PHILIPS PCD3755FT

INTEGRATED CIRCUITS
DATA SHEET
PCD3755A; PCD3755E;
PCD3755F
8-bit microcontrollers with DTMF
generator, 8 kbytes OTP and 128
bytes EEPROM
Product specification
Supersedes data of 1996 Dec 18
File under Integrated Circuits, IC03
1997 Apr 16
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
CONTENTS
1
FEATURES
2
GENERAL DESCRIPTION
3
ORDERING INFORMATION
4
BLOCK DIAGRAM
5
PINNING INFORMATION
5.1
5.2
Pinning
Pin description
6
FREQUENCY GENERATOR
6.1
6.2
6.3
6.4
6.5
6.6
Frequency generator derivative registers
Melody output (P1.7/MDY)
Frequency registers
DTMF frequencies
Modem frequencies
Musical scale frequencies
7
EEPROM AND TIMER 2 ORGANIZATION
7.1
7.2
7.3
7.4
7.5
7.6
EEPROM registers
EEPROM latches
EEPROM flags
EEPROM macros
EEPROM access
Timer 2
8
DERIVATIVE INTERRUPTS
9
TIMING
10
RESET
11
IDLE MODE
12
STOP MODE
13
INSTRUCTION SET RESTRICTIONS
14
OVERVIEW OF PORT AND
POWER-ON-RESET CONFIGURATION
15
OTP PROGRAMMING
16
SUMMARY OF DERIVATIVE REGISTERS
17
HANDLING
18
LIMITING VALUES
19
DC CHARACTERISTICS
20
AC CHARACTERISTICS
21
PACKAGE OUTLINES
22
SOLDERING
22.1
22.2
22.3
22.4
Reflow soldering
Wave soldering
DIP
Repairing soldered joints
23
DEFINITIONS
24
LIFE SUPPORT APPLICATIONS
1997 Apr 16
2
PCD3755A; PCD3755E;
PCD3755F
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
1
FEATURES
2
• 8-bit CPU, ROM, RAM, EEPROM and I/O; in a single
28-lead or 32-lead package
PCD3755A; PCD3755E;
PCD3755F
GENERAL DESCRIPTION
This data sheet details the specific properties of the
PCD3755A, PCD3755E and PCD3755F. The devices
differ in their Port and Power-on-reset configurations.
References to ‘PCD3755x’ apply to all three types.
The devices are members of the PCD33xxA family of
microcontrollers.
The shared properties of the family are described in the
“PCD33xxA family” data sheet, which should be read in
conjunction with this publication.
• 8 kbytes user-programmable ROM (One-Time
Programmable)
• 128 bytes RAM
• 128 bytes Electrically Erasable Programmable
Read-Only Memory (EEPROM)
• Over 100 instructions (based on MAB8048) all of 1 or 2
cycles
The PCD3755A, PCD3755E and PCD3755F are
One-Time Programmable (OTP) microcontrollers
designed primarily for telephony applications.They include
an on-chip generator for dual tone multifrequency (DTMF),
modem and musical tones. In addition to dialling,
generated frequencies can be made available as square
waves (P1.7/MDY) for melody generation, providing ringer
operation.
• 20 quasi-bidirectional I/O port lines
• 8-bit programmable Timer/event counter 1
• 8-bit reloadable Timer 2
• Three single-level vectored interrupts:
– external
– 8-bit programmable Timer/event counter 1
The PCD3755A, PCD3755E and PCD3755F also
incorporate 128 bytes of EEPROM. The EEPROM can be
used for storing telephone numbers, particularly for
implementing redial functions.
– derivative; triggered by reloadable Timer 2
• Two test inputs, one of which also serves as the external
interrupt input
• DTMF, modem, musical tone generator
The Power-on-reset circuitry is extra accurate to
accommodate parallel telephones and fax equipment.
• Reference for supply and temperature-independent
tone output
The instruction set is similar to that of the MAB8048 and is
a sub-set of that listed in the “PCD33xxA family” data
sheet.
• Filtering for low output distortion (CEPT compatible)
• Melody output for ringer application
• Power-on-reset
• Stop and Idle modes
• Supply voltage: 1.8 to 6 V (DTMF tone output and
EEPROM erase/write from 2.5 V)
• Clock frequency: 1 to 16 MHz (3.58 MHz for DTMF
suggested)
• Operating temperature: −25 to +70 °C
• Manufactured in silicon gate CMOS process.
3
ORDERING INFORMATION (see note 1)
PACKAGE
TYPE NUMBER
NAME
DESCRIPTION
VERSION
PCD3755xP
DIP28
plastic dual in-line package; 28 leads (600 mil)
SOT117-1
PCD3755xT
SO28
plastic small outline package; 28 leads; body width 7.5 mm
SOT136-1
PCD3755xH
LQFP32
plastic low profile quad flat package; 32 leads; body 7 × 7 × 1.4 mm
SOT358-1
Note
1. Please refer to the Order Entry Form (OEF) for this device for the full type number to use when ordering. This type
number will also specify the required program and the ROM mask options.
1997 Apr 16
3
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
PORT 2
BUFFER
P0.0 to P0.7
7
8
RESIDENT
OTP-ROM
8 kbytes
PORT 1
BUFFER
FILTER
PORT 2
FLIP-FLOP
PORT 0
BUFFER
PORT 1
FLIP-FLOP
PORT 0
FLIP-FLOP
DECODE
SINE WAVE
GENERATOR
INTERNAL
CLOCK
FREQ.
30
MEMORY
BANK
FLIP-FLOPS
32
4
HGF
REGISTER
LGF
REGISTER
MELODY
CONTROL
REGISTER
8
8
8
PCD3755x
8
8
8
8
8
8
8
TIMER 2
RELOAD
REGISTER
TIMER 2
REGISTER
EEPROM
CONTROL
REGISTER
EEPROM
ADDRESS
REGISTER
EEPROM
DATA
TRANSFER
INTERRUPT
LOGIC
ACCUMULATOR
8
8
8
TEMPORARY
REGISTER 2
TEMPORARY
REGISTER 1
8
HIGHER
PROGRAM
COUNTER
LOWER
PROGRAM
COUNTER
5
8
8
PROGRAM
STATUS
WORD
8
8
8
8
8
4
8
TIMER/
EVENT
COUNTER
T1
MULTIPLEXER
RAM
ADDRESS
REGISTER
timer interrupt
derivative
interrupt
ARITHMETIC
INSTRUCTION
REGISTER
AND
DECODER
POWER-ON-RESET
VPOR
T1
LOGIC UNIT
CE/T0
CONDITIONAL
external interrupt
DECIMAL
ADJUST
RESET
BRANCH
8 LEVEL STACK
(VARIABLE LENGTH)
OPTIONAL SECOND
REGISTER BANK
TIMER
FLAG
DATA STORE
CARRY
LOGIC
STOP
IDLE
ACC
CONTROL AND TIMING
CE/T0
RESET
XTAL1
XTAL2
ACC BIT
TEST
RESIDENT RAM ARRAY
128 bytes
MBG639
INITIALIZE
Fig.1 Block diagram.
OSCILLATOR
Product specification
handbook, full pagewidth
INTERRUPT
PCD3755A; PCD3755E;
PCD3755F
D
E
C
O
D
E
EEPROM
128 bytes
REGISTER 0
REGISTER 1
REGISTER 2
REGISTER 3
REGISTER 4
REGISTER 5
REGISTER 6
REGISTER 7
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
P1.7/MDY
BLOCK DIAGRAM
P1.0 to P1.6
TONE
4
Philips Semiconductors
4
1997 Apr 16
P2.0 to P2.3
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
5
5.1
PCD3755A; PCD3755E;
PCD3755F
PINNING INFORMATION
Pinning
handbook, halfpage
P0.1
1
28 P0.0
P0.2
2
27 P2.3
P0.3
3
26 P2.2
P0.4
4
25 P2.1
P0.5
5
24 VDD
P0.6
6
23 TONE
P0.7
7
22 V
9
20 P1.7/MDY
T1
XTAL1
SS
PCD3755xP
PCD3755xT
8
21 P2.0
XTAL2 10
19 P1.6
RESET 11
18 P1.5
CE/T0 12
17 P1.4
P1.0 13
16 P1.3
P1.1 14
15 P1.2
MBG640
25 P2.2
26 P2.3
27 P0.0
28 n.c.
29 P0.1
30 P0.2
handbook, full pagewidth
31 P0.3
32 P0.4
Fig.2 Pin configuration (SOT117-1 and SOT136-1).
n.c.
1
24 P2.1
P0.5
2
23 VDD
P0.6
3
22 TONE
P0.7
4
21 VSS
PCD3755xH
18 P1.6
RESET
8
17 n.c.
CE/T0
P1.5 16
7
P1.4 15
XTAL2
P1.3 14
19 P1.7/MDY
n.c. 13
6
P1.2 12
XTAL1
P1.1 11
20 P2.0
P1.0 10
5
9
T1
Fig.3 Pin configuration (SOT358-1).
1997 Apr 16
5
MBG641
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
5.2
PCD3755A; PCD3755E;
PCD3755F
Pin description
Table 1
SOT117-1 and SOT136-1 packages (for information on parallel I/O ports, see Chapter 14)
SYMBOL
PIN
TYPE
1 to 7
I/O
T1
8
I
Test 1 or count input of 8-bit Timer/event counter 1
XTAL1
9
I
crystal oscillator or external clock input
XTAL2
10
O
crystal oscillator output
RESET
11
I
reset input
CE/T0
12
I
Chip Enable or Test 0
13 to 19
I/O
7 bits of Port 1: 8-bit quasi-bidirectional I/O port
20
I/O
1 bit of Port 1: 8-bit quasi-bidirectional I/O port; or melody output
P2.0
21
I/O
VSS
22
P
ground
TONE
23
O
DTMF output
P1.1 to P0.7
P1.0 to P1.6
P1.7/MDY
VDD
P2.1 to P2.3
P0.0
Table 2
DESCRIPTION
7 bits of Port 0: 8-bit quasi-bidirectional I/O port
1 bit of Port 2: 4-bit quasi-bidirectional I/O port
24
P
25 to 27
I/O
3 bits of Port 2: 4-bit quasi-bidirectional I/O port
positive supply voltage
28
I/O
1 bit of Port 0: 8-bit quasi-bidirectional I/O port
SOT358-1 package (for information on parallel I/O ports, see Chapter 14)
SYMBOL
n.c.
P0.5 to P0.7
PIN
TYPE
1, 13, 17, 28
−
DESCRIPTION
not connected
2 to 4
I/O
T1
5
I
Test 1 or count input of 8-bit Timer/event counter 1
XTAL1
6
I
crystal oscillator or external clock input
XTAL2
7
O
crystal oscillator output
RESET
8
I
reset input
CE/T0
9
I
Chip Enable or Test 0
10 to 12,
14 to 16, 18
I/O
7 bits of Port 1: 8-bit quasi-bidirectional I/O port
P1.7/MDY
19
I/O
1 bit of Port 1: 8-bit quasi-bidirectional I/O port; or melody output
P2.0
20
I/O
1 bit of Port 2: 4-bit quasi-bidirectional I/O port
VSS
21
P
ground
TONE
22
O
DTMF output
VDD
23
P
positive supply voltage
P2.1 to P2.3
24 to 26
I/O
3 bits of Port 2: 4-bit quasi-bidirectional I/O port
P0.0 to P0.4
27, 29 to 32
I/O
5 bits of Port 0: 8-bit quasi-bidirectional I/O port
P1.0 to P1.6
1997 Apr 16
3 bits of Port 0: 8-bit quasi-bidirectional I/O port
6
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
6
PCD3755A; PCD3755E;
PCD3755F
The TONE output can alternatively issue twelve modem
frequencies for data rates between 300 and 1200 bits/s.
FREQUENCY GENERATOR
A versatile frequency generator section is provided (see
Fig.4). For normal operation, use a 3.58 MHz quartz
crystal or PXE resonator. The frequency generator
includes precision circuitry for dual tone multifrequency
(DTMF) signals, which is typically used for tone dialling
telephone sets.
In addition to DTMF and modem frequencies, two octaves
of musical scale in steps of semitones are available.
In case no tones are generated the TONE output is in
3-state mode.
Their frequencies are provided in purely sinusoidal form on
the TONE output or as square waves on the P1.7/MDY
output.
6.1
Frequency generator derivative registers
HIGH AND LOW GROUP FREQUENCY REGISTERS
6.1.1
Table 3 gives the addresses, mnemonics and access types of the High Group Frequency (HGF) and Low Group
Frequency (LGF) registers.
Table 3
Hexadecimal addresses, mnemonics, access types and bit mnemonics of the frequency registers
BIT MNEMONICS
REGISTER
ADDRESS
REGISTER
MNEMONIC
ACCESS
TYPE
7
6
5
4
3
2
1
0
11H
HGF
W
H7
H6
H5
H4
H3
H2
H1
H0
12H
LGF
W
L7
L6
L5
L4
L3
L2
L1
L0
6.1.2
MELODY CONTROL REGISTER (MDYCON)
MDYCON is a R/W register.
Table 4
Melody Control Register (address 13H)
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
EMO
Table 5
Description of MDYCON bits
BIT
MNEMONIC
7 to 1
−
0
EMO
1997 Apr 16
DESCRIPTION
These bits are set to a logic 0.
Enable Melody Output. If bit EMO = 0, then P1.7/MDY is a standard port line.
If bit EMO = 1, then P1.7/MDY is the melody output. EMO = 1 does not inhibit the port
instructions for P1.7/MDY. Therefore the state of both port line and flip-flop may be read
in and the port flip-flop may be written by port instructions. However, the port flip-flop of
P1.7/MDY must remain set to avoid conflicts between melody and port outputs.
When the HGF contents are zero while EMO = 1, P1.7/MDY is in the logic HIGH state.
7
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
handbook, full pagewidth
8
MELODY CONTROL
REGISTER
square wave
8
HGF REGISTER
PORT/MELODY
OUTPUT LOGIC
P1.7/
MDY
RC LOW-PASS
FILTER
TONE
DIGITAL
SINE WAVE
SYNTHESIZER
DAC
8 INTERNAL BUS
SWITCHED
CAPACITOR
BANDGAP
VOLTAGE
REFERENCE
SWITCHED
CAPACITOR
LOW-PASS
FILTER
MLC416
DAC
8
LGF REGISTER
DIGITAL
SINE WAVE
SYNTHESIZER
Fig.4 Block diagram of the frequency generator and melody output (P1.7/MDY) section.
1997 Apr 16
8
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
6.2
The amplitude of the Low group frequency sine wave is
attenuated by 2 dB compared to the amplitude of the High
group frequency sine wave. The two sine waves are
summed and then filtered by an on-chip switched
capacitor and RC low-pass filters. These guarantee that all
DTMF tones generated fulfil the CEPT recommendations
with respect to amplitude, frequency deviation, total
harmonic distortion and suppression of unwanted
frequency components.
Melody output (P1.7/MDY)
The melody output (P1.7/MDY) is very useful for
generating musical tones when a purely sinusoidal signal
is not required, such as for ringer applications.
The square wave (duty cycle = 12⁄23 or 52%) will include
the attenuated harmonics of the base frequency, which is
defined by the contents of the HGF register (Table 3).
However, even higher frequency tones may be produced
since the low-pass filtering on the TONE output is not
applied to the P1.7/MDY output. This results in the
minimum decimal value x in the HGF register being 2 for
the P1.7/MDY output, rather than 60 for the TONE output
- the value shown in equation (1). A sinusoidal TONE
output is produced at the same time as the melody square
wave, but due to the filtering, the higher frequency sine
waves with x < 60 will not appear at the TONE output.
The value 00H in a frequency register stops the
corresponding digital sine synthesizer. If both frequency
registers contain 00H, the whole frequency generator is
shut off, resulting in lower power consumption.
The frequency of the sine wave generated ‘f’ is dependent
on the clock frequency ‘fxtal’ and the decimal value ‘x’ held
in the frequency registers (HGF and LGF). The variables
are related by the equation:
f xtal
where
60 ≤ x ≤ 255
f = -------------------------------(1)
[ 23 ( x + 2 ) ]
Since the melody output is shared with P1.7, the port
flip-flop of P1.7 has to be set HIGH before using the
melody output. This is to avoid conflicts between melody
and port outputs. The melody output drive depends on the
configuration of port P1.7/MDY; see Chapter 14, Table 24.
6.3
The frequency limitation given by x ≥ 60 is due to the
low-pass filters which would attenuate higher frequency
sine waves.
Frequency registers
The two frequency registers HGF and LGF define two
frequencies. From these, the digital sine synthesizers
together with the Digital-to-Analog Converters (DACs)
construct two sine waves. Their amplitudes are precisely
scaled according to the bandgap voltage reference. This
ensures tone output levels independent of supply voltage
and temperature.
1997 Apr 16
PCD3755A; PCD3755E;
PCD3755F
9
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
6.4
DTMF frequencies
6.5
Assuming an oscillator frequency fxtal = 3.58 MHz, the
DTMF standard frequencies can be implemented as
shown in Table 6.
VALUE
(HEX)
STANDARD
HGF
VALUE
(HEX)
DEVIATION
GENERATED
(%)
(Hz)
DD
697
697.90
0.13
0.90
C8
770
770.46
0.06
0.46
B5
852
850.45
−0.18
−1.55
A3
941
943.23
0.24
2.23
7F
1209
1206.45
−0.21
−2.55
72
1336
1341.66
0.42
5.66
67
1477
1482.21
0.35
5.21
5D
1633
1638.24
0.32
5.24
Table 7
Table 8
DTMF standard frequencies and their
implementation; value = LGF, HGF contents
FREQUENCY (Hz)
Dialling symbols, corresponding DTMF
frequency pairs and frequency register contents
TELEPHONE DTMF FREQ.
KEYBOARD
PAIRS
SYMBOLS
(Hz)
LGF
VALUE
(HEX)
HGF
VALUE
(HEX)
Modem frequencies
Again assuming an oscillator frequency fxtal = 3.58 MHz,
the standard modem frequencies can be implemented as
in Table 8. It is suggested to define the frequency by the
HGF register while the LGF register contains 00H,
disabling Low Group Frequency generation.
The relationships between telephone keyboard symbols,
DTMF frequency pairs and the frequency register contents
are given in Table 7.
Table 6
PCD3755A; PCD3755E;
PCD3755F
Standard modem frequencies and their
implementation
FREQUENCY (Hz)
MODEM
978.82
−0.12
−1.18
82
1179.03
−0.08
−0.97
8F
1070(2)
1073.33
0.31
3.33
79
1270(2)
1265.30
−0.37
−4.70
80
1200(3)
1197.17
−0.24
−2.83
45
2200(3)
2192.01
−0.36
−7.99
76
1300(4)
1296.94
−0.24
−3.06
48
2100(4)
2103.14
0.15
3.14
5C
1650(1)
1655.66
0.34
5.66
52
1850(1)
1852.77
0.15
2.77
4B
2025(2)
2021.20
−0.19
−3.80
44
2225(2)
2223.32
−0.08
−1.68
Notes
1. Standard is V.21.
72
2. Standard is Bell 103.
1
(697, 1209)
DD
7F
3. Standard is Bell 202.
2
(697, 1336)
DD
72
4. Standard is V.23.
3
(697, 1477)
DD
67
4
(770, 1209)
C8
7F
5
(770, 1336)
C8
72
6
(770, 1477)
C8
67
7
(852, 1209)
B5
7F
8
(852, 1336)
B5
72
9
(852, 1477)
B5
67
A
(697, 1633)
DD
5D
C8
5D
(852, 1633)
B5
5D
D
(941, 1633)
A3
5D
•
(941, 1209)
A3
7F
#
(941, 1477)
A3
67
1997 Apr 16
10
(Hz)
1180(1)
A3
(770, 1633)
(%)
980(1)
(941, 1336)
B
GENERATED
9D
0
C
DEVIATION
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
6.6
Musical scale frequencies
7
Finally, two octaves of musical scale in steps of semitones
can be realized, again assuming an oscillator frequency
fxtal = 3.58 MHz (Table 9). It is suggested to define the
frequency by the HGF register while the LGF contains
00H, disabling Low Group Frequency generation.
Table 9
NOTE
FREQUENCY (Hz)
STANDARD(1)
GENERATED
D#5
F8
622.3
622.5
E5
EA
659.3
659.5
F5
DD
698.5
697.9
F#5
D0
740.0
741.1
G5
C5
784.0
782.1
G#5
B9
830.6
832.3
A5
AF
880.0
879.3
A#5
A5
923.3
931.9
B5
9C
987.8
985.0
C6
93
1046.5
1044.5
C#6
8A
1108.7
1111.7
D6
82
1174.7
1179.0
D#6
7B
1244.5
1245.1
E6
74
1318.5
1318.9
F6
6D
1396.9
1402.1
F#6
67
1480.0
1482.2
G6
61
1568.0
1572.0
G#6
5C
1661.2
1655.7
A6
56
1760.0
1768.5
A#6
51
1864.7
1875.1
B6
4D
1975.5
1970.0
C7
48
2093.0
2103.3
C#7
44
2217.5
2223.3
D7
40
2349.3
2358.1
D#7
3D
2489.0
2470.4
The most significant difference between a RAM and an
EEPROM is that a bit in EEPROM, once written to a
logic 1, cannot be cleared by a subsequent write
operation. Successive write accesses actually perform a
logical OR with the previously stored information.
Therefore, to clear a bit, the whole byte must be erased
and re-written with the particular bit cleared. Thus, an
erase-and-write operation is the EEPROM equivalent of a
RAM write operation.
Whereas read access times to an EEPROM are
comparable to RAM access times, write and erase
accesses are much slower at 5 ms each. To make these
operations more efficient, several provisions are available
in the PCD3755A, PCD3755E and PCD3755F.
First, the EEPROM array is structured into 32 four-byte
pages (see Fig.5) permitting access to 4 bytes in parallel
(write page, erase/write page and erase page). It is also
possible to erase and write individual bytes. Finally, the
EEPROM address register provides auto-incrementing,
allowing very efficient read and write accesses to
sequential bytes.
To simplify the erase and write timing, the derivative 8-bit
down-counter (Timer 2) with reload register is provided.
In addition to EEPROM timing, Timer 2 can be used for
general real-time tasks, such as for measuring signal
duration and for defining pulse widths.
Note
1. Standard scale based on A4 @ 440 Hz.
1997 Apr 16
EEPROM AND TIMER 2 ORGANIZATION
The PCD3755A, PCD3755E and PCD3755F have
128 bytes of Electrically Erasable Programmable
Read-Only Memory (EEPROM). Such non-volatile storage
provides data retention without the need for battery
backup. In telecom applications, the EEPROM is used for
storing redial numbers and for short dialling of frequently
used numbers. More generally, EEPROM may be used for
customizing microcontrollers, such as to include a PIN
code or a country code, to define trimming parameters, to
select application features from the range stored in ROM.
Musical scale frequencies and their
implementation
HGF
VALUE
(HEX)
PCD3755A; PCD3755E;
PCD3755F
11
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
handbook, full pagewidth
PCD3755A; PCD3755E;
PCD3755F
5
8
EEPROM ADDRESS REGISTER
2
2 : 4 DECODER
8
5 : 32 DECODER
EEPROM LATCH 0
F0
EEPROM LATCH 1
F1
128-byte EEPROM ARRAY
(32 4-byte PAGES)
EEPROM LATCH 2
F2
EEPROM LATCH 3
F3
8
8
EEPROM TEST REGISTER
8
EEPROM CONTROL REGISTER
8
T2F set on
underflow
TIMER 2 RELOAD REGISTER
8
8
TIMER 2 REGISTER (T2)
8
INTERNAL
BUS
MGB824
1
f
480 xtal
Fig.5 Block diagram of the EEPROM and Timer 2.
1997 Apr 16
12
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
7.1
PCD3755A; PCD3755E;
PCD3755F
EEPROM registers
7.1.1
EEPROM CONTROL REGISTER (EPCR)
The behaviour of the EEPROM and Timer 2 section is defined by the EEPROM Control Register.
Table 10 EEPROM Control Register (address 04H, access type R/W)
7
6
5
4
3
2
1
0
STT2
ET2I
T2F
EWP
MC3
MC2
MC1
0
Table 11 Description of EPCR bits
BIT
MNEMONIC
DESCRIPTION
7
STT2
Start T2. If STT2 = 0, then Timer 2 is stopped; T2 value held. If STT2 = 1, then T2
decrements from reload value.
6
ET2I
Enable T2 interrupt. If ET2I = 0, then T2F event cannot request interrupt. If ET2I = 1,
then T2F event can request interrupt.
5
T2F
Timer 2 flag. Set when T2 underflows (or by program); reset by program.
4
EWP
Erase or write in progress (EWP). Set by program (EWP starts EEPROM erase and/or
write and Timer 2). Reset at the end of EEPROM erase and/or write.
3
MC3
2
MC2
Mode control 3 to 1. These three bits in conjunction with bit EWP select the mode as
shown in Table 12.
1
MC1
0
−
This bit is set to a logic 0.
Table 12 Mode selection; X = don’t care
EWP
MC3
MC2
MC1
0
0
0
0
read byte
0
0
1
0
increment mode
1
0
1
X
write page
1
1
0
0
erase/write page
1
1
1
1
erase page
X
0
0
1
not allowed
X
1
0
1
X
1
1
0
1997 Apr 16
DESCRIPTION
13
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
7.1.2
PCD3755A; PCD3755E;
PCD3755F
EEPROM ADDRESS REGISTER (ADDR)
The EEPROM Address Register determines the EEPROM location to which an EEPROM access is directed.
As a whole, ADDR auto-increments after read and write cycles to EEPROM, but remains fixed after erase cycles. This
behaviour generates the correct ADDR contents for sequential read accesses and for sequential write or erase/write
accesses with intermediate page setup. Overflow of the 8-bit counter wraps around to zero.
Table 13 EEPROM Address Register (address 01H, access type R/W)
7
6
5
4
3
2
1
0
0
AD6
AD5
AD4
AD3
AD2
AD1
AD0
Table 14 Description of ADDR bits
BIT
MNEMONIC
7
−
6 to 2
AD6 to AD2
AD2 to AD6 select one of 32 pages.
1 to 0
AD1 to AD0
AD1 and AD0 are irrelevant during erase and write cycles. For read accesses, AD0 and
AD1 indicate the byte location within an EEPROM page. During page setup, finally, AD0
and AD1 select EEPROM Latch 0 to 3 whereas AD2 to AD6 are irrelevant. If increment
mode (Table 12) is active during page setup, the subcounter consisting of AD0 and AD1
increments after every write to an EEPROM latch, thus enhancing access to sequential
EEPROM latches. Incrementing stops when EEPROM Latch 3 is reached, i.e. when
AD0 and AD1 are both a logic 1.
7.1.3
DESCRIPTION
This bit is set to a logic 0.
EEPROM DATA REGISTER (DATR)
Table 15 EEPROM Data Register (address 03H; access type R/W)
7
6
5
4
3
2
1
0
D7
D6
D5
D4
D3
D2
D1
D0
Table 16 Description of DATR bits
BIT
MNEMONIC
DESCRIPTION
7 to 0
D7 to D0
The EEPROM Data Register (DATR) is only a conceptual entity. A read operation from
DATR, reads out the EEPROM byte addressed by ADDR. On the other hand, a write
operation to DATR, loads data into the EEPROM latch (see Fig.5) defined by bits AD0
and AD1 of ADDR.
7.1.4
EEPROM TEST REGISTER (TST)
The EEPROM Test register is used for testing purposes during device manufacture. It must not be accessed by the
device user.
1997 Apr 16
14
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
7.2
page, are irrelevant during write and erase cycles.
However, write and erase cycles need not affect all bytes
of the page. The EEPROM flags F0 to F3 (see Fig.5)
determine which bytes within the EEPROM page are
affected by the erase and/or write cycles. A byte whose
corresponding EEPROM flag is zero remains unchanged.
EEPROM latches
The four EEPROM latches (EEPROM Latch 0 to 3; Fig.5)
cannot be read by user software. Due to their construction,
the latches can only be preset, but not cleared. Successive
write operations through DATR to the EEPROM latches
actually perform a logical OR with the previously stored
data in EEPROM. The EEPROM latches are reset at the
conclusion of any EEPROM cycle.
7.3
PCD3755A; PCD3755E;
PCD3755F
With erase page, a byte is erased if its corresponding
EEPROM flag is set. With write page, data in EEPROM
Latch 0 to 3 (Fig.5) are ORed to the individual page bytes
if and only if the corresponding EEPROM flags are set.
EEPROM flags
The four EEPROM flags (F0 to F3; Fig.5) cannot be
directly accessed by user software. An EEPROM flag is
set as a side-effect when the corresponding EEPROM
latch is written through DATR. The EEPROM flags are
reset at the conclusion of any EEPROM cycle.
In an erase/write cycle, F0 to F3 select which page bytes
are erased and ORed with the corresponding EEPROM
latches.
7.4
The described page-wise organization of erase and write
cycles allows up to four bytes to be individually erased or
written within 5 ms. This advantage necessitates a
preparation step, called page setup, before the actual
erase and/or write cycle can be executed.
ORing, in this event, means that the EEPROM latches are
copied to the selected page bytes.
EEPROM macros
The instruction sequence used in an EEPROM access
should be treated as an indivisible entity. Erroneous
programs result if ADDR, DATR, RELR or EPCR are
inadvertently changed during an EEPROM cycle or its
setup. Special care should be taken if the program may
asynchronously divert due to an interrupt. Particularly,
a new access to the EEPROM may only be initiated when
no write, erase or erase/write cycles are in progress.
This can be verified by reading bit EWP (register EPCR).
Page setup controls EEPROM latches and EEPROM
flags. This will be described in the Sections 7.5.1 to 7.5.5.
7.5.1
Page setup is a preparation step required before write
page, erase page and erase/write page cycles.
As previously described, these page operations include
single-byte write, erase and erase/write as a special event.
EEPROM flags F0 to F3 determine which page bytes will
be affected by the mentioned page operations. EEPROM
Latch 0 to 3 must be preset through DATR to specify the
write cycle data to EEPROM and to set the EEPROM flags
as a side-effect. Obviously, the actual preset value of the
EEPROM latches is irrelevant for erase page. Preset of
one, two, three or all four EEPROM latches and the
corresponding EEPROM flags can be performed by
repeatedly defining ADDR and writing to DATR (see
Table 17).
For write, erase and erase/write cycles, it is assumed that
the Timer 2 Reload Register (RELR) has been loaded with
the appropriate value for a 5 ms delay, which depends on
fxtal (see Table 23). The end of a write, erase or erase/write
cycle will be signalled by a cleared EWP and by a Timer 2
interrupt provided that ET2I = 1 and that the derivative
interrupt is enabled.
7.5
EEPROM access
One read, one write, one erase/write and one erase
access are defined by bits EWP and MC1 to MC3 in the
EPCR register; see Table 10.
Read byte retrieves the EEPROM byte addressed by
ADDR when DATR is read. Read cycles are
instantaneous.
If more than one EEPROM latch must be preset, the
subcounter consisting of AD0 and AD1 can be induced to
auto-increment after every write to DATR, thus stepping
through all EEPROM latches. For this purpose, increment
mode (Table 12) must be selected. Auto-incrementing
stops at EEPROM Latch 3. It is not mandatory to start at
EEPROM Latch 0 as in shown in Table 18.
Write and erase cycles take 5 ms, however. Erase/write is
a combination of an erase and a subsequent write cycle,
consequently taking 10 ms.
As their names imply, write page, erase page and
erase/write page are applied to a whole EEPROM page.
Therefore, bits AD0 and AD1 of register ADDR (see
Table 13), defining the byte location within an EEPROM
1997 Apr 16
PAGE SETUP
Note that AD2 to AD6 are irrelevant during page setup.
They will usually specify the intended EEPROM page,
anticipating the subsequent page cycle.
15
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
From now on, it will be assumed that AD2 to AD6 will
contain the intended EEPROM page address after page
setup.
To actually copy the data from the EEPROM latches,
the corresponding bytes in the page should previously
have been erased.
The EEPROM latches are preset as described in
Section 7.5.1. The actual transfer to the EEPROM is then
performed as shown in Table 20.
Table 17 Page setup; preset
INSTRUCTION
RESULT
MOV A, #addr
address of EEPROM latch
MOV ADDR, A
send address to ADDR
MOV A, #data
load write, erase/write or erase data
MOV DATR, A
send data to addressed EEPROM
latch
The last instruction also starts Timer 2. The data in the
EEPROM latches are ORed with that in the corresponding
page bytes within 5 ms. A single-byte write is simply a
special case of ‘write page’.
ADDR auto-increments after the write cycle. If AD0 and
AD1 addressed EEPROM Latch 3 prior to the write cycle,
ADDR will point to the next EEPROM page (by bits AD2
to AD6) and to EEPROM Latch 0 (by bits AD0 and AD1).
This allows efficient coding of multi-page write operations.
Table 18 Page setup; auto-incrementing
INSTRUCTION
RESULT
MOV A, #MC2
increment mode control word
MOV EPCR, A
select increment mode
MOV A, #baddr
EEPROM Latch 0 address
(AD0 = AD1 = 0)
MOV ADDR, A
send EEPROM Latch 0 address to
ADDR
MOV A, R0
load 1st byte from Register 0
1st
MOV DATR, A
send
MOV A, R1
load 2nd byte from Register 1
MOV DATR, A
send 2nd byte to EEPROM Latch 1
MOV A, R2
load 3rd byte from Register 2
MOV DATR, A
send 3rd byte to EEPROM Latch 2
MOV A, R3
MOV DATR, A
7.5.2
Table 20 Write page
INSTRUCTION
load
byte from Register 3
send
4th
byte to EEPROM Latch 3
‘write page’ control word
MOV EPCR, A
start ‘write page’ cycle
ERASE/WRITE PAGE
The EEPROM latches are preset as described in
Section 7.5.1. The page byte corresponding to the
asserted flags (among F0 to F3) are erased and re-written
with the contents of the respective EEPROM latches.
The last instruction also starts Timer 2. Erasure takes
5 ms upon which Timer Register T2 reloads for another
5 ms cycle for writing. The top cycles together take 10 ms.
A single-byte erase/write is simply a special event of
‘erase/write page’.
READ BYTE
ADDR auto-increments after the write cycle. If AD0 and
AD1 addressed EEPROM Latch 3 prior to the write cycle,
ADDR will point to the next EEPROM page (by AD2 to
AD6) and to EEPROM Latch 0 (by AD0 and AD1).
This allows efficient coding of multi-page erase/write
operations.
Since ADDR auto-increments after a read cycle regardless
of the page boundary, successive bytes can efficiently be
read by repeating the last instruction.
Table 19 Read byte
INSTRUCTION
RESULT
MOV A, #EWP + MC2
7.5.4
byte to EEPROM Latch 0
4th
PCD3755A; PCD3755E;
PCD3755F
RESULT
Table 21 Erase/write page
MOV A, #RDADDR load read address
MOV ADDR, A
send address to ADDR
MOV A, DATR
read EEPROM data
7.5.3
INSTRUCTION
WRITE PAGE
The write cycle performs a logical OR between the data in
the EEPROM latches and that in the addressed EEPROM
page.
1997 Apr 16
16
RESULT
MOV A, #EWP + MC3
‘erase/write page’ control word
MOV EPCR, A
start ‘erase/write page’ cycle
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
7.5.5
The second underflow of an erase/write cycle and the first
underflow of write page and erase page conclude the
corresponding EEPROM cycle. Timer 2 is stopped, T2F is
set whereas EWP and MC1 to MC3 are cleared.
ERASE PAGE
The EEPROM flags are set as described in Section 7.5.1.
The corresponding page bytes are erased.
The last instruction also starts Timer 2. Erasure takes
5 ms. A single-byte erase is simply a special case of ‘erase
page’.
Table 23 Reload values as a function of fxtal
Note that ADDR does not auto-increment after an erase
cycle.
fxtal
(MHz)
RELOAD VALUE(1)
(HEX)
1
0A
2
14
Table 22 Erase page
INSTRUCTION
RESULT
3.58
25
6
3E
10
68
16
A6
MOV A, #EWP + MC3 + MC2 + MC1 ‘erase page’
control word
MOV EPCR, A
7.6
start ‘erase
page’ cycle
Note
1. The reload value is (5 × 10−3 × 1⁄480 × fxtal) − 1;
fxtal in MHz.
Timer 2
Timer 2 is a 8-bit down-counter decremented at a rate of
1⁄
480 × fxtal. It may be used either for EEPROM timing or as
a general purpose timer. Conflicts between the two
applications should be carefully avoided.
7.6.1
7.6.2
TIMER 2 AS A GENERAL PURPOSE TIMER
When used for purposes other than EEPROM timing,
Timer 2 is started by setting STT2. The Timer Register T2
(see Table 26) is loaded with the reload value from RELR.
T2 decrements to zero. On underflow, T2 is reloaded from
RELR, T2F is set and T2 continues to decrement.
TIMER 2 FOR EEPROM TIMING
When used for EEPROM timing, Timer 2 serves to
generate the 5 ms intervals needed for erasing or writing
the EEPROM. At the decrement rate of 1⁄480 × fxtal, the
reload value for a 5 ms interval is a function of fxtal.
Table 23 summarizes the required reload values for a
number of oscillator frequencies.
Timer 2 can be stopped at any time by clearing STT2.
The value of T2 is then held and can be read out. After
setting STT2 again, Timer 2 decrements from the reload
value. Alternatively, it is possible to read T2 ‘on the fly’ i.e.
while Timer 2 is operating.
Timer 2 is started by setting bit EWP in the EPCR.
The Timer Register T2 is loaded with the reload value from
RELR. T2 decrements to zero.
For an erase/write cycle, underflow of T2 indicates the end
of the erase operation. Therefore, Timer Register T2 is
reloaded from RELR for another 5 ms interval during
which the flagged EEPROM latches are copied to the
corresponding bytes in the page addressed by ADDR.
1997 Apr 16
PCD3755A; PCD3755E;
PCD3755F
17
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
8
PCD3755A; PCD3755E;
PCD3755F
11 IDLE MODE
DERIVATIVE INTERRUPTS
In Idle mode, the frequency generator, the EEPROM and
the Timer 2 sections remain operative. Therefore, the
IDLE instruction may be executed while an erase and/or
write access to EEPROM is in progress.
One derivative interrupt event is defined. It is controlled by
bits T2F and ET2I in the EPCR (see Tables 10 and 11).
The derivative interrupt event occurs when T2F is set. This
request is honoured under the following circumstances:
• No interrupt routine proceeds
• No external interrupt request is pending
12 STOP MODE
• The derivative interrupt is enabled
Since the oscillator is switched off, the frequency
generator, the EEPROM and the Timer 2 sections receive
no clock. It is suggested to clear both the HGF and the
LGF registers before entering Stop mode. This will cut off
the biasing of the internal amplifiers, considerably
reducing current requirements.
• ET2I is set.
The derivative interrupt routine must include instructions
that will remove the cause of the derivative interrupt by
explicitly clearing T2F. If the derivative interrupt is not
used, T2F may directly be tested by the program.
Obviously, T2F can also be asserted under program
control, e.g. to generate a software interrupt.
9
The Stop mode must not be entered while an erase
and/or write access to EEPROM is in progress. The STOP
instruction may only be executed when EWP in EPCR is
zero. The Timer 2 section is frozen during Stop mode.
After exit from Stop mode by a HIGH level on CE/T0,
Timer 2 proceeds from the held state.
TIMING
Although thePCD3755A, PCD3755E and PCD3755F
operate over a clock frequency range from 1 to 16 MHz,
fxtal = 3.58 MHz will usually be chosen to take full
advantage of the frequency generator section.
13 INSTRUCTION SET RESTRICTIONS
As RAM space is restricted to 128 bytes, care should be
taken to avoid accesses to non-existing RAM locations.
10 RESET
In addition to the conditions given in the “PCD33xxA
Family” data sheet, all derivative registers are cleared in
the reset state.
14 OVERVIEW OF PORT AND POWER-ON-RESET CONFIGURATION
Table 24 Port and Power-on-reset configuration
See note 1 and 2.
PORT 0
PORT 1
PORT 2
TYPE
0
2
3
4
5
6
7
0
1
2
3
4
5
6
1
2
3
PCD3755A 1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1R 1R(3) 2S
2S
2S
2S
1.3 V
PCD3755E 1S 1S 1S 1S 1S 1S 1S 1S 2S 2S 2S 2S 2S 2S 1S 1S(3) 2S
1R
1R
1R
2.0 V
2S
2S
2S
2.0 V
1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1S 1R
7
VPOR
0
PCD3755F
1
1R(3)
2S
Notes
1. Port output drive: 1 = standard I/O; 2 = open-drain I/O, see “PCD33xxA Family” data sheet.
2. Port state after reset: S = Set (HIGH) and R = Reset (LOW).
3. The Melody Output drive type is push-pull.
1997 Apr 16
18
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
Thus, the complete OTP memory cannot be tested by the
factory, but only partially via a special test array.
The average expected yield is 97%.
15 OTP PROGRAMMING
The programming of the PCD3755x and PCD3756x OTPs
is based on the OM4260 programmer (Ceibo MP-51),
available from Philips. The OM4260 works in conjunction
with various adapters supporting the different package
types available as listed in Table 25.
Detailed information on the OTP programming is available
in the “PCD3755x Application Note”, which is available via
your Philips Sales office.
The low-voltage OTP program memory used is of
Anti-Fuse-PROM type and can not be erased after
programming.
Table 25 OTP programming overview
DEVICE
PHILIPS TYPE NUMBER
CEIBO TYPE NUMBER
SUPPORTED PACKAGE
Ceibo MP-51
OM4260
MP-51 programmer base
−
PCD3755x/56x
OM5007
PCD3755A / 56A adapter DIP
DIP28
PCD3755x/56x
OM5030
PCD3755A / 56A adapter SO
SO28
PCD3755x/56x
OM5037(1)
PCD3755A / 56A adapter QFP32 LQFP32
Note
1. As the OM5037 is only a socket converter, the OM5007 is also needed to program the PCD3755x/56x in the LQFP32
package.
1997 Apr 16
19
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
16 SUMMARY OF DERIVATIVE REGISTERS
Table 26 Register map
ADDR.
(HEX)
REGISTER
00
not used
01
EEPROM Address Register
(ADDR)
02
not used
03
EEPROM Data Register
(DATR)
04
EEPROM Control Register
(EPCR)
05
Timer 2 Reload Register
(RELR)
06
Timer 2 Register
(T2)
07
Test Register
(TST)
7
6
5
4
3
2
1
0
R/W
0
AD6
AD5
AD4
AD3
AD2
AD1
AD0
R/W
D7
D6
D5
D4
D3
D2
D1
D0
R/W
STT2
ET21
TF2
EWP
MC3
MC2
MC1
0
R/W
R7
R6
R5
R4
R3
R2
R1
R0
R/W
T2.7
T2.6
T2.5
T2.4
T2.3
T2.2
T2.1
T2.0
R
only for test purposes; not to be accessed by the device user
08 to 10 not used
11
High Group Frequency Register
(HGF)
H7
H6
H5
H4
H3
H2
H1
H0
W
12
Low Group Frequency Register
(LGF)
L7
L6
L5
L4
L3
L2
L1
L0
W
13
Melody Control Register
(MDYCON)
0
0
0
0
0
0
0
EMO
R/W
14 to FF not used
17 HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, it is good practice to take
normal precautions appropriate to handling MOS devices (see “Data Handbook IC14, Section: Handling MOS devices”).
18 LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
MIN.
MAX.
UNIT
VDD
supply voltage
−0.8
+7.0
V
VI
all input voltages
−0.5
VDD + 0.5
V
II
DC input current
−10
+10
mA
IO
DC output current
−10
+10
mA
Ptot
total power dissipation
−
125
mW
PO
power dissipation per output
−
30
mW
ISS
ground supply current
−50
+50
mA
Tstg
storage temperature
−65
+150
°C
Tj
operating junction temperature
−
90
°C
1997 Apr 16
20
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
19 DC CHARACTERISTICS
VDD = 1.8 to 6 V; VSS = 0 V; Tamb = −25 to +70 °C; all voltages with respect to VSS; fxtal = 3.58 MHz; unless otherwise
specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supply
VDD
supply voltage
operating
see Fig.6
note 1
RAM data retention in Stop
mode
IDD
operating supply current
1.8
−
6
V
1.0
−
6
V
0.8
1.6
mA
see Figs 7 and 8; note 2
VDD = 3 V; value HGF or LGF ≠ 0 −
IDD(idle)
IDD(stp)
supply current (Idle mode)
supply current (Stop mode)
VDD = 3 V
−
0.35
0.7
mA
VDD = 5 V; fxtal = 10 MHz
−
1.5
4.0
mA
VDD = 5 V; fxtal = 16 MHz
−
2.4
6.0
mA
VDD = 3 V; value HGF or LGF ≠ 0 −
0.7
1.4
mA
see Figs 9 and 10; note 2
VDD = 3 V
−
0.25
0.5
mA
VDD = 5 V; fxtal = 10 MHz
−
1.1
3.4
mA
VDD = 5 V; fxtal = 16 MHz
−
1.7
5.0
mA
VDD = 1.8 V; Tamb = 25 °C
−
1.0
5.5
µA
VDD = 1.8 V; Tamb = 70 °C
−
−
10
µA
−
see Fig.11; note 3
Inputs
VIL
LOW level input voltage
0
VIH
HIGH level input voltage
0.7VDD −
VDD
0.3VDD V
V
ILI
input leakage current
VSS ≤ VI ≤ VDD
−1
−
+1
µA
Port outputs
IOL
LOW level port sink current
VDD = 3 V; VO = 0.4 V; see Fig.12
0.7
3.5
−
mA
IOH
HIGH level pull-up output source VDD = 3 V; VO = 2.7 V; see Fig.13
current
VDD = 3 V; VO = 0 V; see Fig.13
−10
−30
−
µA
−
−140
−300
µA
IOH1
HIGH level push-pull output
source current
−0.7
−3.5
−
mA
VDD = 3 V; VO = 2.6 V; see Fig.14
Tone output (see Fig.15; note 4)
VHG(RMS)
HGF voltage (RMS)
158
181
205
mV
VLG(RMS)
LGF voltage (RMS)
125
142
160
mV
∆f ⁄ f
frequency deviation
−0.6
−
+0.6
%
VDC
DC voltage level
−
0.5VDD −
V
Zo
output impedance
−
100
500
Ω
Gv
pre-emphasis of group
1.5
2.0
2.5
dB
THD
total harmonic distortion
−
25
−
dB
1997 Apr 16
Tamb = 25 °C; note 5
21
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
SYMBOL
PARAMETER
PCD3755A; PCD3755E;
PCD3755F
CONDITIONS
MIN.
TYP.
MAX.
UNIT
EEPROM (notes 1 and 6)
105
−
−
10
−
−
years
PCD3755A
0.8
1.3
1.8
V
PCD3755E
1.5
2.0
2.5
V
PCD3755F
1.5
2.0
2.5
V
0.2
0.4
1.0
mS
0.3
1.0
3.0
MΩ
CYt/w
endurance (erase/write cycles)
tret
data retention time
note 7
Power-on-reset (see Fig.16)
VPOR
Power-on-reset level
Oscillator (see Fig.17)
gm
transconductance
RF
feedback resistor
VDD = 5 V
Notes
1. TONE output, EEPROM erase and write require VDD ≥ 2.5 V.
2. VIL = VSS; VIH = VDD; open-drain outputs connected to VSS; all other outputs open; value HGF = LGF = 0, unless
otherwise specified.
a) Maximum values: external clock at XTAL1 and XTAL2 open-circuit.
b) Typical values: Tamb = 25 °C; crystal connected between XTAL1 and XTAL2.
3. VIL = VSS; VIH = VDD; RESET, T1 and CE/T0 at VSS; crystal connected between XTAL1 and XTAL2; pins T1 and
CE/T0 at VSS.
4. Values are specified for DTMF frequencies only (CEPT).
5. Related to the Low Group Frequency (LGF) component (CEPT).
6. After final testing the value of each EEPROM bit is a logic 1, but this cannot be guaranteed after board assembly.
7. Verified on sampling basis.
1997 Apr 16
22
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
MLA493
18
PCD3755A; PCD3755E;
PCD3755F
MGB827
6
handbook,
halfpage
f
handbook, halfpage
xtal
(MHz)
15
IDD
(mA)
16 MHz
4
12
9
3.58 MHz
HGF or LGF ≠ 0
guaranteed
operating range
6
10 MHz
2
3.58 MHz
3
0
0
1
1
3
5
3
5
7
VDD (V)
VDD (V)
7
Measured with crystal between XTAL1 and XTAL2.
Fig.6
Maximum clock frequency (fxtal) as a
function of supply voltage (VDD).
Fig.7
MGB828
6
Typical operating supply current (IDD) as a
function of supply voltage (VDD).
MGB829
6
handbook, halfpage
handbook, halfpage
IDD
(mA)
IDD(idle)
(mA)
4
4
16 MHz
5V
3.58 MHz
HGF or LGF ≠ 0
2
2
10 MHz
3V
3.58 MHz
0
1
10
fxtal (MHz)
10
0
2
1
3
5
VDD (V)
Measured with function generator on XTAL1.
Measured with crystal between XTAL1 and XTAL2.
Fig.8
Fig.9
Typical operating supply current (IDD) as a
function of clock frequency (fxtal).
1997 Apr 16
23
7
Typical supply current in Idle mode (IDD(idle))
as a function of supply voltage (VDD).
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
MGB826
MGB830
6
6
handbook, halfpage
handbook, halfpage
IDD(idle)
(mA)
IDD(stp)
(µA)
5
4
4
3
2
2
5V
1
3V
0
1
10
fxtal (MHz)
10
0
2
1
3
5
VDD (V)
7
Measured with function generator on XTAL1.
Fig.11 Typical supply current in Stop mode
(IDD(stp)) as a function of supply voltage
(VDD).
Fig.10 Typical supply current in Idle mode (IDD(idle))
as a function of clock frequency (fxtal).
MGB831
MGB832
−300
12
handbook, halfpage
handbook, halfpage
IOL
(mA)
IOH
(µA)
8
−200
4
−100
VO = 0 V
VO = 0.9VDD
0
0
1
3
5
VDD (V)
7
1
3
5
VDD (V)
7
VO = 0.4 V.
Fig.13 Typical HIGH level pull-up output source
current (IOH) as a function of supply voltage
(VDD).
Fig.12 Typical LOW level output sink current (IOL)
as a function of supply voltage (VDD).
1997 Apr 16
24
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
MGB833
−12
handbook, halfpage
IOH1
(mA)
handbook, halfpage VDD
−8
DEVICE TYPE NUMBER
(1)
TONE
1 µF
10 kΩ
50 pF
−4
VSS
MGB835
0
1
3
5
VDD (V)
7
VO = VDD − 0.4 V.
(1) Device type number: PCD3755A, PCD3755E or PCD3755F.
Fig.14 Typical HIGH level push-pull output source
current (IOH1) as a function of supply voltage
(VDD).
Fig.15 TONE output test circuit.
MGD495
6
MGB834
10
handbook, halfpage
handbook, halfpage
VDD
(V)
gm
(mS)
4
1
VPOR = 2.0 V
2
VPOR = 1.3 V
0
−25
10
25
75
125
Tamb (°C)
70
Fig.16 Typical Power-on-reset level (VPOR) as
function of ambient temperature (Tamb).
1997 Apr 16
1
1
3
5
VDD (V)
7
Fig.17 Typical transconductance (gm) as a function
of supply voltage (VDD).
25
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
20 AC CHARACTERISTICS
VDD = 1.8 to 6 V; VSS = 0 V; Tamb = −25 to +70 °C; all voltages with respect to VSS; unless otherwise specified.
SYMBOL
PARAMETER
tr
rise time all outputs
tf
fall time all outputs
fxtal
clock frequency
1997 Apr 16
CONDITIONS
VDD = 5 V; Tamb = 25 °C; CL = 50 pF
see Fig.6
26
MIN.
TYP.
MAX.
UNIT
−
30
−
ns
−
30
−
ns
1
−
16
MHz
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
21 PACKAGE OUTLINES
seating plane
handbook, full
pagewidthdual in-line package; 28 leads (600 mil)
DIP28:
plastic
SOT117-1
ME
D
A2
L
A
A1
c
e
Z
w M
b1
(e 1)
b
MH
15
28
pin 1 index
E
1
14
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
min.
A2
max.
b
b1
c
D (1)
E (1)
e
e1
L
ME
MH
w
Z (1)
max.
mm
5.1
0.51
4.0
1.7
1.3
0.53
0.38
0.32
0.23
36.0
35.0
14.1
13.7
2.54
15.24
3.9
3.4
15.80
15.24
17.15
15.90
0.25
1.7
inches
0.20
0.020
0.16
0.066
0.051
0.020
0.014
0.013
0.009
1.41
1.34
0.56
0.54
0.10
0.60
0.15
0.13
0.62
0.60
0.68
0.63
0.01
0.067
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT117-1
051G05
MO-015AH
1997 Apr 16
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
92-11-17
95-01-14
27
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
SO28: plastic small outline package; 28 leads; body width 7.5 mm
SOT136-1
D
E
A
X
c
y
HE
v M A
Z
15
28
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
1
14
e
bp
0
detail X
w M
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
mm
2.65
0.30
0.10
2.45
2.25
0.25
0.49
0.36
0.32
0.23
18.1
17.7
7.6
7.4
1.27
10.65
10.00
1.4
1.1
0.4
1.1
1.0
0.25
0.25
0.1
0.9
0.4
0.012 0.096
0.004 0.089
0.01
0.019 0.013
0.014 0.009
0.71
0.69
0.30
0.29
0.050
0.419
0.043
0.055
0.394
0.016
0.043
0.039
0.01
0.01
0.004
0.035
0.016
inches
0.10
Z
(1)
θ
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT136-1
075E06
MS-013AE
1997 Apr 16
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
95-01-24
97-05-22
28
o
8
0o
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
LQFP32: plastic low profile quad flat package; 32 leads; body 7 x 7 x 1.4 mm
SOT358-1
c
y
X
24
A
17
25
16
ZE
e
E HE
A A2 A
1
(A 3)
wM
θ
bp
Lp
L
pin 1 index
32
9
detail X
8
1
e
ZD
v M A
wM
bp
D
B
HD
v M B
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HD
HE
L
Lp
v
w
y
mm
1.60
0.20
0.05
1.45
1.35
0.25
0.4
0.3
0.18
0.12
7.1
6.9
7.1
6.9
0.8
9.15
8.85
9.15
8.85
1.0
0.75
0.45
0.2
0.25
0.1
Z D (1) Z E (1)
0.9
0.5
0.9
0.5
θ
o
7
0o
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
95-12-19
97-08-04
SOT358 -1
1997 Apr 16
EUROPEAN
PROJECTION
29
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
22 SOLDERING
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
22.1
• The package footprint must incorporate solder thieves at
the downstream end.
22.2.3
Reflow soldering
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
22.2.1
22.3
22.3.1
LQFP
SOLDERING BY DIPPING OR BY WAVE
The device may be mounted up to the seating plane but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg(max)). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
If wave soldering cannot be avoided, the following
conditions must be observed:
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
22.4
• The footprint must be at an angle of 45° to the board
direction and must incorporate solder thieves
downstream and at the side corners.
Repairing soldered joints
Fix LQFP and SO by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
Even with these conditions, do not consider wave
soldering LQFP packages LQFP32 (SOT401-1),
LQFP48 (SOT313-2), LQFP64 (SOT314-2 and
SOT414-1), LQFP80 (SOT315-1) or
LQFP100 (SOT407-1).
For DIP, apply a low voltage soldering iron (less than 24 V)
to the lead(s) of the package, below the seating plane or
not more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
SO
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
1997 Apr 16
DIP
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
Wave soldering
Wave soldering is not recommended for LQFP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
22.2.2
METHOD (LQFP AND SO)
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Reflow soldering techniques are suitable for all LQFP and
SO packages. Reflow soldering requires solder paste (a
suspension of fine solder particles, flux and binding agent)
to be applied to the printed-circuit board by screen printing,
stencilling or pressure-syringe dispensing before package
placement.
22.2
PCD3755A; PCD3755E;
PCD3755F
30
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF
generator, 8 kbytes OTP and 128 bytes
PCD3755A; PCD3755E;
PCD3755F
23 DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
24 LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1997 Apr 16
31
Philips Semiconductors – a worldwide company
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101, Fax. +43 1 60 101 1210
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 0044
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580920
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053,
TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Middle East: see Italy
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Internet: http://www.semiconductors.philips.com
© Philips Electronics N.V. 1997
SCA54
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
417027/1200/04/pp32
Date of release: 1997 Apr 16
Document order number:
9397 750 02065