TI TPS65166RHAR

TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Compact LCD Bias Supply for TFT-LCD TV Panels
FEATURES
APPLICATIONS
•
•
•
•
•
1
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
8.5V to 14.7V Input Voltage Range
VS Output Voltage Range up to 19V
Boost Converter with 4.2A Switch Current
Step Down Converter with 2.6A Switch Current
and Adjustable Output 2.5V to 3.3V
750kHz Fixed Switching Frequency
Temperature Compensated Negative Supply
High Voltage Stress Test (HVS)
Adjustable Sequencing
Gate Drive Signal for Isolation Switch
Short Circuit Protection
Internal Soft-Start
180° Phase Shift Between Buck and Boost
P2P Short/Open Certified
Optimized Dual Layer PCB Layout
Low EMI
Undervoltage Lockout
Thermal Shutdown
Available in 6×6mm 40 Pin QFN Package
TYPICAL APPLICATION
Vin
12V
Boost
Converter
With HVS
Vs
15V / 2.9A
Buck
Converter
Vlogic
3.3V / 2.4A
Positive
Charge
Pump
VONE
28V / 150mA
Inverting Buck Boost
With
Temperature
Compensation
LCD TV Panel with ASG Technology
DESCRIPTION
The TPS65166 offers a compact power supply
solution to provide all voltages required by a LCD
panel for large TV panel applications running from a
12V supply rail. The device is optimized to support
LCD technology using ASG gate drive circuits.
The device generates all voltage rails for the TFT
LCD bias (VS, VONE, VOFFE, VSS). In addition to that it
includes a step-down converter (Vlogic) to provide the
logic voltage. By pulling the HVS pin high an
implemented high voltage stress test feature
programs the boost converter output voltage Vs to
higher values. The boost converter operates at a
fixed switching frequency of 750kHz. The positive
charge pump is running from the boost converter and
is regulated by an external transistor. A buck-boost
converter provides an adjustable temperature
dependent negative output voltage VOFFE. The
negative output voltage VSS is regulated by a shunt
regulator.
Safety features like overvoltage protection of the
buck-boost input voltage, the boost and buck output
voltage, undervoltage lockout, short circuit protection
of VONE, VOFFE, and Vlogic are included as well as
thermal shutdown.
VOFFE
-22 to -11V / 200mA
Negative Shunt
Regulator
Vss
-7.5V / 100mA
Sequencing
And Logic
Power Good
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION (1) (2)
(1)
(2)
TA
ORDERING
PACKAGE
PACKAGE MARKING
–40°C to 85°C
TPS65166RHAR
6 × 6mm 40 Pin QFN
TPS65166
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
The RHA package is available taped and reeled. Add R suffix to the device type (TPS65166RHAR) to order the device taped and
reeled. The RHA package has quantities of 3000 devices per reel.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted) (1)
VALUE
UNIT
Input voltage range AVIN, VIN1, VIN2, VIN3 (2)
–0.3 to 20
V
Voltage range at SW1, SW2, SW3, SW4, GD, BASE2, RHVS, OS
–0.3 to 20
V
Voltage range at EN1, EN2, HVS
–0.3 to 20
V
Voltage range at COMP, SS, FB1,VSNS, FB2, FB3, FB4, TS, SET, FB5, DLY1, DLY2, PG
–0.3 to 7.0
V
40
V
–9.5 to 0.3
V
Voltage difference VIN3 to SW5
BASE1
ESD rating, Human Body Model
2
kV
ESD rating, Machine Model
200
V
ESD rating, Charged Device Model
700
V
Continuous total power dissipation
See Dissipation Rating Table
Operating junction temperature range, TJ
–40 to 150
°C
Operating ambient temperature range, TA
–40 to 85
°C
Storage temperature range, Tstg
–65 to 150
°C
(1)
(2)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground terminal.
DISSIPATION RATINGS (1)
(1)
PACKAGE
RθJA
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
40 pin QFN
35°C/W
2.8W
1.6W
1.1W
Soldered Power Pad on a standard 2-Layer PCB without vias for thermal pad. See the Texas Instruments Application report (SLMA002)
regarding thermal characteristics of the PowerPAD package.
RECOMMENDED OPERATING CONDITIONS (1)
MIN
TYP
MAX
UNIT
14.7
V
VIN
Input voltage range (AVIN, VIN1, VIN2, VIN3)
8.5
VIN3
Overvoltage protection 15V for buck-boost converter
15
TA
Operating ambient temperature
–40
85
°C
TJ
Operating junction temperature
–40
125
°C
(1)
2
V
Refer to application section for further information
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
ELECTRICAL CHARACTERISTICS
AVIN=VIN1=VIN2=VIN3=12V, EN1=EN2=VIN, VS=15V, Vlogic=3.3V, TA = –40°C to 85°C, typical values are at TA = 25°C
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
VIN
Input voltage range
IQIN
Quiescent current into AVIN, VIN1,2,3
Not switching, FB=FB+5%
8.5
1.2
Isd
Shutdown current into AVIN, VIN1,2,3
EN1=EN2=GND
170
VUVLO
Under-voltage lockout threshold
VIN falling
8.0
8.2
V
VUVLO
Under-voltage lockout threshold
VIN rising
8.2
8.5
V
Thermal shutdown
Temperature rising
150
°C
15
°C
Thermal shutdown hysteresis
14.7
V
mA
µA
LOGIC SIGNALS EN1, EN2, HVS
VIH
High level input voltage
VIN = 8.5V to 14.7V
VIL
Low level input voltage
VIN = 8.5V to 14.7V
II
Input leakage current
EN1=EN2=GND
1.7
V
0.01
0.4
V
0.1
µA
POWER GOOD
VIL
Low level voltage (1)
I(sink) = 500µA
Ilkg
Leakage current
VPG = 5.0V
0.01
0.3
V
0.1
µA
µA
SEQUENCING DLY1, DLY2, and SOFT-START
Ichrg
DLY1, DLY2 charge current
Vthreshold
DLY1, DLY2 threshold voltage
Rdischrg
DLY1, DLY2 discharge resistor
ISS
Soft-start charge current
Vthreshold = 1.24V
4
4.9
6.3
1.21
1.24
1.27
3.2
Vthreshold = 1.24V
V
kΩ
8
10
12
µA
600
750
900
kHz
19
V
19.0
19.5
20
V
1.225
1.24
1.252
V
SWITCHING FREQUENCY
fs
Switching frequency
BOOST CONVERTER (Vs)
Vs
Output voltage range
Vswovp
Switch overvoltage protection
VFB1
Feedback regulation voltage
IFB1
Feedback input bias current
VFB1 = 1.24V
10
100
nA
RDS(on)
N-MOSFET on-resistance
ISW = 500mA
120
170
mΩ
ILIM
N-MOSFET switch current limit
5.2
6.2
A
Ileak
Switch leakage current
1
10
µA
ton
Minimum on time
Vs rising
4.2
Vsw = 15V
80
Line regulation
8.5V ≤ VIN ≤ 14.7V, Iout = 1mA
Load regulation
1mA ≤ Iout ≤ 2.0A
ns
0.006
%/V
0.1
%/A
GATE DRIVE (GD) AND BOOST CONVERTER PROTECTION
VGDM
VIN – VGD (2)
VIN = 12V, GD pulled down
I(GD)
Gate drive sink current
EN2 = high
10
R(GD)
Gate drive internal pull up resistance
10
kΩ
ton
Gate on time during short circuit
FB1 < 100mV
1.4
ms
5
6
7
V
µA
BUCK CONVERTER (Vlogic)
Vlogic
Output voltage range
2.2
VFB2
Feedback regulation voltage
FB2 connected to resistor divider,
Iload = 10mA
IFB2
Feedback input bias current
VFB2 = 1.24V
RDS(on)
N-MOSFET on-resistance
Isw3, Isw4 = 1.5A
(1)
(2)
1.215
4.0
V
1.24
1.265
V
10
100
nA
150
250
mΩ
PG goes high impedance once Vs and VONE are in regulation.
GD goes to VIN – VGD once the boost converter Vs is enabled.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
3
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
AVIN=VIN1=VIN2=VIN3=12V, EN1=EN2=VIN, VS=15V, Vlogic=3.3V, TA = –40°C to 85°C, typical values are at TA = 25°C
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
2.6
3.4
4.2
UNIT
ILIM
N-MOSFET switch current limit
Ileak
Switch leakage current
Vsw = 0V
Line regulation
8.5V ≤ VIN ≤ 14.7V, Iout = 1mA
0.006
%/V
1mA ≤ Iout ≤ 100mA
0.042
%/mA
100mA ≤ Iout ≤ 2.5A
0.06
%/A
Load regulation
A
µA
1
NEGATIVE SHUNT REGULATOR (Vss)
VBase1
Base1 voltage range
Transistor leakage maximum 5µA
IBase1
Base1 drive source current
VFB3 = VFB3nominal – 5%
VFB3
Feedback regulation voltage
IFB3
Feedback input bias current
VFB3 = 1.24V
Line regulation
8.5V ≤ VIN ≤ 14.7V, Iout = 1mA
Load regulation
1mA ≤ Iout ≤ 100mA
–9.5
0.3
5
–5%
V
mA
0.75 ×
Vlogic
5%
10
100
V
nA
0.006
%/V
0.0004
%/mA
NEGATIVE BUCK BOOST CONVERTER (VOFFE)
Vovp
VIN3 overvoltage protection
VOFFE
Adjustable output voltage range
RDS(on)
P-MOSFET on resistance
ILIM
P-MOSFET current limit
15
ISW5 at current limit
Regulation accuracy upper limit
VTS = 1V, VSET = 1.9V
Regulation accuracy
VTS = 1V, VSET = 2.4V
Regulation accuracy lower limit
VTS = 0.7V, VSET = 2.4V
IFB5
Feedback input bias current
ITS
ISET
VFB5
V
–22
0.9
1.1
1.4
1.8
1.9
-5
V
1.6
Ω
A
2.0
V
V
1.9
2
2.1
1.57
1.65
1.73
V
VFB5 = 2V
10
100
nA
TS input bias current
VTS = 1V
10
100
nA
SET input bias current
VSET = 3V
3
5
Line regulation
8.5V ≤ VIN ≤ 14.7V, Iout = 1mA
Load regulation
1mA ≤ Iout ≤ 200mA, VOFFE = –11V
µA
0.003
%/V
0.0005
%/mA
POSITIVE CHARGE PUMP (VONE)
IBase2
Base2 drive sink current
VFB4 = VFB4nominal-5%
Base2 drive sink current (SC-Mode)
VFB4 = GND
8
14
40
50
70
µA
20
V
1.18
1.24
1.30
V
100
nA
VBase2
Base drive voltage range
VFB4
Feedback regulation voltage
IFB4
Feedback input bias current
VFB4 = 1.24V
10
Line regulation
8.5V ≤ VIN ≤ 14.7V, Iout = 1mA
0.9
Load regulation
1mA ≤ Iout ≤ 150mA, VOFFE = –11V
mA
%/V
0.004
%/mA
HIGH VOLTAGE STRESS TEST (HVS), RHVS
RHVS
RHVS pull down resistance
HVS = high, IHVS = 500µA
IRHVS
RHVS leakage current
HVS = low, VRHVS = 5V
4
Submit Documentation Feedback
350
450
550
Ω
100
nA
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
DEVICE INFORMATION
PACKAGE
PGND1
PGND2
SW1
SW2
OS
VL+
COMP
FB1
RHVS
VIN3
40 Pin 6mm x 6mm QFN
(Top View)
40
39
38
37
36
35
34
33
32
31
GD
1
30
SW 5
AVIN
2
29
NC
VIN1
3
28
NC
VIN2
4
27
FB 5
NC
5
26
TS
SW3
6
25
SET
SW4
7
24
AGND/VL-
NC
8
23
NC
VSNS
9
22
NC
21
BASE2
14
15
16
17
18
EN2
HVS
FB3
SS
BASE1
19
20
FB4
13
DLY2
12
EN1
PG
10
11
DLY1
FB 2
Exposed
Thermal Die
*
NOTE: The thermally enhance Power Pad is connected to GND
PIN FUNCTIONS
PIN
NAME
GD
AVIN
VIN1, VIN2
NC
SW3, SW4
NO.
I/O
DESCRIPTION
1
I
Gate drive pin for the external isolation MOSFET.
2
I
Input voltage supply pin for the analog circuit.
3,4
I
Input supply for the buck converter generating Vlogic
5
6,7
Not connected
O
Switch pin for the buck converter generating Vlogic
NC
8
VSNS
9
I
Not connected
Reference voltage input for the buck-boost and negative shunt regulator
FB2
10
I
Feedback pin for the buck converter.
PG
11
I
Power good output latched high when VS and VONE are in regulation
DLY1
12
O
Delay pin EN2 high to enable boost converter VS
EN1
13
I
Enable of the buck converter Vlogic
EN2
14
I
Enable of the negative supplies VSS and VOFFE, enable DLY1 and DLY2
HVS
15
I
Logic pin to enable high voltage stress test. This allows programming the boost converter VS to a
higher voltage
FB3
16
I
Feedback of the negative supply VSS
SS
17
O
Soft-start for the boost converter VS
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
5
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
PIN FUNCTIONS (continued)
PIN
NAME
NO.
I/O
DESCRIPTION
BASE1
18
O
Base drive of the external npn transistor for the negative supply VSS
DLY2
19
O
Delay pin EN2 high to enable charge pump VONE
FB4
20
I
Feedback for the positive supply VONE
BASE2
21
I
Base drive of the external pnp transistor for the positive charge pump VONE
NC
22, 23
Not connected
AGND/VL-
24
SET
25
I
Analog ground and connection of the bypass capacitor of VLInput pin for the reference voltage to set the higher limit for the temperature compensation for
VOFFE
TS
26
I
Input pin for the NTC temperature sensor
FB5
27
I
Feedback pin for the negative buck-boost converter VOFFE
NC
28, 29
Not connected
SW5
30
O
Switch pin for the negative buck-boost converter generating VOFFE
VIN3
31
I
Input supply for the buck-boost converter generating VOFFE
RHVS
32
I
This pin is pulled low when HVS is high. The resistor connected to this pin sets the boost
converter output voltage when HVS is pulled high
FB1
33
I
Feedback for the boost converter VS
COMP
34
O
Compensation pin for the boost converter
VL+
35
O
Output of the internal logic regulator. Connect a capacitor between this pin and AGND/VL-
OS
36
I
Connect this pin to the boost converter output for overvoltage protection
SW1, SW2
37, 38
I
Switch pin for the boost converter and the positive charge pump VONE
PGND1,
PGND2
39, 40
6
Power ground for the boost converter VS
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Functional Block Diagram
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
7
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
8
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
TYPICAL CHARACTERISTICS
TABLE OF GRAPHS
FIGURE
Start-up Sequence
Startup sequencing
Figure 1
Startup sequencing
Figure 2
Boost Converter
Soft-start boost converter
Figure 3
Efficiency boost converter
vs load current
Figure 4
PWM operation
at nominal load current
Figure 5
PWM operation
at light load current
Figure 6
Load transient response boost converter
Figure 7
Overvoltage protection
Figure 8
Buck Converter
Efficiency buck converter
vs load current
Soft-start buck converter
Figure 9
Figure 10
PWM operation
at nominal load current
Figure 11
PWM operation
at light load current
Figure 12
Load transient response buck converter
Figure 13
180° Phase shift between boost and buck converter
Figure 14
Buck Boost Converter
Efficiency buck boost converter
vs load current
Figure 15
PWM operation
at nominal load current
Figure 16
Load transient response buck boost converter
PWM operation
Figure 17
at light load current
Figure 18
Load transient response positive charge pump
boost voltage Vs = 15V
Figure 19
Load transient response positive charge pump
boost voltage Vs = 18V
Figure 20
Charge Pump
Shunt Regulator
Load transient response negative shunt regulator
Figure 21
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
9
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
10
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
11
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
12
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
13
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
14
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Figure 21.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
15
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
APPLICATION INFORMATION
Figure 22. Control Block TPS65166
Thermal Shutdown
A thermal shutdown is implemented to prevent damages because of excessive heat and power dissipation. Once
a temperature of typlically 150°C is exceeded the device enters shutdown. It enables again if the temperature
drops below the threshold temperature of typically 135 °C and does normal startup.
Undervoltage Lockout
To avoid mis-operation of the device at low input voltages an undervoltage lockout is included, which shuts down
the device at voltages lower than typically 8.0V.
Short Circuit Protection
The positive charge pump controller VONE will run with reduced current (typ. 50 µA) and disables the boost
converter if short circuit is detected (FB4 falls below 100 mV). An exception is made at startup. If VONE has once
passed the short level threshold (FB4 is above 100 mV), the boost converter will not be disabled until Power
Good of VONE has been detected. In case there is already a short when the device is activated the charge pump
controller VONE will run with reduced current and the boost converter will not start until the short is removed and
VONE passes the short level threshold.
16
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
The buck converter detects a short circuit if FB2 falls below 400 mV and the whole device except the buck
converter itself is shut down as if EN2 would be disabled. The switching frequency of the buck converter is
reduced to 1/4th of the normal operation frequency. If the short is removed the buck converter will start operation
again and the whole device auto recovers to normal operation by doing startup sequencing as if EN2 would be
enabled.
The negative buck boost converter VOFFE has a short circuit protection where the switch current is limited to
typically 300 mA and switching frequency is reduced to about 150 kHz. A short is detected if VOFFE rises above
-3 V.
The shunt regulator Vss has no short circuit protection.
Start-Up Sequencing
The device has adjustable start-up sequencing to provide correct sequencing as required by the display.
VIN
EN1
Vlogic
EN2
VSS
VOFFE
GD
GD ok
DLY1
DLY2 < DLY1
VS
DLY2
VONE
DLY2 > DLY1
Power Good for
Scan Drive IC
DLY2
PG
Figure 23. Power Up Sequencing
EN1 enables the buck converter.
EN2 enables the negative buck boost converter VOFFE and Vss at the same time. DLY1 sets the delay time for the
boost converter Vs and DLY2 sets the delay time for VONE. VONE does not start until DLY1 is elapsed. For
simultaneous startup of Vs and VONE, DLY2 should be set to 0 by not connecting the DLY2 pin. Once VS and
VONE are in regulation, PG goes high impedance to enable the scan driver IC.
Power Good Output
The power good output PG is an open drain output with typically 450Ω resistance and requires a pull-up resistor
to the 3.3V rail. The power good goes high impedance when the Vs and VONE voltage rails are in regulation and
provides an enable signal for the external scan driver IC. Once power good is high impedance, the signal is
latched until Vs or VONE detect a short circuit.
The resulting maximum PG voltage if PG is low is dependent on R22 connection voltage (Vlogic) and R22 value.
To calculate maximum resulting PG voltage for power bad signal use following formula:
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
17
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
VPG _ low =
450W ´ Vlog ic
450W + R 22
(1)
The resulting PG voltage if PG pin is high impedance is dependent on R22 connection voltage (Vlogic), R22 value
and output current Iout of PG node. The output current is flowing to the external scan driver. Assuming a
maximum switch leakage current of 1µA the minimum PG output voltage can be calculated as following:
VPG _ high = Vlog ic - R 22 ´ (1m A + Iout )
(2)
Recommended are R22 values between 5kΩ and 500kΩ. Typical value for R22 is 10kΩ.
Setting the Delay Times DLY1, DLY2
Connecting an external capacitor to the DLY1 and DLY2 pins sets the delay time. The capacitor is charged with
a constant current source of typically 5µA. The delay time is terminated when the capacitor voltage has reached
the threshold voltage of Vth = 1.24V. If no capacitor is set, the delay time is zero. The external capacitors can be
calculated as follows:
5 mA ´ DLY 5 mA ´ DLY
CDLY =
=
, with DLY = Desired delay time
Vth
1.24 V
(3)
Example for setting a delay time of 2.5ms:
5 mA ´ 2.5 ms
CDLY =
= 10.1 nF Þ CDLY = 10 nF
1.24 V
(4)
Boost Converter
The non-synchronous current mode boost converter operates in Pulse Width Modulation (PWM) operation with a
fixed frequency of 750 kHz. For maximum flexibility and stability with different external components the converter
uses external loop compensation. At start up the boost converter starts with an externally adjustable soft-start.
The boost converter provides the supply voltage for the LCD source driver as well as for the charge pump
regulator VONE. This needs to be taken into account when defining the output current requirements for the boost
converter. No feed-forward capacitor is needed for proper operation.
18
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
SW1
SW2
Switch
GD
Current Sampling
&
Slope Compensation
IGD
10kW
6V
AVIN
VL
ISS
Current Limit
&
Softstart
SS
COMP
Error
Amplifier
Comparator
D
N-MOS
Control Logic
FB1
S
PGND1
1.24V
Overvoltage
Comparator
PGND2
750kHz
Oscillator
1.24V + 3%
OS
Overvoltage
Comperator
Short circuit
Comparator
1.24V
100 mV
HVS
S
D
RHVS
450W
Figure 24. Boost Converter Block Diagram
Soft-Start (Boost Converter)
To avoid high inrush current during start-up an internal soft-start is implemented. The soft-start time is set by an
external capacitor connected to the SS pin. The capacitor is charged with a constant current of typically 10µA,
which increases the voltage at the SS pin. The internal switch current limit is proportional to the SS pin voltage
and rises with rising voltage until VS is in regulation or the maximum current limit is reached. The larger the
soft-start capacitor value the longer the soft-start time. For a 100nF capacitor at the SS pin, the current limit is
reached after 0.9ms. An estimation of the current limit slope ΔIinductor and CSS capacitor can be made by the
following formulas.
D Iinductor
0.43
mA 2
´
=
Dt
CSS
V
CSS =
0.43 ´ D t
mA 2
´
D Iinductor
V
(5)
Compensation (Boost Converter)
The regulator loop can be compensated by adjusting the external components connected to the COMP pin. The
typical value of R4 = 39kΩ and C5 = 1nF is appropriate for most applications. The below formula calculates at
what frequency the resistor R4 increases the high frequency gain.
fZ =
1
2 ´ p ´ R 4 ´ C5
(6)
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
19
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
Gate Drive Pin (GD) and Isolation Switch Selection
The external isolation switch disconnects the boost converter once the device is turned off. If the boost converter
is enabled by EN2 and the delay time set by DLY1 passed by, the gate pin GD is pulled low by an internal 10 µA
current sink to minimize inrush current until the Gate-Source voltage is clamped at about VIN -6 V. An internal 10
kΩ pull up resistor to VIN is connected to GD to open the isolation switch if the Gate Drive is disabled. Using a
gate drain capacitor of typically 1 nF allows to increase the turn on time of the MOSFET for further inrush current
minimization. If the boost feedback voltage falls below 100mV for more than 1.4 ms, GD is pulled high and the
boost converter shuts down. The device does not recover automatically from shut down but Enable or
unvervoltage lockout must be toggled. Using this configuration allows to optimize the solution to specific
application requirement and different MOSFETs can be used. A standard P-Channel MOSFET with a current
rating close to the maximal used switch current of the boost converter is sufficient. The worst case power
dissipation of the isolation switch is the maximal used switch current x RDS(on) of the MOSFET. A standard
SOT23 package or similar is able to provide sufficient power dissipation.
Table 1. Isolation Switch Selection
COMPONENT SUPPLIER
CURRENT RATING
Vishay Siliconix Si3443CDV
4.7 A / 60 mΩ
Vishay Siliconix Si3433DS
6 A / 38 mΩ
International Rectifier IRLML6402
3.7 A / 65 mΩ
Switch
GD
I (GD)
6V
R (GD)
Vin
Figure 25. GD Drive
High Voltage Stress Test (HVS)
The device has a high voltage stress test. This allows programming the boost converter output voltage VS higher
by the resistor connected to RHVS once HVS is pulled high. With HVS = high the RHVS pin is switched to GND.
The resistors R2 and R3 are connected parallel and therefore the overall resistance is reduced. This changes the
output voltage during the High Voltage Stress Test to a higher value:
R1 + R2||R3
R1 + R2||R3
VsHVS = VFB1
= 1.24V
R2||R3
R2||R3
(7)
R3 =
R1 ´ R2
æ VsHV S
ö
- 1÷ ´ R2 - R1
ç
è VFB 1
ø
=
R1 ´ R2
æ VsHVS
ö
- 1÷ ´ R2 - R1
ç
è 1.24V
ø
(8)
With:
VsHVS = Boost converter output voltage with HVS high
Overvoltage Protection
The boost converter has two overvoltage protection mechanisms for the switch. Vs is monitored with an
overvoltage protection comparator on the OS pin and as soon as 19.5V typical is reached, the boost converter
stops switching. The converter also detects overvoltage if the feedback voltage at the feedback pin FB1 is 3%
above the typical regulation voltage of 1.24V, which stops switching. The converter starts switching again if the
output voltage falls below the overvoltage thresholds.
20
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Input Capacitor Selection
For good input voltage filtering, low ESR ceramic capacitors are recommended. All input voltages (AVIN, VIN1,
2, 3) are shorted internally. It is recommended to short AVIN, VIN1, and VIN2 externally on the PCB by a thick
conducting path to avoid high currents between the VIN pins inside the device and to place two 10µF input
capacitors as close as possible to these pins. Another 10µF input capacitor should be placed close to VIN3. For
better input voltage filtering the input capacitor values can be increased. If it is not possible to place the 10µF
capacitors close to the device, it is recommended to add an additional 1µF or 4.7µF capacitor which should be
placed next to the input pins. To reduce power losses at the external isolation switch, a filter capacitor C3 at the
input terminal of the inductor is required. To minimize possible audible noise problems, two 10µF capacitors in
parallel are recommended. More capacitance further reduces the ripple current across the isolation switch. See
Table 2 for input capacitor selection.
Table 2. Input Capacitor Selection
CAPACITOR
COMPONENT SUPPLIER
10µF/16V
Murata, GRM31CR71C106KAC7
10µF/16V
Taiyo Yuden, EMK325BJ106MN
10µF/16V
Murata, GRM31CR61C106KA88
Boost Converter Design Procedure
The first step in the design procedure is to verify whether the maximum possible output current of the boost
converter supports the specific application requirements. To simplify the calculation, the fastest approach is to
estimate the converter efficiency by taking the efficiency numbers from the provided efficiency curves or to use a
worst case assumption for the expected efficiency, e.g., 90%. The calculation must be made with the minimum
assumed input voltage where peak switch current is the highest. The inductor and external Schottky diode has to
be able to handle this current.
V ´ h
1. Converter Duty Cycle:
D = 1 - in
Vout
V ´ Dö
æ
2. Maximum output current: Iout = ç Iswpeak - in
÷ ´ (1- D)
2fs ´ L ø
è
V ´ D Iout
3. Peak switch current:
Iswpeak = in
+
2fs ´ L 1- D
(9)
With,
Iswpeak = Converter peak switch current (minimum switch current limit = 4.2 A)
fs = Converter switching frequency (typical 750 kHz)
L = Selected inductor value
η = Estimated converter efficiency (use the number from the efficiency curves or 0.9 as an assumption)
Inductor Selection (Boost Converter)
The boost converter is able to operate with 6.8µH to 15µH inductors, a 10µH inductor is typical. The main
parameter for inductor selection is the saturation current of the inductor, which should be higher than the peak
switch current as calculated in the Design Procedure section with additional margin to cover for heavy load
transients. The alternative more conservative approach is to choose an inductor with saturation current at least
as high as the minimum switch current limit of 4.2A. Another important parameter is the inductor dc resistance.
Usually the lower the dc resistance the higher the efficiency. For a boost converter where the inductor is the
energy storage element, the type and core material of the inductor influences the efficiency as well. The
efficiency difference among inductors can vary up to 10%. Possible inductors are shown in Table 3.
Table 3. Inductor Selection Boost Converter
INDUCTOR VALUE
COMPONENT SUPLIER
SIZE (L×W×H mm)
Isat/DCR
10 µH
Sumida CDRH103R
10.3 × 10.5 × 3.1
3.2 A/45 mΩ
10 µH
Sumida CDRH8D38
8.3 × 8.3 × 4.0
3 A/38 mΩ
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
21
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
Table 3. Inductor Selection Boost Converter (continued)
INDUCTOR VALUE
COMPONENT SUPLIER
SIZE (L×W×H mm)
Isat/DCR
10 µH
Sumida CDRH104R
10.3 × 10.5 × 4.0
4.4 A/26 mΩ
10 µH
Sumida CDRH8D43
8.3 × 8.3 × 4.5
4 A/29 mΩ
Rectifier Diode Selection (Boost Converter)
To achieve high efficiency a Schottky diode should be used. The reverse voltage rating should be higher than the
maximum output voltage of the boost converter. The average rectified forward current Iavg, the Schottky diode
needs to be rated for, is equal to the output current Iout.
Iavg = Iout
(10)
Usually a Schottky diode with 2A maximum average rectified forward current rating is sufficient for most
applications. The Schottky rectifier can be selected with lower forward current capability depending on the output
current Iout, but has to be able to dissipate the power. The dissipated power is calculated according to the the
following equation:
PD = Iavg × Vforward
(11)
Table 4. Rectifier Diode Selection (Boost Converter)
Vr/Iavg
Vforward
RθJA
SIZE
COMPONENT SUPPLIER
20V/2A
0.44V at 2A
25°C/W
SMB
B220, DIODES Incorporated
20V/2A
0.44V at 2A
75°C/W
SMB
SL22, Vishay Semiconductor
20V/3A
0.44V at 3A
46°C/W
SMC
MBRS320, International Rectifier
Output Capacitor Selection (Boost Converter)
For the best output voltage filtering, low ESR ceramic output capacitors are recommended. Three 22µF or six
10µF ceramic output capacitors with sufficient voltage rating in parallel are adequate for most applications.
Additional capacitors can be added to improve the load transient regulation. See Table 5 for output capacitor
selection.
Table 5. Output Capacitor Selection (Boost Converter)
CAPACITOR
COMPONENT SUPPLIER
22µF/25V
Murata, GRM32ER61E226KE15
10µF/25V
Murata, GRM31CR61E106KA12
10µF/50V
Taiyo Yuden, UMK325BJ106MM
Setting the Output Voltage (Boost Converter)
The output voltage is set by an external resistor divider. A minimum current of 100µA through the feedback
divider provides good accuracy and noise covering. The resistors are calculated as:
R1 ö
R1 ö
æ
æ
Vs = VFB1 ´ ç 1+
÷ = 1.24 V ´ ç 1+ R2 ÷
R2
è
ø
è
ø
R2 =
VFB1
100 mA
=
1.24 V
» 12 kW
100 mA
(13)
æ V
ö
æ Vs
ö
R1 = R2 ´ ç s - 1÷ = R2 ´ ç
- 1÷
è 1.24 V
ø
è VFB1
ø
22
(12)
Submit Documentation Feedback
(14)
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Buck Converter
VIN1
S
D
The non-synchronous current mode buck converter operates at fixed frequency PWM operation. The converter
drives an internal N-channel MOSFET switch with an internal bootstrap capacitor. The output voltage can be set
between 2.5V and 3.3V by an external feedback divider. If the feedback voltage FB2 is 15% above the reference
voltage of 1.24V the converter stops switching and starts switching again if the FB2 voltage falls below the
threshold. For 3.3V output voltage the overvoltage lockout is approximately 3.8 V.
SW3
N-MOS
Current Sampling
&
Slope Compenation
VIN2
Current
Comparator
SW4
Error
Amplifier
Control
Logic
1.24 V
FB2
Current Limit
&
Softstart
Overvoltage
Comparator
Clock
1.24 V
+ 15%
Clock / 2
0.8 V
Clock / 4
0.4 V
Logic
750 kHz
Oscillator
Clock selection for short circuit
and Softstart
Figure 26. Buck Converter Block Diagram
Soft-Start (Buck Converter)
To avoid high inrush current during start-up, an internal soft-start is implemented. When the buck converter is
enabled, its current limit is reduced and it slowly rises (1ms to 2ms) to the switch current limit. For further inrush
current limitation, the switching frequency is reduced to 1/4 of the switching frequency fs until the feedback
voltage FB2 reaches 0.4V, then the switching frequency is set to 1/2 of fs until FB2 reaches 0.8V when the full
switching frequency fs (750kHz) is applied. See the internal Block diagram (Figure 26) for further explanation.
The soft-start is typically completed in 1ms to 2ms.
Buck Converter Design Procedure
The first step in the design procedure is to verify whether the maximum possible output current of the buck
converter supports the specific application requirements. To simplify the calculation, the fastest approach is to
estimate the converter efficiency by taking the efficiency numbers from the provided efficiency curves or to use a
worst case assumption for the expected efficiency, e.g., 80%. The calculation must be for the maximum assumed
input voltage where the peak switch current is the highest. The inductor and external Schottky diode have to be
able to handle this current.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
23
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
1. Converter Duty Cycle:
D=
Vout
Vin ´ h
2. Maximum output current: Iout = Iswpeak -
3. Peak switch current:
Iswpeak = Iout +
Vin ´ (1 - D)
2fs×L
Vin ´ (1- D)
2fs ´ L
´D
´D
(15)
With;
Iswpeak = Converter peak switch current (minimum switch current limit = 2.6A)
fs = Converter switching frequency (typical 750kHz)
L = Selected inductor value
η = Estimated converter efficiency (use the number from the efficiency curves or 0.8 as an assumption)
Inductor Selection (Buck Converter)
The buck converter is able to operate with 6.8µH to 15µH inductors, a 10µH inductor is typical. The main
parameter for inductor selection is the saturation current of the inductor which should be higher than the
maximum output current plus the inductor ripple current as calculated in the Design Procedure section. The
highest inductor current occurs at maximum VIN. The alternative more conservative approach is to choose an
inductor with saturation current at least as high as the minimum switch current limit of 2.6A. Another important
parameter is the inductor dc resistance. Usually the lower the dc resistance the higher the efficiency; the type
and core material of the inductor influences the efficiency as well. The efficiency difference among inductors can
vary up to 10%. Possible inductors are shown in Table 6.
Table 6. Inductor Selection Buck Converter
INDUCTOR VALUE
COMPONENT SUPPLIER
SIZE (L×W×H mm)
Isat/DCR
10µH
Sumida CDRH6D38
7.0 × 7.0 × 4.0
2.0A/28mΩ
10µH
Sumida CDRH8D28
8.3 × 8.3 × 3
2.5A/36mΩ
10µH
Sumida CDRH103R
10.3 × 10.5 × 3.1
3.2A/45mΩ
Rectifier Diode Selection (Buck Converter)
To achieve high efficiency, a Schottky diode should be used. The reverse voltage rating should be higher than
the maximum output voltage of the buck converter. The average rectified forward current Iavg, the Schottky diode
needs to be rated for, is calculated as the off time of the buck converter times the output current.
Iavg = Iout × (1 – D)
(16)
Usually a Schottky diode with a 2A maximum average rectified forward current rating is sufficient for most
applications. The Schottky rectifier can be selected with lower forward current capability depending on the output
current Iout, but has to be able to dissipate the power. The dissipated power is the average rectified forward
current times the diode forward voltage. The efficiency rises with lower forward voltage.
PD = Iavg × Vforward
(17)
Table 7. Rectifier Diode Selection (Buck Converter)
24
Vr/Iavg
Vforward
RθJA
SIZE
COMPONENT SUPPLIER
20V/2A
0.44V at 2A
25°C/W
SMA
B220A, DIODES Incorporated
20V/2A
0.5V at 2A
75°C/W
SMB
SS22, Vishay Semiconductor
20V/3A
0.5V at 3A
50°C/W
SMA
B320A, DIODES Incorporated
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Output Capacitor Selection (Buck Converter)
For best output voltage filtering, low ESR ceramic output capacitors are recommended. Two 22µF or four 10µF
ceramic output capacitors with sufficient voltage rating in parallel are adequate for most applications. Additional
capacitors can be added to improve the load transient regulation. See Table 8 for output capacitor selection.
Table 8. Output Capacitor Selection (Buck Converter)
CAPACITOR
COMPONENT SUPPLIER
22µF/6.3V
Murata, GRM31CR60J226KE19
10µF/6.3V
Murata, GRM21BR70J106KE76
47µF/6.3V
Murata, GRM32ER60J476ME20
10µF/6.3V
Taiyo Yuden, JWK212BJ106MD
Setting the Output Voltage (Buck Converter)
The output voltage is set by an external resistor divider. R6 should be chosen in the range of 0.5kΩ to 4.7kΩ. For
good noise covering and accuracy the lower feedback resistor R6 is selected to obtain at least a 250µA minimum
load current.
æ R5 ö
æ R5 ö
Vlogic = VFB2 ´ ç 1+
÷ = 1.24 V ´ ç 1+ R6 ÷
R6
è
ø
è
ø
R6 =
VFB2
(18)
1.24 V
» 1.2 k W
1 mA
=
1mA
(19)
æ Vlogic
ö
æ Vlogic
ö
- 1÷ = R6 ´ ç
- 1÷
R5 = R6 ´ ç
çV
÷
ç 1.24 V
÷
è FB2
ø
è
ø
(20)
Negative Buck-Boost Converter VOFFE, Temperature Compensation
The non-synchronous constant off-time current mode buck-boost converter generates the negative VOFFE voltage
rail. This output rail is required to power the scan driver. The output voltage is temperature compensated and
fully adjustable from –22V to –5V. The external resistor divider on pins FB5 and SET allow programming high
and low voltage levels. The graph below shows the output voltage versus temperature in °C and series resistor
R19 (5kΩ to 7.5kΩ). NTC (22kΩ) and R18 (30kΩ) define the slope of the curve, R19 allows selection of the
temperature point where temperature compensation begins and ends. The converter is compensated internally,
for further stabilization the feed-forward capacitor C22 can be chosen between 100pF and 2nF. Soft-start is also
realized with this capacitor. The larger the capacitor value the longer the soft-start time. The recommended C22
value is 1nF.
-10 V
-11 V
7.5 kW
7 kW
-12 V
-14 V
-15 V
-16 V
Vref 3.3 V
6.5 kW
-13 V
Slope of curve
adjusted by
NTC and R18
6 kW
VOFFE_max set by
resistor network FB5
and SET
5.5 kW
5 kW
R18
NTC
-17 V
TS
-18 V
-19 V
R19
-20 V
VOFFE_min set by
resistor network FB5
-21 V
-22 V
-23 V
-10ºC
0ºC
10ºC
20ºC
30ºC
40ºC
50ºC
Figure 27. VOFFE Temperature Compensation
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
25
TPS65166
S
VIN3
D
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
SW5
P-MOS
Overvoltage
Protection
Short circuit
Protection
Current
Limit
Current Mode
Control
SET
Current
Comparator
2x
TS
Error
Amplifier
V ref/ 2
clamp
FB5
Figure 28. Buck-Boost Converter Block Diagram
Setting the Minimal and Maximal Output Voltage, VOFFE
Keep in mind that VOFFE has a negative value, while Vlogic and VSET have positive values:
VOFFE_min =
Vlogic
2
æ R21 ö
æ R21 ö
´ ç 1÷ = 1.65 V ´ ç 1- R20 ÷ , select R21 about 1 MW to achieve good soft-start.
R20
è
ø
è
ø
(21)
R20 =
Vlogic ´ R21
Vlogic - 2×VOFFE_min
=
3.3 V ´ R21
3.3 V - 2 ´ VOFFE_min
VOFFE_max = VSET - (Vlogic - VSET ) ´
VSET =
R21
R21
= VSET - (3.3V - VSET ) ´
, VSET is calculated below.
R20
R20
VOFFE_max ´ R20 + Vlogic ´ R21
VSET = Vlogic ´
R20 + R21
(22)
=
(23)
VOFFE_max ´ R20 + 3.3 V ´ R21
R20 + R21
(24)
R17
R17
= 3.3 V ´
, select R17 between 1 kW and 20 kW for good accuracy.
R16 + R17
R16 + R17
(25)
æ Vlogic
ö
æ 3.3V
ö
- 1÷÷ = R17 ´ ç
- 1÷
R16 = R17 ´ çç
V
V
è SET
ø
è SET
ø
(26)
Setting the Start and End Temperature of the Compensation
The resistance of a NTC termistor decreases nonlinearly with rising temperature.
RNTC (T) = R T0 ´
æ 1
1ö
- B×çç
- ÷÷
T0
Tø
è
e
(27)
Where,
RT0 is the resistance at an absolute temperature T0 in Kelvin (normally 25°C)
T is the temperature in Kelvin (°C + 273.15 K/°C)
B is a material constant
26
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
The NTC termistor manufacturer provides the above parameters. Typically a 22kΩ NTC is used. Table 9
provides a suggestion for NTCs.
Table 9. Negative Termistor Selection
RESISTANCE (25°C)
B CONSTANT
COMPONENT SUPPLIER
COMMENT
22kΩ
3950 K
Murata, NCP18XW223E
±3%
22kΩ
3800 K
Vishay, NTCS0805E3223FHT
±1%
22kΩ
4554 K
TDK, NTCG164LH223HT
±3%
To linearize the resistance-temperature characteristic of the NTC termistor, a parallel resistor R18 is added. T is
the temperature at which the NTC characteristic curve is linearized. Typically T is located in the middle of the set
temperature range at which the VOFFE voltage should be adjusted. For example, if the temperature compensation
should start at 0°C and stop at 25°C T = 12.5°C + 273.15 K/°C = 285.65 K.
B - 2T
R18 = RNTC (T) ´
B + 2T
(28)
The resulting overall resistance RNTC||R18 can be calculated as follows.
R18 ´ RNTC (T)
RNTC||R18 =
R18 + RNTC (T)
(29)
30 kW
250 kW
25 kW
200 kW
20 kW
150 kW
15 kW
100 kW
10 kW
50 kW
5 kW
0 kW
-20ºC
0ºC
20ºC
40ºC
60ºC
80ºC
0 kW
-20ºC
0ºC
20ºC
40ºC
60ºC
80ºC
Figure 29. Resistance-Temperature Characteristics NTC (22 kΩ) and Linearized NTC Network at 12.5°C
To achieve different slopes, different R18 values are required. To obtain the most linear slope, the calculated
value has to be used. To achieve steeper slopes, higher values for R18 are necessary, smaller values produce
shallower slopes. By adjusting the resistor R19, the start and end point of the compensation can be set. The
voltage VTS of the resistor network at TS is calculated by the following equation:
VTS = Vlogic ´
R19
R19
= 3.3 V ´
RNTC||R18 + R19
RNTC||R18 + R19
(30)
Finally, the resulting output voltage, VOFFE, during the compensation period can be calculated as follows:
VOFFE = 2VTS - (Vlogic - 2VTS ) ´
R21
R21
= 2VTS - (3.3V - 2VTS ) ´
R20
R20
(31)
Figure 30 shows examples for VOFFE_min = –22V and VOFFE_max = –11V with different slopes and starting points of
the temperature compensation. For further compensation characteristics, refer to the available TPS65166
support excel sheet.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
27
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
-10 V
-10 V
-11 V
-11 V
-12 V
6 kW
10 kW
-13 V
7 kW
-14 V
12 kW
-14 V
-15 V
15 kW
-15 V
-12 V
-13 V
-16 V
8 kW
9 kW
-16 V
20 kW
-17 V
25 kW
-17 V
-18 V
30 kW
-18 V
10 kW
11 kW
-19 V
-19 V
-20 V
-20 V
-21 V
R18 = open
-21 V
R18 = 51 kW
-22 V
-22 V
-23 V
-10ºC
0ºC
10ºC
20ºC
30ºC
40ºC
50ºC
-23 V
-10ºC
0ºC
10ºC
20ºC
30ºC
40ºC
50ºC
-10 V
-10 V
-11 V
-11 V
5.5 kW
-12 V
-14 V
2.7 kW
-16 V
5 kW
-17 V
2.8 kW
-15 V
4.5 kW
-16 V
2.9 kW
-14 V
4 kW
-15 V
3 kW
-13 V
3.5 kW
-13 V
3.1 kW
-12 V
2.5 kW
-17 V
5.2 kW
-18 V
-18 V
-19 V
-19 V
-20 V
-20 V
-21 V
-21 V
R18 = 20 kW
R18 = 10 kW
-22 V
-22 V
-23 V
-10ºC
0ºC
10ºC
20ºC
30ºC
40ºC
50ºC
-23 V
-10ºC
0ºC
10ºC
20ºC
30ºC
40ºC
50ºC
Figure 30. Temperature Compensation Examples for R18 = open, 51 kΩ, 20 kΩ, 10 kΩ
Buck-Boost Converter Design Procedure
The first step in the design procedure is to verify whether the maximum possible output current of the buck-boost
converter supports the specific application requirements. To simplify the calculation, the fastest approach is to
estimate converter efficiency by taking the efficiency numbers from the provided efficiency curves or to use a
worst case assumption for the expected efficiency, e.g., 80%. The calculation must be performed for the
minimum assumed input voltage where the peak switch current is the highest. The inductor and external
Schottky diode have to be able to handle this current.
- Vout
1. Converter Duty Cycle:
D=
Vin ´ h - Vout
V ´ Dö
æ
2. Maximum output current: Iout = ç Iswpeak - in
÷ ´ (1- D)
2fs×L ø
è
3. Peak switch current:
Iswpeak =
Iout
V - D
+ in
1- D
2fs ´ L
(32)
With,
Iswpeak = Converter peak switch current (minimum switch current limit = 1.1A)
fs = Converter switching frequency (typical 750 kHz)
L = Selected inductor value
η = Estimated converter efficiency (use the number from the efficiency curves or 0.8 as an assumption)
28
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Inductor Selection (Buck-Boost Converter)
The buck-boost converter is able to operate with 10µH to 47µH inductors, a 22µH inductor is typical. The main
parameter for inductor selection is the saturation current of the inductor which should be higher than the peak
switch current as calculated in the Design Procedure section with additional margin to cover for heavy load
transients. The alternative more conservative approach is to choose an inductor with saturation current at least
as high as the minimum switch current limit of 1.1A. Another important parameter is the inductor dc resistance.
Usually the lower the dc resistance the higher the efficiency. The type and core material of the inductor
influences the efficiency as well. The efficiency difference among inductors can vary up to 5%. Possible inductors
are listed in Table 10.
Table 10. Inductor Selection Buck-Boost Converter
INDUCTOR VALUE
COMPONENT SUPPLIER
SIZE (LxWxH mm)
Isat/DCR
22µH
Sumida CDRH3D23/HP
4.0 × 4.0 × 2.5
0.8A/306mΩ
22µH
Sumida CDRH4D22/HP
5.0 × 5.0 × 2.4
1.1A/214mΩ
22µH
Sumida CDH3D13D/SHP
3.2 × 3.2 × 1.5
0.6A/753mΩ
Rectifier Diode Selection (Buck-Boost Converter)
To achieve high efficiency, a Schottky diode should be used. The reverse voltage rating should be higher than
the maximum output voltage of the buck-boost converter. The average rectified forward current, Iavg, the Schottky
diode needs to be rated for, is equal to the output current, Iout.
Iavg = Iout
(33)
Usually a Schottky diode with a 500mA maximum average rectified forward current rating is sufficient for most
applications. The Schottky rectifier can be selected with lower forward current capability depending on the output
current Iout, but has to be able to dissipate the power. The dissipated power is the average rectified forward
current times the diode forward voltage. The efficiency rises with lower forward voltage.
PD = Iavg × Vforward
(34)
Table 11. Rectifier Diode Selection (Buck-Boost Converter)
Vr/Iavg
Vforward
RθJA
SIZE
COMPONENT SUPPLIER
40V/0.5A
0.43V at 0.5A
206°C/W
SOD-123
MBR0540, Vishay Semiconductor
40V/1A
0.42V at 0.5A
88°C/W
SMA
SS14, Fairchild Semiconductor
Output Capacitor Selection (Buck-Boost Converter)
For the best output voltage filtering, low ESR ceramic capacitors are recommended. One 22µF or two 10µF
output capacitors with sufficient voltage ratings in parallel are adequate for most applications. Additional
capacitors can be added to improve load transient regulation. See Table 12 for output capacitor selection.
Table 12. Output Capacitor Selection (Buck-Boost Converter)
CAPACITOR
COMPONENT SUPPLIER
22µF/25V
Murata, GRM32ER61E226KE15
10µF/25V
Murata, GRM31CR61E106KA12
10µF/50V
Taiyo Yuden, UMK325BJ106MM
Positive Charge Pump Regulator (VONE)
This output rail is required to power the scan driver and is generated with a charge pump doubler stage running
from Vs and using the switch node of the boost converter. The external PNP transistor regulates the output
voltage to the programmed voltage set by the feedback resistor divider. Power dissipation and average collector
current of the transistor must be taken into consideration when choosing a suitable transistor. Also the power
dissipation of the resistor R12 must be considered.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
29
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
Setting the Output Voltage and Selecting the Feed-Forward Capacitor (Positive Charge Pump)
To minimize noise a minimum current through the feedback divider of 500 µA is recommended. At startup the
device is in short circuit mode with reduced current (typ. 50 µA) until the feedback voltage FB4 exceeds 100 mV,
then the device switches to soft-start mode until the output voltage VONE is in regulation. Due to the high output
current and low required voltage drop, high current Schottky diodes with low forward voltage are recommended
for this regulator.
æ R14 ö
æ R14 ö
Vout = VFB4 ´ ç 1+
= 1.24 V ´ ç 1+
÷
÷
è R15 ø
è R15 ø
(35)
VFB4
1.24V
R15 =
=
» 2.4 kW
500 mA
500 mA
(36)
æ V
ö
æ V
ö
R14 = R15 ´ ç out - 1÷ = R15 ´ ç out - 1÷
V
1.24
V
è
ø
è FB4
ø
(37)
To minimize noise and leakage current sensitivity keep the lower feedback divider resistor R15 between 100Ω
and 4.7kΩ. See typical application section for charge pump circuit.
Across the upper feedback resistor R14, a bypass capacitor C17 is required. The capacitor is calculated as:
C17 =
1
2 ´ p ´ 12 kHz ´ R14
(38)
Short circuit
Comparator
100 mV
Short circuit
Mode
Current Limit
&
Softstart
Control
Logic
Base2
55 mA
8 mA
1.24 V
Error Amplifier
FB4
Figure 31. Positive Chargepump Block Diagram
PNP Transistor Selection (Positive Charge Pump)
The maximum possible VONE output voltage is calculated as:
VONE = 2 ´ Vs + VD1 - 2 ´ VD2 -
IONE
´ R - VQ
D
(39)
With:
Vs = boost converter output voltage
VD1 = Forward voltage of boost converter Schottky diode
VD2 = Forward voltage of charge pump diode for a current of IONE / D
IONE = VONE output current
D = Duty cycle of boost converter (D = 1 – Vin / Vs)
R = Series resistor (if applicable, e.g., 2Ω for typical application)
VQ = Transistor saturation voltage
As a general recommendation the VONE voltage level in use should be at least 0.5V lower than the calculated
maximum VONE voltage.
30
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
The power dissipation of the transistor should be calculated for the maximum applied boost output voltage VS. If
high voltage stress mode (HVS) is used the maximum VS voltage occurs during HVS mode.:
I
æ
ö
Power dissipation = ç 2 ´ Vs - VONE - 2 ´ VD2 - ONE ´ R ÷ ´ IONE
D
è
ø
(40)
As an example for Vs = 18V and IONE = 150mA, the power dissipation is approximately 1W.
Because of the 1µF collector capacitor C16 a wide range of transistors can be used. The most important
transistor parameters are Collector-Emitter voltage which must be at least 2 x VS , average current rating of 1.2 x
IONE and DC current gain hFE, which must be at least IONE / IBase2. IBase2 minimum value of 8mA should be used
for calculation. See Table 13 for possible transistor selection.
Table 13. Transistor Selection (Positive Charge Pump)
TRANSISTOR
PZT2907A
KTA1552T
KTA1718D
KTA1666
Resistor R12 Function and Power Dissipation (Positive Charge Pump)
R12 is used to limit the peak current flowing from collector capacitor C16 through R12, D3 and C15 into the
boost switching node. High peak currents disturb the boost converter switching which results in high VS and VONE
ripple. The power dissipation for the resistor R12 can be calculated by following formula:
Presistor = R12 ´ IONE2
(41)
Output Capacitor Selection (Positive Charge Pump)
For the best output voltage filtering, low ESR ceramic output capacitors are recommended. Two 4.7 µF ceramic
output capacitors with sufficient voltage rating are adequate for most applications. Additional capacitors can be
added to improve the load transient regulation. See Table 14 for capacitor selection.
Table 14. Output Capacitor Selection (Positive Charge Pump)
CAPACITOR
COMPONENT SUPPLIER
4.7µF/50V
Murata, GRM31CR71H475KA12
4.7µF/50V
Taiyo Yuden, UMK316BJ475KL-T
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
31
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
Negative Shunt Regulator (Vss)
Vss is a shunt regulator that regulates the non-addressed TFT pixels to the programmed voltage. The pulldown
resistor R11 connected to VOFFE is required to provide accurate no load current regulation. A minimum current of
50µA through the feedback divider provides good accuracy. Be aware of the negative value of Vss for the
calculations.
Vout = VFB3 + (VFB3 - Vlogic ) ´
Vlogic - 0.75 ´ Vlogic
R10 =
R9 =
80 mA
=
Vlogic ´ R9
R9
R9
= 0.75 ´ Vlogic = 2.475V - 0.825 ´
R10
4 ´ R10
R10
0.825 V
» 10 kW
80 mA
(42)
(43)
Vout - 0.75 ´ Vlogic
Vout - VFB3
V - 2.475 V
´ R10 =
´ R10 = out
´ R10
-0.25 ´ Vlogic
-0.825 V
VFB3 - Vlogic
(44)
Discharge Resistor at VSS Output
If a discharge resistor Rdis at the VSS output is used to discharge the VSS node faster, the pull down resistor R11
connected to VOFFE must be calculated by following formula to achieve the programmed output voltage at VSS. A
smaller resistor to the calculated one must be used. For example for VSS = -7.5V, VOFFE = -11V and Rdis = 12kΩ
the calculated R11 = 4.98kΩ and the resistor values 4.7kΩ, 4.3kΩ, and 4.0kΩ can be used.
R11 =
Rdis ´ (R9 + R10) ´ (VOFFE - VSS )
VSS ´ (Rdis + R9 + R10) - Vlogic ´ Rdis
(45)
Base1
VSNS
Error Amplifier
5mA
max.
¾ Vref
FB3
Figure 32. Negative Shunt Regulator Block Diagram
Output Capacitor Selection (Negative Shunt Regulator)
For the best output voltage filtering, low ESR ceramic output capacitors are recommended. One 1µF ceramic
output capacitor with a sufficient voltage rating is suitable for most applications. See Table 15 for output capacitor
selection.
Table 15. Output Capacitor Selection (Negative Shunt Regulator)
32
CAPACITOR
COMPONENT SUPPLIER
1µF/25V
Murata, GRM21BR71E105KA99
1µF/50V
Taiyo Yuden, UMK325BJ105KH
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Layout Considerations
PCB layout is an important step in power supply design.
• NC pins 5, 8, 22, and 29 should not be connected to GND, if so, the device is not P2P short protected any
more.
• The input capacitors should be placed as close as possible to the device. AVIN, VIN1, and VIN2 must be
shorted.
• The buffer capacitor C25 must be connected to VL+ and AGND/VL- by a single trace.
• The line device, diode, output cap of the buck boost should be kept as short as possible.
• For the boost converter the line C3 GND output capacitor GND and PGND1 should be kept short.
• For the buck converter the line switch pin SW3, 4 to diode should be kept short.
• All lower feedback resistors connected to GND should be placed close to the device.
• Switching lines should not be next to feedback lines to avoid coupling.
• Use short lines or make sure the lines do not affect other regulating parts for the charge pump switching
connection to SW1,2 because this trace carrys switching waveforms.
• The PowerPAD™ of the QFN package should be soldered to GND and as much as possible thermal vias
should be used to lower the thermal resistance and keep the device cool.
• A solid PCB ground plane structure is essential for good device performance.
• Place red marked components and lines first and as close as possible to the device. Keep red marked lines
short. Bold marked lines should be wide on the PCB, because these traces carry high currents.
• Green marked components can be placed further away.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
33
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
Figure 33. PCB Layout Guideline
34
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Typical Applications
Figure 34. Typical Application With Vs= 15V, HVS = 18V, Vlogic = 3.3V
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
35
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
Figure 35. Typical Application With Vs = 18V, HVS = 19V, Vlogic = 3.3V
36
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
TPS65166
www.ti.com.......................................................................................................................................................................................... SLVS976 – SEPTEMBER 2009
Figure 36. Typical Application With Vs = 18V, HVS = 19V, Vlogic = 2.5V
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
37
TPS65166
SLVS976 – SEPTEMBER 2009.......................................................................................................................................................................................... www.ti.com
Recommended charge pump circuits.
Maximum Output Current VONE = 28V - 3%
VIN
VS = 15V
VS ³ 16V
10.8V
200mA
200mA
12.0V
180mA
200mA
13.2V
125mA
200mA
Figure 37. Typical Application VONE High Output Current
Maximum Output Current VONE = 28V - 3%
VIN
VS = 15V
VS ³ 16V
10.8V
100mA
200mA
12.0V
75mA
200mA
13.2V
50mA
200mA
Figure 38. Typical Application VONE Low Output Current
38
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65166
PACKAGE OPTION ADDENDUM
www.ti.com
4-Jun-2012
PACKAGING INFORMATION
Orderable Device
TPS65166RHAR
Status
(1)
OBSOLETE
Package Type Package
Drawing
VQFN
RHA
Pins
Package Qty
Eco Plan
40
TBD
(2)
Lead/
Ball Finish
Call TI
MSL Peak Temp
(3)
Samples
(Requires Login)
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated