U2510B All-Band AM/FM Receiver and Audio Amplifier Description The U2510B is an integrated bipolar one-chip AM/FM radio circuit. It contains an FM front end with preamplifier, FM IF and demodulator, a complete AM receiver, an AF amplifier and a mode switch for AM, FM and tape. This circuit is designed for clock radios and portable radio-cassette recorders. Features Superior FM strong signal behavior by using RF AGC DC mode control: AM, FM and tape Soft mute and HCC for decreasing interstation noise in FM mode Wide supply-voltage range and low quiescent current Excellent AFC performance (level controlled, both polarities available) Electronic volume control Level indicator (LED drive) for AM and FM Output stage for headphone and speaker drive High AF output power: 1 W Electronic AF bandwidth control (treble and high cut) Block Diagram FM RF tank FM osc. tank (Replaceable) IF BPE FM ant. VS 9 8 7 6 14 16 2 26 AFC FM RF BPE AGC AM ant. AM osc. tank 12 11 10 FM front end FM IF amp. AFC control FM AGC Power 3 amp. AM IF amp. and detect. AM front end IF AGC RF AGC Voltage stab. and mode control FM Tape IF AF preamp. Level indic. Volume AM/FM 24 4 Mute HCC 21 S2 23 AM AGC 15 AM 27 25 5 VRef FM discr. 28 13 VS 20 19 1 22 18 LED AFC mode VS Treble Vol 13912 Figure 1. Block diagram Rev. A3, 23-Feb-01 1 (15) U2510B Order Information Extended Type Number U2510B-M U2510B-M__T Package SDIP28 SDIP28 Pin Description Remarks VS < 6 V supply voltage Pin 5 Symbol AMOsc Mute 1 28 AF-GND 6 FM–AFC FM-discr 2 27 AFout 7 FMOsc CF 3 26 VS 8 9 VRef FMtank Vol ctrl in 4 25 Ripple in 10 AMtank 11 FM-AGC AMOsc 5 24 AFin FM-AFC 6 23 AM/FM detect 12 FMin FMOsc 7 22 VAGC/AFC 13 14 VRef 8 21 AFC switch 15 FE-GND AM/FM IFout Mode ctrl switch FMtank 9 20 IF-GND AMtank 10 19 LED drive FM-AGC 11 18 VTreble in FMin 12 17 FM-IFin FE-GND 13 16 AM-IFin AM/FM IFout 14 15 Mode ctrl switch 14812 16 17 18 19 AM-IFin FM-IFin VTreble in LED drive 20 21 IF-GND AFC switch 22 VAGC/AFC 23 AM/FM detect 24 AFin 25 Ripple in 26 27 28 VS AFout AF-GND Figure 2. Pinning Pin 1 Symbol Mute 2 FM-discr 3 CF 4 2 (15) Vol ctrl in Function Mute voltage output, time constant (C23), mute depth and threshold adjustable by load resistance (R3) FM discriminator filter connection, ceramic resonator or equivalent LC-circuit Audio negative feedback input. Blocking capacitor (C8) determines the audio amplifiers low-end cut-off frequency Input for volume control voltage Function AM oscillator tank circuit input, recommended load impedance approximately 2.5 k AFC diode connection, coupling capacitor (C19) determines the AFC characteristic (holding range and slope) FM oscillator tank circuit input, recommended load impedance approximately 3 k Regulated voltage output (2.4 V) FM RF tank circuit connection, recommended load impedance approximately 3 k AM RF tank circuit connection, recommended load impedance approximately 20 k FM AGC voltage output, time constant (C20). Loading this pin by a resistor (to GND) will increase the FM AGC threshold, grounding this pin will switch off the FM AGC function FM RF input (common-base preamplifier transistor), recommended (RF) source impedance approximately 100 FM front-end ground AM/FM IF output (collector output of the IF preamplifier) Mode control input: Pin | Function open | FM Ground | AM VS (R4 = 10 k) | Tape AM IF input, input impedance = 3.1 k FM IF input, input impedance = 330 Treble control voltage input Level indicator output (open-collector output, LED drive) IF ground AFC function control input: Pin | Function open | AFC off Ground | fOSC > fin VS | fOSC < fin AGC/AFC voltage, time constant adjust (C10), input impedance approximately 42 k AM/FM detector output, the load capacitor (C11) in conjunction with the detector output resistance (7.5 k) determines the (FM) deemphasis as well as the (modulation) frequency response of the AM detector Audio amplifier input, input resistance approximately 100 k coupling capacitor (C9) determines the low frequency response Ripple filter connection. Load capacitance (C12) determines the frequency response of the supply-voltage ripple rejection Supply voltage input Audio amplifier output Ground of the audio power stage Rev. A3, 23-Feb-01 U2510B Terminal Voltages Test circuit: Vin = 0 Voltage/V Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Symbol Mute voltage (R3 = 0) FM discriminator Negative feedback Volume control input (S4 = A) AM oscillator FM AFC FM oscillator VRef FM RF tank AM input FM AGC FM input Front end ground AM/FM IF output Mode control switch AM IF input FM IF input Treble control input (S5 = A) LED IF ground AFC switch (S3 = off) AGC (AM)/AFC (FM) Detector output AF input Ripple filter Supply voltage AF output AF ground Rev. A3, 23-Feb-01 V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20 V21 V22 V23 V24 V25 V26 V27 V28 VS = 3 V FM 1.6 1.0 1.2 2.4 – 1.9 2.4 2.4 2.4 – 0 1.4 – – 2.9 2.7 0 – 0 – – 0.7 2.4 2.4 AM – – 1.2 2.4 2.4 – – 2.4 – 2.4 – 0 1.2 1.5 1.5 1.5 2.7 3.0 1.2 0 0 1.2 1.2 1.2 1.5 2.7 3.0 1.2 0 TAPE – – 1.2 2.4 – – – 2.4 2.4 – – – – – 2.9 – – 2.4 AM – – 2.6 2.4 2.4 – – 2.4 – – – – – 5.9 0 0 – 2.4 VS = 6 V FM 1.6 1.0 2.6 2.4 – 1.9 2.4 2.4 2.4 2.4 0 1.4 – 5.7 – – 0.7 2.4 TAPE – – 2.6 2.4 – – – 2.4 – – – – – – 5.7 – – 2.4 0 1.2 – – 1.5 2.7 3.0 1.2 0 0 1.2 1.5 1.5 1.5 5.3 6.0 2.6 0 0 1.2 1.2 1.2 1.5 5.3 6.0 2.6 0 0 1.2 – – 1.5 5.3 6.0 2.6 0 3 (15) U2510B Absolute Maximum Ratings Parameters Supply voltage Power dissipation Ambient temperature range Symbol VS Ptot Tamb Value 13 900 –20 to +75 Unit V mW °C Electrical Characteristics VS = 6 V, Tamb = 25°C, test circuit (figure 16), unless otherwise specified Parameters Supply voltage range Oscillator stop voltage Operating temperature range Supply quiescent current Test Conditions / Pins Symbol VS VS T Min. 2.5 2.2 –20 Typ. Vi1 = Vi2 = V4 = 0; AM (S2 = AM) IS 4.0 FM (S2 = FM) IS 6.5 TAPE (S2 = Tape) IS 2.2 Regulated voltage Pin 8 VRef 2.4 Audio amplifier Vi3 (Pin 24), test point: Vo (Pin 27) f = 1 kHz AF measuring range: 30 Hz to 20 kHz, S2 = Tape, S4 = A, S5 = A Input resistance Pin 24 Rj 100 Closed loop voltage gain GVaf1 = 20 log (Vo/Vi3) Vi3 = 10 mV GVaf1 40 Output voltage Vi3 = 100 mV, S4 = B Vo 0.7 High–end cut-off frequency fc (–3 dB) fc 13 S5 = B fc 0.8 Supply-voltage rejection ratio SVRR = 20 log (Vhum/Vo) Vhum = 200 mV, fhum = 200 Hz, S4 = B SVRR 32 Noise voltage S4 = B, Vi3 = 0 Vn 300 AF output power THD = 10 %, RL = 8 VS = 4.5 V Po 225 VS = 6.0 V Po 400 420 VS = 9.0 V Po 1000 Distortion Po = 50 mW, RL = 8 d 0.6 FM section, Vi2 = 60 dBV, fi2 = 98 MHz, fm = 1 kHz, dev. = 22.5 kHz, fiIF = 10.7 MHz, AF measuring range: 300 Hz to 20 kHz, S2 = FM, S1 = A, S6 = B, test point: VD (Pin 23) FM front-end voltage gain GVFM = 20 log (ViIF / Vi2) S1 = B, Vi2 = 40 dbV GVFM 30 Recovered audio voltage Pin 23 VD af 85 Detector output resistance Pin 23 RDo 7.5 Detector output distortion dev. = 75 kHz THD 0.5 Vi2 = 60 dBV Vi2 = 105 dBV THD 0.8 * 4 (15) Max. 9* +75 Unit V V °C mA mA mA V k 3 1000 dB mV kHz kHz dB V mW mW mW % dB mV k % % U2510B-M__T: max. 6 V Rev. A3, 23-Feb-01 U2510B Electrical Characteristics (continued) VS = 6 V, Tamb = 25°C, test circuit (figure 16), unless otherwise specified Parameters AM rejection ratio RF sensitivity Limiting threshold (-3 dB) Mute voltage Mute depth AFC holding range Test Conditions / Pins m = 30% (S+N)/N = 26 dB (S+N)/N = 46 dB Test point: Mute Vi2 = 0 Vi2 = 60 dBV Referred to V0 at Vi2 = 0 S6 = A S6 = C fOSC > fin, S3 = A, S6 = A Vi2 10 dBV Vi2 = 20 dBV Vi2 = 80 dBV Symbol AMRR Vi2 Vi2 Vi2 Min. Max. Unit dB dBV dBV dBV Vmute Vmute 1.8 0.4 V V MD MD 26 20 dB dB no AFC 180 220 5.5 180 kHz kHz mA mV 25 dB 70 7.5 1 3 0 16 35 mV k % % dBV dBV dBV 100 3.1 5.5 160 dB k mA mV FHR FHR FHR LED current ILED Oscillator voltage eZload = 2.5 k Pin 7 VOSC AM section Vi1 = 60 dBV, fi1 = 1.6 MHz, fm = 1 kHz, m = 30%, fiIF = 455 kHz, AF measuring range: 300 Hz to 20 kHz, (S2 = AM, S1 = B, test point: VD) AM front end voltage gain GVAM = 20 log (ViIF/Vi1) GVAM Vi1 = 20 dBV, S1 = A Recovered audio voltage VD af1 Detector output resistance Pin 23 RDo Detector output distortion Vi1 = 60 dBV THD Vi1 = 105 dBV THD RF sensitivity (S+N)/N= 10 dB Vi1 (S+N)/N= 26 dB Vi1 Vi1 (S+N)/N= 46 dB AGC figure of merit referred Vi1 = 105 dBV, voltage to VD af drop (VD af) = –10 dB FOM IF input resistance Pin 16 Zi LED current ILED Oscillator voltage Pin 5 VOSC Rev. A3, 23-Feb-01 Typ. 25 9 22 3 5 (15) U2510B 10 10000 Tamb=25°C FM 8 Po ( mW ) IS ( mA ) 1000 6 AM 4 RL=4 100 Tape f=1kHz d=10% Tamb=25°C 8 2 16 32 0 10 2 4 6 8 10 12 VS ( V ) 9510396 0 50 10 VS ( V ) 9510399 Figure 3. Quiescent current Figure 6. AF section: Max. output power 40 50 without treble control 40 f=200Hz Po ( mW ) VU ( dB ) 32 30 with treble control 20 f=100Hz 24 Vi=5mV VS=6V RL=8 Tamb=25°C 10 0 0.01 Vhum=200mV VS=6V RL=8 Tamb=25°C 16 0.1 1 10 100 f ( kHz ) 95 10397 2 4 6 12 Figure 7. AF section: Supply-voltage rejection ratio 10 2.0 f=1kHz Tamb=25°C VS=6V Tamb=25°C 1.6 Vo ( dBV ) 8 d(%) 10 VS ( V ) 95 10400 Figure 4. AF section 8 6 VS=3V RL=32 VS=6V RL=8 VS=9V RL=8 4 R3=∞ 1.2 100k 0.8 68k 2 0.4 0 1 95 10398 10 100 1000 Po ( mW ) Figure 5. AF section: Distortion 6 (15) 0 –20 10000 95 10403 0 20 40 60 80 100 120 Vi ( dBV ) Figure 8. FM section: Mute voltage Rev. A3, 23-Feb-01 U2510B 0 6 AM S+N(m=80%) –40 VS=6V fi1=1.6MHz fAF=1kHz Tamb=25°C N –60 FM 4 I LED ( mA ) VD ( dBV ) S+N(m=30%) 3 2 –80 VS=6V Tamb=25°C 1 d(m=80%) –100 –20 d(m=30%) 0 0 20 40 60 80 100 120 Vi ( dBV ) 95 10404 0 20 40 60 80 100 120 Vi ( dBV ) 95 10407 Figure 9. AM section: Demodulator output level Figure 11. AM/FM level indicator current 0 2.0 VS=6V Vi3=10mV fAF=1MHz fAF=10kHz Tamb=25°C 1.2 VAGC ( V ) –20 VO ( dBV ) ILED 5 –20 Treble Voltage V8 –40 –60 0.8 VS=6V fi1=1.6MHz Tamb=25°C 0.4 Treble Voltage = 0 –80 0 0 0.5 95 10406 1 1.5 2 2.5 V4 ( V ) Figure 10. Volume control range characteristics Rev. A3, 23-Feb-01 20 95 10408 0 20 40 60 80 100 120 Vi ( dBV ) Figure 12. AM section: AGC voltage (at Pin 22) 7 (15) U2510B 0 S+N(f=75kHz) VD ( dBV ) –20 VS = 6 V fi2 = 98 MHz fAF = 1 kHz Tamb = 25°C S+N(f=22.5kHz) –40 AM(m=30%) –60 –80 d(f=75kHz) N d(f=22.5kHz) –100 –20 0 20 40 100 80 60 120 Vi ( dBV ) 95 10401 Figure 13. FM section: Demodulator output level 0 R3=0 68k S+N –20 VS = 6 V RL = 8 Po = 50 mW at Vi2 = 60 dBV fi2 = 98 MHz fAF = 1 kHz f = 22.5 kHz mAM = 30% Tamb = 25°C AM 100k Vo ( dBV ) ∞ –40 –60 N –80 d –100 –20 0 20 40 60 80 100 120 Vi ( dBV ) 95 10402 Figure 14. FM section: Audio output level 0 S+N VO ( dBV ) –20 –40 N Po = 50 mW at Vi1 = 60 dBV RL = 8 fi1 = 98 MHz fAF = 1 kHz m = 80% Tamb = 25°C d –60 –80 –100 –20 95 10405 0 20 40 60 80 100 120 Vi ( dBV ) Figure 15. AM section: Audio output level 8 (15) Rev. A3, 23-Feb-01 U2510B Test Circuit R5 150 Ω R6 Vi1 (50 Ω) Vi2 (50 Ω) C24 C2 LA 100 Ω 100 nF C25 R C3 43 pF 22 pF 150 µH C7 75 Ω 10 nF 22 pF C19 C25 5.6 pF 100 pF C8 4.7 µF 22 nF T1 14 13 12 11 10 9 8 7 B A S5 T4 C6 C20 AM IFT B A S4 R4 2.2 kΩ 4.7 µF 22 nF 50 Ω C5 18 pF L1 L2 7 R8 T2 C4 R3 150 kΩ C23 68 nF C S6 C24 18 pF 6 5 4 3 2 1 23 24 25 26 27 28 B A Vmute 455 kHz CF1 U2510B 15 B A S1 16 B A 17 19 18 CF2 C22 10.7 MHz R1 Tape ViIF R9 3 kΩ S2 FM C21 AM 20 D1 21 A 10 nF off LED 22 C9 S3 10 nF B C15 390 Ω R2 220 µF C14 10 kΩ C10 C11 100 nF 10 µF 10 nF C12 C13 10 µF 470 µF 10 nF ILED VD Vi3 VS RL 8 Ω/ 2W Vo GND 13913 Figure 16. Test circuit Application General The U2510B is a bipolar monolithic IC for use in radio sets, for example, headphone receivers, radio recorders and clock radios. The IC contains all AM, FM, AF and switching function blocks necessary to construct these kinds of radio receivers using only few components around the IC. In the design, special efforts were made to get good performance for all AM bands (short and long wave). The implementation of enhanced functions (options) makes it possible to improve the radio’s performance and to produce radios with interesting features. In this case few (external) parts have to be changed or added. By using all or some of the options offered by the U2510B different types or classes of radios can be designed to the customer ’s requirements with the same IC. Rev. A3, 23-Feb-01 One of the general advantages of using the U2510B is the fact that all receiver functions (including the options) are integrated and tested on a system level. Therefore, two additional cost-savings are achieved by: 1. Shorter development time through less technical problems and 2. Higher reproductivity and low reject level in the set production line. Another advantage, due to the technology of the U2510B, is the wide operating voltage range, especially the upper limit (13 V). This feature allows the use of soft power supply for line powered radios which can also reduce the set’s total cost. 9 (15) U2510B Circuit Example Figure 17 shows a circuit diagram for low end AM/AF radios using the U2510B. Figure 18 shows a circuit diagram of AM/AF radio for higher class designs using all possible options of the U2510B. The layout of the PC board, shown in figure 19, is suitable for both the circuit example shown in figure 17 and the circuit example shown in figure 18. The associated coil, varicon and filter specifications are listed in the table: COIL DATA and SPECIAL COMPONENT PARTS. The circuit diagram (figure 18), has the following options compared to the circuit diagram (figure 17) (the additional parts, which have to be provided, are listed in parentheses): a) Soft mute and high cut control in FM mode (1 cap.) b) Electronic treble control in AM, FM and TAPE mode (1 pot.) c) On-chip mode control for TAPE application d) RF AGC in FM mode (1 capacitor) e) AFC, adjustable to the correct polarity and slope (1 cap.) f) Tuning indication using LED as an indicator (1 LED, 1 cap.) Option a) reduces the interstation noise by the two functions: soft mute and HCC. Both are controlled by the mute voltage (Pin 1). The soft mute reduces the loudness only, while the HCC reduces the high-end audio cut-off frequency of the audio preamplifier, when the signal level falls below a given threshold. This signal level threshold as well as the mute depth can be reduced by adding a resistor (R3) or by increasing the FM front–end gain. Option b) allows the treble control for all operating modes without the need of an additional capacitor. This concept leads to a smooth and correct treble control behavior which is an improvement compared to the controlled RC network normally used. Option c) is very useful for application in radio cassette-recorders, for instance. In TAPE mode, the AM/FM receiver blocks are completely switched off and the signal from the tape recorder can be fed to the audio amplifier ’s input directly. This saves quiescent current and makes the TAPE switching easy. However, to minimize switching noise by the mode switch, the following switch sequence should be chosen: AM, FM, TAPE. Option d) improves the strong signal behavior by protecting the FM mixer against overload. This is provided by the integrated broad-band-width RF AGC. If necessary, the AGC threshold can be decreased by a resistor, loading Pin 11 to GND (not shown). 10 (15) Option e) improves the tuning behavior substantially. The special design of the on-chip AFC function means that common disadvantages such as asymmetrical slope, (chip-) temperature effects and unlimited holding range are avoided. As mentioned in the “Pinning Description Table”, the AFC slope has to be inverted when the local oscillator (LO) frequency has to be below the receiving frequency. This can be achieved by connecting Pin 21 to the potential of Pin 8. In addition to the options described above, the following proposals are implemented in the circuit diagram (figure 18), too: An FM IFT is applied. This improves the channel selectivity and minimizes substantially the spurious responses caused by the FM ceramic filter (CF2). With the choice of the winding ratio of this IFT, the FM front end gain can be matched to other values if necessary. In the FM RF input section, the low cost antenna filter (L5, C15) is replaced by a special band pass filter (PFWE8). Such a BPF protects the FM front end against the out-off-band interference signals (TV channels, etc.) which could disturb the FM reception. Design Hints The value of the power supply blocking capacitor C13 should not be below 470 F. In addition, this capacitor should be placed near Pin 26. This will help to avoid unacceptable noise generated by noise-radiation from the audio amplifier via the bar-antenna. In designs, where the supply voltage goes below 2.5 V, the value of the blocking capacitor (C7) should be chosen as 47 F or even higher. To achieve a high rejection of short wave reception in medium wave operation, the LO amplitude at Pin 5 should not exceed approximately 200 mV. This LO amplitude depends on the LO transformer’s Q and its turns ratio. For the LO transformer type described in the “Coil Data Table”, a resistor R4 (2.2 k for example) in parallel to the secondary side of the AM LO transformer T2 is recommended. To minimize feedback effects in the RF/IF part in FM mode, the capacitor C6 should be placed as near to Pins 8 and 20 as possible. As shown in the application circuit diagrams (figures 17 and 18), in FM mode ceramic filter devices are used for channel selection (CF2) while for FM, demodulation in LC-discriminator circuit (T4, C24, C25) is used instead of a ceramic discriminator device. Such an LC discriminator circuit can be easily matched to the FM IF selectivity block by its alignment. The zerocrossing of the discriminator can be detected at the demodulator output (Pin 23). The zero-crossing voltage is equal to half of the regulated voltage at Pin 8. Rev. A3, 23-Feb-01 U2510B The alignment of the LC-discriminator circuit should be done with little or no effect on the AFC function. This can be realized by: – switching Pin 21 to open-circuit – connecting Pin 1 to a voltage source of 2 V – using a low signal level for alignment. In general, ceramic discriminator devices can be used, too. In this case, the effect of unavoidable spreads in the frequency characteristics of these case ceramic devices in conjunction with the IC characteristic has to be considered. For example, mismatches of the characteristics between selectivity block and FM discriminator will lead to an increased signal-to-noise ratio at low signal level as well as to a higher demodulation distortion level or to an asymmetrical AFC. Application Circuits Antenna FM AM L3 C16 33 pF C18 C3 C2 2 pF T2 C4 C5 27 pF 22 pF Volume 6 pF L1 L2 P1 50 kΩ C17 33 pF 33 pF L4 C7 T4 C6 C25 100 pF 4.7 µF 22 nF C24 18 pF C8 4.7 µF AM IFT T1 13 14 12 11 10 9 8 7 6 5 4 3 2 1 23 24 25 26 27 28 455 kHz CF1 U2510B 15 16 17 18 19 20 21 22 CF2 C9 10.7 MHz R1 390 Ω 10 nF 100 nF C14 S2 C10 C11 4.7 µF 10 nF C12 C15 220 µF S1 VS Z=8Ω C13 AM FM 4.7 µF 470 µF 13915 Figure 17. Application circuit (low cost) Rev. A3, 23-Feb-01 11 (15) U2510B Antenna FM AM L3 C3 C2 2 pF Volume T2 C4 27 pF 22 pF P1 50 kΩ 6 pF L1 L2 R4 2.2 kΩ BPF 1 Treble C5 T4 C25 100 pF C6 C7 C23 4.7 µF 22 nF C20 22 pF AM IFT T1 14 13 12 11 C8 4.7 µF C19 5.6 pF 10 9 P2 50 kΩ 8 7 (R3) 68 nF C24 18 pF 6 5 4 3 2 1 23 24 25 26 27 28 Mute Adj. 455 kHz CF1 U2510B AM IFT 15 16 T3 17 19 18 CF2 20 21 22 C22 C9 10.7 MHz 100 pF D1 10 nF LED 22 nF 100 nF R2 Tape FM 10 kΩ S2 AM C21 C14 C10 C11 10 µF 10 nF C12 C15 220 µF S1 VS C13 4.7 µF 470 µF 10 nF IN Tape 13914 Figure 18. Application circuit (upgraded) R2 only if VS > 8 V Figure 19. PC-board 12 (15) Rev. A3, 23-Feb-01 U2510B Coil Data and Special Component Part Part Stage T1 AM IFT 180 pF 1 to 3 90 1 to 3 0.07 1 to 2 111 Wire diameter/mm Terminal No. Number of turns 0.07 2 to 3 35 T2 AM OSC 270 H 1 to 3 125 1 to 3 0.06 1 to 3 107 0.06 4 to 6 29 T3 FM IFT (optional) 100 pF 1 to 3 0.09 2 to 3 7 T4 FM discriminator 100 pF 1 to 3 L1 FM RF air coil 4 mm diam. FM OSC air coil 4 mm diam. FM antenna air coil 4 mm diam. 0.09 1 to 2 3 0.09 1 to 3 10 0.62 L2 L4 L3 BPF1 CF1 L or C0 between Q0 between 4.75 (optional) Variable capacitor L: 630 H total turns : 96 tap: 19 PFWE8 (88 to 108 MHz) Soshin Electric Co. SFU-455B Murata BFCFL-455 Toko SFE10.7MA5 Murata CFSK 107M1 Toko CDA10.7MC1 Murata HD22124 AM/FM Toko 4 mm 3 mm 80 mm 4 18 mm 2 4 0.09 4 to 6 2 7MC-7789N Toko 21K7-H5 Mitsumi 7TRS-8441 Toko L-5K7-H5 Mitsumi mat.: 7P A119 AC Toko mat.: 7P A119 AC Toko 3.75 0.62 CF2 3 0.07 4 to 6 7 3.75 0.62 AM bar antenna (optional) CF3 C1 Type Manufacturer 6 C1 Coil, bottom view Air coil Pin 10 AM bar antenna Pin 8 13931 Figure 20. Rev. A3, 23-Feb-01 13 (15) U2510B Package Information Package SDIP28 Dimensions in mm 27.5 27.1 10.26 10.06 4.8 4.2 0.9 3.3 8.7 8.5 0.35 0.25 0.53 0.43 23.114 1 14 (15) 12.2 11.0 1.778 technical drawings according to DIN specifications 13044 Rev. A3, 23-Feb-01 U2510B Ozone Depleting Substances Policy Statement It is the policy of Atmel Germany GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Atmel Germany GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Atmel Germany GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Atmel Wireless & Microcontrollers products for any unintended or unauthorized application, the buyer shall indemnify Atmel Wireless & Microcontrollers against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Data sheets can also be retrieved from the Internet: http://www.atmel–wm.com Atmel Germany GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 (0)7131 67 2594, Fax number: 49 (0)7131 67 2423 Rev. A3, 23-Feb-01 15 (15)