95613

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
Added device types 05 through 10. Added case outlines X, Z, and T.
Redrew entire document.
96-08-23
K. A. Cottongim
B
Added device types 11 through 13. Added case outline U.
96-10-22
K. A. Cottongim
C
Made changes in accordance with NOR 5962-R289-97. -sld
97-04-28
K. A. Cottongim
D
Table I; Changed the max limit for the operating supply current test
ICC for device types 05-10 from 130 mA to 135 mA. Table I; Changed
the max limit for data retention current (ICCDR1) for device types 05-10
from 3.0 mA to 7.0 mA. Add vendor cage 88379 for device types 11,
12, and 13 per letter dated 1 MAY 1997. -sld
98-02-18
E
Add device type 14.
98-06-22
K. A. Cottongim
F
Changes to case outlines U and X.
99-04-30
K. A. Cottongim
G
Add: note to paragraph 1.2.2 and table I, conditions. Add device types
15 through 27, case outlines M, N, and 9, vendor CAGE code 0EU86,
condition D to paragraphs 4.2.a.1 and 4.3.3.b.1. Changes to table I
and dimensions to case outlines T, U, Y, and Z. Table I, add note 3 to
CIN and COUT.
01-02-08
Raymond Monnin
H
Table I; Changed the IOL from 8 mA to 6 mA for device types 07-14
and 21-27 for the VOL test. Added device types 28, 29, and 30.
Editorial changes throughout. -sld
04-05-28
Raymond Monnin
J
Add new case outline 7. gc
08-08-04
Robert M. Heber
K
Updated drawing paragraphs. -sld
12-04-02
Charles F. Saffle
REV
SHEET
REV
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
SHEET
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
REV STATUS
REV
K
K
K
K
K
K
K
K
K
K
K
K
K
K
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PMIC N/A
PREPARED BY
Steve L. Duncan
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
CHECKED BY
Michael C. Jones
APPROVED BY
Kendall A. Cottongim
http://www.landandmaritime.dla.mil/
MICROCIRCUIT, MEMORY, DIGITAL, SRAM,
512K x 8-BIT, MONOLITHIC SILICON
DRAWING APPROVAL DATE
95-11-07
REVISION LEVEL
K
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
1 OF
5962-95613
32
5962-E296-12
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
½
½
½
Federal
stock class
designator
\
½
½
½
RHA
designator
(see 1.2.1)
95613
01
½
½
½
Device
type
(see 1.2.2)
H
½
½
½
Device
class
designator
(see 1.2.3)
/
X
½
½
½
Case
outline
(see 1.2.4)
X
½
½
½
Lead
finish
(see 1.2.5)
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) shall identify the circuit function as follows:
Device type 1/ 2/
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Generic number
Circuit function
AS5C4009-120, WMS512K8-120
AS5C4009-100, WMS512K8-100
AS5C4009-85, WMS512K8-85
AS5C4009-70, WMS512K8-70
ACT-S512K8N-055, AS5C512K8-55, WMS512K8-55
ACT-S512K8N-045, AS5C512K8-45, WMS512K8-45
ACT-S512K8N-035, AS5C512K8-35, WMS512K8-35
ACT-S512K8N-025, AS5C512K8-25, WMS512K8-25
ACT-S512K8N-020, AS5C512K8-20, WMS512K8-20
ACT-S512K8N-017, AS5C512K8-17, WMS512K8-17
ACT-S512K8M-045, AS5C512K8-45, WMS512K8M-45
ACT-S512K8M-035, AS5C512K8-35, WMS512K8M-35
ACT-S512K8M-025, AS5C512K8-25, WMS512K8M-25
WMS512K8-15
AS5C4009-120L, WMS512K8L-120
AS5C4009-100L, WMS512K8L-100
AS5C4009-85L, WMS512K8L-85
AS5C4009-70L, WMS512K8L-70
AS5C512K8-55L, WMS512K8L-55
AS5C512K8-45L, WMS512K8L-45
AS5C512K8-35L, WMS512K8L-35
AS5C512K8-25L, WMS512K8L-25
AS5C512K8-20L, WMS512K8L-20
AS5C512K8-17L, WMS512K8L-17
AS5C512K8-45L
AS5C512K8-35L
AS5C512K8-25L
AS5C512K-12L, WMS512K8L-12
AS5C512K-12, WMS512K8-12
WMS512K8U-12
Data retention Access time
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
512K x 8 bit SRAM
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
120 ns
100 ns
85 ns
70 ns
55 ns
45 ns
35 ns
25 ns
20 ns
17 ns
45 ns
35 ns
25 ns
15 ns
120 ns
100 ns
85 ns
70 ns
55 ns
45 ns
35 ns
25 ns
20 ns
17 ns
45 ns
35 ns
25 ns
12 ns
12 ns
12 ns
1/ Due to the nature of the 4 transistor design of the die used in these device types, topologically pure testing is important,
particularly for high reliability applications. The device manufacturer should be consulted concerning their testing methods
and algorithms.
2/ Device types and case outlines may be similar to the device types and case outlines listed on SMD 5962-95600.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
2
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
Device performance documentation
K
Highest reliability class available. This level is intended for use in space
applications.
H
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
G
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C and D).
E
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
D
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
1.2.4 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
M
N
T
U
X
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
32
36
32
36
36
Y
Z
9
7
See figure 1
See figure 1
See figure 1
See figure 1
32
36
32
36
Package style
Leadless chip carrier, ceramic
Leadless chip carrier, ceramic
SOJ, ceramic, evolutionary pinout
Flat pack, ceramic, with or without pedestal
Flat pack, ceramic, with non-conductive tie
bar, with or without pedestal
DIP, ceramic, single cavity
SOJ, ceramic
Flat pack, ceramic
SOJ, ceramic
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Supply voltage range (VCC) .......................................................
Signal voltage range (Vg) .........................................................
Power dissipation (PD) ..............................................................
Storage temperature range .......................................................
Lead temperature (soldering, 10 seconds) ...............................
Junction temperature (TJ) .........................................................
1/
-0.5 V dc to +7.0 V dc
-0.5 V dc to VCC + 0.5 V dc
1.1 W maximum
-65°C to +150°C
+300°C
150°C
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
3
1.4 Recommended operating conditions.
Supply voltage range (VCC) .......................................................
Input low voltage range (VIL) .....................................................
Input high voltage range (VIH) ...................................................
Output low voltage, maximum (VOL) ..........................................
Output high voltage, minimum (VOH) .........................................
Ambient operating temperature range (TA) ...............................
+4.5 V dc to +5.5 V dc
-0.3 V dc to +0.8 V dc
+2.2 V dc to VCC +0.3 V dc
+0.4 V dc
+2.4 V dc
-55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
4
3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4 and 5.
3.2.5 Block diagram. The block diagram shall be as specified on figure 6.
3.2.6 Output load circuit. The output load circuit used to test product shall be equivalent to the circuit specified on figure 7.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.6 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime -VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a.
b.
Burn-in test, method 1015 of MIL-STD-883.
(1)
Test condition B or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1015 of MIL-STD-883.
(2)
TA as specified in accordance with table 1 of method 1015 of MIL-STD-883.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
5
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/ 2/
-55°C £ TA £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
DC parameters
Operating supply current
Standby current
ICC
ISB
CS = VIL, OE = VIH,
f = 5 MHz, VCC = 5.5 V dc
1,2,3
CS = VIH, OE = VIH,
f = 5 MHz, VCC = 5.5 V dc
1,2,3
01-04,
15-18
50
05-10,
19-24
160
11-14,
25-27
200
28,29,
30
90
01-04,
15-18,
30
1
05-10,
19-24
20
11-14,
25-29
30
mA
mA
Input leakage current
ILI
VIN = GND or VCC,
VCC = 5.5 V dc
1,2,3
All
10
mA
Output leakage current
ILO
CS = VIH, OE = VIH,
VOUT = GND or VCC
1,2,3
All
10
mA
Output low voltage
VOL
VCC = +4.5 V dc, IOL = 2.1 mA
1,2,3
01-06,
15-20
0.4
V
07-14,
21-30
0.4
VCC = +4.5 V dc, IOL = 6.0 mA
Output high voltage
VOH
VCC = +4.5 V dc, IOH = -1 mA
1,2,3
VCC = +4.5 V dc, IOH = -4 mA
01-06,
15-20
2.4
07-14,
21-30
2.4
V
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
6
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TA £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £+5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Data retention characteristics.
Data retention supply
voltage
VDR
CS ³ VCC -0.2
1,2,3
Data retention current
ICCDR1
VCC = 2 V dc
1,2,3
VCC = 3 V dc
1,2,3
All
5.5
V
15-18,30
0.2
mA
19-27
2.6
28
7.0
01-04,
15-18,30
05-10,
14
2.0
mA
0.4
7.0
19-27
5.1
11,12,13,
28
10.0
Capacitance
Input capacitance 3/
CIN
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
Case outlines M, T, Y, and 9.
4
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
Case outlines N, U, X, and Z.
Output capacitance 3/
COUT
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
Case outlines M, T, Y, and 9.
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
Case outlines N, U, X, and Z.
4
01-04,
15-18
12
05-14,
19-30
20
01-04,
15-18
20
05-14,
19-30
12
01-04,
15-18
12
05-14,
19-30
20
01-04,
15-18
20
05-14,
19-30
12
pF
pF
pF
pF
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
7
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TA £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Functional tests.
Functional tests
See 4.3.1c
7,8A,8B
All
See figure 4
9,10,11
01,15
02,16
03,17
04,18
05,19
06,11,
20,25
07,12,
21,26
08,13,
22,27
09,23
10,24
14
28,29,30
Read cycle AC timing characteristics.
Read cycle timing
Address access timing
Output hold from address
change
tRC
tAC
tOH
See figure 4
9,10,11
See figure 4
9,10,11
120
100
85
70
55
45
ns
35
25
20
17
15
12
01,15
02,16
03,17
04,18
05,19
06,11,
20,25
07,12,
21,26
08,13,
22,27
09,23
10,24
14
28,29,30
120
100
85
70
55
45
ns
35
25
20
17
15
12
01-04,
14,
15-18
5
05-13,
19-30
0
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
8
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TA £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Read cycle AC timing characteristics - Continued.
Chip select access timing
Output enable to output
valid
Chip select to output in low
impedance 3/
tACS
tOE
tCLZ
See figure 4
9,10,11
See figure 4
9,10,11
See figure 4
9,10,11
01,15
02,16
03,17
04,18
05,19
06,11,
20,25
07,12,
21,26
08,13,
22,27
09,23
10,24
14
28,29,30
120
100
85
70
55
45
01,15
02,16
03,17
04,11,
18,25
05-07,
12,19,
20,21,
26
08,13,
22,27
09,23
10,24
14
28,29,30
60
50
40
35
ns
35
25
20
17
15
12
ns
25
12
10
9
8
7
01-04,
15-18
10
05-07,
11,12,
19-21,
25,26
4
08-10,
13,14,
22-24,
27-30
2
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
9
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TA £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Read cycle AC timing characteristics - Continued.
Output enable to output in
low impedance 3/
Chip select high to output in
high impedance 3/
Output enable high to
output in high
impedance 3/
tOLZ
tCHZ
tOHZ
See figure 4
9,10,11
See figure 4
9,10,11
See figure 4
9,10,11
01-04,
15-18
5
05-14,
19-30
0
ns
01,02,
15,16
35
03,04,
17,18
25
05,06,
19,20
20
07,11,
12,21,
25,26
15
08,13,
22,27
12
09,23
10
10,24
9
14
8
28,29,30
6.5
01,02,
15,16
03,04,
17,18
05,06,
19,20
07,11,
12,21,
25,26
08,13,
22,27
09,23
10,24
14
28,29,30
35
ns
ns
25
20
15
12
10
9
8
6.5
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
10
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TA £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Write cycle AC timing characteristics.
Write cycle timing
Chip select to end of write
tWC
tCW
See figure 5
9,10,11
See figure 5
9,10,11
01,15
120
02,16
100
03,17
85
04,18
70
05,19
55
06,11,
20,25
45
07,12,
21,26
35
08,13,
22,27
25
09,23
20
10,24
17
14
15
28,29,30
12
01,15
02,16
03,17
04,18
05,19
06,11,
20,25
07,12,
21,26
08,22
09,10,
23,24
13,27
14
28,29,30
100
80
75
60
50
35
ns
ns
25
15
14
17
13
12
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
11
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TA £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Write cycle AC timing characteristics - Continued.
Address valid to end of write
Data valid to end of write
Address setup time
tAW
tDW
tAS
See figure 5
9,10,11
See figure 5
9,10,11
See figure 5
9,10,11
01,15
100
02,16
80
03,17
75
04,18
60
05,19
50
06,11,
20,25
35
07,12,
21,26
25
08,22
15
09,10,
23,24
14
13,27
17
14
13
28,29,30
12
01,02,
15,16
03, 04,
11,17,
18,25
05,06,
19,20
07,12,
21,26
08,09,
22,23
10,24
13,27
14
28,29,30
40
9
15
8
6.5
All
2
ns
ns
30
25
20
10
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
12
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TA £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Write cycle AC timing characteristics - Continued.
Write pulse width
Write enable to output in
high impedance 3/
tWP
tWHZ
See figure 5
9,10,11
See figure 5
9,10,11
01,02,
15,16
60
03, 04,
17,18
50
05,19
40
06,11,
20,25
35
07,12,
21,26
25
08,22
15
09,10,
23,24
14
13,27
17
14
13
28,29,30
12
ns
01,02,
15,16
03-05,
17-19
06,20
07,21
35
11,12,
25,26
08,13,22
,27
09,10,
23,24
14
28,29,30
15
ns
25
15
20
10
9
8
6.5
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
13
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C £ TA £ +125°C
VSS = 0 V dc
+4.5 V dc £ VCC £ +5.5 V dc
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
Write cycyle AC timing characterisitics - Continued.
Address hold time
Output active from end of
write 3/
Data hold time
1/
2/
3/
tAH
tOW
tDH
See figure 5
9,10,11
See figure 5
9,10,11
See figure 5
9,10,11
01-06,
15-20
5
07-14,
21-30
0
01-06,
15-20
5
07-14,
21-30
0
All
ns
ns
0
ns
Due to the nature of the 4 transistor design of the die used in these device types, topologically pure testing is important,
particularly for high reliability applications. The device manufacturer should be consulted concerning their testing methods
and algorithms.
Unless otherwise specified, the AC test conditions are as follows: Input pulse levels: VIL = 0 V and VIH = 3.0 V. Input rise
and fall times: 5 nanoseconds. Input and output timing reference levels: 1.5 V, + 0.5 V. Output loading: See paragraph
3.2.6 and figure 7. Unless otherwise specified the DC test conditions are as follows: VIL = 0.3 V, VIH = VCC -0.3 V.
Parameters shall be tested as part of device characterization and after design and process changes. Parameters shall
be to the limits specified in table I for all lots not specifically tested.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
14
Case outline M.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
2.03
2.54
.080
.100
A1
1.37
1.68
.054
.066
B
0.56
0.71
.022
.028
D
20.70
21.21
.815
.835
D1
18.80
19.30
.740
.760
E
11.18
11.68
.440
.460
e
1.27 BSC
.050 BSC
L
2.54 REF
.100 REF
L2
2.92
3.43
---
0.15
N
P
R
.115
.135
---
.006
32
0.23 REF
.009 REF
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin numbers are for reference only.
FIGURE 1. Case outline(s).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
15
Case outline N.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
2.03
2.54
.080
.100
A1
1.37
1.68
.054
.066
B
0.56
0.71
.022
.028
D
23.11
23.62
.910
.930
D1
21.34
21.84
.840
.860
E
11.30
11.68
.445
.460
e
1.27 BSC
L
.050 BSC
2.54 TYP
L2
2.92
.100 TYP
3.43
N
.115
.135
---
.006
36
P
---
R
0.15
0.23 TYP
.009 TYP
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
16
Case outline T.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
2.03
3.96
.080
.156
A1
1.02
1.60
.040
.063
b
0.38
0.51
.015
.020
C
0.15
0.30
.006
.012
D
20.70
21.34
.815
.840
D2
18.80
19.30
.740
.760
E
10.80
11.68
.425
.460
e
1.27 BSC
eA
9.30
R
10.41
.050 BSC
.366
0.89 TYP
.410
.035 TYP
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
17
Case outline U.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
2.26
3.18
.089
.125
b
0.38
0.48
.015
.019
C
0.08
0.18
.003
.007
D
23.11
23.62
.910
.930
D1
21.34
21.84
.840
.860
E
12.83
13.08
.505
.515
E1
9.78
10.03
.385
.395
E2
1.40
1.65
.055
.065
e
1.27 BSC
.050 BSC
L
7.62
8.89
.300
Q
0.38
0.96
.015
.350
.038
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. The case outline U is available in either a pedestal or non-pedestal package. The Q dimension only applies to the
pedestal version of case outline U.
3. For solder lead finish, dimensions b and C will increase by +.003 inches (+0.08 mm).
4. Pin number are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
18
Case outline X.
Symbol
A
b
B2
B3
B4
C
D
D1
D2
E
E1
E2
e
L
Q
Millimeters
Min
Max
2.31
3.18
0.38
0.48
32.64 TYP
3.81 TYP
37.72
38.48
0.08
0.18
23.11
23.62
21.46
21.72
4.83
5.33
12.83
13.08
9.78
10.03
1.40
1.65
1.27 BSC
12.19
13.21
0.38
0.64
Inches
Min
Max
.091
.125
.015
.019
1.285 TYP
.150 TYP
1.485
1.515
.003
.007
.910
.930
.845
.855
.190
.210
.505
.515
.385
.395
.055
.065
.050 BSC
.480
.520
.015
.025
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. The case outline X is available in either a pedestal or non-pedestal package. The Q dimension only applies to the
pedestal version of case outline X.
3. For solder lead finish, dimensions b and C will increase by +.003 inches (+0.08 mm).
4. Pin number are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
19
Case outline Y.
Symbol
A
A1
A2
B
B1
D
D1
D2
e
e1
Millimeters
Min
Max
2.26
5.13
0.48
1.52
3.18
0.20
0.30
14.99
15.49
40.23
42.82
14.73
15.37
37.90
38.30
2.41
2.67
0.41
0.51
Inches
Min
Max
.089
.202
.019
.060
.125
.008
.012
.590
.610
1.584
1.686
.580
.605
1.492
1.508
.095
.105
.016
.020
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. For solder lead finish, dimensions B and e1 will increase by +0.003" (+.008 mm).
Figure 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
20
Case outline Z.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
3.54
4.67
.136
.184
A1
1.02
1.60
.040
.063
b
0.38
0.51
.015
.020
C
0.15
0.30
.006
.012
D
23.11
23.62
.910
.930
D2
21.46
21.84
.845
.860
E
10.80
11.05
.425
.435
e
eA
R
1.27 BSC
9.30
9.80
0.050 BSC
.366
0.89 TYP
.386
.035 TYP
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
21
Case outline 9.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
2.44
2.90
.096
.114
b
0.20
0.48
.008
.019
c
0.08
0.20
.003
.008
D
20.73
21.29
.816
.838
D1
18.85
19.25
.742
.758
E
10.64
11.68
.419
.460
E2
8.76
10.85
.345
.427
e
1.27 BSC
L
7.37
.050 BSC
7.87
.290
.310
Q
0.61
0.97
.024
.038
NOTES:
1. The U.S. Government preferred system of measurement is the metric SI system. This item was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inchpound units shall rule.
2. Dimension E2 does not apply to optional configuration.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
22
Case outline 7.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
2.92
3.68
.115
.145
A1
.63
1.14
.025
.045
b
.38
.51
.015
.020
C
.15
.30
.006
.012
D
23.39
23.85
.921
.939
D2
21.46
21.71
.845
.855
E
10.54
10.92
.415
.430
e
1.27 BSC
eA
9.42
R
.050 BSC
9.83
.371
.76 TYP
.387
.030 TYP
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin numbers are for reference only.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
23
Device
types
05-13 and 19-30 for case outlines M and 9.
All for case outlines T and Y.
Case
outlines
M, T, Y, and 9
Case
outlines
M, T, Y, and 9
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
1
A18
17
I/O3
2
A16
18
I/O4
3
A14
19
I/O5
4
A12
20
I/O6
5
A7
21
I/O7
6
A6
22
CS
7
A5
23
A10
8
A4
24
OE
9
A3
25
A11
10
A2
26
A9
11
A1
27
A8
12
A0
28
A13
13
I/O0
29
WE
14
I/O1
30
A17
15
I/O2
31
A15
16
VSS
32
VCC
FIGURE 2. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
24
Device
types
05-13 and 19-30 for case outlines N, U, and Z
05-10 and 19-24 for case outline X.
05-13 and 19-29 for case outline 7.
Case
outlines
N, U, X, Z and 7
Case
outlines
N, U, X, Z and 7
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
1
A0
19
NC
2
A1
20
A10
3
A2
21
A11
4
A3
22
A12
5
A4
23
A13
6
CS
24
A14
7
I/O0
25
I/O4
8
I/O1
26
I/O5
9
VCC
27
VCC
10
VSS
28
VSS
11
I/O2
29
I/O6
12
I/O3
30
I/O7
13
WE
31
OE
14
A5
32
A15
15
A6
33
A16
16
A7
34
A17
17
A8
35
A18
18
A9
36
NC
FIGURE 2. Terminal connections - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
25
CS
OE
WE
Mode
Data I/O
Power
H
X
X
Standby
High Z
Standby
L
L
H
Read
Data out
Active
L
H
H
Output
disable
High Z
Active
L
X
L
Write
Data in
Active
NOTES:
1. H = VIH = High Logic Level.
2. L = VIL = Low Logic Level.
3. X = Do not care (either high or low).
4. High Z = High Impedance state.
FIGURE 3. Truth Table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
26
FIGURE 4. Read cycle timing diagram.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
27
FIGURE 5. Write cycle timing diagram.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
28
FIGURE 6. Block diagram.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
29
Parameter
Typical
Unit
Input pulse level
0 - 3.0
V
Input rise and fall
5
ns
Input and output reference level
1.5
V
Output load capacitance
50
pF
NOTES:
1. Use this output load circuit or equivalent for testing.
2. VZ is programmable from -2 V to +7 V.
3. IOL and IOH are programmable from 0 to 16 mA.
4. Tester impedance is ZO = 75 ohms.
5. VZ is typically the midpoint of VOH and VOL.
6. IOL and IOH are adjusted to simulate a typical resistive load circuit.
7. ATE tester includes jig capacitance.
FIGURE 7. Output load circuit.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
30
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group
A test table)
Interim electrical parameters
1,4,7,9
Final electrical parameters
1*,2,3,4,7,8A,8B,9,10,11
Group A test requirements
1,2,3,4,7,8A,8B,9,10,11
Group C end-point electrical
Parameters
1,2,3,4,7,8A,8B,9,10,11
End-point electrical parameters for
radiation hardness assurance
(RHA) devices
Not applicable
* PDA applies to subgroup 1.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. Tests shall be as specified in table II herein.
b. Subgroups 5 and 6 shall be omitted.
c. Subgroups 7 and 8 shall include verification of the truth table on figure 3.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test, method 1005 of MIL-STD-883.
(1)
Test condition B or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1005 of MIL-STD-883.
(2)
TA as specified in accordance with table I of method 1005 of MIL-STD-883.
(3)
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation hardness assurance (RHA) inspection. RHA inspection is currently not applicable to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
31
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list
will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices
(FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-0547.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have agreed to
this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-95613
A
REVISION LEVEL
K
SHEET
32
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 12-04-02
Approved sources of supply for SMD 5962-95613 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information
bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561301HYA
5962-9561301HYC
5962-9561301HTA
5962-9561301HTC
5962-9561301HYA
5962-9561301HYC
0EU86
0EU86
54230
54230
54230
54230
AS5C4009CW-120/H
AS5C4009CW-120/H
WMS512K8-120DE
WMS512K8-120DE
WMS512K8-120C
WMS512K8-120C
5962-9561302HYA
5962-9561302HYC
5962-9561302HTA
5962-9561302HTC
5962-9561302HYA
5962-9561302HYC
0EU86
0EU86
54230
54230
54230
54230
AS5C4009CW-100/H
AS5C4009CW-100/H
WMS512K8-100DE
WMS512K8-100DE
WMS512K8-100C
WMS512K8-100C
5962-9561303HYA
5962-9561303HYC
5962-9561303HTA
5962-9561303HTC
5962-9561303HYA
5962-9561303HYC
0EU86
0EU86
54230
54230
54230
54230
AS5C4009CW-85/H
AS5C4009CW-85/H
WMS512K8-85DE
WMS512K8-85DE
WMS512K8-85C
WMS512K8-85C
5962-9561304HYA
5962-9561304HYC
5962-9561304HTA
5962-9561304HTC
5962-9561304HYA
5962-9561304HYC
0EU86
0EU86
54230
54230
54230
54230
AS5C4009CW-70/H
AS5C4009CW-70/H
WMS512K8-70DE
WMS512K8-70DE
WMS512K8-70C
WMS512K8-70C
See footnotes at end of table.
1 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561305HMA
5962-9561305HMC
5962-9561305HNA
5962-9561305HNC
5962-9561305HTA
5962-9561305HTC
5962-9561305HTA
5962-9561305HTC
5962-9561305HUA
5962-9561305HUC
5962-9561305HUA
5962-9561305HUC
5962-9561305HUA
5962-9561305HUC
5962-9561305HXC
5962-9561305HYA
5962-9561305HYC
5962-9561305HYA
5962-9561305HYC
5962-9561305HYA
5962-9561305HYC
5962-9561305HZA
5962-9561305HZC
5962-9561305HZA
5962-9561305HZC
5962-9561305HZA
5962-9561305HZC
5962-9561305H9A
5962-9561305H9C
5962-9561305H7A
5962-9561305H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
4/
4/
54230
54230
54230
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-55/H
AS5C4008EC-55/H
AS5C512K8EC-55/H
AS5C512K8EC-55/H
AS5C4008ECJ-55/H
AS5C4008ECJ-55/H
WMS512K8-55DE
WMS512K8-55DE
AS5C512K8F-55/H
AS5C512K8F-55/H
ACT-S512K8N-055F3Q
ACT-S512K8N-055F3Q
WMS512K8-55FT
WMS512K8-55FT
WMS512K8-55F
AS5C4008CW-55/H
AS5C4008CW-55/H
WMS512K8-55C
WMS512K8-55C
ACT-S512K8N-055P4Q
ACT-S512K8N-055P4Q
AS5C512K8ECJ-55/H
AS5C512K8ECJ-55/H
WMS512K8-55DJ
WMS512K8-55DJ
ACT-S512K8N-055F4Q
ACT-S512K8N-055F4Q
AS5C4008F-55/H
AS5C4008F-55/H
AS5C512K8 SOJ -55/H
AS5C512K8 SOJ -55/H
See footnotes at end of table.
2 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561306HMA
5962-9561306HMC
5962-9561306HNA
5962-9561306HNC
5962-9561306HTA
5962-9561306HTC
5962-9561306HTA
5962-9561306HTC
5962-9561306HUA
5962-9561306HUC
5962-9561306HUA
5962-9561306HUC
5962-9561306HUA
5962-9561306HUC
5962-9561306HXC
5962-9561306HYA
5962-9561306HYC
5962-9561306HYA
5962-9561306HYC
5962-9561306HYA
5962-9561306HYC
5962-9561306HZA
5962-9561306HZC
5962-9561306HZA
5962-9561306HZC
5962-9561306HZA
5962-9561306HZC
5962-9561306H9A
5962-9561306H9C
5962-9561306H7A
5962-9561306H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
4/
4/
54230
54230
54230
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-45/H
AS5C4008EC-45/H
AS5C512K8EC-45/H
AS5C512K8EC-45/H
AS5C4008ECJ-45/H
AS5C4008ECJ-45/H
WMS512K8-45DE
WMS512K8-45DE
AS5C512K8F-45/H
AS5C512K8F-45/H
ACT-S512K8N-045F3Q
ACT-S512K8N-045F3Q
WMS512K8-45FT
WMS512K8-45FT
WMS512K8-45F
AS5C4008CW-45/H
AS5C4008CW-45/H
WMS512K8-45C
WMS512K8-45C
ACT-S512K8N-045P4Q
ACT-S512K8N-045P4Q
AS5C512K8ECJ-45/H
AS5C512K8ECJ-45/H
WMS512K8-45DJ
WMS512K8-45DJ
ACT-S512K8N-045F4Q
ACT-S512K8N-045F4Q
AS5C4008F-45/H
AS5C4008F-45/H
AS5C512K8SOJ -45/H
AS5C512K8SOJ -45/H
See footnotes at end of table.
3 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561307HMA
5962-9561307HMC
5962-9561307HNA
5962-9561307HNC
5962-9561307HTA
5962-9561307HTC
5962-9561307HTA
5962-9561307HTC
5962-9561307HUA
5962-9561307HUC
5962-9561307HUA
5962-9561307HUC
5962-9561307HUA
5962-9561307HUC
5962-9561307HXC
5962-9561307HYA
5962-9561307HYC
5962-9561307HYA
5962-9561307HYC
5962-9561307HYA
5962-9561307HYC
5962-9561307HZA
5962-9561307HZC
5962-9561307HZA
5962-9561307HZC
5962-9561307HZA
5962-9561307HZC
5962-9561307H9A
5962-9561307H9C
5962-9561307H7A
5962-9561307H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
4/
4/
54230
54230
54230
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-35/H
AS5C4008EC-35/H
AS5C512K8EC-35/H
AS5C512K8EC-35/H
AS5C4008ECJ-35/H
AS5C4008ECJ-35/H
WMS512K8-35DE
WMS512K8-35DE
AS5C512K8F-35/H
AS5C512K8F-35/H
ACT-S512K8N-035F3Q
ACT-S512K8N-035F3Q
WMS512K8-35FT
WMS512K8-35FT
WMS512K8-35F
AS5C4008CW-35/H
AS5C4008CW-35/H
WMS512K8-35C
WMS512K8-35C
ACT-S512K8N-035P4Q
ACT-S512K8N-035P4Q
AS5C512K8ECJ-35/H
AS5C512K8ECJ-35/H
WMS512K8-35DJ
WMS512K8-35DJ
ACT-S512K8N-035F4Q
ACT-S512K8N-035F4Q
AS5C4008F-35/H
AS5C4008F-35/H
AS5C512K8SOJ-35/H
AS5C512K8SOJ-35/H
See footnotes at end of table.
4 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561308HMA
5962-9561308HMC
5962-9561308HNA
5962-9561308HNC
5962-9561308HTA
5962-9561308HTC
5962-9561308HTA
5962-9561308HTC
5962-9561308HUA
5962-9561308HUC
5962-9561308HUA
5962-9561308HUC
5962-9561308HUA
5962-9561308HUC
5962-9561308HXC
5962-9561308HYA
5962-9561308HYC
5962-9561308HYA
5962-9561308HYC
5962-9561308HYA
5962-9561308HYC
5962-9561308HZA
5962-9561308HZC
5962-9561308HZA
5962-9561308HZC
5962-9561308HZA
5962-9561308HZC
5962-9561308H9A
5962-9561308H9C
5962-9561308H7A
5962-9561308H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
4/
4/
54230
54230
54230
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-25/H
AS5C4008EC-25/H
AS5C512K8EC-25/H
AS5C512K8EC-25/H
AS5C4008ECJ-25/H
AS5C4008ECJ-25/H
WMS512K8-25DE
WMS512K8-25DE
AS5C512K8F-25/H
AS5C512K8F-25/H
ACT-S512K8N-025F3Q
ACT-S512K8N-025F3Q
WMS512K8-25FT
WMS512K8-25FT
WMS512K8-25F
AS5C4008CW-25/H
AS5C4008CW-25/H
WMS512K8-25C
WMS512K8-25C
ACT-S512K8N-025P4Q
ACT-S512K8N-025P4Q
AS5C512K8ECJ-25/H
AS5C512K8ECJ-25/H
WMS512K8-25DJ
WMS512K8-25DJ
ACT-S512K8N-025F4Q
ACT-S512K8N-025F4Q
AS5C4008F-25/H
AS5C4008F-25/H
AS5C512K8SOJ-25/H
AS5C512K8SOJ-25/H
See footnotes at end of table.
5 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561309HMA
5962-9561309HMC
5962-9561309HNA
5962-9561309HNC
5962-9561309HTA
5962-9561309HTC
5962-9561309HTA
5962-9561309HTC
5962-9561309HUA
5962-9561309HUC
5962-9561309HUA
5962-9561309HUC
5962-9561309HUA
5962-9561309HUC
5962-9561309HXC
5962-9561309HYA
5962-9561309HYC
5962-9561309HYA
5962-9561309HYC
5962-9561309HYA
5962-9561309HYC
5962-9561309HZA
5962-9561309HZC
5962-9561309HZA
5962-9561309HZC
5962-9561309HZA
5962-9561309HZC
5962-9561309H9A
5962-9561309H9C
5962-9561309H7A
5962-9561309H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
4/
4/
54230
54230
54230
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-20/H
AS5C4008EC-20/H
AS5C512K8EC-20/H
AS5C512K8EC-20/H
AS5C4008ECJ-20/H
AS5C4008ECJ-20/H
WMS512K8-20DE
WMS512K8-20DE
AS5C512K8F-20/H
AS5C512K8F-20/H
ACT-S512K8N-020F3Q
ACT-S512K8N-020F3Q
WMS512K8-20FT
WMS512K8-20FT
WMS512K8-20F
AS5C4008CW-20/H
AS5C4008CW-20/H
WMS512K8-20C
WMS512K8-20C
ACT-S512K8N-020P4Q
ACT-S512K8N-020P4Q
AS5C512K8ECJ-20/H
AS5C512K8ECJ-20/H
WMS512K8-20DJ
WMS512K8-20DJ
ACT-S512K8N-020F4Q
ACT-S512K8N-020F4Q
AS5C4008F-20/H
AS5C4008F-20/H
AS5C512K8SOJ-20/H
AS5C512K8SOJ-20/H
See footnotes at end of table.
6 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561310HMA
5962-9561310HMC
5962-9561310HNA
5962-9561310HNC
5962-9561310HTA
5962-9561310HTC
5962-9561310HTA
5962-9561310HTC
5962-9561310HUA
5962-9561310HUC
5962-9561310HUA
5962-9561310HUC
5962-9561310HUA
5962-9561310HUC
5962-9561310HXC
5962-9561310HYA
5962-9561310HYC
5962-9561310HYA
5962-9561310HYC
5962-9561310HYA
5962-9561310HYC
5962-9561310HZA
5962-9561310HZC
5962-9561310HZA
5962-9561310HZC
5962-9561310HZA
5962-9561310HZC
5962-9561310H9A
5962-9561310H9C
5962-9561310H7A
5962-9561310H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
4/
4/
54230
54230
54230
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-17/H
AS5C4008EC-17/H
AS5C512K8EC-17/H
AS5C512K8EC-17/H
AS5C4008ECJ-17/H
AS5C4008ECJ-17/H
WMS512K8-17DE
WMS512K8-17DE
AS5C512K8F-17/H
AS5C512K8F-17/H
ACT-S512K8N-017F3Q
ACT-S512K8N-017F3Q
WMS512K8-17FT
WMS512K8-17FT
WMS512K8-17F
AS5C4008CW-17/H
AS5C4008CW-17/H
WMS512K8-17C
WMS512K8-17C
ACT-S512K8N-017P4Q
ACT-S512K8N-017P4Q
AS5C512K8ECJ-17/H
AS5C512K8ECJ-17/H
WMS512K8-17DJ
WMS512K8-17DJ
ACT-S512K8N-017F4Q
ACT-S512K8N-017F4Q
AS5C4008F-17/H
AS5C4008F-17/H
AS5C512K8SOJ-17/H
AS5C512K8SOJ-17/H
See footnotes at end of table.
7 of 15
TANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561311HMA
5962-9561311HMC
5962-9561311HNA
5962-9561311HNC
5962-9561311HTA
5962-9561311HTC
5962-9561311HTA
5962-9561311HTC
5962-9561311HUA
5962-9561311HUC
5962-9561311HYA
5962-9561311HYC
5962-9561311HYA
5962-9561311HYC
5962-9561311HYA
5962-9561311HYC
5962-9561311HZA
5962-9561311HZC
5962-9561311H9A
5962-9561311H9C
5962-9561311H7A
5962-9561311H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-45/H
AS5C4008EC-45/H
AS5C512K8EC-45/H
AS5C512K8EC-45/H
AS5C4008ECJ-45/H
AS5C4008ECJ-45/H
WMS512K8M-45DE
WMS512K8M-45DE
AS5C512K8F-45/H
AS5C512K8F-45/H
AS5C4008CW-45/H
AS5C4008CW-45/H
WMS512K8M-45C
WMS512K8M-45C
ACT-S512K8M-045P4Q
ACT-S512K8M-045P4Q
AS5C512K8ECJ-45/H
AS5C512K8ECJ-45/H
AS5C4008F-45/H
AS5C4008F-45/H
AS5C512K8SOJ-45/H
AS5C512K8SOJ-45/H
5962-9561312HMA
5962-9561312HMC
5962-9561312HNA
5962-9561312HNC
5962-9561312HTA
5962-9561312HTC
5962-9561312HTA
5962-9561312HTC
5962-9561312HUA
5962-9561312HUC
5962-9561312HYA
5962-9561312HYC
5962-9561312HYA
5962-9561312HYC
5962-9561312HYA
5962-9561312HYC
5962-9561312HZA
5962-9561312HZC
5962-9561312H9A
5962-9561312H9C
5962-9561312H7A
5962-9561312H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-35/H
AS5C4008EC-35/H
AS5C512K8EC-35/H
AS5C512K8EC-35/H
AS5C4008ECJ-35/H
AS5C4008ECJ-35/H
WMS512K8M-35DE
WMS512K8M-35DE
AS5C512K8F-35/H
AS5C512K8F-35/H
AS5C4008CW-35/H
AS5C4008CW-35/H
WMS512K8M-35C
WMS512K8M-35C
ACT-S512K8M-035P4Q
ACT-S512K8M-035P4Q
AS5C512K8ECJ-35/H
AS5C512K8ECJ-35/H
AS5C4008F-35/H
AS5C4008F-35/H
AS5C512K8SOJ-35/H
AS5C512K8SOJ-35/H
See footnotes at end of table.
8 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561313HMA
5962-9561313HMC
5962-9561313HNA
5962-9561313HNC
5962-9561313HTA
5962-9561313HTC
5962-9561313HTA
5962-9561313HTC
5962-9561313HUA
5962-9561313HUC
5962-9561313HYA
5962-9561313HYC
5962-9561313HYA
5962-9561313HYC
5962-9561313HYA
5962-9561313HYC
5962-9561313HZA
5962-9561313HZC
5962-9561313H9A
5962-9561313H9C
5962-9561313H7A
5962-9561313H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
54230
54230
4/
4/
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-25/H
AS5C4008EC-25/H
AS5C512K8EC-25/H
AS5C512K8EC-25/H
AS5C4008ECJ-25/H
AS5C4008ECJ-25/H
WMS512K8M-25DE
WMS512K8M-25DE
AS5C512K8F-25/H
AS5C512K8F-25/H
AS5C4008CW-25/H
AS5C4008CW-25/H
WMS512K8M-25C
WMS512K8M-25C
ACT-S512K8M-025P4Q
ACT-S512K8M-025P4Q
AS5C512K8ECJ-25/H
AS5C512K8ECJ-25/H
AS5C4008F-25/H
AS5C4008F-25/H
AS5C512K8SOJ-25/H
AS5C512K8SOJ-25/H
5962-9561314HTA
5962-9561314HTC
5962-9561314HYA
5962-9561314HYC
54230
54230
54230
54230
WMS512K8-15DE
WMS512K8-15DE
WMS512K8-15C
WMS512K8-15C
5962-9561315HYA
5962-9561315HYC
5962-9561315HTA
5962-9561315HTC
5962-9561315HYA
5962-9561315HYC
0EU86
0EU86
54230
54230
54230
54230
AS5C4009CW-120L/H
AS5C4009CW-120L/H
WMS512K8L-120DE
WMS512K8L-120DE
WMS512K8L-120C
WMS512K8L-120C
5962-9561316HYA
5962-9561316HYC
5962-9561316HTA
5962-9561316HTC
5962-9561316HYA
5962-9561316HYC
0EU86
0EU86
54230
54230
54230
54230
AS5C4009CW-100L/H
AS5C4009CW-100L/H
WMS512K8L-100DE
WMS512K8L-100DE
WMS512K8L-100C
WMS512K8L-100C
5962-9561317HYA
5962-9561317HYC
5962-9561317HTA
5962-9561317HTC
5962-9561317HYA
5962-9561317HYC
0EU86
0EU86
54230
54230
54230
54230
AS5C4009CW-85L/H
AS5C4009CW-85L/H
WMS512K8L-85DE
WMS512K8L-85DE
WMS512K8L-85C
WMS512K8L-85C
5962-9561318HYA
5962-9561318HYC
5962-9561318HTA
5962-9561318HTC
5962-9561318HYA
5962-9561318HYC
0EU86
0EU86
54230
54230
54230
54230
AS5C4009CW-70L/H
AS5C4009CW-70L/H
WMS512K8L-70DE
WMS512K8L-70DE
WMS512K8L-70C
WMS512K8L-70C
See footnotes at end of table.
9 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561319HMA
5962-9561319HMC
5962-9561319HNA
5962-9561319HNC
5962-9561319HTA
5962-9561319HTC
5962-9561319HTA
5962-9561319HTC
5962-9561319HUA
5962-9561319HUC
5962-9561319HUA
5962-9561319HUC
5962-9561319HXC
5962-9561319HYA
5962-9561319HYC
5962-9561319HYA
5962-9561319HYC
5962-9561319HZA
5962-9561319HZC
5962-9561319HZA
5962-9561319HZC
5962-9561319H9A
5962-9561319H9C
5962-9561319H7A
5962-9561319H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-55L/H
AS5C4008EC-55L/H
AS5C512K8EC-55L/H
AS5C512K8EC-55L/H
AS5C4008ECJ-55L/H
AS5C4008ECJ-55L/H
WMS512K8L-55DE
WMS512K8L-55DE
AS5C512K8F-55L/H
AS5C512K8F-55L/H
WMS512K8L-55FT
WMS512K8L-55FT
WMS512K8L-55F
AS5C4008CW-55L/H
AS5C4008CW-55L/H
WMS512K8L-55C
WMS512K8L-55C
AS5C512K8ECJ-55L/H
AS5C512K8ECJ-55L/H
WMS512K8L-55DJ
WMS512K8L-55DJ
AS5C4008F-55L/H
AS5C4008F-55L/H
AS5C512K8SOJ-55L/H
AS5C512K8SOJ-55L/H
5962-9561320HMA
5962-9561320HMC
5962-9561320HNA
5962-9561320HNC
5962-9561320HTA
5962-9561320HTC
5962-9561320HTA
5962-9561320HTC
5962-9561320HUA
5962-9561320HUC
5962-9561320HUA
5962-9561320HUC
5962-9561320HXC
5962-9561320HYA
5962-9561320HYC
5962-9561320HYA
5962-9561320HYC
5962-9561320HZA
5962-9561320HZC
5962-9561320HZA
5962-9561320HZC
5962-9561320H9A
5962-9561320H9C
5962-9561320H7A
5962-9561320H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-45L/H
AS5C4008EC-45L/H
AS5C512K8EC-45L/H
AS5C512K8EC-45L/H
AS5C4008ECJ-45L/H
AS5C4008ECJ-45L/H
WMS512K8L-45DE
WMS512K8L-45DE
AS5C512K8F-45L/H
AS5C512K8F-45L/H
WMS512K8L-45FT
WMS512K8L-45FT
WMS512K8L-45F
AS5C4008CW-45L/H
AS5C4008CW-45L/H
WMS512K8L-45C
WMS512K8L-45C
AS5C512K8ECJ-45L/H
AS5C512K8ECJ-45L/H
WMS512K8L-45DJ
WMS512K8L-45DJ
AS5C4008F-45L/H
AS5C4008F-45L/H
AS5C512K8SOJ-45L/H
AS5C512K8SOJ-45L/H
See footnotes at end of table.
10 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561321HMA
5962-9561321HMC
5962-9561321HNA
5962-9561321HNC
5962-9561321HTA
5962-9561321HTC
5962-9561321HTA
5962-9561321HTC
5962-9561321HUA
5962-9561321HUC
5962-9561321HUA
5962-9561321HUC
5962-9561321HXC
5962-9561321HYA
5962-9561321HYC
5962-9561321HYA
5962-9561321HYC
5962-9561321HZA
5962-9561321HZC
5962-9561321HZA
5962-9561321HZC
5962-9561321H9A
5962-9561321H9C
5962-9561321H7A
5962-9561321H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-35L/H
AS5C4008EC-35L/H
AS5C512K8EC-35L/H
AS5C512K8EC-35L/H
AS5C4008ECJ-35L/H
AS5C4008ECJ-35L/H
WMS512K8L-35DE
WMS512K8L-35DE
AS5C512K8F-35L/H
AS5C512K8F-35L/H
WMS512K8L-35FT
WMS512K8L-35FT
WMS512K8L-35F
AS5C4008CW-35L/H
AS5C4008CW-35L/H
WMS512K8L-35C
WMS512K8L-35C
AS5C512K8ECJ-35L/H
AS5C512K8ECJ-35L/H
WMS512K8L-35DJ
WMS512K8L-35DJ
AS5C4008F-35L/H
AS5C4008F-35L/H
AS5C512K8SOJ-35L/H
AS5C512K8SOJ-35L/H
5962-9561322HMA
5962-9561322HMC
5962-9561322HNA
5962-9561322HNC
5962-9561322HTA
5962-9561322HTC
5962-9561322HTA
5962-9561322HTC
5962-9561322HUA
5962-9561322HUC
5962-9561322HUA
5962-9561322HUC
5962-9561322HXC
5962-9561322HYA
5962-9561322HYC
5962-9561322HYA
5962-9561322HYC
5962-9561322HZA
5962-9561322HZC
5962-9561322HZA
5962-9561322HZC
5962-9561322H9A
5962-9561322H9C
5962-9561322H7A
5962-9561322H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-25L/H
AS5C4008EC-25L/H
AS5C512K8EC-25L/H
AS5C512K8EC-25L/H
AS5C4008ECJ-25L/H
AS5C4008ECJ-25L/H
WMS512K8L-25DE
WMS512K8L-25DE
AS5C512K8F-25L/H
AS5C512K8F-25L/H
WMS512K8L-25FT
WMS512K8L-25FT
WMS512K8L-25F
AS5C4008CW-25L/H
AS5C4008CW-25L/H
WMS512K8L-25C
WMS512K8L-25C
AS5C512K8ECJ-25L/H
AS5C512K8ECJ-25L/H
WMS512K8L-25DJ
WMS512K8L-25DJ
AS5C4008F-25L/H
AS5C4008F-25L/H
AS5C512K8SOJ-25L/H
AS5C512K8SOJ-25L/H
See footnotes at end of table.
11 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561323HMA
5962-9561323HMC
5962-9561323HNA
5962-9561323HNC
5962-9561323HTA
5962-9561323HTC
5962-9561323HTA
5962-9561323HTC
5962-9561323HUA
5962-9561323HUC
5962-9561323HUA
5962-9561323HUC
5962-9561323HXC
5962-9561323HYA
5962-9561323HYC
5962-9561323HYA
5962-9561323HYC
5962-9561323HZA
5962-9561323HZC
5962-9561323HZA
5962-9561323HZC
5962-9561323H9A
5962-9561323H9C
5962-9561323H7A
5962-9561323H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-20L/H
AS5C4008EC-20L/H
AS5C512K8EC-20L/H
AS5C512K8EC-20L/H
AS5C4008ECJ-20L/H
AS5C4008ECJ-20L/H
WMS512K8L-20DE
WMS512K8L-20DE
AS5C512K8F-20L/H
AS5C512K8F-20L/H
WMS512K8L-20FT
WMS512K8L-20FT
WMS512K8L-20F
AS5C4008CW-20L/H
AS5C4008CW-20L/H
WMS512K8L-20C
WMS512K8L-20C
AS5C512K8ECJ-20L/H
AS5C512K8ECJ-20L/H
WMS512K8L-20DJ
WMS512K8L-20DJ
AS5C4008F-20L/H
AS5C4008F-20L/H
AS5C512K8SOJ-20L/H
AS5C512K8SOJ-20L/H
5962-9561324HMA
5962-9561324HMC
5962-9561324HNA
5962-9561324HNC
5962-9561324HTA
5962-9561324HTC
5962-9561324HTA
5962-9561324HTC
5962-9561324HUA
5962-9561324HUC
5962-9561324HUA
5962-9561324HUC
5962-9561324HXC
5962-9561324HYA
5962-9561324HYC
5962-9561324HYA
5962-9561324HYC
5962-9561324HZA
5962-9561324HZC
5962-9561324HZA
5962-9561324HZC
5962-9561324H9A
5962-9561324H9C
5962-9561324H7A
5962-9561324H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-17L/H
AS5C4008EC-17L/H
AS5C512K8EC-17L/H
AS5C512K8EC-17L/H
AS5C4008ECJ-17L/H
AS5C4008ECJ-17L/H
WMS512K8L-17DE
WMS512K8L-17DE
AS5C512K8F-17L/H
AS5C512K8F-17L/H
WMS512K8L-17FT
WMS512K8L-17FT
WMS512K8L-17F
AS5C4008CW-17L/H
AS5C4008CW-17L/H
WMS512K8L-17C
WMS512K8L-17C
AS5C512K8ECJ-17L/H
AS5C512K8ECJ-17L/H
WMS512K8L-17DJ
WMS512K8L-17DJ
AS5C4008F-17L/H
AS5C4008F-17L/H
AS5C512K8SOJ-17L/H
AS5C512K8SOJ-17L/H
See footnotes at end of table.
12 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561325HMA
5962-9561325HMC
5962-9561325HNA
5962-9561325HNC
5962-9561325HTA
5962-9561325HTC
5962-9561325HUA
5962-9561325HUC
5962-9561325HYA
5962-9561325HYC
5962-9561325HZA
5962-9561325HZC
5962-9561325H9A
5962-9561325H9C
5962-9561325H7A
5962-9561325H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-45L/H
AS5C4008EC-45L/H
AS5C512K8EC-45L/H
AS5C512K8EC-45L/H
AS5C4008ECJ-45L/H
AS5C4008ECJ-45L/H
AS5C512K8F-45L/H
AS5C512K8F-45L/H
AS5C4008CW-45L/H
AS5C4008CW-45L/H
AS5C512K8ECJ-45L/H
AS5C512K8ECJ-45L/H
AS5C4008F-45L/H
AS5C4008F-45L/H
AS5C512K8SOJ-45L/H
AS5C512K8SOJ-45L/H
5962-9561326HMA
5962-9561326HMC
5962-9561326HNA
5962-9561326HNC
5962-9561326HTA
5962-9561326HTC
5962-9561326HUA
5962-9561326HUC
5962-9561326HYA
5962-9561326HYC
5962-9561326HZA
5962-9561326HZC
5962-9561326H9A
5962-9561326H9C
5962-9561326H7A
5962-9561326H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-35L/H
AS5C4008EC-35L/H
AS5C512K8EC-35L/H
AS5C512K8EC-35L/H
AS5C4008ECJ-35L/H
AS5C4008ECJ-35L/H
AS5C512K8F-35L/H
AS5C512K8F-35L/H
AS5C4008CW-35L/H
AS5C4008CW-35L/H
AS5C512K8ECJ-35L/H
AS5C512K8ECJ-35L/H
AS5C4008F-35L/H
AS5C4008F-35L/H
AS5C512K8SOJ-35L/H
AS5C512K8SOJ-35L/H
5962-9561327HMA
5962-9561327HMC
5962-9561327HNA
5962-9561327HNC
5962-9561327HTA
5962-9561327HTC
5962-9561327HUA
5962-9561327HUC
5962-9561327HYA
5962-9561327HYC
5962-9561327HZA
5962-9561327HZC
5962-9561327H9A
5962-9561327H9C
5962-9561327H7A
5962-9561327H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-25L/H
AS5C4008EC-25L/H
AS5C512K8EC-25L/H
AS5C512K8EC-25L/H
AS5C4008ECJ-25L/H
AS5C4008ECJ-25L/H
AS5C512K8F-25L/H
AS5C512K8F-25L/H
AS5C4008CW-25L/H
AS5C4008CW-25L/H
AS5C512K8ECJ-25L/H
AS5C512K8ECJ-25L/H
AS5C4008F-25L/H
AS5C4008F-25L/H
AS5C512K8SOJ-25L/H
AS5C512K8SOJ-25L/H
See footnotes at end of table.
13 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561328HMA
5962-9561328HMC
5962-9561328HNA
5962-9561328HNC
5962-9561328HTA
5962-9561328HTC
5962-9561328HTA
5962-9561328HTC
5962-9561328HUA
5962-9561328HUC
5962-9561328HUA
5962-9561328HUC
5962-9561328HXC
5962-9561328HYA
5962-9561328HYC
5962-9561328HYA
5962-9561328HYC
5962-9561328HZA
5962-9561328HZC
5962-9561328HZA
5962-9561328HZC
5962-9561328H9A
5962-9561328H9C
5962-9561328H7A
5962-9561328H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-12L/H
AS5C4008EC-12L/H
AS5C512K8EC-12L/H
AS5C512K8EC-12L/H
AS5C4008ECJ-12L/H
AS5C4008ECJ-12L/H
WMS512K8L-12DE
WMS512K8L-12DE
AS5C512K8F-12L/H
AS5C512K8F-12L/H
WMS512K8L-12FT
WMS512K8L-12FT
WMS512K8L-12F
AS5C4008CW-12L/H
AS5C4008CW-12L/H
WMS512K8L-12C
WMS512K8L-12C
AS5C512K8ECJ-12L/H
AS5C512K8ECJ-12L/H
WMS512K8L-12DJ
WMS512K8L-12DJ
AS5C4008F-12L/H
AS5C4008F-12L/H
AS5C512K8SOJ-12L/H
AS5C512K8SOJ-12L/H
5962-9561329HMA
5962-9561329HMC
5962-9561329HNA
5962-9561329HNC
5962-9561329HTA
5962-9561329HTC
5962-9561329HTA
5962-9561329HTC
5962-9561329HUA
5962-9561329HUC
5962-9561329HUA
5962-9561329HUC
5962-9561329HXC
5962-9561329HYA
5962-9561329HYC
5962-9561329HYA
5962-9561329HYC
5962-9561329HZA
5962-9561329HZC
5962-9561329HZA
5962-9561329HZC
5962-9561329H9A
5962-9561329H9C
5962-9561329H7A
5962-9561329H7C
0EU86
0EU86
0EU86
0EU86
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
54230
54230
0EU86
0EU86
0EU86
0EU86
AS5C4008EC-12/H
AS5C4008EC-12/H
AS5C512K8EC-12/H
AS5C512K8EC-12/H
AS5C4008ECJ-12/H
AS5C4008ECJ-12/H
WMS512K8-12DE
WMS512K8-12DE
AS5C512K8F-12/H
AS5C512K8F-12/H
WMS512K8-12FT
WMS512K8-12FT
WMS512K8-12F
AS5C4008CW-12/H
AS5C4008CW-12/H
WMS512K8-12C
WMS512K8-12C
AS5C512K8ECJ-12/H
AS5C512K8ECJ-12/H
WMS512K8-12DJ
WMS512K8-12DJ
AS5C4008F-12/H
AS5C4008F-12/H
AS5C512K8SOJ-12/H
AS5C512K8SOJ-12/H
Se footnotes at end of table.
14 of 15
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 12-04-02
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9561330HTA
5962-9561330HTC
5962-9561330HUA
5962-9561330HUC
5962-9561330HXC
5962-9561330HYA
5962-9561330HYC
5962-9561330HZA
5962-9561330HZC
54230
54230
54230
54230
54230
54230
54230
54230
54230
WMS512K8U-12DE
WMS512K8U-12DE
WMS512K8U-12FT
WMS512K8U-12FT
WMS512K8U-12F
WMS512K8U-12C
WMS512K8U-12C
WMS512K8U-12DJ
WMS512K8U-12DJ
1/ The lead finish for each PIN representing a hermetic package is the most readily available from the manufacturer
listed for that part. If the desired lead finish is not listed contact the manufacturer to determine its availability.
2/ Device types and case outlines may be similar to the device types and case outlines listed on SMD 5962-95600.
3/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the
performance requirements of this drawing.
4/ No longer available from an approved source of supply.
Vendor CAGE
number
Vendor name
and address
0EU86
Austin Semiconductor, Incorporated
DBA Micross Components
8701 Cross Park Drive
Austin, TX 78754
54230
White Electronic Designs Corporation
3601 East University Drive
Phoenix, AZ 85034
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
15 of 15