USB-KW2x Hardware Reference Manual

USB-KW2X Hardware
Reference Manual
Document Number: USB-KW2XHWRM
Rev. 0.3
08/2014
How to Reach Us:
Home Page:
freescale.com
Web Support:
freescale.com/support
Information in this document is provided solely to enable system and software
implementers to use Freescale products. There are no express or implied copyright
licenses granted hereunder to design or fabricate any integrated circuits based on the
information in this document.
Freescale reserves the right to make changes without further notice to any products
herein. Freescale makes no warranty, representation, or guarantee regarding the
suitability of its products for any particular purpose, nor does Freescale assume any
liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or incidental
damages. “Typical” parameters that may be provided in Freescale data sheets and/or
specifications can and do vary in different applications, and actual performance may
vary over time. All operating parameters, including “typicals,” must be validated for each
customer application by customer’s technical experts. Freescale does not convey any
license under its patent rights nor the rights of others. Freescale sells products pursuant
to standard terms and conditions of sale, which can be found at the following address:
freescale.com/SalesTermsandConditions.
Freescale, the Freescale logo, AltiVec, CodeWarrior, ColdFire, ColdFire+,Energy
Efficient Solutions logo, PowerQUICC, QorIQ, StarCore, Symphony, and VortiQa are
trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. CoreNet,
Layerscape, QorIQ Qonverge, QUICC Engine, Tower, and Xtrinsic are trademarks of
Freescale Semiconductor, Inc. All other product or service names are the property of
their respective owners. ARM and Cortex are registered trademarks of ARM Limited.
ARMnnn is the trademark of ARM Limited.
© 2014 Freescale Semiconductor, Inc.
About This Book
Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Chapter 1
Safety Information
1.1
1.1.1
1.1.2
1.1.3
1.1.4
1.2
1.2.1
1.3
1.4
FCC Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exposure Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulatory Approval For Canada (IC RSS 210) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26 PART 5 – Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrostatic Discharge Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disposal Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-1
1-1
1-1
1-2
1-2
1-2
1-2
Chapter 2
USB-KW24D512 Development Platform Overview and Description
2.1
2.2
2.2.1
2.3
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB-KW24D512 Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software and Driver Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-1
2-1
2-3
Chapter 3
USB-KW24D512
3.1
3.1.1
3.1.2
3.1.3
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.3
3.3.1
USB-KW24D512 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCB Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Form Factor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Board Level Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RF Performance and Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB-KW24D512 Peripheral Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic, Board Layout, and Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1
3-1
3-1
3-2
3-3
3-4
3-5
3-5
3-6
3-7
3-9
Chapter 4
PCB Manufacturing Specifications
4.1
4.2
Single PCB Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Panelization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
iii
4.3
4.4
4.5
4.6
4.7
4.8
4.9
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Solder Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Silk Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical PCB Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hole Specification/Tool Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
File Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
4-3
4-3
4-3
4-3
4-3
4-4
USB-KW2x Hardware Reference Manual, Rev. 0.3
iv
Freescale Semiconductor
About This Book
This manual describes Freescale’s MKW2xDxxx development platform hardware. The MKW2xDxxx is
an IEEE® 802.15.4 compliant evaluation environment based on the Freescale MKW2xDxxx device. The
MKW2xDxxx family is Freescale's latest generation ZigBee™ platform, which incorporates a complete
low power 2.4 GHz radio frequency transceiver and a Kinetis family low power, mixed-signal ARMR
eCortex™- M4 MCU into a single package. This family of products is targeted to meet the higher
performance requirements of ZigBee Pro and ZigBee IP based applications, especially Smart Energy and
Commercial Building Automation. This product is a cost-effective solution that matches or exceeds
competitive solutions.
Audience
This manual is intended for system designers.
Organization
This document is organized into the following chapters.
Chapter 1
Safety Information — Highlights some of the FCC requirements.
Chapter 2
MKW2xDxxx Development Platform Overview and Description — Provides an
overview of the boards that comprise the MKW2xDxxx development platform.
USB-KW24D512 — This chapter details the USB-KW24D512 evaluation board.
PCB Manufacturing Specifications — This chapter provides the specifications
used to manufacture the various MKW2xDxxx printed circuit boards (PCBs).
Chapter 3
Chapter 4
Revision History
The following table summarizes revisions to this document since the previous release (Rev. 0.0).
Revision History
Location
Revision
Entire document
First public release
Entire document
Rev. 0.1, Rename KW24512-USB to USB-KW24D512 development board.
Entire document
Rev. 0.2, Update Schematic Board Revision to A3.
Chapter 3
Rev. 0.3, Update Schematic Board Revision to B.
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
v
Definitions, Acronyms, and Abbreviations
The following list defines the acronyms and abbreviations used in this document.
ADC
Analog to Digital Converter
AES
Advanced Encryption Standard
CTS
DAC
I2C
ISM
Clear to Send
Digital to Analog Converter
Inter-Integrated Circuit is a multi-master serial computer bus
Industrial Scientific Medical 2.4 GHz radio frequency band
JTAG
LGA
MAC
MCU
Joint Test Action Group
Land Grid Array
Media Access Controller
Microcontroller Unit
PCB
PiP
PWM
Printed circuit board
Platform in Package
Pulse-width modulation
RCM
REM
RTS
SMA Connector
Remote Control Module
Remote Extender Board
Request to Send
SubMiniature version “A” connector
SoC
SPI
SSI
TACT Switch
System on Chip
Serial Peripheral Interface
Synchronous Serial Interface
A switch that provides a slight “snap” or “click” to the user to indicate function.
TELCO
TWR
USB
VCP
Telephone Company
Tower System
Universal Serial Bus
Virtual Com Port
USB-KW2x Hardware Reference Manual, Rev. 0.3
vi
Freescale Semiconductor
Chapter 1
Safety Information
1.1
FCC Guidelines
This equipment is for use by developers for evaluation purposes only and must not be incorporated into
any other device or system. This device may not be sold to the general public. Integrators will be
responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
FCC approval of this device only covers the original configuration of this device as supplied. Any
modifications to this product, including changes shown in this manual, may violate the rules of the Federal
Communications Commission and Industry Canada and make operation of the product unlawful.
1.1.1
Labeling
FCC labels are physically located on the back of the board.
1.1.2
Operating Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired
operation.
1.1.3
Exposure Limits
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The antenna(s) used for this equipment must be installed to provide a separation distance of at least 8
inches (20cm) from all persons.
1.1.4
Antenna Restrictions
An intentional radiator is designed to ensure that no antenna other than that furnished by the responsible
party is used with the device. The use of a permanently attached antenna or of an antenna that uses a unique
coupling to the intentional radiator is considered sufficient to comply with the provisions of this Section.
The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of
a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier
current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or
15.221. Further, this requirement does not apply to intentional radiators that must be professionally
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
1-1
Safety Information
installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional
radiators which, in accordance with Section 15.31(d), must be measured at the installation site. However,
the installer is responsible for ensuring that the proper antenna is employed so that the limits in this Part
are not exceeded.
1.2
Regulatory Approval For Canada (IC RSS 210)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
1.2.1
26 PART 5 – Appendix
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
1.3
Electrostatic Discharge Considerations
Although damage from electrostatic discharge (ESD) is much less common on these devices than on early
CMOS circuits, normal handling precautions should be used to avoid exposure to static discharge.
Qualification tests are performed to ensure that these devices can withstand exposure to reasonable levels
of static without suffering any permanent damage.
All ESD testing is in conformity with the JESD22 Stress Test Qualification for Commercial Grade
Integrated Circuits. During the device qualification ESD stresses were performed for the human body
model (HBM), the machine model (MM) and the charge device model (CDM).
All latch-up test testing is in conformity with the JESD78 IC Latch-Up Test.
When operating or handling the development boards or components, Freescale strongly recommends
using at least the grounding wrist straps plus any or all of the following ESD dissipation methods:
• Flexible fabric, solid fixed size, or disposable ESD wrist straps
• Static control workstations, static control monitors and table or floor static control systems
• Static control packaging and transportation materials and environmental systems
1.4
Disposal Instructions
This product may be subject to special disposal requirements. For product disposal instructions, refer to
www.freescale.com/productdisposal.
USB-KW2x Hardware Reference Manual, Rev. 0.3
1-2
Freescale Semiconductor
Chapter 2
USB-KW24D512 Development Platform Overview and
Description
2.1
Introduction
The USB-KW24D512 development platform is an evaluation environment based on the Freescale
MKW24D512 SIP device (MKW2x).
The MKW2x device family is Freescale's latest generation ZigBee™ platform which incorporates a
complete low power IEEE® 802.15.4 Standard 2.4 GHz radio frequency transceiver and a Kinetis family
low power, mixed-signal ARM Cortex™- M4 MCU into a single package.
Freescale supplements the MKW2x with tools and software that include hardware evaluation and
development boards, software development IDE and applications, drivers, custom PHY usable with
Freescale’s IEEE 802.15.4 compatible MAC.
The USB-KW24D512 development platform contains the MKW24D512 device with 32 MHz reference
oscillator crystal, RF circuitry including antenna, and supporting circuitry in a USB stick hardware format.
The board is a standalone and can be used for application development or as a packet sniffer.
Whether the USB-KW24D512 is used in a simple standalone application or in combination with another
boards, Freescale provides a complete software development environment called the Freescale BeeKit
Wireless Connectivity Toolkit (BeeKit). BeeKit is a comprehensive codebase of wireless networking
libraries, application templates, and sample applications. A wide range of software functionality are
available to complement the USB-KW24D512 platform and these are provided as codebases within
BeeKit.
2.2
2.2.1
Board Features
USB-KW24D512 Board
The USB-KW24D512 development platform contains the MKW24D512 device and is one of the simplest
reference designs utilizing the on chip USB block for power and communication. The USB-KW24D512
is a small form factor self-contained board for evaluation of wireless applications and can be used as packet
sniffer. The USB Type A connection is used with USB enabled hardware such as a computer.
Figure 2-1 shows the USB-KW24D512 development platform.
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
2-1
USB-KW24D512 Development Platform Overview and Description
Figure 2-1. USB-KW24D512
The USB-KW24D512 development platform includes the following Features:
• Freescale’s low-power MKW24D512 SIP ZigBee™ platform
• Fully compliant IEEE 802.15.4 Standard 2006 transceiver supports 250 kbps O-QPSK data in 5.0
MHz channels and full spread-spectrum encode and decode.
• USB form factor for reference design and small footprint, low cost RF node
— Differential input/output port used with external balun for single port operation
— Low external component count
— Programmable output power from –32 dBm to +8 dBm feed to the Antenna
— Receiver sensitivity: –101 dBm, typical (@1% PER for 20 byte payload packet) feed to the
antenna
• Integrated PCB Folded F-type antenna
• 32 MHz reference oscillator
• 2.4 GHz frequency operation (ISM)
• Programmable frequency clock output (CLK_OUT)
• Full speed USB 2.0
• Cortex 10-pin (0.05”) JTAG debug port for target MCU
• 2 blue LED indicators
• 1 push button switch
• 1 Reset push button
Figure 2-2 shows a simplified block diagram of the Freescale USB-KW24D512 board.
USB-KW2x Hardware Reference Manual, Rev. 0.3
2-2
Freescale Semiconductor
USB-KW24D512 Development Platform Overview and Description
Figure 2-2. Simplified USB-KW24D512 Block Diagram
2.3
Software and Driver Considerations
Install the BeeKit Wireless Connectivity Toolkit package found under Software and Tools at the following
URL before proceeding to use the boards:
• www.freescale.com\zigbee
When users first connect a KW2x based platform to a PC, they may be prompted to install drivers.
Platform drivers can be found under the installation Beekit folder as denoted below. Once BeeKit is
installed, do not allow Windows to automatically search for and install the drivers. Instead, select manual
installation and steer Windows to the following directory:
• C:\Program Files\Freescale\Drivers
Follow the instructions as they appear on the screen to complete driver installation.
NOTE
If the BeeKit software package is installed in another drive or directory,
indicate the Drivers proper folder location where BeeKit was installed.
If BeeKit is not installed, consider the following:
• When prompted, download the appropriate Windows driver and follow the instructions to complete
the driver installation.
• The required drivers to be installed will depend on the reference design platform.
— The KW2x boards come imaged with MSD OpenSDA firmware for board to PC connectivity.
The target in pre-loaded with the SMAC Connectivity Test application.
— Use the OpenSDA USB port (J15) to connect via Virtual COM Port (VCP) using P&E’s
OpenSDA Windows driver (See the TWR-OSDAUG.pdf guide).
For additional information about our 2.4 GHz Kinetis family ZigBee™ platforms, refer to the following:
• www.freescale.com\KW2x
• TWR-OSDAUG - OpenSDA User’s Guide
• SMACDAUG - SMAC User’s Guide
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
2-3
USB-KW24D512 Development Platform Overview and Description
USB-KW2x Hardware Reference Manual, Rev. 0.3
2-4
Freescale Semiconductor
Chapter 3
USB-KW24D512
3.1
USB-KW24D512 Overview
The USB-KW24D512 is an evaluation board based on the Freescale MKW24D512 device. The
USB-KW24D512 provides a platform to evaluate the USB-KW24D512 SIP IC, develop software and
applications. The core device is accompanied by the 32 MHz reference oscillator crystal, RF circuitry
including a printed board antenna, and supporting circuitry.
This basic board is intended as the core PCB for USB-KW24D512 evaluation and application
development and can be used as a simple standalone evaluation solution or use a packet sniffer.
3.1.1
PCB Board Features
The USB-KW24D512 provides the following features:
• USB small form factor
• 4-Layer metal, 0.062 inch thick FR4 board
• LGA footprint and power supply bypass
• Printed metal folded F-Antenna
• 32 MHz reference oscillator crystal
3.1.2
Form Factor
Figure 3-1 shows the USB-KW24D512 connector and header locations.
Figure 3-1. USB-KW24D512
Figure 3-2 shows a footprint of the USB-KW24D512 with the location of the header and connectors
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
3-1
USB-KW24D512
Figure 3-2. USB-KW24D512 Top Side (Component Side) Footprint
3.1.3
Board Level Specifications
Table 3-1. USB-KW24D512 Specifications
Parameter
Min
Typ
Max
Units
61.4 x 18.5
2.42 x 0.73
mm
inches
Notes/Conditions
General
Size (PCB: X, Y)
Layer build (PCB)
1.57
0.062
mm 4-Layer
inches
Dielectric material (PCB)
FR4
Power
Current consumption
mA
Refer to datasheet
• Operating temperature is limited to +70
°C due to switches. Basic circuit is good
for a maximum temperature of +85 °C.
Temperature
Operating temperature (see note)
-40
+25
+70
°C
Storage temperature
-30
+25
+70
°C
2480
MHz
All 16 channels in the2450 MHz band
RF
802.15.4 Frequency range
2405
RF Receiver
Saturation (maximum input level)
+10
dBm
Datasheet
Sensitivity for 1% packet error rate (PER)
(+25 °C)
-102
dBm
Datasheet
RF Transmitter
USB-KW2x Hardware Reference Manual, Rev. 0.3
3-2
Freescale Semiconductor
USB-KW24D512
Table 3-1. USB-KW24D512 Specifications (continued)
Parameter
RF Power Output
Min
Typ
-32
Max
Units
Notes/Conditions
+8
dBm
Programmable in 2dB steps.
At the antenna feed with no trap. 1.
2nd harmonic
<-50
<-40
dBm
Datasheet
3rd harmonic
<-50
<-40
dBm
Datasheet
Regulatory Approval
FCC
Product is approved accordingly to the FCC
part 15 standard
CE (ETSI)
Product is approved accordingly to the EN
300 328 V1.7.1 (2006-10) standard
CE (EMC)
Product is approved accordingly to the EN
301 489-1 V1.6.1 (2005-09) and EN 301
489-17 V1.2.1 (2002-08) standards
Safety
UL
Product is approved accordingly to the IEC
60950-1 and EN 60950-1, First Edition
standards
Environment
RoHS
Product complies with the EU Directive
2002/95/EC of 27 January 2003
WEEE
Product complies with the EU Directive
2002/95/EC of 27 January 2003
1
Trap will add 1 to 2 dB of loss.
3.2
Functional Description
The USB-KW24D512 is built around Freescale’s MKW24D512 63-pin (56-pin usable) LGA platform.
This board is intended as a simple evaluation platform and as a building block for application development.
The 4-layer board provides the MKW24D512 with its required RF circuitry, 32 MHz reference oscillator
crystal, and power supply bypassing. The layout for this base level functionality can be used as a reference
layout by the user target board. Figure 3-3 shows a simple block diagram.
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
3-3
USB-KW24D512
Figure 3-3. USB-KW24D512 Block Diagram
3.2.1
RF Performance and Considerations
USB-KW24D512 transceiver includes a 1mW nominal output power, PA with internal voltage controlled
oscillator (VCO), integrated transmit/receive switch, on-board power supply regulation, and full
spread-spectrum encoding and decoding. The USB-KW24D512 utilizes a minimum number of
components while providing good RF performance. Key specifications for USB-KW24D512 are:
• Nominal output power is set to 0 dBm
• Programmable output power from –32 dBm to +8 dBm measured at the antenna feed
• Typical sensitivity is -101 dBm (@1% PER for 25 °C) measured at the antenna feed
• Frequency range is 2360 to 2480 MHz
• Folded “F” printed metal antenna for a small footprint, low cost design
• Uses a minimum number of RF marching components and external 50:50 balun
An external 50 (unbal): 50(bal) balun connects a single-ended 50-ohm port to the differential RF port of
the MKW24D512 radio. The layout has provision for out-of-band signal suppression (components L5 and
C19) if required. Figure 3-4 shows the typical topology for the RF circuitry. The RF switch J4 has been
designed in for measurement purposes and is left as DNP.
Figure 3-4. USB-KW24D512 RF Circuitry
USB-KW2x Hardware Reference Manual, Rev. 0.3
3-4
Freescale Semiconductor
USB-KW24D512
3.2.2
Clocks
The USB-KW24D512 provides one clock:
• 32 MHz Reference Oscillator — Figure 3-5 shows the external 32 MHz external crystal Y1. This
mounted crystal must meet the specifications outlined in the AN3251 application note. The IEEE
802.15.4 Standard requires that the frequency be accurate to less that +/-40 ppm.
— Capacitors C10 and C11 provide the bulk of the crystal load capacitance. Onboard trim
capacitors can be programmed to center the frequency. At 25°C, it is desired to have the
frequency accurate to +/-10 ppm or less to allow for temperature variation.
— To measure the 32 MHz oscillator frequency, signal CLK_OUT (TP5) can optionally be
programmed to provide a buffered output clock signal.
Figure 3-5. USB-KW24D512 32 MHz Reference Oscillator Circuit
3.2.3
Power Management
The USB-KW24D512 power management circuit is shown in Figure 3-6.
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
3-5
USB-KW24D512
Figure 3-6. USB-KW24D512 Power Management Circuit
The USB-KW24D512 is powered via the USB type A connector as shown in Figure 3-6.,
“USB-KW24D512 Power Management Circuit”; the MKW24D512 device has an on-board USB port
which is configured to provide both power and serial communication with the target MCU.
3.2.4
USB-KW24D512 Peripheral Functions
The USB-KW24D512 includes two switch buttons; one for general purpose peripheral function to assist
in implementing targeted applications and the other is for board hardware Reset.
In the same situation the USB-KW24D512 includes two LEDs for general purpose peripheral function to
assist on applications.
USB-KW2x Hardware Reference Manual, Rev. 0.3
3-6
Freescale Semiconductor
Freescale Semiconductor
3.3
Schematic, Board Layout, and Bill of Material
Figure 3-7. USB-KW24D512 Schematic
5
4
3
2
1
V_MCU
3V3
IN CIRCUIT
TEST GND
PROBING
V_USB
C1
5pF
C2
1000pF
C3
0.33UF
TP28
DNP
VDD_RF
VDD_RF
V_MCU
V_MCU
VDD_IF
D
VREFH
C5
1000pF
C4
5pF
V_MCU
VDD_PA
SH1
VDD_IF
C8
0.1UF
C24
1000pF
GND
C13
0.47UF
D
C12
33PF
C7
0.1UF
DNP
VDD_REGD
C26
5pF
VDD_PA
C6
0.1UF
0
C9
0.1UF
TP19
V_RF
VREFL
SH2
GPIO1
GPIO2
26
27
VREFH
VREFL
32
42
55
VBAT_MCU
VBAT2_RF
VBAT_RF
43
52
53
54
25
28
TAMPER0/RTC_WAKEUP
41
TP_RX_SWITCH
TP_TX_SWITCH
PTE0/MADC0_SE10/SPI1_PCS1/UART1_TX/MTRACE_CLKOUT/I2C1_SDA/RTC_CLKOUT
PTE1/LLWU_P0/MADC0_SE11/SPI1_SOUT/UART1_RX/MTRACE_D3/I2C1_SCL/SPI1_SIN
PTE2/LLWU_P1/MADC0_DP1/SPI1_SCK/UART1_CTS/MTRACE_D2
PTE3/MADC0_DM1/SPI1_SIN/UART1_RTS/MTRACE_D1/SPI1_SOUT
PTE4/LLWU_P2/SPI1_PCS0/MTRACE_D0
RESET
46
47
RX_SWITCH
TX_SWITCH
33
34
35
36
37
39
40
PTA0/JTAG_TCLK/SWD_CLK/EZP_CLK/UART0_CTS/UART0_COL/FTM0_CH5
PTA1/JTAG_TDI/EZP_DI/UART0_RX/FTM0_CH6
PTA2/JTAG_TDO/TRACE_SWO/EZP_DO/UART0_TX/FTM0_CH7
PTA3/JTAG_TMS/SWD_DIO/UART0_RTS/FTM0_CH0
PTA4/LLWU_P3/NMI/EZP_CS/FTM0_CH1
PTA18/EXTAL0/FTM0_FLT2/FTM_CLKIN0
PTA19/XTAL0/FTM1_FLT0/FTM_CLKIN1/LPTMR0_ALT1
4
5
6
7
C16
33PF
15
16
17
18
19
KW24_USB_DP
KW24_USB_DN
49
50
RF_OUTP
RF_OUTN
Z_RF_P
C
Z1
0
C17
1PF
C18
BAL_C
10PF
4
6
2
5
3
MM8030-2600B
J4
RF_50
1
2400MHz 50OHM
Z_RF_N
NC_57
NC_58
NC_59
NC_60
NC_61
NC_62
57
58
59
60
61
62
DNP
PROBE
1
2
IN
OUT
ANT1
2
1
C20
L3
2.2nH
RF_ANT
1.8pF
0
MEANDER_ANT_HORZ
C19
HARMONIC TRAP
10PF
48
51
63
64
65
MKW24D512V
21
22
R3
PTC4/LLWU_P8/SPI0_PCS0/UART1_TX/FTM0_CH3/CMP1_OUT
PTC5/LLWU_P9/SPI0_SCK/LPTMR0_ALT2/I2S0_RXD0/CMP0_OUT
PTC6/LLWU_P10/CMP0_IN0/SPI0_SOUT/PDB0_EXTRG/I2S0_RX_BCLK/I2S0_MCLK
PTC7/CMP0_IN1/SPI0_SIN/USB_SOF_OUT/I2S0_RX_FS
EP_GND1
EP_GND2
PTC4
RF_OUTP
RF_OUTN
GND_PA1
GND_PA2
GND_PA3
CLK_OUT
TP5
C15
0.33UF
PTD4
PTD5
R2
USB0_DP
USB0_DM
C
PTA0
PTA1
PTA2
PTA3
VDD_REGD
4
RST_TGTMCU_B
8
9
10
11
12
13
14
TP2
TP_ANT_A
TP_ANT_B
3
29
TAMPER0
TP3
TP4
PTD1/ADC0_SE5B/SPI0_SCK/UART2_CTS
PTD2/LLWU_P13/SPI0_SOUT/UART2_RX/I2C_SCL/GPIO4_BSM_DATA
PTD3/SPI0_SIN/UART2_TX/I2C_SDA/GPIO5_BSM_CLK
PTD4/LLWU_P14/MADC0_SE21/SPI0_PCS1/UART0_RTS/FTM0_CH4/EWM_IN/GPIO_BSM_FRAME
PTD5/ADC0_SE6B/SPI0_PCS2/UART0_CTS/UART0_COL/FTM0_CH5/EWM_OUT
PTD6/LLWU_P15/ADC0_SE7B/SPI0_PCS3/UART0_RX/FTM0_CH6/FTM0_FLT0
PTD7/MADC0_SE22/CMT_IRO/UART0_TX/FTM0_CH7/FTM0_FLT1
EXTAL_32M
XTAL_32M
2
3
44
45
1
1
56
VDD_REGD
VDD_PA
VDD_IF
VDD_RF
XTAL32
EXTAL32
TP1
ANT_A
ANT_B
2
EXTAL_32M
XTAL_32M
B
B
A
K24_USB_SHLD
V
RT1
2
V_USB_CONN
A1
A2
A3
A4
L5
330 OHM
USB_DN R7
USB_DP R8
1
2
2
L4
TP6
V_USB_CONN_IND1
C27
47PF
DNP
C25
47PF
DNP
TP9
1
C21
KW24_USB_DP
33
1
D2
BLUE
PTC4
D3
BLUE
Y1
EXTAL_32M
2
60OHM
KW24_USB_DN
33
USB_TYPE_A
SW1
V_USB
MINISMDC050F-2
S1
C10
11pF
4
2
SKQYAFE010
XTAL_32M
3
1.0UF
32MHZ
C11
11pF
TP10
C
D-
PTD5_LED
D+
C
G
PTD4_LED
J5
S2
A
V_LED
1
USB-KW2x Hardware Reference Manual, Rev. 0.3
30
31
VDDA
VSSA
23
24
VOUT33
VREGIN
R1
1.0M
VDD_MCU
VDD_MCU
20
38
0
U1
TP7
R9
390
TP8
R10
390
V_MCU
RESET
V_LED
2
V_LED
A
D1
GREEN
0.1UF
2.2UF
V_MCU
R12
0
V_RF
SKQYAFE010
C30
1000pF
MCU VOLTAGE
R14
TP13
RF VOLTAGE
330
PIN FUNCTIONS USED
J1
LED_PWR_R
TP12
0
R11
V_MCU
V_MCU
C
C29
RST_TGTMCU_B
1
TP11
LED VOLTAGE
C28
PTD5
R13
10K
DNP
SW2
A
3V3
PTD4
32MHz XTAL
POWER ON
1
3
5
7
9
NET NAMES
R6
10K
A
2
4
6
8
10
PTA3
JTAG_TMS/SWD_DIO
JTAG_TCLK/SWD_CLK/EZP_CLK
PTA0
PTA2
JTAG_TDO/TRACE_SWO/EZP_DO
PTA1
JTAG_TDI/EZP_DI
RST_TGTMCU_B
MH1
MH_80mil
HDR 2X5
MH2
MH_80mil
MH3
MH_80mil
MH4
MH_80mil
TP14
TP15
TP16
TP17
TP18
4
3
FCP: ___
FIUO: X
PUBI: ___
MAIN SCHEMATIC
1
1
1
1
1
1
2
Page Title:
Size
C
Document Number
SCH-28057 PDF: SPF-28057
Date:
Thursday, July 17, 2014
Rev
B
Sheet
1
3
of
3
3-7
USB-KW24D512
5
ICAP Classification:
Drawing Title:
USB-KW24D512
1
JTAG / SWD CONNECTOR
1
POWER MANAGEMENT
USB-KW24D512
Figure 3-8. USB-KW24D512 Reference Board PCB Component Location (Top View)
Figure 3-9. USB-KW24D512 Reference Board PCB Test Points
Figure 3-10. USB-KW24D512 Reference Board PCB Layout (Top View)
USB-KW2x Hardware Reference Manual, Rev. 0.3
3-8
Freescale Semiconductor
USB-KW24D512
Figure 3-11. USB-KW24D512 Reference Board PCB Layout (Bottom View)
3.3.1
Bill of Materials
Table 3-2. Bill of Materials (Common parts for all frequency bands) (Sheet 1 of 3)
Item Qty Reference
Value
Description
Mfg. Name
Mfg. Part Number
1
1
ANT1
MEANDER_ PCB MEANDER ANTENNA
ANT_HORZ HORIZONTAL, NO PART ORDER
2
3
C1,C4,C26 5pF
CAP CER 5pF 50V 5% C0G 0402 MURATA
GJM1555C1H5R0CB0
1D
3
3
C2,C5,C24 1000pF
CAP CER 1000PF 50V 5% C0G
0402
MURATA
GRM1555C1H102JA0
1D
4
2
C3,C15
0.33UF
CAP CER 0.33UF 6.3V 10% X5R
0402
MURATA
GRM155R60J334KE0
1D
5
3
C6,C8,C9
0.1UF
CAP CER 0.1UF 16V 10% X7R
0402
KEMET
C0402C104K4RAC
6
1
C7 DNP
0.1UF
CAP CER 0.1UF 16V 10% X7R
0402
KEMET
C0402C104K4RAC
7
2
C10,C11
11pF
CAP CER 11pF 50V 5% C0G 0402 TDK
C1005C0G1H110J
8
2
C12,C16
33PF
CAP CER 33PF 50V 5% C0G 0402 VENKEL COMPANY
C0402C0G500-330JN
E
9
1
C17
1PF
CAP CER 1PF 50V 5% C0G 0402 MURATA
GRM1555C1H1R0CA
01B
10
2
C18,C19
10PF
CAP CER 10PF 50V 5% C0G 0402 AVX
04025A100JAT2A
11
1
C20
1.8pF
CAP CER 1.8PF 50V 0.25PF C0G MURATA
0402
GRM1555C1H1R8CA
01D
12
1
C21
1.0UF
CAP CER 1.0UF 10V 10% X5R
0402
CC0402KRX5R6BB10
5
YAGEO AMERICA
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
3-9
USB-KW24D512
Table 3-2. Bill of Materials (Common parts for all frequency bands) (Sheet 2 of 3)
Item Qty Reference
Value
Description
Mfg. Name
Mfg. Part Number
13
2
C25,C27
DNP
47PF
CAP CER 47PF 16V 5% C0G 0402 AVX
0402YA470JAT2A
14
1
C29
2.2UF
CAP CER 2.2UF 10V 10% X7R
0603
TAIYO YUDEN
LMK107B7225KA-T
15
1
D1
GREEN
LED GRN SGL 30MA SMT 0805
LITE ON
LTST-C171KGKT
16
2
D2,D3
BLUE
LED BLUE SGL 20MA SMT 0805
LITE ON
LTST-C171TBKT
17
1
J1
HDR 2X5
CONN,HEAD,2X5,STR,50/50
CON-2RH-10-50
SAMTEC
FTS-105-01-F-D
18
1
J4 DNP
MM8030-26 CON COAX SMT 1.9MM SP 40H
00B
AU
MURATA
MM8030-2610B
19
1
J5
USB_TYPE
_A
CON 1X4 USB_TYPE_A_MALE
RA SMT -- 178H AU
SAMTEC
USB-AM-S-S-B-SM1
20
1
L3
2.2nH
IND -- 2.2NH@500MHZ 220mA
4% 0402
MURATA
LQP15MN2N2B02
21
1
L4
60OHM
IND FER BEAD 60OHM@100MHZ MURATA
500MA -- 0603
BLM18PG600SN1D
22
1
L5
330 OHM
IND FER BEAD
330OHM@100MHZ 2.5A -- SMT
MPZ2012S331A
23
4
MH1,MH2,
MH3,MH4
MH_80mil
Rework Hole Non-Plated 80mil
Drill size 95mil Soldermask TH, NO
PART TO ORDER
24
1
RT1
MINISMDC
050F-2
FUSE PLYSW 0.5A 24V SMT
TYCO ELECTRONICS MINISMDC050F-2
25
1
R1
1.0M
RES MF 1.0M 1/10W 5% 0603
BOURNS
CR0603-JW-105ELF
26
5
R2,R3,R11, 0
R12
RES MF ZERO OHM 1/16W 5%
0402
ROHM
MCR01MZPJ000
27
1
R6
10K
RES MF 10K 1/10W 5% 0603
KOA SPEER
RK73B1JTTD103J
28
2
R7,R8
33
RES MF 33 OHM 1/10W 5% 0603 VISHAY
CRCW060333R0JNE
INTERTECHNOLOGY A
29
2
R9,R10
390
RES MF 390 OHM 1/16W 5% 0402 VISHAY
CRCW0402390RJNE
INTERTECHNOLOGY D
30
1
R13 DNP
10K
RES MF 10K 1/10W 5% 0603
31
1
R14
330
RES MF 330 OHM 1/16W 5% 0402 VISHAY
CRCW0402330RJNE
INTERTECHNOLOGY D
32
3
SH1,SH2
0
ZERO OHM CUT TRACE 0402
PADS; NO PART TO ORDER
33
2
SW1, SW2 SKQYAFE0
10
SW SPST MOM PB 50MA 12V
SMT
TDK
KOA SPEER
ALPS ELECTRIC
(USA) INC.
RK73B1JTTD103J
SKQYAFE010
USB-KW2x Hardware Reference Manual, Rev. 0.3
3-10
Freescale Semiconductor
USB-KW24D512
Table 3-2. Bill of Materials (Common parts for all frequency bands) (Sheet 3 of 3)
Item Qty Reference
34
18
35
Value
Description
Mfg. Name
Mfg. Part Number
TP1,TP2,TP3,
TP4,TP5,TP6,
TP7,TP8,TP9,
TP10,TP11,TP
12,TP13,TP14
,TP15,TP16,T
P17,TP18
TPAD_040
TEST POINT PAD 40MIL DIA SMT,
NO PART TO ORDER
1
TP19
TPAD_030
TEST POINT PAD 30MIL DIA SMT,
NO PART TO ORDER
36
1
TP28 DNP
TEST
POINT
WHITE
TEST POINT WHITE 40 MIL
DRILL 180 MIL TH 109L
37
1
U1
MKW24D51 IC MCU XCVR 2.4GHZ 64KB RAM Freescale
Semiconductor
2V
512KB FLASH - USB 1.8-3.6V
LGA63
MKW24D512VHA5
38
1
Y1
32MHZ
XTAL 32MHZ 9PF -- SMT
3.2X2.5MM
NDK
EXS00A-CS02368
39
1
Z1
2400MHz
50OHM
XFMR BALUN 2400 +/-100MHZ
SMT
MURATA
LDB212G4005C-001
40
1
C28
0.1UF
CAP CER 0.1UF 10V 10% X5R
0402
KEMET
C0402C104K8PAC
41
1
C13
0.47UF
CAP CER 0.47UF 6.3V 10% X5R
0402
MURATA
GRM155R60J474KE1
9D
42
1
C30
1000pF
CAP CER 1000PF 50V 5% C0G
0402
MURATA
GRM1555C1H102JA0
1D
COMPONENTS
CORPORATION
TP-105-01-09
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
3-11
USB-KW24D512
USB-KW2x Hardware Reference Manual, Rev. 0.3
3-12
Freescale Semiconductor
Chapter 4
PCB Manufacturing Specifications
This chapter provides the specifications used to manufacture the KW2x Development hardware printed
circuit board (PCB) described in this manual.
The KW2x Development hardware PCBs must comply with the following:
• The PCB must comply with Perfag1D/3C (http://www.perfag.dk/Uk/ukindex.htm)
• The PCB manufacturer’s logo is required
• The PCB production week and year code is required
— The manufacturer’s logo and week/year code must be stamped on the back of the PCB solder
mask
— The PCB manufacturer can not insert text on the PCB either in copper or in silkscreen without
written permission from Freescale Semiconductor, Inc.
• The required Underwriter’s Laboratory (UL) Flammability Rating
— The level is 94V-0 (http://www.ul.com/plastics/flame.html)
— The UL information must be stamped on the back of the PCB solder mask
•
•
4.1
NOTE
A complete set of design files is available for the KW2x Development
hardware at the Freescale web site (http:www.freescale.com/KW2x)
under the “Software and Tools” tab. This design or one of a number of
other reference designs should be used as a starting point for a custom
application.
The Freescale IEEE 802.15.4 / ZigBee Package and Hardware Layout
Considerations Reference Manual, (ZHDCRM) is also available at the
same web site to provide additional design guidance.
Single PCB Construction
This section describes individual PCB construction details.
•
•
•
The USB-KW24D512 PCB is four-layer, multi layer design
The PCBs contains no blind, buried, or micro vias
PCB data:
— USB-KW24D512 Size: Approximately 61.4 x 18.5mm (2.42 x 0.73 inches)
— USB-KW24D512 Final thickness (Cu/Cu): 1.57 mm (0.62 inches) +/- 10% (excluding solder
mask)
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
4-1
PCB Manufacturing Specifications
The following table defines some of the layers of the completed PCB. The artwork identification refers to
the name of the layer in commonly used terms.
Table 4-1. USB-KW24D512 Layer by Layer Overview
Layer
Artwork Identification
File Name
1
Silkscreen Top
SILK_TOP.art
2
Top Layer Metal
TOP.art
3
Ground Layer
GND.art
4
Power Layer
PWR.art
5
Bottom Layer Metal
BOTTOM.art
6
Silkscreen Bottom
SILK_BOTTOM.art
NOTE
The USB-KW24D512 contains high frequency 2.4 GHz RF circuitry. As a
result, RF component placement, line geometries and layout, and spacing to
the ground plane are critical parameters. As a result, BOARD STACKUP
GEOMETRY IS CRITICAL. Dielectric and copper thicknesses and spacing
must not be changed; follow the stackup (see Figure 4-1) information is
provided with the reference design.
Figure 4-1. USB-KW24D512 PCB Stackup Cross-Section (Four Layer)
•
•
4.2
Solder mask is required
Silk screen is required
Panelization
The panel size can be negotiated depending on production volume.
4.3
Materials
The PCB composite materials must meet the following requirements:
USB-KW2x Hardware Reference Manual, Rev. 0.3
4-2
Freescale Semiconductor
PCB Manufacturing Specifications
•
•
•
4.4
Laminate - The base laminate material (laminate) must be FR4. If the laminate material were
changed the RF electrical characteristics may change and degrade RF performance.
Copper Foil — Top and Bottom copper layers must be 1 oz. copper
— Interior layers must be 1oz. copper
Plating - All pad plating must be Hot Air Levelling (HAL)
Solder Mask
The solder mask must meet the following requirements:
• Solder mask type: Liquid Film Electra EMP110 or equivalent
• Solder mask thickness: 10 – 30 µm
4.5
Silk Screen
The silk screen must meet the following requirements:
• Silkscreen color: White
• Silkscreen must be applied after application of solder mask if solder mask is required
• The silkscreen ink must not extend into any plated-thru-holes
• The silk screen must be clipped back to the line of resistance
4.6
•
•
4.7
Electrical PCB Testing
All PCBs must be 100 percent tested for opens and shorts
Impedance Measurement - An impedance measurement report is not mandatory
Packaging
Packaging for the PCBs must be the following requirements:
• Finished PCBs must remain in panel
• Finished PCBs must be packed in plastic bags that do not contain silicones or sulphur materials.
These materials can degrade solderability.
4.8
Hole Specification/Tool Table
See the ncdrill-1-4.tap file included with the Gerber files and the FAB-28057.pdf file.
USB-KW2x Hardware Reference Manual, Rev. 0.3
Freescale Semiconductor
4-3
PCB Manufacturing Specifications
4.9
File Description
Files included with the download include Design, Gerber and PDF files.
Gerber files are RS-274x format. Not all files included with the Gerber files are for PCB manufacturing.
PDF files included are:
• FAB-28057.pdf — USB - Board fabrication drawing
• GRB-28057.zip — USB - Metal layers, solder mask, solder paste and silk screen
• SPF-28057.pdf — USB - Schematic
Design files are in Allegro format with OrCAD schematic capture.
USB-KW2x Hardware Reference Manual, Rev. 0.3
4-4
Freescale Semiconductor