Data Sheet No.PD94253 IRU3048 DUAL SYNCHRONOUS PWM CONTROLLER CIRCUITRY AND LDO CONTROLLER PRELIMINARY DATA SHEET FEATURES DESCRIPTION Dual Synchronous Controller in 16-Pin Package with 1808 out-of-phase operation LDO Controller with 40mA drive Configured as 2-Independent PWM Controller Flexible, Same or Separate Supply Operation Operation from 4V to 25V Input Internal 200KHz Oscillator Soft-Start controls all outputs Fixed Frequency Voltage Mode 500mA Peak Output Drive Capability Programmable Outputs The IRU3048 IC combines a Dual synchronous Buck controller and a linear regulator controller, providing a cost-effective, high performance and flexible solution for multi-output applications. The Dual synchronous controller is configured as 2-independent PWM controller. IRU3048 provides a separate adjustable output by driving a switch as a linear regulator. This device features an internal 200KHz oscillator, under-voltage lockout for all input supplies, an external programmable soft start function as well as output under-voltage detection that latches off the device when an output short is detected. APPLICATIONS DDR Memory Source Sink Vtt Application Graphic Card Hard Disk Drive Power supplies requiring multiple outputs TYPICAL APPLICATION 12V 5V VcH1 VcH2 Vcc HDrv1 Q2 LDrv1 Q3 L1 VOUT1 3.3V Q1 C6 VOUT3 C1 R1 V OUT3 Fb3 C2 R2 C3 R3 C4 R4 U1 IRU3048 PGnd R5 Fb1 Fb2 Comp1 R6 HDrv2 Q4 LDrv2 Q5 Comp2 L2 VOUT2 SS Gnd C5 R7 C7 R8 Figure 1 - Typical application of IRU3048 configured as 2-independent converter. PACKAGE ORDER INFORMATION TA (°C) 0 To 70 0 To 70 Rev. 1.7 09/12/02 DEVICE IRU3048CF IRU3048CS www.irf.com PACKAGE 16-Pin TSSOP (F) 16-Pin SOIC NB (S) 1 IRU3048 ABSOLUTE MAXIMUM RATINGS Vcc Supply Voltage .................................................. VcH1=VcH2 Supply Voltage ...................................... Storage Temperature Range ...................................... Operating Junction Temperature Range ..................... 25V 30V (not rated for inductive load) -65°C To 150°C 0°C To 125°C PACKAGE INFORMATION 16-PIN PLASTIC TSSOP (F) 16-PIN PLASTIC SOIC NB (S) TOP VIEW TOP VIEW Gnd 1 16 Fb1 Gnd 1 16 Fb1 Fb2 2 15 SS Fb2 2 15 SS Comp1 3 14 Fb3 Comp1 3 14 Fb3 Comp2 4 13 VOUT3 Comp2 4 13 VOUT3 VcH2 5 12 VcH1 VcH2 5 12 VcH1 HDrv2 6 11 HDrv1 HDrv2 6 11 HDrv1 LDrv2 7 10 LDrv1 LDrv2 7 10 LDrv1 PGnd 8 9 Vcc PGnd 8 9 Vcc uJA=908C/W uJA=858C/W ELECTRICAL SPECIFICATIONS Unless otherwise specified, these specifications apply over Vcc=5V, VcH1=VcH2=12V, TA=0 to 70°C. Typical values refer to TA=25°C. Low duty cycle pulse testing is used which keeps junction and case temperatures equal to the ambient temperature. PARAMETER Reference Voltage Fb Voltage Fb Voltage Line Regulation UVLO UVLO Threshold - Vcc UVLO Hysteresis - Vcc UVLO Threshold - VcH1 UVLO Hysteresis - VcH1 UVLO Threshold - VcH2 UVLO Hysteresis - VcH2 UVLO Threshold - Fb UVLO Hysteresis - Fb Supply Current Vcc Dynamic Supply Current VcH1 Dynamic Supply Current VcH2 Dynamic Supply Current Vcc Static Supply Current VcH1 Static Supply Current VcH2 Static Supply Current Soft-Start Section Charge Current 2 SYM VFB LREG TEST CONDITION MIN TYP MAX UNITS 1.225 1.250 0.2 1.275 V % 5<Vcc<12 UVLOV CC Supply Ramping Up UVLOV CH1 Supply Ramping Up UVLOV CH2 Supply Ramping Up UVLOFB Fb Ramping Down Dyn ICC Dyn ICH1 Dyn ICH2 ICCQ ICH1Q ICH2Q Freq=200KHz, CL=1500pF Freq=200KHz, CL=1500pF Freq=200KHz, CL=1500pF SS=0V SS=0V SS=0V SSIB SS=0V www.irf.com 15 4.2 0.25 3.5 0.2 3.5 0.2 0.6 0.1 V V V V V V V V 5 7 7 3.5 2 2 mA mA mA mA mA mA 25 30 mA Rev. 1.7 09/12/02 IRU3048 PARAMETER SYM Error Amp Fb Voltage Input Bias Current Fb Voltage Input Bias Current Transconductance 1 Transconductance 2 Oscillator Frequency Ramp Amplitude Output Drivers Rise Time Fall Time Dead Band Time Max Duty Cycle Min Duty Cycle LDO Controller Drive Current Fb Voltage Input Bias Current IFB1 IFB2 gm1 gm2 TEST CONDITION SS=3V SS=0V Freq VRAMP Tr Tf TDB TON TOFF MIN CL=1500pF CL=1500pF ILDO VFBLDO ILDO(BIAS) MAX 50 85 0 30 1.225 UNITS mA mA mmho mmho -0.1 -64 400 600 180 Fb=1V, Freq=200KHz Fb=1.5V TYP 200 1.25 220 KHz VPP 35 50 150 90 0 100 100 250 ns ns ns % % 45 1.25 0.5 1.275 2 mA V mA PIN DESCRIPTIONS PIN# 1 2 16 PIN SYMBOL Gnd Fb2 Fb1 3 4 5 12 Comp1 Comp2 VcH2 VcH1 6 11 HDrv2 HDrv1 7 10 8 LDrv2 LDrv1 PGnd 9 13 14 15 Vcc VOUT3 Fb3 SS Rev. 1.7 09/12/02 PIN DESCRIPTION Ground pin. Inverting inputs to the error amplifiers. These pins work as feedback inputs for each channel, and are connected directly to the output of the switching regulator via a resistor divider to set the output voltages. Compensation pins for the error amplifiers. Supply voltage for the high side output drivers. These are connected to voltages that must be at least 4V higher than their bus voltages (assuming 5V threshold MOSFET). A minimum of 1mF high frequency capacitor must be connected from these pins to PGnd pin to provide peak drive current capability. Output driver for the high side power MOSFET. Connect a diode, such as BAT54 or 1N4148, from these pins to ground for the application when the inductor current goes negative (Source/Sink), soft-start at no load and for the fast load transient from full load to no load. Output driver for the synchronous power MOSFET. This pin serves as the separate ground for MOSFET’s driver and should be connected to the system’s ground plane. Supply voltage for the internal blocks of the IC. Driver signal for the LDO’s external transistor. LDO’s feedback pin, connected to a resistor divider to set the output voltage of LDO. Soft-Start pin. The converter can be shutdown by pulling this pin below 0.5V. www.irf.com 3 IRU3048 BLOCK DIAGRAM Vcc 9 12 V c H 1 3V Bias Generator 25uA 1.25V 11 HDrv1 64uA Max 4.2V / 4.0V POR UVLO SS 15 VcH1 VcH2 3.5V / 3.3V 3.5V / 3.3V POR PWM Comp1 10 LDrv1 Error Amp1 25K 1.25V R 25K Q Fb1 16 S Reset Dom Comp1 3 Ramp1 5 VcH2 Set1 SS > 2V Two Phase Oscillator Ramp2 6 HDrv2 Set2 S PWM Comp2 Q Error Amp2 25K 1.25V 25K Fb2 2 Comp2 4 7 LDrv2 R Reset Dom 0.5V 8 PGnd POR Vcc 25K 1.25V 2V 25K Fb3 14 SS 40mA LDO Controller Gnd 13 V OUT3 1 Figure 2 - Block diagram of the IRU3048. 4 www.irf.com Rev. 1.7 09/12/02 IRU3048 THEORY OF OPERATION Introduction The IRU3048 is designed for multi-outputs applications. It includes two synchronous buck controllers and a linear regulator controller. The two synchronous controller operates with fixed frequency voltage mode and is configured as two independent controllers. The timing of the IC is provided through an internal oscillator circuit. These are two out of phase oscillators. Soft-Start The IRU3048 has a programmable soft start to control the output voltage rise and limit the current surge at the start-up. To ensure correct start-up, the soft-start sequence initiates when the Vcc, VcH1 and VcH2 rise above their threshold and generates the Power On Reset (POR) signal. Soft-start function operates by sourcing an internal current to charge an external capacitor to about 3V. Initially, the soft-start function clamps the E/ A’s output of the PWM converter. As the charging voltage of the external capacitor ramps up, the PWM signals increase from zero to the point the feedback loop takes control. Out of Phase Operation The IRU3048 drives its two output stages 1808 out of phase. In application with single input voltage, the out of phase operation reduces the input ripple current. This results in much smaller RMS current in the input capacitor and reduction of input capacitors. Shutdown The converter can be shutdown by pulling the soft-start pin below 0.5V. This can be easily done by using an external small signal transistor. During shutdown the MOSFET drivers and the LDO controller turn off. Short-Circuit Protection The outputs are protected against the short circuit. The IRU3048 protects the circuit for shorted output by sensing the output voltages. The IRU3048 shuts down the PWM signals and LDO controller, when the output voltages drops below the set values. Under-Voltage Lockout The under-voltage lockout circuit assures that the MOSFET driver outputs and LDO controller remain in the off state whenever the supply voltages drop below set parameters. Normal operation resumes once the supply voltages rise above the set values. APPLICATION INFORMATION Design Example: The following example is a typical application for IRU3048 in current sharing mode. The schematic is Figure 9 on page 12. For Switcher VIN1 = 12V VOUT1 = 3.3V IOUT1 = 4A VIN2 = 5V VOUT2 = 1.8V IOUT2 = 4A DVOUT = 75mV fS = 200KHz For Linear Regulator VIN3 = 3.3V VOUT3 = 2.5V IOUT3 = 2A 6 ---(1) 8 When an external resistor divider is connected to the output as shown in Figure 3. VOUT1 IRU3048 R6 Fb1 R8 Figure 3 - Typical application of the IRU3048 for programming the output voltage. PWM Section Output Voltage Programming Output voltage is programmed by reference voltage and external voltage divider. The Fb1 pin is the inverting input of the error amplifier, which is internally referenced to 1.25V. The divider is ratioed to provide 1.25V at the Fb1 pin when the output is at its desired value. The output voltage is defined by using the following equation: Rev. 1.7 09/12/02 ( RR ) VOUT1 = VREF3 1+ Equation (1) can be rewritten as: ( VV R6 = R8 3 OUT1 REF Will result to: VOUT1=3.3V VREF=1.25V R8=1K, R6=1.64K www.irf.com ) -1 VOUT2=1.8V VREF=1.25V R15=1K, R14=442V 5 IRU3048 If the high value feedback resistors are used, the input bias current of the Fb pin could cause a slight increase in output voltage. The output voltage set point can be more accurate by using precision resistor. Soft-Start Programming The soft-start timing can be programmed by selecting the soft start capacitance value. The start up time of the converter can be calculated by using: tSTART = 75 3 Css (ms) ESR [ ---(2) Where: CSS is the soft-start capacitor (mF) For a start-up time of 7.5ms, the soft-start capacitor will be 0.1mF. Choose a ceramic capacitor at 0.1mF. Boost Supply Vc To drive the high-side switch it is necessary to supply a gate voltage at least 4V greater than the bus voltage. This is achieved by using a charge pump configuration as shown in Figure 9. The capacitor is charged up to approximately twice the bus voltage. A capacitor in the range of 0.1mF to 1mF is generally adequate for most applications. Input Capacitor selection The input filter capacitor should be based on how much ripple the supply can tolerate on the DC input line. The ripple current generated during the on time of control MOSFET should be provided by input capacitor. The RMS value of this ripple is expressed by: IRMS = IOUT D3(1-D) ---(3) Where: D is the Duty Cycle, simply D=VOUT/VIN. IRMS is the RMS value of the input capacitor current. IOUT is the output current for each channel. For VIN1=12V, IOUT1=4A and D1=0.275 Results to: IRMS1=1.78A And for VIN2=5V, IOUT2=4A and D2=0.36 Results to: IRMS2 =1.92A For higher efficiency, a low ESR capacitor is recommended. For VI N 1=12V, choose one Poscap from Sanyo 16TPB47M (16V, 47mF, 70mV, 1.4A) For VIN2=5V, choose one 6TPC150M (6.3V, 150mF, 40mV, 1.9A). 6 Output Capacitor Selection The criteria to select the output capacitor is normally based on the value of the Effective Series Resistance (ESR). In general, the output capacitor must have low enough ESR to meet output ripple and load transient requirements, yet have high enough ESR to satisfy stability requirements. The ESR of the output capacitor is calculated by the following relationship: DVO DIO ---(4) Where: DVO = Output Voltage Ripple DIO = Output Current DVO=75mV and DIO=3A, results to: ESR=25mV The Sanyo TPC series, PosCap capacitor is a good choice. The 6TPC150M 150mF, 6.3V has an ESR 40mV. Selecting two of these capacitors in parallel for each output, results to an ESR of ≅ 20mV which achieves our low ESR goal. The capacitor value must be high enough to absorb the inductor's ripple current. The larger the value of capacitor, the lower will be the output ripple voltage. The resulting output ripple current is smaller then each channel ripple current due to the 1808 phase shift. These currents cancel each other. The cancellation is not the maximum because of the different duty cycle for each channel. Inductor Selection The inductor is selected based on output power, operating frequency and efficiency requirements. Low inductor value causes large ripple current, resulting in the smaller size, but poor efficiency and high output noise. Generally, the selection of inductor value can be reduced to desired maximum ripple current in the inductor (∆i); the optimum point is usually found between 20% and 50% ripple of the output current. For the buck converter, the inductor value for desired operating ripple current can be determined using the following relation: Di 1 VOUT VIN - VOUT = L3 ; Dt = D3 ;D= Dt fS VIN VOUT L = (V IN - VOUT)3 ---(5) VIN3Di3fS Where: VIN = Max Input Voltage ∆t = Turn On Time VOUT = Output Voltage D = Duty Cycle ∆i = Inductor Ripple Current fS = Switching Frequency www.irf.com Rev. 1.7 09/12/02 IRU3048 For Di1=25% of I1, we get L1=9.9mH For Di2=25% of I2, we get: L2=5.7mH The total conduction losses for channel 1 is: PCON1 = 1.1W Panasonic provides a range of inductors in different values and low profile for large currents. For L1 choose ETQP6F102HFA (10.2mH, 4A) For L2 choose ELLATV6R8M (6.8mH, 4A) Power MOSFET Selection The selections criteria to meet power transfer requirements is based on maximum drain-source voltage (V DSS), gate-source drive voltage (V GS), maximum output current, On-resistance RDS(ON) and thermal management. The MOSFET must have a maximum operating voltage (V DSS) exceeding the maximum input voltage (V IN). The gate drive requirement is almost the same for both MOSFETs. Caution should be taken with devices at very low VGS to prevent undesired turn-on of the complementary MOSFET, which results a shoot-through current. The total conduction losses for channel 2 is: PCON2 = 1.1W The control MOSFET contributes to the majority of the switching losses in synchronous Buck converter. The synchronous MOSFET turns on under zero-voltage condition, therefore the turn on losses for synchronous MOSFET can be neglected. With a linear approximation, the total switching loss can be expressed as: VDS(OFF) tr + tf 3 3 ILOAD ---(6) 2 T Where: VDS(OFF) = Drain to Source Voltage at off time tr = Rise Time PSW = tf = Fall Time T = Switching Period ILOAD = Load Current VDS 90% The total power dissipation for MOSFETs includes conduction and switching losses. For the Buck converter the average inductor current is equal to the DC load current. The conduction loss is defined as: 2 PCOND(Upper Switch) = ILOAD 3RDS(ON)3D3q 10% VGS 2 PCOND(Lower Switch) = ILOAD 3RDS(ON)3(1 - D)3q q = RDS(ON) Temperature Dependency td(ON) The total conduction loss is defined as: The RDS(ON) temperature dependency should be considered for the worst case operation. This is typically given in the MOSFET data sheet. Ensure that the conduction losses and switching losses do not exceed the package ratings or violate the overall thermal budget. For this design, IRF7313 is a good choice. These devices provide low on-resistance in a compact SOIC 8Pin package. IRF7313 VDSS = 30V ID = 5.2A @ 708C RDS(ON) = 46mV @ VGS=4.5V q = 1.5 for 1508C (Junction Temperature) Rev. 1.7 09/12/02 td(OFF) tf Figure 4 - Switching time waveforms. PCON(TOTAL)=PCON(Upper Switch)q+PCON(Lower Switch)q The MOSFETs have the following data: tr From IRF7313 data sheet we obtain: IRF7313 tr = 13ns tf = 26ns These values are taken under a certain condition test. For more detail please refer to the IRF7313 data sheet. By using equation (6), we can calculate the switching losses. PSW1 = 187.2mW PSW2 = 78mW www.irf.com 7 IRU3048 VOUT Feedback Compensation The IRU3048 is a voltage mode controller; the control loop is a single voltage feedback path including error amplifier and error comparator. To achieve fast transient response and accurate output regulation, a compensation circuit is necessary. The goal of the compensation network is to provide a closed loop transfer function with the highest 0dB crossing frequency and adequate phase margin (greater than 458). R6 1 2p Figure 5 shows gain and phase of the LC filter. Since we already have 1808 phase shift just from the output filter, the system risks being unstable. Gain Ve C18 VREF R9 Gain(dB) H(s) dB FZ Frequency Figure 6 - Compensation network without local feedback and its asymptotic gain plot. ---(7) Lo3Co Comp E/A R8 The output LC filter introduces a double pole, –40dB/ decade gain slope above its corner resonant frequency, and a total phase lag of 1808 (see Figure 5). The Resonant frequency of the LC filter is expressed as follows: FLC = Fb The transfer function (Ve / VOUT) is given by: ( H(s) = gm 3 ) R8 1 + sR9C18 3 R6 + R8 sC18 ---(9) Phase The (s) indicates that the transfer function varies as a function of frequency. This configuration introduces a gain and zero, expressed by: 08 0dB -40dB/decade |H(s)| = gm 3 FLC Frequency -1808 FLC Frequency FZ = R8 3 R9 R6 3 R8 1 2p 3 R9 3 C18 ---(10) ---(11) Figure 5 - Gain and phase of LC filter. The IRU3048's error amplifier is a differential-input transconductance amplifier. The output is available for DC gain control or AC phase compensation. The E/A can be compensated with or without the use of local feedback. When operated without local feedback the transconductance properties of the E/A become evident and can be used to cancel one of the output filter poles. This will be accomplished with a series RC circuit from Comp1 pin to ground as shown in Figure 6. The ESR zero of the LC filter expressed as follows: FESR = 8 1 2p 3 ESR 3 Co ---(8) The gain is determined by the voltage divider and E/A's transconductance gain. First select the desired zero-crossover frequency (Fo): FO1 > FESR and FO1 [ (1/5 ~ 1/10)3 fS Use the following equation to calculate R4: R9 = 1 VOSC FO13FESR1 R8 + R6 3 3 3 VIN1 FLC12 R8 gm ---(12) Where: VIN1 = Maximum Input Voltage VOSC = Oscillator Ramp Voltage FO1 = Crossover Frequency for the master E/A FESR1 = Zero Frequency of the Output Capacitor FLC1 = Resonant Frequency of Output Filter gm = Error Amplifier Transconductance R8 and R6 = Resistor Dividers for Output Voltage Programming www.irf.com Rev. 1.7 09/12/02 IRU3048 For: VIN1 = 12V VOSC = 1.25V FO1 = 30KHz FESR1 = 26.5KHz VOUT ZIN FLC1 = 2.8KHz R8 = 1K R6 = 1.64K gm = 600mmho C12 C10 R7 R8 Zf This results to R9=46.4KV; Choose R9=46.4KV Fb To cancel one of the LC filter poles, place the zero before the LC filter resonant frequency pole: FZ ≅ 0.75 3 L3 3 CO 2p Ve Comp VREF Gain(dB) 1 E/A R5 FZ ≅ 75%FLC1 C11 R6 H(s) dB ---(13) For: L3 = 10.2mH Co = 300mF Fz = 2.1KHz R9 = 46.4KV FZ1 FZ2 FP2 FP3 Frequency Figure 7 - Compensation network with local feedback and its asymptotic gain plot. Using equations (11) and (13) to calculate C9, we get: In such configuration, the transfer function is given by: C9 = 1630pF; Choose C9 = 1800pF 1Ve VOUT = 1 + Using equations (11),(12) and (13) for Ch2, where: VIN2 = 5V VOSC = 1.25V FO2 = 30KHz FESR2 = 26.5KHz FLC2 = 3.5KHz R15 = 1K R14 = 442V gm = 600mhmo The error amplifier gain is independent of the transconductance under the following condition: gmZf >> 1 We get: R11 = 38.9KV; Choose R11 = 39.2KV C19 = 1554pF; Choose C19 = 1800pF One more capacitor is sometimes added in parallel with C9 and R4. This introduces one more pole which is mainly used to supress the switching noise. The additional pole is given by: 1 2p 3 R9 3 C18 3 CPOLE C18 + CPOLE The pole sets to one half of switching frequency which results in the capacitor CPOLE: 1 1 CPOLE = ≅ p 3 R9 3 fS 1 p 3 R9 3 fS C18 fS For FP << 2 For a general solution for unconditionally stability for any type of output capacitors, in a wide range of ESR values we should implement local feedback with a compensation network. The typically used compensation network for voltage-mode controller is shown in Figure 7. Rev. 1.7 09/12/02 gmZIN >>1 and ---(14) By replacing ZIN and Zf according to figure 7, the transformer function can be expressed as: H(s)= FP = gmZf gmZIN 1 (1+sR7C11)3[1+sC10(R6+R8)] 3 C12C11 sR6(C12+C11) 1+sR7 3(1+sR8C10) C12+C11 [ ( )] As known, transconductance amplifier has high impedance (current source) output, therefore, consider should be taken when loading the E/A output. It may exceed its source/sink output current capability, so that the amplifier will not be able to swing its output voltage over the necessary range. The compensation network has three poles and two zeros and they are expressed as follows: FP2 = FP1 = 0 FP3 = 1 (CC 3C +C ) 2p3R73 FZ1 = 1 2p3R83C10 12 12 11 ≅ 1 2p3R73C12 11 1 2p3R73C11 1 1 FZ2 = 2p3C103(R6 + R8) ≅ 2p3C103R6 www.irf.com 9 IRU3048 Cross Over Frequency: VIN 1 FO1 = R73C103 3 VOSC 2p3Lo3Co 8) Use equation (1) to calculate R5: ---(15) Where: VIN = Maximum Input Voltage VOSC = Oscillator Ramp Voltage Lo = Output Inductor Co = Total Output Capacitors The stability requirement will be satisfied by placing the poles and zeros of the compensation network according to following design rules. The consideration has been taken to satisfy condition 14 regarding transconductance error amplifier. 1) Select the crossover frequency: Fo < FESR and Fo [ (1/10 ~ 1/6)3 fS 2) Select R7, so that R7 >> 2 gm 3) Place first zero before LC’s resonant frequency pole. 4) Place third pole at the half of the switching frequency. fS 2 C12 = 1 2p 3 R7 3 FP3 2p 3 Lo 3 FO 3 Co VOSC 3 R7 VIN ) For: VOUT2 = 2.5V VREF = 1.25V RLOW = 1K VIN3 - VOUT2 IOUT2 For: VIN3 = 3.3V VOUT2 = 2.5V IOUT2 = 2A 1 2p 3 C10 3 FP2 Results to: RDS(ON)(MAX) = 0.4V 1 Check if R8 > gm If R8 is too small, increase R7 and start from step 2. 7) Place second zero around the resonant frequency. FZ2 = FLC 10 Output Voltage Programming Output voltage for LDO is programmed by reference voltage and external voltage divider. The Fb3 pin is the inverting input of the error amplifier, which is internally referenced to 1.25V. The divider is ratioed to provide 1.25V at the Fb3 pin when the output is at its desired value. The output voltage is defined by using the following equation: RHIGH VOUT2 = VREF3 1+ RLOW RDS(ON) = 6) Place second pole at ESR zero. FP2 = FESR R6 = LDO Section LDO Power MOSFET Selection The first step in selecting the power MOSFET for the linear regulator is to select the maximum RDS(ON) based on the input to the dropout voltage and the maximum load current. 5) Place R7 in (15) and calculate C10: R8 = These design rules will give a crossover frequency approximately one-tenth of the switching frequency. The higher the band width, the potentially faster the load transient speed. The gain margin will be large enough to provide high DC-regulation accuracy (typically -5dB to 12dB). The phase margin should be greater than 458 for overall stability. Results to: RHIGH=1K C12 > 50pF If not, change R7 selection. C10 [ VREF 3 R6 VOUT - VREF ( FZ1 ≅ 75% FLC 1 C11 = 2p 3 FZ1 3 R7 FP3 = R5 = Note that since the MOSFET RDS(ON) increases with temperature, this number must be divided by ~1.5 in order to find the RDS(ON)(MAX) at room temperature. The IRLR2703 has a maximum of 0.065V RDS(ON) at room temperature, which meets our requirements. 1 - R8 2p 3 C10 3 FZ2 www.irf.com Rev. 1.7 09/12/02 IRU3048 Layout Consideration The layout is very important when designing high frequency switching converters. Layout will affect noise pickup and can cause a good design to perform with less than expected results. Start to place the power components, make all the connection in the top layer with wide, copper filled areas. The inductor, output capacitor and the MOSFET should be close to each other as possible. This helps to reduce the EMI radiated by the power traces due to the high switching currents through them. Place input capacitor directly to the drain of the high-side MOSFET, to reduce the ESR replace the single input capacitor with two parallel units. The feedback part of the system should be kept away from the inductor and other noise sources, and be placed close to the IC. In multilayer PCB use one layer as power ground plane and have a control circuit ground (analog ground), to which all signals are referenced. The goal is to localize the high current path to a separate loop that does not interfere with the more sensitive analog control function. These two grounds must be connected together on the PC board layout at a single point. TYPICAL APPLICATION 12V to 3.3V @ 4A 12V to 1.8V @ 4A 3.3V to 2.5V @ 2A D1 BAT54S 12V C2 33uF C1 1uF VcH1 Vcc C3 0.1uF VcH2 1/2 of Q2 IRF7313 C11, C12 2x 150uF L3 3.3V @ 4A 10uH C10 470pF 3.3V C9 47uF C7 1uF C6 47uF HDrv1 C8 1uF L1 1uH R2 LDrv1 VOUT3 Q1 IRLR2703 10V 1/2 of Q2 IRF7313 C13 1uF R4 4.7V R6 1.65K PGnd R5 2.5V @ 2A Fb3 1K C14 1uF R7 1K C15 47uF U1 Fb1 IRU3048 HDrv2 C18 1800pF C19 3900pF R9 C17 1uF C16 47uF 1/2 of Q3 IRF7313 L4 Comp1 C21, C22 2x 150uF 1.8V @ 4A 6.8uH C20 470pF 43.2K R11 Comp2 LDrv2 16.2K SS C24 0.1uF R8 1K 1/2 of Q3 IRF7313 C23 1uF R13 4.7V R14 442V Gnd Fb2 R15 1K Figure 8 - Typical application of IRU3048 in an on-board DC-DC converter using a single 12V supply for switcher. Rev. 1.7 09/12/02 www.irf.com 11 IRU3048 DEMO-BOARD APPLICATION 12V to 3.3V @ 4A 5V to 1.8V @ 4A 3.3V to 2.5V @ 2A D1 BAT54S 12V L1 5V C2 33uF C1 1uF C5 1uF VcH1 HDrv1 2.15V R3 LDrv1 3.3V 2.15 V R2 Q1 IRLR2703 1/2 of Q2 IRF7313 1/2 of Q2 IRF7313 Fb3 2.5V @ 2A 1K R7 1K C15 47uF 3.3V @ 4A C10 470pF C13 1uF R4 4.7V R6 1.65K PGnd R5 C11, C12 2x 150uF L4 10.2uH V OUT3 10V C7 1uF C6 47uF VcH2 R1 Vcc C8 1uF C14 1uF C3 0.1uF 1uH C4 33uF C9 47uF L2 1uH U1 Fb1 IRU3048 C17 1uF C16 150uF R8 1K R10 HDrv2 C18 1800pF 2.15V R9 Comp1 46.4K R12 LDrv2 C19 1800pF 1/2 of Q3 IRF7313 R11 2.15V 1/2 of Q3 IRF7313 L3 39.2K C24 0.1uF 1.8V @ 4A 6.8uH C20 470pF C23 1uF R13 4.7V Comp2 SS C21, C22 2x 150uF R14 442V Gnd Fb2 R15 1K Figure 9 - Demo-board application of IRU3048. 12 www.irf.com Rev. 1.7 09/12/02 IRU3048 DEMO-BOARD APPLICATION 12V to 3.3V @ 4A 5V to 1.8V @ 4A 3.3V to 2.5V @ 2A Ref Desig Q1 Q2, Q3 U1 D1 L1, L2 L3 L4 C1,7,8,13, 14,17,23 C2, C4 C3, C24 C5 C9, C15 C10, C20 C18, C19 C6 C11,12,16 21,22 R1,3,10,12 R2 R4, R13 R5,7,8,15 R6 R9 R11 R14 Rev. 1.7 09/12/02 Description MOSFET MOSFET Controller Diode Inductor Inductor Inductor Cap, Ceramic Value Qty Part# 30V, 45mV 1 IRLR2703 30V, 29mV, 5.2A 2 IRF7313 Synchronous PWM 1 IRU3048CF Fast Switching 1 BAT54S 1mH, 2.9A 2 ELL6SH1R0M 6.8mH, 4A 1 ELLATV6R8M 10.2mH, 4A 1 ETQP6F102HFA 1mF, Y5V, 16V 7 ECJ-2VF1C105Z IR IR IR IR Panasonic maco.panasonic.co.jp Panasonic Panasonic Panasonic Cap, Tantalum Cap, Ceramic Cap, Ceramic Cap, Tantalum Cap, Ceramic Cap, Ceramic Cap, Poscap Cap, Poscap 33mF, 16V 0.1mF, Y5V, 25V 1mF, X7R, 25V 47mF, 10V 470pF, X7R, 50V 1800pF, X7R, 50V 47mF, 16V, 70mV 150mF, 6.3V, 40mV 2 2 1 2 2 2 1 5 Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Sanyo sanyo.com/industrial Sanyo Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor 2.15V 10V 4.7V 1K, 1% 1.65K, 1% 46.4K 39.2K 442V, 1% 4 1 2 4 1 1 1 1 ECS-T1CD336R ECJ-2VF1E104Z ECJ-3YB1E105K ECS-T1AD476R ECJ-2VC1H471J ECJ-2VB1H182K 16TPB47M 6TPC150M www.irf.com Manuf Web site (www.) irf.com 13 IRU3048 WAVEFORMS 2A 2A 0A 0A Figure 4 - Transient response @ IOUT = 0 to 2A for 3.3V output. Figure 5 - Transient response @ IOUT = 0 to 2A for 1.8V output. Figure 6 - Transient response @ IOUT = 0 to 2A for 2.5V output. Figure 7 - Output voltage ripple for 3.3V @ 4A. 14 www.irf.com Rev. 1.7 09/12/02 IRU3048 WAVEFORMS Figure 8 - Output voltage ripple for 1.8V @ 4A. Figure 9 - Gate signals for 3.3V output. Ch1: Output current 2A/div. Ch2: Gate signal for control FET 20V/div. Ch3: Gate signal for sync FET 10V/div. V OUT1: 3.3V V OUT2: 1.8V V OUT3: 2.5V Vss Figure 10 - Soft-start voltage Vs. output voltages. Figure 11 - Gate signals for 1.8V output. Ch1: Output current 2A/div. Ch2: Gate signal for control FET 10V/div. Ch3: Gate signal for sync FET 10V/div. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information Data and specifications subject to change without notice. 02/01 Rev. 1.7 09/12/02 www.irf.com 15 IRU3048 (F) TSSOP Package 16-Pin A L Q R1 B 1.0 DIA C R E N M P O PIN NUMBER 1 F D DETAIL A DETAIL A G J H K SYMBOL DESIG A B C D E F G H J K L M N O P Q R R1 MIN 4.30 0.19 4.90 --0.85 0.05 08 0.50 0.09 0.09 16-PIN NOM 0.65 BSC 4.40 6.40 BSC --1.00 1.00 5.00 --0.90 --128 REF 128 REF --1.00 REF 0.60 0.20 ----- MAX 4.50 0.30 5.10 1.10 0.95 0.15 88 0.75 ----- NOTE: ALL MEASUREMENTS ARE IN MILLIMETERS. 16 www.irf.com Rev. 1.7 09/12/02 IRU3048 (S) SOIC Package 16-Pin Surface Mount, Narrow Body H A B C E DETAIL-A PIN NO. 1 L D DETAIL-A 0.386 0.015 x 458 T K I F J G 16-PIN SYMBOL A B C D E F G H I J K L T MIN MAX 9.80 9.98 1.27 BSC 0.51 REF 0.36 0.46 3.81 3.99 1.52 1.72 0.10 0.25 78 BSC 0.19 0.25 5.80 6.20 08 88 0.41 1.27 1.37 1.57 NOTE: ALL MEASUREMENTS ARE IN MILLIMETERS. Rev. 1.7 09/12/02 www.irf.com 17 IRU3048 PACKAGE SHIPMENT METHOD PKG DESIG PACKAGE DESCRIPTION PIN COUNT PARTS PER TUBE PARTS PER REEL T&R Orientation F TSSOP Plastic 16 --- 2500 Fig A S SOIC, Narrow Body 16 50 2500 Fig B 1 1 1 1 1 1 Feed Direction Figure B Feed Direction Figure A IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information Data and specifications subject to change without notice. 02/01 18 www.irf.com Rev. 1.7 09/12/02