NCS2002, NCV2002 Sub−One Volt Rail−to−Rail Operational Amplifier with Enable Feature The NCS2002 is an industry first sub−one volt operational amplifier that features a rail−to−rail common mode input voltage range, along with rail−to−rail output drive capability. This amplifier is guaranteed to be fully operational down to 0.9 V, providing an ideal solution for powering applications from a single cell Nickel Cadmium (NiCd) or Nickel Metal Hydride (NiMH) battery. Additional features include no output phase reversal with overdriven inputs, trimmed input offset voltage of 0.5 mV, extremely low input bias current of 40 pA, and a unity gain bandwidth of 1.1 MHz at 5.0 V. The NCS2002 also has an active high enable pin that allows external shutdown of the device. In the standby mode, the supply current is typically 1.9 A at 1.0 V. Because of its small size and enable feature, this amplifier represents the ideal solution for small portable electronic applications. The NCS2002 is available in the space saving SOT23−6 (TSOP−6) package with two industry standard pinouts. http://onsemi.com MARKING DIAGRAM 65 4 3 12 x = P for NCS2002SN1T1 Q for NCS2002SN2T1 AA = Assembly Location Y = Year W = Work Week PIN CONNECTIONS 0.9 V Guaranteed Operation Standby Mode: ID = 1.9 A at 1.0 V, Typical Rail−to−Rail Common Mode Input Voltage Range Rail−to−Rail Output Drive Capability No Output Phase Reversal for Over−Driven Input Signals 0.5 mV Trimmed Input Offset 10 pA Input Bias Current 1.1 MHz Unity Gain Bandwidth at 2.5 V, 1.0 MHz at 0.5 V Tiny SOT23−6 (TSOP−6) Package VOUT 1 VCC Non−Inverting Input 2 VEE 5 Enable 4 Inverting Input + − 3 VOUT VEE Non−Inverting Input 1 6 VCC 2 5 Enable 4 Inverting Input + − 3 Style 2 Pinout (SN2T1) Single Cell NiCd / NiMH Battery Powered Applications Cellular Telephones Pagers Personal Digital Assistants Electronic Games Digital Cameras Camcorders Hand Held Instruments Rail to Rail Input 0.8 V to 7.0 V 6 Style 1 Pinout (SN1T1) Typical Applications • • • • • • • • AAxYW 1 Features • • • • • • • • • 6 TSOP SN SUFFIX CASE 318G ORDERING INFORMATION Rail to Rail Output Device Package Shipping† NCS2002SN1T1 TSOP 3000/Tape & Reel NCS2002SN2T1 TSOP 3000/Tape & Reel NCV2002SN1T1* TSOP 3000/Tape & Reel NCV2002SN2T1* TSOP 3000/Tape & Reel *NCV2002: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. + − †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. This device contains 81 active transistors. Figure 1. Typical Application Semiconductor Components Industries, LLC, 2004 January, 2004 − Rev. 2 1 Publication Order Number: NCS2002/D NCS2002, NCV2002 MAXIMUM RATINGS Rating Symbol Value Unit VS 7.0 V Input Differential Voltage Range (Note 1) VIDR VEE – 300 mV to 7.0 V V Input Common Mode Voltage Range (Note 1) VICR VEE – 300 mV to 7.0 V V Output Short Circuit Duration (Note 2) tSc Indefinite sec Junction Temperature TJ 150 °C RJA PD 235 340 °C/W mW Supply Voltage (VCC to VEE) Power Dissipation and Thermal Characteristics SOT23−6 Package Thermal Resistance, Junction to Air Power Dissipation @ TA = 70°C °C Operating Ambient Temperature Range NCS2002 NCV2002 (Note 3) TA Storage Temperature Range Tstg −65 to 150 °C VESD 2000 V ESD Protection at any Pin Human Body Model (Note 4) −40 to 105 −40 to 125 1. Either or both inputs should not exceed the range of VEE – 300 mV to VEE + 7.0 V. 2. Maximum package power dissipation limits must be observed to ensure that the maximum junction temperature is not exceeded. TJTA + (PD RJA) 3. NCV prefix is for automotive and other applications requiring site and change control. 4. ESD data available upon request. DC ELECTRICAL CHARACTERISTICS (VCC = 2.5 V, VEE = −2.5 V, VCM = VO = 0 V, RL to Gnd, TA = 25°C, unless otherwise noted) Rating Symbol Input Offset Voltage VCC = 0.45 V, VEE = −0.45 V TA = 25°C TA = 0°C to 70°C TA = Tlow to Thigh VCC = 1.5 V, VEE = −1.5 V TA = 25°C TA = 0°C to 70°C TA = Tlow to Thigh VCC = 2.5 V, VEE = −2.5 V TA = 25°C TA = 0°C to 70°C TA = Tlow to Thigh Min Typ Max VIO Unit mV −6.0 −8.5 −9.5 0.5 − − 6.0 8.5 9.5 −6.0 −7.0 −7.5 0.5 − − 6.0 7.0 7.5 −6.0 −7.5 −7.5 0.5 − − 6.0 7.5 7.5 VIO / T − 8.0 − V/°C IIB − 10 − pA Input Common Mode Voltage Range VICR − VEE to VCC − V Large Signal Voltage Gain VCC = 0.45 V, VEE = −0.45 V RL = 10 k VCC = 1.5 V, VEE = −1.5 V RL = 10 k VCC = 2.5 V, VEE = −2.5 V RL = 10 k AVOL Output Voltage Swing, High State Output (VID = + 0.5 V) TA = Tlow to Thigh VCC = 0.45 V, VEE = −0.45 V RL = 10 k RL = 2.0 k VCC = 1.5 V, VEE = −1.5 V RL = 10 k RL = 2.0 k VCC = 2.5 V, VEE = −2.5 V RL = 10 k RL = 2.0 k VOH Input Offset Voltage Temperature Coefficient (RS = 50) TA = Tlow to Thigh Input Bias Current (VCC = 1.0 V to 5.0 V) http://onsemi.com 2 kV/V − 40 − − 40 − 10 40 − V 0.40 0.35 0.442 0.409 − − 1.45 1.40 1.494 1.473 − − 2.45 2.40 2.493 2.469 − − NCS2002, NCV2002 DC ELECTRICAL CHARACTERISTICS (VCC = 2.5 V, VEE = −2.5 V, VCM = VO = 0 V, RL to Gnd, TA = 25°C, unless otherwise noted) Rating Symbol Output Voltage Swing, Low State Output (VID = − 0.5 V) TA = Tlow to Thigh VCC = 0.45 V, VEE = −0.45 V RL = 10 k RL = 2.0 k VCC = 1.5 V, VEE = −1.5 V RL = 10 k RL = 2.0 k VCC = 2.5 V, VEE = −2.5 V RL = 10 k RL = 2.0 k Min Typ Max VOL Unit V − − −0.446 −0.432 −0.40 −0.35 − − −1.497 −1.484 −1.45 −1.40 − − −2.496 −2.481 −2.45 −2.40 Common Mode Rejection Ratio (Vin = 0 to 5.0 V) TA = Tlow to Thigh CMRR 60 82 − dB Power Supply Rejection Ratio (VCC = 0.5 V to 2.5 V, VEE = −2.5 V) TA = Tlow to Thigh PSRR 60 85 − dB Output Short Circuit Current VCC = 0.45 V, VEE = −0.45 V, VID = 0.4 V Source Current High Output State Sink Current Low Output State VCC = 1.5 V, VEE = −1.5 V, VID = 0.5 V Source Current High Output State Sink Current Low Output State VCC = 2.5 V, VEE = −2.5 V, VID = 0.5 V Source Current High Output State Sink Current Low Output State ISC Power Supply Current (Per Amplifier, VO = 0 V) TA = Tlow to Thigh VCC = 0.5 V to VEE = −0.5 V Venable = VCC Venable = VEE VCC = 1.5 V to VEE = −1.5 V Venable = VCC Venable = VEE VCC = 2.5 V to VEE = −2.5 V Venable = VCC Venable = VEE ID Enable Input Threshold Voltage (VCC = 2.5 V, VEE = −2.5 V) Operating Disabled Vth(EN) Enable Input Current (VCC = 5.0 V, VEE = 0) Enable = 5.0 V Enable = Gnd IEnable http://onsemi.com 3 mA 0.5 − 1.0 −3.0 − −2.0 25 − 32 −58 − −45 65 − 86 −128 − −100 − − 480 1.5 600 3.0 − − 720 2.2 900 5.0 − − 820 2.5 1000 5.0 − 1.7 V + VEE 2.7 V + VEE 1.9 2.8 V + VEE − − − 1.1 1.1 2.0 2.0 V A NCS2002, NCV2002 AC ELECTRICAL CHARACTERISTICS(VCC = 2.5 V, VEE = −2.5 V, VCM = VO = 0 V, RL to Gnd, TA = 25°C, unless otherwise noted) Rating Symbol Min Typ Max Unit Differential Input Resistance (VCM = 0 V) Rin − >1.0 − tera Differential Input Capacitance (VCM = 0 V) Cin − 3.0 − pf Equivalent Input Noise Voltage (f = 1.0 kHz) en − 100 − nV/Hz − − 0.6 0.8 0.8 0.9 − − − Gain Bandwidth Product (f = 100 kHz) VCC = 0.45 V, VEE = −0.45 V VCC = 1.5 V, VEE = −1.5 V VCC = 2.5 V, VEE = −2.5 V GBW MHz Gain Margin (RL = 10 k, CL = 5.0 pf) Am − 6.5 − dB Phase Margin (RL = 10 k, CL = 5.0 pf) m − 60 − Deg Power Bandwidth (VO = 4.0 Vpp, RL = 2.0 k, THD = 1.0 %, AV = 1.0) BWP − 80 − kHz Total Harmonic Distortion (VO = 4.0 Vpp, RL = 2.0 k, AV = 1.0) f = 1.0 kHz f = 10 kHz THD − − 0.008 0.08 − − 0.85 0.85 1.2 1.3 − − % Slew Rate (VS = 2.5 V, VO = −2.0 V to 2.0 V, RL = 2.0 k, AV = 1.0) Positive Slope Negative Slope SR Time Delay for Device to Turn On (RL = 10 k) ton − 5.5 7.5 s Time Delay for Device to Turn Off (RL = 10 k) toff − 2.5 3.0 s http://onsemi.com 4 V/s NCS2002, NCV2002 0 VCC VS = ±2.5 V RL to Gnd TA = 25°C −200 High State Output Sourcing Current −400 Vsat, Output Saturation Voltage (V) −600 600 400 Low State Output Sinking Current 200 VEE −0.1 −0.2 VCC VS = 2.5 V RL to Gnd TA = 25°C −0.3 −0.4 High State Output Sourcing Current −0.5 0.4 Low State Output Sinking Current 0.3 0.2 0.1 VEE 0 0 100 1.0 k 10 k 100 k 0 1.0 M 8.0 4.0 RL, Load Resistance () Figure 2. Output Saturation Voltage versus Load Resistance 1000 80 100 10 VS = ±2.5 V RL = ∞ CL = 0 AV = 1.0 AV, Gain (dB) 100 IIB, Input Current (pA) 16 20 Figure 3. Output Saturation Voltage versus Load Current 10,000 1.0 12 IL, Load Current (mA) VS = 2.5 V RL = 100 k TA = 25°C Amp = 0.8 mV Gain Phase 60 0 20 60 40 100 20 140 0 180 0 0 25 50 75 100 1.0 125 10 100 1.0 k 10 k 100 k 1.0 M TA, Ambient Temperature (°C) f, Frequency (Hz) Figure 4. Input Bias Current versus Temperature Figure 5. Gain and Phase versus Frequency VS = 2.5 V RL = 10 k CL = 10 pF AV = 1.0 TA = 25°C 50 mV/Div 500 mV/Div VS = 2.5 V RL = 10 k CL = 10 pF AV = 1.0 TA = 25°C t, Time (500 ns/Div) t, Time (1.0 s/Div) Figure 6. Transient Response Figure 7. Slew Rate http://onsemi.com 5 10 M , Excess Phase (°) Vsat, Output Saturation Voltage (mV) 0 CMRR, Common Mode Rejection Ratio (dB) NCS2002, NCV2002 Vout, Output Voltage (Vpp) 10 8.0 VS = ±3.5 V 6.0 VS = ±2.5 V AV = 1.0 RL = 10 k TA = 25°C 4.0 2.0 VS = ±0.45 V 0 1.0 k 10 k 100 k f, Frequency (Hz) 1.0 M 90 80 VS = ±2.5 V RL = ∞ AV = 1.0 TA = 25°C 70 60 50 40 30 20 10 0 10 |ISC|, Output Short Circuit Current (mA) 120 VS = ±2.5 V RL = ∞ AV = 1.0 TA = 25°C 100 PSR + 80 PSR − 60 40 20 0 10 1.0 k 10 k 100 k 1.0 M Output Pulsed Test at 3% Duty Cycle 240 10 M −40°C 25°C 200 160 85°C 120 80 40 10 M 0 ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 f, Frequency (Hz) VS, Supply Voltage (V) Figure 10. Power Supply Rejection Ratio versus Frequency Figure 11. Output Short Circuit Sinking Current versus Supply Voltage 200 ±3.5 1.0 Output Pulsed Test at 3% Duty Cycle −40°C 160 25°C 120 85°C 80 40 0 1.0 M 280 0 100 1.0 k 10 k 100 k f, Frequency (Hz) Figure 9. Common Mode Rejection Ratio versus Frequency |ID|, Supply Current (mA) |ISC|, Output Short Circuit Current (mA) PSRR, Power Supply Rejection Ratio (dB) Figure 8. Output Voltage versus Frequency 100 0 ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 0.8 −40°C 0.6 0.4 RL = ∞ AV = 1.0 0.2 0 ±3.5 85°C 25°C 0 ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 VS, Supply Voltage (V) VS, Supply Voltage (V) Figure 12. Output Short Circuit Sourcing Current versus Supply Voltage Figure 13. Supply Current versus Supply Voltage with No Load http://onsemi.com 6 ±3.5 NCS2002, NCV2002 10 THD, Total Harmonic Distortion (%) THD, Total Harmonic Distortion (%) 10 AV = 1000 1.0 AV = 100 VS = ±0.5 V Vout = 0.4 Vpp RL = 2.0 k TA = 25°C 0.1 AV = 10 AV = 1.0 0.01 10 100 1.0 k 10 k AV = 1000 1.0 AV = 100 0.1 0.01 100 k f, Frequency (Hz) 1.0 k f, Frequency (Hz) Figure 14. Total Harmonic Distortion versus Frequency with 1.0 V Supply Figure 15. Total Harmonic Distortion versus Frequency with 1.0 V Supply 10 AV = 100 AV = 10 VS = ±2.5 V Vout = 4.0 Vpp RL = 2.0 k TA = 25°C 0.01 AV = 1.0 0.001 10 100 1.0 k 10 k THD, Total Harmonic Distortion (%) THD, Total Harmonic Distortion (%) 1.0 1.0 AV = 100 0.1 AV = 10 VS = ±2.5 V Vout = 4.0 Vpp RL = 10 k TA = 25°C 0.01 AV = 1.0 0.001 10 100 k 100 1.0 k 10 k 100 k f, Frequency (Hz) Figure 16. Total Harmonic Distortion versus Frequency with 5.0 V Supply Figure 17. Total Harmonic Distortion versus Frequency with 5.0 V Supply 3.0 GBW, Gain Bandwidth Product (MHz) +Slew Rate, VS = ±2.5 V 1.3 SR, Slew Rate (V/µs) 100 k f, Frequency (Hz) 1.4 −Slew Rate, VS = ±2.5 V 1.2 +Slew Rate, VS = ±0.5 V 1.1 −Slew Rate, VS = ±0.5 V 0.8 RL = 10 k CL = 10 pF AV = 1.0 0.7 0.6 0.5 −50 10 k AV = 1000 1.5 0.9 100 10 AV = 1000 1.0 AV = 10 AV = 1.0 10 0.1 VS = ±0.5 V Vout = 0.4 Vpp RL = 10 k TA = 25°C −25 0 25 50 75 100 125 VS = ±2.5 V RL = 10 k CL = 10 pF 2.0 1.0 0 −50 −25 0 25 50 75 100 TA, Ambient Temperature (°C) TA, Ambient Temperature (°C) Figure 18. Slew Rate versus Temperature Figure 19. Gain Bandwidth Product versus Temperature http://onsemi.com 7 125 NCS2002, NCV2002 60 100 100 60 Phase Margin VS = ±0.5 V RL = 100 k TA = 25°C Amp = 0.8 mV −20 −40 10 k 100 k 140 60 180 40 220 20 1.0 M VS = ±2.5 V RL = 10 k CL = 10 pF Gain Margin 20 0 25 50 75 0 125 100 TA, Ambient Temperature (°C) Figure 20. Voltage Gain and Phase versus Frequency Figure 21. Gain and Phase Margin versus Temperature 100 100 100 Phase Margin 80 80 VS = ±2.5 V RL = 10 k CL = 10 pF TA = 25°C 60 40 60 40 Gain Margin m, Phase Margin (°) Am, Gain Margin (dB) Phase Margin Am, Gain Margin (dB) −25 f, Frequency (Hz) 100 20 20 100 10 1.0 k 10 k 80 80 VS = ±2.5 V RL = 10 k AV = 100 TA = 25°C 60 40 60 40 Gain Margin 20 20 0 1.0 0 100 k 0 1.0 60 40 0 −50 260 100 M 10 M 80 m, Phase Margin (°) VS = ±2.5 V 0 80 0 1000 Rt, Differential Source Resistance () 10 100 CL, CapacitIve Load (pF) Figure 22. Gain and Phase Margin versus Differential Source Resistance Figure 23. Gain and Phase Margin versus Output Load Capacitance 100 8.0 m, Phase Margin (°) AV, Gain (dB) VS = ±0.5 V 20 100 m, Excess Phase (°) Am, Gain Margin (dB) VS = ±2.5 V 40 100 6.0 4.0 2.0 RL = 10 k AV = 100 TA = 25°C 80 60 60 40 40 Gain Margin 20 20 0 0 0 ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 ±3.5 0 ±0.5 0 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 VS, Supply Voltage (V) VS, Supply Voltage (V) Figure 24. Output Voltage Swing versus Supply Voltage Figure 25. Gain and Phase Margin versus Supply Voltage http://onsemi.com 8 ±3.5 m, Phase Margin (°) Am, Gain Margin (dB) Vout, Output Voltage (Vpp) Phase Margin 80 NCS2002, NCV2002 20 VIO, Input Offset Voltage (mV) AVOL, Open Loop Voltage Gain (dB) 100 80 60 40 RL = 10 k TA = 25°C 20 0 0 ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 10 5 0 −5 −10 −15 −20 −3.0 ±3.5 −2.0 0 1.0 2.0 3.0 VCM, Common Voltage Range (V) Figure 26. Open Loop Voltage Gain versus Supply Voltage Figure 27. Input Offset Voltage versus Common Mode Input Voltage Range, VS = 2.5 V 3.0 15 10 5 VCM, Input Common Mode Voltage Range (V) VS = ±0.9 V RL = ∞ CL = 0 AV = 1.0 TA = 25°C 0 −5 −10 −15 −20 −1.0 −0.8 −0.6 −0.4 −0.2 2.0 1.0 VIO = 5.0 mV RL = ∞ CL = 0 AV = 1.0 TA = 25°C 0 −1.0 −2.0 −3.0 0 0.2 0.4 0.6 0.8 1.0 ±0.5 0 VCM, Common Mode Input Voltage (V) ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 VS, Supply Voltage (V) Figure 28. Input Offset Voltage versus Common Mode Input Voltage Range, VS = 0.9 V Figure 29. Common−Mode Input Voltage Range versus Power Supply Voltage 3.0 VEN, Enable Input Voltage (V) 4.0 2.5 ICC, Supply Current (A) −1.0 VS, Supply Voltage (V) 20 VIO, Input Offset Voltage (mV) VS = ±2.5 V RL = ∞ CL = 0 AV = 1.0 TA = 25°C 15 2.0 1.5 1.0 RL = ∞ AV = 1.0 TA = 25°C 0.5 0 3.5 VEN(on) 3.0 2.5 2.0 VEN(off) 1.5 1.0 AV = ∞ TA = 25°C 0.5 0 0 ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 ±3.5 0 ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 VS, Supply Voltage (V) VS, Supply Voltage (V) Figure 30. Supply Current versus Supply Voltage (Disabled) Figure 31. Enable Input Voltage versus Supply Voltage http://onsemi.com 9 ±3.5 NCS2002, NCV2002 16 RL = 10 k TA = 25°C Propagation Delay (S) 14 12 10 8.0 ton 6.0 4.0 toff 2.0 0 0 ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 ±3.5 VS, SUPPLY VOLTAGE (V) Figure 32. Propagation Delay versus Supply Voltage APPLICATION INFORMATION AND OPERATING DESCRIPTION GENERAL INFORMATION The NCS2002 is an industry first rail−to−rail input, rail−to−rail output amplifier that features guaranteed sub one volt operation. This unique feature set is achieved with the use of a modified analog CMOS process that allows the implementation of depletion MOSFET devices. The amplifier has a 1.0 MHz gain bandwidth product, 1.2 V/s slew rate and is operational over a power supply range less than 0.9 V to as high as 7.0 V. The ultra low input bias current of the NCS2002 allows the use of extremely high value source and feedback resistor without reducing the amplifier’s gain accuracy. These high value resistors, in conjunction with the device input and printed circuit board parasitic capacitances C in, will add an additional pole to the single pole amplifier in Figure 33. If low enough in frequency, this additional pole can reduce the phase margin and significantly increase the output settling time. The effects of Cin, can be canceled by placing a zero into the feedback loop. This is accomplished with the addition of capacitor Cfb. An approximate value for Cfb can be calculated by: Inputs The input topology chosen for this device series is unconventional when compared to most low voltage operational amplifiers. It consists of an N−channel depletion mode differential transistor pair that drives a folded cascade stage and current mirror. This configuration extends the input common mode voltage range to encompass the VEE and VCC power supply rails, even when powered from a combined total of less than 0.9 volts. Figures 27, 28 and 29 show the input common mode voltage range versus power supply voltage. The differential input stage is laser trimmed in order to minimize offset voltage. The N−channel depletion mode MOSFET input stage exhibits an extremely low input bias current of less than 10 pA. The input bias current versus temperature is shown in Figure 4. Either one or both inputs can be biased as low as VEE minus 300 mV to as high as 7.0 V without causing damage to the device. If the input common mode voltage range is exceeded, the output will not display a phase reversal. If the maximum input positive or negative voltage ratings are to be exceeded, a series resistor must be used to limit the input current to less than 2.0 mA. Cfb Rin Cin Rfb Cfb Rfb Rin Input Cin − + Output Cin = Input and printed circuit board capacitance Figure 33. Input Capacitance Pole Cancellation http://onsemi.com 10 NCS2002, NCV2002 Output The output stage consists of complimentary P and N channel devices connected to provide rail−to−rail output drive. With a 2.0 k load, the output can swing within 50 mV of either rail. It is also capable of supplying over 75 mA when powered from 5.0 V and 1.0 mA when powered from 0.9 V. When connected as a unity gain follower, the NCS2002 can directly drive capacitive loads in excess of 820 pF at room temperature without oscillating but with significantly reduced phase margin. The unity gain follower configuration exhibits the highest bandwidth and is most prone to oscillations when driving a high value capacitive load. The capacitive load in combination with the amplifier’s output impedance, creates a phase lag that can result in an under−damped pulse response or a continuous oscillation. Figure 35 shows the effect of driving a large capacitive load in a voltage follower type of setup. When driving capacitive loads exceeding 820 pF, it is recommended to place a low value isolation resistor between the output of the op amp and the load, as shown in Figure 34. The series resistor isolates the capacitive load from the output and enhances the phase margin. Refer to Figure 36. Larger values of R will result in a cleaner output waveform but excessively large values will degrade the large signal rise and fall time and reduce the output amplitude. Depending upon the capacitor characteristics, the isolation resistor value will typically be between 50 to 500 . The output drive capability for resistive and capacitive loads is shown in Figures 2, 3, and 23. Input + − R Output CL Isolation resistor R = 50 to 500 Figure 34. Capacitance Load Isolation Note that the lowest phase margin is observed at cold temperature and low supply voltage. Enable Pin The enable pin allows the user to externally control the device. if the enable pin is pulled below the input disable threshold voltage (VEN < 45% VCC), the amplifier is disabled. Once the enable pin is taken above the threshold voltage (VEN = 60% VCC), the amplifier will turn on. In the event the enable pin is not connected, the amplifier will remain on by default http://onsemi.com 11 NCS2002, NCV2002 Vin VS = ±0.45 V Vin = 0.8 Vpp R=0 CL = 820 pF AV = 1.0 TA = 25°C Vout Figure 35. Small Signal Transient Response with Large Capacitive Load Vin VS = ±0.45 V Vin = 0.8 Vpp R = 51 CL = 820 pF AV = 1.0 TA = 25°C Vout Figure 36. Small Signal Transient Response with Large Capacitive Load and Isolation Resistor. http://onsemi.com 12 NCS2002, NCV2002 RT 470 k VCC Output Voltage 0 0.9 V CT 1.0 nF Timing Capacitor Voltage − fO = 1.5 kHz + The non−inverting input threshold levels are set so that the capacitor voltage oscillates between 1/3 and 2/3 of VCC. This requires the resistors R1a, R1b and R2 to be of equal value. The following formula can be used to approximate the output frequency. R1a 470 k 0.9 V R2 470 k R1b 470 k 0.67 VCC 0.33 VCC 1 f O 1.39 R TC T Figure 37. 0.9 V Square Wave Oscillator cww D1 1N4148 10 k VCC Output Voltage 0 1.0 M D2 1N4148 10 k Timing Capacitor Voltage 0.67 VCC 0.33 VCC cw Clock−wise, Low Duty Cycle VCC CT 1.0 nF VCC Output Voltage − 0 fO + Timing Capacitor Voltage R1a 470 k 0.67 VCC 0.33 VCC Counter−Clock−wise, High Duty Cycle VCC R1b 470 k R2 470 k The timing capacitor CT will charge through diode D2 and discharge through diode D1, allowing a variable duty cycle. The pulse width of the signal can be programmed by adjusting the value of the trimpot. The capacitor voltage will oscillate between 1/3 and 2/3 of VCC, since all the resistors at the non−inverting input are of equal value. Figure 38. Variable Duty Cycle Pulse Generator http://onsemi.com 13 NCS2002, NCV2002 R1 1.0 M 2.5 V R3 1.0 k + − Cin 10 F ≈ 10,000 µF −2.5 V Ceff. R2 1.0 M R1 C R3 in Figure 39. Positive Capacitance Multiplier Af Cf 400 pF Rf 100 k fL R2 10 k 0.5 V 1 f 200 Hz L 2R C 1 1 + − Vin C1 80 nF fH VO R1 10 k −0.5 V 1 f 4.0 kHz H 2RC f f R A 1 f 11 f R2 Figure 40. 1.0 V Voiceband Filter http://onsemi.com 14 NCS2002, NCV2002 Vsupply VCC Vin + I − V in sink R sense Rsense Figure 41. High Compliance Current Sink Is VL 1.0 V Rsense RL R3 1.0 k R1 1.0 k R4 + − 1.0 k R5 VO 2.4 k 75 Is VO 435 mA 34.7 mV 212 mA 36.9 mV R6 For best performance, use low tolerance resistors. R2 3.3 k Figure 42. High Side Current Sense http://onsemi.com 15 NCS2002, NCV2002 PACKAGE DIMENSIONS TSOP−6 CASE 318G−02 ISSUE I NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. A L 6 S 1 5 4 2 3 B D G M J C 0.05 (0.002) H K DIM A B C D G H J K L M S MILLIMETERS MIN MAX 2.90 3.10 1.30 1.70 0.90 1.10 0.25 0.50 0.85 1.05 0.013 0.100 0.10 0.26 0.20 0.60 1.25 1.55 0 10 2.50 3.00 INCHES MIN MAX 0.1142 0.1220 0.0512 0.0669 0.0354 0.0433 0.0098 0.0197 0.0335 0.0413 0.0005 0.0040 0.0040 0.0102 0.0079 0.0236 0.0493 0.0610 0 10 0.0985 0.1181 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 16 For additional information, please contact your local Sales Representative. NCS2002/D