1N6266 GaAs INFRARED EMITTING DIODE FEATURES PACKAGE DIMENSIONS • Good optical to mechanical alignment 0.209 (5.31) • Mechanically and wavelength matched to the 0.184 (4.67) TO-18 series phototransistor 0.030 (0.76) NOM • Hermetically sealed package 0.255 (6.48) • High irradiance level • (*) Indicates JEDEC registered values 1.00 (25.4) MIN ANODE (CASE) SCHEMATIC DESCRIPTION • The 1N6266 is a 940 nm LED in a 0.100 (2.54) ANODE (Connected To Case) narrow angle, TO-46 package. 0.050 (1.27) CATHODE 1 0.040 (1.02) Ø0.020 (0.51) 2X 1. Derate power dissipation linearly 1.70 mW/°C above 25°C ambient. 2. Derate power dissipation linearly 13.0 mW/°C above 25°C case. 3. RMA flux is recommended. 4. Methanol or isopropyl alcohols are recommended as cleaning agents. 5. Soldering iron tip 1/16” (1.6mm) minimum from housing. 6. As long as leads are not under any stress or spring tension 45° NOTES: 1. Dimensions for all drawings are in inches (mm). 2. Tolerance of ± .010 (.25) on all non-nominal dimensions unless otherwise specified. ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise specified) Parameter Operating Temperature Symbol Rating Unit TOPR -65 to +125 °C *Storage Temperature TSTG -65 to +150 °C *Soldering Temperature (Iron)(3,4,5 and 6) TSOL-I 240 for 5 sec °C (Flow)(3,4 and 6) TSOL-F 260 for 10 sec °C IF 100 mA *Forward Current (pw, 1µs; 200Hz) IF 10 A *Reverse Voltage VR 3 V *Power Dissipation (TA = 25°C)(1) PD 170 mW Power Dissipation (TC = 25°C)(2) PD 1.3 W *Continuous Forward Current ELECTRICAL / OPTICAL CHARACTERISTICS PARAMETER *Peak Emission Wavelength *Reverse Leakage Current (TA =25°C) (All measurements made under pulse conditions) TEST CONDITIONS SYMBOL MIN TYP MAX UNITS IF = 100 mA DP 935 — 955 nm 0 — ±10 — Deg. IF = 100 mA VF — — 1.7 V Emission Angle at 1/2 Power Forward Voltage 1 3 0.040 (1.02) *Soldering Temperature 3 VR = 3 V IR — — 10 µA IF = 100 mA Ie 25 — — mW/sr Rise Time 0-90% of output tr — 1.0 — µs Fall Time 100-10% of output tf — 1.0 — µs *Radiant Intensity 2001 Fairchild Semiconductor Corporation DS300278 3/12/01 1 OF 7 www.fairchildsemi.com 1N6266 GaAs INFRARED EMITTING DIODE MAXIMUM RATINGS CURVES 150 10 8 PU LS E W ID 2 TH 2 µS 10 1.0 0.8 = µS 0.6 µS 50 0.4 S 0µ 10 IF = INPUT CURRENT (mA) 4 TA = MAXIMUM ALLOWABLE AMBIENT TEMPERATURE (˚C) 6 0.2 0.1 125 100 75 100% Duty Cycle 1% Duty Cycle 25 0 100 10 1000 10,000 100,000 .01 .02 .04 .06 .08 0.1 f = FREQUENCY - HERTZ .2 .4 .6 .8 1.0 2 4 6 8 10 IF - INPUT CURRENT (mA) Fig.1 Maximum Pulse Capability Fig.2 Maximum Temperature vs. Input Current 10.0 8.0 6.0 100 .80 60 40 4.0 20 IF = FORWARD CURRENT (A) Ie = NORMALIZED RADIANT INTENSITY 10% Duty Cycle 50 10 8 6 4 2 1.0 .8 .6 .4 Normalized to: IF = 100 mA N = .01 Steradians TA = 25˚C .2 .10 .08 .06 .04 2.0 1.0 0.8 0.6 0.4 0.2 0.1 .08 .06 .04 .02 .02 .01 .01 .01 .02 .04 .06 .08 .1 .2 .4 .6 .8 1.0 2 4 0 6 8 10 IF - INPUT CURRENT (A) 2 3 4 5 6 7 8 9 10 VF - FORWARD VOLTAGE (V) Fig.3 Radiant Intensity vs. Input Current le/l www.fairchildsemi.com 1 Fig.4 Forward Voltage vs. Forward Current 2 OF 7 3/12/01 DS300278 1N6266 GaAs INFRARED EMITTING DIODE MAXIMUM RATINGS CURVES 100 80 1.0 0.8 40 RELATIVE OUTPUT IF = FORWARD CURRENT (mA) 60 20 10 8 TA = 100˚C 25˚C -55˚C 6 4 0.6 0.4 0.2 2 0 0 0.9 1.0 1.1 1.2 1.3 1.4 1.5 880 900 920 940 960 980 1000 D- WAVELENGTH - NANOMETERS Fig.5 Forward Voltage vs. Forward Current Fig.6 Spectral Output IR = NORMALIZED POWER OUTPUT VF - FORWARD VOLTAGE (V) 100 80 60 40 Normalized to: IF = 100 mA N = .01 Steradians TA = 25˚C Silicon Photodiode as Detector 20 IF = 1 A 10 8 6 4 1020 IF = 100 mA 2 1.0 .8 .6 .4 .2 IF = 10 mA .10 .08 .06 .04 .02 .01 -50 -25 0 25 50 75 100 125 150 TA - AMBIENT TEMPERATURE (˚C) Fig.7 Output vs. Temperature DS300278 3/12/01 3 OF 7 www.fairchildsemi.com 1N6266 GaAs INFRARED EMITTING DIODE INFRARED EMITTING DIODE RADIANT INTENSITY The design of an Infrared Emitting Diode (IRED)-photodetector system normally requires the designer to determine the minimum amount of infrared irradiance received by the photodetector, which then allows definition of the photodetector current. Prior to the introduction of the 1N6266, the best method of estimating the photodetector received infrared was to geometrically proportion the piecewise integration of the typical beam pattern with the specified minimum total power output of the IRED. However, due to inconsistencies of the IRED integral lenses and the beam lobes, this procedure will not provide a valid estimation. The 1N6266 now provides the designer specifications which precisely define the infrared beam along the device’s mechanical axis. The 1N6266 is a premium device selected to give a minimum radiant intensity of 25 mW/steradian into the 0.01 steradians referenced by the the device’s mechanical axis and seating plane. Radiant intensity is the IRED beam power output, within a specified solid angle, per unit solid angle. A quick review of geometry indicates that a steradian is a unit of solid angle, referenced to the center of a sphere, defined by 4 H times the ratio of the area projected by the solid angle to the area of the sphere. The solid angle is equal to the projected area divided by the squared radius. Steradians = 4 H A/4 H R2 = A/R2 = N As the projected area has a circular periphery, a geometric integration will solve to show the relationship of the Cartesian angle () of the cone, (from the center of the sphere) to the projected area. N= 2 H(1 - COS ) 2 www.fairchildsemi.com Radiant intensity provides an easy, accurate tool to calculate the infrared power received by a photodetector located on the IRED axis. As the devices are selected for beam characteristics, the calculated results are valid for worst case analysis. For many applications a simple approximation for photodetector irradiance is: H ≅ Ie/d2, in mw/cm2 where d is the distance from the IRED to the detector in cm. IRED power output, and therefore Ie, depends on IRED current. This variation (Ie/I) is documented in Figure 3, and completes the approximation: H = Ie/d2 (Ie/I). This normally gives a conservative value of irradiance. For more accurate results, the effect of precise angle viewed by the detector must be considered. This is documented in figure 8 (Ie/N) giving: H = Ie/d2 (Ie/N) in mw/cm2 For worst case designs, temperature coefficients and tolerances must be considered. The minimum output current of the detector (IL) can be determined for a given distance (d) of the detector from the IRED. IL = (S)H ≅ (S) Ie/d2 or IL = (S)H = (S) (Ie/d2) (Ie/N) (Ie/I) where S is the sensitivity of the detector in terms of output current per unit irradiance from a GaAs source. 4 OF 7 3/12/01 DS300278 1N6266 GaAs INFRARED EMITTING DIODE IRED RADIANT INTENSITY SPECIFICATION CONCEPT IRED Seating Plane SPHERE Centered on IRED Axis CL and Seating Plane Area "A" Receives Power "Pw" IRED CL d N = A/d2 = 2H(I - COS ) Steradians 2 Ie = Pw/N mW/Steradians H = Pw/A = Ie/d2 mW/cm2 MATCHING A PHOTOTRANSISTOR WITH 1N6266 Assume a system requiring a 10 mA IL at an IRED to detector spacing of 2 cm (seating plane to seating plane), with bias conditions at specification points. Given: d1 = 2 cm, IL = 10 mA min.; Ie = 25 mW/Steradian Then: H1 ≅ Ie/d12 = 25/(2)2 = 6.25 mW/cm2 Detector Evaluation: IL MIN @ ≅ H (GaAs) mW/cm2 TYPE mA L14G1 1 L14G2 0.5 Calculated IL @ d1 is: L14G1 (S) H1 = (2) 6.25 = 12.5 mA L14G2 (S) H1 = (1) 6.25 = 6.25 mA S(GaAs) mA/mw/cm2 2 1 0.5 0.5 Since the system requires an IL of 10 mA minimum the correct device to use is the L14G1. TYPICAL CHARACTERISTICS IF = NORMALIZED RADIANT INTENSITY 1.4 N= A2 r 1.2 AREA A N= 2H(I - COS ) 2 1.0 r 0.8 0.6 Normalized to: IF = 100 mA N = .01 Steradians TA = 25˚C 0.4 0.2 0.1 .001 .002 1 2 1 3 .004 .006 1 4 1 5 .01 1 7 .02 1 10 .04 .06.08 .1 1 15 1 20 Steradians - N .6 .8 1.0 1 Degrees - 45 1 60 Fig.8 Intensity and Power vs. Angle le/N DS300278 3/12/01 5 OF 7 www.fairchildsemi.com 1N6266 GaAs INFRARED EMITTING DIODE 1.4 100.0 Normalized to: IF = 100 mA D = 6 cm Distance measured from seating plane to seating plane 1.2 1.0 NORMALIZED ICE(ON) ICE(ON) = NORMALIZED COLLECTOR CURRENT MAXIMUM RATINGS CURVES 0.8 0.6 Normalized to: IF = 100 mA VCE = 5 V TA = 25˚C 0.4 1N6266 L14G1 10.0 1N6N66 L14G1 D IF = 1A, Pulsed 1.0 IF = 100 mA, DC 1.0" 0.2 0 0 -50 -25 0 25 50 75 100 125 150 TA - AMBIENT TEMPERATURE (C) 5 10 15 20 25 D - cm Fig. 9 Output vs. Ambient Temperature IRED/Phototransistor Pair www.fairchildsemi.com 0 Fig. 10 IL vs. Distance IRED/Phototransistor Pair 6 OF 7 3/12/01 DS300278 1N6266 GaAs INFRARED EMITTING DIODE DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body,or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in labeling, can be reasonably expected to result in a significant injury of the user. DS300278 3/12/01 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 7 OF 7 www.fairchildsemi.com