TOSHIBA TLYE260A

TLYE260A
TOSHIBA LED Lamp InGaAℓP Yellow Light Emission
TLYE260A
Panel Circuit Indicator
Unit in mm
·
3.0 mm diameter
·
InGaAℓP yellow LED
·
All plastic mold type.
·
Colorless clear lens
·
Low drive current, high intensity yellow light emission
·
All plastic molded lens, provides an excellent on−off contrast ratio.
·
Fast response time, capable of pulse operation.
·
High power luminous intensity
·
Wide radiation pattern.
·
Applications: Suitable for backlighting.
Recommended forward current: IF = 15~20 mA (DC)
Maximum Ratings (Ta = 25°C)
Characteristic
Symbol
Rating
Unit
Forward current (DC)
IF
50
mA
Reverse voltage
VR
4
V
Power dissipation
PD
125
mW
Operating temperature range
Topr
-30~85
°C
TOSHIBA
Storage temperature range
Tstg
-40~120
°C
Weight: 0.12 g
1
JEDEC
―
EIAJ
―
4−3L1
2002-09-25
TLYE260A
Electrical And Optical Characteristics (Ta = 25°C)
Characteristic
Symbol
Test Condition
Min
Typ.
Max
Unit
Forward voltage
VF
IF = 20mA
¾
2.1
2.5
V
Reverse current
IR
VR = 4V
¾
¾
50
µA
IV
IF = 20mA
15.3
40
¾
15.3
¾
73.6
Peak emission wavelength
λP
IF = 20mA
¾
590
¾
nm
Spectral line half width
∆λ
IF = 20mA
¾
13
¾
nm
Dominant wavelength
λd
IF = 20mA
¾
587
¾
nm
Luminous intensity
TLYE260A
TLYE260A (KL)
(Note)
mcd
(Note): Lamps are classified into the following ranks according to their luminous intensity.
Measurement tolerance for each limit is ±15%.
K: 18-36 mcd, L: 32-64mcd, M: 56-112mcd.
Precaution
·
Please be careful of the followings
Soldering temperature: 260°C max
Soldering time: 3s max
(Soldering portion of lead: Up to 2mm from the body of the device)
·
If the lead is formed, the lead should be formed up to 5mm from the body of the device without forming stress to
the resin. Soldering should be performed after lead forming.
·
This visible LED lamp also emits some IR light. If a photodetector is located near the LED lamp, please ensure
that it will not be affected by this IR light.
2
2002-09-25
TLYE260A
IF – VF
IV – IF
50
500
(mcd)
IV
10
5
3
1
1.7
1.8
1.9
2.0
2.1
Forward voltage
2.2
VF
2.3
Ta = 25 °C
300
100
Luminous intensity
Forward current IF
(mA)
Ta = 25 °C
30
50
30
10
5
3
2
2.4
1
5
10
30
Forward current
50
IF
100
300 500
(mA)
Relative Luminous Intensity
Wavelength
IV – Tc
1.0
3
IF = 20 mA
Ta = 25 °C
Relative luminous intensity
IV
1
0.5
0.3
0.1
−20
0
20
40
Case temperature Tc
60
0.8
0.6
0.4
0.2
0
540
80
560
580
600
Wavelength λ
(°C)
Radiation Pattern
620
640
660
(nm)
IF – Ta
80
Ta = 25 °C
20°
10°
0°
10°
Allowable forward current
IF (mA)
Relative luminous intensity
3
(V)
20°
30°
30°
40°
40°
50°
50°
60°
60°
70°
70°
80°
90°
1
0.8
0.6
0.4
0.2
60
40
20
0
0
0
20
40
60
80
100
Ambient temperature Ta (°C)
3
2002-09-25
TLYE260A
RESTRICTIONS ON PRODUCT USE
000707EAC
· TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc..
· The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.
· Gallium arsenide (GaAs) is a substance used in the products described in this document. GaAs dust and fumes
are toxic. Do not break, cut or pulverize the product, or use chemicals to dissolve them. When disposing of the
products, follow the appropriate regulations. Do not dispose of the products with other industrial waste or with
domestic garbage.
· The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.
· The information contained herein is subject to change without notice.
4
2002-09-25