PHILIPS TEA1066T

INTEGRATED CIRCUITS
DATA SHEET
TEA1066T
Versatile telephone transmission
circuit with dialler interface
Product specification
Supersedes data of September 1990
File under Integrated Circuits, IC03
1996 Apr 04
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
• Receiving amplifier for magnetic, dynamic or
piezoelectric earpieces
FEATURES
• Voltage regulator with adjustable static resistance
• Large gain setting range on microphone and earpiece
amplifiers
• Provides supply for external circuitry
• Symmetrical low-impedance inputs for dynamic and
magnetic microphones
• Line loss compensation facility, line current dependent
(microphone and earpiece amplifiers)
• Symmetrical high-impedance inputs for piezoelectric
microphone
• Gain control adaptable to exchange supply
• DC line voltage adjustment facility.
• Asymmetrical high-impedance input for electret
microphone
GENERAL DESCRIPTION
• Dual-tone multi-frequency (DTMF) signal input with
confidence tone
The TEA1066T is a bipolar integrated circuit that performs
all speech and line interface functions required in fully
electronic telephone sets. The circuit performs electronic
switching between dialling and speech.
• Mute input for pulse or DTMF dialling
• Power down input for pulse dial or register recall
QUICK REFERENCE DATA
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
VLN
line voltage
Iline = 15 mA
4.25
4.45
4.65
V
Iline
line current
normal operation
10
−
140
mA
ICC
internal supply current
power down input LOW
−
0.96
1.3
mA
power down input HIGH
−
55
82
µA
Iline = 15 mA; MUTE
input HIGH; Ip = 1.2 mA
2.8
3.05
−
V
Iline = 15 mA; MUTE
input HIGH; Ip = 1.7 mA
2.5
−
−
V
low impedance inputs (pins 7 and 9)
44
−
60
dB
high impedance inputs (pins 8 and 10)
30
−
46
dB
receiving amplifier
17
−
39
dB
−25
−
+75
°C
dB
VCC
Gv
Tamb
supply voltage for peripherals
voltage gain range for microphone amplifier
operating ambient temperature
Line loss compensation
∆Gv
gain control
5.5
5.9
6.3
Vexch
exchange supply voltage
24
−
60
V
Rexch
exchange feeding bridge resistance
400
−
1000
Ω
ORDERING INFORMATION
TYPE
NUMBER
TEA1066T
1996 Apr 04
PACKAGE
NAME
SO20
DESCRIPTION
plastic small outline package; 20 leads; body width 7.5 mm
2
VERSION
SOT163-1
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
BLOCK DIAGRAM
VCC
handbook, full pagewidth
LN
17
IR
1
13
6
5
4
TEA1066T
MICL+
MICH+
MICH−
MICL−
DTMF
MUTE
PD
QR+
QR−
9
10
2
dB
8
GAS1
7
15
3
dB
16
14
SUPPLY AND
REFERENCE
AGC
CIRCUIT
CURRENT
REFERENCE
12
VEE
18
REG
19
AGC
11
STAB
The blocks marked ‘dB’ are attenuators.
Fig.1 Block diagram.
1996 Apr 04
GAR
3
20
MEA009 - 1
SLPE
GAS2
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
PINNING
SYMBOL
PIN
DESCRIPTION
LN
1
positive line terminal
GAS1
2
gain adjustment transmitting
amplifier
GAS2
3
gain adjustment transmitting
amplifier
QR−
4
inverting output receiving amplifier
QR+
5
non-inverting output receiving
amplifier
handbook, halfpage
LN
1
20 SLPE
GAR
6
gain adjustment receiving amplifier
GAS1
2
19 AGC
MICL−
7
inverting microphone input, low
impedance
GAS2
3
18 REG
QR−
4
MICH−
8
inverting microphone input, high
impedance
17 VCC
TEA1066T
MICL+
9
non-inverting microphone input, low
impedance
MICH+
10
non-inverting microphone input,
high impedance
MICH− 8
STAB
11
current stabilizer
MICL+
VEE
12
negative line terminal
MICH+ 10
IR
13
receiving amplifier input
PD
14
power-down input
DTMF
15
dual-tone multi-frequency input
MUTE
16
mute input
VCC
17
supply voltage decoupling
REG
18
voltage regulator decoupling
AGC
19
automatic gain control input
SLPE
20
slope (DC resistance) adjustment
GAR
6
15 DTMF
MICL−
7
14 PD
13 IR
12 VEE
9
11 STAB
MBH120
Fig.2 Pin configuration.
FUNCTIONAL DESCRIPTION
The DC current flowing into the set is determined by the
exchange supply voltage (Vexch), the feeding bridge
resistance (Rexch), the DC resistance of the telephone line
(Rline) and the DC voltage on the subscriber set
(see Fig.7).
Supplies: VCC, LN, SLPE, REG and STAB
Power for the TEA1066T and its peripheral circuits is
usually obtained from the telephone line. The TEA1066T
develops its own supply voltage at VCC and regulates its
voltage drop. The supply voltage VCC may also be used to
supply external peripheral circuits, e.g. dialling and control
circuits.
If the line current Iline exceeds the current ICC + 0.5 mA
required by the circuit itself (approximately 1 mA) plus the
current Ip required by the peripheral circuits connected to
VCC, then the voltage regulator diverts the excess current
via LN.
The supply has to be decoupled by connecting a
smoothing capacitor between VCC and VEE; the internal
voltage regulator has to be decoupled by a capacitor from
REG to VEE. An internal current stabilizer is set by a
resistor of 3.6 kΩ between STAB and VEE.
1996 Apr 04
16 MUTE
QR+ 5
4
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
The voltage regulator adjusts the average voltage on
LN to:
TEA1066T
and > 3 V, this being the minimum supply voltage for most
CMOS circuits, including voltage drop for an enable diode.
If MUTE is LOW, the available current is further reduced
when the receiving amplifier is driven.
VLN = Vref + ISLPE × R9
or
VLN = Vref + (Iline − ICC − 0.5 × 10−3A − Ip) × R9
Microphone inputs MICL+, MICH+, MICL− and MICH−
and amplification adjustment connections GAS1 and
GAS2
where Vref is an internally generated temperature
compensated reference voltage of 4.2 V and R9 is an
external resistor connected between SLPE and VEE.
The TEA1066T has symmetrical microphone inputs.
The MICL+ and MICL− inputs are intended for
low-sensitivity, low-impedance dynamic or magnetic
microphones. The input impedance is 8.2 kΩ (2 × 4.1 kΩ)
and its voltage gain is typically 52 dB. The MICH+ and
MICH− inputs are intended for a piezoelectric microphone
or an electret microphone with a built-in FET source
follower. Its input impedance is 40.8 kΩ (2 × 20.4 kΩ) and
its voltage gain is typical 38 dB.
The preferred value for R9 is 20 Ω. Changing the value of
R9 will also affect microphone gain, DTMF gain, gain
control characteristics, side-tone level and the maximum
output swing on LN.
Under normal conditions, when ISLPE >> ICC + 0.5 mA + Ip,
the static behaviour of the circuit is that of a 4.2 V regulator
diode with an internal resistance equal to that of R9. In the
audio frequency range, the dynamic impedance is largely
determined by R1 (see Fig.3).
The arrangements with the microphone types mentioned
are shown in Fig.9.
The gain of the microphone amplifier in both types can be
adjusted over a range of ±8 dB to suit the sensitivity of the
transducer used. The gain is proportional to external
resistor R7 connected between GAS1 and GAS2.
LN
handbook, halfpage
L eq
V ref
R9
20 Ω
V EE
Rp
R1
REG
VCC
C3
4.7 µF
An external capacitor C6 of 100 pF between GAS1 and
SLPE is required to ensure stability. A larger value may be
chosen to obtain a first-order low-pass filter. The cut-off
frequency corresponds with the time constant R7 × C6.
Mute input MUTE
C1
100 µF
A HIGH level at MUTE enables the DTMF input and
inhibits the microphone inputs and the receiving amplifier;
a LOW level or an open circuit has the reverse effect.
Switching the mute input will cause negligible clicks at the
earpiece outputs and on the line.
MBA454
Rp = 17.5 kΩ
Leq = C3 × R9 × Rp
Dual-tone multi frequency input DTMF
Fig.3 Equivalent impedance circuit.
When the DTMF input is enabled, dialling tones may be
sent onto the line. The voltage gain from DTMF to LN is
typically 25.5 dB and varies with R7 in the same way as
the gain of the microphone amplifier. The signalling tones
can be heard in the earpiece at a low level (confidence
tone).
The internal reference voltage can be adjusted by means
of an external resistor RVA. This resistor, connected
between LN and REG (pins 1 and 18), will decrease the
internal reference voltage; when connected between REG
and SLPE (pins 18 and 20) it will increase the internal
reference voltage.
Receiving amplifier: IR, QR+, QR− and GAR
The receiving amplifier has one input IR and two
complementary outputs, a non-inverting output QR+ and
an inverting output QR−.
Current Ip, available from VCC for supplying peripheral
circuits, depends on external components and on the line
current. Figure 8 shows this current for VCC > 2.2 V
1996 Apr 04
5
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
These outputs may be used for single-ended or for
differential drive, depending on the sensitivity and type of
earpiece used (see Fig.10). Gain from IR to QR+ is
typically 25 dB. This will be sufficient for low-impedance
magnetic or dynamic earpieces, which are suited for
single-ended drive. By using both outputs (differential
drive), the gain is increased by 6 dB and differential drive
becomes possible. This feature can be used when the
earpiece impedance exceeds 450 Ω (high-impedance
dynamic, magnetic or piezoelectric earpieces).
TEA1066T
bridged by the charge in the smoothing capacitor C1.
The requirements on this capacitor are relaxed by applying
a HIGH level to the PD input during the time of the loop
break, which reduces the supply current from typically
1 mA to typically 55 µA.
A HIGH level at PD further disconnects the capacitor at
REG, with the effect that the voltage stabilizer will have no
switch-on delay after line interruptions. This results in no
contribution of the IC to the current waveform during pulse
dialling or register recall. When this facility is not required
PD may be left open.
The output voltage of the receiving amplifier is specified for
continuous-wave drive. The maximum output voltage will
be higher under speech conditions, where the ratio of peak
to RMS value is higher.
Side-tone suppression
Suppression of the transmitted signal in the earpiece is
obtained by the anti-side-tone network consisting of
R1//Zline, R2, R3, R8, R9 and Zbal (see Fig.14). Maximum
compensation is obtained when the following conditions
are fulfilled:
R9 × R2 = R1 ( R3 + [ R8//Z bal ] )
(1)
The receiving amplifier gain can be adjusted over a range
of ±8 dB to suit the sensitivity of the transducer used.
The gain is set by the external resistor R4 connected
between GAR and QR+.
Two external capacitors, C4 = 100 pF and
C7 = 10 × C4 = 1 nF, are necessary to ensure stability.
A larger value of C4 may be chosen to obtain a first-order,
low-pass filter. The ‘cut-off’ frequency corresponds with
the time constant R4 × C4.
Z bal ⁄ ( Z bal + R8 ) = Z line ⁄ ( Z line + R1 )
(2)
If fixed values are chosen for R1, R2, R3, and R9, then
condition (1) will always be fulfilled, provided that
R8//Zbal < R3. To obtain optimum side-tone
suppression, condition (2) has to be fulfilled, resulting in:
Automatic gain control input AGC
Automatic line loss compensation is obtained by
connecting a resistor R6 between AGC and VEE. This
automatic gain control varies the microphone amplifier
gain and the receiving amplifier gain in accordance with
the DC line current.
Zbal = (R8/R1) Zline = k × Zline, where k is a scale factor:
k = (R8/R1).
The control range is 6 dB. This corresponds with a line
length of 5 km for a 0.5 mm diameter copper twisted-pair
cable with a DC resistance of 176 Ω/km and an average
attenuation of 1.2 dB/km.
1. Compatibility with a standard capacitor from the E6 or
E12 range for Zbal
Scale factor k (dependent on the value of R8) must be
chosen to meet the following criteria:
2. Zbal//R8 << R3
3. Zbal + R8 >> R9.
Resistor R6 should be chosen in accordance with the
exchange supply voltage and its feeding bridge resistance
(see Fig.11 and Table 1). Different values of R6 give the
same ratio of line currents for start and end of the control
range.
In practice, Zline varies greatly with line length and cable
type; consequently, an average value has to be chosen for
Zbal. The suppression further depends on the accuracy
with which Zbal/k equals the average line impedance.
Example: The balanced line impedance Zbal at which
the optimum suppression is preset can be calculated by:
If automatic line loss compensation is not required, AGC
may be left open. The amplifiers then all give their
maximum gain as specified.
Assume Zline = 210 Ω + (1265 Ω/140 nF), representing a
5 km line of 0.5 mm diameter, copper, twisted-pair cable
matched to 600 Ω (176 Ω/km; 38 nF/km). When k = 0.64,
then R8 = 390 Ω; Zbal = 130 Ω + (820 Ω//220 nF).
Power-down input PD
During pulse dialling or register recall (timed loop break)
the telephone line is interrupted, as a consequence it
provides no supply for the transmission circuit and the
peripherals connected to VCC. These gaps have to be
1996 Apr 04
The anti-side-tone network for the TEA1060 family shown
in Fig.4 attenuates the signal received from the line by
32 dB before it enters the receiving amplifier.
6
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
The attenuation is almost constant over the whole audio
frequency range. Figure 5 shows a conventional
Wheatstone bridge anti-side-tone circuit that can be used
as an alternative. Both bridge types can be used with
either resistive or complex set impedances.
TEA1066T
with 32 dB. The attenuation is nearly flat over the
audio-frequency range.
Instead of the previously-described special TEA1066
bridge, the conventional Wheatstone bridge configuration
can be used as an alternative anti-side-tone circuit. Both
bridge types can be used with either a resistive set
impedance or a complex set impedance.
The anti-side-tone network as used in the standard
application (see Fig.13) attenuates the signal from the line
LN
handbook, full pagewidth
R1
Zline
R2
IR
im
VEE
Rt
R3
R9
R8
Zbal
SLPE
MSA500 - 1
Fig.4 Equivalent circuit of TEA1060 family anti-side-tone bridge.
LN
handbook, full pagewidth
Zbal
R1
Zline
IR
im
VEE
Rt
R9
R8
RA
SLPE
MSA501 - 1
Fig.5 Equivalent circuit of an anti-side-tone network in a Wheatstone bridge configuration.
1996 Apr 04
7
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
VLN
positive continuous line voltage
−
12
V
VLN(R)
repetitive line voltage during switch-on or
line interruption
−
13.2
V
VLN(RM)
repetitive peak line voltage for a 1 ms pulse R9 = 20 Ω;
per 5 s
R10 = 13 Ω; (Fig.10)
−
28
V
Iline
line current
−
140
mA
Vn
voltage on any other pin
VEE − 0.7
VCC + 0.7
V
R9 = 20 Ω; note 1
Ptot
total power dissipation
−
555
mW
Tstg
IC storage temperature
R9 = 20 Ω; note 2
−40
+125
°C
Tamb
operating ambient temperature
−25
+75
°C
Tj
junction temperature
−
125
°C
Notes
1. Mostly dependent on the maximum required Tamb and on the voltage between LN and SLPE (see Fig.6).
2. Calculated for the maximum ambient temperature specified, Tamb = 75 °C and a maximum junction temperature of
125 °C.
THERMAL CHARACTERISTICS
SYMBOL
Rth j-a
1996 Apr 04
PARAMETER
VALUE
UNIT
thermal resistance from junction to ambient in free air mounted on glass epoxy
board 41 × 19 × 1.5 mm
90
K/W
8
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
MBH125
150
ILN
(mA)
130
handbook, halfpage
110
90
(1)
(2)
70
(3)
(4)
50
30
2
(1)
(2)
(3)
(4)
4
6
8
10
12
VLN − VSLPE (V)
Tamb = 45 °C; Ptot = 888 mW.
Tamb = 55 °C; Ptot = 777 mW.
Tamb = 65 °C; Ptot = 666 mW.
Tamb = 75 °C; Ptot = 555 mW.
Fig.6 Safe operating area.
CHARACTERISTICS
Iline = 10 to 100 mA; VEE = 0 V; f = 800 Hz; R9 = 20 Ω; Tamb = 25 °C; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supplies: LN and VCC (pins 1 and 17)
VLN
voltage drop over circuit between
LN and VEE
Iline = 5 mA
3.95
4.25
4.55
V
Iline = 15 mA
4.25
4.45
4.65
V
Iline = 100 mA
5.40
6.10
6.70
V
Iline = 140 mA
−
−
7.50
V
∆VLN/∆T
voltage drop variation with
temperature
Iline = 15 mA
−4
−2
0
mV/K
VLN
voltage drop over circuit between
LN and VEE with external resistor
RVA
Iline = 15 mA;
RVA = R1-18 = 68 kΩ
3.50
3.80
4.05
V
Iline = 15 mA;
RVA = R18-20 = 39 kΩ
4.70
5
5.30
V
supply current
PD = LOW; VCC = 2.8 V
−
0.96
1.30
mA
PD = HIGH; VCC = 2.8 V
−
55
82
µA
Iline = 15 mA; MUTE = HIGH;
Ip = 0 mA
3.50
3.75
−
V
Iline = 15 mA; MUTE = HIGH;
Ip = 1.2 mA
2.80
3.05
−
V
ICC
VCC
1996 Apr 04
supply voltage available for
peripheral circuits
9
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
SYMBOL
PARAMETER
TEA1066T
CONDITIONS
MIN.
TYP.
MAX.
UNIT
4.9
kΩ
Microphone inputs MICL+ and MICL−; MICH+ and MICH−
Zi
input impedance
MICL+ (pin 9); MICL− (pin 7)
3.3
MICH+ (pin 10); MICH− (pin 8)
CMRR
common mode rejection ratio
Gv
voltage gain
4.1
16.5
20.4
24.5
kΩ
−
82
−
dB
51
52
53
dB
Iline = 15 mA; R7 = 68 Ω
MICL+/MICL− to LN
37
38
39
dB
∆Gvf
gain variation with frequency at
f = 300 Hz and 3400 Hz
MICH+/MICH− to LN
with respect to 800 Hz
−0.5
±0.2
+0.5
dB
∆GvT
gain variation with temperature at
Tamb = −25 °C and +75 °C
Iline = 50 mA; with respect to
800 Hz
−
±0.2
−
dB
16.8
20.7
24.6
kΩ
Dual-tone multi-frequency input DTMF (pin 15)
Zi
input impedance
Gv
voltage gain from DTMF to LN
Iline = 15 mA; R7= 68 kΩ
24.5
25.5
26.5
dB
∆Gvf
gain variation with frequency at
f = 300 Hz and 3400 Hz
with respect to 800 Hz
−0.5
±0.2
+0.5
dB
∆GvT
gain variation with temperature at
Tamb = −25 °C and +75 °C
Iline = 50 mA; with respect
to 25 °C
−
±0.2
−
dB
−8
−
+8
dB
Iline = 15 mA; THD = 2%
1.9
2.3
−
V
Iline = 15 mA; THD = 10%
−
2.6
−
V
Iline = 15 mA; R7 = 68 kΩ;
microphone inputs open;
psophometrically weighted
(P53 curve)
−
−70
−
dBmp
17
21
25
kΩ
−
4
−
Ω
single-ended; RL = 300 Ω
24
25
26
dB
differential; RL = 600 Ω
Gain adjustment connections GAS1 and GAS2 (pins 2 and 3)
∆Gv
gain variation with R7, transmitting
amplifier
Transmitting amplifier output LN (pin 1)
VLN(rms)
Vno(rms)
output voltage (RMS value)
noise output voltage (RMS value)
Receiving amplifier input IR (pin 13)
Zi
input impedance
Receiving amplifier outputs QR+ and QR− (pins 5 and 4)
Zo
output impedance
Gv
voltage gain from IR to QR+ or QR− Iline = 15 mA; R4 = 100 kΩ
single-ended
30
31
32
dB
∆Gvf
gain variation with frequency at
f = 300 Hz and 3400 Hz
with respect to 800 Hz
−0.5
±0.2
+0.5
dB
∆GvT
gain variation with temperature at
Tamb = −25 °C and +75 °C
Iline = 50 mA; with respect to
25 °C
−
±0.2
−
dB
1996 Apr 04
10
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
SYMBOL
Vo(rms)
Vno(rms)
PARAMETER
output voltage (RMS value)
noise output voltage (RMS value)
TEA1066T
CONDITIONS
MIN.
TYP.
MAX.
UNIT
sine-wave drive; Iline = 15 mA;
Ip = 0 mA; THD = 2%;
R4 = 100 kΩ
single-ended; RL = 150 Ω
0.30
0.38
−
V
single-ended; RL = 450 Ω
0.40
0.52
−
V
differential; CL = 47 nF;
Rseries = 100 Ω; f = 3400 Hz
0.80
1.0
−
V
single-ended; RL = 300 Ω
−
50
−
µV
differential; RL = 600 Ω
−
100
−
µV
−8
−
+8
dB
Iline = 15 mA; R4 = 100 kΩ;
pin 13 (IR) open;
psophometrically weighted
(P53 curve)
Gain adjustment GAR (pin 6)
∆Gv
gain variation with R4 connected
between pin 6 and pin 5 receiving
amplifier
MUTE input (pin 16)
VIH
HIGH level input voltage
1.50
−
VCC
V
VIL
LOW level input voltage
−
−
0.3
V
IMUTE
input current
−
5
10
µA
∆Gv
voltage gain reduction between
MICL+ (pin 9) and MICL− (pin 7) to
LN (pin 1)
MUTE = HIGH
−
70
−
dB
Gv
voltage gain from DTMF to QR+ or
QR−
MUTE = HIGH; R4 = 100 kΩ;
single-ended; RL = 300 Ω
−21
−19
−17
dB
−
VCC
V
Power-down input PD (pin 14)
VIH
HIGH level input voltage
1.5
VIL
LOW level input voltage
−
−
0.3
V
IPD
input current in power-down
condition
−
5
10
µA
1996 Apr 04
11
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
SYMBOL
PARAMETER
TEA1066T
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Automatic gain control input AGC (pin 19)
∆Gv
gain control range from IR to
QR+/QR− and from MIC+/MIC− to
LN
Iline = 70 mA; R6 = 110 kΩ
between AGC and VEE
−5.5
−5.9
−6.3
dB
Iline(H)
highest line current for maximum
gain
R6 = 110 kΩ between AGC and
VEE
−
23
−
mA
Iline(L)
lowest line current for minimum gain R6 = 110 kΩ between AGC and
VEE
−
61
−
mA
∆Gv
voltage gain variation
−1.0
−1.5
−2.0
dB
between Iline = 15 mA and
Iline = 35 mA; R6 = 110 kΩ
between AGC and VEE
Iline
Rline
handbook, full pagewidth
R1
ISLPE + 0.5 mA
1
LN
TEA1066T
Rexch
DC
ICC
17
0.5 mA
AC
Vexch
Ip
VCC
C1
REG
18
C3
STAB
SLPE
11
20
I SLPE
R5
peripheral
circuits
VEE
12
R9
MBH123
Fig.7 Supply arrangement.
1996 Apr 04
12
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
MBH124
3
handbook, halfpage
(1)
Ip
(mA)
(2)
2
(3)
1
(4)
0
0
1
2
4
3 V
CC (V)
Curves (1) and (3) are valid when the receiving amplifier is not driven or when MUTE = HIGH. Curves (2) and (4) are valid when MUTE = LOW and the
receiving amplifier is driven, Vo(rms) = 150 mV, RL = 150 Ω (asymmetrical). Iline = 15 mA; VLN = 4.45 V; R1 = 620 Ω and R9 = 20 Ω.
(1) Ip = 2.55 mA.
(2) Ip = 2.1 mA.
(3) Ip = 1.2 mA.
(4) Ip = 0.75 mA.
Fig.8 Typical current Ip available from VCC for external (peripheral) circuitry with VCC > 2.2 V and VCC > 3 V.
handbook, full pagewidth
17
VCC
9
8
MICL+
10
MICH−
MICH+
(1)
7
10
MICL−
8
MICH+
MICH−
VEE
12
a. Magnetic or dynamic
microphone.
b. Electret microphone.
MBH121
c. piezoelectric microphone.
(1) May be connected to lower the terminating impedance.
Fig.9 Alternative microphone arrangements.
1996 Apr 04
13
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
handbook, full pagewidth
QR+
QR−
VEE
5
QR+
5
QR+
5
(1)
QR+
5
(2)
4
12
QR−
4
QR−
4
QR−
4
MBH122
a. Dynamic earpiece
with less than 450 Ω
impedance.
b. Dynamic earpiece with
more than 450 Ω
impedance.
c. Magnetic earpiece
with more than 450 Ω
impedance.
d. piezoelectric
earpiece.
(1) May be connected to prevent distortion (inductive load).
(2) Required to increase the phase margin (capacitive load).
Fig.10 Alternative receiver arrangements.
handbook, full pagewidth
MBH126
R6 = ∞
0
∆Gv
(dB)
−2
−4
48.7 kΩ
78.7 kΩ
110 kΩ
140 kΩ
−6
0
20
40
60
80
100
120
140
Iline(mA)
R9 = 20 Ω.
Fig.11 Variation of gain with line current, with R6 as a parameter.
1996 Apr 04
14
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
Table 1
TEA1066T
Values of resistor R6 for optimum line loss compensation, for various usual values of exchange supply
voltage Vexch and exchange feeding bridge resistance Rexch; R9 = 20 Ω
R6 (kΩ)
Vexch (V)
Rexch = 400 Ω
Rexch = 600 Ω
Rexch = 800 Ω
Rexch = 1000 Ω
24
61.9
48.7
X
X
36
100
78.7
68
60.4
48
140
110
93.1
82
60
X
X
120
102
Iline
R1
handbook, full pagewidth
17
13
9, 10
Vi
100 µF
7, 8
15
620 Ω
1
LN
VCC
IR
MICL+/MICH+
QR−
QR+
GAR
TEA1066T
DTMF
10 µF
Vi
14
100 µF
RL
600 Ω
5
MICL−/MICH−
6
R4
100 kΩ
Vo
C4
100 pF
C7 1 nF
C1
16
4
GAS1
MUTE
PD
GAS2
VEE
12
C3
4.7
µF
REG AGC STAB SLPE
18
19
11
20
R6
R5
3.6
kΩ
2
10 to 140 mA
3
R7
68 kΩ
C6
100 pF
R9
20 Ω
MBH127
Voltage gain is defined as: Gv = 20 log Vo/Vi. For measuring the gain from MICL+, MICL− or MICH+ and MICH−, the MUTE input should be LOW or
open; for measuring the DTMF input, MUTE should be HIGH. Inputs not under test should be open.
Fig.12 Test circuit for defining voltage gain of MICL+, MICL−, MICH+ and MICH− DTMF inputs.
1996 Apr 04
15
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
I line
R1
handbook, full pagewidth
17
13
9, 10
Vi
10 µF
7, 8
15
620 Ω
IR
100 µF
1
LN
VCC
QR−
16
14
600 Ω
ZL
MICL+/MICH+
QR+
TEA1066T
DTMF
GAR
GAS1
MUTE
Vo
5
MICL−/MICH−
C1
100 µF
4
6
R4
100
kΩ
C4
100 pF
C7 1 nF
2
10 to 140 mA
R7
PD
GAS2
VEE
12
C3
4.7
µF
3
C6
100 pF
REG AGC STAB SLPE
18
19
11
20
R6
R5
3.6
kΩ
R9
20 Ω
MBH128
Voltage gain is defined as: Gv = 20 log Vo/Vi.
Fig.13 Test circuit for defining voltage gain of the receiving amplifier.
1996 Apr 04
16
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
APPLICATION INFORMATION
R1
handbook, full pagewidth
620 Ω
R10
13 Ω
R2
130 kΩ
BAS11
(2x)
C5
13
100 nF
4
17
VCC
IR
QR−
R11
5
telephone
BZW14
line
(2x)
1
LN
C1
100 µF
C4
R4 100 pF
R3
6
3.92
1 nF
kΩ
C7
9, 10
7, 8
DTMF
QR+
TEA1066T
GAR
PD
16
14
from dial
and
control
circuits
MICL+/MICH+
MICL−/MICH−
SLPE
GAS1 GAS2
20
2
R8
3
REG
AGC
18
STAB
VEE
19
11
R6
R5
3.6 kΩ
12
R7
390 Ω
Zbal
MUTE
15
C3
4.7 µF
C6
R9
20 Ω
100 pF
MBH129
Typical application of the TEA1066, shown with a piezoelectric earpiece and DTMF dialling. The bridge to the left and R10 limit the current into the
circuit and the voltage across the circuit during line transients. Pulse dialling or register recall require a different protection arrangement.
Fig.14 Application diagram.
1996 Apr 04
17
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
handbook, full pagewidth
LN
VCC
DTMF
cradle
contact
TEA1066T MUTE
PD
VEE
VDD
TONE
M1
PCD3310
DP/FLO
VSS
telephone
line
BSN254A
MEA008 - 1
The dashed lines show an optional flash (register recall by timed loop break).
Fig.15 DTMF pulse set with CMOS PCD3310 dialling circuit.
1996 Apr 04
18
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
PACKAGE OUTLINE
SO20: plastic small outline package; 20 leads; body width 7.5 mm
SOT163-1
D
E
A
X
c
HE
y
v M A
Z
11
20
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
1
10
e
bp
detail X
w M
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
mm
2.65
0.30
0.10
2.45
2.25
0.25
0.49
0.36
0.32
0.23
13.0
12.6
7.6
7.4
1.27
10.65
10.00
1.4
1.1
0.4
1.1
1.0
0.25
0.25
0.1
0.9
0.4
inches
0.10
0.012 0.096
0.004 0.089
0.01
0.019 0.013
0.014 0.009
0.51
0.49
0.30
0.29
0.050
0.42
0.39
0.055
0.043
0.016
0.043
0.039
0.01
0.01
0.004
0.035
0.016
Z
(1)
θ
8o
0o
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT163-1
075E04
MS-013AC
1996 Apr 04
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
92-11-17
95-01-24
19
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
SOLDERING
Wave soldering
Introduction
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
• The package footprint must incorporate solder thieves at
the downstream end.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Reflow soldering
Reflow soldering techniques are suitable for all SO
packages.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
Repairing soldered joints
Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
1996 Apr 04
20
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
TEA1066T
DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1996 Apr 04
21
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
NOTES
1996 Apr 04
22
TEA1066T
Philips Semiconductors
Product specification
Versatile telephone transmission circuit
with dialler interface
NOTES
1996 Apr 04
23
TEA1066T
Philips Semiconductors – a worldwide company
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. (02) 805 4455, Fax. (02) 805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. (01) 60 101-1256, Fax. (01) 60 101-1250
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211,
Volodarski Str. 6, 220050 MINSK,
Tel. (172) 200 733, Fax. (172) 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. (359) 2 689 211, Fax. (359) 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS:
Tel. (800) 234-7381, Fax. (708) 296-8556
Chile: see South America
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. (852) 2319 7888, Fax. (852) 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300
COPENHAGEN S, Tel. (032) 88 2636, Fax. (031) 57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. (358) 0-615 800, Fax. (358) 0-61580 920
France: 4 Rue du Port-aux-Vins, BP317,
92156 SURESNES Cedex,
Tel. (01) 4099 6161, Fax. (01) 4099 6427
Germany: P.O. Box 10 51 40, 20035 HAMBURG,
Tel. (040) 23 53 60, Fax. (040) 23 53 63 00
Greece: No. 15, 25th March Street, GR 17778 TAVROS,
Tel. (01) 4894 339/4894 911, Fax. (01) 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block,
Dr. Annie Besant Rd. Worli, BOMBAY 400 018
Tel. (022) 4938 541, Fax. (022) 4938 722
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. (01) 7640 000, Fax. (01) 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, TEL AVIV 61180,
Tel. (03) 645 04 44, Fax. (03) 648 10 07
Italy: PHILIPS SEMICONDUCTORS,
Piazza IV Novembre 3, 20124 MILANO,
Tel. (0039) 2 6752 2531, Fax. (0039) 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku,
TOKYO 108, Tel. (03) 3740 5130, Fax. (03) 3740 5077
Korea: Philips House, 260-199 Itaewon-dong,
Yongsan-ku, SEOUL, Tel. (02) 709-1412, Fax. (02) 709-1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA,
SELANGOR, Tel. (03) 750 5214, Fax. (03) 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO,
TEXAS 79905, Tel. 9-5(800) 234-7831, Fax. (708) 296-8556
Middle East: see Italy
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. (040) 2783749, Fax. (040) 2788399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. (09) 849-4160, Fax. (09) 849-7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. (022) 74 8000, Fax. (022) 74 8341
Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC,
MAKATI, Metro MANILA,
Tel. (63) 2 816 6380, Fax. (63) 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. (022) 612 2831, Fax. (022) 612 2327
Portugal: see Spain
Romania: see Italy
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. (65) 350 2000, Fax. (65) 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd.,
195-215 Main Road Martindale, 2092 JOHANNESBURG,
P.O. Box 7430 Johannesburg 2000,
Tel. (011) 470-5911, Fax. (011) 470-5494
South America: Rua do Rocio 220 - 5th floor, Suite 51,
CEP: 04552-903-SÃO PAULO-SP, Brazil,
P.O. Box 7383 (01064-970),
Tel. (011) 821-2333, Fax. (011) 829-1849
Spain: Balmes 22, 08007 BARCELONA,
Tel. (03) 301 6312, Fax. (03) 301 4107
Sweden: Kottbygatan 7, Akalla. S-16485 STOCKHOLM,
Tel. (0) 8-632 2000, Fax. (0) 8-632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. (01) 488 2211, Fax. (01) 481 77 30
Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66,
Chung Hsiao West Road, Sec. 1, P.O. Box 22978,
TAIPEI 100, Tel. (886) 2 382 4443, Fax. (886) 2 382 4444
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. (66) 2 745-4090, Fax. (66) 2 398-0793
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. (0212) 279 2770, Fax. (0212) 282 6707
Ukraine: PHILIPS UKRAINE,
2A Akademika Koroleva str., Office 165, 252148 KIEV,
Tel. 380-44-4760297, Fax. 380-44-4766991
United Kingdom: Philips Semiconductors LTD.,
276 Bath Road, Hayes, MIDDLESEX UB3 5BX,
Tel. (0181) 730-5000, Fax. (0181) 754-8421
United States: 811 East Arques Avenue, SUNNYVALE,
CA 94088-3409, Tel. (800) 234-7381, Fax. (708) 296-8556
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. (381) 11 825 344, Fax. (359) 211 635 777
Internet: http://www.semiconductors.philips.com/ps/
For all other countries apply to: Philips Semiconductors,
Marketing & Sales Communications, Building BE-p,
P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands,
Fax. +31-40-2724825
SCDS48
© Philips Electronics N.V. 1996
All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation
or contract, is believed to be accurate and reliable and may be changed without
notice. No liability will be accepted by the publisher for any consequence of its
use. Publication thereof does not convey nor imply any license under patent- or
other industrial or intellectual property rights.
Printed in The Netherlands
417021/10/02/pp24
Document order number:
Date of release: 1996 Apr 04
9397 750 00783