GP10A THRU GP10Y GLASS PASSIVATED JUNCTION RECTIFIER FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ 1.0 Ampere operation at TA=75°C and 55°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension T N 1.0 (25.4) MIN. E P A T Forward Current - 1.0 Ampere DO-204AL E D * Reverse Voltage - 50 to 1600 Volts 0.107 (2.7) 0.080 (2.0) DIA. 0.205 (5.2) 0.160 (4.1) 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. NOTE: Lead diameter is 0.026 (0.66) 0.023 (0.58) for suffix "E" part numbers MECHANICAL DATA Dimensions in inches and (millimeters) *Glass-plastic encapsulation is covered by Case: JEDEC DO-204AL molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306 ® MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS A B D Maximum repetitive peak reverse voltage VRRM Maximum average forward rectified current 0.375" (9.5mm) lead length (SEE FIG. 1) I(AV) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30.0 VF 1.1 Maximum instantaneous forward voltage at 1.0A Maximum full load reverse current, full cycle average, 0.375" (9.5mm) lead lengths at TA=75°C G J K M N Q T V W Y UNITS 50 to 1600 Volts (SEE FIG. 5) Volts 1.0 Amp 25.0 1.2 Amps 1.3 Volts IR(AV) 30.0 µA IR 5.0 50.0 µA Typical reverse recovery time (NOTE 1) trr 2.0 µs Typical junction capacitance (NOTE 2) CJ Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C Typical thermal resistance (NOTE 3) Operating junction and storage temperature range RΘJA TJ, TSTG NOTES: (1) Reverse recovery test condition: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead lengths, P.C.B. mounted 4/98 8.0 7.0 5.0 55.0 -65 to +175 pF °C/W -65 to +150 °C RATINGS AND CHARACTERISTIC CURVES GP10A THRU GP10Y 30 FIG. 1 - FORWARD CURRENT DERATING CURVE 1.0 GP10A - GP10M 0.8 60 HZ RESISTIVE OR INDUCTIVE LOAD GP10N - GP10Y 0.6 0.4 0.2 0.375" (9.5mm) LEAD LENGTH 0 20 40 60 80 100 120 140 160 AMBIENT TEMPERATURE, °C 180 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 25 GP10A - GP10M 20 15 GP10N - GP10Y 10 5.0 1 10 100 NUMBER OF CYCLES AT 60 HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 10 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 GP10A to GP10J GP10K to GP10Q GP10T to GP10Y 0.01 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 TJ=125°C 1 TJ=75°C 0.1 TJ=25°C 0.01 0.001 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE, VOLTS PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 6 - TYPICAL JUNCTION CAPACITANCE FIG. 5 - MAXIMUM REPETITIVE PEAK REVERSE VOLTAGE, VRRM GP10A GP10B GP10D GP10G GP10J GP10K GP10M GP10N GP10Q GP10T GP10V GP10W GP10Y . . . . . . .50V . . . . . .100V . . . . . .200V . . . . . .400V . . . . . .600V . . . . . .800V . . . . .1000V . . . . .1100V . . . . .1200V . . . . .1300V . . . . .1400V . . . .1500V . . . . .1600V 20 JUNCTION CAPACITANCE pF INSTANTANEOUS FORWARD CURRENT, AMPERES 20 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 GP10A to GP10J GP10K to GP10Q GP10T to GP10Y 1.0 0.1 1 10 REVERSE VOLTAGE, VOLTS 100