SEMICONDUCTOR TECHNICAL DATA " #! "!$ "!$ High–Performance Silicon–Gate CMOS The MC54/74HC4016 utilizes silicon–gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF–channel leakage current. This bilateral switch/multiplexer/demultiplexer controls analog and digital voltages that may vary across the full power–supply range (from VCC to GND). The HC4016 is identical in pinout to the metal–gate CMOS MC14016 and MC14066. Each device has four independent switches. The device has been designed so that the ON resistances (RON) are much more linear over input voltage than RON of metal–gate CMOS analog switches. This device is identical in both function and pinout to the HC4066. The ON/OFF Control inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. For analog switches with voltage–level translators, see the HC4316. For analog switches with lower RON characteristics, use the HC4066. • Fast Switching and Propagation Speeds • High ON/OFF Output Voltage Ratio • Low Crosstalk Between Switches • Diode Protection on All Inputs/Outputs • Wide Power–Supply Voltage Range (VCC – GND) = 2.0 to 12.0 Volts • Analog Input Voltage Range (VCC – GND) = 2.0 to 12.0 Volts • Improved Linearity and Lower ON Resistance over Input Voltage than the MC14016 or MC14066 • Low Noise • Chip Complexity: 32 FETs or 8 Equivalent Gates 14 1 A ON/OFF CONTROL XB B ON/OFF CONTROL XC C ON/OFF CONTROL XD D ON/OFF CONTROL 1 2 1 D SUFFIX SOIC PACKAGE CASE 751A–03 14 1 ORDERING INFORMATION MC54HCXXXXJ MC74HCXXXXN MC74HCXXXXD Ceramic Plastic SOIC PIN ASSIGNMENT YA XA 1 14 YA 2 13 YB 3 12 XB B ON/OFF CONTROL C ON/OFF CONTROL GND 4 11 VCC A ON/OFF CONTROL D ON/OFF CONTROL XD 5 10 YD 6 9 YC 7 8 XC 13 4 3 YB 8 FUNCTION TABLE ANALOG OUTPUTS/INPUTS 5 9 YC 6 11 10 YD 12 ANALOG INPUTS/OUTPUTS = XA, XB, XC, XD PIN 14 = VCC PIN 7 = GND 10/95 Motorola, Inc. 1995 N SUFFIX PLASTIC PACKAGE CASE 646–06 14 LOGIC DIAGRAM XA J SUFFIX CERAMIC PACKAGE CASE 632–08 1 REV 6 On/Off Control Input State of Analog Switch L H Off On ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ MC54/74HC4016 MAXIMUM RATINGS* Symbol Parameter Value Unit – 0.5 to + 14.0 V V VCC Positive DC Supply Voltage (Referenced to GND) VIS Analog Input Voltage (Referenced to GND) – 0.5 to VCC + 0.5 Vin Digital Input Voltage (Referenced to GND) – 1.5 to VCC + 1.5 V DC Current Into or Out of Any Pin ± 25 mA PD Power Dissipation in Still Air, Plastic or Ceramic DIP† SOIC Package† 750 500 mW Tstg Storage Temperature – 65 to + 150 _C I TL This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high–impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND (Vin or Vout) VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. I/O pins must be connected to a properly terminated line or bus. v _C Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) (Ceramic DIP) 260 300 v * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. †Derating — Plastic DIP: – 10 mW/_C from 65_ to 125_C Ceramic DIP: – 10 mW/_C from 100_ to 125_C SOIC Package: – 7 mW/_C from 65_ to 125_C For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ v ÎÎÎÎ v ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 2.0 12.0 V VCC Positive DC Supply Voltage (Referenced to GND) VIS Analog Input Voltage (Referenced to GND) GND VCC V Vin Digital Input Voltage (Referenced to GND) GND VCC V — 1.2 V – 55 + 125 _C 0 0 0 0 1000 500 400 250 ns VIO* Static or Dynamic Voltage Across Switch TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time, ON/OFF Control Inputs (Figure 10) VCC = 2.0 V VCC = 4.5 V VCC = 9.0 V VCC = 12.0 V * For voltage drops across the switch greater than 1.2 V (switch on), excessive VCC current may be drawn; i.e., the current out of the switch may contain both VCC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded. DC ELECTRICAL CHARACTERISTICS Digital Section (Voltages Referenced to GND) Guaranteed Limit Symbol Parameter Test Conditions VCC V – 55 to 25_C 85_C 125_C Unit VIH Minimum High–Level Voltage ON/OFF Control Inputs Ron = per spec 2.0 4.5 9.0 12.0 1.5 3.15 6.3 8.4 1.5 3.15 6.3 8.4 1.5 3.15 6.3 8.4 V VIL Maximum Low–Level Voltage ON/OFF Control Inputs Ron = per spec 2.0 4.5 9.0 12.0 0.3 0.9 1.8 2.4 0.3 0.9 1.8 2.4 0.3 0.9 1.8 2.4 V Iin Maximum Input Leakage Current, ON/OFF Control Inputs Vin = VCC or GND 12.0 ±0.1 ±1.0 ±1.0 µA Maximum Quiescent Supply Current (per Package) Vin = VCC or GND VIO = 0 V 6.0 12.0 2 8 20 80 40 160 µA ICC NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). MOTOROLA 2 High–Speed CMOS Logic Data DL129 — Rev 6 ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ v ÎÎÎÎ v ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ v ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ v ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ v ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎ v ÎÎÎÎ v ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ MC54/74HC4016 DC ELECTRICAL CHARACTERISTICS Analog Section (Voltages Referenced to GND) Guaranteed Limit Symbol Ron VCC V – 55 to 25_C 85_C 125_C Vin = VIH VIS = VCC to GND IS 2.0 mA (Figures 1, 2) 2.0† 4.5 9.0 12.0 — 320 170 170 — 400 215 215 — 480 255 255 Vin = VIH VIS = VCC or GND (Endpoints) IS 2.0 mA (Figures 1, 2) 2.0 4.5 9.0 12.0 — 180 135 135 — 225 170 170 — 270 205 205 Parameter Test Conditions Maximum “ON” Resistance Unit Ω ∆Ron Maximum Difference in “ON” Resistance Between Any Two Channels in the Same Package Vin VIH VIS = 1/2 (VCC – GND) IS 2.0 mA 2.0 4.5 9.0 12.0 — 30 20 20 — 35 25 25 — 40 30 30 Ω Ioff Maximum Off–Channel Leakage Current, Any One Channel Vin = VIL VIO = VCC or GND Switch Off (Figure 3) 12.0 0.1 0.5 1.0 µA Ion Maximum On–Channel Leakage Current, Any One Channel Vin = VIH VIS = VCC or GND (Figure 4) 12.0 0.1 0.5 1.0 µA †At supply voltage (V CC – GND) approaching 2 V the analog switch–on resistance becomes extremely non–linear. Therefore, for low–voltage operation, it is recommended that these devices only be used to control digital signals. NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, ON/OFF Control Inputs: tr = tf = 6 ns) Guaranteed Limit Symbol Parameter VCC V – 55 to 25_C 85_C 125_C Unit tPLH, tPHL Maximum Propagation Delay, Analog Input to Analog Output (Figures 8 and 9) 2.0 4.5 9.0 12.0 50 10 10 10 65 13 13 13 75 15 15 15 ns tPLZ, tPHZ Maximum Propagation Delay, ON/OFF Control to Analog Output (Figures 10 and 11) 2.0 4.5 9.0 12.0 150 30 30 30 190 38 38 38 225 45 45 45 ns tPZL, tPZH Maximum Propagation Delay, ON/OFF Control to Analog Output (Figures 10 and 11) 2.0 4.5 9.0 12.0 125 25 25 25 160 32 32 32 185 37 37 37 ns ON/OFF Control Input — 10 10 10 pF Control Input = GND Analog I/O Feedthrough — — 35 1.0 35 1.0 35 1.0 C Maximum Capacitance NOTES: 1. For propagation delays with loads other than 50 pF, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). 2. Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). Typical @ 25°C, VCC = 5.0 V CPD Power Dissipation Capacitance (Per Switch)* (Figure 13) 15 pF * Used to determine the no–load dynamic power consumption: PD = CPD VCC 2 f + ICC VCC . For load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). High–Speed CMOS Logic Data DL129 — Rev 6 3 MOTOROLA ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ v ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ MC54/74HC4016 ADDITIONAL APPLICATION CHARACTERISTICS (Voltages Referenced to GND unless noted) VCC V Limit* 25_C 54/74HC Symbol Parameter Test Conditions BW Maximum On–Channel Bandwidth or Minimum Frequency Response (Figure 5) fin = 1 MHz Sine Wave Adjust fin Voltage to Obtain 0 dBm at VOS Increase fin Frequency Until dB Meter Reads – 3 dB RL = 50 Ω, CL = 10 pF 4.5 9.0 12.0 150 160 160 MHz Off–Channel Feedthrough Isolation (Figure 6) fin Sine Wave Adjust fin Voltage to Obtain 0 dBm at VIS fin = 10 kHz, RL = 600 Ω, CL = 50 pF 4.5 9.0 12.0 – 50 – 50 – 50 dB fin = 1.0 MHz, RL = 50 Ω, CL = 10 pF 4.5 9.0 12.0 – 40 – 40 – 40 Vin 1 MHz Square Wave (tr = tf = 6 ns) Adjust RL at Setup so that IS = 0 A RL = 600 Ω, CL = 50 pF 4.5 9.0 12.0 60 130 200 RL = 10 kΩ, CL = 10 pF 4.5 9.0 12.0 30 65 100 fin Sine Wave Adjust fin Voltage to Obtain 0 dBm at VIS fin = 10 kHz, RL = 600 Ω, CL = 50 pF 4.5 9.0 12.0 – 70 – 70 – 70 fin = 1.0 MHz, RL = 50 Ω, CL = 10 pF 4.5 9.0 12.0 – 80 – 80 – 80 — — — THD Feedthrough Noise, Control to Switch (Figure 7) Crosstalk Between Any Two Switches (Figure 12) Total Harmonic Distortion (Figure 14) fin = 1 kHz, RL = 10 kΩ, CL = 50 pF THD = THDMeasured – THDSource VIS = 4.0 VPP sine wave VIS = 8.0 VPP sine wave VIS = 11.0 VPP sine wave Unit mVPP dB % 4.5 9.0 12.0 0.10 0.06 0.04 * Guaranteed limits not tested. Determined by design and verified by qualification. MOTOROLA 4 High–Speed CMOS Logic Data DL129 — Rev 6 MC54/74HC4016 300 3000 2500 R on , ON RESISTANCE (OHMS) R on , ON RESISTANCE (OHMS) 125°C 2000 1500 25°C 1000 – 55°C 500 0 0 250 200 125°C 150 25°C 100 – 55°C 50 0 .25 .50 .75 1.00 1.25 1.5 1.75 2.00 Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND 0 Figure 1a. Typical On Resistance, VCC = 2.0 V 120 140 120 R on , ON RESISTANCE (OHMS) 125°C 25°C 100 80 – 55°C 60 40 20 0 0 .5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 100 80 125°C 60 25°C 40 20 0 0 6.0 – 55°C 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND Figure 1c. Typical On Resistance, VCC = 6.0 V Figure 1d. Typical On Resistance, VCC = 9.0 V 80 PLOTTER 70 R on , ON RESISTANCE (OHMS) 4.5 Figure 1b. Typical On Resistance, VCC = 4.5 V 160 R on , ON RESISTANCE (OHMS) .5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND 125°C 60 PROGRAMMABLE POWER SUPPLY 25°C 50 40 – + DC ANALYZER VCC – 55°C 30 MINI COMPUTER DEVICE UNDER TEST 20 ANALOG IN 10 0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 GND Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND Figure 1e. Typical On Resistance, VCC = 12.0 V High–Speed CMOS Logic Data DL129 — Rev 6 COMMON OUT Figure 2. On Resistance Test Set–Up 5 MOTOROLA MC54/74HC4016 VCC VCC VCC VCC 14 GND 14 A A VCC OFF 7 SELECTED CONTROL INPUT VIL 7 Figure 3. Maximum Off Channel Leakage Current, Any One Channel, Test Set–Up VIS ON 0.1µF CL* 7 SELECTED CONTROL INPUT SELECTED CONTROL INPUT VIH Figure 4. Maximum On Channel Leakage Current, Channel to Channel, Test Set–Up VOS VCC 14 fin N/C ON GND VCC 14 fin dB METER VOS OFF 0.1µF CL* RL dB METER SELECTED CONTROL INPUT VCC 7 *Includes all probe and jig capacitance. *Includes all probe and jig capacitance. Figure 5. Maximum On–Channel Bandwidth Test Set–Up VCC VCC/2 Figure 6. Off–Channel Feedthrough Isolation, Test Set–Up VCC/2 14 RL RL OFF/ON VOS IS VCC CL* VCC GND Vin ≤ 1 MHz tr = tf = 6 ns 7 ANALOG IN SELECTED CONTROL INPUT 50% GND tPHL tPLH CONTROL 50% ANALOG OUT *Includes all probe and jig capacitance. Figure 7. Feedthrough Noise, ON/OFF Control to Analog Out, Test Set–Up MOTOROLA Figure 8. Propagation Delays, Analog In to Analog Out 6 High–Speed CMOS Logic Data DL129 — Rev 6 MC54/74HC4016 VCC tr tf 14 ANALOG IN ANALOG OUT ON TEST POINT VCC 90% 50% 10% CONTROL GND CL* 7 SELECTED CONTROL INPUT tPZL tPLZ HIGH IMPEDANCE 50% VCC ANALOG OUT tPZH 10% VOL 90% VOH tPHZ 50% HIGH IMPEDANCE *Includes all probe and jig capacitance. Figure 9. Propagation Delay Test Set–Up Figure 10. Propagation Delay, ON/OFF Control to Analog Out POSITION 1 WHEN TESTING tPHZ AND tPZH VIS POSITION 2 WHEN TESTING tPLZ AND tPZL 1 2 VCC RL VCC VCC fin 1 kΩ 14 1 VOS ON 0.1 µF TEST POINT ON/OFF 2 14 OFF VCC OR GND CL* RL RL SELECTED CONTROL INPUT SELECTED CONTROL INPUT CL* VCC/2 RL CL* VCC/2 7 7 VCC/2 *Includes all probe and jig capacitance. *Includes all probe and jig capacitance Figure 11. Propagation Delay Test Set–Up Figure 12. Crosstalk Between Any Two Switches, Test Set–Up VCC A VIS VCC 14 NC OFF/ON VOS 0.1 µF NC fin ON RL 7 CL* TO DISTORTION METER VCC/2 SELECTED CONTROL INPUT 7 SELECTED CONTROL INPUT VCC ON/OFF CONTROL *Includes all probe and jig capacitance. Figure 13. Power Dissipation Capacitance Test Set–Up High–Speed CMOS Logic Data DL129 — Rev 6 Figure 14. Total Harmonic Distortion, Test Set–Up 7 MOTOROLA MC54/74HC4016 0 – 10 FUNDAMENTAL FREQUENCY – 20 dBm – 30 – 40 – 50 DEVICE – 60 SOURCE – 70 – 80 – 90 – 100 1.0 2.0 3.0 FREQUENCY (kHz) Figure 15. Plot, Harmonic Distortion below, the difference between VCC and GND is twelve volts. Therefore, using the configuration in Figure 16, a maximum analog signal of twelve volts peak–to–peak can be controlled. When voltage transients above VCC and/or below GND are anticipated on the analog channels, external diodes (Dx) are recommended as shown in Figure 17. These diodes should be small signal, fast turn–on types able to absorb the maximum anticipated current surges during clipping. An alternate method would be to replace the Dx diodes with MO sorbs (Motorola high current surge protectors). MOsorbs are fast turn–on devices ideally suited for precise DC protection with no inherent wear–out mechanism. APPLICATION INFORMATION The ON/OFF Control pins should be at V CC or GND logic levels, VCC being recognized as logic high and GND being recognized as a logic low. Unused analog inputs/outputs may be left floating (not connected). However, it is advisable to tie unused analog inputs and outputs to VCC or GND through a low value resistor. This minimizes crosstalk and feedthrough noise that may be picked up by the unused I/O pins. The maximum analog voltage swings are determined by the supply voltages VCC and GND. The positive peak analog voltage should not exceed VCC. Similarly, the negative peak analog voltage should not go below GND. In the example VCC = 12 V + 12 V 14 ANALOG I/O ON + 12 V ANALOG O/I 0V 0V SELECTED CONTROL INPUT + 12 V OTHER CONTROL INPUTS (VCC OR GND) 7 Figure 16. 12 V Application VCC VCC Dx 14 Dx ON Dx VCC Dx SELECTED CONTROL INPUT 7 OTHER CONTROL INPUTS (VCC OR GND) Figure 17. Transient Suppressor Application MOTOROLA 8 High–Speed CMOS Logic Data DL129 — Rev 6 MC54/74HC4016 +5 V +5 V 14 ANALOG SIGNALS R* R* R* R* HC4016 LSTTL/ NMOS 14 HCT BUFFER LSTTL/ NMOS 5 6 ANALOG SIGNALS HC4016 5 6 CONTROL INPUTS 15 14 ANALOG SIGNALS ANALOG SIGNALS 14 CONTROL INPUTS 15 7 7 R* = 2 TO 10 kΩ a. Using Pull-Up Resistors b. Using HCT Buffer Figure 18. LSTTL/NMOS to HCMOS Interface VDD = 5 V 13 1 VCC = 5 TO 12 V 16 14 ANALOG SIGNALS 3 ANALOG SIGNALS HC4016 5 2 5 9 4 6 11 6 14 CONTROL INPUTS 10 15 7 7 MC14504 14 8 Figure 19. TTL/NMOS–to–CMOS Level Converter Analog Signal Peak–to–Peak Greater than 5 V (Also see HC4316) CHANNEL 4 1 OF 4 SWITCHES CHANNEL 3 1 OF 4 SWITCHES CHANNEL 2 1 OF 4 SWITCHES CHANNEL 1 1 OF 4 SWITCHES COMMON I/O – INPUT 1 OF 4 SWITCHES + OUTPUT LF356 OR EQUIVALENT 0.01 µF 1 2 3 4 CONTROL INPUTS Figure 20. 4–Input Multiplexer High–Speed CMOS Logic Data DL129 — Rev 6 Figure 21. Sample/Hold Amplifier 9 MOTOROLA MC54/74HC4016 OUTLINE DIMENSIONS J SUFFIX CERAMIC DIP PACKAGE CASE 632–08 ISSUE Y -A14 8 1 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMESNION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. -B- C -T- L DIM A B C D F G J K L M N K SEATING PLANE F G D 14 PL 0.25 (0.010) M N T A M J 14 PL 0.25 (0.010) S M T B S N SUFFIX PLASTIC DIP PACKAGE CASE 646–06 ISSUE L 14 B 7 A F DIM A B C D F G H J K L M N L C J N H G D SEATING PLANE K M D SUFFIX PLASTIC SOIC PACKAGE CASE 751A–03 ISSUE F –A– 14 1 P 7 PL 0.25 (0.010) 7 G D 0.25 (0.010) MOTOROLA M T B S M F M K 14 PL B R X 45° C SEATING PLANE M A S 10 INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0_ 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0_ 10_ 0.39 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 8 –B– MILLIMETERS MIN MAX 19.05 19.94 6.23 7.11 3.94 5.08 0.39 0.50 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0° 15° 0.51 1.01 NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. 8 1 INCHES MIN MAX 0.750 0.785 0.245 0.280 0.155 0.200 0.015 0.020 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0° 15° 0.020 0.040 J DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.75 8.55 4.00 3.80 1.75 1.35 0.49 0.35 1.25 0.40 1.27 BSC 0.25 0.19 0.25 0.10 7° 0° 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 7° 0° 0.228 0.244 0.010 0.019 High–Speed CMOS Logic Data DL129 — Rev 6 MC54/74HC4016 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] –TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 High–Speed CMOS Logic Data DL129 — Rev 6 ◊ CODELINE *MC54/74HC4016/D* 11 MC54/74HC4016/D MOTOROLA