2/ 1,2,3 All 2 Input current low ISIL VIL = 0.4 V 1,2,3 01,05, 07,08 -1.6 02 -0.72 03,06 -0.8 04,09 -0.4 Input current high ISIH VIH = 2.7 V 1,2,3 0.7 V mA 0.4 0.04 01,03,04, 05,06,07, 08,09 02 V -0.72 mA 0.04 Transmitter inhibit Input voltage low VIIL 3/ 1,2,3 All Input voltage high VIIH 3/ 1,2,3 All 2 Input current low IIIL VSIL = 0.4 V 1,2,3 01,03,05, 07,08 -1.6 02 -0.72 04,06,09 -0.4 Input current high IIIH VSIH = 2.7 V 1,2,3 0.7 V mA 0.04 0.04 01,03,04, 05,06,07, 08,09 02 V -0.72 mA 0.04 See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 7 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max Power supply Total current ICC-SB (Standby mode) 1,2,3 01,07,08 03 04,09 05,06 50 40 1 25 mA IEE-SB (Standby mode) 1,2,3 01,07,08 02 03 04,09 05 50 35 30 16.5 35 mA ICC1-SB (Standby mode) 1,2,3 01,07,08 02,05 03 04,09 06 35 45 20 30 60 mA ICC-25 (25% duty cycle into 35Ω load) 1,2,3 01,07,08 03 05,06 04,09 65 90 75 55 mA IEE-25 (25% duty cycle into 35Ω load) 1,2,3 01,07,08 02 2/ 95 80 mA 03 04,09 05 30 21 35 01,07,08 02 2/ 35 45 05 03 04,09 06 45 20 30 60 ICC1-25 (25% duty cycle into 35Ω load) 1,2,3 mA ICC-50 (50% duty cycle into 35Ω load) 1,2,3 01,07,08 03 04,09 05,06 140 140 110 130 mA IEE-50 (50% duty cycle into 35Ω load) 1,2,3 01,07,08 02 03 04,09 05 50 130 30 25 35 mA See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 8 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max Power supply - Continued. Total current ICC1-50 (50% duty cycle into 35Ω load) 4,5,6 01,07,08 02,05 03 04,09 06 35 45 20 30 60 mA ICC-100 (100% duty cycle into 35Ω load) 1,2,3 01,07,08 03 04,06,09 05 240 240 220 235 mA IEE-100 (100% duty cycle into 35Ω load) 1,2,3 01,07,08 02 2/ 50 225 mA 03,04,09 05 30 35 01,07,08 02 2/ 35 45 05 03 04,09 06 45 20 30 60 ICC1-100 (100% duty cycle into 35Ω load) 1,2,3 mA Receiver Input resistance RIN 1 MHz sine wave 2/ 4,5,6 All Input capacitance CIN 1 MHz sine wave 2/ 4 All Threshold voltage VTH 4/ 1,2,3, 01,02,03, 04,05,06, 09 0.56 1.05 07,08 0.80 1.2 01,03,04, 05,06,07, 08,09 0.50 1.1 02 0.56 1.0 1,2,3 4/ Group C end point electricals 7 kΩ 5 pF Vp-p See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 9 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max Transmitter Output resistance (transmitter off) ROUT 1 MHz sine wave 2/ 4,5,6 All 10 Output capacitance (transmitter off) COUT 1 MHz sine wave 2/ 4 All 5 pF Output offset voltage VOS 2/ 5/ 4,5,6 All ±90 mV pk Peak amplitude variation AV 2/ 6/ 4,5,6 01,03,04, 05,06,07, 08,09 +15 % Delay time, input to output tDR Delay time from differential input zero crossing to DATA or DATA 2/ (see figure 3) 9,10,11 All 400 ns Strobe delay tDS Delay time from strobe rising or falling edge to DATA or DATA 2/ (see figure 3) 9,10,11 01,02,03, 05,06,07, 08 200 ns 04,09 250 -15 kΩ Receiver Transmitter Rise time tR Fall time tF Delay time tDT Inhibit delay inhibiting Inhibit delay active tDI-H tDI-L Output load = 35Ω (see figure 3) Output load = 35Ω (see figure 3) 2/ Output load = 35Ω (see figure 3) 2/ Output load = 35Ω (see figure 3) 2/ 9,10,11 9,10,11 9,10,11 9,10,11 All 100 300 All 100 300 01,02,05, 07,08 250 04,09 350 03,06 150 01,02,04, 05,07,08, 09 450 03,06 200 01,02,04, 05,07,08, 09 250 03,06 100 ns ns ns ns See notes on top of next page. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 10 TABLE I. Electrical performance characteristics - Continued. 1/ VCC = +15 V, for device types 01, 03, 04, 05, 06, 07, 08, and 09, VEE = -15 V for device types 01, 02, 03, 04, 05, 07, 08, and 09, VCC1 = +5 V. 2/ This parameter is tested initially and after any process or design change which may affect this parameter. 3/ These parameters are tested on a go-no-go basis in conjunction with other measured parameters and are not directly testable. 4/ Threshold is measured in direct coupled mode including the transformer. Threshold is the maximum level on the BUS at which there are no pulses on either receiver output. Divide by 1.4 to obtain threshold in transformer coupled mode. Add 0.14 V in direct coupled mode or 0.10 V in transformer coupled mode to obtain threshold at which no errors are observed when receiver is used with 15530 CMOS Manchester encoder-decoder. 5/ Measured across 35Ω load, 2.5 µs after parity bit mid-bit zero crossing of a 660 microseconds message. 6/ Measured across 35Ω load, variation of average peak amplitude. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 11 Case outline T. (Device types 02 and 06) Inches .002 .003 .010 .015 .072 .085 .100 .175 .500 .775 1.100 1.275 mm 0.05 0.08 0.25 0.38 1.83 2.16 2.54 4.45 12.70 19.68 27.94 32.39 FIGURE 1. Case outline(s). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 12 Case outline U. (Device type 04) Inches .002 .005 .010 .017 .100 .150 .200 .600 .630 1.100 1.250 mm 0.05 0.13 0.25 0.43 2.54 3.81 5.08 15.24 16.00 27.94 31.75 FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 13 Case outline X. (Device types 01, 05, 07, 08, and 09) Inches .004 .007 .015 .016 .019 .020 .030 .050 mm 0.10 0.18 0.38 0.41 0.48 0.50 0.76 1.27 Inches .100 .125 .170 .200 .600 .805 1.100 1.400 mm 2.54 3.18 4.32 5.08 15.24 20.45 27.94 35.56 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Lead identification numbers are for reference only. 4. Lead spacing dimensions apply only at seating plane. 5. The total number of terminals are 24. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 14 Case outline Y. (Device types 03, 05, and 06) Inches .002 .003 .010 .018 .085 .100 .175 .215 .600 .775 1.100 1.275 mm 0.05 0.07 0.25 0.45 2.15 2.54 4.44 5.45 15.24 19.68 27.94 32.38 FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 15 Case outline Z. (Device type 02) Inches .002 .010 .015 .018 .025 .040 .100 .155 .230 .600 .790 1.100 1.295 NOTE: Lead cluster to be centralized within ±0.010 of outline dimensions. mm 0.05 0.25 0.38 0.46 0.64 1.02 2.54 3.94 5.84 15.24 20.07 27.94 32.89 FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 16 Device types All Case outlines T, U, X, Y, and Z. Terminal number Terminal symbol Terminal number Terminal symbol 1 TX Data Out 13 VCC 1/ 2 TX Data Out 14 No connection 3 Ground 1/ 15 RX Data In 4 No connection 16 RX Data In 5 No connection 17 No connection 6 No connection 18 Ground 1/ 7 RX Data Out 19 VEE 2/ 8 Strobe 20 VCC1 9 Ground 1/ 21 TX Inhibit 10 RX Data Out 22 TX Data In 11 No connection 23 TX Data In 12 No connection 24 No connection 1/ GND pins should all be connected externally. Pin 13 is +15 V dc for device types 01, 03, 04, 05, 06, 07, 08, and 09 only, no connection for device type 02. 2/ Pin 19 for device type 06 only, no connection. FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 17 Device types 01 through 07, and 09. FIGURE 3. Waveforms. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 18 Device type 08. FIGURE 3. Waveforms - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 19 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters --- Final electrical parameters 1*,2,3,4,5,6,9,10,11 Group A test requirements 1,2,3,4,5,6,9,10,11 Group C end-point electrical parameters 1,2,3 End-point electrical parameters for radiation hardness assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 7 and 8 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA or TC as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 20 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-8108. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 43218-3990, or telephone (614) 692-1081. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime -VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-86049 A REVISION LEVEL K SHEET 21 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 13-01-30 Approved sources of supply for SMD 5962-86049 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-8604901XA 3/ BUS-63105 5962-8604902TC 5962-8604902TC 5962-8604902TC 3/ 3/ 3/ BUS-63106II-110 BUS-63106II-130 BUS-63106II-601 5962-8604902ZA 5962-8604902ZA 5962-8604902ZA 19645 19645 19645 BUS-63105II-140 BUS-63105II-150 BUS-63105II-634 5962-8604902ZC 5962-8604902ZC 5962-8604902ZC 19645 19645 19645 BUS-63105II-110 BUS-63105II-130 BUS-63105II-633 5962-8604903YA 5962-8604903YC 3/ 3/ ARX2402 ARX2402 5962-8604904UA 5962-8604904UC 3/ 3/ ARX3402 ARX3402 5962-8604905XA 5962-8604905XA 3/ 3/ BUS-8553-140 BUS-8553-150 5962-8604905XC 5962-8604905XC 3/ 3/ BUS-8553-110 BUS-8553-130 5962-8604905YA 3/ CT1487M 5962-8604905YA 5962-8604905YA 3/ 3/ BUS-8553-140 BUS-8553-150 5962-8604905YC 5962-8604905YC 3/ 3/ BUS-8553-110 BUS-8553-130 5962-8604906TA 5962-8604906TC 3/ 3/ NHI-1509FP NHI-1509FP 5962-8604906YA 5962-8604906YC 3/ 3/ NHI-1509 NHI-1509 5962-8604907XA 5962-8604907XC U4388 U4388 FC155361 FC155361 5962-8604908XA 5962-8604908XC U4388 U4388 FC155362 FC155362 5962-8604909UA 5962-8604909UC 88379 88379 ACT4402-001-2 ACT4402-001-1 See footnotes at end of table. 1 of 2 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 13-01-30 1/ 2/ 3/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its availability. Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Not available from an approved source. Vendor CAGE number Vendor name and address U4388 RF2M Microelectronics Limited Trading AS API Technologies Corporation DBA C-MAC Microtechnology Fenner Road, South Denes Great Yarmouth NR30 3PX Norfolk Great Britain 19645 Data Device Corporation 105 Wilbur Place Bohemia, NY 11716-2482 57363 National Hybrid Incorporated 2200 Smithtown Avenue Ronkonkoma, NY 11779-7329 88379 Aeroflex Plainview Incorporated, (Aeroflex Microelectronic Solutions) 35 South Service Road Plainview, NY 11803 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 2 of 2