PHILIPS TEA1113T

INTEGRATED CIRCUITS
DATA SHEET
TEA1113
Low voltage versatile telephone
transmission circuit with dialler
interface
Product specification
Supersedes data of 1996 Feb 08
File under Integrated Circuits, IC03
1997 Mar 27
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
FEATURES
APPLICATION
• Low DC line voltage; operates down to 1.6 V (excluding
polarity guard)
• Line powered telephone sets, cordless telephones, fax
machines and answering machines.
• Voltage regulator with adjustable DC voltage
• Provides a supply for external circuits
GENERAL DESCRIPTION
• Symmetrical high impedance inputs (64 kΩ) for
dynamic, magnetic or piezo-electric microphones
The TEA1113 is a bipolar integrated circuit that performs
all speech and line interface functions required in fully
electronic telephone sets. It performs electronic switching
between speech and dialling. The IC operates at a line
voltage down to 1.6 V DC (with reduced performance) to
facilitate the use of telephone sets connected in parallel.
• Asymmetrical high impedance input (32 kΩ) for electret
microphones
• DTMF input with confidence tone
• MUTE input for pulse or DTMF dialling
A current (proportional to the line current and internally
limited to 19.5 mA) is available to drive an LED which
indicates the on-hook/off-hook status.
• Receiving amplifier for dynamic, magnetic or
piezo-electric earpieces
• Dynamic limitation in the transmit direction to prevent
distortion of the transmit line and sidetone signals
The transmit signal on the line is dynamically limited to
prevent distortion at high transmit levels for both the
sending line and sidetone signals. The microphone
amplifier can be disabled during speech condition by
means of a microphone mute function.
• AGC line loss compensation for microphone and
earpiece amplifiers
• LED on-hook/off-hook status indication
• Microphone mute function available with switch.
All statements and values refer to all versions unless
otherwise specified.
QUICK REFERENCE DATA
Iline = 15 mA; VEE = 0 V; RSLPE = 20 Ω; CDLS = 470 nF; AGC pin connected to VEE; Zline = 600 Ω; f = 1 kHz;
Tamb = 25 °C; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
11
TYP.
−
MAX.
UNIT
140
mA
Iline
line current operating range
normal operation
with reduced performance
1
−
11
mA
ILED(max)
maximum supply current available
Iline = 18 mA
−
0.6
−
mA
Iline > 76 mA
−
19.5
−
mA
VLN
DC line voltage
3.7
4.0
4.3
V
VLN(max)(p-p)
maximum output voltage swing
(peak-to-peak value)
3.8
4.65
−
V
ICC
internal current consumption
VCC = 3.2 V
−
1.3
1.6
mA
VCC
supply voltage for peripherals
Ip = 0 mA
2.8
3.2
−
V
Gvtrx
typical voltage gain range
VMIC = 2 mV (RMS)
38.8
−
51.8
dB
microphone amplifier
receiving amplifier
∆Gvtrx
gain control range for microphone and
receiving amplifiers with respect to
Iline = 15 mA
∆Gvtxm
microphone amplifier gain reduction
1997 Mar 27
VIR = 4 mV (RMS)
19.3
−
31.3
dB
Iline = 85 mA
−
5.8
−
dB
−
80
−
dB
2
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
ORDERING INFORMATION
PACKAGE
TYPE
NUMBER
NAME
DESCRIPTION
VERSION
TEA1113
DIP16
plastic dual in-line package; 16 leads (300 mil)
SOT38-4
TEA1113T
SO16
plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1
BLOCK DIAGRAM
GAR
QR
MUTE
handbook, full pagewidth
15
IR
9
14
8
V− I
16 VCC
1
V− I
LN
DTMF
7
ATT.
CURRENT
REFERENCE
V− I
5
MIC+
GAS
12
4 REG
V− I
MIC−
11
DLS/MMUTE 6
DYNAMIC
LIMITER
AGC
CIRCUIT
LOW VOLTAGE
CIRCUIT
TEA1113
LED
DRIVER
13
10
3
2
SLPE
VEE
AGC
ILED
Fig.1 Block diagram.
1997 Mar 27
3
MBG018
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
PINNING
SYMBOL
PIN
DESCRIPTION
LN
1
positive line terminal
SLPE
2
slope (DC resistance) adjustment
ILED
3
available output current to drive an
LED
REG
4
line voltage regulator decoupling
GAS
5
sending gain adjustment
DLS/
MMUTE
6
dynamic limiter timing adjustment
and microphone mute input
DTMF
7
dual-tone multi-frequency input
MUTE
8
mute input to select speech or
dialling mode (active LOW)
IR
9
receiving amplifier input
AGC
10
automatic gain control - line loss
compensation
MIC−
11
inverting microphone amplifier
input
MIC+
12
non-inverting microphone amplifier
input
VEE
13
negative line terminal
QR
14
receiving amplifier output
GAR
15
receive gain adjustment
VCC
16
supply voltage for speech circuit
and peripherals
handbook, halfpage
16 VCC
SLPE 2
15 GAR
ILED 3
14 QR
REG 4
TEA1113
13 VEE
GAS 5
12 MIC+
DLS/MMUTE 6
11 MIC−
DTMF 7
10 AGC
MUTE 8
9 IR
MBG015
Fig.2 Pin configuration.
(RCC in the audio-frequency range). The voltage at pin
SLPE is proportional to the line current. Figure 3 illustrates
the supply configuration.
FUNCTIONAL DESCRIPTION
All data given in this chapter are typical values, except
when otherwise specified.
The IC regulates the line voltage at the pin LN, and it can
be calculated as follows:
Supply (pins LN, SLPE, VCC and REG)
V LN = V ref + R SLPE × I SLPE
The supply for the TEA1113 and its peripherals is obtained
from the telephone line.
I SLPE = I line – I CC – I p – I∗ = I LED + I sh
The ICs generate a stabilized reference voltage (Vref)
between pins LN and SLPE. This reference voltage is
equal to 3.7 V, is temperature compensated and can be
adjusted by means of an external resistor (RVA). It can be
increased by connecting the RVA resistor between
pins REG and SLPE, or decreased by connecting the RVA
resistor between pins REG and LN. The voltage at
pin REG is used by the internal regulator to generate the
stabilized reference voltage and is decoupled by a
capacitor (CREG) which is connected to VEE. This
capacitor, converted into an equivalent inductance (see
Section “Set impedance”), realizes the set impedance
conversion from its DC value (RSLPE) to its AC value
1997 Mar 27
LN 1
Iline: line current
ICC: current consumption of the IC
Ip: supply current for peripheral circuits
I*: current consumed between LN and VEE
ILED: supply current for the LED component
Ish: the excess line current shunted to SLPE (and VEE)
via LN.
4
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
The preferred value for RSLPE is 20 Ω. Changing RSLPE will affect more than the DC characteristics; it also influences the
microphone and DTMF gains, the LED supply current characteristic, the gain control characteristics, the sidetone level
and the maximum output swing on the line.
handbook, full pagewidthRline
Iline
RCC
619 Ω
ILED
LN
VCC
Ip
from preamp
Rexch
TEA1113
ICC
I*
Ish
ILED
CVCC
100 µF
peripheral
circuits
LED
DRIVER
Vexch
ISLPE
SLPE
REG
RSLPE
CREG
4.7 µF
20 Ω
VEE
MBG019
Fig.3 Supply configuration.
MGD188
5.5
handbook, halfpage
Vref
(V)
4.5
(1)
(2)
3.5
(3)
2.5
104
105
106
RVA (Ω)
107
(1) RVA between REG and SLPE.
(2) No RVA.
(3) RVA between REG and LN.
Fig.4 Reference voltage adjustment by a RVA resistor.
1997 Mar 27
5
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
The internal circuitry of the TEA1113 is supplied from
pin VCC. This voltage supply is derived from the line
voltage by means of a resistor (RCC) and must be
decoupled by a capacitor CVCC. It may also be used to
supply peripheral circuits such as dialling or control
circuits. The VCC voltage depends on the current
consumed by the IC and the peripheral circuits as shown
by the formula (see also Figs 5 and 6). RCCint is the internal
impedance of the voltage supply point, and Irec is the
current consumed by the output stage of the earpiece
amplifier.
Set impedance
In the audio frequency range, the dynamic impedance is
mainly determined by the RCC resistor. The equivalent
impedance of the circuits is illustrated in Fig.7.
LED supply (pin ILED)
The TEA1113 gives an on-hook/off-hook status indication.
This is achieved by a current made available to drive an
LED connected between pins ILED and LN. In the low
voltage area, which corresponds to low line current
conditions, no current is available for this LED. For line
currents higher than a threshold current, the ILED current
increases proportionally to the line current (with a ratio of
one third).The ILED current is internally limited to 19.5 mA
(see Fig.8).
V CC = V CCO – R CCint × ( I p – I rec )
V CCO = V LN – R CC × I CC
The DC line current flowing into the set is determined by
the exchange supply voltage (Vexch), the feeding bridge
resistance (Rexch), the DC resistance of the telephone line
(Rline) and the reference voltage (Vref). With line currents
below 8 mA, the internal reference voltage (generating
Vref) is automatically adjusted to a lower value. This means
that more sets can operate in parallel with DC line voltages
(excluding the polarity guard) down to an absolute
minimum voltage of 1.6 V. At currents below 8 mA, the
circuit has limited sending and receiving levels. This is
called the low voltage area.
handbook, halfpage
RCCint
VCCO
For 17 mA < Iline < 77 mA:
I line – 17
I LED = --------------------3
This LED driver is referenced to SLPE. Consequently, all
the ILED supply current will flow through the RSLPE resistor.
The AGC characteristics are not disturbed (see Fig.3 for
the supply configuration).
Microphone amplifier (pins MIC+, MIC− and GAS)
The TEA1113 has symmetrical microphone inputs.
The input impedance between pins MIC+ and MIC− is
64 kΩ (2 × 32 kΩ). The voltage gain from pins MIC+/MIC−
to pin LN is set to 51.8 dB (typ). The gain can be
decreased by connecting an external resistor RGAS
between pins GAS and REG. The adjustment range is
13 dB. A capacitor CGAS connected between pins GAS
and REG can be used to provide a first-order low-pass
filter. The cut-off frequency corresponds to the time
constant CGAS × (RGASint // RGAS). RGASint is the internal
resistor which sets the gain with a typical value of 69 kΩ.
VCC
Irec
TEA1113
PERIPHERAL
CIRCUIT
IP
Automatic gain control is provided on this amplifier for line
loss compensation.
MBE792
Dynamic limiter and microphone mute
(pin DLS/MMUTE)
VEE
The dynamic limiter only acts on the microphone channel,
this is to prevent clipping of the line signal. To prevent
distortion, the microphone gain is rapidly reduced when
peaks on the line signal exceed an internally determined
threshold level or when the current in the transmit output
stage is insufficient. The time in which the gain reduction
is realized is very short (attack time). The microphone
channel stays in the reduced gain condition until the peaks
Fig.5 VCC voltage supply for peripherals.
1997 Mar 27
6
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
on the line signal remain below the threshold level.
The microphone gain then returns to its nominal value after
a time determined by the capacitor CDLS (release time).
The IC can be used with different configurations of feeding
bridge (supply voltage and bridge resistance) by
connecting an external resistor RAGC between pins AGC
and VEE. This resistor enables the Istart and Istop line
currents to be increased (the ratio between Istart and Istop is
not affected by the resistor). The AGC function is disabled
when pin AGC is left open-circuit.
The maximum output swing on the line depends on the DC
voltage setting (Vref). The internal threshold level is
automatically adapted.
A LOW level on pin DLS/MMUTE inhibits the microphone
inputs MIC+ and MIC− without affecting the DTMF and
receiving inputs. Removing the LOW level from pin
DLS/MMUTE provides the normal function of the
microphone amplifier after a short time which is
determined by capacitor CDLS. With the value of the
capacitor at 470 nF, the release time is in the order of a
few tenths of a millisecond. The microphone mute function
can be realized by a simple switch as illustrated in Fig.9.
Mute function (pin MUTE)
The mute function performs the switching between the
speech mode and the dialling mode. When MUTE is LOW
or open-circuit, the DTMF input is enabled and the
microphone and receiving amplifiers inputs are disabled.
When MUTE is HIGH, the microphone and receiving
amplifiers inputs are enabled while the DTMF input is
disabled.
Receiving amplifier (pins IR, GAR and QR)
DTMF amplifier (pin DTMF)
The receiving amplifier has one input (IR) and one output
(QR). The input impedance between pin IR and pin VEE is
20 kΩ. The voltage gain from pin IR to pin QR is fixed to
31.3 dB (typ). The gain can be decreased by connecting
an external resistor RGAR between pins GAR and QR; the
adjustment range is 12 dB. Two external capacitors CGAR
(connected between GAR and QR) and CGARS (connected
between GAR and VEE) ensure stability. The CGAR
capacitor provides a first-order low-pass filter. The cut-off
frequency corresponds to the time constant
CGAR × (RGARint // RGAR). RGARint is the internal resistor
which sets the gain with a typical value of 100 kΩ.
The relationship CGARS = 10 × CGAR must be fulfilled to
ensure stability.
When the DTMF amplifier is enabled, dialling tones may
be sent on line. These tones can be heard in the earpiece
at a low level (confidence tone).
The TEA1113 has an asymmetrical DTMF input. The input
impedance between DTMF and VEE is 20 kΩ. The voltage
gain from pin DTMF to pin LN is 25.4 dB. When the
resistor RGAS is connected, to decrease the microphone
gain, the DTMF gain varies in the same way (the DTMF
gain is 26.4 dB lower than the microphone gain with no
AGC control).
The automatic gain control has no effect on the DTMF
amplifier.
The output voltage of the receiving amplifier is specified for
continuous wave drive. The maximum output swing
depends on the DC line voltage, the RCC resistor, the ICC
current consumption of the circuit, the Ip current
consumption of the peripheral circuits and the load
impedance.
Sidetone suppression
The TEA1113 anti-sidetone network comprising
RCC // Zline, Rast1, Rast2, Rast3, RSLPE and Zbal (see Fig.10)
suppresses the transmitted signal in the earpiece.
Maximum compensation is obtained when the following
conditions are fulfilled:
Automatic gain control is provided on this amplifier for line
loss compensation.
R SLPE × R ast1 = R CC × ( R ast2 + R ast3 )
Automatic gain control (pin AGC)
( R ast2 × ( R ast3 + R SLPE ) )
k = ---------------------------------------------------------------------( R ast1 × R SLPE )
The TEA1113 performs automatic line loss compensation.
The automatic gain control varies the gain of the
microphone amplifier and the gain of the receiving
amplifier in accordance with the DC line current.
The control range is 5.8 dB (which corresponds
approximately to a line length of 5 km for a 0.5 mm
diameter twisted-pair copper cable with a DC resistance of
176 Ω/km and an average attenuation of 1.2 dB/km).
1997 Mar 27
TEA1113
Z bal = k × Z line
The scale factor k is chosen to meet the compatibility with
a standard capacitor from the E6 or E12 range for Zbal.
7
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
In practice, Zline varies considerably with the line type and
the line length. Therefore, the value chosen for Zbal should
be for an average line length which gives satisfactory
sidetone suppression with short and long lines.
The suppression also depends on the accuracy of the
match between Zbal and the impedance of the average
line.
handbook, halfpage
Vref
RSLPE
20 Ω
VEE
MBG016
Ip
(mA)
3
2
(1)
1
0
2
3
VCC (V)
4
(1) With RVA resistor.
(2) Without RVA resistor.
Fig.6
Typical current IP available from VCC for
peripheral circuits at Iline = 15 mA.
1997 Mar 27
REG
VCC
CREG
4.7 µF
CVCC
100 µF
MBE788
Fig.7 Equivalent impedance between LN and VEE.
handbook, halfpage
1
RCC
619 Ω
Leq = CREG × RSLPE × RP; RP = internal resistance; RP = 15.5 kΩ.
More information on the balancing of an anti-sidetone
bridge can be obtained in our publication “Applications
Handbook for Wired Telecom Systems, IC03b”, order
number 9397 750 00811.
0
RP
SLPE
A Wheatstone bridge configuration (see Fig.11) may also
be used.
(2)
LN
LEQ
The anti-sidetone network for the TEA1113 (as shown in
Fig.14) attenuates the receiving signal from the line by
32 dB before it enters the receiving amplifier.
The attenuation is almost constant over the whole audio
frequency range.
4
TEA1113
8
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
MBE784
100
handbook, halfpage
I
(mA)
ISLPE
80
handbook, halfpage
DLS/MMUTE
RDLS
60
3.3 kΩ
CDLS
Ish
40
470 nF
ILED
20
VEE
MBG017
0
0
20
40
60
80
100
Iline (mA)
Fig.8 Available current to drive an LED.
Fig.9 Microphone mute function.
LN
handbook, full pagewidth
Zline
RCC
Rast1
Im
VEE
IR
Zir
Rast2
RSLPE
Rast3
SLPE
Zbal
MBE787
Fig.10 Equivalent circuit of TEA1113 anti-sidetone bridge.
1997 Mar 27
9
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
handbook, full pagewidth
TEA1113
LN
Zline
RCC
Zbal
IR
Im
VEE
RSLPE
Zir
Rast1 RA
SLPE
MBE786
Fig.11 Equivalent circuit of an anti-sidetone network in a Wheatstone bridge configuration.
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
VLN
Vn(max)
PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
positive continuous line voltage
VEE − 0.4
12.0
V
repetitive line voltage during switch-on or
line interruption
VEE − 0.4
13.2
V
maximum voltage on pins ILED, SLPE
VEE − 0.4
VLN + 0.4
V
maximum voltage on all other pins
Iline
line current
RSLPE = 20 Ω;
see Figs 12 and 13
Ptot
total power dissipation
Tamb = 75 °C;
see Figs 12 and 13
VEE − 0.4
VCC + 0.4
V
−
140
mA
TEA1113
−
625
mW
TEA1113T
−
416
mW
Tstg
IC storage temperature
−40
+125
°C
Tamb
operating ambient temperature
−25
+75
°C
THERMAL CHARACTERISTICS
SYMBOL
Rth j-a
1997 Mar 27
PARAMETER
VALUE
UNIT
thermal resistance from junction to ambient in free air (TEA1113)
80
K/W
thermal resistance from junction to ambient in free air mounted on epoxy
board 40.1 × 19.1 × 1.5 mm (TEA1113T)
130
K/W
10
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
MBE782
150
handbook, halfpage
Iline
(mA)
(4)
(3)
(2)
(1)
110
70
LINE
Tamb (°C)
Ptot (mW)
(1)
45
1000
(2)
55
875
(3)
65
750
(4)
75
625
30
2
4
6
8
10
12
VLN − VSLPE (V)
Fig.12 Safe operating area (TEA1113).
MLC202
150
handbook, halfpage
I LN
(mA)
130
110
(1)
LINE
Tamb (°C)
Ptot (mW)
(2)
(1)
45
666
(2)
55
583
(3)
65
500
(4)
75
416
90
(3)
70
(4)
50
30
2
4
6
8
10
12
V LN V SLPE (V)
Fig.13 Safe operating area (TEA1113T).
1997 Mar 27
11
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
CHARACTERISTICS
Iline = 15 mA; VEE = 0 V; RSLPE = 20 Ω; CDLS = 470 nF; AGC pin connected to VEE; Zline = 600 Ω; f = 1 kHz;
Tamb = 25 °C; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supply (pins VLN, VCC, SLPE and REG)
Vref
stabilized voltage between LN
and SLPE
VLN
DC line voltage
3.45
3.7
3.95
V
Iline = 1 mA
−
1.6
−
V
Iline = 4 mA
−
2.5
−
V
Iline = 15 mA
3.7
4
4.3
V
Iline = 140 mA
−
−
7.0
V
DC line voltage with an external
resistor RVA
RVA(LN−REG) = 82 kΩ
−
3.6
−
V
RVA(SLPE−REG) = 27 kΩ
−
4.75
−
V
∆VLN(T)
DC line voltage variation with
temperature referred to 25 °C
Tamb = −25 to +75 °C
−
±30
−
mV
ICC
internal current consumption
VCC = 3.2 V
−
1.3
1.6
mA
VCC
supply voltage for peripherals
Ip = 0 mA
2.8
3.2
−
V
RCCint
equivalent supply voltage
impedance
Ip = 0.5 mA
−
550
620
Ω
VLN(exR)
LED supply (pin ILED)
Iline(h)
highest line current for
ILED < 0.6 mA
−
18
−
mA
Iline(l)
lowest line current for maximum
ILED
−
76
−
mA
ILED(max)
maximum supply current
available
−
19.5
−
mA
differential between pins
MIC+ and MIC−
−
64
−
kΩ
single-ended between pins
MIC+/MIC− and VEE
−
32
−
kΩ
Microphone amplifier (pins MIC+, MIC− and GAS)
Zi
input impedance
Gvtx
voltage gain from MIC+/MIC− to
LN
VMIC = 2 mV (RMS)
50.6
51.8
53
dB
∆Gvtx(f)
gain variation with frequency
referred to 1 kHz
f = 300 to 3400 Hz
−
±0.2
−
dB
∆Gvtx(T)
gain variation with temperature
referred to 25 °C
Tamb = −25 to +75 °C
−
±0.3
−
dB
CMRR
common mode rejection ratio
−
80
−
dB
∆Gvtxr
gain voltage reduction range
external resistor connected
between GAS and REG
−
−
13
dB
Vnotx
noise output voltage at pin LN;
pins MIC+ / MIC− shorted
through 200 Ω
psophometrically weighted
(P53 curve)
−
−70.5
−
dBmp
1997 Mar 27
12
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
SYMBOL
PARAMETER
TEA1113
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Dynamic limiter and microphone mute (pin DLS/MMUTE)
DYNAMIC LIMITER BEHAVIOUR
VLN(max)(p-p) maximum output voltage swing
on the line (peak-to-peak value)
Iline = 15 mA; Vref = 3.7 V
3.8
4.65
−
Iline = 4 mA
−
1.6
−
THD
VMIC = 4 mV (RMS) + 10 dB
−
−
2
%
VMIC = 4 mV (RMS) + 15 dB
−
−
10
%
total harmonic distortion
V
tatt
attack time, VMIC jumps from
2 mV up to 20 mV
CDLS = 470 nF
−
1.5
5
ms
trel
release time, VMIC jumps from
20 mV down to 2 mV
CDLS = 470 nF
50
150
−
ms
DLS/MMUTE = LOW
MICROPHONE MUTE INPUT
∆Gvtxm
gain reduction
−
80
−
dB
VIL
LOW level input voltage
VEE − 0.4
−
VEE + 0.3
V
IIL
LOW level input current
40
60
−
µA
trel
release time after a LOW level
on pin DLS/MMUTE
−
30
−
ms
−
20
−
kΩ
CDLS = 470 nF
Receiving amplifier (pins IR, QR and GAR)
Zi
input impedance
Gvrx
voltage gain from IR to QR
VIR = 4 mV (RMS)
30.3
31.3
32.3
dB
∆Gvrx(f)
gain variation with frequency
referred to 1 kHz
f = 300 to 3400 Hz
−
±0.2
−
dB
∆Gvrx(T)
gain variation with temperature
referred to 25 °C
Tamb = −25 to +75 °C
−
±0.3
−
dB
∆Gvrxr
gain voltage reduction range
external resistor connected
between GAR and QR
−
−
12
dB
Vo(rms)
maximum output voltage
(RMS value)
Ip = 0 mA sine wave drive;
RL = 150 Ω; THD = 2%
240
290
−
mV
Ip = 0 mA sine wave drive;
RL = 450 Ω; THD = 2%
350
410
−
mV
RL = 150 Ω;
IR open-circuit;
psophometrically weighted
(P53 curve)
−
−86
−
dBVp
Iline = 85 mA
−
5.8
−
dB
Vnorx(rms)
noise output voltage at pin QR
(RMS value)
Automatic gain control (pin AGC)
∆Gvtrx
gain control range for
microphone and receiving
amplifiers with respect to
Iline = 15 mA
Istart
highest line current for maximum
gain
−
25
−
mA
Istop
lowest line current for minimum
gain
−
59
−
mA
1997 Mar 27
13
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
SYMBOL
PARAMETER
TEA1113
CONDITIONS
MIN.
TYP.
MAX.
UNIT
DTMF amplifier (pin DTMF)
Zi
input impedance
−
20
−
kΩ
Gvdtmf
voltage gain from DTMF to LN
VDTMF = 25 mV (RMS);
MUTE = LOW
24.2
25.4
26.6
dB
∆Gvdtmf(f)
gain variation with frequency
referred to 1 kHz
f = 300 to 3400 Hz
−
±0.2
−
dB
∆Gvdtmf(T)
gain variation with temperature
referred to 25 °C
Tamb = −25 to +75 °C
−
±0.5
−
dB
Gvct
voltage gain from DTMF to QR
(confidence tone)
RL = 150 Ω;
VDTMF = 25 mV (RMS)
−
−18
−
dB
V
Mute function (pin MUTE)
VIL
LOW level input voltage
VEE − 0.4
−
VEE + 0.3
VIH
HIGH level input voltage
VEE + 1.5
−
VCC + 0.4 V
IMUTE
input current
MUTE = HIGH
−
1.25
3
µA
∆Gvtrxm
gain reduction for microphone
and receiving amplifiers
MUTE = LOW
−
80
−
dB
1997 Mar 27
14
1997 Mar 27
VDR
95 V
15
100 pF
CGAR
LN
BC547
BZX79C10
470 kΩ
Rpd1
100 pF
390 Ω
Zbal
MUTE
DTMF
VCC
ILED
4.7 µF
CREG
470 nF
CDLS
AGC VEE DLS/MMUTE
TEA1113
REG
CGAS
RSLPE
20 Ω
SLPE GAS
MIC−
GAR
MIC+
QR
IR
Rast3
1 nF
CGARS
Rast2
3.92 kΩ
CIR
100 µF
3.3 kΩ
RDLS
CVCC
signal
from
dial and
control
circuits
Rpd2
470 kΩ
BF473
supply for
peripheral
circuits
RCC
619 Ω
BC558
MGD020
Rpd3
1 MΩ
BC547
470 kΩ
Rpd4
68 kΩ
Rpd6
Rpd5
470 kΩ
PD
input
Low voltage versatile telephone
transmission circuit with dialler interface
Fig.14 Typical application of the TEA1113 in sets with Pulse Dialling or Flash facilities.
Rlimit
3.9 Ω
BSN254
BZV85C10
4x
BAS11
Rast1
130 kΩ
handbook, full pagewidth
b/a
Telephone
line
a/b
Rprot
10 Ω
Philips Semiconductors
Product specification
TEA1113
APPLICATION INFORMATION
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
PACKAGE OUTLINES
DIP16: plastic dual in-line package; 16 leads (300 mil)
SOT38-4
ME
seating plane
D
A2
A
A1
L
c
e
Z
w M
b1
(e 1)
b
b2
MH
9
16
pin 1 index
E
1
8
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
min.
A2
max.
b
b1
b2
c
D (1)
E (1)
e
e1
L
ME
MH
w
Z (1)
max.
mm
4.2
0.51
3.2
1.73
1.30
0.53
0.38
1.25
0.85
0.36
0.23
19.50
18.55
6.48
6.20
2.54
7.62
3.60
3.05
8.25
7.80
10.0
8.3
0.254
0.76
inches
0.17
0.020
0.13
0.068
0.051
0.021
0.015
0.049
0.033
0.014
0.009
0.77
0.73
0.26
0.24
0.10
0.30
0.14
0.12
0.32
0.31
0.39
0.33
0.01
0.030
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
92-11-17
95-01-14
SOT38-4
1997 Mar 27
EUROPEAN
PROJECTION
16
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
SO16: plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1
D
E
A
X
c
y
HE
v M A
Z
16
9
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
1
L
8
e
0
detail X
w M
bp
2.5
5 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
Z (1)
mm
1.75
0.25
0.10
1.45
1.25
0.25
0.49
0.36
0.25
0.19
10.0
9.8
4.0
3.8
1.27
6.2
5.8
1.05
1.0
0.4
0.7
0.6
0.25
0.25
0.1
0.7
0.3
0.01
0.019 0.0098 0.39
0.014 0.0075 0.38
0.16
0.15
0.050
0.24
0.23
0.041
0.039
0.016
0.028
0.020
0.01
0.01
0.004
0.028
0.012
inches
0.069
0.0098 0.057
0.0039 0.049
θ
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT109-1
076E07S
MS-012AC
1997 Mar 27
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
91-08-13
95-01-23
17
o
8
0o
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
WAVE SOLDERING
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
DIP
SOLDERING BY DIPPING OR BY WAVE
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
• The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
REPAIRING SOLDERED JOINTS
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
SO
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
1997 Mar 27
TEA1113
18
Philips Semiconductors
Product specification
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1113
DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1997 Mar 27
19
Philips Semiconductors – a worldwide company
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101, Fax. +43 1 60 101 1210
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580/xxx
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, TEL AVIV 61180,
Tel. +972 3 645 0444, Fax. +972 3 649 1007
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Middle East: see Italy
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2870, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Internet: http://www.semiconductors.philips.com
© Philips Electronics N.V. 1997
SCA53
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
417027/1200/02/pp20
Date of release: 1997 Mar 27
Document order number:
9397 750 00632