1N3611GP THRU 1N3614GP AND 1N3957GP GLASS PASSIVATED JUNCTION RECTIFIER Reverse Voltage - 200 to 1000 Volts FEATURES T E D * DO-204AL N 1.0 (25.4) MIN. E P A T Forward Current - 1.0 Ampere 0.107 (2.7) 0.080 (2.0) DIA. 0.205 (5.2) 0.160 (4.1) 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. NOTE: Lead diameter is 0.026 (0.66) 0.023 (0.58) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ Glass passivated cavity-free junction ♦ 1.0 Ampere operation at TA=75°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension MECHANICAL DATA for suffix "E" part numbers Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306 ® Case: JEDEC DO-204AL molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 3611GP 1N 3612GP 1N 3613GP 1N 3614GP 1N 3957GP UNITS * Maximum repetitive peak reverse voltage VRRM 200 400 600 800 1000 Volts * Maximum RMS voltage VRMS 140 280 420 560 700 Volts * Maximum DC blocking voltage VDC 200 400 600 800 1000 Amps * Maximum average forward rectified current 0.375" (9.5mm) lead length at TA=75°C I(AV) 1.0 Amps * Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30.0 Amps VF 1.0 Volts IR 1.0 300.0 Typical reverse recovery time (NOTE 1) trr 2.0 µs Typical junction capacitance (NOTE 2) CJ 8.0 pF RΘJA RΘJL 55.0 25.0 °C/W TJ, TSTG -65 to +175 °C Maximum instantaneous forward voltage at 1.0A * Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=150°C Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr =0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length, P.C.B. mounted * JEDEC registered values 4/98 µA RATINGS AND CHARACTERISTIC CURVES 1N3611GP THRU 1N3614GP AND 1N3957GP FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.0 30 60 HZ RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - MAXIMUM FORWARD CURRENT DERATING 0.8 0.6 0.4 0.2 25 20 15 10 5.0 0.375" (9.5mm) LEAD LENGTH 0 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 50 75 100 150 125 100 10 1 25 0 175 NUMBER OF CYCLES AT 60 HZ AMBIENT TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 20 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 10 TJ=100°C 1 0.1 TJ=25°C 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.6 0.8 1.0 1.4 1.2 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE (°C/W) FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 20 100 10 1 0.1 0.01 0.1 1 10 t, PULSE DURATION, sec 100