INTEGRATED CIRCUITS DATA SHEET UDA1344TS Low-voltage low-power stereo audio CODEC with DSP features Preliminary specification Supersedes data of 2000 Jan 27 File under Integrated Circuits, IC01 2000 Feb 04 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS FEATURES General • Low power consumption • 3.0 V power supply • System clock of 256fs, 384fs and 512fs • Supports sampling frequencies from 8 to 55 kHz • Non-inverting ADC plus integrated high-pass filter to cancel DC offset Advanced audio configuration • ADC supports 2 V (RMS) input signals • Stereo single-ended input configuration • Overload detector for easy record level control • Separate power control for ADC and DAC • Stereo line output (under microcontroller volume control), no post filter required • Integrated digital interpolation filter plus non-inverting DAC • High linearity, dynamic range and low distortion. • Functions controllable either via L3 microcontroller interface or via static pins GENERAL DESCRIPTION The UDA1344TS is a single-chip stereo Analog-to-Digital Converter (ADC) and Digital-to-Analog Converter (DAC) with signal processing features employing bitstream conversion techniques. The low power consumption and low voltage requirements make the device eminently suitable for use in low-voltage low-power portable digital audio equipment which incorporates recording and playback functions. • UDA1344TS is pin and function compatible with UDA1340M • Small package size (SSOP28) • Easy application. Multiple format input interface • I2S-bus, MSB-justified or LSB-justified 16, 18 and 20 bits format compatible The UDA1344TS supports the I2S-bus data format with word lengths of up to 20 bits, the MSB-justified data format with word lengths of up to 20 bits and the LSB-justified data format with word lengths of 16, 18 and 20 bits. The UDA1344TS also supports three combined data formats with MSB-justified data output and LSB-justified 16, 18 and 20 bits data input. • Three combined data formats with MSB-justified output and LSB-justified 16, 18 and 20 bits input • 1fs input and output format data rate. DAC digital sound processing The sound processing features of the UDA1344TS can be used in the L3 mode only: The UDA1344TS can be controlled either via static pins or via the L3 interface. In the L3 mode the UDA1344TS has special Digital Sound Processing (DSP) features in playback mode such as de-emphasis, volume control, bass boost, treble and soft mute. • Digital tone control, bass boost and treble • Digital dB-linear volume control (low microcontroller load) via L3 microcontroller • Digital de-emphasis for 32, 44.1 and 48 kHz • Soft mute. ORDERING INFORMATION TYPE NUMBER UDA1344TS 2000 Feb 04 PACKAGE NAME DESCRIPTION VERSION SSOP28 plastic shrink small outline package; 28 leads; body width 5.3 mm SOT341-1 2 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supplies VDDA(ADC) ADC analog supply voltage VDDA(DAC) DAC analog supply voltage 2.7 3.0 3.6 V VDDO operational amplifier supply voltage 2.7 3.0 3.6 V VDDD digital supply voltage 2.7 3.0 3.6 V IDDA(ADC) ADC analog supply current operating − 9.0 11.0 mA ADC power-down − 3.5 5.0 mA IDDA(DAC) DAC analog supply current operating − 4.0 6.0 mA DAC power-down − 25 75 µA IDDO IDDD Tamb operational amplifier supply current digital supply current 2.7 3.0 3.6 V operating − 4.0 6.0 mA DAC power-down − 250 350 µA operating − 6.0 9.0 mA DAC power-down − 2.5 4.0 mA ADC power-down − 3.5 5.0 mA −40 − +85 °C ambient temperature Analog-to-digital converter Vi(rms) input voltage (RMS value) notes 1 and 2 − 1.0 − V (THD + N)/S total harmonic distortion-plus-noise to signal ratio at 0 dB − −85 −80 dB at −60 dB; A-weighted − −35 −30 dB S/N signal-to-noise ratio Vi = 0 V; A-weighted − 95 − dB αcs channel separation − 100 − dB Digital-to-analog converter Vo(rms) output voltage (RMS value) notes 3 and 4 − 900 − mV (THD + N)/S total harmonic distortion-plus-noise to signal ratio at 0 dB − −90 −85 dB at −60 dB; A-weighted − −37 − dB S/N signal-to-noise ratio code = 0; A-weighted − 100 − dB αcs channel separation − 100 − dB Power performance PADDA power consumption in record and playback mode − 69 − mW PDA power consumption in playback mode − 42 − mW PAD power consumption in record mode − 37.5 − mW PPD power consumption in power-down mode − 17 − mW Notes 1. The input voltage can be up to 2 V (RMS) when the current through the ADC input pin is limited to approximately 1 mA by using a series resistor. 2. The input voltage to the ADC is inversely proportional to the supply voltage. 3. The output voltage of the UDA1344TS differs from the output voltage of the UDA1340M. 4. The output of the DAC scales proportionally with the supply voltage. 2000 Feb 04 3 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS BLOCK DIAGRAM VDDA(ADC) VSSA(ADC) handbook, full pagewidth 2 3 VINL VADCP 1 VADCN 7 Vref(A) 6 0 dB/6 dB SWITCH 4 5 0 dB/6 dB SWITCH ADC ADC 8 VDDD VSSD DATAO BCK WS DATAI 10 21 DECIMATION FILTER 20 11 MC1 MC2 MP5 DC-CANCELLATION FILTER 18 13 16 DIGITAL INTERFACE 17 14 L3-BUS INTERFACE 15 19 12 MP1 VINR 9 MP2 MP3 MP4 SYSCLK DSP FEATURES INTERPOLATION FILTER UDA1344TS NOISE SHAPER DAC DAC VOUTL 26 24 25 27 VDDO VSSO 23 VDDA(DAC) 22 VSSA(DAC) Fig.1 Block diagram. 2000 Feb 04 4 28 Vref(D) VOUTR MGL441 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS PINNING SYMBOL PIN DESCRIPTION VSSA(ADC) 1 ADC analog ground VDDA(ADC) 2 ADC analog supply voltage VINL 3 ADC input left Vref(A) 4 ADC reference voltage VINR 5 ADC input right VADCN 6 ADC negative reference voltage VSSA(ADC) 1 28 Vref(D) VADCP 7 ADC positive reference voltage VDDA(ADC) 2 27 VSSO MC1 8 mode control 1 input (pull-down) MP1 9 multi purpose pin 1 output VDDD 10 digital supply voltage VSSD 11 digital ground SYSCLK 12 system clock input: 256fs, 384fs or 512fs handbook, halfpage 26 VOUTL VINL 3 25 VDDO Vref(A) 4 24 VOUTR VINR 5 23 VDDA(DAC) VADCN 6 VADCP 7 UDA1344TS 22 VSSA(DAC) MP2 13 multi purpose pin 2 input MC1 8 21 MC2 MP3 14 multi purpose pin 3 input MP1 9 20 MP5 MP4 15 multi purpose pin 4 input BCK 16 bit clock input WS 17 word select input DATAO 18 data output DATAI 19 data input MP2 13 16 BCK MP5 20 multi purpose pin 5 output (pull-down) MP3 14 15 MP4 MC2 21 mode control 2 input (pull-down) VSSA(DAC) 22 DAC analog ground VDDA(DAC) 23 DAC analog supply voltage VOUTR 24 DAC output right VDDO 25 operational amplifier supply voltage VOUTL 26 DAC output left VSSO 27 operational amplifier ground Vref(D) 28 DAC reference voltage 2000 Feb 04 VDDD 10 19 DATAI VSSD 11 18 DATAO 17 WS SYSCLK 12 MGL442 Fig.2 Pin configuration. 5 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS FUNCTIONAL DESCRIPTION Table 1 The UDA1344TS accommodates slave mode only, this means that in all applications the system devices must provide the system clock. The system clock must be locked in frequency to the digital interface input signals. Application modes using input gain stage INPUT GAIN SWITCH MAXIMUM INPUT VOLTAGE Present 0 dB 2 V (RMS) Present 6 dB 1 V (RMS) Absent 0 dB 1 V (RMS) Absent 6 dB 0.5 V (RMS) RESISTOR (12 kΩ) The BCK clock can be up to 128fs, or in other words the BCK frequency is 128 times the Word Select (WS) frequency or less: fBCK = < 128 × fWS. Remarks: 1. The WS edge MUST fall on the negative edge of the BCK clock at all times for proper operation of the digital I/O data interface Decimation filter (ADC) The decimation from 128fs to 1fs is performed in 2 stages. sin x The first stage realizes 3rd-order ------------ characteristic. This x filter decreases the sample rate by 16. 2. The sampling frequency range is from 5 to 55 kHz 3. For MSB- and LSB-justified formats it is important to have a WS signal with a duty factor of 50%. The second stage, a Finite Impulse Response (FIR) filter, consists of 3 half-band filters, each decimating by a factor of 2. Analog-to-Digital Converter (ADC) The stereo ADC of the UDA1344TS consists of two 3rd-order Sigma-Delta modulators. They have a modified Ritchie-coder architecture in a differential switched capacitor implementation. The oversampling ratio is 128. Table 2 In contrast to the UDA1340M, the UDA1344TS supports 1 V (RMS) input signals and can be set, via an external resistor, to support 2 V (RMS) input signals. ITEM CONDITIONS VALUE (dB) Pass-band ripple 0 − 0.45fs ±0.05 >0.55fs −60 0 − 0.45fs 108 DC −1.16 Stop band Dynamic range Overall gain with 0 dB input to the ADC Analog front-end The analog front-end is equipped with a selectable 0 dB or 6 dB gain block. The pin to select the gain switch is given in Section “L3 mode”. This block can be used in applications in which both 1 V (RMS) and 2 V (RMS) input signals are available. DC-cancellation filter (ADC) An optional Infinite Impulse-Response (IIR) high-pass filter is provided to remove unwanted DC components. The operation is selected by the microcontroller via the L3 interface. The filter characteristics are given in Table 3. In applications in which a 2 V (RMS) input signal is used, a 12 kΩ resistor must be connected in series with the input of the ADC. This makes a voltage divider with the internal ADC resistor and makes sure only 1 V (RMS) maximum is input to the IC. Using this application for a 2 V (RMS) input signal, the gain switch must be set to 0 dB. When a 1 V (RMS) input signal is input to the ADC in the same application, the gain switch must be set to 6 dB. Table 3 DC-cancellation filter characteristics ITEM Pass-band ripple Pass-band gain An overview of the maximum input voltages allowed against the presence of an external resistor and the setting of the gain switch is given in Table 1. 2000 Feb 04 Decimation filter characteristics Droop Attenuation at DC Dynamic range 6 CONDITIONS VALUE (dB) − none − 0 at 0.00045fs 0.031 at 0.00000036fs >40 0 − 0.45fs >110 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS Mute (ADC) Multiple format input/output interface On recovery from power-down or switching on of the system clock, the serial data output on pin DATAO is held at LOW level until valid data is available from the decimation filter. This time depends on whether the DC-cancellation filter is selected: The UDA1344TS supports the following data input/output formats: • I2S-bus format with data word length of up to 20 bits • MSB-justified serial format with data word length of up to 20 bits • DC cancel off: 1024 t = ------------- ; t = 23.2 ms at fs = 44.1 kHz fs • LSB-justified serial format with data word lengths of 16, 18 or 20 bits (in L3 mode only) • Combined data formats: • DC cancel on: 12288 t = ---------------- ; t = 279 ms at fs = 44.1 kHz. fs – L3 mode: MSB-justified data output and LSB-justified 16, 18 and 20 bits data input – Static pin mode: MSB-justified data output and LSB-justified 16 and 20 bits data input. Interpolation filter (DAC) The formats are illustrated in Fig.3. Left and right data-channel words are time multiplexed. The digital filter interpolates from 1fs to 128fs by means of a cascade of a recursive filter and an FIR filter. Table 4 Control mode selection Interpolation filter characteristics ITEM CONDITIONS VALUE (dB) Pass-band ripple 0 − 0.45fs ±0.03 Stop band Dynamic range Gain >0.55fs −50 0 − 0.45fs 108 DC −3.5 The UDA1344TS can be used under L3 microcontroller interface control or static pin control. The mode can be set via the mode control pins MC1 and MC2 (see Table 5). Table 5 Mode control pins PIN MC2 PIN MC1 MODE LOW LOW L3 mode Noise shaper (DAC) LOW HIGH Test mode The 3rd-order noise shaper operates at 128fs. It shifts in-band quantization noise to frequencies well above the audio band. This noise shaping technique enables high signal-to-noise ratios to be achieved. The noise shaper output is converted into an analog signal using a Filter Stream Digital-to-Analog Converter (FSDAC). HIGH LOW HIGH HIGH Important: in the L3 mode the UDA1344TS is completely pin and function compatible with the UDA1340M. Filter stream DAC The FSDAC is a semi-digital reconstruction filter that converts the 1-bit data stream of the noise shaper to an analog output voltage. The filter coefficients are implemented as current sources and are summed at virtual ground of the output operational amplifier. In this way very high signal-to-noise performance and low clock jitter sensitivity is achieved. A post-filter is not needed due to the inherent filter function of the DAC. On-board amplifiers convert the FSDAC output current to an output voltage signal capable of driving a line output. The output voltage of the FSDAC scales proportionally with the power supply voltage. 2000 Feb 04 Static pin mode 7 This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... 2 >=8 3 2 3 MSB B2 1 >=8 MSB DATA B2 MSB I2S-BUS FORMAT LEFT WS 1 2 RIGHT >=8 3 1 2 >=8 3 BCK DATA MSB B2 LSB MSB B2 LSB MSB B2 MSB-JUSTIFIED FORMAT WS LEFT RIGHT 16 15 2 8 1 16 B15 LSB MSB 15 2 1 Philips Semiconductors 1 BCK Low-voltage low-power stereo audio CODEC with DSP features dbook, full pagewidth 2000 Feb 04 RIGHT LEFT WS BCK DATA MSB B2 B2 B15 LSB LSB-JUSTIFIED FORMAT 16 BITS WS LEFT RIGHT 18 17 16 15 2 1 18 B17 LSB MSB 17 16 15 2 1 BCK DATA MSB B2 B3 B4 B2 B3 B4 B17 LSB LSB-JUSTIFIED FORMAT 18 BITS WS LEFT 20 RIGHT 19 18 17 16 15 2 1 20 B19 LSB MSB 19 18 17 16 15 2 1 BCK B2 B3 B4 B5 B6 LSB-JUSTIFIED FORMAT 20 BITS Fig.3 Serial interface formats. B2 B3 B4 B5 B6 B19 LSB MBL140 Preliminary specification MSB UDA1344TS DATA Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS Static pin mode MUTE AND DE-EMPHASIS The UDA1344TS is set to static pin mode by setting both pins MC1 and MC2 to HIGH level. The level definition of pin MP2 pin is given in Table 8. Table 8 The controllable features in this mode are: • System clock frequency selection Levels for pin MP2 PIN MP2 • Data input/output format selection LOW • De-emphasis and mute control no de-emphasis and mute 0.5VDDD • Power-down and ADC input level selection. SELECTION HIGH de-emphasis 44.1 kHz mute PINNING DEFINITION INPUT/OUTPUT DATA FORMAT SELECTION The pinning definition in the static pin mode is given in Table 6. The input/output data format can be selected using pins MP1 and MP5 as given in Table 9. Table 6 Table 9 Pinning definition in static pin model PIN Data format selection PIN MP1 PIN MP5 DESCRIPTION SELECTION MP1 data input/output setting LOW LOW input: MSB-justified MP2 three-level pin to select no de-emphasis, de-emphasis or mute LOW HIGH input: I2S-bus HIGH LOW MP3 256fs or 384fs system clock selection input: LSB-justified 20 bits; output: MSB-justified MP4 three-level pin to select ADC power-down, ADC input 1 V (RMS) or ADC input 2 V (RMS) HIGH HIGH input: LSB-justified 16 bits; output: MSB-justified MP5 data input/output setting ADC INPUT VOLTAGE SELECTION AND POWER-DOWN SYSTEM CLOCK In the static pin mode the three-level pin MP4 is used to select 0 or 6 dB gain and power-down. In the static pin mode the options are 256fs and 384fs as given in Table 7. Table 10 Levels for pin MP4 PIN MP4 Table 7 System clock selection PIN MP3 LOW SELECTION LOW 256fs clock frequency HIGH 384fs clock frequency 2000 Feb 04 9 SELECTION ADC power-down 0.5VDDD 6 dB gain HIGH 0 dB gain Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS L3 mode ADC OUTPUT OVERLOAD DETECTION The UDA1344TS is set to the L3 mode by setting both pins MC1 and MC2 to LOW level. In practice the output is used to indicate whenever the output data, in either the left or right channel, is greater than −1 dB (actual figure is −1.16 dB) of the maximum possible digital swing. When this condition is detected pin MP1 is forced to HIGH level for at least 512fs cycles (11.6 ms at fs = 44.1 kHz). This time-out is reset for each infringement. The static pins in this mode are used for: • ADC output overload detection • L3 interface signal input • ADC input voltage selection. The controllable features via the L3 interface and the definition of the control registers are given in Section “L3 interface”. ADC INPUT VOLTAGE SELECTION In the L3 mode pin MP5 is used to select 0 or 6 dB gain. Table 12 Levels for pin MP5 PINNING DEFINITION PIN MP4 The pinning definition in the L3 mode is given in Table 11. Table 11 Pinning definition in L3 mode PIN FUNCTION MP1 ADC output overload detection MP2 L3MODE input MP3 L3CLOCK input MP4 L3DATA input MP5 ADC input voltage selection: 1 V (RMS) or 2 V (RMS) 2000 Feb 04 10 SELECTION LOW 0 dB gain HIGH 6 dB gain Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS L3 INTERFACE Data bits 1 and 0 indicate the type of subsequent data transfer as given in Table 13. The UDA1344TS has a microcontroller input mode. In the microcontroller control mode, all the digital sound processing features and the system controlling features can be controlled by the microcontroller. The controllable features are: Table 13 Selection of data transfer BIT 1 BIT 0 TRANSFER 0 0 data (volume, bass boost, treble, de-emphasis, mute, mode and power control) • Power control 0 1 not used • DC filtering 1 0 status (system clock frequency, data input/output format and DC filter) 1 1 not used • System clock frequency • Data input format • De-emphasis • Volume • Flat/min./max. switch • Bass boost In the event that the UDA1344TS receives a different address, it will deselect its microcontroller interface logic. • Treble • Mute. Data transfer mode The exchange of data and control information between the microcontroller and the UDA1344TS is accomplished through a serial hardware interface comprising the following lines: The selection preformed in the address mode remains active during subsequent data transfers, until the UDA1344TS receives a new address command. The fundamental timing of data transfers is essentially the same as in the address mode and is shown in Fig.5. L3DATA: microcontroller interface data line L3MODE: microcontroller interface mode line The maximum input clock and data rate is 64fs. All transfers are byte wise, i.e. they are based on groups of 8 bits. Data will be stored in the UDA1344TS after the eighth bit of a byte has been received. L3CLOCK: microcontroller interface clock line. Information transfer via the microcontroller bus is LSB first and is organized in accordance with the so called ‘L3’ format, in which two different modes of operation can be distinguished: address mode and data transfer mode. A multibyte data transfer is illustrated in Fig.6. The address mode is required to select a device communicating via the L3 interface and to define the destination registers for the data transfer mode. Data transfer for the UDA1344TS can only be in one direction: input to the UDA1344TS to program its sound processing and other functional features. Programming the sound processing and other features The sound processing and other feature values are stored in independent registers. The first selection of the registers is achieved by the choice of data type that is transferred. This is performed in the address mode by bit 1 and bit 0 (see Table 13). Address mode The address mode is used to select a device for subsequent data transfer and to define the destination registers. The address mode is characterized by L3MODE being LOW and a burst of 8 pulses on L3CLOCK, accompanied by 8 data bits. The second selection is performed by the 2 MSBs of the data byte (bit 7 and bit 6). The other bits in the data byte (bits 5 to 0) is the value that is placed in the selected registers. The fundamental timing is shown in Fig.4. Data bits 7 to 2 represent a 6-bit device address, with bit 7 being the MSB and bit 2 the LSB. The address of the UDA1344TS is 000101 (bits 7 to 2). 2000 Feb 04 11 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS handbook, full pagewidth L3MODE tsu(L3)A th(L3)A tCLK(L3)L tsu(L3)A tCLK(L3)H th(L3)A L3CLOCK Tcy(CLK)(L3) tsu(L3)DA th(L3)DA BIT 7 BIT 0 L3DATA MGL723 Fig.4 Timing in address mode. handbook, full pagewidth tstp(L3) tstp(L3) L3MODE tCLK(L3)L Tcy(CLK)L3 tCLK(L3)H tsu(L3)D th(L3)D L3CLOCK th(L3)DA tsu(L3)DA L3DATA WRITE BIT 7 BIT 0 MGL882 Fig.5 Timing in data transfer mode. 2000 Feb 04 12 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS tstp(L3) handbook, full pagewidth L3MODE L3CLOCK L3DATA address data byte #1 data byte #2 address MGL725 Fig.6 Multibyte data transfer. L3 interface registers When the data transfer of type ‘status’ is selected, the features system clock frequency, data input format and DC filter can be controlled. Table 14 Data transfer of type ‘status’ BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 REGISTER SELECTED 0 0 SC1 SC0 IF2 IF1 IF0 DC SC = system clock frequency (2 bits); see Table 16 IF = data input format (3 bits); see Table 17 DC = DC filter (1 bit); see Table 18 When the data transfer of type ‘data’ is selected, the features volume, bass boost, treble, de-emphasis, mute, mode and power control can be controlled. Table 15 Data transfer of type ‘data’ BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 REGISTER SELECTED 0 0 VC5 VC4 VC3 VC2 VC1 VC0 VC = volume control (6 bits); see Table 19 0 1 BB3 BB2 BB1 BB0 TR1 TR0 BB = bass boost (4 bits); see Table 20 1 0 0 DE1 DE0 MT M1 M0 TR = treble (2 bits); see Table 21 DE = de-emphasis (2 bits); see Table 22 MT = mute (1 bit); see Table 23 M = filter mode (2 bits); see Table 24 1 1 2000 Feb 04 0 0 0 0 PC1 PC0 13 PC = power control (2 bits); see Table 25 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS SYSTEM CLOCK FREQUENCY VOLUME CONTROL A 2-bit value to select the used external clock frequency. A 6-bit value to program the left and right channel volume attenuation. The range is from 0 to −∞ dB in steps of 1 dB. Table 16 System clock frequency settings Table 19 Volume settings SC1 SC0 SELECTION 0 0 512fs 0 1 384fs 0 0 0 0 0 0 0 0 0 0 0 1 0 VC5 VC4 VC3 VC2 VC1 VC0 VOLUME (dB) 1 0 256fs 0 1 1 not used 0 0 0 0 1 0 −1 0 0 0 0 1 1 −2 DATA INPUT FORMAT : : : : : : : A 3-bit value to select the used data format. 1 1 1 0 1 1 −58 1 1 1 1 0 0 −59 1 1 1 1 0 1 −60 1 1 1 1 1 0 −∞ 1 1 1 1 1 1 −∞ Table 17 Data format settings IF2 IF1 IF0 FORMAT 0 0 0 I2S-bus 0 0 1 LSB-justified 16 bits 0 1 0 LSB-justified 18 bits 0 1 1 LSB-justified 20 bits 1 0 0 MSB-justified 1 0 1 input: LSB-justified 16 bits; output: MSB-justified 1 1 0 input: LSB-justified 18 bits; output: MSB-justified 1 1 1 BASS BOOST A 4-bit value to program the bass boost setting. The used set depends on the mode bits M1 and M0. Table 20 Bass boost settings BASS BOOST SETTING BB3 BB2 BB1 BB0 input: LSB-justified 20 bits; output: MSB-justified DC FILTER A 1-bit value to enable the digital DC filter. Table 18 DC filtering DC 2000 Feb 04 SELECTION 0 no DC filtering 1 DC filtering 14 FLAT (dB) MIN. (dB) MAX. (dB) 0 0 0 0 0 0 0 0 0 0 1 0 2 2 0 0 1 0 0 4 4 0 0 1 1 0 6 6 0 1 0 0 0 8 8 0 1 0 1 0 10 10 0 1 1 0 0 12 12 0 1 1 1 0 14 14 1 0 0 0 0 16 16 1 0 0 1 0 18 18 1 0 1 0 0 18 20 1 0 1 1 0 18 22 1 1 0 0 0 18 24 1 1 0 1 0 18 24 1 1 1 0 0 18 24 1 1 1 1 0 18 24 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS TREBLE MODE A 2-bit value to program the treble setting. The used set depends on the mode bits M1 and M0. A 2-bit value to program the mode of the sound processing filters of bass boost and treble. Table 21 Treble settings Table 24 Flat/min./max. switch TREBLE SETTING TR1 M1 M0 MAX. (dB) 0 0 flat 1 min. TR0 FLAT (dB) MIN. (dB) SELECTION 0 0 0 0 0 0 0 1 0 2 2 1 0 min. 1 0 0 4 4 1 1 max. 1 1 0 6 6 POWER CONTROL A 2-bit value to disable the ADC and/or DAC to reduce power consumption. DE-EMPHASIS A 2-bit value to enable the digital de-emphasis filter. Table 25 Power control settings Table 22 De-emphasis settings SELECTION DE1 DE0 SELECTION 0 0 no de-emphasis 0 1 de-emphasis 32 kHz 0 1 0 de-emphasis 44.1 kHz 1 1 de-emphasis 48 kHz PC1 MUTE A 1-bit value to enable the digital mute. Table 23 Mute MT SELECTION 0 no muting 1 muting 2000 Feb 04 15 PC0 ADC DAC 0 off off 0 1 off on 1 0 on off 1 1 on on Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VDDD digital supply voltage − 5.0 V Txtal(max) maximum crystal temperature − 150 °C Tstg storage temperature −65 +125 °C Tamb ambient temperature −40 +85 °C Ves electrostatic handling voltage note 1 −3000 +3000 V note 2 −300 +300 V Notes 1. Equivalent to discharging a 100 pF capacitor via a 1.5 kΩ series resistor. 2. Equivalent to discharging a 200 pF capacitor via a 2.5 µH series inductor. THERMAL CHARACTERISTICS SYMBOL Rth(j-a) PARAMETER CONDITIONS thermal resistance from junction to ambient VALUE UNIT 90 K/W in free air DC CHARACTERISTICS VDDD = VDDA = VDDO = 3.0 V; Tamb = 25 °C; RL = 5 kΩ; all voltages referenced to ground; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supplies; note 1 VDDA(ADC) ADC analog supply voltage 2.7 3.0 3.6 V VDDA(DAC) DAC analog supply voltage 2.7 3.0 3.6 V VDDO operational amplifier supply voltage 2.7 3.0 3.6 V VDDD digital supply voltage 2.7 3.0 3.6 V IDDA(ADC) ADC analog supply current operating − 9.0 11.0 mA ADC power-down − 3.5 5.0 mA operating − 4.0 6.0 mA DAC power-down − 25 75 µA − 4.0 6.0 mA DAC power-down − 250 300 µA IDDA(DAC) DAC analog supply current IDDO operational amplifier supply current operating IDDD digital supply current operating − 6.0 9.0 mA DAC power-down − 2.5 4.0 mA ADC power-down − 3.5 5.0 mA Digital inputs VIH HIGH-level input voltage 0.8VDDD − VDDD + 0.5 V VIL LOW-level input voltage −0.5 − 0.2VDDD V ILI input leakage current − − 10 µA Ci input capacitance − − 10 pF 2000 Feb 04 16 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features SYMBOL PARAMETER UDA1344TS CONDITIONS MIN. TYP. MAX. UNIT Digital outputs VOH HIGH-level output voltage IOH = −2 mA 0.85VDDD − − V VOL LOW-level output voltage IOL = 2 mA − − 0.4 V Three-level inputs: pins MP2 and MP4 VIH HIGH-level input voltage 0.9VDDD − VDDD + 0.5 V VIM MIDDLE-level input voltage 0.4VDDD − 0.6VDDD V VIL LOW-level input voltage −0.5 − 0.1VDDD V referenced to VSSA(ADC) 0.45VDDA 0.5VDDA 0.55VDDA V − 24 − kΩ fi = 1 kHz − 9.8 − kΩ − 20 − pF 0.45VDDA 0.5VDDA 0.55VDDA V Analog-to-digital converter Vref(A) reference voltage Ro(refA) output resistance on pin Vref(A) Ri input resistance Ci input capacitance Digital-to-analog converter Vref(D) reference voltage referenced to VSSA(DAC) Ro(refD) output resistance on pin Vref(D) − 28 − kΩ Ro output resistance of DAC − 0.13 3.0 Ω Io(max) maximum output current (THD + N)/S < 0.1 − %; RL = 5 kΩ 0.22 − mA RL load resistance 3 − − kΩ CL load capacitance − − 200 pF note 2 Notes 1. All power supply pins (VDD and VSS) must be connected to the same external power supply unit. 2. When higher capacitive loads must be driven, a 100 Ω resistor must be connected in series with the DAC output in order to prevent oscillations in the output operational amplifier. 2000 Feb 04 17 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS AC CHARACTERISTICS VDDD = VDDA = VDDO = 3.0 V; fi = 1 kHz; Tamb = 25 °C; RL = 5 kΩ; all voltages referenced to ground; unless otherwise specified. SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT Analog-to-digital converter Vi(rms) input voltage (RMS value) notes 1 and 2 1.0 − V ∆Vi unbalance between channels 0.1 − dB (THD + N)/S total harmonic distortion-plus-noise to signal ratio at 0 dB −85 −80 dB at −60 dB; A-weighted −35 −30 dB Vi = 0 V; A-weighted 95 − dB 100 − dB fripple = 1 kHz; Vripple = 300 mV (p-p) 30 − dB notes 3 and 4 900 − mV 0.1 − dB S/N signal-to-noise ratio αcs channel separation PSRR power supply rejection ratio Digital-to-analog converter Vo(rms) output voltage (RMS value) ∆Vo unbalance between channels (THD + N)/S total harmonic distortion-plus-noise to signal ratio at 0 dB S/N signal-to-noise ratio αcs channel separation PSRR power supply rejection ratio −90 −85 dB at −60 dB; A-weighted −37 − dB code = 0; A-weighted 100 − dB 100 − dB fripple = 1 kHz; Vripple = 300 mV (p-p) 50 − dB Notes 1. The input voltage can be up to 2 V (RMS) when the current through the ADC input pin is limited to approximately 1 mA by using a series resistor. 2. The input voltage to the ADC is inversely proportional with the supply voltage. 3. The output voltage of the UDA1344TS differs from the output voltage of the UDA1340M. 4. The output of the DAC scales proportionally with the supply voltage. 2000 Feb 04 18 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS TIMING VDDD = VDDA = VDDO = 2.7 to 3.6 V; Tamb = −40 to +85 °C; RL = 5 kΩ; all voltages referenced to ground; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT System clock input (see Fig.7) Tsys system clock cycle time tCWH system clock HIGH time tCWL system clock LOW time fsys = 256fs 78 88 262 ns fsys = 384fs 52 59 174 ns fsys = 512fs 39 44 132 ns fsys < 19.2 MHz 0.30Tsys − 0.70Tsys ns fsys ≥ 19.2 MHz 0.40Tsys − 0.60Tsys ns fsys < 19.2 MHz 0.30Tsys − 0.70Tsys ns fsys ≥ 19.2 MHz 0.40Tsys − 0.60Tsys ns − − 64fs Hz − − ns 100 − − ns Serial interface input/output data (see Fig.8) fBCK bit clock frequency Tcy(BCK) bit clock cycle time tBCKH bit clock HIGH time tBCKL bit clock LOW time 100 − − ns tr rise time − − 20 ns tf fall time − − 20 ns tsu(WS) word select set-up time 20 − − ns th(WS) word select hold time 10 − − ns tsu(DATAI) data input set-up time 20 − − ns th(DATAI) data input hold time 0 − − ns th(DATAO) data output hold time td(DATAO−BCK) data output to bit clock delay td(DATAO−WS) data output to word select delay Tcy(s) = cycle time of sample frequency T cy(s) ------------64 0 − − ns from BCK falling edge − − 80 ns − − 80 ns 500 − − ns from WS edge for MSB-justified format L3 interface input (see Figs 4 and 5) Tcy(CLK)L3 L3CLOCK cycle time tCLK(L3)H L3CLOCK HIGH time 250 − − ns tCLK(L3)L L3CLOCK LOW time 250 − − ns tsu(L3)A L3MODE set-up time for address mode 190 − − ns th(L3)A L3MODE hold time for address mode 190 − − ns tsu(L3)D L3MODE set-up time for data transfer mode 190 − − ns th(L3)D L3MODE hold time for data transfer mode 190 − − ns tstp(L3) L3MODE stop time 190 − − ns tsu(L3)DA L3DATA set-up time in data transfer and address mode 190 − − ns th(L3)DA L3DATA hold time in data transfer and address mode 30 − − ns 2000 Feb 04 19 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS tCWH handbook, full pagewidth tCWL MGL443 Tsys Fig.7 System clock timing. handbook, full pagewidth WS tr t BCKH t d(DATAO-BCK) t h(WS) tf t su(WS) BCK t BCKL Tcy(BCK) t d(DATAO-WS) t h(DATAO) DATAO t su(DATAI) t h(DATAI) DATAI MGS756 Fig.8 Serial interface timing. 2000 Feb 04 20 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS APPLICATION INFORMATION VDD1 8LM32A07 R21 1Ω L2 VDD2 8LM32A07 C12 100 µF (16 V) ground C2 C11 100 µF (16 V) R24 system clock SYSCLK 47 Ω DATAO BCK WS DATAI MP1 overload flag left input VDD2 100 µF (16 V) C21 C25 C29 100 nF (63 V) 100 nF (63 V) 100 nF (63 V) VSSD 2 1 R28 1Ω C9 10 Ω 100 µF (16 V) VSSA(ADC) VDDA(ADC) R30 handbook, full pagewidth VDD1 L1 3V VADCN VADCP 6 7 VDDD 10 11 12 18 4 C22 100 nF (63 V) 16 17 C1 VINL 9 UDA1344TS 3 24 right input C6 MP4 13 28 14 27 25 23 22 VDDO VSSA(DAC) C26 C27 100 nF (63 V) 100 nF (63 V) C7 C10 100 µF (16 V) R25 1Ω 100 µF (16 V) VDD1 Fig.9 Application diagram. 21 X2 left output R22 10 kΩ R26 100 Ω X3 right output R27 10 kΩ Vref(D) C23 100 nF (63 V) 15 VSSO R23 100 Ω C8 47 µF (16 V) VINR 5 MP3 2000 Feb 04 VOUTR 47 µF (16 V) MP2 C5 VOUTL 47 µF (16 V) 47 µF (16 V) X5 C3 47 µF (16 V) 19 26 X4 Vref(A) C4 47 µF (16 V) MGL444 VDDA(DAC) R29 1Ω VDD1 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS PACKAGE OUTLINE SSOP28: plastic shrink small outline package; 28 leads; body width 5.3 mm D SOT341-1 E A X c HE y v M A Z 28 15 Q A2 A (A 3) A1 pin 1 index θ Lp L 1 14 bp e detail X w M 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) θ mm 2.0 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 10.4 10.0 5.4 5.2 0.65 7.9 7.6 1.25 1.03 0.63 0.9 0.7 0.2 0.13 0.1 1.1 0.7 8 0o Note 1. Plastic or metal protrusions of 0.20 mm maximum per side are not included. OUTLINE VERSION SOT341-1 2000 Feb 04 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION ISSUE DATE 95-02-04 99-12-27 MO-150 22 o Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS SOLDERING If wave soldering is used the following conditions must be observed for optimal results: Introduction to soldering surface mount packages • Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 652 90011). • For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; There is no soldering method that is ideal for all surface mount IC packages. Wave soldering is not always suitable for surface mount ICs, or for printed-circuit boards with high population densities. In these situations reflow soldering is often used. – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. Reflow soldering The footprint must incorporate solder thieves at the downstream end. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. • For packages with leads on four sides, the footprint must be placed at a 45° angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. Several methods exist for reflowing; for example, infrared/convection heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical reflow peak temperatures range from 215 to 250 °C. The top-surface temperature of the packages should preferable be kept below 230 °C. Typical dwell time is 4 seconds at 250 °C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Wave soldering Manual soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. To overcome these problems the double-wave soldering method was specifically developed. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 °C. 2000 Feb 04 23 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS Suitability of surface mount IC packages for wave and reflow soldering methods SOLDERING METHOD PACKAGE REFLOW(1) WAVE BGA, LFBGA, SQFP, TFBGA not suitable suitable(2) HBCC, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, SMS not PLCC(3), SO, SOJ suitable LQFP, QFP, TQFP SSOP, TSSOP, VSO suitable suitable suitable not recommended(3)(4) suitable not recommended(5) suitable Notes 1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”. 2. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 4. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 2000 Feb 04 24 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS NOTES 2000 Feb 04 25 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS NOTES 2000 Feb 04 26 Philips Semiconductors Preliminary specification Low-voltage low-power stereo audio CODEC with DSP features UDA1344TS NOTES 2000 Feb 04 27 Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstraße 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW, Tel. +48 22 5710 000, Fax. +48 22 5710 001 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SÃO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2886, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 3341 299, Fax.+381 11 3342 553 For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 Internet: http://www.semiconductors.philips.com SCA 69 © Philips Electronics N.V. 2000 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 753503/25/03/pp28 Date of release: 2000 Feb 04 Document order number: 9397 750 06836