PHILIPS 74F112

INTEGRATED CIRCUITS
74F112
Dual J-K negative edge-triggered flip-flop
Product specification
IC15 Data Handbook
1990 Feb 09
Philips Semiconductors
Product specification
Dual J-K negative edge-triggered flip-flop
FEATURE
74F112
PIN CONFIGURATION
• Industrial temperature range available (–40°C to +85°C)
CP0
1
16
VCC
DESCRIPTION
K0
2
15
RD0
The 74F112, Dual Negative Edge-Triggered JK-Type Flip-Flop,
feature individual J, K, Clock (CPn), Set (SD) and Reset (RD)
inputs, true (Qn) and complementary (Qn) outputs.
J0
3
14
RD1
SD0
4
13
CP1
Q0
5
12
K1
Q0
6
11
J1
Q1
7
10
SD1
GND
8
9
Q1
The SD and RD inputs, when Low, set or reset the outputs as shown
in the Function Table, regardless of the level at the other inputs.
A High level on the clock (CPn) input enables the J and K inputs and
data will be accepted. The logic levels at the J and K inputs may be
allowed to change while the CPn is High and flip-flop will perform
according to the Function Table as long as minimum setup and hold
times are observed. Output changes are initiated by the High-to-Low
transition of the CPn.
SF00103
TYPE
TYPICAL PROPAGATION DELAY
TYPICAL SUPPLY CURRENT (TOTAL)
74F112
100MHz
15mA
ORDERING INFORMATION
ORDER CODE
DESCRIPTION
COMMERCIAL RANGE
VCC = 5V ±10%, Tamb = 0°C to +70°C
INDUSTRIAL RANGE
VCC = 5V ±10%, Tamb = –40°C to +85°C
PKG DWG #
16-pin plastic DIP
N74F112N
I74F112N
SOT38-4
16-pin plastic SO
N74F112D
I74F112D
SOT109-1
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
74F (U.L.) HIGH/LOW
LOAD VALUE HIGH/LOW
J0, J1
PINS
J inputs
DESCRIPTION
1.0/1.0
20µA/0.6mA
K0, K1
K inputs
1.0/1.0
20µA/0.6mA
SD0, SD1
Set inputs (active Low)
1.0/5.0
20µA/3.0mA
RD0, RD1
Reset inputs (active Low)
1.0/5.0
20µA/3.0mA
CP0, CP1
Clock Pulse input (active falling edge)
1.0/4.0
20µA/2.4mA
Data outputs
50/33
1.0mA/20mA
Q0, Q0; Q1, Q1
NOTE:
One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.
February 9, 1990
2
853–0338 98775
Philips Semiconductors
Product specification
Dual J-K negative edge-triggered flip-flop
LOGIC SYMBOL
74F112
IEC/IEEE SYMBOL
3
11
2 12
3
1
1
J0
CP0
4
SD0
15
RD0
13
CP1
10
SD1
2
K0 K1
J1
15
4
11
14
13
RD1
12
Q0 Q0 Q1 Q1
14
10
5
VCC = Pin 16
GND = Pin 8
6
9
5
1J
C1
6
1K
R
S
2J
9
C2
2K
7
R
S
7
SF00105
SF00104
LOGIC DIAGRAM
5, 9
6, 7
Qn
Qn
4, 10
15, 14
SDn
RDn
2, 12
3, 11
Kn
Jn
1, 13
VCC = Pin 16
GND = Pin 8
CPn
SF00106
FUNCTION TABLE
INPUTS
OUTPUTS
SD
RD
CP
J
K
Q
OPERATING MODE
Q
L
H
X
X
X
H
L
Asynchronous Set
H
L
X
X
X
L
H
Asynchronous Reset
L
L
X
X
X
H*
H*
Undetermined *
H
H
↓
h
h
q
q
Toggle
H
H
↓
l
h
L
H
Load “0” (Reset)
H
H
↓
h
l
H
L
Load “1” (Set)
H
H
↓
l
l
q
q
Hold “no change”
H
H
H
X
X
Q
Q
Hold “no change”
H = High voltage level
h = High voltage level one setup time prior to High-to-Low clock transition
L = Low voltage level
l = Low voltage level one setup time prior to High-to-Low clock transition
q = Lower case letters indicate the state of the reference output prior to the High-to-Low clock transition
X = Don’t care
↓ = High-to-Low clock transition
* = Both outputs will be High while both SD and RD are Low, but the output states are unpredictable if SD and RD go High simultaneously.
February 9, 1990
3
Philips Semiconductors
Product specification
Dual J-K negative edge-triggered flip-flop
74F112
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limits set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.)
SYMBOL
PARAMETER
RATING
UNIT
VCC
Supply voltage
–0.5 to +7.0
V
VIN
Input voltage
–0.5 to +7.0
V
IIN
Input current
VOUT
Voltage applied to output in High output state
IOUT
Current applied to output in Low output state
Tamb
free air temperature range
Operating free-air
Tstg
Storage temperature range
–30 to +5
mA
–0.5 to VCC
V
40
mA
Commercial range
0 to +70
°C
Industrial range
–40 to +85
°C
–65 to +150
°C
RECOMMENDED OPERATING CONDITIONS
LIMITS
SYMBOL
PARAMETER
MIN
NOM
MAX
5.0
5.5
UNIT
VCC
Supply voltage
4.5
V
VIH
High-level input voltage
2.0
VIL
Low-level input voltage
0.8
V
IIK
Input clamp current
–18
mA
IOH
High-level output current
–1
mA
IOL
Low-level output current
20
mA
Tamb
Operating free-air
free air temperature range
V
Commercial range
0
+70
°C
Industrial range
–40
+85
°C
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
SYMBOL
TEST CONDITIONS1
PARAMETER
LIMITS
MIN
2.5
VIH = MIN, IOH = MAX
±5%VCC
2.7
VCC = MIN, VIL = MAX
±10%VCC
0.35
0.50
VIH = MIN, IOL = MAX
±5%VCC
0.35
0.50
–0.73
–1.2
V
VCC = MAX, VI = 7.0V
100
µA
VCC = MAX, VI = 2.7V
20
µA
–0.6
mA
–2.4
mA
–3.0
mA
–150
mA
VOL
O
Low level output voltage
Low-level
VIK
Input clamp voltage
VCC = MIN, II = IIK
II
Input current at maximum input voltage
IIH
High-level input current
Jn, Kn
CPn
VCC = MAX, VI = 0.5V
SDn, RDn
IOS
Short-circuit output
current3
UNIT
±10%VCC
High level output voltage
High-level
Low-level input current
MAX
VCC = MIN, VIL = MAX
VOH
O
IIL
TYP2
VCC = MAX
–60
V
3.4
V
ICC
Supply current (total)4
VCC = MAX
15
21
mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, Tamb = 25°C.
3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold
techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting
of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any
sequence of parameter tests, IOS tests should be performed last.
4. Measure ICC with the clock input grounded and all outputs open, with the Q and Q outputs High in turn.
February 9, 1990
4
Philips Semiconductors
Product specification
Dual J-K negative edge-triggered flip-flop
74F112
AC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL
VCC = +5.0V ± 10%
Tamb = 0°C to +70°C
CL = 50pF
RL = 500Ω
VCC = +5.0V
Tamb = +25°C
CL = 50pF
RL = 500Ω
TEST
CONDITION
PARAMETER
MIN
TYP
MAX
MIN
MAX
80
VCC = +5.0V ± 10%
Tamb = –40°C to +85°C
CL = 50pF
RL = 500Ω
MIN
UNIT
MAX
fMAX
Maximum clock frequency
Waveform 1
85
100
80
MHz
tPLH
tPHL
Propagation delay
CP to Qn or Qn
Waveform 1
2.0
2.0
5.0
5.0
6.5
6.5
2.0
2.0
7.5
7.5
2.0
2.0
7.5
7.5
ns
tPLH
tPHL
Propagation delay
SDn, RD to Qn or Qn
Waveform 2,3
2.0
2.0
4.5
4.5
6.5
6.5
2.0
2.0
7.5
7.5
1.5
1.5
7.5
7.5
ns
AC SETUP REQUIREMENTS
LIMITS
SYMBOL
VCC = +5.0V ± 10%
Tamb = 0°C to +70°C
CL = 50pF
RL = 500Ω
VCC = +5.0V
Tamb = +25°C
CL = 50pF
RL = 500Ω
TEST
CONDITION
PARAMETER
MIN
TYP
MAX
MIN
MAX
VCC = +5.0V ± 10%
Tamb = –40°C to +85°C
CL = 50pF
RL = 500Ω
MIN
UNIT
MAX
tS(H)
tS((L)
Setup time, High or Low
Jn, Kn to CP
Waveform 1
4.0
3.5
5.0
4.0
5.0
4.0
ns
th(H)
th(L)
Hold time, High or Low
Jn, Kn to CP
Waveform 1
0.0
0.0
0.0
0.0
0.0
0.0
ns
tW(H)
tW(L)
CP Pulse width
High or Low
Waveform 1
4.5
4.5
5.0
5.0
5.0
5.0
ns
tW(L)
SDn, RD Pulse width
Low
Waveform 2,3
4.5
5.0
5.0
ns
tREC
Recovery time
SDn, RD to CP
Waveform 2,3
4.5
5.0
5.0
ns
AC WAVEFORMS
For all waveforms, VM = 1.5V.
Jn, Kn
VM
ts(L)
VM
VM
ts(H)
th(L)
VM
th(H)
fmax
CPn
VM
tw(L)
VM
tw(H)
tPHL
tPLH
Qn
VM
VM
tPLH
tPHL
Qn
VM
VM
VM
SF00107
The shaded areas indicate when the input is permitted to change for predictable output performance.
Waveform 1. Propagation Delay for Data to Output, Data Setup Time and Hold Times, and Clock Pulse Width
February 9, 1990
5
Philips Semiconductors
Product specification
Dual J-K negative edge-triggered flip-flop
74F112
Jn, Kn
SDn
VM
tw(L)
VM
tREC
CPn
VM
tPLH
Qn
VM
tPHL
VM
Qn
SF00108
Waveform 2. Propagation Delay for Set to Output, Set Pulse Width, and Recovery Time for Set to Clock
Jn, Kn
RDn
VM
tw(L)
VM
tREC
CPn
VM
tPHL
Qn
VM
tPLH
Qn
VM
SF00109
Waveform 3. Propagation Delay for Reset to Output, Reset Pulse Width, and Recovery Time for Reset to Clock
February 9, 1990
6
Philips Semiconductors
Product specification
Dual J-K negative edge-triggered flip-flop
74F112
TEST CIRCUIT AND WAVEFORMS
VCC
VIN
tw
90%
NEGATIVE
PULSE
VM
D.U.T.
RT
CL
RL
AMP (V)
VM
10%
VOUT
PULSE
GENERATOR
90%
10%
tTHL (tf )
tTLH (tr )
tTLH (tr )
tTHL (tf )
0V
AMP (V)
90%
90%
POSITIVE
PULSE
Test Circuit for Totem-Pole Outputs
DEFINITIONS:
RL = Load resistor;
see AC ELECTRICAL CHARACTERISTICS for value.
CL = Load capacitance includes jig and probe capacitance;
see AC ELECTRICAL CHARACTERISTICS for value.
RT = Termination resistance should be equal to ZOUT of
pulse generators.
VM
VM
10%
10%
tw
0V
Input Pulse Definition
INPUT PULSE REQUIREMENTS
family
amplitude VM
74F
3.0V
1.5V
rep. rate
tw
tTLH
tTHL
1MHz
500ns
2.5ns
2.5ns
SF00006
February 9, 1990
7
Philips Semiconductors
Product specification
Dual J-K negative edge-triggered flip-flop
DIP16: plastic dual in-line package; 16 leads (300 mil)
1990 Feb 09
8
74F112
SOT38-4
Philips Semiconductors
Product specification
Dual J-K negative edge-triggered flip-flop
SO16: plastic small outline package; 16 leads; body width 3.9 mm
1990 Feb 09
9
74F112
SOT109-1
Philips Semiconductors
Product specification
Dual J-K negative edge-triggered flip-flop
74F112
Data sheet status
Data sheet
status
Product
status
Definition [1]
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
 Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
print code
Document order number:
yyyy mmm dd
10
Date of release: 10-98
9397-750-05071