PHILIPS P80C652

INTEGRATED CIRCUITS
80C652/83C652
CMOS single-chip 8-bit microcontrollers
Product specification
IC20 Data Handbook
1996 Aug 15
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
DESCRIPTION
80C652/83C652
PIN CONFIGURATIONS
The P80C652/83C652 Single-Chip 8-Bit
Microcontroller is manufactured in an
advanced CMOS process and is a derivative
of the 80C51 microcontroller family. The
80C652/83C652 has the same instruction set
as the 80C51. Three versions of the
derivative exist:
83C652 — 8k bytes mask programmable
ROM
87C652 — EPROM version (described in a
separate chapter)
• 80C51 central processing unit
• 8k × 8 ROM expandable externally to
P1.1 2
39 P0.0/AD0
38 P0.1/AD1
P1.3 4
37 P0.2/AD2
P1.4 5
36 P0.3/AD3
P1.5 6
35 P0.4/AD4
SCL/P1.6 7
34 P0.5/AD5
SDA/P1.7 8
33 P0.6/AD6
RST 9
64k bytes
This device provides architectural
enhancements that make it applicable in a
variety of applications for general control
systems. The 8XC652 contains a non-volatile
8k × 8 read-only program memory, a volatile
256 × 8 read/write data memory, four 8-bit I/O
ports, two 16-bit timer/event counters
(identical to the timers of the 80C51), a
multi-source, two-priority-level, nested
interrupt structure, an I2C interface, UART
and on-chip oscillator and timing circuits. For
systems that require extra capability, the
8XC652 can be expanded using standard
TTL compatible memories and logic.
The device also functions as an arithmetic
processor having facilities for both binary and
BCD arithmetic plus bit-handling capabilities.
The instruction set consists of over 100
instructions: 49 one-byte, 45 two-byte and 17
three-byte. With a 16(24)MHz crystal, 58% of
the instructions are executed in 0.75(0.5)µs
and 40% in 1.5(1)µs. Multiply and divide
instructions require 3(2)µs.
• 256 × 8 RAM, expandable externally to
64k bytes
• Two standard 16-bit timer/counters
• Four 8-bit I/O ports
• I2C-bus serial I/O port with byte oriented
master and slave functions
• Full-duplex UART facilities
• Power control modes
– Idle mode
– Power-down mode
• ROM code protection
• Extended frequency range: 1.2 to 24 MHz
• Three operating ambient temperature
40 V
DD
P1.2 3
FEATURES
80C652 — ROMless version
P1.0 1
RxD/P3.0 10
PLASTIC
DUAL
IN-LINE
PACKAGE
32 P0.7/AD7
31 EA
TxD/P3.1 11
30 ALE
INT0/P3.2 12
29 PSEN
INT1/P3.3 13
28 P2.7/A15
T0/P3.4 14
27 P2.6/A14
T1/P3.5 15
26 P2.5/A13
WR/P3.6 16
25 P2.4/A12
RD/P3.7 17
24 P2.3/A11
XTAL2 18
23 P2.2/A10
XTAL1 19
22 P2.1/A9
20
21 P2.0/A8
VSS
ranges:
0 to +70°C
–40 to +85°C
–40 to +125°C
6
1
40
7
39
PLASTIC
LEADED
CHIP
CARRIER
LOGIC SYMBOL
VDDVSS
XTAL1
XTAL2
EA
PSEN
PORT 0
RST
ADDRESS AND
DATA BUS
17
29
18
28
ALE
34
1
33
PLASTIC
QUAD
FLAT
PACK
ADDRESS BUS
PORT 2
SCL
SDA
RxD
TxD
INT0
INT1
T0
T1
WR
RD
1996 Aug 15
PORT 1
PORT 3
ALTERNATE
FUNCTIONS
44
11
23
12
2
22
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
CERAMIC AND PLASTIC LEADED
CHIP CARRIER PIN FUNCTIONS
6
1
PLASTIC QUAD FLAT PACK
PIN FUNCTIONS
44
40
7
39
33
PLASTIC
QUAD
FLAT
PACK
17
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
11
29
Function
NC*
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6/SCL
P1.7/SDA
RST
P3.0/RxD
NC*
P3.1/TxD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
P3.6/WR
P3.7/RD
XTAL2
XTAL1
VSS
*DO NOT CONNECT
34
1
CERAMIC
AND
PLASTIC
LEADED CHIP
CARRIER
18
80C652/83C652
28
Pin
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
23
12
Function
NC*
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P2.4/A12
P2.5/A13
P2.6/A14
P2.7/A15
PSEN
ALE
NC*
EA
P0.7/AD7
P0.6/AD6
P0.5/AD5
P0.4/AD4
P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
VDD
22
Pin
1
2
3
4
5
6
7
Function
P1.5
P1.6/SCL
P1.7/SDA
RST
P3.0/RxD
VSS4
P3.1/TxD
Pin
23
24
25
26
27
28
29
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
P3.6/WR
P3.7/RD
XTAL2
XTAL1
VSS1
NC*
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P2.4/A12
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Function
P2.5/A13
P2.6/A14
P2.7/A15
PSEN
ALE
VSS2
EA/VPP
P0.7/AD7
P0.6/AD6
P0.5/AD5
P0.4/AD4
P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
VDD
VSS3
P1.0
P1.1
P1.2
P1.3
P1.4
*DO NOT CONNECT
NOTES TO QFP ONLY:
1. Due to EMC improvements, all VSS pins
(6, 16, 28, 39) must be connected to VSS
on the 80C652/83C652.
1996 Aug 15
3
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
ORDER INFORMATION
PHILIPS
PART ORDER NUMBER
PART MARKING
PHILIPS NORTH AMERICA
PART ORDER NUMBER
TEMPERATURE
RANGE (°C)
FREQ
ROMless
ROM3
Drawing
Number
ROMless
ROM
AND PACKAGE
MHz1,2
P80C652FBP
P83C652FBP/xxx
SOT129-1
P80C652FBPN
P83C652FBPN
0 to +70, Plastic Dual In-line Package
16
P80C652FBA
P83C652FBA/xxx
SOT187-2
P80C652FBAA
P83C652FBAA
0 to +70, Plastic Leaded Chip Carrier
16
P80C652FBB
P83C652FBB/xxx
SOT307-2 4
P80C652FBBB
P83C652FBBB
0 to +70, Plastic Quad Flat Pack
16
P80C652FFP
P83C652FFP/xxx
SOT129-1
P80C652FFPN
P83C652FFPN
–40 to +85, Plastic Dual In-line Package
16
P80C652FFA
P83C652FFA/xxx
SOT187-2
P80C652FFAA
P83C652FFAA
–40 to +85, Plastic Leaded Chip Carrier
16
P80C652FFB
P83C652FFB/xxx
SOT307-2 4
P80C652FFBB
P83C652FFBB
–40 to +85, Plastic Quad Flat Pack
16
P80C652FHP
P83C652FHP/xxx
SOT129-1
P80C652FHPN
P83C652FHPN
–40 to +125, Plastic Dual In-line Package
16
P80C652FHA
P83C652FHA/xxx
SOT187-2
P80C652FHAA
P83C652FHAA
–40 to +125, Plastic Leaded Chip Carrier
16
P80C652FHBB
P83C652FHBB
–40 to +125, Plastic Quad Flat Pack
16
SOT307-2
4
P80C652FHB
P83C652FHB/xxx
P80C652IBP
P83C652IBP/xxx
SOT129-1
P80C652IBPN
P83C652IBPN
0 to +70, Plastic Dual In-line Package
24
P80C652IBA
P83C652IBA/xxx
SOT187-2
P80C652IBAA
P83C652IBAA
0 to +70, Plastic Leaded Chip Carrier
24
SOT307-2
4
P80C652IBB
P83C652IBB/xxx
P80C652IBBB
P83C652IBBB
0 to +70, Plastic Quad Flat Pack
24
P80C652IFP
P83C652IFP/xxx
SOT129-1
P80C652IFPN
P83C652IFPN
–40 to +85, Plastic Dual In-line Package
24
P80C652IFA
P83C652IFA/xxx
SOT187-2
P80C652IFAA
P83C652IFAA
–40 to +85, Plastic Leaded Chip Carrier
24
P80C652IFB
P83C652IFB/xxx
SOT307-2 4
P80C652IFBB
P83C652IFBB
–40 to +85, Plastic Quad Flat Pack
24
NOTES:
1. 80C652 and 83C652 frequency range is 1.2MHz–16MHz or 1.2 to 24MHz.
2. For specification of the EPROM version, see the 87C652 data sheet.
3. xxx denotes the ROM code number.
4. SOT311 replaced by SOT307-2.
1996 Aug 15
4
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
TEMPERATURE
RANGE (°C)
FREQ
Drawing
Number
AND PACKAGE
MHz1,2
S87C652-4N40
SOT129-1
0 to +70, Plastic Dual In-line Package
16
S87C652-4F40
0590B
0 to +70, Ceramic Dual In-line
Package w/Window
16
S87C652-4A44
SOT187-2
0 to +70, Plastic Leaded Chip Carrier
16
S87C652-4K44
1472A
0 to +70, Ceramic Leaded Chip Carrier
w/Window
16
S87C652-4B44
SOT307-2
0 to +70, Plastic Quad Flat Pack
16
S87C652-5N40
SOT129-1
–40 to +85, Plastic Dual In-line Package
16
S87C652-5F40
0590B
–40 to +85, Ceramic Dual In-line Package
w/Window
16
S87C652-5A44
SOT187-2
–40 to +85, Plastic Leaded Chip Carrier
16
S87C652-5B44
SOT307-2
–40 to +85, Plastic Quad Flat Pack
16
S87C652-7N40
SOT129-1
0 to +70, Plastic Dual In-line Package
20
S87C652-7F40
0590B
0 to +70, Ceramic Dual In-line Package
w/Window
20
S87C652-7A44
SOT187-2
0 to +70, Plastic Leaded Chip Carrier
20
S87C652-7K44
1472A
0 to +70, Ceramic Leaded Chip Carrier
w/Window
20
S87C652-8N40
SOT129-1
–40 to +85, Plastic Dual In-line Package
20
S87C652-8F40
0590B
–40 to +85, Ceramic Dual In-line Package
w/Window
20
S87C652-8A44
SOT187-2
–40 to +85, Plastic Leaded Chip Carrier
20
EPROM2
1996 Aug 15
5
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
BLOCK DIAGRAM
FREQUENCY
REFERENCE
XTAL2
COUNTERS
XTAL1
OSCILLATOR
AND
TIMING
T0
PROGRAM
MEMORY
(8K x 8 ROM)
DATA
MEMORY
(256 x 8 RAM)
T1
TWO 16-BIT
TIMER/EVENT
COUNTERS
SDA
I2C SERIAL I/O
CPU
SCL
INTERNAL
INTERRUPTS
64K BYTE BUS
EXPANSION
CONTRTOL
INT0
INT1
CONTROL
PROGRAMMABLE I/O
PARALLEL PORTS,
ADDRESS/DATA BUS
AND I/O PINS
EXTERNAL
INTERRUPTS
1996 Aug 15
6
PROG SERIAL PORT
FULL DUPLEX UART
SYNCHRONOUS SHIFT
SERIAL IN
SERIAL OUT
SHARED WITH
PORT 3
SHARED
WITH
PORT 1
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
PIN DESCRIPTIONS
PIN NUMBER
MNEMONIC
DIP
PLCC
QFP
TYPE
VSS
20
22
6, 16,
28, 39
I
Ground: 0V reference. With the QFP package all VSS pins (VSS1 to VSS4) must be
connected.
VDD
40
44
38
I
Power Supply: This is the power supply voltage for normal, idle, and power-down
operation.
39–32
43–36
37–30
I/O
Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to
them float and can be used as high-impedance inputs. Port 0 is also the multiplexed
low-order address and data bus during accesses to external program and data memory. In
this application, it uses strong internal pull-ups when emitting 1s.
1–8
2–9
40–44,
1–3
I/O
7
8
8
9
2
3
I/O
I/O
Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups, except P1.6 and P1.7
which are open drain. Port 1 pins that have 1s written to them are pulled high by the
internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled
low will source current because of the internal pull-ups. (See DC Electrical Characteristics:
IIL). Alternate functions include:
SCL: I2C-bus serial port clock line.
SDA: I2C-bus serial port data line.
P2.0–P2.7
21–28
24–31
18–25
I/O
Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 2 pins that are externally being pulled low will source current because of the
internal pull-ups. (See DC Electrical Characteristics: IIL). Port 2 emits the high-order
address byte during fetches from external program memory and during accesses to
external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it
uses strong internal pull-ups when emitting 1s. During accesses to external data memory
that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2 special function
register.
P3.0–P3.7
10–17
11,
13–19
5,
7–13
I/O
10
11
12
13
14
15
16
17
11
13
14
15
16
17
18
19
5
7
8
9
10
11
12
13
I
O
I
I
I
I
O
O
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 3 pins that are externally being pulled low will source current because of the
pull-ups. (See DC Electrical Characteristics: IIL). Port 3 also serves the special features of
the 80C51 family, as listed below:
RxD (P3.0): Serial input port
TxD (P3.1): Serial output port
INT0 (P3.2): External interrupt
INT1 (P3.3): External interrupt
T0 (P3.4): Timer 0 external input
T1 (P3.5): Timer 1 external input
WR (P3.6): External data memory write strobe
RD (P3.7): External data memory read strobe
RST
9
10
4
I
Reset: A high on this pin for two machine cycles while the oscillator is running, resets the
device. An internal diffused resistor to VSS permits a power-on reset using only an external
capacitor to VDD.
ALE
30
33
27
I/O
Address Latch Enable: Output pulse for latching the low byte of the address during an
access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6
the oscillator frequency. Note that one ALE pulse is skipped during each access to external
data memory.
PSEN
29
32
26
O
Program Store Enable: Read strobe to external program memory via Port 0 and Port 2. It
is activated twice each machine cycle during fetches from the external program memory.
When executing out of external program memory two activations of PSEN are skipped
during each access to external data memory. PSEN is not activated (remains HIGH) during
no fetches from external program memory. PSEN can sink/source 8 LSTTL inputs and can
drive CMOS inputs without external pull–ups.
EA
31
35
29
I
External Access: If during a RESET, EA is held at TTL, level HIGH, the CPU executes out
of the internal program memory ROM provided the Program Counter is less than 8192. If
during a RESET, EA is held a TTL LOW level, the CPU executes out of external program
memory. EA is not allowed to float.
XTAL1
19
21
15
I
Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator
circuits.
P0.0–0.7
P1.0–P1.7
P1.6
P1.7
NAME AND FUNCTION
XTAL2
18
20
14
O
Crystal 2: Output from the inverting oscillator amplifier.
NOTE:
To avoid “latch-up” effect at power-on, the voltage on any pin at any time must not be higher than VDD + 0.5V or VSS – 0.5V, respectively.
1996 Aug 15
7
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
Table 1.
SYMBOL
80C652/83C652
8XC652/654 Special Function Registers
DESCRIPTION
DIRECT
BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION
ADDRESS MSB
LSB
RESET
VALUE
ACC*
Accumulator
E0H
E7
E6
E5
E4
E3
E2
E1
E0
00H
B*
B register
F0H
F7
F6
F5
F4
F3
F2
F1
F0
00H
DPTR:
Data pointer
(2 bytes)
Data pointer high
Data pointer low
83H
82H
IE*#
Interrupt enable
A8H
IP*#
Interrupt priority
B8H
–
87
86
85
84
83
82
81
80
P0*
Port 0
80H
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
97
96
95
94
93
92
91
90
P1*#
Port 1
90H
SDA
SCL
A7
A6
A5
A4
A3
A2
A1
A0
P2*
Port 2
A0H
A15
A14
A13
A12
A11
A10
A9
A8
B7
B6
B5
B4
B3
B2
B1
B0
DPH
DPL
00H
00H
AF
AE
EA
BF
BE
AD
AC
AB
AA
A9
A8
ES1
ES0
ET1
EX1
ET0
EX0
BD
BC
BB
BA
B9
B8
PS1
PS0
PT1
PX1
PT0
PX0
0x000000B
xx000000B
FFH
FFH
FFH
P3*
Port 3
B0H
RD
WR
T1
T0
INT1
INT0
TXD
RXD
FFH
PCON
Power control
87H
SMOD
–
–
–
GF1
GF0
PD
IDL
0xxx0000B
9F
9E
9D
9C
9B
9A
99
98
S0CON*#
Serial 0 port control
98H
SM0
SM1
SM2
REN
TB8
RB8
TI
RI
S0BUF#
Serial 0 data buffer
99H
D7
D6
D5
D4
D3
D2
D1
D0
CY
AC
F0
RS1
RS0
OV
F1
P
00H
xxxxxxxxB
PSW*
Program status word
D0H
S1DAT#
Serial 1 data
DAH
SP
Stack pointer
81H
S1ADR#
Serial 1 address
DBH
 SLAVE ADDRESS 
S1STA#
Serial 1 status
D9H
SC4
DF
DE
S1CON*#
Serial 1 control
D8H
CR2
ENS1
8F
8E
8D
8C
8B
8A
89
88
TCON*
Timer control
88H
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
TH1
Timer high 1
8DH
00H
TH0
Timer high 0
8CH
00H
TL1
Timer low 1
8BH
00H
TL0
Timer low 0
8AH
00H
00H
07H
TMOD
Timer mode
89H
GATE
* SFRs are bit addressable.
# SFRs are modified from or added to the 80C51 SFRs.
1996 Aug 15
00H
SC3
C/T
SC2
00H
0
F8H
SC1
SC0
0
DD
DC
DB
DA
D9
D8
STA
STO
SI
AA
CR1
CR0
M1
8
M0
GATE
C/T
0
GC
M1
M0
00000000B
00H
00H
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
ROM CODE PROTECTION
(83C652)
The 8XC652 has an additional security
feature. ROM code protection may be
selected by setting a mask–programmable
security bit (i.e., user dependent). This
feature may be requested during ROM code
submission. When selected, the ROM code is
protected and cannot be read out at any time
by any test mode or by any instruction in the
external program memory space.
The MOVC instructions are the only
instructions that have access to program
code in the internal or external program
memory. The EA input is latched during
RESET and is “don’t care” after RESET
(also if the security bit is not set). This
implementation prevents reading internal
program code by switching from external
program memory to internal program memory
during a MOVC instruction or any other
instruction that uses immediate data.
To drive the device from an external clock
source, XTAL1 should be driven while XTAL2
is left unconnected. There are no
requirements on the duty cycle of the
external clock signal, because the input to
the internal clock circuitry is through a
divide-by-two flip-flop. However, minimum
and maximum high and low times specified in
the data sheet must be observed.
Reset
A reset is accomplished by holding the RST
pin high for at least two machine cycles (24
oscillator periods), while the oscillator is
running. To insure a good power-on reset, the
RST pin must be high long enough to allow
the oscillator time to start up (normally a few
milliseconds) plus two machine cycles. At
power-on, the voltage on VDD and RST must
come up at the same time for a proper
start-up.
Idle Mode
In the idle mode, the CPU puts itself to sleep
while all of the on-chip peripherals stay
active. The instruction to invoke the idle
mode is the last instruction executed in the
normal operating mode before the idle mode
is activated. The CPU contents, the on-chip
RAM, and all of the special function registers
remain intact during this mode. The idle
mode can be terminated either by any
OSCILLATOR
CHARACTERISTICS
XTAL1 and XTAL2 are the input and output,
respectively, of an inverting amplifier. The
pins can be configured for use as an on-chip
oscillator, as shown in the Logic Symbol,
page 2.
Table 2.
80C652/83C652
enabled interrupt (at which time the process
is picked up at the interrupt service routine
and continued), or by a hardware reset which
starts the processor in the same manner as a
power-on reset.
Power-Down Mode
In the power-down mode, the oscillator is
stopped and the instruction to invoke
power-down is the last instruction executed.
Only the contents of the on-chip RAM are
preserved. A hardware reset is the only way
to terminate the power-down mode. The
control bits for the reduced power modes are
in the special function register PCON. Table 2
shows the state of the I/O ports during low
current operating modes.
I2C Serial Communication—SIO1
The I2C serial port is identical to the I2C
serial port on the 8XC552. The operation of
this subsystem is described in detail in the
8XC552 section of this manual.
Note that in both the 8XC652/4 and the
8XC552 the I2C pins are alternate functions
to port pins P1.6 and P1.7. Because of this,
P1.6 and P1.7 on these parts do not have a
pull-up structure as found on the 80C51.
Therefore P1.6 and P1.7 have open drain
outputs on the 8XC652/4.
External Pin Status During Idle and Power-Down Mode
PROGRAM
MEMORY
ALE
PSEN
PORT 0
PORT 1
PORT 2
PORT 3
Idle
Internal
1
1
Data
Data
Data
Data
Idle
External
1
1
Float
Data
Address
Data
Power-down
Internal
0
0
Data
Data
Data
Data
Power-down
External
0
0
Float
Data
Data
Data
MODE
Serial Control Register (S1CON) – See Table 3
S1CON (D8H)
CR2
ENS1
STA
STO
SI
AA
CR1
CR0
Bits CR0, CR1 and CR2 determine the serial clock frequency that is generated in the master mode of operation.
Table 3.
Serial Clock Rates
BIT FREQUENCY (kHz) AT fOSC
CR2
CR1
CR0
6MHz
12MHz
16MHz
24MHz
fOSC DIVIDED BY
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
23
27
31.25
37
6.25
50
100
0.24 < 62.5
0 to 255
47
54
62.5
75
12.5
100
2001
0.49 < 62.5
0 to 254
62.5
71
83.3
100
17
1331
2671
0.65 < 55.6
0 to 253
94
1071
1251
1501
25
2001
4001
0.98 < 50.0
0 to 251
256
224
192
160
960
120
60
96 × (256 – (reload value Timer 1))
reload value range Timer 1 (in mode 2)
NOTES:
1. These frequencies exceed the upper limit of 100kHz of the I2C-bus specification and cannot be used in an I2C-bus application.
1996 Aug 15
9
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
ABSOLUTE MAXIMUM RATINGS1, 2, 3
RATING
UNIT
Storage temperature range
–65 to +150
°C
Voltage on any other pin to VSS
–0.5 to + 6.5
V
Input, output current on any single pin
±5
mA
Power dissipation (based on package heat transfer
limitations, not device power consumption)
1
W
PARAMETER
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent
damage to the device. This is a stress rating only and functional operation of the device at
these or any conditions other than those described in the AC and DC Electrical
Characteristics section of this specification is not implied.
2. This product includes circuitry specifically designed for the protection of its internal devices
from the damaging effects of excessive static charge. Nonetheless, it is suggested that
conventional precautions be taken to avoid applying greater than the rated maxima.
3. Parameters are valid over operating temperature range unless otherwise specified. All
voltages are with respect to VSS unless otherwise noted.
DEVICE SPECIFICATIONS
SUPPLY VOLTAGE
(V)
FREQUENCY
(MHz)
MIN.
MAX.
MIN.
MAX.
TEMPERATURE
RANGE
(°C)
P8XC652FBx
4.0
6.0
1.2
16
0 to +70
TYPE
P8XC652FFx
4.0
6.0
1.2
16
–40 to +85
P8XC652FHx
4.5
5.5
1.2
16
–40 to +125
P8XC652IBx
4.5
5.5
1.2
24
0 to +70
P83X652IFx
4.5
5.5
1.2
24
–40 to +85
1996 Aug 15
10
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
DC ELECTRICAL CHARACTERISTICS
VSS = 0V
TEST
SYMBOL
VIL
PARAMETER
PART TYPE
Input low voltage,
except EA, P1.6/SCL, P1.7/SDA
VIL1
Input low voltage to EA
VIL2
Input low voltage to P1.6/SCL, P1.7/SDA6
VIH
Input high voltage, except XTAL1, RST,
P1.6/SCL, P1.7/SDA
CONDITIONS
LIMITS
MIN.
MAX.
UNIT
0 to +70°C
–40 to +85°C
–40 to +125°C
–0.5
–0.5
–0.5
0.2VDD–0.1
0.2VDD–0.15
0.2VDD–0.25
V
V
V
0 to +70°C
–40 to +85°C
–40 to +125°C
–0.5
–0.5
–0.5
0.2VDD–0.3
0.2VDD–0.35
0.2VDD–0.45
V
V
V
–0.5
0.3VDD
V
0 to +70°C
–40 to +85°C
–40 to +125°C
0.2VDD+0.9
0.2VDD+1.0
0.2VDD+1.0
VDD+0.5
VDD+0.5
VDD+0.5
V
V
V
0 to +70°C
–40 to +85°C
–40 to +125°C
0.7VDD
0.7VDD+0.1
0.7VDD+0.1
VDD+0.5
VDD+0.5
VDD+0.5
V
V
V
VIH1
Input high voltage, XTAL1, RST
VIH2
Input high voltage, P1.6/SCL, P1.7/SDA6
6.0
V
VOL
Output low voltage, ports 1, 2, 3,
except P1.6/SCL, P1.7/SDA
IOL = 1.6mA8, 9
0.45
V
VOL1
Output low voltage, port 0, ALE, PSEN
IOL = 3.2mA8, 9
0.45
V
VOL2
Output low voltage, P1.6/SCL, P1.7/SDA
IOL = 3.0mA
0.4
V
0.7VDD
VOH
Output high voltage, ports 1, 2, 3, ALE,
PSEN10
IOH = –60µA
IOH = –25µA
IOH = –10µA
2.4
0.75VDD
0.9VDD
V
V
V
VOH1
Output high voltage; port 0 in external bus mode
IOH = –800µA
IOH = –300µA
IOH = –80µA
2.4
0.75VDD
0.9VDD
V
V
V
IIL
Logical 0 input current, ports 1, 2, 3,
except P1.6/SCL, P1.7/SDA
ITL
Logical 1-to-0 transition current, ports 1, 2, 3,
except P1.6/SCL, P1.7/SDA
0 to +70°C
–40 to +85°C
–40 to +125°C
VIN = 0.45V
–50
–75
–75
µA
µA
µA
0 to +70°C
–40 to +85°C
–40 to +125°C
See note 7
–650
–750
–750
µA
µA
µA
IL1
Input leakage current, port 0, EA
0.45V < VI < VDD
±10
µA
IL2
Input leakage current, P1.6/SCL, P1.7/SDA
0V < VI < 6.0V
0V < VDD < 6.0V
±10
µA
µA
IDD
Power supply current:
Active mode @ 16MHz2, 11
Active mode @ 24MHz2, 11
Idle mode @ 16MHz3, 11
Idle mode @ 24MHz3, 11
Power down mode4, 5
Power down mode4, 5
26.5
33.8
6
7
50
100
mA
mA
mA
mA
µA
µA
RRST
Internal reset pull-down resistor
CIO
Pin capacitance
See note 1
VDD=6.0V
VDD=5.5V
–40 to +125°C
50
Freq.=1MHz
NOTES ON NEXT PAGE.
1996 Aug 15
11
150
kΩ
10
pF
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
NOTES FOR DC ELECTRICAL CHARACTERISTICS:
1. See Figures 9 through 11 for IDD test conditions.
2. The operating supply current is measured with all output pins disconnected; XTAL1 driven with tr = tf = 5ns;
VIL = VSS + 0.5V; VIH = VDD –0.5V; XTAL2 not connected; EA = RST = Port 0 = P1.6 = P1.7 = VDD. See Figure 9.
3. The idle mode supply current is measured with all output pins disconnected; XTAL1 driven with tr = tf = 5ns; VIL = VSS + 0.5V;
VIH = VDD –0.5V; XTAL2 not connected; Port 0 = P1.6 = P1.7 = VDD; EA = RST = VSS. See Figure 10.
4. The power-down current is measured with all output pins disconnected; XTAL2 not connected; Port 0 = P1.6 = P1.7 = VDD;
EA = RST = VSS. See Figure 11.
5. 2V ≤ VPD ≤ VDDmax.
6. The input threshold voltage of P1.6 and P1.7 (SIO1) meets the I2C specification, so an input voltage below 0.3VDD will be recognized as a
logic 0 while an input voltage above 0.7VDD will be recognized as a logic 1.
7. Pins of ports 1 , 2, and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
maximum value when VIN is approximately 2V.
8. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the VOLs of ALE and ports 1 and 3. The noise is due
to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the
worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify
ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input.
9. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL = 10mA per port pin; Maximum
IOL = 26mA total for Port 0; Maximum IOL = 15mA total for Ports 1, 2, and 3; Maximum IOL = 71mA total for all output pins. If IOL exceeds the
test conditions, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions.
10. Capacitive loading on ports 0 and 2 may cause the VOH on ALE and PSEN to momentarily fall below the 0.9VDD specification when the
address bits are stabilizing.
11. IDDMAX for other frequencies can be derived from Figure 1, where FREQ is the external oscillator frequency in MHz. IDDMAX is given in mA.
50
40
IDD
(mA)
IDD
(mA)
40
30
30
(1)
20
(1)
20
10
10
(2)
(2)
0
0
4
8
12
0
16
0
4
fXTAL1 (MHz)
8
12
24
fXTAL1 (MHz)
(1) MAXIMUM OPERATING MODE: VDD = VDDmax
(1) MAXIMUM OPERATING MODE: VDD = VDDmax
(2) MAXIMUM IDLE MODE: VDD = VDDmax
(2) MAXIMUM IDLE MODE: VDD = VDDmax
These values are valid within the specified
frequency range.
These values are valid within the specified
frequency range.
Figure 1. IDD vs. Frequency
1996 Aug 15
16
12
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
AC ELECTRICAL CHARACTERISTICS1, 2 (16 MHz type)
16MHz CLOCK
SYMBOL
FIGURE
PARAMETER
MIN
VARIABLE CLOCK
MAX
MIN
MAX
UNIT
1.2
16
MHz
1/tCLCL
2
Oscillator frequency
tLHLL
2
ALE pulse width
85
2tCLCL–40
ns
tAVLL
2
Address valid to ALE low
8
tCLCL–55
ns
tLLAX
2
Address hold after ALE low
28
tLLIV
2
ALE low to valid instruction in
tLLPL
2
ALE low to PSEN low
23
tCLCL–40
tPLPH
2
PSEN pulse width
143
3tCLCL–45
tPLIV
2
PSEN low to valid instruction in
tPXIX
2
Input instruction hold after PSEN
tPXIZ
2
Input instruction float after PSEN
38
tCLCL–25
ns
tAVIV
2
Address to valid instruction in
208
5tCLCL–105
ns
tPLAZ
2
PSEN low to address float
10
10
ns
tCLCL–35
150
ns
4tCLCL–100
83
ns
ns
3tCLCL–105
0
ns
0
ns
ns
Data Memory
tRLRH
3, 4
RD pulse width
275
6tCLCL–100
ns
tWLWH
3, 4
WR pulse width
275
tRLDV
3, 4
RD low to valid data in
tRHDX
3, 4
Data hold after RD
tRHDZ
3, 4
Data float after RD
55
2tCLCL–70
ns
tLLDV
3, 4
ALE low to valid data in
350
8tCLCL–150
ns
tAVDV
3, 4
Address to valid data in
9tCLCL–165
ns
tLLWL
3, 4
ALE low to RD or WR low
138
3tCLCL+50
ns
tAVWL
3, 4
Address valid to WR low or RD low
120
4tCLCL–130
ns
tQVWX
3, 4
Data valid to WR transition
3
tCLCL–60
ns
tDW
3, 4
Data setup time before WR
288
7tCLCL–150
ns
tWHQX
3, 4
Data hold after WR
13
tRLAZ
3, 4
RD low to address float
tWHLH
3, 4
RD or WR high to ALE high
23
tXLXL
5
Serial port clock cycle time3
0.75
12tCLCL
µs
tQVXH
5
Output data setup to clock rising edge3
492
10tCLCL–133
ns
80
2tCLCL–117
ns
0
0
6tCLCL–100
148
ns
5tCLCL–165
0
0
398
238
3tCLCL–50
ns
tCLCL–50
0
103
tCLCL–40
ns
ns
0
ns
tCLCL+40
ns
Shift Register
edge3
tXHQX
5
Output data hold after clock rising
tXHDX
5
Input data hold after clock rising edge3
tXHDV
5
Clock rising edge to input data valid3
6
High time3
20
tCLCX
6
Low
time3
20
tCLCH
6
Rise time3
492
ns
10tCLCL–133
ns
20
tCLCL – tCLCX
ns
20
External Clock
tCHCX
tCHCL
6
Fall
time3
tCLCL – tCHCX
ns
20
20
ns
20
20
ns
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
3. These values are characterized but not 100% production tested.
1996 Aug 15
13
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
AC ELECTRICAL CHARACTERISTICS1, 2 (24 MHz type)
24MHz CLOCK
SYMBOL
FIGURE
PARAMETER
MIN
VARIABLE CLOCK
MAX
MIN
MAX
UNIT
1.2
24
MHz
1/tCLCL
2
Oscillator frequency
tLHLL
2
ALE pulse width
43
2tCLCL–40
ns
tAVLL
2
Address valid to ALE low
17
tCLCL–25
ns
tLLAX
2
Address hold after ALE low
17
tLLIV
2
ALE low to valid instruction in
tLLPL
2
ALE low to PSEN low
17
tCLCL–25
tPLPH
2
PSEN pulse width
80
3tCLCL–45
tPLIV
2
PSEN low to valid instruction in
tPXIX
2
Input instruction hold after PSEN
tPXIZ
2
Input instruction float after PSEN
17
tCLCL–25
ns
tAVIV
2
Address to valid instruction in
128
5tCLCL–80
ns
tPLAZ
2
PSEN low to address float
10
10
ns
tCLCL–25
102
ns
4tCLCL–65
65
ns
ns
3tCLCL–60
0
ns
0
ns
ns
Data Memory
tRLRH
3, 4
RD pulse width
150
6tCLCL–100
tWLWH
3, 4
WR pulse width
150
tRLDV
3, 4
RD low to valid data in
tRHDX
3, 4
Data hold after RD
tRHDZ
3, 4
Data float after RD
55
2tCLCL–28
ns
tLLDV
3, 4
ALE low to valid data in
180
8tCLCL–150
ns
tAVDV
3, 4
Address to valid data in
9tCLCL–165
ns
tLLWL
3, 4
ALE low to RD or WR low
75
3tCLCL+50
ns
tAVWL
3, 4
Address valid to WR low or RD low
92
4tCLCL–75
ns
tQVWX
3, 4
Data valid to WR transition
12
tCLCL–30
ns
tDW
3, 4
Data setup time before WR
162
7tCLCL–130
ns
tWHQX
3, 4
Data hold after WR
17
tRLAZ
3, 4
RD low to address float
tWHLH
3, 4
RD or WR high to ALE high
tXLXL
5
Serial port clock cycle time3
0.5
12tCLCL
µs
tQVXH
5
Output data setup to clock rising edge3
283
10tCLCL–133
ns
23
2tCLCL–60
ns
0
0
6tCLCL–100
118
ns
5tCLCL–90
0
0
210
175
3tCLCL–50
67
tCLCL–25
ns
ns
tCLCL–25
0
17
ns
ns
0
ns
tCLCL+25
ns
Shift Register
edge3
tXHQX
5
Output data hold after clock rising
tXHDX
5
Input data hold after clock rising edge3
tXHDV
5
Clock rising edge to input data valid3
6
High time3
17
tCLCX
6
Low
time3
17
tCLCH
6
Rise time3
283
ns
10tCLCL–133
ns
17
tCLCL – tCLCX
ns
17
External Clock
tCHCX
tCHCL
6
Fall
time3
tCLCL – tCHCX
ns
5
5
ns
5
5
ns
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
3. These values are characterized but not 100% production tested.
1996 Aug 15
14
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
AC ELECTRICAL CHARACTERISTICS – I2C INTERFACE
SYMBOL
PARAMETER
INPUT
OUTPUT
SCL TIMING CHARACTERISTICS
tHD;STA
START condition hold time
≥
14 tCLCL
> 4.0µs1
tLOW
SCL LOW time
≥
16 tCLCL
> 4.7µs1
tHIGH
SCL HIGH time
≥
14 tCLCL
> 4.0µs1
tRC
SCL rise time
tFC
SCL fall time
1µs
–2
≤
0.3µs
< 0.3µs3
≤
SDA TIMING CHARACTERISTICS
tSU;DAT1
Data set-up time
≥
250ns
> 20 tCLCL – tRD
tSU;DAT2
SDA set-up time (before rep. START cond.)
≥
250ns
> 1µs1
tSU;DAT3
SDA set-up time (before STOP cond.)
≥
tHD;DAT
Data hold time
tSU;STA
Repeated START set-up time
tSU;STO
250ns
≥
> 8 tCLCL
0ns
> 8 tCLCL – tFC
≥
14 tCLCL
> 4.7µs1
STOP condition set-up time
≥
14 tCLCL
> 4.0µs1
tBUF
Bus free time
≥
14 tCLCL
> 4.7µs1
tRD
SDA rise time
≤
–2
1µs
tFD
SDA fall time
≤ 0.3µs
< 0.3µs3
NOTES:
1. At 100 kbit/s. At other bit rates this value is inversely proportional to the bit-rate of 100 kbit/s.
2. Determined by the external bus-line capacitance and the external bus-line pull-resistor, this must be < 1µs.
3. Spikes on the SDA and SCL lines with a duration of less than 3 tCLCL will be filtered out. Maximum capacitance on bus-lines SDA and
SCL = 400pF.
4. tCLCL = 1/fOSC = one oscillator clock period at pin XTAL1. For 63ns (42ns) < tCLCL < 285ns (16MHz (24MHz) > fOSC > 3.5MHz) the SI01
interface meets the I2C-bus specification for bit-rates up to 100 kbit/s.
TIMING SIO1 (I2C) INTERFACE
repeated START condition
START or repeated START condition
START condition
tSU;STA
STOP condition
tRD
0.7 VDD
SDA
(INPUT/OUTPUT)
0.3 VDD
tBUF
tFD
tRC
tFC
tSU; STO
0.7 VDD
SCL
(INPUT/OUTPUT)
0.3 VDD
tSU;DAT3
tHD;STA
1996 Aug 15
tLOW
tHIGH
tSU;DAT1
tHD;DAT
15
tSU;DAT2
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
EXPLANATION OF THE AC SYMBOLS
Each timing symbol has five characters. The
first character is always ‘t’ (= time). The other
characters, depending on their positions,
indicate the name of a signal or the logical
status of that signal. The designations are:
A – Address
C – Clock
D – Input data
H – Logic level high
I – Instruction (program memory contents)
L – Logic level low, or ALE
P – PSEN
Q – Output data
R – RD signal
t – Time
V – Valid
W – WR signal
X – No longer a valid logic level
Z – Float
Examples: tAVLL = Time for address valid
to ALE low.
tLLPL = Time for ALE low
to PSEN low.
tLHLL
ALE
tAVLL
tLLPL
tPLPH
tLLIV
tPLIV
PSEN
tLLAX
tPXIZ
tPLAZ
tPXIX
A0–A7
PORT 0
A0–A7
INSTR IN
tAVIV
PORT 2
A8–A15
A8–A15
Figure 2. External Program Memory Read Cycle
ALE
tWHLH
PSEN
tLLDV
tLLWL
tRLRH
RD
tAVLL
PORT 0
tLLAX
tRLAZ
tRHDZ
tRLDV
tRHDX
A0–A7
FROM RI OR DPL
DATA IN
A0–A7 FROM PCL
tAVWL
tAVDV
PORT 2
P2.0–P2.7 OR A8–A15 FROM DPH
Figure 3. External Data Memory Read Cycle
1996 Aug 15
16
A8–A15 FROM PCH
INSTR IN
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
ALE
tWHLH
PSEN
tWLWH
tLLWL
WR
tLLAX
tAVLL
tWHQX
tQVWX
tDW
A0–A7
FROM RI OR DPL
PORT 0
DATA OUT
A0–A7 FROM PCL
INSTR IN
tAVWL
PORT 2
P2.0–P2.7 OR A8–A15 FROM DPH
A8–A15 FROM PCH
Figure 4. External Data Memory Write Cycle
INSTRUCTION
0
1
2
3
4
5
6
7
8
ALE
tXLXL
CLOCK
tXHQX
tQVXH
OUTPUT DATA
WRITE TO SBUF
tXHDX
tXHDV
SET TI
INPUT DATA
VALID
VALID
VALID
VALID
VALID
VALID
VALID
VALID
CLEAR RI
SET RI
Figure 5. Shift Register Mode Timing
1996 Aug 15
17
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
VIH1
0.8V
tCHCL
tCHCX
tCLCH
tCLCX
tCLCL
Figure 6. External Clock Drive at XTAL1
VDD–0.5
VLOAD+0.1V
0.2VDD+0.9
VLOAD
0.45V
0.2VDD–0.1
VLOAD–0.1V
VOH–0.1V
VOL+0.1V
NOTE:
FOR TIMING PURPOSES, A PORT IS NO LONGER FLOATING WHEN A 100MV
CHANGE FROM LOAD VOLTAGE OCCURS, AND BEGINS TO FLOAT WHEN A
100mV CHANGE FROM THE LOADED V OH/VOL LEVEL OCCURS. IOH/IOL > +
20mA.
NOTE:
AC INPUTS DURING TESTING ARE DRIVEN AT VDD–0.5 FOR A LOGIC ‘1’ AND
0.45V FOR A LOGIC ‘0’. TIMING MEASUREMENTS ARE MADE AT VIH MIN FOR A
LOGIC ‘1’ AND VIL MAX FOR A LOGIC ‘0’.
Figure 7. AC Testing Input/Output
1996 Aug 15
TIMING
REFERENCE
POINTS
Figure 8. Float Waveform
18
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
VDD
VDD
IDD
IDD
VDD
VDD
VDD
VDD
EA
P0
RST
VDD
RST
P0
EA
(NC)
XTAL2
P1.6
*
*
P1.7
CLOCK SIGNAL
XTAL1
(NC)
XTAL2
CLOCK SIGNAL
P1.6
*
P1.7
*
XTAL1
VSS
VSS
Figure 10. IDD Test Condition, Idle Mode
All other pins are disconnected
Figure 9. IDD Test Condition, Active Mode
All other pins are disconnected
VDD
IDD
VDD
VDD
RST
EA
P0
(NC)
P1.6
XTAL2
P1.7
XTAL1
*
*
VSS
Figure 11. IDD Test Condition, Power Down Mode
All other pins are disconnected. VDD = 2V to 5.5V
NOTE:
* Ports 1.6 and 1.7 should be connected to VCC through resistors of sufficiently high value such that the sink current into these pins does not
exceed the IOL1 specification.
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent
to use the components in the I2C system provided the system conforms to the
I2C specifications defined by Philips. This specification can be ordered using the
code 9398 393 40011.
1996 Aug 15
19
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
DIP40: plastic dual in-line package; 40 leads (600 mil)
1996 Aug 15
20
80C652/83C652
SOT129-1
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
PLCC44: plastic leaded chip carrier; 44 leads
1996 Aug 15
80C652/83C652
SOT187-2
21
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
QFP44: plastic quad flat package; 44 leads (lead length 1.3 mm); body 10 x 10 x 1.75 mm
1996 Aug 15
22
SOT307-2
1996 Aug 15
853–0590B 06688
23
SEATING
PLANE
–T–
–D–
0.023 (0.58)
0.015 (0.38)
0.070 (1.78)
0.050 (1.27)
T
0.100 (2.54) BSC
E D
0.010 (0.254)
2.087 (53.01)
2.038 (51.77)
SEE NOTE 6
0.098 (2.49)
0.040 (1.02)
0.165 (4.19)
0.125 (3.18)
0.015 (0.38)
0.010 (0.25)
0.055 (1.40)
0.020 (0.51)
0.175 (4.45)
0.145 (3.68)
0.695 (17.65)
0.600 (15.24)
BSC
0.600 (15.24)
(NOTE 4)
0.620 (15.75)
0.590 (14.99)
(NOTE 4)
6. Denotes window location for EPROM products.
5. Pin numbers start with Pin #1 and continue
counterclockwise to Pin #40 when viewed
from the top.
0.225 (5.72) MAX.
0.598 (15.19)
0.571 (14.50)
2. Dimension and tolerancing per ANSI Y14. 5M-1982.
3. “T”, “D”, and “E” are reference datums on the body
and include allowance for glass overrun and meniscus
on the seal line, and lid to base mismatch.
4. These dimensions measured with the leads
constrained to be perpendicular to plane T.
NOTES:
1. Controlling dimension: Inches. Millimeters are
shown in parentheses.
0590B
PIN # 1
–E–
0.098 (2.49)
0.040 (1.02)
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
40-PIN (600 mils wide) CERAMIC DUAL IN-LINE (F) PACKAGE (WITH WINDOW (FA) PACKAGE)
1996 Aug 15
853-1472A 05854
24
SEE DETAIL B
SEATING
PLANE
4.83 (0.190)
3.94 (0.155)
8.13 (0.320)
7.37 (0.290)
8.13 (0.320)
7.37 (0.290)
12.7 (0.500)
NOMINAL
40X
1.27 (0.050)
17.65 (0.656)
17.40 (0.685)
3 X 0.63 (0.025) R MIN.
SEE DETAIL A
3
16.89 (0.665)
16.00 (0.630)
4.83 (0.190)
3.94 (0.155)
SEATING
PLANE
6
0.51 (0.02) X 45 °
6
0.38 (0.015)
0.482 (0.019 + 0.002)
BASE PLANE
45 ° TYP.
4 PLACES
0.73 + 0.08 (0.029 + 0.003)
SEATING
PLANE
DETAIL A
TYP. ALL SIDES
mm/(inch)
1.02 + 0.25 (0.040 + 0.010)
1.52 (0.060) REF.
1.27 (0.050) TYP.
17.65 (0.695)
17.40 (0.685)
3.05 (0.120)
2.29 (0.090)
0.25 (0.010)
0.15 (0.006)
0.15 (0.006) MIN.
0.25 (0.010) R MIN.
+ 5°
–10 °
DETAIL B
mm/(inch)
90°
0.508 (0.020) R MIN.
0.076 (0.003) MIN.
6. Backside solder relief is optional and
dimensions are for reference only.
5. All dimensions and tolerances include
lead trim offset and lead plating finish.
3. Dimensions do not include glass protrusion.
Glass protrusion to be 0.005 inches maximum
on each side.
4. Controlling dimension millimeters.
2. UV window is optional.
NOTES:
1. All dimensions and tolerances to conform
to ANSI Y14.5–1982.
1472A
2
1.02 (0.040) X 45°
CHAMFER
45
17.65 (0.695)
17.40 (0.685)
16.89 (0.665)
16.00 (0.630)
3
Phlips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
44-PIN CERQUAD J-BEND (K) PACKAGE
Philips Semiconductors
Product specification
CMOS single-chip 8-bit microcontrollers
80C652/83C652
DEFINITIONS
Data Sheet Identification
Product Status
Definition
Objective Specification
Formative or in Design
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
Preliminary Specification
Preproduction Product
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Product Specification
Full Production
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICATIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Philips Semiconductors and Philips Electronics North America Corporation
register eligible circuits under the Semiconductor Chip Protection Act.
 Copyright Philips Electronics North America Corporation 1996
All rights reserved. Printed in U.S.A.