SN74LS194A 4-Bit Bidirectional Universal Shift Register The SN74LS194A is a High Speed 4-Bit Bidirectional Universal Shift Register. As a high speed multifunctional sequential building block, it is useful in a wide variety of applications. It may be used in serial-serial, shift left, shift right, serial-parallel, parallel-serial, and parallel-parallel data register transfers. The LS194A is similar in operation to the LS195A Universal Shift Register, with added features of shift left without external connections and hold (do nothing) modes of operation. It utilizes the Schottky diode clamped process to achieve high speeds and is fully compatible with all ON Semiconductor TTL families. • • • • • http://onsemi.com LOW POWER SCHOTTKY Typical Shift Frequency of 36 MHz Asynchronous Master Reset Hold (Do Nothing) Mode Fully Synchronous Serial or Parallel Data Transfers Input Clamp Diodes Limit High Speed Termination Effects 16 1 GUARANTEED OPERATING RANGES Symbol VCC Parameter Supply Voltage Min Typ Max Unit 4.75 5.0 5.25 V 0 25 70 °C TA Operating Ambient Temperature Range IOH Output Current – High – 0.4 mA IOL Output Current – Low 8.0 mA PLASTIC N SUFFIX CASE 648 16 1 SOIC D SUFFIX CASE 751B ORDERING INFORMATION Semiconductor Components Industries, LLC, 1999 December, 1999 – Rev. 6 1 Device Package Shipping SN74LS194AN 16 Pin DIP 2000 Units/Box SN74LS194AD 16 Pin 2500/Tape & Reel Publication Order Number: SN74LS194A/D SN74LS194A CONNECTION DIAGRAM DIP (TOP VIEW) VCC Q0 Q1 Q2 Q3 CP S1 S0 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 MR DSR P0 P1 P2 P3 DSL GND LOADING (Note a) PIN NAMES S0, S1 P0 – P3 DSR DSL CP MR Q0 – Q3 Mode Control Inputs Parallel Data Inputs Serial (Shift Right) Data Input Serial (Shift Left) Data Input Clock (Active HIGH Going Edge) Input Master Reset (Active LOW) Input Parallel Outputs NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW. http://onsemi.com 2 HIGH LOW 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L. SN74LS194A LOGIC DIAGRAM P0 10 S1 P1 P2 4 3 P3 5 6 9 S0 2 7 DSR VCC = PIN 16 GND = PIN 8 = PIN NUMBERS CP S Q0 S Q1 S Q2 S DSL Q3 CP CP CP CP R CLEAR R CLEAR R CLEAR R CLEAR 11 1 MR 15 14 Q0 13 Q2 Q1 12 Q3 FUNCTIONAL DESCRIPTION The Logic Diagram and Truth Table indicate the functional characteristics of the LS194A 4-Bit Bidirectional Shift Register. The LS194A is similar in operation to the ON Semiconductor LS195A Universal Shift Register when used in serial or parallel data register transfers. Some of the common features of the two devices are described below: All data and mode control inputs are edge-triggered, responding only to the LOW to HIGH transition of the Clock (CP). The only timing restriction, therefore, is that the mode control and selected data inputs must be stable one set-up time prior to the positive transition of the clock pulse. The register is fully synchronous, with all operations taking place in less than 15 ns (typical) making the device especially useful for implementing very high speed CPUs, or the memory buffer registers. The four parallel data inputs (P0, P1, P2, P3) are D-type inputs. When both S0 and S1 are HIGH, the data appearing on P0, P1, P2, and P3 inputs is transferred to the Q0, Q1, Q2, and Q3 outputs respectively following the next LOW to HIGH transition of the clock. The asynchronous Master Reset (MR), when LOW, overrides all other input conditions and forces the Q outputs LOW. Special logic features of the LS194A design which increase the range of application are described below: Two mode control inputs (S0, S1) determine the synchronous operation of the device. As shown in the Mode Selection Table, data can be entered and shifted from left to right (shift right, Q0 Q1, etc.) or right to left (shift left, Q3 Q2, etc.), or parallel data can be entered loading all four bits of the register simultaneously. When both S0 and S1,are LOW, the existing data is retained in a “do nothing” mode without restricting the HIGH to LOW clock transition. D-type serial data inputs (DSR, DSL) are provided on both the first and last stages to allow multistage shift right or shift left data transfers without interfering with parallel load operation. ! http://onsemi.com 3 ! SN74LS194A MODE SELECT — TRUTH TABLE OPERATING MODE INPUTS OUTPUTS MR S1 S0 DSR DSL Pn Q0 Q1 Q2 Q3 Reset L X X X X X L L L L Hold H I I X X X q0 q1 q2 q3 Shift Left H H h h I I X X I h X X q1 q1 q2 q2 q3 q3 L H Shift Right H H I I h h I h X X X X L H q0 q0 q1 q1 q2 q2 Parallel Load H h h X X Pn P0 P1 P2 P3 L = LOW Voltage Level H = HIGH Voltage Level X = Don’t Care I = LOW voltage level one set-up time prior to the LOW to HIGH clock transition h = HIGH voltage level one set-up time prior to the LOW to HIGH clock transition pn (qn) = Lower case letters indicate the state of the referenced input (or output) one set-up time prior to the LOW to HIGH clock transition. DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol Parameter VIH Input HIGH Voltage VIL Input LOW Voltage VIK Input Clamp Diode Voltage VOH Output HIGH Voltage VOL O Output LOW Voltage IIH Input HIGH Current IIL Input LOW Current IOS Short Circuit Current (Note 1) ICC Power Supply Current Min Typ Max 2.0 0.8 – 0.65 2.7 – 1.5 3.5 Unit Test Conditions V Guaranteed Input HIGH Voltage for All Inputs V Guaranteed Input LOW Voltage for All Inputs V VCC = MIN, IIN = – 18 mA V VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table VCC = VCC MIN, VIN = VIL or VIH per Truth Table 0.25 0.4 V IOL = 4.0 mA 0.35 0.5 V IOL = 8.0 mA 20 µA VCC = MAX, VIN = 2.7 V 0.1 mA VCC = MAX, VIN = 7.0 V – 0.4 mA VCC = MAX, VIN = 0.4 V – 100 mA VCC = MAX 23 mA VCC = MAX – 20 Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. AC CHARACTERISTICS (TA = 25°C) Limits Symbol Parameter Min Typ 25 36 Max Unit fMAX Maximum Clock Frequency tPLH tPHL Propagation Delay, Clock to Output 14 17 22 26 ns tPHL Propagation Delay, MR to Output 19 30 ns MHz http://onsemi.com 4 Test Conditions VCC = 5.0 V CL = 15 pF F SN74LS194A AC SETUP REQUIREMENTS (TA = 25°C) Limits Symbol Parameter Min Typ Max Unit tW Clock or MR Pulse Width 20 ns ts Mode Control Setup Time 30 ns ts Data Setup Time 20 ns th Hold time, Any Input 0 ns trec Recovery Time 25 ns Test Conditions VCC = 5.0 V DEFINITIONS OF TERMS continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW to HIGH and still be recognized. RECOVERY TIME (trec) — is defined as the minimum time required between the end of the reset pulse and the clock transition from LOW to HIGH in order to recognize and transfer HIGH Data to the Q outputs. SETUP TIME(ts) —is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW to HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) — is defined as the minimum time following the clock transition from LOW to HIGH that the logic level must be maintained at the input in order to ensure AC WAVEFORMS The shaded areas indicate when the input is permitted to change for predictable output performance. S0 (––– IS SHIFT LEFT) 1/fmax 1.3 V S1 1.3 V CLOCK tW tPHL OUTPUT tPLH ts(L) th(L) = 0 ts(H) th(H) = 0 P0 P1 P2 P3 OTHER CONDITIONS: S1 = L, MR = H, S0 = H ts(L) Figure 1. Clock to Output Delays Clock Pulse Width and fmax MR 1.3 V DSR DSL 1.3 V 1.3 V th(L) = 0 CLOCK OUTPUT* ts(H) th(H) = 0 1.3 V 1.3 V OTHER CONDITIONS: MR = H OTHER CONDITIONS: *DSR SET-UP TIME AFFECTS Q0 ONLY OTHER CONDITIONS: DSL SET-UP TIME AFFECTS Q3 ONLY 1.3 V trec tW Figure 3. Setup (ts) and Hold (th) Time for Serial Data (DSR, DSL) and Parallel Data (P0, P1, P2, P3) 1.3 V CLOCK tPHL OUTPUT (STABLE TIME) 1.3 V 1.3 V S0 S1 ts th = 0 OTHER CONDITIONS: S0, S1 = H OTHER CONDITIONS: PO = P1 = P2 = P3 = H CLOCK Figure 2. Master Reset Pulse Width, Master Reset to Output Delay and Master Reset to Clock Recovery Time ts th = 0 1.3 V 1.3 V OTHER CONDITIONS: MR = H Figure 4. Setup (ts) and Hold (th) Time for S Input http://onsemi.com 5 SN74LS194A PACKAGE DIMENSIONS N SUFFIX PLASTIC PACKAGE CASE 648–08 ISSUE R NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. –A– 16 9 1 8 B F C L S –T– SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M http://onsemi.com 6 DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 SN74LS194A D SUFFIX PLASTIC SOIC PACKAGE CASE 751B–05 ISSUE J –A– 16 9 1 8 –B– P NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 8 PL 0.25 (0.010) M B S G R K F X 45 _ C –T– SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S http://onsemi.com 7 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 SN74LS194A ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION North America Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong 800–4422–3781 Email: ONlit–[email protected] N. American Technical Support: 800–282–9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor – European Support German Phone: (+1) 303–308–7140 (M–F 2:30pm to 5:00pm Munich Time) Email: ONlit–[email protected] French Phone: (+1) 303–308–7141 (M–F 2:30pm to 5:00pm Toulouse Time) Email: ONlit–[email protected] English Phone: (+1) 303–308–7142 (M–F 1:30pm to 5:00pm UK Time) Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549 Phone: 81–3–5487–8345 Email: [email protected] Fax Response Line: 303–675–2167 800–344–3810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 8 SN74LS194A/D