Order this document by MC33206/D The MC33206/7 family of operational amplifiers provide rail–to–rail operation on both the input and output. The inputs can be driven as high as 200 mV beyond the supply rails without phase reversal on the outputs and the output can swing within 50 mV of each rail. This rail–to–rail operation enables the user to make full use of the supply voltage range available. It is designed to work at very low supply voltages (±0.9 V) yet can operate with a single supply of up to 12 V and ground. Output current boosting techniques provide a high output current capability while keeping the drain current of the amplifier to a minimum. The MC33206/7 has an enable mode that can be controlled externally. The typical supply current in the standby mode is <1.0 µA (VEnable = Gnd). The addition of an enable function makes this amplifier an ideal choice for power sensitive applications, battery powered equipment (instrumentation and monitoring), portable telecommunication, and sample–and–hold applications. • • • • • • • • • LOW VOLTAGE RAIL–TO–RAIL OPERATIONAL AMPLIFIERS SEMICONDUCTOR TECHNICAL DATA MC33206 P SUFFIX PLASTIC PACKAGE CASE 646 14 1 D SUFFIX PLASTIC PACKAGE CASE 751A (SO–14) 14 Standby Mode (ID ≤1.0 µA, Typ) 1 Low Voltage, Single Supply Operation (1.8 V and Ground to 12 V and Ground) N.C. 1 14 N.C. N.C. 2 13 VCC Rail–to–Rail Input Common Mode Voltage Range Output 1 3 Output Voltage Swings within 50 mV of both Rails 4 Inputs 1 No Phase Reversal on the Output for Over–Driven Input Signals 12 Output 2 1 11 2 Inputs 2 5 10 Enable 1 6 9 Enable 2 VEE 7 8 N.C. High Output Current (ISC = 80 mA, Typ) Low Supply Current (ID = 0.9 mA, Typ) (Dual, Top View) 600 Ω Output Drive Capability MC33207 Typical Gain Bandwidth Product = 2.2 MHz P SUFFIX PLASTIC PACKAGE CASE 648 16 1 D SUFFIX PLASTIC PACKAGE CASE 751B (SO–16) 16 1 Output 1 1 16 Enable 1, 4 15 Output 4 2 Inputs 1 ORDERING INFORMATION 3 1 14 4 Operational Amplifier Function Device Operating Temperature Range Package 5 Inputs 2 MC33206D SO–14 Dual MC33206P MC33207D TA= –40 40 ° to +105°C 105°C Plastic DIP SO–16 6 11 3 10 Enable 2, 3 8 9 Inputs 3 Output 3 (Quad, Top View) Plastic DIP Motorola, Inc. 1999 MOTOROLA ANALOG IC DEVICE DATA Inputs 4 12 VEE 2 Output 2 7 Quad MC33207P 13 VCC 4 Rev 1 1 MC33206 MC33207 MAXIMUM RATINGS Rating Symbol Value Unit VS 13 V VESD 2,000 V Voltage at any Device Pin VDP VS ± 0.5 V Input Differential Voltage Range VIDR (Note 1) V Common Mode Input Voltage Range (Note 2) VCM VCC + 0.5 to VEE – 0.5 V Output Short Circuit Duration (Note 3) ts (Note 3) sec Maximum Junction Temperature TJ +150 °C Storage Temperature Range Tstg –65 to +150 °C Maximum Power Dissipation PD (Note 3) mW Supply Voltage (VCC to VEE) ESD Protection Voltage at any Pin Human Body Model NOTES: 1. The differential input voltage of each amplifier is limited by two internal parallel back–to–back diodes. For additional differential input voltage range, use current limiting resistors in series with the input pins. 2. The common–mode input voltage range of each amplifier is limited by diodes connected from the inputs to both power supply rails. Therefore, the voltage on either input must not exceed either supply rail by more than 500 mV. 3. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded. 4. ESD data available upon request. DC ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = 0 V, VEnable = 5.0 V, TA = 25°C, unless otherwise noted.) Characteristic Figure Symbol Min Typ Max Input Offset Voltage (VCM 0 to 0.5 V, VCM 1.0 to 5.0 V) MC33206: TA = 25°C MC33201: TA = –40° to +105°C MC33207: TA = 25°C MC33202: TA = –40° to +105°C – VIO Input Offset Voltage Temperature Coefficient (RS = 50 Ω) TA = –40° to +105°C – ∆VIO/∆T Input Bias Current (VCM = 0 to 0.5 V, VCM = 1.0 to 5.0 V) TA = 25°C TA = –40° to +105°C – IIB Input Offset Current (VCM = 0 to 0.5 V, VCM = 1.0 to 5.0 V) TA = 25°C TA = –40° to +105°C – Common Mode Input Voltage Range – VICR Large Signal Voltage Gain (VCC = 5.0 V, VEE = –5.0 V) RL = 10 kΩ RL = 600 Ω – AVOL Output Voltage Swing (VID = ±0.2 V) RL = 10 kΩ RL = 10 kΩ RL = 600 Ω RL = 600 Ω – Common Mode Rejection (Vin = 0 to 5.0 V) – – – – 0.5 1.0 0.5 1.0 8.0 11 10 13 – 2.0 – – – 80 100 200 250 – – 5.0 10 50 100 – VEE VCC + 0.2 VEE – 0.2 VCC – 50 25 300 250 – – VOH VOL VOH VOL 4.85 – 4.75 – 4.95 0.05 4.85 0.15 – 0.15 – 0.25 – CMR 60 90 – dB Power Supply Rejection Ratio VCC/VEE = 5.0 V/Gnd to 3.0 V/Gnd – PSRR PSR – 66 25 92 500 – µV/V dB Output Short Circuit Current (Source and Sink) – ISC 50 80 – mA 2 Unit mV µV/°C nA IIO nA V kV/V V MOTOROLA ANALOG IC DEVICE DATA MC33206 MC33207 DC ELECTRICAL CHARACTERISTICS (continued) (VCC = 5.0 V, VEE = 0 V, VEnable = 5.0 V, TA = 25°C, unless otherwise noted.) Characteristic Figure Symbol Power Supply Current (VO = 2.5 V, TA = –40° to +105°C, per Amplifier) MC33206: VEnable = 5.0 Vdc MC33206: VEnable = Gnd (Standby) MC33207: VEnable = 5.0 Vdc MC33207: VEnable = Gnd (Standby) – ID Enable Input Voltage (per Amplifier) Enabled – Amplifier “On” Disabled – Amplifier “Off” (Standby) – Enable Input Current (Note 5) (per Amplifier) VEnable = 12 V VEnable = 5.0 V VEnable = 1.8 V VEnable = Gnd – NOTE: Min Typ Max Unit – – – – 0.8 0.5 1.5 0.5 1.125 6.0 2.25 6.0 mA µA mA µA – – VEE + 1.8 VEE + 0.3 – – – – – – 2.5 2.2 0.8 0 – – – – VEnable V µA IEnable 5. External control circuitry must provide for an initial turn–off transient of <10 µA. AC ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = 0 V, VEnable = 5.0 V, TA = 25°C, unless otherwise noted.) Figure Symbol Min Typ Max Unit Slew Rate (VS = ±2.5 V, VO = –2.0 to +2.0 V, RL = 2.0 kΩ, AV = 1.0) – SR 0.5 1.0 – V/µs Gain Bandwidth Product (f = 100 kHz) – GBW – 2.2 – MHz Phase Margin (RL = 600 Ω, CL = 0 pF) – OM – 65 – Deg Gain Margin (RL = 600 Ω, CL = 0 pF) – AM – 12 – dB Channel Separation (f = 1.0 Hz to 20 kHz, AV = 100) – CS – 90 – dB Power Bandwidth (VO = 4.0 Vpp, RL = 600 Ω, THD ≤ 1%) – BWP – 28 – kHz – THD – – 0.002 0.008 – – Characteristic Total Harmonic Distortion (RL = 600 Ω, VO = 1.0 Vpp, AV = 1.0) f = 1.0 kHz f = 10 kHz % Open Loop Output Impedance (VO = 0 V, f = 2.0 MHz, AV = 10) – ZO – 100 – Ω Differential Input Resistance (VCM = 0 V) – Rin – 200 – kΩ Differential Input Capacitance (VCM = 0 V) – Cin – 8.0 – pF Equivalent Input Noise Voltage (RS = 100 Ω) f = 10 Hz f = 1.0 kHz – en – – 25 20 – – Equivalent Input Noise Current f = 10 Hz f = 1.0 kHz – – – 0.8 0.2 – – Time Delay for Device to Turn On – ton – 10 – µs Time Delay for Device to Turn Off – toff – 2.0 – µs MOTOROLA ANALOG IC DEVICE DATA in nV/ Hz pA/ Hz 3 MC33206 MC33207 Figure 1. Circuit Schematic (Each Amplifier) VCC VCC Enable VCC VCC Vin – Vin + VEE Figure 2. Maximum Power Dissipation versus Temperature Figure 3. Input Offset Voltage Distribution 4000 40 3500 PERCENTAGE OF AMPLIFIERS (%) PD(max) , MAXIMUM POWER DISSIPATION (mW) This device contains 96 active transistors (each amplifier). 16 Pin DIP 3000 2500 2000 14 Pin DIP 1500 1000 4 500 0 –60 SO–14/SO–1 6 –30 0 30 60 90 TA, AMBIENT TEMPERATURE (°C) 120 150 35 30 25 360 amplifiers tested from 3 wafer lots VCC = 5.0 V VEE = Gnd TA = 25°C DIP Package 20 15 10 5.0 0 –10 –8.0 –6.0 –4.0 –2.0 0 2.0 4.0 6.0 VIO, INPUT OFFSET VOLTAGE (mV) 8.0 10 MOTOROLA ANALOG IC DEVICE DATA MC33206 MC33207 Figure 4. Input Offset Voltage Temperature Coefficient Distribution Figure 5. Input Bias Current versus Temperature 200 360 amplifiers tested from 3 wafer lots VCC = 5.0 V VEE = Gnd TA = 25°C DIP Package 40 30 I IB , INPUT BIAS CURRENT (nA) PERCENTAGE OF AMPLIFIERS (%) 50 160 120 20 10 0 –50 –40 –30 –20 –10 0 10 20 30 40 VCC = 5.0 V VEE = Gnd VCM = 0 V to 0.5 V 80 VCM > 1.0 V 40 0 –55 –40 –25 50 0 TCVIO, INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT (µV/°C) A VOL , OPEN LOOP VOLTAGE GAIN (kV/V) I IB , INPUT BIAS CURRENT (nA) 100 50 0 –50 –100 –250 VCC = 12 V VEE = Gnd TA = 25°C 0 2.0 4.0 6.0 8.0 10 VCM, INPUT COMMON MODE VOLTAGE (V) 12 260 220 180 VCC = 5.0 V VEE = Gnd RL = 600 Ω ∆VO = 0.5 V to 4.5 V 140 100 –55 –40 –25 RL = 600 Ω TA = 25°C 8.0 6.0 4.0 2.0 0 ±1.0 ±2.0 ±3.0 ±4.0 ±5.0 VCC,VEE SUPPLY VOLTAGE (V) MOTOROLA ANALOG IC DEVICE DATA 0 25 70 85 TA, AMBIENT TEMPERATURE (°C) 105 125 Figure 9. Output Saturation Voltage versus Load Current VCC VSAT, OUTPUT SATURATION VOLTAGE (V) VO,OUTPUT VOLTAGE (Vpp) 10 125 300 Figure 8. Output Voltage Swing versus Supply Voltage 12 85 Figure 7. Open Loop Voltage Gain versus Temperature 150 –200 70 TA, AMBIENT TEMPERATURE (°C) Figure 6. Input Bias Current versus Common Mode Voltage –150 25 ±6.0 TA = –55°C TA = 125°C VCC – TA = 25°C VCC – VCC = 5.0 V VEE = –5.0 V VEE + TA = 25°C TA = 125°C TA = –55°C 0 5.0 10 IL, LOAD CURRENT (mA) 15 VEE + VEE 20 5 MC33206 MC33207 Figure 10. Output Voltage versus Frequency Figure 11. Common Mode Rejection versus Frequency CMR, COMMON MODE REJECTION (dB) VO, OUTPUT VOLTAGE (Vpp) 12 9.0 6.0 VCC = 6.0 V VEE = –6.0 V RL = 600 Ω AV = 1.0 TA = 25°C 3.0 0 1.0 k ISC , OUTPUT SHORT CIRCUIT CURRENT (mA) PSR, POWER SUPPLY REJECTION (dB) 100 PSR+ 80 60 PSR– 40 VCC = 6.0 V VEE = –6.0 V TA = –55° to +125°C 0 10 40 100 1.0 k 10 k f, FREQUENCY (Hz) 100 k VCC = 6.0 V VEE = –6.0 V TA = –55° to +125°C 20 10 Source 60 Sink 40 VCC = 6.0 V VEE = –6.0 V TA = 25°C 20 0 0 Source Sink 25 0 25 70 85 TA, AMBIENT TEMPERATURE (°C) 1.0 2.0 3.0 4.0 5.0 6.0 Figure 15. Supply Current per Amplifier versus Supply Voltage with No Load 50 0 –55 –40 –25 1.0 M Vout, OUTPUT VOLTAGE (V) VCC = 5.0 V VEE = Gnd 75 100 k 80 1.0 M 150 100 1.0 k 10 k f, FREQUENCY (Hz) 100 Figure 14. Output Short Circuit Current versus Temperature 125 100 Figure 13. Output Short Circuit Current versus Output Voltage I CC, SUPPLY CURRENT PER AMPLIFIER (mA) ISC , OUTPUT SHORT CIRCUIT CURRENT (mA) 60 1.0 M 120 6 80 0 10 k 100 k f, FREQUENCY (Hz) Figure 12. Power Supply Rejection versus Frequency 20 100 105 125 2.0 1.6 TA = 125°C 1.2 TA = 25°C 0.8 TA = –55°C 0.4 0 ±0 ±1.0 ±2.0 ±3.0 ±4.0 ±5.0 VCC, VEE, SUPPLY VOLTAGE (V) ± .0 MOTOROLA ANALOG IC DEVICE DATA MC33206 MC33207 Figure 16. Slew Rate versus Temperature Figure 17. Gain Bandwidth Product versus Temperature +Slew Rate 1.0 –Slew Rate 0.5 0 25 70 85 105 2.0 1.0 0 –55 –40 –25 0 Figure 19. Voltage Gain and Phase versus Frequency 40 VS = ±6.0 V TA = 25°C RL = 600 Ω 80 120 1A 2A 10 160 2B 1A – Phase, CL = 0 pF 1B – Gain, CL = 0 pF 2A – Phase, CL = 300 pF 2B – Gain, CL = 300 pF –30 10 k 1B 100 k 200 240 10 M 1.0 M 70 50 30 80 1A 10 1B 1A – Phase, VS = ±6.0 V 1B – Gain, VS = ±6.0 V 2A – Phase, VS = ±1.0 V 2B – Gain, VS = ±1.0 V –10 –30 10 k 120 160 2B 200 100 k 240 10 M 1.0 M Figure 21. Gain and Phase Margin versus Differential Source Resistance 75 70 50 50 VCC = 6.0 V VEE = –6.0 V RL = 600 Ω CL = 100 pF 40 30 20 20 10 10 Gain Margin 70 0 85 TA, AMBIENT TEMPERATURE (°C) MOTOROLA ANALOG IC DEVICE DATA 105 125 O M , PHASE MARGIN (DEGREES) 60 A , GAIN MARGIN (dB) M 60 75 Phase Margin Phase Margin 25 40 f, FREQUENCY (Hz) 70 0 125 2A Figure 20. Gain and Phase Margin versus Temperature 0 –55 –40 –25 105 CL = 0 pF TA = 25°C RL = 600 Ω f, FREQUENCY (Hz) O M , PHASE MARGIN (DEGREES) 85 Figure 18. Voltage Gain and Phase versus Frequency 30 30 70 TA, AMBIENT TEMPERATURE (°C) 50 40 25 TA, AMBIENT TEMPERATURE (°C) 70 –10 VCC = 2.5 V VEE = –2.5 V f = 100 kHz 3.0 125 O , EXCESS PHASE (DEGREES) A VOL, OPEN LOOP VOLTAGE GAIN (dB) 0 –55 –40 –25 4.0 GBW, GAIN BANDWIDTH PRODUCT (MHz) 1.5 VCC = 2.5 V VEE = –2.5 V VO = ±2.0 V A VOL, OPEN LOOP VOLTAGE GAIN (dB) SR, SLEW RATE (V/µ s) 2.0 60 60 VCC = 6.0 V VEE = –6.0 V TA = 25°C 45 45 30 30 15 15 Gain Margin 0 10 100 1.0 k 10 k 0 100 k RT, DIFFERENTIAL SOURCE RESISTANCE (Ω) 7 MC33206 MC33207 Figure 23. Output Voltage versus Load Resistance Figure 22. Gain and Phase Margin versus Capacitive Load 60 50 Gain Margin 14 12 10 40 8.0 30 6.0 20 4.0 10 2.0 0 10 0 100 VCC = 5.0 Vdc 4.0 3.0 2.0 0 10 1.0 k VCC = 2.0 Vdc VEE = Gnd CL = 0 pF AV = 1.0 TA = 25°C 1.0 100 CL, CAPACITIVE LOAD (pF) THD, TOTAL HARMONIC DISTORTION (%) AV = 100 90 AV = 10 30 0 100 VCC = 6.0 V VEE = –6.0 V VO = 8.0 Vpp TA = 25°C 1.0 k 10 1.0 VCC = 5.0 V TA = 25°C VO = 2.0 Vpp AV = 1000 AV = 100 0.1 AV = 10 0.01 AV = 1.0 0.001 10 10 k VEE = –5.0 V RL = 600 Ω 100 f, FREQUENCY (Hz) en , EQUIVALENT INPUT NOISE VOLTAGE (nV/ Hz) CS, CHANNEL SEPARATION (dB) 150 60 1.0 k 10 k 100 k f, FREQUENCY (Hz) Figure 26. Equivalent Input Noise Voltage and Current versus Frequency 50 5.0 VCC = 6.0 V VEE = –6.0 V TA = 25°C 40 30 4.0 3.0 Noise Voltage 20 10 2.0 1.0 Noise Current 0 10 100 k Figure 25. Total Harmonic Distortion versus Frequency Figure 24. Channel Separation versus Frequency 120 1.0 k 10 k RL, LOAD RESISTANCE 100 1.0 k 10 k 0 100 k i n , INPUT REFERRED NOISE CURRENT (pA/ Hz) Phase Margin VO , OUTPUT VOLTAGE (Vpp) 70 5.0 16 VCC = 6.0 V VEE = –6.0 V RL = 600 Ω AV = 100 TA = 25°C A , GAIN MARGIN (dB) M O M , PHASE MARGIN (DEGREES) 80 f, FREQUENCY (Hz) 8 MOTOROLA ANALOG IC DEVICE DATA MC33206 MC33207 Figure 28. ton Response The MC33206/7 family of operational amplifiers are unique in their ability to swing rail–to–rail on both the input and the output with a completely bipolar design. This offers low noise, high output current capability and a wide common mode input voltage range even with low supply voltages. Operation is guaranteed over an extended temperature range and at supply voltages of 2.0 V, 3.3 V and 5.0 V and ground. Since the common mode input voltage range extends from VCC to VEE, it can be operated with either single or split voltage supplies. The MC33206/7 are guaranteed not to latch or phase reverse over the entire common mode range, however, the inputs should not be allowed to exceed maximum ratings. VO (1.0 V/DIV), V in (2.0 V/DIV) GENERAL INFORMATION ton, TIME (2.0 µs/DIV) CIRCUIT INFORMATION Enable Function The MC33206/07 enable pins allow the user to externally control the device. (Refer to the Pin Diagram on the first page of this data sheet for enable pin connections.) If the enable pins are pulled low (Gnd) each amplifier (MC33206) and amplifier pair (MC33207) will be disabled. When the enable pins are at a logic high (VEnable ≥ VEE = 1.8 V) the amplifiers will turn “on”. Refer to the data sheet characteristics for the required levels needed to change logical state. The time to change states (from device “on” to “off” and “off” to “on”) is defined as the time delay. The Circuit in Figure 27 is used to measure ton and toff. Typical ton and toff measurements are shown in Figures 28 and 29. When the device is turned off (VEnable = Gnd) an internal regulator is shut off disabling the amplifier. Figure 27. Test Circuit for ton and toff VCC Vout MC33206 2.0 V 2.0 k VEnable ton toff MOTOROLA ANALOG IC DEVICE DATA ton toff Figure 29. toff Response VO (1.0 V/DIV), V in (2.0 V/DIV) Rail–to–rail performance is achieved at the input of the amplifiers by using parallel NPN–PNP differential input stages. When the inputs are within 800 mV of the negative rail, the PNP stage is on. When the inputs are more than 800 mV greater than VEE, the NPN stage is on. This switching of input pairs will cause a reversal of input bias currents (see Figure 6). Also, slight differences in offset voltage may be noted between the NPN and PNP pairs. Cross–coupling techniques have been used to keep this change to a minimum. In addition to its rail–to–rail performance, the output stage is current boosted to provide 80 mA of output current, enabling the op amp to drive 600 Ω loads. Because of this high output current capability, care should be taken not to exceed the 150°C maximum junction temperature. toff, TIME (2.0 µs/DIV) Low Voltage Operation The MC33206/07 will operate at supply voltages down to 1.8 V and ground. Since this device is a rail–to–rail on both the input and output, one can be assured of continued operation in battery applications when battery voltages drop to low voltage levels. This is called End of Discharge (see Figure 30). Now, the user can select a minimum quantity of batteries best suited for the particular design depending on the type of battery chosen. This will minimize part count in many designs. Figure 30. Typical Battery Characteristics Type Operating Voltage End of Discharge Alkaline NiCd NiMh Silver Oxide Lithium Ion 1.5 V 1.2 V 1.2 V 1.6 V 3.6 V 0.9 V 1.0 V 1.0 V 1.3 V 2.5 V Compensating for Output Capacitance The combination of device output impedance and increasing capacitive loading will cause phase delay (reducing the phase margin) in any amplifier (Figure 22). If the loading is excessive, the resulting response can be circuit oscillation. In other words, an amplifier can become unstable when the phase becomes greater than 180 degrees before the open loop gain drops to unity gain. Figures 18 and 19 show this situation as frequency increases for a given load. The MC33206/7 can typically drive up to 300 pF loads at unity gain without oscillating. 9 MC33206 MC33207 Figure 31. Capacitive Loads Compensation Rf CX RO CL Vin There are several ways to compensate for this phenomena. Adding series resistance to the output is one way, but not an ideal solution. A dc voltage error will occur at the output. A better design solution to compensate for higher capacitive loads would be to use the circuit in Figure 31. This design helps to counteract the loss of phase margin by taking the high frequency output signal and feeding it back into the amplifier inverting input. This technique helps to overcome oscillation due to a highly capacitive load. Keep in mind that compensation will have the affect of lowering the Gain Bandwidth Product (GPW). The values of CX and R0, are determined experimentally. Typical CX and CL will be the same value. SPICE Model If a SPICE Macromodel is desired for the MC33206/07, the user can define the characteristics from the following information. Obtain the SPICE Macromodel for the MC33204 Rail–to–Rail Operational Amplifier (device is the same as the MC33207). For the Enable feature of the MC33207, simulate it as a bipolar switch. The Macromodel does not include an input capacitance between the inverting and noninverting inputs. This capacitor is called Cin. Add 3.0 to 5.0 pF if stability analysis is required. Figure 33. Small Signal Transient Response VCC = 6.0 V VEE = –6.0 V RL = 600 Ω CL = 100 pF TA = 25°C V , OUTPUT VOLTAGE (50 mV/DIV) O V , OUTPUT VOLTAGE (2.0 mV/DIV) O Figure 32. Noninverting Amplifier Slew Rate VCC = 6.0 V VEE = –6.0 V RL = 600 Ω CL = 100 pF TA = 25°C RL t, TIME (5.0 µs/DIV) t, TIME (10 µs/DIV) V , OUTPUT VOLTAGE (2.0 V/DIV) O Figure 34. Large Signal Transient Response VCC = 6.0 V VEE = –6.0 V RL = 600 Ω CL = 100 pF AV = 1.0 TA = 25°C t, TIME (10 µs/DIV) 10 MOTOROLA ANALOG IC DEVICE DATA MC33206 MC33207 OUTLINE DIMENSIONS P SUFFIX PLASTIC PACKAGE CASE 646–06 ISSUE L 14 8 1 7 NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. B A F DIM A B C D F G H J K L M N L C J N H G D SEATING PLANE K M D SUFFIX PLASTIC PACKAGE CASE 751A–03 (SO–14) ISSUE F –A– 14 1 P 7 PL 0.25 (0.010) 7 G M B M R X 45 _ C F –T– 0.25 (0.010) M T B S A S P SUFFIX PLASTIC PACKAGE CASE 648–08 ISSUE R –A– 16 9 1 8 C L S –T– SEATING PLANE K H G D J 16 PL 0.25 (0.010) M MOTOROLA ANALOG IC DEVICE DATA T A M MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B F DIM A B C D F G J K M P R J M K D 14 PL SEATING PLANE MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0_ 10_ 0.39 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 8 –B– INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0_ 10_ 0.015 0.039 M DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 11 MC33206 MC33207 OUTLINE DIMENSIONS D SUFFIX PLASTIC PACKAGE CASE 751B–05 (SO–16) ISSUE J –A– 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 –B– 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 _ C –T– SEATING PLANE M D 16 PL 0.25 (0.010) M T B S A S J DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 JAPAN: Motorola Japan Ltd.; SPD, Strategic Planning Office, 141, 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan. 81–3–5487–8488 Customer Focus Center: 1–800–521–6274 Mfax: [email protected] – TOUCHTONE 1–602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, Motorola Fax Back System – US & Canada ONLY 1–800–774–1848 2, Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. – http://sps.motorola.com/mfax/ 852–26629298 HOME PAGE: http://motorola.com/sps/ 12 ◊ MC33206/D MOTOROLA ANALOG IC DEVICE DATA WWW.ALLDATASHEET.COM Copyright © Each Manufacturing Company. All Datasheets cannot be modified without permission. This datasheet has been download from : www.AllDataSheet.com 100% Free DataSheet Search Site. Free Download. No Register. Fast Search System. www.AllDataSheet.com