NUD3105D Integrated Relay, Inductive Load Driver This device is used to switch inductive loads such as relays, solenoids incandescent lamps, and small DC motors without the need of a free−wheeling diode. The device integrates all necessary items such as the MOSFET switch, ESD protection, and Zener clamps. It accepts logic level inputs thus allowing it to be driven by a large variety of devices including logic gates, inverters, and microcontrollers. Features • Provides a Robust Driver Interface Between D.C. Relay Coil and • • • • • • Sensitive Logic Circuits Optimized to Switch Relays from 3.0 V to 5.0 V Rail Capable of Driving Relay Coils Rated up to 2.5 W at 5.0 V Internal Zener Eliminates the Need of Free−Wheeling Diode Internal Zener Clamp Routes Induced Current to Ground for Quieter Systems Operation Low VDS(ON) Reduces System Current Drain Pb−Free Package is Available Typical Applications • Telecom: Line Cards, Modems, Answering Machines, FAX • Computers and Office: Photocopiers, Printers, Desktop Computers • Consumer: TVs and VCRs, Stereo Receivers, CD Players, Cassette Recorders Equipment, Garage Door Openers Automotive: 5.0 V Driven Relays, Motor Controls, Power Latches, Lamp Drivers Gate (2) 6 5 MARKING DIAGRAM 4 1 2 3 JW4 D G G SC−74 CASE 318F STYLE 7 JW4 D G = Specific Device Code = Date Code = Pb−Free Package (Note: Microdot may be in either location) Device NUD3105DMT1 NUD3105DMT1G Package Shipping† SC−74 3000/Tape & Reel SC−74 (Pb−Free) 3000/Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. INTERNAL CIRCUIT DIAGRAMS Drain (6) Relay, Inductive Load Driver Silicon SMALLBLOCK] 0.5 Ampere, 8.0 V Clamp ORDERING INFORMATION • Industrial: Small Appliances, Security Systems, Automated Test • http://onsemi.com Drain (3) 1.0 k Gate (5) 1.0 k 300 k 300 k Source (1) Source (4) CASE 318F © Semiconductor Components Industries, LLC, 2006 March, 2006 − Rev. 3 1 Publication Order Number: NUD3105D/D NUD3105D MAXIMUM RATINGS (TJ = 25°C unless otherwise specified) Symbol Value Unit VDSS Drain to Source Voltage − Continuous 6.0 Vdc VGS Gate to Source Voltage – Continuous 6.0 Vdc ID Drain Current – Continuous 500 mA Ez Single Pulse Drain−to−Source Avalanche Energy (TJinitial = 25°C) 50 mJ TJ Junction Temperature 150 °C TA Operating Ambient Temperature −40 to 85 °C Tstg Storage Temperature Range −65 to +150 °C PD Total Power Dissipation (Note 1) Derating Above 25°C 380 1.5 mW mW/°C Thermal Resistance Junction−to−Ambient 329 °C/W RqJA Rating Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. This device contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL_STD−883, Method 3015. Machine Model Method 200 V. TYPICAL ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted) Symbol Characteristic Min Typ Max Unit 6.0 8.0 9.0 V OFF CHARACTERISTICS VBRDSS Drain to Source Sustaining Voltage (Internally Clamped) (ID = 10 mA) BVGSO Ig = 1.0 mA − − 8.0 V IDSS Drain to Source Leakage Current (VDS = 5.5 V , VGS = 0 V, TJ = 25°C) (VDS = 5.5 V, VGS = 0 V, TJ = 85°C ) − − − − 15 15 mA IGSS Gate Body Leakage Current (VGS = 3.0 V, VDS = 0 V) (VGS = 5.0 V, VDS = 0 V) 5.0 − − − 35 65 mA 0.8 0.8 1.2 − 1.4 1.4 V ON CHARACTERISTICS VGS(th) Gate Threshold Voltage (VGS = VDS, ID = 1.0 mA) (VGS = VDS, ID = 1.0 mA, TJ = 85°C) RDS(on) Drain to Source On−Resistance (ID = 250 mA, VGS = 3.0 V) (ID = 500 mA, VGS = 3.0 V) (ID = 500 mA, VGS = 5.0 V) (ID = 500 mA, VGS = 3.0 V, TJ = 85°C) (ID = 500 mA, VGS = 5.0 V, TJ = 85°C) − − − − − − − − − − 1.2 1.3 0.9 1.3 0.9 W IDS(on) Output Continuous Current (VDS = 0.25 V, VGS = 3.0 V) (VDS = 0.25 V, VGS = 3.0 V, TJ = 85°C) 300 200 400 − − − mA 350 570 − mMhos gFS Forward Transconductance (VOUT = 5.0 V, IOUT = 0.25 A) http://onsemi.com 2 NUD3105D TYPICAL ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted) Symbol Characteristic Min Typ Max Unit DYNAMIC CHARACTERISTICS Ciss Input Capacitance (VDS = 5.0 V,VGS = 0 V, f = 10 kHz) − 25 − pF Coss Output Capacitance (VDS = 5.0 V, VGS = 0 V, f = 10 kHz) − 37 − pF Crss Transfer Capacitance (VDS = 5.0 V, VGS = 0 V, f = 10 kHz) − 8.0 − pF Min Typ Max Units SWITCHING CHARACTERISTICS Characteristic Symbol tPHL tPLH Propagation Delay Times: High to Low Propagation Delay; Figure 1 (5.0 V) Low to High Propagation Delay; Figure 1 (5.0 V) − − 25 80 − − nS tPHL tPLH High to Low Propagation Delay; Figure 1 (3.0 V) Low to High Propagation Delay; Figure 1 (3.0 V) − − 44 44 − − tf tr Transition Times: Fall Time; Figure 1 (5.0 V) Rise Time; Figure 1 (5.0 V) − − 23 32 − − nS tf tr Fall Time; Figure 1 (3.0 V) Rise Time; Figure 1 (3.0 V) − − 53 30 − − VCC Vin 50% tPLH Vout tPHL GND VZ VCC 90% 50% 10% GND tr tf Figure 1. Switching Waveforms http://onsemi.com 3 − NUD3105D TYPICAL CHARACTERISTICS 10 TJ = 25°C VGS = 5.0 V 1.0 ID, DRAIN CURRENT (A) ID, DRAIN CURRENT (A) 10 VGS = 3.0 V 0.1 VGS = 2.0 V 0.01 0.001 0.01 50°C 0.0001 −40°C VGS = 1.0 V 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.000001 0.8 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 VDS, DRAIN TO SOURCE VOLTAGE (V) VGS, GATE−TO−SOURCE VOLTAGE (V) Figure 2. Output Characteristics Figure 3. Transfer Function 5.0 50 RDS(ON), DRAIN−TO−SOURCE RESISTANCE (W) ID = 0.5 A VGS = 3.0 V 1000 ID = 0.25 A VGS = 3.0 V 800 600 400 ID = 0.5 A VGS = 5.0 V 200 0 −50 −25 0 25 50 75 100 125 45 −40°C ID = 250 mA 40 35 125°C 30 85°C 25 50°C 20 25°C 15 0.8 1.0 1.2 1.4 1.6 1.8 TEMPERATURE (°C) VGS, GATE−TO−SOURCE VOLTAGE (V) Figure 4. On Resistance Variation vs. Temperature Figure 5. RDS(ON) Variation with Gate−To−Source Voltage IZ = 10 mA VZ, ZENER CLAMP VOLTAGE (V) 8.18 8.16 8.14 8.12 8.10 8.08 8.06 8.04 8.02 8.00 −50 2.0 13.0 8.20 VZ, ZENER VOLTAGE (V) 85°C 0.001 0.00001 1200 RDS(ON), DRAIN−TO−SOURCE RESISTANCE (mW) 0.1 25°C 0.0001 0.00001 VDS = 0.8 V 1.0 −25 0 25 50 75 100 125 VGS = 0 V 12.0 −40°C 11.0 25°C 10.0 9.0 8.0 7.0 85°C 6.0 0.1 1.0 10 100 1000 TEMPERATURE (°C) IZ, ZENER CURRENT (mA) Figure 6. Zener Voltage vs. Temperature Figure 7. Zener Clamp Voltage vs. Zener Current http://onsemi.com 4 NUD3105D TYPICAL CHARACTERISTICS 1.2 40 35 125°C IGSS, GATE LEAKAGE (mA) RDS(ON), DRAIN−TO−SOURCE RESISTANCE (W) 1.1 1.0 0.9 85°C 0.8 50°C 0.7 25°C 0.6 −40°C 0.5 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 30 25 VGS = 5.0 V 20 15 VGS = 3.0 V 10 5 0 −50 0 −25 ID, DRAIN CURRENT (A) ID, DRAIN CURRENT (A) 50 75 100 125 TEMPERATURE (°C) Figure 8. On−Resistance vs. Drain Current and Temperature 1.0 25 VGS = 3.0 V, TC = 25°C Figure 9. Gate Leakage vs. Temperature ID−Continuous = 0.5 A RDS(on) LIMIT THERMAL LIMIT PACKAGE LIMIT DC PW = 0.1 s DC = 50% 0.1 PW = 10 ms DC = 20% PW = 7.0 ms DC = 5% Typical IZ vs. VZ V(BR)DSS min = 6.0 V 0.01 0.01 0.1 1.0 10 100 VDS, DRAIN−TO−SOURCE VOLTAGE (V) Figure 10. Safe Operating Area for NUD3105DLT1 r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) 1.0 D = 0.5 0.2 0.1 0.1 0.05 Pd(pk) 0.02 0.01 0.01 0.001 0.01 PW SINGLE PULSE 0.1 t1 t2 PERIOD DUTY CYCLE = t1/t2 1.0 10 100 1000 10,000 t1, PULSE WIDTH (ms) Figure 11. Transient Thermal Response for NUD3105DLT1 http://onsemi.com 5 100,000 1,000,000 NUD3105D Designing with this Data Sheet 4. Verify that the circuit driving the gate will meet the VGS(th) from the Electrical Characteristics table. 5. Using the max output current calculated in step 1, check Figure 7 to insure that the range of Zener clamp voltage over temperature will satisfy all system & EMI requirements. 6. Use IGSS and IDSS from the Electrical Characteristics table to insure that “OFF” state leakage over temperature and voltage extremes does not violate any system requirements. 7. Review circuit operation and insure none of the device max ratings are being exceeded. 1. Determine the maximum inductive load current (at max VCC, min coil resistance & usually minimum temperature) that the NUD3105D will have to drive and make sure it is less than the max rated current. 2. For pulsed operation, use the Transient Thermal Response of Figure 11 and the instructions with it to determine the maximum limit on transistor power dissipation for the desired duty cycle and temperature range. 3. Use Figures 10 and 11 with the SOA notes to insure that instantaneous operation does not push the device beyond the limits of the SOA plot. APPLICATIONS DIAGRAMS +3.0 ≤ VDD ≤ +3.75 Vdc +4.5 ≤ VCC ≤ +5.5 Vdc + + Vout (6) Vout (3) NUD3105DDMT1 Vin (5) Vin (2) GND (1) GND (4) Figure 12. A 200 mW, 5.0 V Dual Coil Latching Relay Application with 3.0 V Level Translating Interface http://onsemi.com 6 NUD3105D Max Continuous Current Calculation for TX2−5V Relay, R1 = 178 W Nominal @ RA = 25°C Assuming ±10% Make Tolerance, R1 = 178 W * 0.9 = 160 W Min @ TA = 25°C − TC for Annealed Copper Wire is 0.4%/°C AROMAT JS1E−5V R1 = 160 W * [1+(0.004) * (−40°−25°)] = 118 W Min @ −40°C IO Max = (5.5 V Max − 0.25V) /118 W = 45 mA +4.5 TO +5.5 Vdc − AROMAT JS1E−5V + + + + +4.5 TO +5.5 Vdc + AROMAT JS1E−5V AROMAT TX2−5V AROMAT JS1E−5V − − − Vout (3) Vout (3) NUD3105DLT1 NUD3105DLT1 Vin (1) Vin (1) GND (2) GND (2) Figure 13. A 140 mW, 5.0 V Relay with TTL Interface Figure 14. A Quad 5.0 V, 360 mW Coil Relay Bank http://onsemi.com 7 NUD3105D PACKAGE DIMENSIONS SC−74 CASE 318F−05 ISSUE L NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. 318F−01, −02, −03 OBSOLETE. NEW STANDARD 318F−04. D 6 HE 1 5 4 2 3 E DIM A A1 b c D E e L HE q b e 0.05 (0.002) q C A L A1 MIN 0.90 0.01 0.25 0.10 2.90 1.30 0.85 0.20 2.50 0° MILLIMETERS NOM MAX 1.00 1.10 0.06 0.10 0.37 0.50 0.18 0.26 3.00 3.10 1.50 1.70 0.95 1.05 0.40 0.60 2.75 3.00 10° − MIN 0.035 0.001 0.010 0.004 0.114 0.051 0.034 0.008 0.099 0° INCHES NOM 0.039 0.002 0.015 0.007 0.118 0.059 0.037 0.016 0.108 − MAX 0.043 0.004 0.020 0.010 0.122 0.067 0.041 0.024 0.118 10° STYLE 7: PIN 1. SOURCE 1 2. GATE 1 3. DRAIN 2 4. SOURCE 2 5. GATE 2 6. DRAIN 1 SOLDERING FOOTPRINT* 2.4 0.094 0.95 0.037 1.9 0.074 0.95 0.037 0.7 0.028 1.0 0.039 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SMALLBLOCK is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 8 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. NUD3105D/D