MOTOROLA DSP56300FM

Freescale Semiconductor
Technical Data
DSP56374
Rev. 1, 11/2004
Overview
Section
The DSP56374 is a high density CMOS device with 3.3 V inputs and outputs.
1 Features........................................ 2
Table of Contents
Page
2 Documentation.............................. 4
NOTE
This document contains information on a new product.
Specifications and information herein are subject to
change without notice.
3 Signal Groupings .......................... 4
4 Maximum Ratings ....................... 24
5 Power Requirements................... 25
Finalized specifications may be published after further characterization and device
qualifications are completed.
6 Thermal Characteristics.............. 26
7 DC Electrical Characteristics ...... 26
8 AC Electrical Characteristics....... 27
The DSP56374 supports digital audio applications requiring sound field processing,
acoustic equalization, and other digital audio algorithms. The DSP56374 uses the high
performance, single-clock-per-cycle DSP56300 core family of programmable CMOS digital
signal processors (DSPs) combined with the audio signal processing capability of the
Freescale Semiconductor, Inc. (formerly Motorola) Symphony™ DSP family, as shown in
Figure 1. Significant architectural enhancements include a barrel shifter, 24-bit addressing,
and direct memory access (DMA). The DSP56374 offers 150 million instructions per second
(MIPS) using an internal 150 MHz clock.
9 Internal Clocks ............................ 27
10 External Clock Operation .......... 29
11 Reset, Stop, Mode Select, and
Interrupt Timing ........................... 30
12 Serial Host Interface SPI Protocol
Timing.......................................... 34
13 Serial Host Interface (SHI) I2C
Protocol Timing ........................... 40
14 Programming the Serial Clock .. 42
Data Sheet Conventions
This data sheet uses the following conventions:
15 Enhanced Serial Audio Interface
Timing.......................................... 43
16 Timer Timing ............................. 48
OVERBAR
Used to indicate a signal that is active when pulled low (For
example, the RESET pin is active when low.)
17 GPIO Timing ............................. 48
“asserted”
Means that a high true (active high) signal is high or that a low true
(active low) signal is low
19 Watchdog Timer Timing ............ 52
“deasserted” Means that a high true (active high) signal is low or that a low true
(active low) signal is high
Examples:
Signal/
Symbol
Logic State
Signal State
Voltage*
PIN
True
Asserted
VIL / VOL
PIN
False
Deasserted
VIH / VOH
PIN
True
Asserted
VIH / VOH
PIN
False
Deasserted
VIL / VOL
Note: *Values for VIL, VOL, VIH, and VOH are defined by individual product specifications.
© Freescale Semiconductor, Inc., 2004. All rights reserved.
PRELIMINARY
18 JTAG Timing ............................. 50
Appendix A Package Information. 53
Appendix B IBIS Model ................. 63
Features
15*
5
3
12*
12
Memory Expansion Area
Watch
dog
Timer
Program
RAM
6k × 24
X Data
RAM
6k × 24
Y Data
RAM
6k × 24
ROM
20k × 24
ROM
4k × 24
ROM
4k × 24
Peripheral
Expansion Area
Address
Generation
Unit
Six Channel
DMA Unit
YAB
XAB
PAB
DAB
YM_EB
Triple
Timer
XM_EB
ESAI_1
Interface
PIO_EB
ESAI
Interface
PM_EB
GPIO
SHI
Interface
24-Bit
Bootstrap
ROM
DSP56300
Core
DDB
YDB
XDB
PDB
GDB
Internal
Data
Bus
Switch
Clock
Gen.
Power
Mgmt.
PLL
Program
Interrupt
Controller
XTAL
EXTAL
RESET
PINIT/NMI
Program
Decode
Controller
Program
Address
Generator
Data ALU
24 × 24+56→56-bit MAC
Two 56-bit Accumulators
56-bit Barrel Shifter
4
JTAG
OnCE
MODA/IRQA/GPIO
MODB/IRQB/GPIO
MODC/IRQC/GPIO
MODD/IRQD/GPIO
* ESAI_1 and dedicated GPIO pins are not available in the 52-pin package.
Figure 1. DSP56374 Block Diagram
1
Features
1.1
DSP56300 Modular Chassis
•
•
•
•
•
•
•
•
•
•
2
150 Million Instructions Per Second (MIPS) with a 150 MHz clock at an internal logic supply (QVDDL) of 1.25 V.
Object Code Compatible with the 56K core.
Data ALU with a 24 x 24 bit multiplier-accumulator and a 56-bit barrel shifter;16 bit arithmatic support.
Program Control with position independent code support.
Six-channel DMA controller.
Provides a wide range of frequency multiplications (1 to 255), predivider factors (1 to 31), PLL feedback multiplier (2 or
4), Output divide factor (1, 2 or 4) and a power-saving clock divider (2i: i = 0 to 7) to reduce clock noise
Internal address tracing support and OnCE for Hardware/Software debugging.
JTAG port, supporting boundary scan, compliant to IEEE 1149.1.
Very low-power CMOS design, fully static design with operating frequencies down to DC.
STOP and WAIT low-power standby modes.
PRELIMINARY
Freescale Semiconductor
Features
1.2
On-chip Memory Configuration
•
•
•
•
•
6Kx24 Bit Y-Data RAM and 4Kx24 Bit Y-Data ROM.
6Kx24 Bit X-Data RAM and 4Kx24 Bit X-Data ROM.
20Kx24 Bit Program and Bootstrap ROM including a PROM patching mechanism.
6Kx24 Bit Program RAM.
Various memory switches are available. See memory table below.
Table 1. DSP56374 Memory Switch Configurations
Bit Settings
1.3
Memory Sizes (24-bit words)
MSW1
MSW0
MS
Prog
RAM
X Data
RAM
Y Data
RAM
Prog
ROM
X Data
ROM
Y Data
ROM
X
X
0
6K
6K
6K
20K
4K
4K
0
0
1
2K
10K
6K
20K
4K
4K
0
1
1
4K
8K
6K
20K
4K
4K
1
0
1
8K
4K
6K
20K
4K
4K
1
1
1
10K
4K
4K
20K
4K
4K
Peripheral modules
•
•
•
•
•
•
1.4
Enhanced Serial Audio Interface (ESAI): up to 4 receiver pins and up to 6 transmitter pins, master or slave. I2S, Sony,
AC97, network and other programmable protocols.
Enhanced Serial Audio Interface I (ESAI_1): up to 4 receiver pins and up to 6 transmitter pins, master or slave. I2S, Sony,
AC97, network and other programmable protocols. Note: Available in the 80 pin package only
Serial Host Interface (SHI): SPI and I2C protocols, 10-word receive FIFO, support for 8, 16 and 24-bit words. Three noise
reduction filter modes.
Triple Timer module (TEC).
Most pins of unused peripherals may be programmed as GPIO pins. Up to 47 pins can be configured as GPIO on the
80 pin package and 20 pins on the 52 pin package.
Hardware Watchdog Timer
Packages
•
80-pin and 52-pin plastic LQFP packages.
Freescale Semiconductor
PRELIMINARY
3
Documentation
2
Documentation
Table 2 lists the documents that provide a complete description of the DSP56374 and are required to design properly with the
part. Documentation is available from a local Freescale Semiconductor, Inc. (formerly Motorola) distributor, semiconductor sales
office, Literature Distribution Center, or through the Freescale DSP home page on the Internet (the source for the latest
information).
Table 2. DSP56374 Documentation
Document Name
3
Description
Order Number
DSP56300 Family Manual
Detailed description of the 56300-family architecture and the
24-bit core processor and instruction set
DSP56300FM/AD
DSP56374 User’s Manual
Detailed description of memory, peripherals, and interfaces
DSP56374UM/D
DSP56374 Technical Data Sheet
Electrical and timing specifications; pin and package
descriptions
DSP56374 Product Brief
Brief description of the chip
DSP56374
DSP56374PB/D
Signal Groupings
The input and output signals of the DSP56374 are organized into functional groups, which are listed in Table 3..
The DSP56374 is operated from a 1.25 V and 3.3 V supply; however, some of the inputs can tolerate 5.0 V. A special notice for
this feature is added to the signal descriptions of those inputs.
Table 3. DSP56374 Functional Signal Groupings
Number of
Signals1
Detailed
Description
Power (VDD)
11
Table 15.
Ground (GND)
9
Table 5.
Scan Pins
1
Table 6.
Clock and PLL
3
Table 7.
Port H2
5
Table 8.
SHI
Port
H2
5
Table 9.
ESAI
Port C4
12
Table 10.
ESAI_1
Port
E5
12
Table 11.
Dedicated GPIO
Port G3
15
Table 12.
Timer
3
Table 13.
JTAG/OnCE Port
4
Table 14.
Functional Group
Interrupt and mode control
Note:
4
1.
2.
3.
4.
5.
Pins are not 5 V. tolerant unless noted.
Port H signals are the GPIO port signals which are multiplexed with the MOD and HREQ signals.
Port G signals are the dedicated GPIO port signals.
Port C signals are the GPIO port signals which are multiplexed with the ESAI signals.
Port E signals are the GPIO port signals which are multiplexed with the ESAI_1 signals.
PRELIMINARY
Freescale Semiconductor
Signal Groupings
3.1
Power
Table 4. Power Inputs
Power Name
Description
PLLA_VDD (1)
PLL Power— The voltage (3.3 V) should be well-regulated and the input should be provided with
an extremely low impedance path to the 3.3 VDD power rail. The user must provide adequate
external decoupling capacitors between PLLA_VDD and PLLA_GND. PLLA_VDD requires a
filter as shown in Figure 21 and Figure 22 below. See the DSP56374 technical data sheet for
additional details.
PLLP_VDD(1)
PLL Power— The voltage (3.3 V) should be well-regulated and the input should be provided with
an extremely low impedance path to the 3.3 VDD power rail. The user must provide adequate
external decoupling capacitors between PLLP_VDD and PLLP_GND.
PLLD_VDD (1)
PLL Power— The voltage (1.25 V) should be well-regulated and the input should be provided
with an extremely low impedance path to the 1.25 VDD power rail. The user must provide
adequate external decoupling capacitors between PLLD_VDD and PLLD_GND.
CORE_VDD (4)
Core Power—The voltage (1.25 V) should be well-regulated and the input should be provided
with an extremely low impedance path to the 1.25 VDD power rail. The user must provide
adequate external decoupling capacitors.
IO_VDD
(80-pin 4)
(52-pin 3)
3.2
SHI, ESAI, ESAI_1, WDT and Timer I/O Power —The voltage (3.3 V) should be well-regulated,
and the input should be provided with an extremely low impedance path to the 3.3 VDD power
rail. This is an isolated power for the SHI, ESAI, ESAI_1, WDT and Timer I/O. The user must
provide adequate external decoupling capacitors.
Ground
Table 5. Grounds
Ground Name
Description
PLLA_GND(1)
PLL Ground—The PLL ground should be provided with an extremely low-impedance path to
ground. This connection must be tied externally to all other chip ground connections. The user
must provide adequate external decoupling capacitors between PLLA_VDD and PLLA_GND.
PLLP_GND(1)
PLL Ground—The PLL ground should be provided with an extremely low-impedance path to
ground. This connection must be tied externally to all other chip ground connections. The user
must provide adequate external decoupling capacitors between PLLP_VDD and PLLP_GND.
PLLD_GND(1)
PLL Ground—The PLL ground should be provided with an extremely low-impedance path to
ground. This connection must be tied externally to all other chip ground connections. The user
must provide adequate external decoupling capacitors between PLLD_VDD and PLLD_GND.
CORE_GND(4)
Core Ground—The Core ground should be provided with an extremely low-impedance path to
ground. This connection must be tied externally to all other chip ground connections. The user
must provide adequate external decoupling capacitors.
IO_GND(2)
SHI, ESAI, ESAI_1, WDT and Timer I/O Ground—IO_GND is the ground for the SHI, ESAI,
ESAI_1, WDT and Timer I/O. This connection must be tied externally to all other chip ground
connections. The user must provide adequate external decoupling capacitors.
Freescale Semiconductor
PRELIMINARY
5
Signal Groupings
3.3
SCAN
Table 6. SCAN signals
3.4
Signal
Name
Type
State
during
Reset
SCAN
Input
Input
Signal Description
SCAN—Manufacturing test pin. This pin must be connected to ground.
Clock and PLL
Table 7. Clock and PLL Signals
Signal
Name
Type
State
during
Reset
EXTAL
Input
Input
XTAL
Output
PINIT/NMI
Input
Signal Description
External Clock / Crystal Input—An external clock source must be connected
to EXTAL in order to supply the clock to the internal clock generator and PLL.
Chip Driven Crystal Output—Connects the internal Crystal Oscillator output to an
external crystal. If an external clock is used, leave XTAL unconnected.
Input
PLL Initial/Nonmaskable Interrupt—During assertion of RESET, the value of
PINIT/NMI is written into the PLL Enable (PEN) bit of the PLL control
register, determining whether the PLL is enabled or disabled. After RESET
de-assertion and during normal instruction processing, the PINIT/NMI
Schmitt-trigger input is a negative-edge-triggered nonmaskable interrupt
(NMI) request internally synchronized to the internal system clock.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
3.5
Interrupt and Mode Control
The interrupt and mode control signals select the chip’s operating mode as it comes out of hardware reset. After RESET is deasserted, these inputs are hardware interrupt request lines.
Table 8. Interrupt and Mode Control
Signal Name
Type
State
during
Reset
MODA/IRQA
Input
MODA
Input
Signal Description
Mode Select A/External Interrupt Request A—MODA/IRQA is an
active-low Schmitt-trigger input, internally synchronized to the DSP
clock. MODA/IRQA selects the initial chip operating mode during
hardware reset and becomes a level-sensitive or negative-edgetriggered, maskable interrupt request input during normal instruction
processing. This pin can also be programmed as GPIO. MODA, MODB,
MODC, and MODD select one of 16 initial chip operating modes,
latched into the OMR when the RESET signal is de-asserted. If the
processor is in the stop standby state and the MODA/IRQA pin is pulled
to GND, the processor will exit the stop state.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
6
PRELIMINARY
Freescale Semiconductor
Signal Groupings
Table 8. Interrupt and Mode Control (Continued)
Signal Name
Type
PH0
Input, output,
or
disconnected
MODB/IRQB
Input
State
during
Reset
Signal Description
Port H0—When the MODA/IRQA is configured as GPIO, this signal is
individually programmable as input, output, or internally disconnected.
MODB
Input
Mode Select B/External Interrupt Request B—MODB/IRQB is an
active-low Schmitt-trigger input, internally synchronized to the DSP
clock. MODB/IRQB selects the initial chip operating mode during
hardware reset and becomes a level-sensitive or negative-edgetriggered, maskable interrupt request input during normal instruction
processing. This pin can also be programmed as GPIO. MODA, MODB,
MODC, and MODD select one of 16 initial chip operating modes,
latched into OMR when the RESET signal is de-asserted.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
PH1
Input, output,
or
disconnected
MODC/IRQC
Input
Port H1—When the MODB/IRQB is configured as GPIO, this signal is
individually programmable as input, output, or internally disconnected.
MODC
Input
Mode Select C/External Interrupt Request C—MODC/IRQC is an
active-low Schmitt-trigger input, internally synchronized to the DSP
clock. MODC/IRQC selects the initial chip operating mode during
hardware reset and becomes a level-sensitive or negative-edgetriggered, maskable interrupt request input during normal instruction
processing. This pin can also be programmed as GPIO. MODA, MODB,
MODC, and MODD select one of 16 initial chip operating modes,
latched into OMR when the RESET signal is de-asserted.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
PH2
Input, output,
or
disconnected
MODD/IRQD
Input
Port H2—When the MODC/IRQC is configured as GPIO, this signal is
individually programmable as input, output, or internally disconnected.
MODD
Input
Mode Select D/External Interrupt Request D—MODD/IRQD is an
active-low Schmitt-trigger input, internally synchronized to the DSP
clock. MODD/IRQD selects the initial chip operating mode during
hardware reset and becomes a level-sensitive or negative-edgetriggered, maskable interrupt request input during normal instruction
processing. This pin can also be programmed as GPIO. MODA, MODB,
MODC, and MODD select one of 16 initial chip operating modes,
latched into OMR when the RESET signal is de-asserted.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
PH3
Input, output,
or
disconnected
Freescale Semiconductor
Port H3—When the MODD/IRQD is configured as GPIO, this signal is
individually programmable as input, output, or internally disconnected.
PRELIMINARY
7
Signal Groupings
Table 8. Interrupt and Mode Control (Continued)
Signal Name
Type
State
during
Reset
RESET
Input
Input
Signal Description
Reset—RESET is an active-low, Schmitt-trigger input. When asserted,
the chip is placed in the Reset state and the internal phase generator is
reset. The Schmitt-trigger input allows a slowly rising input (such as a
capacitor charging) to reset the chip reliably. When the RESET signal is
de-asserted, the initial chip operating mode is latched from the MODA,
MODB, MODC, and MODD inputs. The RESET signal must be
asserted during power up. A stable EXTAL signal must be supplied
while RESET is being asserted.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
3.6
Serial Host Interface
The SHI has five I/O signals that can be configured to allow the SHI to operate in either SPI or I2C mode.
Table 9. Serial Host Interface Signals
Signal
Name
Signal Type
State during
Reset
Signal Description
SCK
Input or output
Tri-stated
SPI Serial Clock—The SCK signal is an output when the SPI is configured
as a master and a Schmitt-trigger input when the SPI is configured as a
slave. When the SPI is configured as a master, the SCK signal is derived
from the internal SHI clock generator. When the SPI is configured as a
slave, the SCK signal is an input, and the clock signal from the external
master synchronizes the data transfer. The SCK signal is ignored by the
SPI if it is defined as a slave and the slave select (SS) signal is not
asserted. In both the master and slave SPI devices, data is shifted on one
edge of the SCK signal and is sampled on the opposite edge where data is
stable. Edge polarity is determined by the SPI transfer protocol.
SCL
Input or output
I2C Serial Clock—SCL carries the clock for I2C bus transactions in the I2C
mode. SCL is a Schmitt-trigger input when configured as a slave and an
open-drain output when configured as a master. SCL should be connected
to VDD through an external pull-up resistor according to the I2C
specifications.
This signal is tri-stated during hardware, software, and individual reset.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
8
PRELIMINARY
Freescale Semiconductor
Signal Groupings
Table 9. Serial Host Interface Signals (Continued)
Signal
Name
Signal Type
State during
Reset
Signal Description
MISO
Input or output
Tri-stated
SPI Master-In-Slave-Out—When the SPI is configured as a master, MISO
is the master data input line. The MISO signal is used in conjunction with
the MOSI signal for transmitting and receiving serial data. This signal is a
Schmitt-trigger input when configured for the SPI Master mode, an output
when configured for the SPI Slave mode, and tri-stated if configured for the
SPI Slave mode when SS is de-asserted. An external pull-up resistor is not
required for SPI operation.
SDA
Input or opendrain output
I2C Data and Acknowledge—In I2C mode, SDA is a Schmitt-trigger input
when receiving and an open-drain output when transmitting. SDA should
be connected to VDD through a pull-up resistor. SDA carries the data for
I2C transactions. The data in SDA must be stable during the high period of
SCL. The data in SDA is only allowed to change when SCL is low. When
the bus is free, SDA is high. The SDA line is only allowed to change during
the time SCL is high in the case of start and stop events. A high-to-low
transition of the SDA line while SCL is high is a unique situation, and is
defined as the start event. A low-to-high transition of SDA while SCL is high
is a unique situation defined as the stop event.
This signal is tri-stated during hardware, software, and individual reset.
Thus, there is no need for an external pull-up in this state.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
MOSI
Input or output
HA0
Input
Tri-stated
SPI Master-Out-Slave-In—When the SPI is configured as a master, MOSI
is the master data output line. The MOSI signal is used in conjunction with
the MISO signal for transmitting and receiving serial data. MOSI is the
slave data input line when the SPI is configured as a slave. This signal is a
Schmitt-trigger input when configured for the SPI Slave mode.
I2C Slave Address 0—This signal uses a Schmitt-trigger input when
configured for the I2C mode. When configured for I2C slave mode, the HA0
signal is used to form the slave device address. HA0 is ignored when
configured for the I2C master mode.
This signal is tri-stated during hardware, software, and individual reset.
Thus, there is no need for an external pull-up in this state.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
SS
Input
Ignored Input SPI Slave Select—This signal is an active low Schmitt-trigger input when
configured for the SPI mode. When configured for the SPI Slave mode, this
signal is used to enable the SPI slave for transfer. When configured for the
SPI master mode, this signal should be kept de-asserted (pulled high). If it
is asserted while configured as SPI master, a bus error condition is
flagged. If SS is de-asserted, the SHI ignores SCK clocks and keeps the
MISO output signal in the high-impedance state.
HA2
Input
I2C Slave Address 2—This signal uses a Schmitt-trigger input when
configured for the I2C mode. When configured for the I2C Slave mode, the
HA2 signal is used to form the slave device address. HA2 is ignored in the
I2C master mode.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
Freescale Semiconductor
PRELIMINARY
9
Signal Groupings
Table 9. Serial Host Interface Signals (Continued)
Signal
Name
Signal Type
State during
Reset
HREQ
Input or Output
Tri-stated
Signal Description
Host Request—This signal is an active low Schmitt-trigger input when
configured for the master mode but an active low output when configured
for the slave mode.
When configured for the slave mode, HREQ is asserted to indicate that the
SHI is ready for the next data word transfer and de-asserted at the first
clock pulse of the new data word transfer. When configured for the master
mode, HREQ is an input. When asserted by the external slave device, it will
trigger the start of the data word transfer by the master. After finishing the
data word transfer, the master will await the next assertion of HREQ to
proceed to the next transfer. This pin can also be programmed as GPIO.
Port H4—When HREQ is configured as GPIO, this signal is individually
programmable as input, output, or internally disconnected.
This pin has an internal pull up resistor.
PH4
3.7
This input is 5 V tolerant.
Input, output,
or
disconnected
Enhanced Serial Audio Interface
Table 10. Enhanced Serial Audio Interface Signals
Signal Name
Signal Type
State during
Reset
HCKR
Input or output
GPIO
disconnected
PC2
Input, output, or
disconnected
Signal Description
High Frequency Clock for Receiver—When programmed
as an input, this signal provides a high frequency clock
source for the ESAI receiver as an alternate to the DSP
core clock. When programmed as an output, this signal
can serve as a high-frequency sample clock (e.g., for
external digital to analog converters [DACs]) or as an
additional system clock.
Port C2—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
10
PRELIMINARY
Freescale Semiconductor
Signal Groupings
Table 10. Enhanced Serial Audio Interface Signals (Continued)
Signal Name
Signal Type
State during
Reset
Signal Description
HCKT
Input or output
GPIO
disconnected
High Frequency Clock for Transmitter—When programmed
as an input, this signal provides a high frequency clock
source for the ESAI transmitter as an alternate to the DSP
core clock. When programmed as an output, this signal
can serve as a high frequency sample clock (e.g., for
external DACs) or as an additional system clock.
PC5
Input, output, or
disconnected
Port C5—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
FSR
Input or output
GPIO
disconnected
Frame Sync for Receiver—This is the receiver frame sync
input/output signal. In the asynchronous mode (SYN=0),
the FSR pin operates as the frame sync input or output
used by all the enabled receivers. In the synchronous
mode (SYN=1), it operates as either the serial flag 1 pin
(TEBE=0), or as the transmitter external buffer enable
control (TEBE=1, RFSD=1).
When this pin is configured as serial flag pin, its direction is
determined by the RFSD bit in the RCCR register. When
configured as the output flag OF1, this pin will reflect the
value of the OF1 bit in the SAICR register, and the data in
the OF1 bit will show up at the pin synchronized to the
frame sync in normal mode or the slot in network mode.
When configured as the input flag IF1, the data value at
the pin will be stored in the IF1 bit in the SAISR register,
synchronized by the frame sync in normal mode or the slot
in network mode.
PC1
Input, output, or
disconnected
Port C1—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
Freescale Semiconductor
PRELIMINARY
11
Signal Groupings
Table 10. Enhanced Serial Audio Interface Signals (Continued)
Signal Name
Signal Type
State during
Reset
Signal Description
FST
Input or output
GPIO
disconnected
Frame Sync for Transmitter—This is the transmitter frame
sync input/output signal. For synchronous mode, this
signal is the frame sync for both transmitters and
receivers. For asynchronous mode, FST is the frame sync
for the transmitters only. The direction is determined by the
transmitter frame sync direction (TFSD) bit in the ESAI
transmit clock control register (TCCR).
PC4
Input, output, or
disconnected
Port C4—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SCKR
Input or output
GPIO
disconnected
Receiver Serial Clock—SCKR provides the receiver serial
bit clock for the ESAI. The SCKR operates as a clock input
or output used by all the enabled receivers in the
asynchronous mode (SYN=0), or as serial flag 0 pin in the
synchronous mode (SYN=1).
When this pin is configured as serial flag pin, its direction is
determined by the RCKD bit in the RCCR register. When
configured as the output flag OF0, this pin will reflect the
value of the OF0 bit in the SAICR register, and the data in
the OF0 bit will show up at the pin synchronized to the
frame sync in normal mode or the slot in network mode.
When configured as the input flag IF0, the data value at
the pin will be stored in the IF0 bit in the SAISR register,
synchronized by the frame sync in normal mode or the slot
in network mode.
PC0
Input, output, or
disconnected
Port C0—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SCKT
Input or output
PC3
Input, output, or
disconnected
GPIO
disconnected
Transmitter Serial Clock—This signal provides the serial
bit rate clock for the ESAI. SCKT is a clock input or output
used by all enabled transmitters and receivers in
synchronous mode, or by all enabled transmitters in
asynchronous mode.
Port C3—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
12
PRELIMINARY
Freescale Semiconductor
Signal Groupings
Table 10. Enhanced Serial Audio Interface Signals (Continued)
Signal Name
Signal Type
State during
Reset
SDO5
Output
GPIO
disconnected
SDI0
Input
Serial Data Input 0—When programmed as a receiver,
SDI0 is used to receive serial data into the RX0 serial
receive shift register.
PC6
Input, output, or
disconnected
Port C6—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
Signal Description
Serial Data Output 5—When programmed as a
transmitter, SDO5 is used to transmit data from the TX5
serial transmit shift register.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO4
Output
GPIO
disconnected
Serial Data Output 4—When programmed as a
transmitter, SDO4 is used to transmit data from the TX4
serial transmit shift register.
SDI1
Input
Serial Data Input 1—When programmed as a receiver,
SDI1 is used to receive serial data into the RX1 serial
receive shift register.
PC7
Input, output, or
disconnected
Port C7—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO3
Output
GPIO
disconnected
Serial Data Output 3—When programmed as a
transmitter, SDO3 is used to transmit data from the TX3
serial transmit shift register.
SDI2
Input
Serial Data Input 2—When programmed as a receiver,
SDI2 is used to receive serial data into the RX2 serial
receive shift register.
PC8
Input, output, or
disconnected
Port C8—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
Freescale Semiconductor
PRELIMINARY
13
Signal Groupings
Table 10. Enhanced Serial Audio Interface Signals (Continued)
Signal Name
Signal Type
State during
Reset
SDO2
Output
GPIO
disconnected
SDI3
Input
Serial Data Input 3—When programmed as a receiver,
SDI3 is used to receive serial data into the RX3 serial
receive shift register.
PC9
Input, output, or
disconnected
Port C9—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
Signal Description
Serial Data Output 2—When programmed as a
transmitter, SDO2 is used to transmit data from the TX2
serial transmit shift register
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO1
Output
PC10
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 1—SDO1 is used to transmit data from
the TX1 serial transmit shift register.
Port C10—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO0
Output
PC11
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 0—SDO0 is used to transmit data from
the TX0 serial transmit shift register.
Port C11—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
14
PRELIMINARY
Freescale Semiconductor
Signal Groupings
3.8
Enhanced Serial Audio Interface_1
Table 11. Enhanced Serial Audio Interface_1 Signals
Signal
Name
Signal Type
HCKR_1
Input or output
PE2
Input, output, or
disconnected
State during Signal Description
Reset
GPIO
disconnected
High Frequency Clock for Receiver—When programmed
as an input, this signal provides a high frequency clock
source for the ESAI_1 receiver as an alternate to the DSP
core clock. When programmed as an output, this signal can
serve as a high-frequency sample clock (e.g., for external
digital to analog converters [DACs]) or as an additional
system clock.
Port E2—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
HCKT_1
Input or output
PE5
Input, output, or
disconnected
GPIO
disconnected
High Frequency Clock for Transmitter—When programmed
as an input, this signal provides a high frequency clock
source for the ESAI_1 transmitter as an alternate to the
DSP core clock. When programmed as an output, this
signal can serve as a high frequency sample clock (e.g., for
external DACs) or as an additional system clock.
Port E5—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
Freescale Semiconductor
PRELIMINARY
15
Signal Groupings
Table 11. Enhanced Serial Audio Interface_1 Signals (Continued)
Signal
Name
Signal Type
FSR_1
Input or output
State during Signal Description
Reset
GPIO
disconnected
Frame Sync for Receiver_1—This is the receiver frame
sync input/output signal. In the asynchronous mode
(SYN=0), the FSR_1 pin operates as the frame sync input
or output used by all the enabled receivers. In the
synchronous mode (SYN=1), it operates as either the
serial flag 1 pin (TEBE=0), or as the transmitter external
buffer enable control (TEBE=1, RFSD=1).
When this pin is configured as serial flag pin, its direction is
determined by the RFSD bit in the RCCR_1 register. When
configured as the output flag OF1, this pin will reflect the
value of the OF1 bit in the SAICR_1 register, and the data
in the OF1 bit will show up at the pin synchronized to the
frame sync in normal mode or the slot in network mode.
When configured as the input flag IF1, the data value at the
pin will be stored in the IF1 bit in the SAISR_1 register,
synchronized by the frame sync in normal mode or the slot
in network mode.
PE1
Input, output, or
disconnected
Port E1—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
FST_1
Input or output
PE4
Input, output, or
disconnected
GPIO
disconnected
Frame Sync for Transmitter_1—This is the transmitter
frame sync input/output signal. For synchronous mode, this
signal is the frame sync for both transmitters and receivers.
For asynchronous mode, FST_1 is the frame sync for the
transmitters only. The direction is determined by the
transmitter frame sync direction (TFSD) bit in the ESAI_1
transmit clock control register (TCCR_1).
Port E4—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
16
PRELIMINARY
Freescale Semiconductor
Signal Groupings
Table 11. Enhanced Serial Audio Interface_1 Signals (Continued)
Signal
Name
Signal Type
SCKR_1
Input or output
State during Signal Description
Reset
GPIO
disconnected
Receiver Serial Clock_1—SCKR_1 provides the receiver
serial bit clock for the ESAI_1. The SCKR_1 operates as a
clock input or output used by all the enabled receivers in
the asynchronous mode (SYN=0), or as serial flag 0 pin in
the synchronous mode (SYN=1).
When this pin is configured as serial flag pin, its direction is
determined by the RCKD bit in the RCCR_1 register. When
configured as the output flag OF0, this pin will reflect the
value of the OF0 bit in the SAICR_1 register, and the data
in the OF0 bit will show up at the pin synchronized to the
frame sync in normal mode or the slot in network mode.
When configured as the input flag IF0, the data value at the
pin will be stored in the IF0 bit in the SAISR_1 register,
synchronized by the frame sync in normal mode or the slot
in network mode.
PE0
Input, output, or
disconnected
Port E0—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
SCKT_1
Input or output
PE3
Input, output, or
disconnected
GPIO
disconnected
Transmitter Serial Clock_1—This signal provides the serial
bit rate clock for the ESAI_1. SCKT_1 is a clock input or
output used by all enabled transmitters and receivers in
synchronous mode, or by all enabled transmitters in
asynchronous mode.
Port E3—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
Freescale Semiconductor
PRELIMINARY
17
Signal Groupings
Table 11. Enhanced Serial Audio Interface_1 Signals (Continued)
Signal
Name
Signal Type
SDO5_1
Output
SDI0_1
Input
PE6
Input, output, or
disconnected
State during Signal Description
Reset
GPIO
disconnected
Serial Data Output 5_1—When programmed as a
transmitter, SDO5_1 is used to transmit data from the TX5
serial transmit shift register.
Serial Data Input 0_1—When programmed as a receiver,
SDI0_1 is used to receive serial data into the RX0 serial
receive shift register.
Port E6—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
SDO4_1
Output
SDI1_1
Input
PE7
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 4_1—When programmed as a
transmitter, SDO4_1 is used to transmit data from the TX4
serial transmit shift register.
Serial Data Input 1_1—When programmed as a receiver,
SDI1_1 is used to receive serial data into the RX1 serial
receive shift register.
Port E7—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO3_1
Output
SDI2_1
Input
PE8
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 3—When programmed as a
transmitter, SDO3_1 is used to transmit data from the TX3
serial transmit shift register.
Serial Data Input 2—When programmed as a receiver,
SDI2_1 is used to receive serial data into the RX2 serial
receive shift register.
Port E8—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
18
PRELIMINARY
Freescale Semiconductor
Signal Groupings
Table 11. Enhanced Serial Audio Interface_1 Signals (Continued)
State during Signal Description
Reset
Signal
Name
Signal Type
SDO2_1
Output
SDI3_1
Input
Serial Data Input 3—When programmed as a receiver,
SDI3_1 is used to receive serial data into the RX3 serial
receive shift register.
PE9
Input, output, or
disconnected
Port E9—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
GPIO
disconnected
Serial Data Output 2—When programmed as a transmitter,
SDO2_1 is used to transmit data from the TX2 serial
transmit shift register.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO1_1
Output
GPIO
disconnected
PE10
Input, output, or
disconnected
Serial Data Output 1—SDO1_1 is used to transmit data
from the TX1 serial transmit shift register.
Port E10—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO0_1
Output
GPIO
disconnected
PE11
Input, output, or
disconnected
Serial Data Output 0—SDO0_1 is used to transmit data
from the TX0 serial transmit shift register.
Port E11—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
3.9
Dedicated GPIO - Port G
Table 12. Dedicated GPIO - Port G Signals
Signal
Name
PG0
Type
State During
Reset
Input,
GPIO
disconnected
output, or
disconnected
Signal Description
Port G0—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
Freescale Semiconductor
PRELIMINARY
19
Signal Groupings
Table 12. Dedicated GPIO - Port G Signals (Continued)
Signal
Name
PG1
Type
State During
Reset
Input,
GPIO
disconnected
output, or
disconnected
Signal Description
Port G1—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG2
Input,
output, or
disconnected
GPIO
disconnected
Port G2—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG3
Input,
output, or
disconnected
GPIO
disconnected
Port G3—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG4
Input,
output, or
disconnected
GPIO
disconnected
Port G4—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG5
Input,
output, or
disconnected
GPIO
disconnected
Port G5—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG6
Input,
output, or
disconnected
GPIO
disconnected
Port G6—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG7
Input,
output, or
disconnected
GPIO
disconnected
Port G7—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG8
Input,
output, or
disconnected
GPIO
disconnected
Port G8—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
20
PRELIMINARY
Freescale Semiconductor
Signal Groupings
Table 12. Dedicated GPIO - Port G Signals (Continued)
Signal
Name
PG9
Type
State During
Reset
Input,
GPIO
disconnected
output, or
disconnected
Signal Description
Port G9—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG10
Input,
output, or
disconnected
GPIO
disconnected
Port G10—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG11
Input,
output, or
disconnected
GPIO
disconnected
Port G11—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG12
Input,
output, or
disconnected
GPIO
disconnected
Port G12—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG13
Input,
output, or
disconnected
GPIO
disconnected
Port G13—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG14
Input,
output, or
disconnected
GPIO
disconnected
Port G14—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
Freescale Semiconductor
PRELIMINARY
21
Signal Groupings
3.10
Timer
Table 13. Timer Signal
Signal
Name
Type
TIO0
Input or
Output
State
during
Reset
Signal Description
GPIO Input Timer 0 Schmitt-Trigger Input/Output—When timer 0 functions as an
external event counter or in measurement mode, TIO0 is used as input.
When timer 0 functions in watchdog, timer, or pulse modulation mode,
TIO0 is used as output.
The default mode after reset is GPIO input. This can be changed to
output or configured as a timer input/output through the timer 0
control/status register (TCSR0). If TIO0 is not being used, it is
recommended to either define it as GPIO output immediately at the
beginning of operation or leave it defined as GPIO input.
Internal Pull down resistor.
This input is 5 V tolerant
TIO1
Input or
Output
Watchdog
Timer
Output
Timer 1 Schmitt-Trigger Input/Output—When timer 1 functions as an
external event counter or in measurement mode, TIO1 is used as input.
When timer 1 functions in watchdog, timer, or pulse modulation mode,
TIO1 is used as output.
The default mode after reset is GPIO input. This can be changed to
output or configured as a timer input/output through the timer
1control/status register (TCSR1). If TIO1 is not being used, it is
recommended to either define it as GPIO output immediately at the
beginning of operation or leave it defined as GPIO input.
WDT
Output
WDT—When this pin is configured as a hardware watchdog timer pin,
this signal is asserted low when the hardware watchdog timer counts
down to zero.
Internal Pull down resistor.
This input is 5 V tolerant
TIO2
Input or
Output
PLOCK
Output
Timer 2 Schmitt-Trigger Input/Output—When timer 2 functions as an
external event counter or in measurement mode, TIO2 is used as input.
When timer 2 functions in watchdog, timer, or pulse modulation mode,
TIO2 is used as output.
The default mode after reset is GPIO input. This can be changed to
output or configured as a timer input/output through the timer
control/status register (TCSR2). If TIO2 is not being used, it is
recommended to either define it as GPIO output immediately at the
beginning of operation or leave it defined as GPIO input .
22
PRELIMINARY
Freescale Semiconductor
Signal Groupings
Table 13. Timer Signal (Continued)
Signal
Name
Type
PLOCK
Output
State
during
Reset
Signal Description
PLOCK—When this pin is configured as a PLL lock pin, this signal is
asserted high when the on-chip PLL enabled and locked and deasserted when the PLL enabled and unlocked. This pin is also
asserted high when the PLL is disabled.
Internal Pull down resistor.
This input is 5 V tolerant
3.11
JTAG/OnCE Interface
Table 14. JTAG/OnCE Interface
Signal
Name
Signal
Type
State
during
Reset
TCK
Input
Input
Signal Description
Test Clock—TCK is a test clock input signal used to synchronize the JTAG
test logic.
Internal Pull up resistor.
This input is 5 V tolerant.
TDI
Input
Input
Test Data Input—TDI is a test data serial input signal used for test
instructions and data. TDI is sampled on the rising edge of TCK.
Internal Pull up resistor.
This input is 5 V tolerant.
TDO
Output
Tri-stated
TMS
Input
Input
Test Data Output—TDO is a test data serial output signal used for test
instructions and data. TDO is tri-statable and is actively driven in the shift-IR
and shift-DR controller states. TDO changes on the falling edge of TCK.
Test Mode Select—TMS is an input signal used to sequence the test
controller’s state machine. TMS is sampled on the rising edge of TCK.
Internal Pull up resistor.
This input is 5 V tolerant.
Freescale Semiconductor
PRELIMINARY
23
Maximum Ratings
4
Maximum Ratings
Caution
This device contains circuitry protecting against damage due
to high static voltage or electrical fields. However, normal
precautions should be taken to avoid exceeding maximum
voltage ratings. Reliability of operation is enhanced if unused
inputs are pulled to an appropriate logic voltage level (e.g.,
either GND or VDD). The suggested value for a pullup or
pulldown resistor is 10 kΩ.
NOTE
In the calculation of timing requirements, adding a maximum value of one specification to a
minimum value of another specification does not yield a reasonable sum. A maximum
specification is calculated using a worst case variation of process parameter values in one
direction. The minimum specification is calculated using the worst case for the same
parameters in the opposite direction. Therefore, a “maximum” value for a specification will
never occur in the same device that has a “minimum” value for another specification; adding
a maximum to a minimum represents a condition that can never exist.
Table 15. Maximum Ratings
Rating1
Supply Voltage
Unit
−0.3 to + 1.6
V
VPLLP_VDD,
VIO_VDD,
VPLLA_VDD,
−0.3 to + 4.0
V
Tr
10
ms
VIN
GND − 0.3 to 6V
V
I
12
mA
ISCK
16
mA
IJTAG
24
ma
TJ
80 LQFP = 90
°C
VCORE_VDD,
VPLLD_VDD
Maximum CORE_VDD power supply ramp time4
All “5.0V tolerant” input voltages
Current drain per pin excluding VDD and GND(Except
for pads listed below)
SCK_SCL
TDO
Operating temperature
Value1, 2
Symbol
range3
52 LQFP = 95
Storage temperature
TSTG
ESD protected voltage (Human Body Model)
ESD protected voltage (Machine Model)
Note:
24
−55 to +125
°C
1250
V
75
V
1. GND = 0 V, TJ = 0°C to 95°C (52 LQFP) / 0°C to 90°C (80 LQFP), CL = 50pF
2. Absolute maximum ratings are stress ratings only, and functional operation at the maximum is not guaranteed. Stress
beyond the maximum rating may affect device reliability or cause permanent damage to the device.
3. Operating temperature qualified for consumer applications. TJ = TA + θJA x Power.
4. If the power supply ramp to full supply time is longer than 10 ms, the POR circuitry will not operate correctly, causing
erroneous operation.
PRELIMINARY
Freescale Semiconductor
Power Requirements
5
Power Requirements
To prevent high current conditions due to possible improper sequencing of the power supplies, the connection shown below is
recommended to be made between the DSP56374 IO_VDD and Core_VDD power pins.
IO_VDD
External
Schottky
Diode
Core_VDD
To prevent a high current condition upon power up, the IO_VDD must be applied ahead of the Core_VDD as shown below if the
external Schottky is not used.
Core_VDD
IO_VDD
For correct operation of the internal power on reset logic, the Core_VDD ramp rate (Tr) to full supply must be less than 10 ms.
This is shown below.
Tr
1.25V
0V
Core_VDD
Freescale Semiconductor
PRELIMINARY
25
Thermal Characteristics
6
Thermal Characteristics
Table 16. Thermal Characteristics
Characteristic
Natural Convection, Junction-to-ambient thermal
resistance1,2
Junction-to-case thermal
Symbol
LQFP Values
Unit
RθJA or θJA
68 (52 LQFP)
°C/W
50 (80 LQFP)
resistance3
RθJC or θJC
17 (52 LQFP)
°C/W
11 (80 LQFP)
Note:
7
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site
(board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board
thermal resistance.
2. Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board horizontal.
3. Thermal resistance between the die and the case top surface as measured by the cold plate method
(MIL SPEC-883 Method 1012.1).
DC Electrical Characteristics
Table 17. DC Electrical Characteristics
Characteristics
Supply voltages
Symbol
Min
Typ
Max
Unit
VDD
1.2
1.25
1.3
V
VDDIO
3.14
3.3
3.46
V
VIH
2.0
—
VIO_VDD+2V
• Core (Core_VDD)
• PLL (PLLD_VDD)
Supply voltages
• VIO_VDD
• PLL (PLLP_VDD)
• PLL (PLLA_VDD)
Input high voltage
• All pins
V
Note: All 3.3 volt supplies must rise prior to the rise of the 1.25 volt supplies to avoid a high current condition and possible system
damage.
Input low voltage
• All pins
26
VIL
–0.3
—
0.8
V
Input leakage current
IIN
—
—
± 84
µA
Clock pin Input Capacitance (EXTAL)
CIN
High impedance (off-state) input current (@ 3.46V)
ITSI
–10
—
84
µA
Output high voltage
IOH = -5 mA.
XTAL Pin IOH = -10mA
VOH
2.4
—
—
V
Output low voltage
IOH = 5 mA.
XTAL Pin IOH = 10mA
VOL
—
—
0.4
V
PRELIMINARY
4.7
pF
Freescale Semiconductor
AC Electrical Characteristics
Table 17. DC Electrical Characteristics (Continued)
Characteristics
Symbol
Min
Typ
Max
Unit
• In Normal mode
ICCI
—
65
100
mA
• In Wait mode
ICCW
—
16
40
mA
ICCS
—
1.2
15
mA
• In Normal mode
ICCI
—
35
60
mA
• In Wait mode
ICCW
—
36
50
mA
• In Stop mode2
ICCS
—
1.2
20
uA
CIN
—
—
10
pF
Internal supply current1 (core only) at internal clock
of 150MHz
2
• In Stop mode
Supply current1 (I/O only) at internal clock of 150MHz
Input capacitance
Note:
8
1. The Current Consumption section provides a formula to compute the estimated current requirements in Normal mode. In order
to obtain these results, all inputs must be terminated (i.e., not allowed to float). Measurements are based on synthetic intensive
DSP benchmarks. The power consumption numbers in this specification are 90% of the measured results of this benchmark.
This reflects typical DSP applications. Typical internal supply current is measured with VCORE_VDD = 1.25V, VDD_IO = 3.3V at
TJ = 25°C. Maximum internal supply current is measured with VCORE_VDD = 1.30V, VIO_VDD) = 3.46V at TJ = 115°C.
2. In order to obtain these results, all inputs, which are not disconnected at Stop mode, must be terminated (i.e., not allowed to
float).
AC Electrical Characteristics
The timing waveforms shown in the AC electrical characteristics section are tested with a VIL maximum of 0.8V and a VIH
minimum of 2.0V for all pins. AC timing specifications, which are referenced to a device input signal, are measured in production
with respect to the 50% point of the respective input signal’s transition. DSP56374 output levels are measured with the production
test machine VOL and VOH reference levels set at 1.0V and 1.8V, respectively.
9
Internal Clocks
Table 18. INTERNAL CLOCKS2
No.
Characteristics
Symbol
Min
Typ
Max
Unit
5
—
20
MHz
Condition
1
Comparison Frequency
Fref
2
Input Clock Frequency
FIN
3
Output clock Frequency (with
PLL enabled[1]
FOUT
75
(Ef × MF x FM)/
(PDF × DF x OD)
150
MHz
FOUT=FVCO/NO where
NO is output divider value
4
Output clock Frequency (with
PLL disabled[1]
FOUT
—
Ef
150
MHz
—
5
Duty Cycle
—
40
50
60
%
Freescale Semiconductor
Fref*NR
PRELIMINARY
Fref = FIN/NR
NR is input divider value
FVCO=300MHz~600MHz
27
Internal Clocks
Table 18. INTERNAL CLOCKS2 (Continued)
No.
Note:
1.
2.
28
Characteristics
Symbol
Min
Typ
Max
Unit
Condition
DF = Division Factor
Ef = External frequency
MF = Multiplication Factor
PDF = Predivision Factor
FM= Frequency Multiplier
OD = Output Divider
For details of internal clock
operation, see Chapter 5
of Users Guide.
PRELIMINARY
Freescale Semiconductor
External Clock Operation
10
External Clock Operation
The DSP56374 system clock is derived from the on-chip oscillator or is externally supplied. To use the on-chip oscillator, connect
a crystal and associated resistor/capacitor components to EXTAL and XTAL; an example is shown below.
Suggested component values:
fosc
= 24.576 MHz
R = 1 M ±10%
C (EXTAL)= 18 pF
C (XTAL) = 47 pF
Calculations are for a 12 - 49 MHz crystal with the following parameters:
• shunt capacitance (C0) of 10 pF - 12 pF
• series resistance 40 Ohm
• drive level of 10 µW
If the DSP56374 system clock is an externally supplied square wave voltage source, it is connected to EXTAL (Figure 2). When
the external square wave source connects to EXTAL, the XTAL pin is not used.
VIH
Midpoint
EXTAL
VIL
ETH
ETL
6
7
8
Note:
ETC
The midpoint is 0.5 (VIH + VIL).
Figure 2. External Clock Timing
Table 19. Clock Operation
No.
6
Characteristics
EXTAL input high 1
Symbol
Min
Max
Units
Eth
3.33
50
ns
Etl
3.33
50
ns
Etc
6.67
inf
ns
50
200
(40% to 60% duty cycle)
7
EXTAL input low1
(40% to 60% duty cycle)
8
EXTAL cycle time
• With PLL disabled
• With PLL enabled
Freescale Semiconductor
PRELIMINARY
29
Reset, Stop, Mode Select, and Interrupt Timing
Table 19. Clock Operation (Continued)
No.
9
Characteristics
Symbol
Instruction cycle time= ICYC = TC
• With PLL disabled
• With PLL enabled
Note:
11
Min
Max
Units
6.67
inf
ns
6.67
13.33
4
Icyc
1. Measured at 50% of the input transition.
2. The indicated duty cycle is for the specified maximum frequency for which a part is
rated. The minimum clock high or low time required for correct operation, however,
remains the same at lower operating frequencies; therefore, when a lower clock
frequency is used, the signal symmetry may vary from the specified duty cycle as long
as the minimum high time and low time requirements are met.
Reset, Stop, Mode Select, and Interrupt Timing
Table 20. Reset, Stop, Mode Select, and Interrupt Timing
No.
Characteristics
10
Delay from RESET assertion to all pins at reset
value3
11
Required RESET duration4
• Power on, external clock generator, PLL
disabled
• Power on, external clock generator, PLL
enabled
13
Min
Max
Unit
—
—
11
ns
2 xTC
13.4
—
ns
2 x TC
13.4
—
ns
2× TC
13.4
—
ns
(2xTC)+TLOCK
5.0
—
ms
Syn reset deassert delay time
• Minimum
• Maximum (PLL enabled)
30
Expression
14
Mode select setup time
10.0
—
ns
15
Mode select hold time
10.0
—
ns
16
Minimum edge-triggered interrupt request assertion
width
2 xTC
13.4
—
ns
17
Minimum edge-triggered interrupt request
deassertion width
2 xTC
13.4
—
ns
18
Delay from interrupt trigger to interrupt code
execution
10 × TC + 5
72
—
ns
PRELIMINARY
Freescale Semiconductor
Reset, Stop, Mode Select, and Interrupt Timing
Table 20. Reset, Stop, Mode Select, and Interrupt Timing (Continued)
No.
Characteristics
Expression
Min
Max
Unit
19
Duration of level sensitive IRQA assertion to ensure
interrupt service (when exiting Stop)1, 2, 3
9+(128× TC)
854
—
µs
• PLL is active during Stop and Stop delay is not
enabled
(OMR Bit 6 = 1)
25× TC
165
—
ns
• PLL is not active during Stop and Stop delay is
enabled (OMR Bit 6 = 0)
9+(128xTC) + TLOCK
5.7
ms
• PLL is not active during Stop and Stop delay is
not enabled (OMR Bit 6 = 1)
(25 x TC) + TLOCK
5
ms
• PLL is active during Stop and Stop delay is
enabled
(OMR Bit 6 = 0)
20
21
22
Note:
• Delay from IRQA, IRQB, IRQC, IRQD, NMI
assertion to general-purpose transfer output
valid caused by first interrupt instruction
execution1
10 x TC + 3.0
69.0
ns
Interrupt Requests Rate1
• ESAI, ESAI_1, SHI, Timer
12 x TC
—
80.0
ns
• DMA
8 x TC
—
53.0
ns
• IRQ, NMI (edge trigger)
8 x TC
—
53.0
ns
• IRQ (level trigger)
12 x TC
—
80.0
ns
• Data read from ESAI, ESAI_1, SHI
6 x TC
—
40.0
ns
• Data write to ESAI, ESAI_1, SHI
7 x TC
—
46.7
ns
• Timer
2 x TC
—
13.4
ns
• IRQ, NMI (edge trigger)
3 x TC
—
20.0
ns
DMA Requests Rate
1. When using fast interrupts and IRQA, IRQB, IRQC, and IRQD are defined as level-sensitive, timings 19 through 21 apply
to prevent multiple interrupt service. To avoid these timing restrictions, the Edge-triggered mode is recommended when
using fast interrupts. Long interrupts are recommended when using Level-sensitive mode.
2. For PLL disable, using external clock (PCTL Bit 16 = 1), no stabilization delay is required and recovery time will be
defined by the OMR Bit 6 settings.
For PLL enable, (if bet 12 of the PCTL register is 0), the PLL is shutdown during Stop. Recovering from Stop requires the
PLL to get locked. The PLL lock procedure duration, PLL Lock Cycles (PLC), may be in the range of 0.5 ms.
3. Periodically sampled and not 100% tested.
4. RESET duration is measured during the time in which RESET is asserted, VDD is valid, and the EXTAL input is active
and valid. When the VDD is valid, but the other “required RESET duration” conditions (as specified above) have not been
yet met, the device circuitry will be in an uninitialized state that can result in significant power consumption and heat-up.
Designs should minimize this state to the shortest possible duration.
Freescale Semiconductor
PRELIMINARY
31
Reset, Stop, Mode Select, and Interrupt Timing
VIH
RESET
11
13
10
All Pins
Reset Value
Figure 3. Reset Timing
IRQA, IRQB,
IRQC, IRQD,
NMI
19
18
a) First Interrupt Instruction Execution
General
Purpose
I/O
20
IRQA, IRQB,
IRQC, IRQD,
NMI
b) General Purpose I/O
Figure 4. External Fast Interrupt Timing
IRQA, IRQB,
IRQC, IRQD,
NMI
16
IRQA, IRQB,
IRQC, IRQD,
NMI
17
Figure 5. External Interrupt Timing (Negative Edge-Triggered)
32
PRELIMINARY
Freescale Semiconductor
Reset, Stop, Mode Select, and Interrupt Timing
VIH
RESET
14
15
MODA, MODB,
MODC, MODD,
PINIT
VIH
VIH
VIL
VIL
IRQA, IRQB,
IRQC,IRQD,
NMI
Figure 6. Recovery from Stop State Using IRQA Interrupt Service
Freescale Semiconductor
PRELIMINARY
33
Serial Host Interface SPI Protocol Timing
12
Serial Host Interface SPI Protocol Timing
Table 21. Serial Host Interface SPI Protocol Timing
No.
Characteristics1,3,4
Mode
Filter Mode
Min
Max
Unit
23
Minimum serial clock cycle = tSPICC(min)
Master
Bypassed
76.0
—
ns
Very Narrow
76.0
—
ns
Narrow
200.0
—
ns
Wide
400.0
—
ns
Bypassed
—
0
ns
Very Narrow
—
10
ns
Narrow
—
50
ns
Wide
—
100
ns
Bypassed
38.0
—
ns
Very Narrow
38.0
—
ns
Narrow
100.0
—
ns
Wide
200.0
—
ns
Bypassed
33.0
—
ns
Very Narrow
33.0
—
ns
Narrow
100.0
—
ns
Wide
200.0
—
ns
Bypassed
38.0
—
ns
Very Narrow
38.0
—
ns
Narrow
100.0
—
ns
Wide
200.0
—
ns
Bypassed
33.0
—
ns
Very Narrow
33.0
—
ns
Narrow
100.0
—
ns
Wide
200.0
—
ns
Master
—
—
—
ns
Slave
—
—
5
ns
XX
24
Tolerable Spike width on data or clock in.
Serial clock high period
—
Master
Slave
25
Serial clock low period
Master
Slave
26
34
Serial clock rise/fall time
PRELIMINARY
Freescale Semiconductor
Serial Host Interface SPI Protocol Timing
Table 21. Serial Host Interface SPI Protocol Timing (Continued)
No.
Characteristics1,3,4
Mode
Filter Mode
Min
Max
Unit
27
SS assertion to first SCK edge
Slave
Bypassed
38.4
—
ns
Very Narrow
28.4
—
ns
Narrow
0
—
ns
Wide
0
—
ns
Bypassed
10
—
ns
Very Narrow
0
—
ns
Narrow
0
—
ns
Wide
0
—
ns
Bypassed
12
—
ns
Very Narrow
22
—
ns
Narrow
100
—
ns
Wide
200
—
ns
Bypassed
0
—
ns
Very Narrow
0
—
ns
Narrow
0
—
ns
Wide
0
—
ns
Bypassed
23.2
—
ns
Very Narrow
43.2
—
ns
Narrow
73.2
—
ns
Wide
100.0
—
ns
CPHA = 0
CPHA = 1
28
29
30
Slave
Last SCK edge to SS not asserted
Slave
Data input valid to SCK edge (data input
set-up time)
SCK last sampling edge to data input not
valid
Master
/Slave
Master
/Slave
31
SS assertion to data out active
Slave
—
5
—
ns
32
SS deassertion to data high impedance2
Slave
—
—
9
ns
33
SCK edge to data out valid
(data out delay time)
Master
/Slave
Bypassed
—
210
ns
Very Narrow
—
270
ns
Narrow
—
376
ns
Wide
—
521
ns
Bypassed
5
—
ns
Very Narrow
15
—
ns
Narrow
55
—
ns
Wide
105
—
ns
—
—
15.0
ns
34
35
SCK edge to data out not valid
(data out hold time)
SS assertion to data out valid
(CPHA = 0)
Freescale Semiconductor
Master
/Slave
Slave
PRELIMINARY
35
Serial Host Interface SPI Protocol Timing
Table 21. Serial Host Interface SPI Protocol Timing (Continued)
No.
Characteristics1,3,4
Mode
Filter Mode
Min
Max
Unit
36
First SCK sampling edge to HREQ output
deassertion
Slave
Bypassed
50
—
ns
Very Narrow
60
—
ns
Narrow
100
—
ns
Wide
150
—
ns
Bypassed
57.0
—
ns
Very Narrow
67.0
—
ns
Narrow
107.0
—
ns
Wide
157.0
—
ns
37
Slave
38
SS deassertion to HREQ output not
deasserted (CPHA = 0)
Slave
—
50.0
—
ns
39
SS deassertion pulse width (CPHA = 0)
Slave
—
12.7
—
ns
40
HREQ in assertion to first SCK edge
Master
—
63.0
—
ns
41
HREQ in deassertion to last SCK
sampling edge (HREQ in set-up time)
(CPHA = 1)
Master
—
0
—
ns
42
First SCK edge to HREQ in not asserted
(HREQ in hold time)
Master
—
0
—
ns
43
HREQ assertion width
Master
—
20
—
ns
Note:
36
Last SCK sampling edge to HREQ output
not deasserted (CPHA = 1)
1.
2.
3.
4.
VCORE_VDD = 1.2 5 ± 0.05 V; TJ = 0°C to 95°C (52 LQFP) / 0°C to 90°C (80 LQFP), CL = 50 pF
Periodically sampled, not 100% tested
All times assume noise free inputs.
All times assume internal clock frequency of 150 MHz.
PRELIMINARY
Freescale Semiconductor
Serial Host Interface SPI Protocol Timing
SS
(Input)
25
23
24
26
26
SCK (CPOL = 0)
(Output)
24
23
26
25
26
SCK (CPOL = 1)
(Output)
29
30
MISO
(Input)
MSB
Valid
LSB
Valid
34
33
MOSI
(Output)
MSB
40
30
29
LSB
42
HREQ
(Input)
43
Figure 7. SPI Master Timing (CPHA = 0)
Freescale Semiconductor
PRELIMINARY
37
Serial Host Interface SPI Protocol Timing
SS
(Input)
25
23
24
26
26
SCK (CPOL = 0)
(Output)
24
23
26
25
SCK (CPOL = 1)
(Output)
26
29
29
30
MISO
(Input)
30
MSB
Valid
LSB
Valid
33
MOSI
(Output)
34
MSB
LSB
40
41
42
HREQ
(Input)
43
Figure 8. SPI Master Timing (CPHA = 1)
38
PRELIMINARY
Freescale Semiconductor
Serial Host Interface SPI Protocol Timing
SS
(Input)
25
23
24
26
28
26
39
SCK (CPOL = 0)
(Input)
27
24
23
26
25
26
SCK (CPOL = 1)
(Input)
35
33
34
31
MISO
(Output)
34
32
MSB
LSB
29
29
30
MOSI
(Input)
MSB
Valid
30
LSB
Valid
36
38
HREQ
(Output)
Figure 9. SPI Slave Timing (CPHA = 0)
Freescale Semiconductor
PRELIMINARY
39
Serial Host Interface (SHI) I2C Protocol Timing
SS
(Input)
25
23
24
26
28
26
SCK (CPOL = 0)
(Input)
27
24
26
25
26
SCK (CPOL = 1)
(Input)
33
33
34
31
MISO
(Output)
32
MSB
LSB
29
29
30
MOSI
(Input)
30
MSB
Valid
LSB
Valid
36
37
HREQ
(Output)
Figure 10. SPI Slave Timing (CPHA = 1)
Serial Host Interface (SHI) I2C Protocol Timing
13
Table 22. SHI I2C Protocol Timing
Standard I2C
No.
XX
40
Characteristics1,2,3,4,5
Tolerable Spike Width on SCL or SDA
Symbol/
Expression
Standard
Min
Fast-Mode
Max
Min
Unit
Max
—
Filters Bypassed
—
0
—
0
ns
Very Narrow Filters enabled
—
10
—
10
ns
Narrow Filters enabled
—
50
—
50
ns
Wide Fileters enabled.
—
100
—
100
ns
44
SCL clock frequency
FSCL
—
100
—
400
kHz
44
SCL clock cycle
TSCL
10
—
2.5
—
µs
45
Bus free time
TBUF
4.7
—
1.3
—
µs
46
Start condition set-up time
TSUSTA
4.7
—
0.6
—
µs
PRELIMINARY
Freescale Semiconductor
Serial Host Interface (SHI) I2C Protocol Timing
Table 22. SHI I2C Protocol Timing (Continued)
Standard I2C
Characteristics1,2,3,4,5
No.
Standard
Fast-Mode
Unit
Symbol/
Expression
Min
Max
Min
Max
THD;STA
4.0
—
0.6
—
µs
47
Start condition hold time
48
SCL low period
TLOW
4.7
—
1.3
—
µs
49
SCL high period
THIGH
4.0
—
1.3
—
µs
50
SCL and SDA rise time
TR
—
5.0
—
5.0
ns
51
SCL and SDA fall time
TF
—
5.0
—
5.0
ns
52
Data set-up time
TSU;DAT
250
—
100
—
ns
53
Data hold time
THD;DAT
0.0
—
0.0
0.9
µs
54
DSP clock frequency
• Filters bypassed
10.6
—
28.5
—
MHz
• Very Narrrow filters enabled
10.6
—
28.5
—
MHz
• Narrow filters enabled
11.8
—
39.7
—
MHz
• Wide filters enabled
13.1
—
61.0
—
MHz
FOSC
55
SCL low to data out valid
TVD;DAT
—
3.4
—
0.9
µs
56
Stop condition setup time
TSU;STO
4.0
—
0.6
—
µs
57
HREQ in deassertion to last SCL edge
(HREQ in set-up time)
tSU;RQI
0.0
—
0.0
—
ns
58
First SCL sampling edge to HREQ output
deassertion2
—
57.0
—
57.0
ns
—
77.0
—
67.0
ns
—
157.0
—
157.0
ns
—
257.0
—
257.0
ns
44
—
44
—
ns
54
—
54
—
ns
94
—
94
—
ns
144
—
144
—
ns
• Filters bypassed
4327
—
927
—
ns
• Very Narrow filters enabled
4317
—
917
—
ns
• Narrow filters enabled
4282
—
877
—
ns
• Wide filters enabled
4227
—
827
—
ns
0.0
—
0.0
—
ns
• Filters bypassed
• Very Narrow filters enabled
• Narrow filters enabled
• Wide filters enabled
59
Last SCL edge to HREQ output not
deasserted2
• Filters bypassed
• Very Narrow filters enabled
• Narrow filters enabled
• Wide filters enabled
60
61
Note:
HREQ in assertion to first SCL edge
First SCL edge to HREQ is not asserted
(HREQ in hold time.)
1.
2.
3.
4.
5.
TNG;RQO
4 × TC + 30
4 × TC + 50
4 × TC + 130
4 × TC + 230
TAS;RQO
2 × TC + 30
2 × TC + 40
2 × TC + 80
2 × TC + 130
TAS;RQI
tHO;RQI
VCORE_VDD = 1.2 5 ± 0.05 V; TJ = 0°C to 95°C (52 LQFP) / 0°C to 90°C (80 LQFP), CL = 50 pF
Pull-up resistor: R P (min) = 1.5 kOhm
Capacitive load: C b (max) = 50 pF
All times assume noise free inputs
All times assume internal clock frequency of 150MHz
Freescale Semiconductor
PRELIMINARY
41
Programming the Serial Clock
14
Programming the Serial Clock
The programmed serial clock cycle, T I2CCP , is specified by the value of the HDM[7:0] and HRS bits of the HCKR (SHI clock control
register).
The expression for T I2CCP is
T I2CCP = [TC × 2 × (HDM[7:0] + 1) × (7 × (1 – HRS) + 1)]
where
—
HRS is the prescaler rate select bit. When HRS is cleared, the fixed
divide-by-eight prescaler is operational. When HRS is set, the prescaler is bypassed.
— HDM[7:0] are the divider modulus select bits. A divide ratio from 1 to 256 (HDM[7:0] = $00 to $FF) may be selected.
In I2C mode, the user may select a value for the programmed serial clock cycle from
6 × TC
(if HDM[7:0] = $02 and HRS = 1)
4096 × TC
(if HDM[7:0] = $FF and HRS = 0)
to
The programmed serial clock cycle (TI2CCP ) should be chosen in order to achieve the desired SCL serial clock cycle (TSCL), as
shown in Table 23.
Table 23. SCL Serial Clock Cycle (TSCL) Generated as Master
TI2CCP + 3 × TC + 45ns + TR
Nominal
44
46
49
48
SCL
50
SDA
Stop
53
51
45
52
Start
MSB
47
60
LSB
58
61
55
ACK
Stop
56
57
59
HREQ
Figure 11. I2C Timing
42
PRELIMINARY
Freescale Semiconductor
Enhanced Serial Audio Interface Timing
15
Enhanced Serial Audio Interface Timing
Table 24. Enhanced Serial Audio Interface Timing
No.
62
63
Characteristics1, 2, 3
5
Clock cycle
Symbol
Expression3
Min
Max
Condition4
Unit
tSSICC
4 × Tc
26.4
—
i ck
ns
4 × Tc
26.4
—
i ck
Clock high period
ns
• For internal clock
—
2 × Tc − 10.0
3.4
—
2 × Tc
13.4
—
2 × Tc − 10.0
3.4
—
2 × Tc
13.4
—
—
—
37.0
x ck
—
22.0
i ck a
—
37.0
x ck
—
22.0
i ck a
—
39.0
x ck
—
24.0
i ck a
—
39.0
x ck
—
24.0
i ck a
—
36.0
x ck
—
21.0
i ck a
—
37.0
x ck
—
22.0
i ck a
0.0
—
x ck
19.0
—
i ck
5.0
—
x ck
3.0
—
i ck
23.0
—
x ck
1.0
—
i ck a
23.0
—
x ck
1.0
—
i ck a
3.0
—
x ck
0.0
—
i ck a
0.0
—
x ck
19.0
—
i ck s
6.0
—
x ck
0.0
—
i ck s
—
29.0
x ck
—
15.0
i ck
• For external clock
64
Clock low period
ns
• For internal clock
—
• For external clock
65
66
67
68
69
70
71
72
73
74
75
76
77
78
SCKR rising edge to FSR out (bl) high
SCKR rising edge to FSR out (bl) low
SCKR rising edge to FSR out (wr)
high6
SCKR rising edge to FSR out (wr)
low6
SCKR rising edge to FSR out (wl) high
SCKR rising edge to FSR out (wl) low
—
—
—
—
—
—
Data in setup time before SCKR (SCK in
synchronous mode) falling edge
—
Data in hold time after SCKR falling edge
—
FSR input (bl, wr) high before SCKR falling
edge 6
—
FSR input (wl) high before SCKR falling
edge
—
FSR input hold time after SCKR falling edge
—
Flags input setup before SCKR falling edge
—
Flags input hold time after SCKR falling
edge
—
SCKT rising edge to FST out (bl) high
—
Freescale Semiconductor
PRELIMINARY
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
43
Enhanced Serial Audio Interface Timing
Table 24. Enhanced Serial Audio Interface Timing (Continued)
No.
79
Characteristics1, 2, 3
SCKT rising edge to FST out (bl) low
6
80
SCKT rising edge to FST out (wr) high
81
low6
82
83
84
85
86
87
88
89
90
91
SCKT rising edge to FST out (wr)
SCKT rising edge to FST out (wl) high
SCKT rising edge to FST out (wl) low
Symbol
Expression3
Min
Max
Condition4
Unit
—
—
—
31.0
x ck
ns
—
17.0
i ck
—
31.0
x ck
—
17.0
i ck
—
33.0
x ck
—
19.0
i ck
—
30.0
x ck
—
16.0
i ck
—
31.0
x ck
—
17.0
i ck
—
31.0
x ck
—
17.0
i ck
—
34.0
x ck
—
20.0
i ck
—
26.5
x ck
—
21.0
i ck
—
31.0
x ck
—
16.0
i ck
—
34.0
x ck
—
20.0
i ck
2.0
—
x ck
21.0
—
i ck
2.0
—
x ck
21.0
—
i ck
4.0
—
x ck
0.0
—
i ck
—
—
—
—
SCKT rising edge to data out enable from
high impedance
—
SCKT rising edge to transmitter #0 drive
enable assertion
—
SCKT rising edge to data out valid
—
SCKT rising edge to data out high
impedance7
—
SCKT rising edge to transmitter #0 drive
enable deassertion7
—
FST input (bl, wr) setup time before SCKT
falling edge6
—
FST input (wl) setup time before SCKT
falling edge
—
FST input hold time after SCKT falling edge
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
92
FST input (wl) to data out enable from high
impedance
—
—
—
27.0
—
ns
93
FST input (wl) to transmitter #0 drive enable
assertion
—
—
—
31.0
—
ns
94
Flag output valid after SCKT rising edge
—
—
—
32.0
x ck
ns
—
18.0
i ck
95
HCKR/HCKT clock cycle
—
2 x TC
13.4
—
ns
96
HCKT input rising edge to SCKT output
—
—
—
18.0
ns
97
HCKR input rising edge to SCKR output
—
—
—
18.0
ns
44
PRELIMINARY
Freescale Semiconductor
Enhanced Serial Audio Interface Timing
Table 24. Enhanced Serial Audio Interface Timing (Continued)
No.
Note:
Characteristics1, 2, 3
Symbol
Expression3
Min
Max
Condition4
Unit
1. VCORE_VDD = 1.25 ± 0.05 V; TJ = 0°C to 95°C (52 LQFP) / 0°C to 90°C (80 LQFP), CL = 50 pF
2. i ck = internal clock
x ck = external clock
i ck a = internal clock, asynchronous mode
(asynchronous implies that SCKT and SCKR are two different clocks)
i ck s = internal clock, synchronous mode
(synchronous implies that SCKT and SCKR are the same clock)
3. bl = bit length
wl = word length
wr = word length relative
4. SCKT(SCKT pin) = transmit clock
SCKR(SCKR pin) = receive clock
FST(FST pin) = transmit frame sync
FSR(FSR pin) = receive frame sync
HCKT(HCKT pin) = transmit high frequency clock
HCKR(HCKR pin) = receive high frequency clock
5. For the internal clock, the external clock cycle is defined by Icyc and the ESAI control register.
6. The word-relative frame sync signal waveform relative to the clock operates in the same manner as the bit-length frame sync signal
waveform, but spreads from one serial clock before first bit clock (same as bit length frame sync signal), until the one before last bit
clock of the first word in frame.
7. Periodically sampled and not 100% tested.
8. ESAI_1 specs match those of ESAI.
Freescale Semiconductor
PRELIMINARY
45
Enhanced Serial Audio Interface Timing
62
63
64
SCKT
(Input/Output)
78
79
FST (Bit)
Out
82
FST (Word)
Out
83
86
86
84
87
Data Out
First Bit
Last Bit
93
Transmitter #0
Drive Enable
(Internal Signal)
89
85
88
91
FST (Bit) In
92
91
90
FST (Word) In
94
See Note
Flags Out
Note: In network mode, output flag transitions can occur at the start of each time slot within the
frame. In normal mode, the output flag state is asserted for the entire frame period.
Figure 12. ESAI Transmitter Timing
46
PRELIMINARY
Freescale Semiconductor
Enhanced Serial Audio Interface Timing
62
63
64
SCKR
(Input/Output)
65
66
FSR (Bit)
Out
69
70
FSR (Word)
Out
72
71
Data In
First Bit
Last Bit
75
73
FSR (Bit)
In
74
75
FSR (Word)
In
76
77
Flags In
Figure 13. ESAI Receiver Timing
Freescale Semiconductor
PRELIMINARY
47
Timer Timing
HCKT
SCKT(output)
95
96
Figure 14. ESAI HCKT Timing
HCKR
SCKR (output)
95
97
Figure 15. ESAI HCKR Timing
16
Timer Timing
Table 25. Timer Timing
150 MHz
No.
Characteristics
Expression
Unit
Min
Max
98
TIO Low
2 × TC + 2.0
15.4
—
ns
99
TIO High
2 × TC + 2.0
15.4
—
ns
Note: VCORE_VDD = 1.25 V ± 0.05 V; TJ = 0°C to 95°C (52 LQFP) / 0°C to 90°C (80 LQFP), CL = 50 pF
TIO
98
99
Figure 16. TIO Timer Event Input Restrictions
17
48
GPIO Timing
PRELIMINARY
Freescale Semiconductor
GPIO Timing
Table 26. GPIO Timing
Characteristics1
No.
Expression
2
Min
Max
Unit
100
FOSC edge to GPIO out valid (GPIO out delay time)
—
7
ns
101
FOSC edge to GPIO out not valid (GPIO out hold time)2
—
7
ns
102
FOSC In valid to EXTAL edge (GPIO in set-up time)
2
2
—
ns
103
FOSC edge to GPIO in not valid (GPIO in hold time)2
0
—
ns
104
Minimum GPIO pulse high width
2 x TC
13.4
—
ns
105
Minimum GPIO pulse low width
2 x TC
13.4
—
ns
106
GPIO out rise time
—
—
13.0
ns
107
GPIO out fall time
—
—
13.0
ns
Note:
1. VCORE_VDD = 1.25 V ± 0.05 V; TJ = -40°C to +115°C, CL = 50 pF
2. Simulation numbers-subject to change.
FOSC
100
101
GPIO
(Output)
102
GPIO
(Input)
103
Valid
GPIO
(Output)
104
106
105
107
Figure 17. GPIO Timing
Freescale Semiconductor
PRELIMINARY
49
JTAG Timing
18
JTAG Timing
Table 27. JTAG Timing
All frequencies
No.
Characteristics
Unit
Min
Max
—
10.0
MHz
108
TCK frequency of operation (1/(TC × 3); maximum 10 MHz)
109
TCK cycle time in Crystal mode
100.0
—
ns
110
TCK clock pulse width measured at 1.65 V
50.0
—
ns
111
TCK rise and fall times
—
3.0
ns
112
Boundary scan input data setup time
15.0
—
ns
113
Boundary scan input data hold time
24.0
—
ns
114
TCK low to output data valid
—
40.0
ns
115
TCK low to output high impedance
—
40.0
ns
116
TMS, TDI data setup time
5.0
—
ns
117
TMS, TDI data hold time
25.0
—
ns
118
TCK low to TDO data valid
—
44.0
ns
119
TCK low to TDO high impedance
—
44.0
ns
Note:
1. VCORE_VDD = 1.25 V ± 0.05 V; TJ = -40°C to +95°C, CL = 50 pF
2. All timings apply to OnCE module data transfers because it uses the JTAG port as an interface.
109
TCK
(Input)
VIH
110
110
VM
VM
VIL
111
111
Figure 18. Test Clock Input Timing Diagram
50
PRELIMINARY
Freescale Semiconductor
JTAG Timing
TCK
(Input)
VIH
VIL
112
Data
Inputs
113
Input Data Valid
114
Data
Outputs
Output Data Valid
115
Data
Outputs
114
Data
Outputs
Output Data Valid
Figure 19. Debugger Port Timing Diagram
TCK
(Input)
VIH
VIL
116
TDI
TMS
(Input)
117
Input Data Valid
118
TDO
(Output)
Output Data Valid
119
TDO
(Output)
118
TDO
(Output)
Output Data Valid
Figure 20. Test Access Port Timing Diagram
Freescale Semiconductor
PRELIMINARY
51
Watchdog Timer Timing
19
Watchdog Timer Timing
Table 28. Watchdog Timer Timing
No.
52
Characteristics
Expression
Min
Max
Unit
120
Delay from time-out to fall of TIO1
2 × Tc
13.4
—
ns
121
Delay from timer clear to rise of TIO1
2 x Tc
13.4
—
ns
PRELIMINARY
Freescale Semiconductor
Appendix A Package Information
Appendix A Package Information
HCKT_1_PE5
SCAN
IO_Vdd
63
62
61
HCKR_PC2
HCKT_PC5
64
HCKR_1_PE2
66
65
SCKT_PC3
SCKT_1_PE3
67
SCKR_PC0
69
68
Core_Gnd
SCKR_1_PE0
74
70
FST_1_PE4
75
71
FST_PC4
76
GPIO_PG14
FSR_PC1
77
Core_Vdd
FSR_1_PE1
78
72
SDO4_PC7
79
73
IO_Gnd
SDO5_PC6
80
DSP56374 Pinout
46
XTAL
16
45
EXTAL
MOSI_HA0
17
44
PLLD_Vdd
GPIO_PG8
18
43
PLLD_Gnd
GPIO_PG7
19
42
PLLP_Gnd
IO_Gnd
20
41
PLLP_Vdd
39
15
MISO_SDA
40
SCK_SCL
PLLA_Gnd
IO_Vdd
PLLA_Vdd
47
38
14
GPIO_PG0
PINIT_NMI
SS_HA2
37
SDO0_1_PE11
48
36
49
13
GPIO_PG1
12
HREQ_PH4
GPIO_PG2
GPIO_PG9
35
SDO1_1_PE10
RESET_B
50
33
11
34
Core_Gnd
GPIO_PG10
GPIO_PG3
51
Core_Gnd
10
31
Core_Vdd
Core_Gnd
32
SDO2_1_PE9
52
Core_Vdd
53
9
PLOCK/TIO2
8
Core_Vdd
30
GPIO_PG11
WDT/TIO1
SDO3_1_PE8
29
54
TIO00
7
28
SDO0_PC11
MODD_IRQD_PH3
GPIO_PG4
55
27
6
TCK
SDO1_PC10
MODC_IRQC_PH2
26
56
TMS
5
25
SDO2_PC9
GPIO_PG12
24
SDO3_PC8
57
TDI
58
4
TDO
3
GPIO_PG13
23
MODB_IRQB_PH1
22
SDO4_1_PE7
GPIO_PG5
SDO5_1_PE6
59
21
60
2
GPIO_PG6
1
MODA_IRQA_PH0
IO_Vdd
IO_Vdd
1.25V
Filter
3.3V
Figure 21. 80-pin Vdd Connections
Freescale Semiconductor
PRELIMINARY
53
SCAN
IO_Vdd
40
26
PLLA_Gnd
41
25
PLLA_Vdd
HCKR_PC2
44
HCKT_PC5
SCKT_PC3
45
42
Core_Gnd
SCKR_PC0
46
FST_PC4
Core_Vdd
47
49
48
SDO4_PC7
FSR_PC1
50
IO_Gnd
SDO5_PC6
51
43
24
13
RESET_B
12
IO_Gnd
23
MOSI_HA0
22
11
Core_Gnd
MISO_SDA
Core_Vdd
10
21
SCK_SCL
20
9
PLOCK/TIO2
8
SS_HA2
WDT/TIO1
HREQ_PH4
19
7
18
6
Core_Gnd
TIO00
Core_Vdd
TCK
5
17
MODD_IRQD_PH3
16
4
TMS
MODC_IRQC_PH2
TDI
3
15
MODB_IRQB_PH1
14
2
TDO
1
MODA_IRQA_PH0
IO_Vdd
IO_Vdd
52
Appendix A Package Information
39
SDO3_PC8
38
SDO2_PC9
37
SDO1_PC10
36
SDO0_PC11
35
Core_Vdd
34
Core_Gnd
33
PINIT_NMI
32
XTAL
31
EXTAL
30
PLLD_Vdd
29
PLLD_Gnd
28
PLLP_Gnd
27
PLLP_Vdd
1.25V
Filter
3.3V
Figure 22. 52-pin Vdd Connections
19.1
54
Signal Identification by Pin Number
PRELIMINARY
Freescale Semiconductor
Appendix A Package Information
19.2
Package Information
80 pin package
.
Freescale Semiconductor
PRELIMINARY
55
Appendix A Package Information
56
PRELIMINARY
Freescale Semiconductor
Appendix A Package Information
Freescale Semiconductor
PRELIMINARY
57
Appendix A Package Information
.
58
PRELIMINARY
Freescale Semiconductor
Appendix A Package Information
52 pin package
Freescale Semiconductor
PRELIMINARY
59
Appendix A Package Information
60
PRELIMINARY
Freescale Semiconductor
Appendix A Package Information
Freescale Semiconductor
PRELIMINARY
61
Appendix A Package Information
62
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
Appendix B IBIS Model
[IBIS ver]
2.1
[File name]
tpz013g3.ibs
[File Rev]
1.0
[Date]
07/30/2002
[Source]
Made By 0.13uu HSPICE model.
[Disclaimer]
This information is for modeling purposes only and is not
guaranteed.
[Copyright]
Copyright 2002, Design Service, tsmc, All Rights Reserved.
|
|************************************************************************
|
Component tpz013g3
|************************************************************************
(Pin)
1
signal_name
IO_VDD
2 MODA_IRQA_PH0
model_name
PVDD2DGZ/PVDD2POC
PDU12SDGZ
3
MODB_IRQB_PH1
4
GPIO_PG13
PDU12SDGZ
PRD12DGZ
5
GPIO_PG12
PRD12DGZ
6
MODC_IRQC_PH2
PDU12SDGZ
7
MODD_IRQD_PH3
PDU12SDGZ
8
GPIO_PG11
PRD12DGZ
9
CORE_VDD
PVDD1DGZ
10
CORE_GND
PVSS3DGZ
11
GPIO_PG10
PRD12DGZ
12
GPIO_PG9
PRD12DGZ
13
HREQ_PH4
PDU12SDGZ
14
SS_HA2
PDUSDGZ
15
SCK_SCL
PDU12SDGZ
16
MISO_SDA
PDU16SDGZ
17
MOSI_HA0
PDU12SDGZ
18
GPIO_PG8
PRD12DGZ
19
GPIO_PG7
PRD12DGZ
20
IO_GND
PVSS3DGZ
21
IO_VDD
PVDD2DGZ
22
GPIO_PG6
PRD12DGZ
23
GPIO_PG5
PRD12DGZ
24
TDO
PRT24DGZ
25
TDI
PDUDGZ
26
TCK
PDUDGZ
TMS
PDUDGZ
27
28
GPIO_PG4
Freescale Semiconductor
PRD12DGZ
PRELIMINARY
63
Appendix B IBIS Model
29
TIO0_PB0
PRD12DGZ
30
WDT_TIO1_PB1
PRD12DGZ
31
PLOCK_TIO1_PB2
PRD12DGZ
32
CORE_VDD
PVDD1DGZ
33
CORE_GND
PVSS3DGZ
34
GPIO_PG3
PRD12DGZ
35
RESET_B
PDUSDGZ
36
GPIO_PG2
PRD12DGZ
37
GPIO_PG1
PRD12DGZ
38
GPIO_PG0
PRD12DGZ
39
PLLA_VDD
PVDD1P
40
PLLA_GND
PVSS1P
41
PLLP_VDD
PVDD2DGZ
42
PLLP_GND
PVSS2P
43
PLLD_GND
PVSS1P
44
PLLD_VDD
PVDD1PC
45
EXTAL
1/2 PDX03DGZ
46
XTAL
1/2 PDX03DGZ
47
IO_VDD
PVDD2DGZ
48
PINIT_NMI
PDUSDGZ
49
SDO0_1_PE11
PRD12DGZ
50
SDO1_1_PE10
PRD12DGZ
51
CORE_GND
PVSS3DGZ
52
CORE_VDD
PVDD1DGZ
53
SDO2_1_PE9
PRD12DGZ
54
SDO3_1_PE8
PRD12DGZ
55
SDO0_PC11
PRD12DGZ
56
SDO1_PC10
PRD12DGZ
57
SDO2_SDI3_PC9
PRD12DGZ
58
SDO3_SDI2_PC8
PRD12DGZ
59
SDO4_1_PE7
PRD12DGZ
60
SDO5_1_PC6
PRD12DGZ
61
IO_VDD
PVDD2DGZ
62
SCAN
63
HCKT_1_PE5
PRD12DGZ
64
HCKT_PC5
PRD12DGZ
65
HCKR_PC2
PRD12DGZ
66
HCKR_1_PE2
PRD12DGZ
PDDDGZ
67
SCKT_1_PE3
PRD12DGZ
68
SCKT_PC3
PRD12DGZ
69
SCKR_PC0
PRD12DGZ
70
SCKR_1_PE0
PRD12DGZ
71
CORE_GND
PVSS3DGZ
72
CORE_VDD
PVDD1DGZ
64
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
73
GPIO_PG14
PRD12DGZ
74
FST_1_PE4
PRD12DGZ
75
FST_PC4
PRD12DGZ
76
FSR_PC1
PRD12DGZ
FSR_1_PE1
PRD12DGZ
77
78
SDO4_SDI1_PC7
PRD12DGZ
|************************************************************************
|
Model prd12dgz
|************************************************************************
|
[Model]
prd12dgz
Model_type
I/O
Polarity
Non-Inverting
Enable
Active-Low
Vinl =
0.80V
Vinh =
2.00V
Vmeas =
1.50V
Cref =
50.00pF
Rref =
1.00M
Vref =
0.000V
C_comp
4.17pF
3.75pF
4.58pF
|
|
[Temperature Range]
25.00
0.12k
0.000
[Pullup Reference]
3.30V
3.00V
3.60V
[Pulldown Reference]
0.000V
0.000V
0.000V
[POWER Clamp Reference]
5.00V
4.50V
5.50V
[GND Clamp Reference]
0.000V
0.000V
0.000V
[Pulldown]
| voltage
I(typ)
I(min)
I(max)
-3.30
0.000A
0.000A
0.000A
-3.10
0.000A
0.000A
-10.00mA
-2.90
0.000A
0.000A
0.000A
-2.70
0.000A
0.000A
0.000A
-2.50
0.000A
-10.00mA
0.000A
-2.30
-10.00mA
0.000A
-10.00mA
-2.10
0.000A
-10.00mA
0.000A
-1.90
0.000A
0.000A
-10.00mA
-1.70
0.000A
0.000A
-10.00mA
-1.50
-10.00mA
0.000A
-10.00mA
-1.00
-11.00mA
-5.00mA
-13.00mA
-0.90
-12.00mA
-5.00mA
-15.00mA
-0.80
-24.00mA
-7.00mA
-32.51mA
|
Freescale Semiconductor
PRELIMINARY
65
Appendix B IBIS Model
66
-0.70
-29.14mA
-8.00mA
-32.35mA
-0.60
-26.47mA
-13.80mA
-29.35mA
-0.50
-22.61mA
-14.54mA
-25.54mA
-0.40
-18.32mA
-12.17mA
-20.93mA
-0.30
-13.87mA
-9.16mA
-15.91mA
-0.20
-9.33mA
-6.10mA
-10.74mA
-0.10
-4.70mA
-3.05mA
-5.43mA
-0.00
2.86nA
7.25nA
11.72nA
0.10
4.61mA
2.94mA
5.36mA
0.20
8.96mA
5.69mA
10.49mA
0.30
13.07mA
8.26mA
15.36mA
0.40
16.92mA
10.65mA
20.00mA
0.50
20.53mA
12.86mA
24.40mA
0.60
23.91mA
14.90mA
28.55mA
0.70
27.04mA
16.76mA
32.48mA
0.80
29.95mA
18.46mA
36.18mA
0.90
32.61mA
19.99mA
39.64mA
1.00
35.06mA
21.37mA
42.87mA
1.10
37.27mA
22.58mA
45.87mA
1.20
39.27mA
23.64mA
48.64mA
1.30
41.04mA
24.55mA
51.19mA
1.40
42.60mA
25.32mA
53.50mA
1.50
43.95mA
25.95mA
55.60mA
1.60
45.08mA
26.44mA
57.46mA
1.70
46.00mA
26.80mA
59.11mA
1.80
46.70mA
27.07mA
60.53mA
1.90
47.20mA
27.26mA
61.71mA
2.00
47.55mA
27.41mA
62.63mA
2.10
47.81mA
27.53mA
63.31mA
2.20
48.01mA
27.63mA
63.79mA
2.30
48.17mA
27.71mA
64.15mA
2.40
48.31mA
27.78mA
64.43mA
2.50
48.42mA
27.85mA
64.65mA
2.60
48.53mA
27.90mA
64.84mA
2.70
48.62mA
27.96mA
65.00mA
2.80
48.70mA
28.01mA
65.14mA
2.90
48.78mA
28.05mA
65.27mA
3.00
48.85mA
28.09mA
65.38mA
3.10
48.92mA
28.14mA
65.49mA
3.20
48.99mA
28.18mA
65.59mA
3.30
49.05mA
28.23mA
65.68mA
3.40
49.12mA
28.42mA
65.77mA
3.50
49.20mA
28.97mA
65.86mA
3.60
49.24mA
29.74mA
65.95mA
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
3.70
49.31mA
30.57mA
66.04mA
3.80
49.40mA
31.13mA
66.12mA
3.90
49.61mA
28.60mA
66.22mA
4.00
50.41mA
28.66mA
66.33mA
4.10
51.65mA
28.72mA
66.49mA
4.20
52.87mA
28.80mA
66.72mA
4.30
50.78mA
28.89mA
67.28mA
4.50
50.67mA
29.12mA
70.40mA
4.70
51.17mA
29.42mA
73.03mA
4.90
51.85mA
29.83mA
69.12mA
5.10
52.75mA
30.37mA
70.18mA
5.30
53.86mA
31.02mA
71.45mA
5.50
55.21mA
31.82mA
73.05mA
5.70
56.82mA
32.77mA
74.98mA
5.90
58.68mA
33.86mA
77.25mA
6.10
60.78mA
35.10mA
79.83mA
6.60
66.91mA
38.73mA
87.50mA
I(typ)
I(min)
I(max)
|
[Pullup]
| voltage
|
-3.30
0.11A
82.01mA
0.13A
-3.10
0.11A
79.25mA
0.13A
-2.90
0.10A
76.07mA
0.12A
-2.70
97.60mA
72.55mA
0.11A
-2.50
92.41mA
68.70mA
0.11A
-2.30
87.04mA
64.55mA
0.10A
-2.10
81.44mA
60.13mA
94.69mA
-1.90
75.56mA
55.45mA
87.72mA
-1.70
69.36mA
50.52mA
80.48mA
-1.50
62.83mA
45.36mA
73.03mA
-1.00
48.46mA
31.37mA
56.75mA
-0.90
43.82mA
28.63mA
50.74mA
-0.80
38.59mA
28.69mA
44.61mA
-0.70
33.28mA
24.97mA
38.60mA
-0.60
28.26mA
21.04mA
33.20mA
-0.50
23.64mA
17.11mA
27.91mA
-0.40
19.01mA
13.34mA
22.52mA
-0.30
14.32mA
9.87mA
17.03mA
-0.20
9.58mA
6.53mA
11.45mA
-0.10
4.80mA
3.23mA
5.78mA
0.00
34.08uA
11.20uA
71.92uA
0.10
-4.58mA
-3.08mA
-5.50mA
0.20
-8.94mA
-5.98mA
-10.80mA
Freescale Semiconductor
PRELIMINARY
67
Appendix B IBIS Model
68
0.30
-13.04mA
-8.72mA
-15.82mA
0.40
-16.89mA
-11.27mA
-20.56mA
0.50
-20.50mA
-13.66mA
-25.04mA
0.60
-23.86mA
-15.87mA
-29.25mA
0.70
-26.98mA
-17.92mA
-33.21mA
0.80
-29.87mA
-19.80mA
-36.91mA
0.90
-32.53mA
-21.51mA
-40.36mA
1.00
-34.96mA
-23.06mA
-43.56mA
1.10
-37.16mA
-24.45mA
-46.52mA
1.20
-39.15mA
-25.68mA
-49.24mA
1.30
-40.92mA
-26.75mA
-51.73mA
1.40
-42.48mA
-27.66mA
-53.98mA
1.50
-43.83mA
-28.43mA
-56.01mA
1.60
-44.98mA
-29.05mA
-57.81mA
1.70
-45.94mA
-29.53mA
-59.40mA
1.80
-46.72mA
-29.90mA
-60.77mA
1.90
-47.35mA
-30.20mA
-61.93mA
2.00
-47.86mA
-30.45mA
-62.90mA
2.10
-48.29mA
-30.66mA
-63.70mA
2.20
-48.65mA
-30.85mA
-64.37mA
2.30
-48.97mA
-31.02mA
-64.93mA
2.40
-49.25mA
-31.17mA
-65.40mA
2.50
-49.50mA
-31.31mA
-65.82mA
2.60
-49.72mA
-31.44mA
-66.18mA
2.70
-49.92mA
-31.56mA
-66.50mA
2.80
-50.11mA
-31.67mA
-66.79mA
2.90
-50.28mA
-31.78mA
-67.05mA
3.00
-50.44mA
-31.88mA
-67.29mA
3.10
-50.59mA
-31.98mA
-67.51mA
3.20
-50.74mA
-32.08mA
-67.72mA
3.30
-50.88mA
-32.20mA
-67.92mA
3.40
-51.01mA
-32.75mA
-68.11mA
3.50
-51.14mA
-40.35mA
-68.29mA
3.60
-51.27mA
-0.14A
-68.47mA
3.70
-51.42mA
-0.94A
-68.64mA
3.80
-51.84mA
-2.69A
-68.80mA
3.90
-53.78mA
-4.48A
-68.97mA
4.00
-64.80mA
-6.27A
-69.30mA
4.10
-0.29A
-8.06A
-70.82mA
4.20
-1.85A
-9.85A
-75.29mA
4.30
-3.90A
-11.63A
-83.12mA
4.50
-8.00A
-15.21A
-1.14A
4.70
-12.10A
-18.79A
-5.39A
4.90
-16.20A
-22.36A
-9.64A
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
5.10
-20.30A
-25.94A
-13.89A
5.30
-24.40A
-29.51A
-18.15A
5.50
-28.50A
-33.09A
-22.41A
5.70
-32.60A
-36.67A
-26.66A
5.90
-36.70A
-40.24A
-30.92A
6.10
-40.80A
-43.82A
-35.17A
6.60
-51.05A
-52.76A
-45.81A
I(typ)
I(min)
I(max)
-5.00
-85.83A
-77.78A
-88.32A
-4.80
-81.73A
-74.20A
-84.06A
-4.60
-77.63A
-70.62A
-79.80A
-4.40
-73.53A
-67.04A
-75.54A
-4.20
-69.43A
-63.46A
-71.28A
-4.00
-65.33A
-59.88A
-67.02A
-3.80
-61.23A
-56.30A
-62.76A
-3.60
-57.13A
-52.72A
-58.50A
-3.40
-53.03A
-49.14A
-54.24A
-3.20
-48.93A
-45.56A
-49.98A
-3.00
-44.84A
-41.99A
-45.73A
-2.80
-40.74A
-38.42A
-41.48A
-2.60
-36.64A
-34.84A
-37.22A
-2.40
-32.54A
-31.27A
-32.97A
-2.20
-28.45A
-27.69A
-28.72A
-2.00
-24.35A
-24.12A
-24.46A
-1.80
-20.25A
-20.54A
-20.21A
-1.60
-16.15A
-16.97A
-15.95A
-1.40
-12.05A
-13.39A
-11.70A
-1.20
-7.95A
-9.82A
-7.44A
-1.00
-3.85A
-6.24A
-3.19A
-0.80
-0.23A
-2.66A
-70.99mA
-0.60
-2.25mA
-0.10A
-5.98mA
-0.40
-89.81uA
-0.52mA
-0.26mA
-0.20
-27.92uA
-14.70uA
-42.92uA
-0.00
-87.63nA
-89.05nA
-0.10uA
0.20
18.71uA
7.31uA
32.27uA
0.40
29.19uA
10.25uA
54.12uA
0.60
32.49uA
10.67uA
65.78uA
0.80
33.07uA
10.78uA
69.33uA
1.00
33.30uA
10.86uA
70.17uA
1.20
33.45uA
10.92uA
70.55uA
1.40
33.57uA
10.97uA
70.80uA
|
[GND_clamp]
| voltage
|
Freescale Semiconductor
PRELIMINARY
69
Appendix B IBIS Model
1.60
33.68uA
11.02uA
70.99uA
1.80
33.77uA
11.07uA
71.16uA
2.00
33.87uA
11.11uA
71.32uA
2.20
33.96uA
11.14uA
71.46uA
2.40
34.01uA
11.15uA
71.61uA
2.60
34.03uA
11.16uA
71.76uA
2.80
34.05uA
11.17uA
71.84uA
3.00
34.06uA
11.19uA
71.86uA
3.20
34.07uA
11.51uA
71.88uA
3.40
34.07uA
10.95uA
71.90uA
3.60
34.07uA
10.39uA
71.92uA
3.80
34.07uA
9.83uA
71.94uA
4.00
34.07uA
9.27uA
71.96uA
4.20
34.07uA
8.71uA
71.98uA
4.40
34.07uA
8.15uA
72.00uA
4.60
34.07uA
7.59uA
72.02uA
4.80
34.07uA
7.03uA
72.04uA
5.00
34.07uA
6.47uA
72.06uA
|
[POWER_clamp]
| voltage
I(typ)
I(min)
I(max)
-5.00
48.57uA
16.33uA
95.57uA
-4.90
48.24uA
16.21uA
95.07uA
-4.80
47.91uA
16.09uA
94.57uA
-4.70
47.58uA
15.97uA
94.07uA
-4.60
47.25uA
15.85uA
93.57uA
-4.50
46.92uA
15.73uA
93.07uA
-4.40
46.59uA
15.61uA
92.57uA
-4.30
46.26uA
15.49uA
92.07uA
-4.20
45.93uA
15.37uA
91.57uA
-4.10
45.60uA
15.25uA
91.07uA
-4.00
45.27uA
15.13uA
90.57uA
-3.90
44.94uA
15.01uA
90.07uA
-3.80
44.61uA
14.89uA
89.57uA
-3.70
44.28uA
14.77uA
89.07uA
-3.60
43.95uA
14.65uA
88.57uA
-3.50
43.62uA
14.53uA
88.07uA
-3.40
43.29uA
14.41uA
87.57uA
-3.30
42.96uA
14.29uA
87.07uA
-3.20
42.63uA
14.17uA
86.57uA
-3.10
42.30uA
14.05uA
86.07uA
-3.00
41.97uA
13.93uA
85.57uA
-2.90
41.64uA
13.81uA
85.07uA
|
70
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
-2.80
41.31uA
13.69uA
84.57uA
-2.70
40.98uA
13.57uA
84.07uA
-2.60
40.65uA
13.45uA
83.57uA
-2.50
40.32uA
13.33uA
83.07uA
-2.40
39.99uA
13.21uA
82.57uA
-2.30
39.66uA
13.09uA
82.07uA
-2.20
39.33uA
12.97uA
81.57uA
-2.10
39.00uA
12.85uA
81.07uA
-2.00
38.67uA
12.73uA
80.57uA
-1.90
38.34uA
12.61uA
80.07uA
-1.80
38.01uA
12.49uA
79.57uA
-1.70
37.68uA
12.37uA
79.07uA
-1.60
37.35uA
12.25uA
78.57uA
-1.50
37.02uA
12.15uA
78.07uA
-1.40
36.71uA
12.05uA
77.57uA
-1.30
36.42uA
11.95uA
77.07uA
-1.20
36.15uA
11.87uA
76.57uA
-1.10
35.89uA
11.79uA
76.07uA
-1.00
35.66uA
11.72uA
75.57uA
-0.90
35.45uA
11.66uA
75.10uA
-0.80
35.26uA
11.60uA
74.67uA
-0.70
35.09uA
11.55uA
74.28uA
-0.60
34.93uA
11.51uA
73.93uA
-0.50
34.80uA
11.47uA
73.61uA
-0.40
34.68uA
11.43uA
73.34uA
-0.30
34.59uA
11.41uA
73.10uA
-0.20
34.50uA
11.38uA
72.89uA
-0.10
34.43uA
11.36uA
72.72uA
0.00
34.37uA
11.34uA
72.57uA
|
[Ramp]
| variable
typ
min
max
dV/dt_r
1.21/2.06n
0.85/2.62n
1.45/1.82n
dV/dt_f
1.22/2.51n
0.78/3.11n
1.45/2.14n
V(min)
V(max)
R_load = 50.00
|
[Rising Waveform]
R_fixture = 50.00
V_fixture = 0.000
V_fixture_min = 0.000
V_fixture_max = 0.000
L_fixture = 0.000H
C_fixture = 0.000F
| time
Freescale Semiconductor
V(typ)
PRELIMINARY
71
Appendix B IBIS Model
|
0.000S
72
1.26uV
1.62uV
1.22uV
0.20nS
1.04uV
1.45uV
0.74uV
0.40nS
-5.64uV
-1.36uV
11.59uV
0.60nS
-0.29mV
-5.13uV
-3.27mV
0.80nS
-3.54mV
25.94uV
-9.17mV
1.00nS
-3.50mV
-4.79uV
56.24mV
1.20nS
33.86mV
-0.86mV
0.13V
1.40nS
79.34mV
-3.75mV
0.19V
1.60nS
0.14V
-8.09mV
0.27V
1.80nS
0.20V
3.52mV
0.36V
2.00nS
0.28V
38.97mV
0.47V
2.20nS
0.36V
82.84mV
0.59V
2.40nS
0.47V
0.13V
0.74V
2.60nS
0.60V
0.18V
0.90V
2.80nS
0.77V
0.27V
1.12V
3.00nS
0.92V
0.34V
1.32V
3.20nS
1.03V
0.40V
1.46V
3.40nS
1.16V
0.50V
1.63V
3.60nS
1.29V
0.59V
1.78V
3.80nS
1.39V
0.67V
1.91V
4.00nS
1.49V
0.75V
2.01V
4.20nS
1.58V
0.84V
2.11V
4.40nS
1.65V
0.91V
2.18V
4.60nS
1.69V
0.95V
2.21V
4.80nS
1.72V
0.99V
2.23V
5.00nS
1.76V
1.03V
2.27V
5.20nS
1.80V
1.07V
2.29V
5.40nS
1.83V
1.12V
2.31V
5.60nS
1.86V
1.16V
2.33V
5.80nS
1.88V
1.18V
2.34V
6.00nS
1.89V
1.20V
2.34V
6.20nS
1.91V
1.23V
2.35V
6.40nS
1.92V
1.25V
2.36V
6.60nS
1.93V
1.27V
2.37V
6.80nS
1.94V
1.28V
2.38V
7.00nS
1.95V
1.30V
2.38V
7.20nS
1.96V
1.31V
2.39V
7.40nS
1.97V
1.33V
2.39V
7.60nS
1.98V
1.34V
2.39V
7.80nS
1.98V
1.35V
2.40V
8.00nS
1.98V
1.36V
2.40V
8.20nS
1.99V
1.37V
2.40V
8.40nS
1.99V
1.37V
2.40V
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
8.60nS
1.99V
1.38V
2.41V
8.80nS
2.00V
1.39V
2.41V
9.00nS
2.00V
1.39V
2.41V
9.20nS
2.00V
1.40V
2.41V
9.40nS
2.01V
1.40V
2.41V
9.60nS
2.01V
1.41V
2.42V
9.80nS
2.01V
1.41V
2.42V
10.00nS
2.01V
1.41V
2.42V
V(typ)
V(min)
V(max)
1.27V
1.66V
1.18V
0.20nS
1.27V
1.66V
1.18V
0.40nS
1.27V
1.66V
1.18V
0.60nS
1.27V
1.66V
1.19V
0.80nS
1.28V
1.66V
1.24V
1.00nS
1.40V
1.66V
1.47V
1.20nS
1.60V
1.67V
1.71V
1.40nS
1.77V
1.69V
1.88V
1.60nS
1.99V
1.80V
2.12V
1.80nS
2.24V
1.95V
2.41V
2.00nS
2.50V
2.13V
2.70V
2.20nS
2.74V
2.32V
2.99V
2.40nS
2.94V
2.49V
3.21V
2.60nS
3.09V
2.63V
3.34V
2.80nS
3.18V
2.79V
3.44V
3.00nS
3.24V
2.87V
3.49V
3.20nS
3.26V
2.91V
3.52V
3.40nS
3.27V
2.96V
3.55V
3.60nS
3.29V
2.98V
3.57V
3.80nS
3.29V
2.99V
3.59V
4.00nS
3.30V
2.99V
3.59V
4.20nS
3.30V
3.00V
3.60V
4.40nS
3.30V
3.00V
3.60V
4.60nS
3.30V
3.00V
3.60V
4.80nS
3.30V
3.00V
3.60V
5.00nS
3.30V
3.00V
3.60V
|
[Rising Waveform]
R_fixture = 50.00
V_fixture = 3.30
V_fixture_min = 3.00
V_fixture_max = 3.60
L_fixture = 0.000H
C_fixture = 0.000F
| time
|
0.000S
Freescale Semiconductor
PRELIMINARY
73
Appendix B IBIS Model
5.20nS
3.30V
3.00V
3.60V
5.40nS
3.30V
3.00V
3.60V
5.60nS
3.30V
3.00V
3.60V
5.80nS
3.30V
3.00V
3.60V
6.00nS
3.30V
3.00V
3.60V
6.20nS
3.30V
3.00V
3.60V
6.40nS
3.30V
3.00V
3.60V
6.60nS
3.30V
3.00V
3.60V
6.80nS
3.30V
3.00V
3.60V
7.00nS
3.30V
3.00V
3.60V
7.20nS
3.30V
3.00V
3.60V
7.40nS
3.30V
3.00V
3.60V
7.60nS
3.30V
3.00V
3.60V
7.80nS
3.30V
3.00V
3.60V
8.00nS
3.30V
3.00V
3.60V
8.20nS
3.30V
3.00V
3.60V
8.40nS
3.30V
3.00V
3.60V
8.60nS
3.30V
3.00V
3.60V
8.80nS
3.30V
3.00V
3.60V
9.00nS
3.30V
3.00V
3.60V
9.20nS
3.30V
3.00V
3.60V
9.40nS
3.30V
3.00V
3.60V
9.60nS
3.30V
3.00V
3.60V
9.80nS
3.30V
3.00V
3.60V
10.00nS
3.30V
3.00V
3.60V
V(typ)
V(min)
V(max)
2.02V
1.44V
2.43V
0.20nS
2.02V
1.44V
2.43V
0.40nS
2.02V
1.44V
2.43V
0.60nS
2.02V
1.44V
2.38V
0.80nS
1.97V
1.44V
2.13V
1.00nS
1.73V
1.44V
1.82V
1.20nS
1.45V
1.42V
1.49V
1.40nS
1.24V
1.38V
1.24V
1.60nS
0.96V
1.29V
0.92V
|
[Falling Waveform]
R_fixture = 50.00
V_fixture = 0.000
V_fixture_min = 0.000
V_fixture_max = 0.000
L_fixture = 0.000H
C_fixture = 0.000F
| time
|
0.000S
74
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
1.80nS
0.70V
1.12V
0.67V
2.00nS
0.50V
0.92V
0.50V
2.20nS
0.36V
0.73V
0.38V
2.40nS
0.27V
0.55V
0.30V
2.60nS
0.20V
0.40V
0.24V
2.80nS
0.14V
0.27V
0.17V
3.00nS
99.16mV
0.20V
0.13V
3.20nS
79.41mV
0.16V
0.11V
3.40nS
53.08mV
0.11V
78.74mV
3.60nS
36.21mV
75.26mV
59.16mV
3.80nS
23.36mV
51.00mV
39.59mV
4.00nS
12.42mV
31.87mV
27.31mV
4.20nS
6.73mV
18.57mV
15.01mV
4.40nS
2.10mV
8.15mV
7.54mV
4.60nS
1.57mV
5.93mV
4.99mV
4.80nS
1.14mV
3.71mV
2.45mV
5.00nS
0.68mV
1.71mV
1.29mV
5.20nS
0.62mV
1.31mV
0.88mV
5.40nS
0.54mV
0.89mV
0.54mV
5.60nS
0.46mV
0.73mV
0.46mV
5.80nS
0.41mV
0.65mV
0.42mV
6.00nS
0.37mV
0.59mV
0.38mV
6.20nS
0.34mV
0.53mV
0.34mV
6.40nS
0.32mV
0.48mV
0.29mV
6.60nS
0.27mV
0.43mV
0.26mV
6.80nS
0.22mV
0.38mV
0.22mV
7.00nS
0.18mV
0.34mV
0.20mV
7.20nS
0.18mV
0.30mV
0.18mV
7.40nS
0.18mV
0.26mV
0.15mV
7.60nS
0.15mV
0.23mV
0.13mV
7.80nS
0.12mV
0.22mV
0.12mV
8.00nS
0.11mV
0.20mV
0.11mV
8.20nS
0.11mV
0.18mV
0.10mV
8.40nS
0.12mV
0.17mV
92.36uV
8.60nS
97.87uV
0.16mV
78.53uV
8.80nS
59.73uV
0.15mV
64.71uV
9.00nS
36.18uV
0.14mV
61.02uV
9.20nS
61.23uV
0.12mV
60.74uV
9.40nS
87.87uV
0.10mV
58.12uV
9.60nS
67.13uV
0.10mV
46.02uV
9.80nS
29.42uV
0.10mV
39.81uV
10.00nS
71.42uV
84.83uV
50.29uV
|
[Falling Waveform]
Freescale Semiconductor
PRELIMINARY
75
Appendix B IBIS Model
R_fixture = 50.00
V_fixture = 3.30
V_fixture_min = 3.00
V_fixture_max = 3.60
L_fixture = 0.000H
C_fixture = 0.000F
| time
V(typ)
V(min)
V(max)
|
0.000S
76
3.30V
3.00V
3.60V
0.20nS
3.30V
3.00V
3.60V
0.40nS
3.30V
3.00V
3.60V
0.60nS
3.30V
3.00V
3.59V
0.80nS
3.30V
3.00V
3.48V
1.00nS
3.22V
3.00V
3.36V
1.20nS
3.12V
3.00V
3.25V
1.40nS
3.06V
3.00V
3.16V
1.60nS
2.96V
3.00V
3.04V
1.80nS
2.86V
2.95V
2.90V
2.00nS
2.75V
2.89V
2.76V
2.20nS
2.64V
2.83V
2.61V
2.40nS
2.52V
2.77V
2.48V
2.60nS
2.40V
2.70V
2.34V
2.80nS
2.26V
2.61V
2.18V
3.00nS
2.16V
2.54V
2.04V
3.20nS
2.10V
2.48V
1.93V
3.40nS
2.01V
2.41V
1.79V
3.60nS
1.93V
2.35V
1.68V
3.80nS
1.86V
2.30V
1.57V
4.00nS
1.78V
2.25V
1.49V
4.20nS
1.68V
2.19V
1.41V
4.40nS
1.58V
2.13V
1.34V
4.60nS
1.53V
2.10V
1.31V
4.80nS
1.49V
2.08V
1.29V
5.00nS
1.43V
2.04V
1.26V
5.20nS
1.39V
2.01V
1.24V
5.40nS
1.35V
1.98V
1.22V
5.60nS
1.32V
1.95V
1.21V
5.80nS
1.31V
1.94V
1.20V
6.00nS
1.30V
1.93V
1.20V
6.20nS
1.29V
1.91V
1.19V
6.40nS
1.29V
1.90V
1.19V
6.60nS
1.29V
1.88V
1.19V
6.80nS
1.28V
1.87V
1.19V
7.00nS
1.28V
1.85V
1.19V
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
7.20nS
1.28V
1.84V
1.19V
7.40nS
1.28V
1.83V
1.19V
7.60nS
1.28V
1.82V
1.19V
7.80nS
1.28V
1.81V
1.19V
8.00nS
1.28V
1.81V
1.19V
8.20nS
1.28V
1.80V
1.19V
8.40nS
1.27V
1.79V
1.19V
8.60nS
1.27V
1.79V
1.19V
8.80nS
1.27V
1.78V
1.19V
9.00nS
1.27V
1.77V
1.19V
9.20nS
1.27V
1.76V
1.19V
9.40nS
1.27V
1.75V
1.19V
9.60nS
1.27V
1.73V
1.18V
9.80nS
1.27V
1.72V
1.18V
10.00nS
1.27V
1.71V
1.18V
|
| End [Model] prd12dgz
|
|************************************************************************
|
Model prd16dgz
|************************************************************************
|
[Model]
prd16dgz
Model_type
I/O
Polarity
Non-Inverting
Enable
Active-Low
Vinl =
0.80V
Vinh =
2.00V
Vmeas =
1.50V
Cref =
50.00pF
Rref =
1.00M
Vref =
0.000V
C_comp
3.86pF
3.48pF
4.25pF
|
|
[Temperature Range]
25.00
0.12k
0.000
[Pullup Reference]
3.30V
3.00V
3.60V
[Pulldown Reference]
0.000V
0.000V
0.000V
[POWER Clamp Reference]
5.00V
4.50V
5.50V
[GND Clamp Reference]
0.000V
0.000V
0.000V
[Pulldown]
| voltage
I(typ)
I(min)
I(max)
-10.00mA
0.000A
0.000A
|
-3.30
Freescale Semiconductor
PRELIMINARY
77
Appendix B IBIS Model
78
-3.10
0.000A
0.000A
0.000A
-2.90
0.000A
0.000A
0.000A
-2.70
0.000A
0.000A
0.000A
-2.50
0.000A
0.000A
0.000A
-2.30
0.000A
0.000A
0.000A
-2.10
-10.00mA
0.000A
0.000A
-1.90
0.000A
0.000A
-10.00mA
-1.70
-10.00mA
0.000A
-10.00mA
-1.50
-10.00mA
0.000A
-20.00mA
-1.00
-16.00mA
-6.00mA
-18.00mA
-0.90
-16.00mA
-8.00mA
-21.00mA
-0.80
-32.00mA
-8.00mA
-43.34mA
-0.70
-38.86mA
-10.60mA
-43.13mA
-0.60
-35.29mA
-18.40mA
-39.13mA
-0.50
-30.14mA
-19.39mA
-34.05mA
-0.40
-24.42mA
-16.22mA
-27.89mA
-0.30
-18.49mA
-12.22mA
-21.21mA
-0.20
-12.44mA
-8.14mA
-14.32mA
-0.10
-6.27mA
-4.06mA
-7.24mA
-0.00
4.09nA
6.98nA
10.67nA
0.10
6.14mA
3.92mA
7.15mA
0.20
11.95mA
7.59mA
13.98mA
0.30
17.42mA
11.01mA
20.48mA
0.40
22.56mA
14.20mA
26.67mA
0.50
27.38mA
17.14mA
32.53mA
0.60
31.88mA
19.86mA
38.07mA
0.70
36.06mA
22.35mA
43.31mA
0.80
39.93mA
24.61mA
48.24mA
0.90
43.49mA
26.66mA
52.85mA
1.00
46.74mA
28.49mA
57.16mA
1.10
49.69mA
30.11mA
61.16mA
1.20
52.35mA
31.52mA
64.86mA
1.30
54.72mA
32.74mA
68.25mA
1.40
56.80mA
33.76mA
71.34mA
1.50
58.59mA
34.59mA
74.13mA
1.60
60.11mA
35.25mA
76.62mA
1.70
61.33mA
35.74mA
78.81mA
1.80
62.26mA
36.09mA
80.70mA
1.90
62.93mA
36.35mA
82.27mA
2.00
63.40mA
36.55mA
83.51mA
2.10
63.75mA
36.71mA
84.41mA
2.20
64.01mA
36.84mA
85.06mA
2.30
64.23mA
36.95mA
85.54mA
2.40
64.41mA
37.04mA
85.91mA
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
2.50
64.56mA
37.13mA
86.20mA
2.60
64.70mA
37.21mA
86.45mA
2.70
64.82mA
37.28mA
86.66mA
2.80
64.94mA
37.34mA
86.85mA
2.90
65.04mA
37.40mA
87.02mA
3.00
65.14mA
37.46mA
87.17mA
3.10
65.23mA
37.51mA
87.32mA
3.20
65.32mA
37.57mA
87.45mA
3.30
65.40mA
37.63mA
87.58mA
3.40
65.49mA
37.81mA
87.70mA
3.50
65.59mA
38.34mA
87.82mA
3.60
65.66mA
39.10mA
87.93mA
3.70
65.75mA
39.94mA
88.05mA
3.80
65.86mA
40.42mA
88.16mA
3.90
66.08mA
38.09mA
88.29mA
4.00
66.86mA
38.16mA
88.44mA
4.10
68.11mA
38.25mA
88.63mA
4.20
69.36mA
38.35mA
88.90mA
4.30
67.34mA
38.47mA
89.46mA
4.50
67.43mA
38.78mA
92.67mA
4.70
68.10mA
39.19mA
95.47mA
4.90
69.00mA
39.73mA
91.91mA
5.10
70.20mA
40.44mA
93.29mA
5.30
71.67mA
41.32mA
95.00mA
5.50
73.47mA
42.38mA
97.12mA
5.70
75.61mA
43.64mA
99.69mA
5.90
78.09mA
45.10mA
0.10A
6.10
80.89mA
46.75mA
0.11A
6.60
89.06mA
51.59mA
0.12A
I(typ)
I(min)
I(max)
-3.30
0.16A
0.12A
0.19A
-3.10
0.16A
0.12A
0.18A
-2.90
0.15A
0.11A
0.17A
-2.70
0.14A
0.11A
0.16A
-2.50
0.14A
0.10A
0.16A
-2.30
0.13A
96.26mA
0.15A
-2.10
0.12A
89.72mA
0.14A
-1.90
0.11A
82.79mA
0.13A
-1.70
0.10A
75.47mA
0.12A
-1.50
93.76mA
67.80mA
0.11A
-1.00
70.54mA
46.98mA
82.43mA
|
[Pullup]
| voltage
|
Freescale Semiconductor
PRELIMINARY
79
Appendix B IBIS Model
80
-0.90
63.97mA
42.83mA
74.23mA
-0.80
56.74mA
41.47mA
65.83mA
-0.70
49.39mA
36.27mA
57.50mA
-0.60
42.27mA
30.78mA
49.67mA
-0.50
35.43mA
25.27mA
41.79mA
-0.40
28.50mA
19.90mA
33.74mA
-0.30
21.47mA
14.79mA
25.52mA
-0.20
14.35mA
9.79mA
17.14mA
-0.10
7.19mA
4.85mA
8.64mA
0.00
34.08uA
11.19uA
71.92uA
0.10
-6.89mA
-4.62mA
-8.29mA
0.20
-13.43mA
-8.98mA
-16.24mA
0.30
-19.58mA
-13.08mA
-23.77mA
0.40
-25.36mA
-16.92mA
-30.88mA
0.50
-30.77mA
-20.50mA
-37.60mA
0.60
-35.81mA
-23.82mA
-43.93mA
0.70
-40.49mA
-26.89mA
-49.86mA
0.80
-44.83mA
-29.70mA
-55.41mA
0.90
-48.81mA
-32.27mA
-60.59mA
1.00
-52.46mA
-34.60mA
-65.39mA
1.10
-55.77mA
-36.68mA
-69.83mA
1.20
-58.75mA
-38.52mA
-73.91mA
1.30
-61.41mA
-40.13mA
-77.64mA
1.40
-63.75mA
-41.50mA
-81.02mA
1.50
-65.77mA
-42.65mA
-84.06mA
1.60
-67.50mA
-43.58mA
-86.77mA
1.70
-68.93mA
-44.31mA
-89.14mA
1.80
-70.10mA
-44.87mA
-91.20mA
1.90
-71.04mA
-45.31mA
-92.94mA
2.00
-71.82mA
-45.68mA
-94.40mA
2.10
-72.46mA
-46.00mA
-95.60mA
2.20
-73.01mA
-46.28mA
-96.60mA
2.30
-73.48mA
-46.53mA
-97.44mA
2.40
-73.90mA
-46.76mA
-98.15mA
2.50
-74.27mA
-46.97mA
-98.77mA
2.60
-74.60mA
-47.17mA
-99.31mA
2.70
-74.91mA
-47.35mA
-99.80mA
2.80
-75.18mA
-47.52mA
-0.10A
2.90
-75.44mA
-47.68mA
-0.10A
3.00
-75.68mA
-47.83mA
-0.10A
3.10
-75.90mA
-47.97mA
-0.10A
3.20
-76.12mA
-48.11mA
-0.10A
3.30
-76.32mA
-48.27mA
-0.10A
3.40
-76.52mA
-48.87mA
-0.10A
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
3.50
-76.71mA
-56.48mA
-0.10A
3.60
-76.89mA
-0.15A
-0.10A
3.70
-77.09mA
-0.95A
-0.10A
3.80
-77.56mA
-2.71A
-0.10A
3.90
-79.54mA
-4.50A
-0.10A
4.00
-90.56mA
-6.29A
-0.10A
4.10
-0.31A
-8.09A
-0.11A
4.20
-1.88A
-9.88A
-0.11A
4.30
-3.93A
-11.66A
-0.12A
4.50
-8.04A
-15.24A
-1.17A
4.70
-12.14A
-18.83A
-5.43A
4.90
-16.25A
-22.41A
-9.69A
5.10
-20.36A
-25.99A
-13.95A
5.30
-24.46A
-29.57A
-18.21A
5.50
-28.57A
-33.15A
-22.48A
5.70
-32.68A
-36.73A
-26.74A
5.90
-36.78A
-40.31A
-31.00A
6.10
-40.89A
-43.89A
-35.27A
6.60
-51.16A
-52.84A
-45.93A
I(typ)
I(min)
I(max)
-5.00
-85.90A
-77.84A
-88.40A
-4.80
-81.80A
-74.26A
-84.14A
-4.60
-77.70A
-70.68A
-79.88A
-4.40
-73.60A
-67.10A
-75.62A
-4.20
-69.50A
-63.52A
-71.36A
-4.00
-65.40A
-59.94A
-67.10A
-3.80
-61.30A
-56.36A
-62.84A
-3.60
-57.20A
-52.78A
-58.58A
-3.40
-53.10A
-49.20A
-54.32A
-3.20
-49.00A
-45.62A
-50.06A
-3.00
-44.90A
-42.04A
-45.80A
-2.80
-40.80A
-38.46A
-41.54A
-2.60
-36.69A
-34.89A
-37.28A
-2.40
-32.59A
-31.31A
-33.02A
-2.20
-28.49A
-27.73A
-28.76A
-2.00
-24.38A
-24.15A
-24.50A
-1.80
-20.28A
-20.57A
-20.24A
-1.60
-16.17A
-16.99A
-15.97A
-1.40
-12.06A
-13.40A
-11.71A
-1.20
-7.96A
-9.83A
-7.45A
-1.00
-3.86A
-6.25A
-3.19A
|
[GND_clamp]
| voltage
|
Freescale Semiconductor
PRELIMINARY
81
Appendix B IBIS Model
-0.80
-0.23A
-2.66A
-70.76mA
-0.60
-2.22mA
-0.10A
-5.90mA
-0.40
-89.20uA
-0.52mA
-0.26mA
-0.20
-27.89uA
-14.67uA
-42.88uA
-0.00
-62.88nA
-63.80nA
-74.38nA
0.20
18.73uA
7.33uA
32.30uA
0.40
29.21uA
10.27uA
54.14uA
0.60
32.51uA
10.69uA
65.81uA
0.80
33.09uA
10.80uA
69.35uA
1.00
33.31uA
10.87uA
70.19uA
1.20
33.46uA
10.93uA
70.56uA
1.40
33.58uA
10.98uA
70.81uA
1.60
33.69uA
11.03uA
71.00uA
1.80
33.78uA
11.08uA
71.17uA
2.00
33.87uA
11.12uA
71.33uA
2.20
33.96uA
11.14uA
71.47uA
2.40
34.01uA
11.15uA
71.62uA
2.60
34.03uA
11.16uA
71.76uA
2.80
34.04uA
11.17uA
71.84uA
3.00
34.05uA
11.18uA
71.86uA
3.20
34.06uA
11.57uA
71.88uA
3.40
34.08uA
10.87uA
71.90uA
3.60
34.10uA
10.17uA
71.92uA
3.80
34.12uA
9.47uA
71.94uA
4.00
34.14uA
8.77uA
71.96uA
4.20
34.16uA
8.07uA
71.98uA
4.40
34.18uA
7.37uA
72.00uA
4.60
34.20uA
6.67uA
72.02uA
4.80
34.22uA
5.97uA
72.04uA
5.00
34.24uA
5.27uA
72.06uA
|
[POWER_clamp]
| voltage
I(typ)
I(min)
I(max)
-5.00
48.54uA
16.29uA
95.93uA
-4.90
48.21uA
16.17uA
95.42uA
-4.80
47.88uA
16.05uA
94.91uA
-4.70
47.55uA
15.93uA
94.40uA
-4.60
47.22uA
15.81uA
93.89uA
-4.50
46.89uA
15.69uA
93.38uA
-4.40
46.56uA
15.57uA
92.87uA
-4.30
46.23uA
15.45uA
92.36uA
-4.20
45.90uA
15.33uA
91.85uA
-4.10
45.57uA
15.21uA
91.34uA
|
82
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
-4.00
45.24uA
15.09uA
90.83uA
-3.90
44.91uA
14.97uA
90.32uA
-3.80
44.58uA
14.85uA
89.81uA
-3.70
44.25uA
14.73uA
89.30uA
-3.60
43.92uA
14.61uA
88.79uA
-3.50
43.59uA
14.49uA
88.28uA
-3.40
43.26uA
14.37uA
87.77uA
-3.30
42.93uA
14.25uA
87.26uA
-3.20
42.60uA
14.13uA
86.75uA
-3.10
42.27uA
14.01uA
86.24uA
-3.00
41.94uA
13.89uA
85.73uA
-2.90
41.61uA
13.77uA
85.22uA
-2.80
41.28uA
13.65uA
84.71uA
-2.70
40.95uA
13.53uA
84.20uA
-2.60
40.62uA
13.41uA
83.69uA
-2.50
40.29uA
13.29uA
83.18uA
-2.40
39.96uA
13.17uA
82.67uA
-2.30
39.63uA
13.05uA
82.16uA
-2.20
39.30uA
12.93uA
81.65uA
-2.10
38.97uA
12.81uA
81.14uA
-2.00
38.64uA
12.69uA
80.63uA
-1.90
38.31uA
12.57uA
80.12uA
-1.80
37.98uA
12.45uA
79.61uA
-1.70
37.65uA
12.33uA
79.10uA
-1.60
37.32uA
12.22uA
78.59uA
-1.50
36.99uA
12.11uA
78.08uA
-1.40
36.68uA
12.02uA
77.57uA
-1.30
36.39uA
11.92uA
77.06uA
-1.20
36.12uA
11.84uA
76.55uA
-1.10
35.87uA
11.76uA
76.04uA
-1.00
35.63uA
11.69uA
75.53uA
-0.90
35.42uA
11.63uA
75.06uA
-0.80
35.23uA
11.58uA
74.64uA
-0.70
35.06uA
11.53uA
74.25uA
-0.60
34.91uA
11.48uA
73.90uA
-0.50
34.78uA
11.44uA
73.58uA
-0.40
34.66uA
11.41uA
73.31uA
-0.30
34.56uA
11.38uA
73.07uA
-0.20
34.48uA
11.36uA
72.87uA
-0.10
34.41uA
11.34uA
72.69uA
0.00
34.35uA
11.32uA
72.55uA
|
[Ramp]
| variable
Freescale Semiconductor
typ
min
PRELIMINARY
max
83
Appendix B IBIS Model
dV/dt_r
1.43/2.06n
1.08/2.82n
1.66/1.86n
dV/dt_f
1.39/2.80n
0.98/4.41n
1.61/2.52n
V(min)
V(max)
R_load = 50.00
|
[Rising Waveform]
R_fixture = 50.00
V_fixture = 0.000
V_fixture_min = 0.000
V_fixture_max = 0.000
L_fixture = 0.000H
C_fixture = 0.000F
| time
V(typ)
|
0.000S
84
0.71uV
0.94uV
0.20nS
0.48uV
0.81uV
0.40nS
-6.07uV
-1.89uV
12.38uV
0.60nS
-0.29mV
-5.66uV
-3.13mV
0.80nS
-3.39mV
26.90uV
-6.39mV
1.00nS
-4.34mV
-5.17uV
43.34mV
1.20nS
25.79mV
-0.87mV
0.11V
1.40nS
62.40mV
-3.65mV
0.15V
1.60nS
0.11V
-7.89mV
0.21V
1.80nS
0.16V
0.71mV
0.28V
2.00nS
0.22V
29.71mV
0.37V
2.20nS
0.28V
65.63mV
0.46V
2.40nS
0.37V
0.10V
0.59V
2.60nS
0.48V
0.15V
0.71V
2.80nS
0.63V
0.22V
0.92V
3.00nS
0.79V
0.28V
1.12V
3.20nS
0.90V
0.34V
1.28V
3.40nS
1.07V
0.43V
1.49V
3.60nS
1.24V
0.53V
1.70V
3.80nS
1.39V
0.63V
1.89V
4.00nS
1.55V
0.74V
2.07V
4.20nS
1.71V
0.86V
2.24V
4.40nS
1.84V
0.97V
2.37V
4.60nS
1.90V
1.03V
2.44V
4.80nS
1.96V
1.09V
2.50V
5.00nS
2.03V
1.16V
2.54V
5.20nS
2.08V
1.22V
2.59V
5.40nS
2.13V
1.29V
2.62V
5.60nS
2.18V
1.36V
2.65V
5.80nS
2.20V
1.39V
2.66V
6.00nS
2.22V
1.43V
2.67V
PRELIMINARY
0.68uV
0.000V
Freescale Semiconductor
Appendix B IBIS Model
6.20nS
2.24V
1.47V
2.68V
6.40nS
2.26V
1.51V
2.69V
6.60nS
2.27V
1.54V
2.70V
6.80nS
2.29V
1.57V
2.71V
7.00nS
2.30V
1.60V
2.72V
7.20nS
2.31V
1.63V
2.72V
7.40nS
2.32V
1.66V
2.73V
7.60nS
2.33V
1.68V
2.74V
7.80nS
2.34V
1.69V
2.74V
8.00nS
2.34V
1.70V
2.74V
8.20nS
2.35V
1.72V
2.75V
8.40nS
2.35V
1.73V
2.75V
8.60nS
2.36V
1.74V
2.75V
8.80nS
2.36V
1.75V
2.76V
9.00nS
2.36V
1.76V
2.76V
9.20nS
2.37V
1.77V
2.76V
9.40nS
2.37V
1.78V
2.76V
9.60nS
2.38V
1.79V
2.77V
9.80nS
2.38V
1.80V
2.77V
10.00nS
2.38V
1.80V
2.77V
V(typ)
V(min)
V(max)
0.98V
1.34V
0.92V
0.20nS
0.98V
1.34V
0.92V
0.40nS
0.98V
1.34V
0.92V
0.60nS
0.98V
1.34V
0.92V
0.80nS
0.99V
1.34V
0.94V
1.00nS
1.05V
1.34V
1.07V
1.20nS
1.18V
1.34V
1.24V
1.40nS
1.31V
1.36V
1.37V
1.60nS
1.49V
1.44V
1.55V
1.80nS
1.69V
1.57V
1.76V
2.00nS
1.92V
1.73V
2.02V
2.20nS
2.18V
1.92V
2.33V
2.40nS
2.46V
2.11V
2.62V
2.60nS
2.73V
2.32V
2.91V
|
[Rising Waveform]
R_fixture = 50.00
V_fixture = 3.30
V_fixture_min = 3.00
V_fixture_max = 3.60
L_fixture = 0.000H
C_fixture = 0.000F
| time
|
0.000S
Freescale Semiconductor
PRELIMINARY
85
Appendix B IBIS Model
2.80nS
2.97V
2.55V
3.20V
3.00nS
3.09V
2.69V
3.33V
3.20nS
3.15V
2.76V
3.39V
3.40nS
3.20V
2.86V
3.44V
3.60nS
3.24V
2.92V
3.50V
3.80nS
3.26V
2.95V
3.53V
4.00nS
3.28V
2.98V
3.55V
4.20nS
3.29V
2.99V
3.57V
4.40nS
3.29V
2.99V
3.59V
4.60nS
3.30V
3.00V
3.59V
4.80nS
3.30V
3.00V
3.59V
5.00nS
3.30V
3.00V
3.60V
5.20nS
3.30V
3.00V
3.60V
5.40nS
3.30V
3.00V
3.60V
5.60nS
3.30V
3.00V
3.60V
5.80nS
3.30V
3.00V
3.60V
6.00nS
3.30V
3.00V
3.60V
6.20nS
3.30V
3.00V
3.60V
6.40nS
3.30V
3.00V
3.60V
6.60nS
3.30V
3.00V
3.60V
6.80nS
3.30V
3.00V
3.60V
7.00nS
3.30V
3.00V
3.60V
7.20nS
3.30V
3.00V
3.60V
7.40nS
3.30V
3.00V
3.60V
7.60nS
3.30V
3.00V
3.60V
7.80nS
3.30V
3.00V
3.60V
8.00nS
3.30V
3.00V
3.60V
8.20nS
3.30V
3.00V
3.60V
8.40nS
3.30V
3.00V
3.60V
8.60nS
3.30V
3.00V
3.60V
8.80nS
3.30V
3.00V
3.60V
9.00nS
3.30V
3.00V
3.60V
9.20nS
3.30V
3.00V
3.60V
9.40nS
3.30V
3.00V
3.60V
9.60nS
3.30V
3.00V
3.60V
9.80nS
3.30V
3.00V
3.60V
10.00nS
3.30V
3.00V
3.60V
|
[Falling Waveform]
R_fixture = 50.00
V_fixture = 0.000
V_fixture_min = 0.000
V_fixture_max = 0.000
L_fixture = 0.000H
86
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
C_fixture = 0.000F
| time
V(typ)
V(min)
V(max)
2.41V
1.87V
2.79V
0.20nS
2.41V
1.87V
2.79V
0.40nS
2.41V
1.87V
2.79V
0.60nS
2.41V
1.87V
2.76V
0.80nS
2.37V
1.87V
2.62V
1.00nS
2.24V
1.86V
2.44V
1.20nS
2.07V
1.85V
2.25V
1.40nS
1.94V
1.82V
2.10V
1.60nS
1.76V
1.75V
1.85V
1.80nS
1.54V
1.65V
1.55V
2.00nS
1.28V
1.51V
1.23V
2.20nS
1.01V
1.36V
0.96V
2.40nS
0.78V
1.18V
0.77V
2.60nS
0.61V
0.99V
0.63V
2.80nS
0.46V
0.76V
0.51V
3.00nS
0.37V
0.59V
0.43V
3.20nS
0.33V
0.49V
0.37V
3.40nS
0.26V
0.39V
0.32V
3.60nS
0.21V
0.31V
0.27V
3.80nS
0.17V
0.25V
0.22V
4.00nS
0.14V
0.19V
0.19V
4.20nS
0.10V
0.15V
0.14V
4.40nS
73.29mV
0.10V
0.11V
4.60nS
60.19mV
87.46mV
93.57mV
4.80nS
48.89mV
70.67mV
78.29mV
5.00nS
34.23mV
50.83mV
61.98mV
5.20nS
24.65mV
38.23mV
46.06mV
5.40nS
14.47mV
23.57mV
32.51mV
5.60nS
8.10mV
14.65mV
20.47mV
5.80nS
5.49mV
9.93mV
15.65mV
6.00nS
3.06mV
6.30mV
11.70mV
6.20nS
1.82mV
4.27mV
6.64mV
6.40nS
1.09mV
2.24mV
4.15mV
6.60nS
0.61mV
1.46mV
2.31mV
6.80nS
0.54mV
1.08mV
1.05mV
7.00nS
0.47mV
0.78mV
0.76mV
7.20nS
0.42mV
0.69mV
0.48mV
7.40nS
0.35mV
0.59mV
0.37mV
7.60nS
0.31mV
0.52mV
0.31mV
7.80nS
0.29mV
0.48mV
0.29mV
8.00nS
0.27mV
0.45mV
0.26mV
|
0.000S
Freescale Semiconductor
PRELIMINARY
87
Appendix B IBIS Model
8.20nS
0.24mV
0.40mV
0.24mV
8.40nS
0.20mV
0.35mV
0.21mV
8.60nS
0.18mV
0.32mV
0.18mV
8.80nS
0.18mV
0.31mV
0.16mV
9.00nS
0.17mV
0.28mV
0.16mV
9.20nS
0.15mV
0.24mV
0.15mV
9.40nS
0.12mV
0.20mV
0.12mV
9.60nS
0.10mV
0.19mV
93.74uV
9.80nS
0.11mV
0.20mV
90.71uV
10.00nS
0.11mV
0.17mV
97.83uV
|
[Falling Waveform]
R_fixture = 50.00
V_fixture = 3.30
V_fixture_min = 3.00
V_fixture_max = 3.60
L_fixture = 0.000H
C_fixture = 0.000F
| time
V(typ)
V(min)
V(max)
|
0.000S
88
3.30V
3.00V
3.60V
0.20nS
3.30V
3.00V
3.60V
0.40nS
3.30V
3.00V
3.60V
0.60nS
3.30V
3.00V
3.59V
0.80nS
3.30V
3.00V
3.52V
1.00nS
3.25V
3.00V
3.43V
1.20nS
3.17V
3.00V
3.34V
1.40nS
3.12V
3.00V
3.27V
1.60nS
3.05V
3.00V
3.17V
1.80nS
2.97V
2.97V
3.06V
2.00nS
2.87V
2.92V
2.95V
2.20nS
2.78V
2.87V
2.83V
2.40nS
2.68V
2.82V
2.70V
2.60nS
2.58V
2.76V
2.58V
2.80nS
2.45V
2.69V
2.43V
3.00nS
2.34V
2.62V
2.30V
3.20nS
2.26V
2.57V
2.21V
3.40nS
2.17V
2.50V
2.07V
3.60nS
2.07V
2.44V
1.91V
3.80nS
1.98V
2.38V
1.76V
4.00nS
1.89V
2.32V
1.62V
4.20nS
1.76V
2.25V
1.49V
4.40nS
1.63V
2.18V
1.37V
4.60nS
1.55V
2.15V
1.32V
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
4.80nS
1.48V
2.11V
1.27V
5.00nS
1.40V
2.06V
1.21V
5.20nS
1.32V
2.01V
1.16V
5.40nS
1.25V
1.96V
1.10V
5.60nS
1.19V
1.92V
1.06V
5.80nS
1.15V
1.89V
1.04V
6.00nS
1.13V
1.87V
1.02V
6.20nS
1.10V
1.84V
1.00V
6.40nS
1.07V
1.81V
0.98V
6.60nS
1.05V
1.78V
0.96V
6.80nS
1.03V
1.75V
0.95V
7.00nS
1.02V
1.72V
0.94V
7.20nS
1.01V
1.70V
0.93V
7.40nS
1.00V
1.67V
0.93V
7.60nS
1.00V
1.64V
0.92V
7.80nS
1.00V
1.62V
0.92V
8.00nS
1.00V
1.60V
0.92V
8.20nS
0.99V
1.57V
0.92V
8.40nS
0.99V
1.53V
0.92V
8.60nS
0.99V
1.50V
0.92V
8.80nS
0.99V
1.47V
0.92V
9.00nS
0.99V
1.44V
0.92V
9.20nS
0.99V
1.42V
0.92V
9.40nS
0.99V
1.40V
0.92V
9.60nS
0.99V
1.38V
0.92V
9.80nS
0.99V
1.37V
0.92V
10.00nS
0.99V
1.36V
0.92V
|
| End [Model] prd16dgz
|
|************************************************************************
|
Model prd24dgz
|************************************************************************
|
[Model]
prd24dgz
Model_type
I/O
Polarity
Non-Inverting
Enable
Active-Low
Vinl =
0.80V
Vinh =
2.00V
Vmeas =
1.50V
Cref =
50.00pF
Rref =
1.00M
Vref =
0.000V
Freescale Semiconductor
PRELIMINARY
89
Appendix B IBIS Model
C_comp
4.15pF
3.73pF
4.56pF
|
|
[Temperature Range]
25.00
0.12k
0.000
[Pullup Reference]
3.30V
3.00V
3.60V
[Pulldown Reference]
0.000V
0.000V
0.000V
[POWER Clamp Reference]
5.00V
4.50V
5.50V
[GND Clamp Reference]
0.000V
0.000V
0.000V
[Pulldown]
| voltage
I(typ)
I(min)
I(max)
-3.30
-10.00mA
0.000A
0.000A
-3.10
0.000A
0.000A
-10.00mA
-2.90
0.000A
0.000A
0.000A
-2.70
0.000A
0.000A
0.000A
-2.50
0.000A
0.000A
0.000A
-2.30
0.000A
0.000A
-10.00mA
-2.10
-10.00mA
0.000A
-10.00mA
-1.90
-10.00mA
0.000A
-10.00mA
-1.70
-10.00mA
-10.00mA
-10.00mA
-1.50
-10.00mA
-10.00mA
-20.00mA
-1.00
-19.00mA
-10.00mA
-23.00mA
-0.90
-21.00mA
-10.00mA
-26.00mA
-0.80
-41.70mA
-11.00mA
-55.33mA
-0.70
-50.61mA
-14.60mA
-55.12mA
-0.60
-46.07mA
-25.10mA
-50.21mA
-0.50
-39.45mA
-26.37mA
-43.90mA
-0.40
-32.03mA
-22.06mA
-36.08mA
-0.30
-24.29mA
-16.63mA
-27.48mA
-0.20
-16.36mA
-11.11mA
-18.57mA
-0.10
-8.26mA
-5.55mA
-9.40mA
-0.00
3.80nA
7.33nA
12.06nA
|
90
0.10
8.11mA
5.36mA
9.30mA
0.20
15.76mA
10.37mA
18.18mA
0.30
22.98mA
15.05mA
26.64mA
0.40
29.76mA
19.40mA
34.69mA
0.50
36.11mA
23.42mA
42.32mA
0.60
42.04mA
27.12mA
49.54mA
0.70
47.55mA
30.50mA
56.36mA
0.80
52.66mA
33.58mA
62.78mA
0.90
57.35mA
36.36mA
68.80mA
1.00
61.65mA
38.84mA
74.42mA
1.10
65.55mA
41.04mA
79.65mA
1.20
69.06mA
42.96mA
84.48mA
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
1.30
72.19mA
44.61mA
88.92mA
1.40
74.94mA
45.99mA
92.97mA
1.50
77.32mA
47.12mA
96.63mA
1.60
79.33mA
48.01mA
99.91mA
1.70
80.95mA
48.68mA
0.10A
1.80
82.19mA
49.17mA
0.11A
1.90
83.09mA
49.54mA
0.11A
2.00
83.74mA
49.83mA
0.11A
2.10
84.23mA
50.06mA
0.11A
2.20
84.62mA
50.25mA
0.11A
2.30
84.93mA
50.42mA
0.11A
2.40
85.20mA
50.57mA
0.11A
2.50
85.44mA
50.70mA
0.11A
2.60
85.65mA
50.82mA
0.11A
2.70
85.84mA
50.93mA
0.11A
2.80
86.01mA
51.03mA
0.11A
2.90
86.18mA
51.13mA
0.11A
3.00
86.33mA
51.22mA
0.11A
3.10
86.48mA
51.31mA
0.11A
3.20
86.62mA
51.40mA
0.11A
3.30
86.75mA
51.50mA
0.11A
3.40
86.89mA
51.73mA
0.12A
3.50
87.06mA
52.32mA
0.12A
3.60
87.16mA
53.14mA
0.12A
3.70
87.30mA
54.02mA
0.12A
3.80
87.47mA
54.48mA
0.12A
3.90
87.77mA
52.16mA
0.12A
4.00
88.66mA
52.28mA
0.12A
4.10
90.00mA
52.42mA
0.12A
4.20
91.34mA
52.58mA
0.12A
4.30
89.39mA
52.77mA
0.12A
4.50
89.66mA
53.24mA
0.12A
4.70
90.64mA
53.86mA
0.12A
4.90
91.94mA
54.68mA
0.12A
5.10
93.66mA
55.73mA
0.12A
5.30
95.77mA
57.03mA
0.13A
5.50
98.33mA
58.59mA
0.13A
5.70
0.10A
60.44mA
0.13A
5.90
0.10A
62.55mA
0.14A
6.10
0.11A
64.93mA
0.14A
6.60
0.12A
71.83mA
0.15A
|
[Pullup]
| voltage
I(typ)
Freescale Semiconductor
I(min)
PRELIMINARY
I(max)
91
Appendix B IBIS Model
|
92
-3.30
0.22A
0.16A
0.25A
-3.10
0.21A
0.16A
0.24A
-2.90
0.20A
0.15A
0.23A
-2.70
0.19A
0.14A
0.22A
-2.50
0.18A
0.14A
0.21A
-2.30
0.17A
0.13A
0.20A
-2.10
0.16A
0.12A
0.19A
-1.90
0.15A
0.11A
0.17A
-1.70
0.14A
0.10A
0.16A
-1.50
0.12A
90.15mA
0.14A
-1.00
92.80mA
62.50mA
0.11A
-0.90
84.30mA
57.02mA
97.94mA
-0.80
75.06mA
54.41mA
87.24mA
-0.70
65.63mA
47.70mA
76.50mA
-0.60
56.31mA
40.65mA
66.14mA
-0.50
47.22mA
33.53mA
55.68mA
-0.40
38.00mA
26.51mA
44.96mA
-0.30
28.62mA
19.71mA
34.00mA
-0.20
19.12mA
13.04mA
22.83mA
-0.10
9.57mA
6.46mA
11.50mA
0.00
34.08uA
11.19uA
71.92uA
0.10
-9.20mA
-6.16mA
-11.08mA
0.20
-17.92mA
-11.98mA
-21.68mA
0.30
-26.12mA
-17.45mA
-31.71mA
0.40
-33.83mA
-22.56mA
-41.21mA
0.50
-41.04mA
-27.33mA
-50.17mA
0.60
-47.76mA
-31.76mA
-58.60mA
0.70
-54.01mA
-35.85mA
-66.51mA
0.80
-59.78mA
-39.61mA
-73.91mA
0.90
-65.10mA
-43.04mA
-80.81mA
1.00
-69.96mA
-46.14mA
-87.22mA
1.10
-74.37mA
-48.91mA
-93.14mA
1.20
-78.35mA
-51.37mA
-98.58mA
1.30
-81.89mA
-53.51mA
-0.10A
1.40
-85.01mA
-55.34mA
-0.11A
1.50
-87.72mA
-56.87mA
-0.11A
1.60
-90.01mA
-58.11mA
-0.12A
1.70
-91.93mA
-59.08mA
-0.12A
1.80
-93.48mA
-59.83mA
-0.12A
1.90
-94.74mA
-60.42mA
-0.12A
2.00
-95.77mA
-60.91mA
-0.13A
2.10
-96.63mA
-61.34mA
-0.13A
2.20
-97.36mA
-61.71mA
-0.13A
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
2.30
-97.99mA
-62.05mA
-0.13A
2.40
-98.55mA
-62.36mA
-0.13A
2.50
-99.04mA
-62.64mA
-0.13A
2.60
-99.49mA
-62.90mA
-0.13A
2.70
-99.89mA
-63.14mA
-0.13A
2.80
-0.10A
-63.36mA
-0.13A
2.90
-0.10A
-63.57mA
-0.13A
3.00
-0.10A
-63.78mA
-0.13A
3.10
-0.10A
-63.97mA
-0.14A
3.20
-0.10A
-64.15mA
-0.14A
3.30
-0.10A
-64.35mA
-0.14A
3.40
-0.10A
-64.99mA
-0.14A
3.50
-0.10A
-72.69mA
-0.14A
3.60
-0.10A
-0.17A
-0.14A
3.70
-0.10A
-0.97A
-0.14A
3.80
-0.10A
-2.72A
-0.14A
3.90
-0.11A
-4.50A
-0.14A
4.00
-0.12A
-6.28A
-0.14A
4.10
-0.34A
-8.06A
-0.14A
4.20
-1.90A
-9.85A
-0.14A
4.30
-3.94A
-11.62A
-0.15A
4.50
-8.02A
-15.19A
-1.21A
4.70
-12.10A
-18.75A
-5.43A
4.90
-16.18A
-22.31A
-9.67A
5.10
-20.27A
-25.88A
-13.90A
5.30
-24.35A
-29.44A
-18.14A
5.50
-28.43A
-33.00A
-22.38A
5.70
-32.51A
-36.56A
-26.62A
5.90
-36.60A
-40.13A
-30.86A
6.10
-40.68A
-43.69A
-35.09A
6.60
-50.89A
-52.59A
-45.69A
I(typ)
I(min)
I(max)
-5.00
-85.26A
-77.43A
-87.91A
-4.80
-81.20A
-73.87A
-83.67A
-4.60
-77.14A
-70.31A
-79.43A
-4.40
-73.08A
-66.75A
-75.19A
-4.20
-69.02A
-63.19A
-70.95A
-4.00
-64.96A
-59.63A
-66.71A
-3.80
-60.90A
-56.07A
-62.47A
-3.60
-56.84A
-52.51A
-58.23A
-3.40
-52.78A
-48.95A
-53.99A
|
[GND_clamp]
| voltage
|
Freescale Semiconductor
PRELIMINARY
93
Appendix B IBIS Model
-3.20
-48.72A
-45.39A
-49.75A
-3.00
-44.64A
-41.83A
-45.52A
-2.80
-40.56A
-38.27A
-41.29A
-2.60
-36.48A
-34.71A
-37.05A
-2.40
-32.40A
-31.15A
-32.82A
-2.20
-28.32A
-27.59A
-28.58A
-2.00
-24.24A
-24.03A
-24.35A
-1.80
-20.16A
-20.47A
-20.11A
-1.60
-16.08A
-16.90A
-15.88A
-1.40
-12.00A
-13.34A
-11.64A
-1.20
-7.92A
-9.78A
-7.41A
-1.00
-3.84A
-6.22A
-3.18A
-0.80
-0.23A
-2.66A
-71.67mA
-0.60
-2.33mA
-0.10A
-6.23mA
-0.40
-91.55uA
-0.52mA
-0.28mA
-0.20
-27.91uA
-14.70uA
-42.94uA
-0.00
-75.80nA
-77.03nA
-90.19nA
0.20
18.72uA
7.32uA
32.29uA
0.40
29.20uA
10.26uA
54.13uA
0.60
32.50uA
10.68uA
65.79uA
0.80
33.08uA
10.79uA
69.34uA
1.00
33.30uA
10.86uA
70.18uA
1.20
33.45uA
10.92uA
70.55uA
1.40
33.57uA
10.98uA
70.80uA
1.60
33.68uA
11.03uA
71.00uA
1.80
33.78uA
11.07uA
71.16uA
2.00
33.87uA
11.11uA
71.32uA
2.20
33.96uA
11.14uA
71.47uA
2.40
34.01uA
11.15uA
71.61uA
2.60
34.03uA
11.16uA
71.76uA
2.80
34.04uA
11.17uA
71.84uA
3.00
34.05uA
11.18uA
71.86uA
3.20
34.06uA
11.75uA
71.88uA
3.40
34.08uA
10.69uA
71.90uA
3.60
34.10uA
9.63uA
71.92uA
3.80
34.12uA
8.57uA
71.94uA
4.00
34.14uA
7.51uA
71.96uA
4.20
34.16uA
6.45uA
71.98uA
4.40
34.18uA
5.39uA
72.00uA
4.60
34.20uA
4.33uA
72.02uA
4.80
34.22uA
3.27uA
72.04uA
5.00
34.24uA
2.21uA
72.06uA
|
[POWER_clamp]
94
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
| voltage
I(typ)
I(min)
I(max)
-5.00
48.55uA
16.31uA
95.55uA
-4.90
48.22uA
16.19uA
95.05uA
-4.80
47.89uA
16.07uA
94.55uA
-4.70
47.56uA
15.95uA
94.05uA
-4.60
47.23uA
15.83uA
93.55uA
-4.50
46.90uA
15.71uA
93.05uA
-4.40
46.57uA
15.59uA
92.55uA
-4.30
46.24uA
15.47uA
92.05uA
-4.20
45.91uA
15.35uA
91.55uA
-4.10
45.58uA
15.23uA
91.05uA
-4.00
45.25uA
15.11uA
90.55uA
-3.90
44.92uA
14.99uA
90.05uA
-3.80
44.59uA
14.87uA
89.55uA
-3.70
44.26uA
14.75uA
89.05uA
-3.60
43.93uA
14.63uA
88.55uA
-3.50
43.60uA
14.51uA
88.05uA
-3.40
43.27uA
14.39uA
87.55uA
-3.30
42.94uA
14.27uA
87.05uA
-3.20
42.61uA
14.15uA
86.55uA
-3.10
42.28uA
14.03uA
86.05uA
-3.00
41.95uA
13.91uA
85.55uA
-2.90
41.62uA
13.79uA
85.05uA
-2.80
41.29uA
13.67uA
84.55uA
-2.70
40.96uA
13.55uA
84.05uA
-2.60
40.63uA
13.43uA
83.55uA
-2.50
40.30uA
13.31uA
83.05uA
-2.40
39.97uA
13.19uA
82.55uA
-2.30
39.64uA
13.07uA
82.05uA
-2.20
39.31uA
12.95uA
81.55uA
-2.10
38.98uA
12.83uA
81.05uA
-2.00
38.65uA
12.71uA
80.55uA
-1.90
38.32uA
12.59uA
80.05uA
-1.80
37.99uA
12.47uA
79.55uA
-1.70
37.66uA
12.35uA
79.05uA
-1.60
37.33uA
12.23uA
78.55uA
-1.50
37.00uA
12.13uA
78.05uA
-1.40
36.69uA
12.03uA
77.55uA
-1.30
36.40uA
11.94uA
77.05uA
-1.20
36.13uA
11.85uA
76.55uA
-1.10
35.88uA
11.78uA
76.05uA
-1.00
35.64uA
11.71uA
75.55uA
-0.90
35.43uA
11.64uA
75.08uA
|
Freescale Semiconductor
PRELIMINARY
95
Appendix B IBIS Model
-0.80
35.24uA
11.59uA
74.65uA
-0.70
35.07uA
11.54uA
74.26uA
-0.60
34.92uA
11.49uA
73.91uA
-0.50
34.79uA
11.45uA
73.60uA
-0.40
34.67uA
11.42uA
73.32uA
-0.30
34.57uA
11.39uA
73.08uA
-0.20
34.49uA
11.37uA
72.88uA
-0.10
34.42uA
11.35uA
72.70uA
0.00
34.36uA
11.33uA
72.56uA
|
[Ramp]
| variable
typ
min
max
dV/dt_r
1.54/2.22n
1.20/2.88n
1.77/2.15n
dV/dt_f
1.52/3.16n
1.15/4.46n
1.73/3.00n
V(min)
V(max)
R_load = 50.00
|
[Rising Waveform]
R_fixture = 50.00
V_fixture = 0.000
V_fixture_min = 0.000
V_fixture_max = 0.000
L_fixture = 0.000H
C_fixture = 0.000F
| time
V(typ)
|
0.000S
96
0.70uV
0.92uV
0.20nS
0.45uV
0.77uV
0.40nS
-5.49uV
-1.76uV
16.07uV
0.60nS
-0.25mV
-4.97uV
-2.66mV
0.80nS
-2.88mV
24.27uV
-5.55mV
1.00nS
-3.85mV
-5.54uV
32.40mV
1.20nS
18.80mV
-0.76mV
80.52mV
1.40nS
45.63mV
-3.09mV
0.11V
1.60nS
80.05mV
-6.58mV
0.16V
1.80nS
0.11V
-0.18mV
0.21V
2.00nS
0.16V
21.52mV
0.27V
2.20nS
0.20V
48.21mV
0.33V
2.40nS
0.26V
76.15mV
0.41V
2.60nS
0.32V
0.11V
0.48V
2.80nS
0.41V
0.16V
0.61V
3.00nS
0.51V
0.19V
0.73V
3.20nS
0.58V
0.24V
0.82V
3.40nS
0.71V
0.30V
0.97V
3.60nS
0.85V
0.36V
1.16V
PRELIMINARY
0.68uV
0.000V
Freescale Semiconductor
Appendix B IBIS Model
3.80nS
1.00V
0.45V
1.35V
4.00nS
1.17V
0.54V
1.55V
4.20nS
1.38V
0.67V
1.80V
4.40nS
1.57V
0.80V
2.03V
4.60nS
1.68V
0.88V
2.15V
4.80nS
1.78V
0.96V
2.26V
5.00nS
1.91V
1.06V
2.39V
5.20nS
2.01V
1.15V
2.51V
5.40nS
2.13V
1.25V
2.61V
5.60nS
2.22V
1.34V
2.70V
5.80nS
2.27V
1.40V
2.74V
6.00nS
2.31V
1.44V
2.77V
6.20nS
2.35V
1.50V
2.80V
6.40nS
2.38V
1.56V
2.82V
6.60nS
2.41V
1.61V
2.84V
6.80nS
2.43V
1.66V
2.86V
7.00nS
2.45V
1.70V
2.87V
7.20nS
2.46V
1.74V
2.88V
7.40nS
2.48V
1.78V
2.89V
7.60nS
2.49V
1.82V
2.90V
7.80nS
2.50V
1.84V
2.91V
8.00nS
2.51V
1.86V
2.91V
8.20nS
2.52V
1.88V
2.92V
8.40nS
2.52V
1.90V
2.92V
8.60nS
2.53V
1.92V
2.92V
8.80nS
2.54V
1.93V
2.93V
9.00nS
2.54V
1.95V
2.93V
9.20nS
2.55V
1.96V
2.94V
9.40nS
2.55V
1.97V
2.94V
9.60nS
2.56V
1.98V
2.94V
9.80nS
2.56V
2.00V
2.95V
10.00nS
2.57V
2.00V
2.95V
V(typ)
V(min)
V(max)
0.76V
1.03V
0.72V
0.76V
1.03V
0.72V
|
[Rising Waveform]
R_fixture = 50.00
V_fixture = 3.30
V_fixture_min = 3.00
V_fixture_max = 3.60
L_fixture = 0.000H
C_fixture = 0.000F
| time
|
0.000S
0.20nS
Freescale Semiconductor
PRELIMINARY
97
Appendix B IBIS Model
98
0.40nS
0.76V
1.03V
0.72V
0.60nS
0.76V
1.03V
0.72V
0.80nS
0.77V
1.03V
0.73V
1.00nS
0.81V
1.03V
0.82V
1.20nS
0.90V
1.03V
0.93V
1.40nS
0.98V
1.04V
1.01V
1.60nS
1.09V
1.11V
1.13V
1.80nS
1.22V
1.20V
1.26V
2.00nS
1.35V
1.32V
1.42V
2.20nS
1.51V
1.45V
1.58V
2.40nS
1.69V
1.59V
1.78V
2.60nS
1.91V
1.74V
2.02V
2.80nS
2.22V
1.96V
2.36V
3.00nS
2.47V
2.16V
2.63V
3.20nS
2.65V
2.31V
2.82V
3.40nS
2.85V
2.49V
3.03V
3.60nS
2.97V
2.62V
3.17V
3.80nS
3.08V
2.73V
3.30V
4.00nS
3.14V
2.83V
3.36V
4.20nS
3.19V
2.89V
3.42V
4.40nS
3.23V
2.94V
3.47V
4.60nS
3.25V
2.95V
3.50V
4.80nS
3.27V
2.97V
3.52V
5.00nS
3.28V
2.98V
3.54V
5.20nS
3.29V
2.99V
3.56V
5.40nS
3.29V
2.99V
3.57V
5.60nS
3.30V
3.00V
3.58V
5.80nS
3.30V
3.00V
3.59V
6.00nS
3.30V
3.00V
3.59V
6.20nS
3.30V
3.00V
3.59V
6.40nS
3.30V
3.00V
3.60V
6.60nS
3.30V
3.00V
3.60V
6.80nS
3.30V
3.00V
3.60V
7.00nS
3.30V
3.00V
3.60V
7.20nS
3.30V
3.00V
3.60V
7.40nS
3.30V
3.00V
3.60V
7.60nS
3.30V
3.00V
3.60V
7.80nS
3.30V
3.00V
3.60V
8.00nS
3.30V
3.00V
3.60V
8.20nS
3.30V
3.00V
3.60V
8.40nS
3.30V
3.00V
3.60V
8.60nS
3.30V
3.00V
3.60V
8.80nS
3.30V
3.00V
3.60V
9.00nS
3.30V
3.00V
3.60V
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
9.20nS
3.30V
3.00V
3.60V
9.40nS
3.30V
3.00V
3.60V
9.60nS
3.30V
3.00V
3.60V
9.80nS
3.30V
3.00V
3.60V
10.00nS
3.30V
3.00V
3.60V
V(typ)
V(min)
V(max)
2.62V
2.12V
2.99V
0.20nS
2.62V
2.12V
2.99V
0.40nS
2.62V
2.12V
2.99V
0.60nS
2.62V
2.12V
2.96V
0.80nS
2.60V
2.12V
2.85V
1.00nS
2.50V
2.12V
2.72V
1.20nS
2.38V
2.11V
2.59V
1.40nS
2.29V
2.09V
2.50V
1.60nS
2.17V
2.04V
2.36V
1.80nS
2.04V
1.96V
2.20V
2.00nS
1.89V
1.85V
2.00V
2.20nS
1.71V
1.74V
1.76V
2.40nS
1.51V
1.63V
1.49V
2.60nS
1.27V
1.50V
1.23V
2.80nS
0.99V
1.33V
0.98V
3.00nS
0.81V
1.17V
0.83V
3.20nS
0.71V
1.04V
0.75V
3.40nS
0.59V
0.87V
0.66V
3.60nS
0.51V
0.72V
0.57V
3.80nS
0.44V
0.59V
0.50V
4.00nS
0.37V
0.49V
0.45V
4.20nS
0.31V
0.40V
0.38V
4.40nS
0.26V
0.33V
0.32V
4.60nS
0.23V
0.28V
0.29V
4.80nS
0.20V
0.25V
0.26V
5.00nS
0.17V
0.21V
0.23V
5.20nS
0.15V
0.18V
0.20V
5.40nS
0.12V
0.14V
0.17V
5.60nS
92.71mV
0.11V
0.14V
|
[Falling Waveform]
R_fixture = 50.00
V_fixture = 0.000
V_fixture_min = 0.000
V_fixture_max = 0.000
L_fixture = 0.000H
C_fixture = 0.000F
| time
|
0.000S
Freescale Semiconductor
PRELIMINARY
99
Appendix B IBIS Model
5.80nS
79.46mV
96.17mV
0.12V
6.00nS
67.17mV
83.01mV
0.11V
6.20nS
54.74mV
65.86mV
89.82mV
6.40nS
42.77mV
53.06mV
75.55mV
6.60nS
33.26mV
41.31mV
61.63mV
6.80nS
25.46mV
31.29mV
50.25mV
7.00nS
18.21mV
23.99mV
40.51mV
7.20nS
13.43mV
16.92mV
31.37mV
7.40nS
8.06mV
11.32mV
23.11mV
7.60nS
4.81mV
6.46mV
15.54mV
7.80nS
3.27mV
4.82mV
12.49mV
8.00nS
1.98mV
3.62mV
9.63mV
8.20nS
1.32mV
2.10mV
6.17mV
8.40nS
0.78mV
1.45mV
4.24mV
8.60nS
0.50mV
1.01mV
2.46mV
8.80nS
0.42mV
0.70mV
1.45mV
9.00nS
0.34mV
0.61mV
0.94mV
9.20nS
0.30mV
0.51mV
0.50mV
9.40nS
0.27mV
0.45mV
0.38mV
9.60nS
0.24mV
0.40mV
0.28mV
9.80nS
0.21mV
0.35mV
0.23mV
10.00nS
0.22mV
0.32mV
0.21mV
|
[Falling Waveform]
R_fixture = 50.00
V_fixture = 3.30
V_fixture_min = 3.00
V_fixture_max = 3.60
L_fixture = 0.000H
C_fixture = 0.000F
| time
V(typ)
V(min)
V(max)
|
0.000S
100
3.30V
3.00V
3.60V
0.20nS
3.30V
3.00V
3.60V
0.40nS
3.30V
3.00V
3.60V
0.60nS
3.30V
3.00V
3.59V
0.80nS
3.30V
3.00V
3.52V
1.00nS
3.25V
3.00V
3.44V
1.20nS
3.18V
3.00V
3.37V
1.40nS
3.14V
3.00V
3.32V
1.60nS
3.09V
3.00V
3.24V
1.80nS
3.03V
2.97V
3.16V
2.00nS
2.96V
2.92V
3.07V
2.20nS
2.88V
2.88V
2.98V
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
2.40nS
2.80V
2.84V
2.88V
2.60nS
2.72V
2.80V
2.78V
2.80nS
2.61V
2.74V
2.65V
3.00nS
2.51V
2.68V
2.55V
3.20nS
2.44V
2.64V
2.47V
3.40nS
2.34V
2.58V
2.35V
3.60nS
2.25V
2.52V
2.23V
3.80nS
2.15V
2.46V
2.09V
4.00nS
2.06V
2.39V
1.93V
4.20nS
1.93V
2.32V
1.75V
4.40nS
1.81V
2.24V
1.58V
4.60nS
1.73V
2.20V
1.50V
4.80nS
1.65V
2.15V
1.43V
5.00nS
1.54V
2.09V
1.34V
5.20nS
1.44V
2.04V
1.26V
5.40nS
1.32V
1.97V
1.18V
5.60nS
1.23V
1.91V
1.11V
5.80nS
1.18V
1.87V
1.07V
6.00nS
1.13V
1.84V
1.04V
6.20nS
1.08V
1.79V
1.00V
6.40nS
1.04V
1.75V
0.96V
6.60nS
1.00V
1.71V
0.92V
6.80nS
0.96V
1.67V
0.89V
7.00nS
0.93V
1.63V
0.87V
7.20nS
0.90V
1.59V
0.84V
7.40nS
0.87V
1.54V
0.82V
7.60nS
0.85V
1.48V
0.80V
7.80nS
0.83V
1.44V
0.78V
8.00nS
0.82V
1.40V
0.78V
8.20nS
0.81V
1.35V
0.76V
8.40nS
0.80V
1.31V
0.75V
8.60nS
0.79V
1.27V
0.75V
8.80nS
0.78V
1.23V
0.74V
9.00nS
0.78V
1.20V
0.73V
9.20nS
0.78V
1.17V
0.73V
9.40nS
0.77V
1.15V
0.73V
9.60nS
0.77V
1.12V
0.72V
9.80nS
0.77V
1.10V
0.72V
10.00nS
0.77V
1.09V
0.72V
|
| End [Model] prd24dgz
|
|************************************************************************
|
Freescale Semiconductor
Model prt24dgz
PRELIMINARY
101
Appendix B IBIS Model
|************************************************************************
|
[Model]
prt24dgz
Model_type
3-state
Polarity
Non-Inverting
Enable
Active-Low
Vmeas =
Cref =
1.50V
50.00pF
Rref =
1.00M
Vref =
0.000V
C_comp
4.09pF
3.68pF
4.50pF
|
|
[Temperature Range]
25.00
0.12k
0.000
[Pullup Reference]
3.30V
3.00V
3.60V
[Pulldown Reference]
0.000V
0.000V
0.000V
[POWER Clamp Reference]
5.00V
4.50V
5.50V
[GND Clamp Reference]
0.000V
0.000V
0.000V
[Pulldown]
| voltage
I(typ)
I(min)
I(max)
-3.30
-10.00mA
0.000A
0.000A
-3.10
0.000A
0.000A
-10.00mA
-2.90
0.000A
0.000A
0.000A
-2.70
0.000A
0.000A
0.000A
-2.50
0.000A
0.000A
0.000A
-2.30
0.000A
0.000A
-10.00mA
-2.10
-10.00mA
0.000A
-10.00mA
-1.90
-10.00mA
0.000A
-10.00mA
-1.70
-10.00mA
-10.00mA
-10.00mA
-1.50
-10.00mA
-10.00mA
-20.00mA
-1.00
-20.00mA
-10.00mA
-23.00mA
-0.90
-21.00mA
-10.00mA
-26.00mA
-0.80
-41.70mA
-12.00mA
-55.37mA
-0.70
-50.60mA
-14.60mA
-55.11mA
-0.60
-46.07mA
-25.10mA
-50.21mA
-0.50
-39.45mA
-26.38mA
-43.90mA
-0.40
-32.03mA
-22.06mA
-36.09mA
-0.30
-24.30mA
-16.63mA
-27.49mA
-0.20
-16.36mA
-11.10mA
-18.57mA
-0.10
-8.26mA
-5.55mA
-9.40mA
-0.00
3.97nA
7.41nA
12.45nA
0.10
8.11mA
5.36mA
9.30mA
0.20
15.76mA
10.38mA
18.18mA
|
102
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
0.30
22.98mA
15.05mA
26.64mA
0.40
29.76mA
19.40mA
34.68mA
0.50
36.11mA
23.42mA
42.32mA
0.60
42.04mA
27.11mA
49.54mA
0.70
47.55mA
30.50mA
56.36mA
0.80
52.65mA
33.58mA
62.78mA
0.90
57.35mA
36.36mA
68.80mA
1.00
61.64mA
38.84mA
74.42mA
1.10
65.54mA
41.04mA
79.65mA
1.20
69.06mA
42.96mA
84.48mA
1.30
72.18mA
44.61mA
88.92mA
1.40
74.93mA
45.99mA
92.97mA
1.50
77.31mA
47.12mA
96.63mA
1.60
79.32mA
48.01mA
99.91mA
1.70
80.95mA
48.68mA
0.10A
1.80
82.19mA
49.17mA
0.11A
1.90
83.08mA
49.54mA
0.11A
2.00
83.74mA
49.82mA
0.11A
2.10
84.23mA
50.06mA
0.11A
2.20
84.61mA
50.25mA
0.11A
2.30
84.93mA
50.42mA
0.11A
2.40
85.20mA
50.57mA
0.11A
2.50
85.43mA
50.70mA
0.11A
2.60
85.64mA
50.82mA
0.11A
2.70
85.83mA
50.93mA
0.11A
2.80
86.01mA
51.03mA
0.11A
2.90
86.17mA
51.13mA
0.11A
3.00
86.32mA
51.22mA
0.11A
3.10
86.47mA
51.31mA
0.11A
3.20
86.61mA
51.40mA
0.11A
3.30
86.75mA
51.50mA
0.11A
3.40
86.88mA
51.73mA
0.12A
3.50
87.01mA
52.32mA
0.12A
3.60
87.15mA
53.14mA
0.12A
3.70
87.30mA
54.01mA
0.12A
3.80
87.47mA
54.42mA
0.12A
3.90
87.77mA
52.16mA
0.12A
4.00
88.66mA
52.28mA
0.12A
4.10
90.00mA
52.42mA
0.12A
4.20
91.29mA
52.58mA
0.12A
4.30
89.03mA
52.77mA
0.12A
4.50
89.65mA
53.24mA
0.12A
4.70
90.63mA
53.86mA
0.12A
4.90
91.94mA
54.68mA
0.12A
Freescale Semiconductor
PRELIMINARY
103
Appendix B IBIS Model
5.10
93.62mA
55.72mA
0.12A
5.30
95.73mA
57.02mA
0.13A
5.50
98.29mA
58.58mA
0.13A
5.70
0.10A
60.42mA
0.13A
5.90
0.10A
62.54mA
0.14A
6.10
0.11A
64.92mA
0.14A
6.60
0.12A
71.81mA
0.15A
|
[Pullup]
| voltage
I(typ)
I(min)
I(max)
-3.30
0.22A
0.16A
0.25A
-3.10
0.21A
0.16A
0.24A
-2.90
0.20A
0.15A
0.23A
-2.70
0.19A
0.14A
0.22A
-2.50
0.18A
0.14A
0.21A
-2.30
0.17A
0.13A
0.20A
-2.10
0.16A
0.12A
0.18A
-1.90
0.15A
0.11A
0.17A
-1.70
0.14A
0.10A
0.16A
-1.50
0.12A
90.13mA
0.14A
-1.00
92.59mA
62.48mA
0.11A
-0.90
84.26mA
56.95mA
97.88mA
-0.80
75.03mA
54.36mA
87.19mA
-0.70
65.60mA
47.69mA
76.45mA
-0.60
56.28mA
40.63mA
66.08mA
-0.50
47.19mA
33.52mA
55.62mA
-0.40
37.96mA
26.49mA
44.89mA
-0.30
28.58mA
19.70mA
33.93mA
-0.20
19.09mA
13.03mA
22.76mA
-0.10
9.54mA
6.45mA
11.43mA
0.00
0.17uA
0.16uA
0.19uA
|
104
0.10
-9.23mA
-6.17mA
-11.15mA
0.20
-17.95mA
-11.99mA
-21.75mA
0.30
-26.16mA
-17.46mA
-31.79mA
0.40
-33.86mA
-22.57mA
-41.28mA
0.50
-41.07mA
-27.35mA
-50.24mA
0.60
-47.79mA
-31.77mA
-58.67mA
0.70
-54.04mA
-35.86mA
-66.58mA
0.80
-59.82mA
-39.62mA
-73.98mA
0.90
-65.13mA
-43.05mA
-80.88mA
1.00
-69.99mA
-46.15mA
-87.29mA
1.10
-74.41mA
-48.92mA
-93.21mA
1.20
-78.38mA
-51.38mA
-98.65mA
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
1.30
-81.93mA
-53.52mA
-0.10A
1.40
-85.05mA
-55.36mA
-0.11A
1.50
-87.75mA
-56.88mA
-0.11A
1.60
-90.05mA
-58.12mA
-0.12A
1.70
-91.96mA
-59.09mA
-0.12A
1.80
-93.52mA
-59.84mA
-0.12A
1.90
-94.78mA
-60.43mA
-0.12A
2.00
-95.80mA
-60.92mA
-0.13A
2.10
-96.66mA
-61.35mA
-0.13A
2.20
-97.39mA
-61.72mA
-0.13A
2.30
-98.03mA
-62.06mA
-0.13A
2.40
-98.58mA
-62.37mA
-0.13A
2.50
-99.08mA
-62.65mA
-0.13A
2.60
-99.52mA
-62.91mA
-0.13A
2.70
-99.92mA
-63.15mA
-0.13A
2.80
-0.10A
-63.37mA
-0.13A
2.90
-0.10A
-63.58mA
-0.13A
3.00
-0.10A
-63.78mA
-0.13A
3.10
-0.10A
-63.96mA
-0.14A
3.20
-0.10A
-64.14mA
-0.14A
3.30
-0.10A
-64.33mA
-0.14A
3.40
-0.10A
-64.95mA
-0.14A
3.50
-0.10A
-72.61mA
-0.14A
3.60
-0.10A
-0.17A
-0.14A
3.70
-0.10A
-0.97A
-0.14A
3.80
-0.10A
-2.72A
-0.14A
3.90
-0.11A
-4.50A
-0.14A
4.00
-0.12A
-6.28A
-0.14A
4.10
-0.34A
-8.06A
-0.14A
4.20
-1.90A
-9.85A
-0.14A
4.30
-3.94A
-11.62A
-0.15A
4.50
-8.02A
-15.19A
-1.20A
4.70
-12.10A
-18.75A
-5.43A
4.90
-16.18A
-22.31A
-9.67A
5.10
-20.27A
-25.88A
-13.90A
5.30
-24.35A
-29.44A
-18.14A
5.50
-28.43A
-33.00A
-22.38A
5.70
-32.51A
-36.56A
-26.62A
5.90
-36.60A
-40.13A
-30.86A
6.10
-40.68A
-43.69A
-35.09A
6.60
-50.89A
-52.59A
-45.69A
I(typ)
I(min)
I(max)
|
[GND_clamp]
| voltage
Freescale Semiconductor
PRELIMINARY
105
Appendix B IBIS Model
|
-3.30
-50.75A
-47.17A
-51.87A
-3.20
-48.72A
-45.39A
-49.75A
-3.10
-46.68A
-43.61A
-47.63A
-3.00
-44.64A
-41.83A
-45.52A
-2.90
-42.60A
-40.05A
-43.40A
-2.80
-40.56A
-38.27A
-41.29A
-2.70
-38.52A
-36.49A
-39.17A
-2.60
-36.48A
-34.71A
-37.05A
-2.50
-34.44A
-32.93A
-34.94A
-2.40
-32.40A
-31.15A
-32.82A
-2.30
-30.36A
-29.37A
-30.70A
-2.20
-28.32A
-27.59A
-28.58A
-2.10
-26.28A
-25.81A
-26.47A
-2.00
-24.24A
-24.03A
-24.35A
-1.90
-22.20A
-22.25A
-22.23A
-1.80
-20.16A
-20.47A
-20.11A
-1.70
-18.12A
-18.68A
-18.00A
-1.60
-16.08A
-16.90A
-15.88A
-1.50
-14.04A
-15.12A
-13.76A
-1.40
-12.00A
-13.34A
-11.64A
-1.30
-9.96A
-11.56A
-9.53A
-1.20
-7.92A
-9.78A
-7.41A
-1.10
-5.88A
-8.00A
-5.29A
-1.00
-3.84A
-6.22A
-3.18A
-0.90
-1.80A
-4.44A
-1.07A
-0.80
-0.23A
-2.65A
-71.53mA
-0.70
-13.26mA
-0.90A
-13.93mA
-0.60
-2.23mA
-0.10A
-6.08mA
-0.50
-0.34mA
-7.99mA
-1.62mA
-0.40
-28.68uA
-0.48mA
-0.18mA
-0.30
-1.65uA
-27.22uA
-10.18uA
-0.20
-0.15uA
-1.61uA
-0.42uA
-0.10
-86.50nA
-0.17uA
-0.11uA
-0.00
-76.61nA
-77.36nA
-91.73nA
0.10
-68.52nA
-64.82nA
-83.30nA
0.20
-60.47nA
-56.49nA
-75.01nA
0.30
-52.43nA
-48.39nA
-66.73nA
0.40
-44.39nA
-40.30nA
-58.46nA
0.50
-36.35nA
-32.21nA
-50.19nA
0.60
-28.31nA
-24.12nA
-41.93nA
0.70
-20.27nA
-16.03nA
-33.68nA
0.80
-12.24nA
-7.94nA
-25.42nA
0.90
-4.20nA
0.15nA
-17.17nA
106
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
1.00
3.83nA
8.23nA
-8.92nA
1.10
11.86nA
16.32nA
-0.67nA
1.20
19.89nA
24.41nA
7.58nA
1.30
27.92nA
32.50nA
15.84nA
1.40
35.95nA
40.59nA
24.10nA
1.50
43.98nA
48.68nA
32.36nA
1.60
52.00nA
56.77nA
40.64nA
1.70
60.02nA
64.85nA
48.92nA
1.80
68.04nA
72.94nA
57.21nA
1.90
76.05nA
81.03nA
65.52nA
2.00
84.05nA
89.12nA
73.85nA
2.10
92.04nA
97.20nA
82.20nA
2.20
100.00nA
0.11uA
90.59nA
2.30
0.11uA
0.11uA
99.01nA
2.40
0.12uA
0.12uA
0.11uA
2.50
0.12uA
0.12uA
0.12uA
2.60
0.13uA
0.13uA
0.12uA
2.70
0.13uA
0.13uA
0.13uA
2.80
0.14uA
0.13uA
0.14uA
2.90
0.14uA
0.14uA
0.15uA
3.00
0.15uA
0.15uA
0.15uA
3.10
0.15uA
0.17uA
0.16uA
3.20
0.15uA
0.56uA
0.16uA
3.30
0.16uA
0.19uA
0.17uA
|
[POWER_clamp]
| voltage
I(typ)
I(min)
I(max)
|
-3.30
0.37uA
0.37uA
0.40uA
-3.20
0.37uA
0.36uA
0.39uA
-3.10
0.36uA
0.36uA
0.39uA
-3.00
0.35uA
0.35uA
0.38uA
-2.90
0.35uA
0.34uA
0.37uA
-2.80
0.34uA
0.34uA
0.37uA
-2.70
0.33uA
0.33uA
0.36uA
-2.60
0.33uA
0.33uA
0.36uA
-2.50
0.32uA
0.32uA
0.35uA
-2.40
0.32uA
0.31uA
0.34uA
-2.30
0.31uA
0.31uA
0.34uA
-2.20
0.30uA
0.30uA
0.33uA
-2.10
0.30uA
0.29uA
0.32uA
-2.00
0.29uA
0.29uA
0.32uA
-1.90
0.28uA
0.28uA
0.31uA
-1.80
0.28uA
0.28uA
0.30uA
Freescale Semiconductor
PRELIMINARY
107
Appendix B IBIS Model
-1.70
0.27uA
0.27uA
0.30uA
-1.60
0.27uA
0.26uA
0.29uA
-1.50
0.26uA
0.26uA
0.29uA
-1.40
0.25uA
0.25uA
0.28uA
-1.30
0.25uA
0.25uA
0.27uA
-1.20
0.24uA
0.24uA
0.27uA
-1.10
0.24uA
0.23uA
0.26uA
-1.00
0.23uA
0.23uA
0.25uA
-0.90
0.22uA
0.22uA
0.25uA
-0.80
0.22uA
0.22uA
0.24uA
-0.70
0.21uA
0.21uA
0.24uA
-0.60
0.21uA
0.20uA
0.23uA
-0.50
0.20uA
0.20uA
0.22uA
-0.40
0.20uA
0.19uA
0.22uA
-0.30
0.19uA
0.19uA
0.21uA
-0.20
0.48mA
0.56uA
0.72uA
-0.10
0.16uA
0.17uA
0.18uA
0.00
0.16uA
0.15uA
0.18uA
|
[Ramp]
| variable
typ
min
max
dV/dt_r
1.54/2.19n
1.20/2.87n
1.77/2.14n
dV/dt_f
1.52/3.15n
1.15/4.45n
1.73/3.01n
V(min)
V(max)
R_load = 50.00
|
[Rising Waveform]
R_fixture = 50.00
V_fixture = 0.000
V_fixture_min = 0.000
V_fixture_max = 0.000
L_fixture = 0.000H
C_fixture = 0.000F
| time
V(typ)
|
0.000S
108
0.70uV
0.93uV
0.69uV
0.20nS
0.46uV
0.77uV
0.40nS
-5.77uV
-1.75uV
11.67uV
0.60nS
-0.27mV
-5.10uV
-2.79mV
0.80nS
-2.96mV
26.03uV
-6.12mV
1.00nS
-3.62mV
-5.61uV
32.64mV
1.20nS
19.35mV
-0.80mV
81.12mV
1.40nS
46.31mV
-3.19mV
0.11V
1.60nS
79.98mV
-6.88mV
0.16V
PRELIMINARY
0.000V
Freescale Semiconductor
Appendix B IBIS Model
1.80nS
0.12V
-0.22mV
0.21V
2.00nS
0.16V
21.89mV
0.27V
2.20nS
0.20V
48.68mV
0.33V
2.40nS
0.26V
76.62mV
0.41V
2.60nS
0.32V
0.11V
0.49V
2.80nS
0.42V
0.16V
0.61V
3.00nS
0.51V
0.20V
0.73V
3.20nS
0.58V
0.24V
0.82V
3.40nS
0.71V
0.30V
0.99V
3.60nS
0.85V
0.36V
1.17V
3.80nS
1.01V
0.45V
1.36V
4.00nS
1.18V
0.54V
1.56V
4.20nS
1.38V
0.67V
1.81V
4.40nS
1.57V
0.81V
2.03V
4.60nS
1.69V
0.89V
2.16V
4.80nS
1.79V
0.96V
2.27V
5.00nS
1.91V
1.06V
2.40V
5.20nS
2.03V
1.15V
2.52V
5.40nS
2.14V
1.26V
2.61V
5.60nS
2.24V
1.35V
2.70V
5.80nS
2.28V
1.40V
2.74V
6.00nS
2.31V
1.45V
2.77V
6.20nS
2.36V
1.51V
2.80V
6.40nS
2.39V
1.56V
2.83V
6.60nS
2.41V
1.61V
2.85V
6.80nS
2.43V
1.66V
2.86V
7.00nS
2.45V
1.70V
2.87V
7.20nS
2.46V
1.74V
2.88V
7.40nS
2.48V
1.78V
2.89V
7.60nS
2.49V
1.82V
2.90V
7.80nS
2.50V
1.84V
2.91V
8.00nS
2.51V
1.86V
2.91V
8.20nS
2.52V
1.88V
2.92V
8.40nS
2.52V
1.90V
2.92V
8.60nS
2.53V
1.92V
2.93V
8.80nS
2.54V
1.93V
2.93V
9.00nS
2.54V
1.95V
2.93V
9.20nS
2.55V
1.96V
2.94V
9.40nS
2.55V
1.97V
2.94V
9.60nS
2.56V
1.99V
2.94V
9.80nS
2.56V
2.00V
2.95V
10.00nS
2.57V
2.00V
2.95V
|
[Rising Waveform]
Freescale Semiconductor
PRELIMINARY
109
Appendix B IBIS Model
R_fixture = 50.00
V_fixture = 3.30
V_fixture_min = 3.00
V_fixture_max = 3.60
L_fixture = 0.000H
C_fixture = 0.000F
| time
V(typ)
V(min)
V(max)
|
0.000S
110
0.76V
1.03V
0.72V
0.20nS
0.76V
1.03V
0.72V
0.40nS
0.76V
1.03V
0.72V
0.60nS
0.76V
1.03V
0.72V
0.80nS
0.77V
1.03V
0.73V
1.00nS
0.81V
1.03V
0.82V
1.20nS
0.90V
1.03V
0.93V
1.40nS
0.98V
1.04V
1.02V
1.60nS
1.10V
1.11V
1.13V
1.80nS
1.22V
1.21V
1.26V
2.00nS
1.36V
1.33V
1.42V
2.20nS
1.53V
1.46V
1.58V
2.40nS
1.72V
1.60V
1.80V
2.60nS
1.93V
1.75V
2.04V
2.80nS
2.23V
1.97V
2.36V
3.00nS
2.48V
2.16V
2.62V
3.20nS
2.66V
2.30V
2.82V
3.40nS
2.85V
2.49V
3.04V
3.60nS
2.97V
2.63V
3.19V
3.80nS
3.09V
2.73V
3.29V
4.00nS
3.14V
2.83V
3.36V
4.20nS
3.19V
2.89V
3.42V
4.40nS
3.23V
2.94V
3.47V
4.60nS
3.25V
2.96V
3.50V
4.80nS
3.27V
2.97V
3.52V
5.00nS
3.28V
2.98V
3.54V
5.20nS
3.29V
2.99V
3.56V
5.40nS
3.29V
2.99V
3.57V
5.60nS
3.30V
3.00V
3.58V
5.80nS
3.30V
3.00V
3.59V
6.00nS
3.30V
3.00V
3.59V
6.20nS
3.30V
3.00V
3.60V
6.40nS
3.30V
3.00V
3.60V
6.60nS
3.30V
3.00V
3.60V
6.80nS
3.30V
3.00V
3.60V
7.00nS
3.30V
3.00V
3.60V
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
7.20nS
3.30V
3.00V
3.60V
7.40nS
3.30V
3.00V
3.60V
7.60nS
3.30V
3.00V
3.60V
7.80nS
3.30V
3.00V
3.60V
8.00nS
3.30V
3.00V
3.60V
8.20nS
3.30V
3.00V
3.60V
8.40nS
3.30V
3.00V
3.60V
8.60nS
3.30V
3.00V
3.60V
8.80nS
3.30V
3.00V
3.60V
9.00nS
3.30V
3.00V
3.60V
9.20nS
3.30V
3.00V
3.60V
9.40nS
3.30V
3.00V
3.60V
9.60nS
3.30V
3.00V
3.60V
9.80nS
3.30V
3.00V
3.60V
10.00nS
3.30V
3.00V
3.60V
V(typ)
V(min)
V(max)
2.62V
2.12V
2.99V
0.20nS
2.62V
2.12V
2.99V
0.40nS
2.62V
2.12V
2.99V
0.60nS
2.62V
2.12V
2.96V
0.80nS
2.60V
2.12V
2.85V
1.00nS
2.50V
2.12V
2.72V
1.20nS
2.37V
2.11V
2.59V
1.40nS
2.29V
2.09V
2.50V
1.60nS
2.17V
2.04V
2.36V
1.80nS
2.04V
1.96V
2.20V
2.00nS
1.89V
1.85V
2.00V
2.20nS
1.71V
1.74V
1.75V
2.40nS
1.50V
1.63V
1.48V
2.60nS
1.28V
1.50V
1.24V
2.80nS
1.01V
1.33V
1.01V
3.00nS
0.82V
1.17V
0.82V
3.20nS
0.72V
1.04V
0.75V
3.40nS
0.61V
0.87V
0.65V
3.60nS
0.51V
0.72V
0.57V
|
[Falling Waveform]
R_fixture = 50.00
V_fixture = 0.000
V_fixture_min = 0.000
V_fixture_max = 0.000
L_fixture = 0.000H
C_fixture = 0.000F
| time
|
0.000S
Freescale Semiconductor
PRELIMINARY
111
Appendix B IBIS Model
3.80nS
0.44V
0.60V
0.50V
4.00nS
0.38V
0.49V
0.44V
4.20nS
0.32V
0.40V
0.38V
4.40nS
0.26V
0.32V
0.32V
4.60nS
0.23V
0.28V
0.29V
4.80nS
0.21V
0.25V
0.26V
5.00nS
0.17V
0.21V
0.23V
5.20nS
0.15V
0.18V
0.20V
5.40nS
0.12V
0.14V
0.17V
5.60nS
93.14mV
0.11V
0.14V
5.80nS
80.86mV
94.78mV
0.12V
6.00nS
68.57mV
80.67mV
0.11V
6.20nS
55.24mV
65.96mV
90.13mV
6.40nS
43.92mV
51.39mV
74.96mV
6.60nS
33.33mV
40.71mV
61.03mV
6.80nS
25.91mV
31.19mV
50.31mV
7.00nS
18.81mV
22.83mV
39.65mV
7.20nS
13.52mV
17.13mV
31.61mV
7.40nS
8.40mV
10.61mV
22.62mV
7.60nS
4.73mV
6.73mV
15.75mV
7.80nS
3.46mV
4.67mV
12.43mV
8.00nS
2.19mV
3.16mV
9.14mV
8.20nS
1.26mV
2.23mV
6.37mV
8.40nS
0.84mV
1.32mV
4.12mV
8.60nS
0.49mV
0.95mV
2.29mV
8.80nS
0.41mV
0.74mV
1.55mV
9.00nS
0.35mV
0.58mV
0.81mV
9.20nS
0.31mV
0.51mV
0.53mV
9.40nS
0.28mV
0.45mV
0.39mV
9.60nS
0.24mV
0.40mV
0.27mV
9.80nS
0.22mV
0.36mV
0.24mV
10.00nS
0.20mV
0.32mV
0.21mV
|
[Falling Waveform]
R_fixture = 50.00
V_fixture = 3.30
V_fixture_min = 3.00
V_fixture_max = 3.60
L_fixture = 0.000H
C_fixture = 0.000F
| time
V(typ)
V(min)
V(max)
3.30V
3.00V
3.60V
3.30V
3.00V
3.60V
|
0.000S
0.20nS
112
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
0.40nS
3.30V
3.00V
3.60V
0.60nS
3.30V
3.00V
3.59V
0.80nS
3.30V
3.00V
3.52V
1.00nS
3.25V
3.00V
3.44V
1.20nS
3.18V
3.00V
3.37V
1.40nS
3.14V
3.00V
3.32V
1.60nS
3.09V
3.00V
3.24V
1.80nS
3.03V
2.97V
3.16V
2.00nS
2.96V
2.92V
3.07V
2.20nS
2.88V
2.88V
2.98V
2.40nS
2.80V
2.84V
2.88V
2.60nS
2.72V
2.80V
2.77V
2.80nS
2.60V
2.74V
2.64V
3.00nS
2.51V
2.68V
2.54V
3.20nS
2.44V
2.64V
2.46V
3.40nS
2.34V
2.58V
2.34V
3.60nS
2.25V
2.52V
2.22V
3.80nS
2.15V
2.46V
2.08V
4.00nS
2.05V
2.39V
1.92V
4.20nS
1.93V
2.32V
1.74V
4.40nS
1.81V
2.24V
1.58V
4.60nS
1.73V
2.19V
1.50V
4.80nS
1.65V
2.15V
1.42V
5.00nS
1.53V
2.09V
1.34V
5.20nS
1.43V
2.04V
1.26V
5.40nS
1.32V
1.97V
1.18V
5.60nS
1.22V
1.91V
1.11V
5.80nS
1.18V
1.87V
1.07V
6.00nS
1.13V
1.84V
1.03V
6.20nS
1.08V
1.79V
0.99V
6.40nS
1.03V
1.75V
0.95V
6.60nS
0.99V
1.70V
0.92V
6.80nS
0.96V
1.66V
0.89V
7.00nS
0.93V
1.63V
0.87V
7.20nS
0.90V
1.59V
0.84V
7.40nS
0.87V
1.53V
0.82V
7.60nS
0.84V
1.47V
0.80V
7.80nS
0.83V
1.44V
0.78V
8.00nS
0.82V
1.40V
0.78V
8.20nS
0.81V
1.35V
0.76V
8.40nS
0.80V
1.30V
0.75V
8.60nS
0.79V
1.26V
0.75V
8.80nS
0.78V
1.23V
0.74V
9.00nS
0.78V
1.19V
0.73V
Freescale Semiconductor
PRELIMINARY
113
Appendix B IBIS Model
9.20nS
0.78V
1.17V
0.73V
9.40nS
0.77V
1.14V
0.73V
9.60nS
0.77V
1.12V
0.72V
9.80nS
0.77V
1.10V
0.72V
10.00nS
0.77V
1.08V
0.72V
|
| End [Model] prt24dgz
|
|************************************************************************
|
Model pdusdgz
|************************************************************************
|
[Model]
pdusdgz
Model_type
Input
Polarity
Non-Inverting
Vinl =
0.000V
Vinh =
3.30V
C_comp
5.00pF
5.00pF
5.00pF
|
|
[Temperature Range]
25.00
0.12k
0.000
[Pullup Reference]
3.30V
3.00V
3.60V
[Pulldown Reference]
0.000V
0.000V
0.000V
[POWER Clamp Reference]
5.00V
4.50V
5.50V
[GND Clamp Reference]
0.000V
0.000V
0.000V
[GND_clamp]
| voltage
I(typ)
I(min)
I(max)
-5.00
-64.63A
-59.13A
-66.41A
-4.80
-61.55A
-56.41A
-63.21A
-4.60
-58.47A
-53.69A
-60.01A
-4.40
-55.39A
-50.97A
-56.81A
-4.20
-52.31A
-48.25A
-53.61A
-4.00
-49.23A
-45.53A
-50.41A
-3.80
-46.15A
-42.81A
-47.21A
-3.60
-43.07A
-40.09A
-44.01A
-3.40
-39.99A
-37.37A
-40.81A
-3.20
-36.91A
-34.65A
-37.61A
-3.00
-33.82A
-31.94A
-34.41A
-2.80
-30.73A
-29.22A
-31.22A
-2.60
-27.64A
-26.51A
-28.02A
-2.40
-24.56A
-23.79A
-24.82A
-2.20
-21.47A
-21.08A
-21.62A
-2.00
-18.38A
-18.36A
-18.42A
|
114
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
-1.80
-15.29A
-15.64A
-15.22A
-1.60
-12.20A
-12.93A
-12.03A
-1.40
-9.12A
-10.21A
-8.83A
-1.20
-6.03A
-7.50A
-5.63A
-1.00
-2.94A
-4.78A
-2.43A
-0.80
-0.20A
-2.07A
-64.17mA
-0.60
-1.85mA
-96.40mA
-4.85mA
-0.40
-83.24uA
-0.50mA
-0.23mA
-0.20
-60.52uA
-36.82uA
-86.29uA
-0.00
-60.40uA
-35.33uA
-85.95uA
0.20
-60.32uA
-35.27uA
-85.85uA
0.40
-60.23uA
-35.20uA
-85.73uA
0.60
-60.11uA
-35.13uA
-85.57uA
0.80
-59.96uA
-35.03uA
-85.37uA
1.00
-59.74uA
-34.91uA
-85.08uA
1.20
-59.32uA
-34.50uA
-84.56uA
1.40
-58.35uA
-33.59uA
-83.44uA
1.60
-56.47uA
-31.92uA
-81.36uA
1.80
-53.57uA
-29.25uA
-78.20uA
2.00
-49.55uA
-7.60uA
-73.89uA
2.20
-43.70uA
-16.78nA
-68.43uA
2.40
-3.73uA
0.10uA
-61.70uA
2.60
0.10uA
0.11uA
-51.99uA
2.80
0.12uA
0.12uA
-2.43uA
3.00
0.13uA
0.13uA
0.13uA
3.20
0.14uA
0.20uA
0.14uA
3.40
0.15uA
0.15uA
0.15uA
3.60
0.16uA
96.30nA
0.16uA
3.80
0.17uA
43.50nA
0.17uA
4.00
0.18uA
-9.30nA
0.18uA
4.20
0.18uA
-62.10nA
0.19uA
4.40
0.19uA
-0.11uA
0.20uA
4.60
0.20uA
-0.17uA
0.21uA
4.80
0.21uA
-0.22uA
0.22uA
5.00
0.22uA
-0.27uA
0.23uA
|
[POWER_clamp]
| voltage
I(typ)
I(min)
I(max)
|
-5.00
0.61uA
0.59uA
0.65uA
-4.90
0.60uA
0.58uA
0.65uA
-4.80
0.59uA
0.58uA
0.64uA
-4.70
0.59uA
0.57uA
0.63uA
-4.60
0.58uA
0.56uA
0.63uA
Freescale Semiconductor
PRELIMINARY
115
Appendix B IBIS Model
-4.50
0.57uA
0.56uA
0.62uA
-4.40
0.56uA
0.55uA
0.61uA
-4.30
0.56uA
0.54uA
0.60uA
-4.20
0.55uA
0.54uA
0.60uA
-4.10
0.54uA
0.53uA
0.59uA
-4.00
0.54uA
0.52uA
0.58uA
-3.90
0.53uA
0.52uA
0.58uA
-3.80
0.52uA
0.51uA
0.57uA
-3.70
0.52uA
0.50uA
0.56uA
-3.60
0.51uA
0.50uA
0.56uA
-3.50
0.50uA
0.49uA
0.55uA
-3.40
0.50uA
0.48uA
0.54uA
-3.30
0.49uA
0.48uA
0.53uA
-3.20
0.48uA
0.47uA
0.53uA
-3.10
0.48uA
0.46uA
0.52uA
-3.00
0.47uA
0.46uA
0.51uA
-2.90
0.46uA
0.45uA
0.51uA
-2.80
0.46uA
0.44uA
0.50uA
-2.70
0.45uA
0.44uA
0.49uA
-2.60
0.44uA
0.43uA
0.49uA
-2.50
0.44uA
0.42uA
0.48uA
-2.40
0.43uA
0.41uA
0.47uA
-2.30
0.42uA
0.41uA
0.46uA
-2.20
0.42uA
0.40uA
0.46uA
-2.10
0.41uA
0.39uA
0.45uA
-2.00
0.40uA
0.39uA
0.44uA
-1.90
0.39uA
0.38uA
0.44uA
-1.80
0.39uA
0.37uA
0.43uA
-1.70
0.38uA
0.37uA
0.42uA
-1.60
0.37uA
0.36uA
0.42uA
-1.50
0.37uA
0.35uA
0.41uA
-1.40
0.36uA
0.35uA
0.40uA
-1.30
0.35uA
0.34uA
0.39uA
-1.20
0.35uA
0.33uA
0.39uA
-1.10
0.34uA
0.33uA
0.38uA
-1.00
0.33uA
0.32uA
0.37uA
-0.90
0.33uA
0.31uA
0.37uA
-0.80
0.32uA
0.31uA
0.36uA
-0.70
0.31uA
0.30uA
0.35uA
-0.60
0.31uA
0.29uA
0.35uA
-0.50
0.30uA
0.29uA
0.34uA
-0.40
0.29uA
0.28uA
0.33uA
-0.30
0.29uA
0.27uA
0.32uA
-0.20
0.28uA
0.27uA
0.32uA
116
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
-0.10
0.27uA
0.26uA
0.31uA
0.00
0.27uA
0.25uA
0.30uA
|
| End [Model] pdusdgz
|
|************************************************************************
|
Model pdddgz
|************************************************************************
|
[Model]
pdddgz
Model_type
Input
Polarity
Non-Inverting
Vinl =
0.000V
Vinh =
3.30V
C_comp
5.00pF
5.00pF
5.00pF
|
|
[Temperature Range]
25.00
0.12k
0.000
[Pullup Reference]
3.30V
3.00V
3.60V
[Pulldown Reference]
0.000V
0.000V
0.000V
[POWER Clamp Reference]
5.00V
4.50V
5.50V
[GND Clamp Reference]
0.000V
0.000V
0.000V
[GND_clamp]
| voltage
I(typ)
I(min)
I(max)
-5.00
-64.63A
-59.13A
-66.41A
-4.80
-61.55A
-56.41A
-63.21A
-4.60
-58.47A
-53.69A
-60.01A
-4.40
-55.39A
-50.97A
-56.81A
-4.20
-52.31A
-48.25A
-53.61A
-4.00
-49.23A
-45.53A
-50.41A
-3.80
-46.15A
-42.81A
-47.21A
-3.60
-43.07A
-40.09A
-44.01A
-3.40
-39.99A
-37.37A
-40.81A
-3.20
-36.91A
-34.65A
-37.61A
-3.00
-33.82A
-31.94A
-34.41A
-2.80
-30.73A
-29.22A
-31.22A
-2.60
-27.64A
-26.51A
-28.02A
-2.40
-24.56A
-23.79A
-24.82A
-2.20
-21.47A
-21.08A
-21.62A
-2.00
-18.38A
-18.36A
-18.42A
-1.80
-15.29A
-15.64A
-15.22A
-1.60
-12.20A
-12.93A
-12.03A
-1.40
-9.12A
-10.21A
-8.83A
|
Freescale Semiconductor
PRELIMINARY
117
Appendix B IBIS Model
-1.20
-6.03A
-7.50A
-5.63A
-1.00
-2.94A
-4.78A
-2.43A
-0.80
-0.20A
-2.07A
-64.21mA
-0.60
-1.89mA
-0.40
-85.69uA
-0.50mA
-0.24mA
-0.20
-27.91uA
-14.61uA
-42.88uA
-0.00
-87.50nA
-88.83nA
-0.10uA
0.20
18.71uA
7.31uA
32.27uA
0.40
29.18uA
10.24uA
54.12uA
0.60
32.49uA
10.66uA
65.78uA
0.80
33.06uA
10.78uA
69.33uA
1.00
33.29uA
10.85uA
70.16uA
1.20
33.44uA
10.91uA
70.54uA
1.40
33.56uA
10.96uA
70.78uA
1.60
33.66uA
11.01uA
70.98uA
1.80
33.76uA
11.06uA
71.15uA
2.00
33.85uA
11.10uA
71.30uA
2.20
33.94uA
11.12uA
71.44uA
2.40
33.99uA
11.13uA
71.59uA
2.60
34.01uA
11.14uA
71.74uA
2.80
34.02uA
11.15uA
71.82uA
3.00
34.03uA
11.16uA
71.84uA
3.20
34.04uA
11.25uA
71.85uA
3.40
34.06uA
11.17uA
71.87uA
3.60
34.08uA
11.09uA
71.89uA
3.80
34.10uA
11.01uA
71.91uA
4.00
34.12uA
10.93uA
71.93uA
4.20
34.14uA
10.85uA
71.95uA
4.40
34.16uA
10.77uA
71.97uA
4.60
34.18uA
10.69uA
71.99uA
4.80
34.20uA
10.61uA
72.01uA
5.00
34.22uA
10.53uA
72.03uA
I(typ)
I(min)
I(max)
-5.00
48.19uA
16.29uA
95.53uA
-4.90
47.87uA
16.17uA
95.03uA
-4.80
47.55uA
16.05uA
94.53uA
-4.70
47.23uA
15.93uA
94.03uA
-4.60
46.91uA
15.81uA
93.53uA
-4.50
46.59uA
15.69uA
93.03uA
-4.40
46.27uA
15.57uA
92.53uA
-4.30
45.95uA
15.45uA
92.03uA
-96.41mA
-4.91mA
|
[POWER_clamp]
| voltage
|
118
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
-4.20
45.63uA
15.33uA
91.53uA
-4.10
45.31uA
15.21uA
91.03uA
-4.00
44.99uA
15.09uA
90.53uA
-3.90
44.67uA
14.97uA
90.03uA
-3.80
44.35uA
14.85uA
89.53uA
-3.70
44.03uA
14.73uA
89.03uA
-3.60
43.71uA
14.61uA
88.53uA
-3.50
43.39uA
14.49uA
88.03uA
-3.40
43.07uA
14.37uA
87.53uA
-3.30
42.75uA
14.25uA
87.03uA
-3.20
42.43uA
14.13uA
86.53uA
-3.10
42.11uA
14.01uA
86.03uA
-3.00
41.79uA
13.89uA
85.53uA
-2.90
41.47uA
13.77uA
85.03uA
-2.80
41.15uA
13.65uA
84.53uA
-2.70
40.83uA
13.53uA
84.03uA
-2.60
40.51uA
13.41uA
83.53uA
-2.50
40.19uA
13.29uA
83.03uA
-2.40
39.87uA
13.17uA
82.53uA
-2.30
39.55uA
13.05uA
82.03uA
-2.20
39.23uA
12.93uA
81.53uA
-2.10
38.91uA
12.81uA
81.03uA
-2.00
38.59uA
12.69uA
80.53uA
-1.90
38.27uA
12.57uA
80.03uA
-1.80
37.95uA
12.45uA
79.53uA
-1.70
37.63uA
12.33uA
79.03uA
-1.60
37.31uA
12.22uA
78.53uA
-1.50
36.99uA
12.11uA
78.03uA
-1.40
36.68uA
12.01uA
77.53uA
-1.30
36.38uA
11.92uA
77.03uA
-1.20
36.11uA
11.84uA
76.53uA
-1.10
35.86uA
11.76uA
76.03uA
-1.00
35.63uA
11.69uA
75.53uA
-0.90
35.41uA
11.63uA
75.06uA
-0.80
35.22uA
11.57uA
74.63uA
-0.70
35.05uA
11.52uA
74.24uA
-0.60
34.90uA
11.48uA
73.89uA
-0.50
34.77uA
11.44uA
73.58uA
-0.40
34.65uA
11.41uA
73.30uA
-0.30
34.55uA
11.38uA
73.06uA
-0.20
34.47uA
11.35uA
72.86uA
-0.10
34.40uA
11.33uA
72.68uA
0.00
34.34uA
11.31uA
72.54uA
|
Freescale Semiconductor
PRELIMINARY
119
Appendix B IBIS Model
| End [Model] pdddgz
|
|************************************************************************
|
Model pdudgz
|************************************************************************
|
[Model]
pdudgz
Model_type
Input
Polarity
Non-Inverting
Vinl =
0.000V
Vinh =
3.30V
C_comp
5.00pF
5.00pF
5.00pF
|
|
[Temperature Range]
25.00
0.12k
0.000
[Pullup Reference]
3.30V
3.00V
3.60V
[Pulldown Reference]
0.000V
0.000V
0.000V
[POWER Clamp Reference]
5.00V
4.50V
5.50V
[GND Clamp Reference]
0.000V
0.000V
0.000V
[GND_clamp]
| voltage
I(typ)
I(min)
I(max)
-5.00
-64.63A
-59.13A
-66.41A
-4.80
-61.55A
-56.41A
-63.21A
-4.60
-58.47A
-53.69A
-60.01A
-4.40
-55.39A
-50.97A
-56.81A
-4.20
-52.31A
-48.25A
-53.61A
-4.00
-49.23A
-45.53A
-50.41A
-3.80
-46.15A
-42.81A
-47.21A
-3.60
-43.07A
-40.09A
-44.01A
-3.40
-39.99A
-37.37A
-40.81A
-3.20
-36.91A
-34.65A
-37.61A
-3.00
-33.82A
-31.94A
-34.41A
-2.80
-30.73A
-29.22A
-31.22A
-2.60
-27.64A
-26.51A
-28.02A
-2.40
-24.56A
-23.79A
-24.82A
-2.20
-21.47A
-21.08A
-21.62A
-2.00
-18.38A
-18.36A
-18.42A
-1.80
-15.29A
-15.64A
-15.22A
-1.60
-12.20A
-12.93A
-12.03A
-1.40
-9.12A
-10.21A
-8.83A
-1.20
-6.03A
-7.50A
-5.63A
-1.00
-2.94A
-4.78A
-2.43A
-0.80
-0.20A
-2.07A
-64.17mA
|
120
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
-0.60
-1.85mA
-96.40mA
-4.85mA
-0.40
-83.24uA
-0.50mA
-0.23mA
-0.20
-60.52uA
-36.82uA
-86.29uA
-0.00
-60.40uA
-35.33uA
-85.95uA
0.20
-60.32uA
-35.27uA
-85.85uA
0.40
-60.23uA
-35.20uA
-85.73uA
0.60
-60.11uA
-35.13uA
-85.57uA
0.80
-59.96uA
-35.03uA
-85.37uA
1.00
-59.74uA
-34.87uA
-85.08uA
1.20
-59.32uA
-34.50uA
-84.56uA
1.40
-58.35uA
-33.59uA
-83.44uA
1.60
-56.47uA
-31.92uA
-81.36uA
1.80
-53.57uA
-29.25uA
-78.20uA
2.00
-49.55uA
-7.60uA
-73.89uA
2.20
-43.70uA
-16.78nA
-68.43uA
2.40
-3.73uA
0.10uA
-61.70uA
2.60
0.10uA
0.11uA
-51.99uA
2.80
0.12uA
0.12uA
-2.43uA
3.00
0.13uA
0.13uA
0.13uA
3.20
0.14uA
0.20uA
0.14uA
3.40
0.15uA
0.15uA
0.15uA
3.60
0.16uA
96.30nA
0.16uA
3.80
0.17uA
43.50nA
0.17uA
4.00
0.18uA
-9.30nA
0.18uA
4.20
0.18uA
-62.10nA
0.19uA
4.40
0.19uA
-0.11uA
0.20uA
4.60
0.20uA
-0.17uA
0.21uA
4.80
0.21uA
-0.22uA
0.22uA
5.00
0.22uA
-0.27uA
0.23uA
|
[POWER_clamp]
| voltage
I(typ)
I(min)
I(max)
|
-5.00
0.61uA
0.59uA
0.65uA
-4.90
0.60uA
0.58uA
0.65uA
-4.80
0.59uA
0.58uA
0.64uA
-4.70
0.59uA
0.57uA
0.63uA
-4.60
0.58uA
0.56uA
0.63uA
-4.50
0.57uA
0.56uA
0.62uA
-4.40
0.56uA
0.55uA
0.61uA
-4.30
0.56uA
0.54uA
0.60uA
-4.20
0.55uA
0.54uA
0.60uA
-4.10
0.54uA
0.53uA
0.59uA
-4.00
0.54uA
0.52uA
0.58uA
Freescale Semiconductor
PRELIMINARY
121
Appendix B IBIS Model
-3.90
0.53uA
0.52uA
0.58uA
-3.80
0.52uA
0.51uA
0.57uA
-3.70
0.52uA
0.50uA
0.56uA
-3.60
0.51uA
0.50uA
0.56uA
-3.50
0.50uA
0.49uA
0.55uA
-3.40
0.50uA
0.48uA
0.54uA
-3.30
0.49uA
0.48uA
0.53uA
-3.20
0.48uA
0.47uA
0.53uA
-3.10
0.48uA
0.46uA
0.52uA
-3.00
0.47uA
0.46uA
0.51uA
-2.90
0.46uA
0.45uA
0.51uA
-2.80
0.46uA
0.44uA
0.50uA
-2.70
0.45uA
0.44uA
0.49uA
-2.60
0.44uA
0.43uA
0.49uA
-2.50
0.44uA
0.42uA
0.48uA
-2.40
0.43uA
0.41uA
0.47uA
-2.30
0.42uA
0.41uA
0.46uA
-2.20
0.42uA
0.40uA
0.46uA
-2.10
0.41uA
0.39uA
0.45uA
-2.00
0.40uA
0.39uA
0.44uA
-1.90
0.39uA
0.38uA
0.44uA
-1.80
0.39uA
0.37uA
0.43uA
-1.70
0.38uA
0.37uA
0.42uA
-1.60
0.37uA
0.36uA
0.42uA
-1.50
0.37uA
0.35uA
0.41uA
-1.40
0.36uA
0.35uA
0.40uA
-1.30
0.35uA
0.34uA
0.39uA
-1.20
0.35uA
0.33uA
0.39uA
-1.10
0.34uA
0.33uA
0.38uA
-1.00
0.33uA
0.32uA
0.37uA
-0.90
0.33uA
0.31uA
0.37uA
-0.80
0.32uA
0.31uA
0.36uA
-0.70
0.31uA
0.30uA
0.35uA
-0.60
0.31uA
0.29uA
0.35uA
-0.50
0.30uA
0.29uA
0.34uA
-0.40
0.29uA
0.28uA
0.33uA
-0.30
0.29uA
0.27uA
0.32uA
-0.20
0.28uA
0.27uA
0.32uA
-0.10
0.27uA
0.26uA
0.31uA
0.00
0.27uA
0.25uA
0.30uA
|
| End [Model] pdudgz
|
|************************************************************************
122
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
|
Model pdidgz
|************************************************************************
|
[Model]
pdidgz
Model_type
Input
Polarity
Non-Inverting
Vinl =
0.000V
Vinh =
3.30V
C_comp
5.00pF
5.00pF
5.00pF
|
|
[Temperature Range]
25.00
0.12k
0.000
[Pullup Reference]
3.30V
3.00V
3.60V
[Pulldown Reference]
0.000V
0.000V
0.000V
[POWER Clamp Reference]
5.00V
4.50V
5.50V
[GND Clamp Reference]
0.000V
0.000V
0.000V
[GND_clamp]
| voltage
I(typ)
I(min)
I(max)
|
-5.00
-64.63A
-59.13A
-66.41A
-4.80
-61.55A
-56.41A
-63.21A
-4.60
-58.47A
-53.69A
-60.01A
-4.40
-55.39A
-50.97A
-56.81A
-4.20
-52.31A
-48.25A
-53.61A
-4.00
-49.23A
-45.53A
-50.41A
-3.80
-46.15A
-42.81A
-47.21A
-3.60
-43.07A
-40.09A
-44.01A
-3.40
-39.99A
-37.37A
-40.81A
-3.20
-36.91A
-34.65A
-37.61A
-3.00
-33.82A
-31.94A
-34.41A
-2.80
-30.73A
-29.22A
-31.22A
-2.60
-27.64A
-26.51A
-28.02A
-2.40
-24.56A
-23.79A
-24.82A
-2.20
-21.47A
-21.08A
-21.62A
-2.00
-18.38A
-18.36A
-18.42A
-1.80
-15.29A
-15.64A
-15.22A
-1.60
-12.20A
-12.93A
-12.03A
-1.40
-9.12A
-10.21A
-8.83A
-1.20
-6.03A
-7.50A
-5.63A
-1.00
-2.94A
-4.78A
-2.43A
-0.80
-0.20A
-2.07A
-64.14mA
-0.60
-1.79mA
-96.39mA
-4.77mA
-0.40
-22.83uA
-0.47mA
-0.14mA
-0.20
-0.15uA
-1.56uA
-0.37uA
Freescale Semiconductor
PRELIMINARY
123
Appendix B IBIS Model
-0.00
-88.71nA
-89.34nA
-0.11uA
0.20
-72.38nA
-68.50nA
-88.30nA
0.40
-56.11nA
-52.12nA
-71.55nA
0.60
-39.84nA
-35.76nA
-54.82nA
0.80
-23.57nA
-19.40nA
-38.12nA
1.00
-7.31nA
-3.04nA
-21.42nA
1.20
8.94nA
13.32nA
-4.73nA
1.40
25.19nA
29.68nA
11.97nA
1.60
41.42nA
46.03nA
28.68nA
1.80
57.64nA
62.39nA
45.42nA
2.00
73.83nA
78.74nA
62.20nA
2.20
89.95nA
94.86nA
79.06nA
2.40
0.11uA
0.11uA
96.02nA
2.60
0.12uA
0.12uA
0.11uA
2.80
0.13uA
0.13uA
0.13uA
3.00
0.14uA
0.14uA
0.14uA
3.20
0.15uA
0.21uA
0.15uA
3.40
0.15uA
0.15uA
0.16uA
3.60
0.16uA
0.10uA
0.17uA
3.80
0.17uA
47.20nA
0.18uA
4.00
0.18uA
-5.80nA
0.18uA
4.20
0.19uA
-58.80nA
0.19uA
4.40
0.20uA
-0.11uA
0.20uA
4.60
0.20uA
-0.16uA
0.21uA
4.80
0.21uA
-0.22uA
0.22uA
5.00
0.22uA
-0.27uA
0.23uA
|
[POWER_clamp]
| voltage
I(typ)
I(min)
I(max)
|
-5.00
0.60uA
0.59uA
0.65uA
-4.90
0.60uA
0.58uA
0.64uA
-4.80
0.59uA
0.58uA
0.64uA
-4.70
0.58uA
0.57uA
0.63uA
-4.60
0.58uA
0.56uA
0.62uA
-4.50
0.57uA
0.56uA
0.62uA
-4.40
0.56uA
0.55uA
0.61uA
-4.30
0.56uA
0.54uA
0.60uA
-4.20
0.55uA
0.54uA
0.59uA
-4.10
0.54uA
0.53uA
0.59uA
-4.00
0.54uA
0.52uA
0.58uA
-3.90
0.53uA
0.52uA
0.57uA
-3.80
0.52uA
0.51uA
0.57uA
-3.70
0.52uA
0.50uA
0.56uA
124
PRELIMINARY
Freescale Semiconductor
Appendix B IBIS Model
-3.60
0.51uA
0.50uA
0.55uA
-3.50
0.50uA
0.49uA
0.55uA
-3.40
0.49uA
0.48uA
0.54uA
-3.30
0.49uA
0.48uA
0.53uA
-3.20
0.48uA
0.47uA
0.53uA
-3.10
0.47uA
0.46uA
0.52uA
-3.00
0.47uA
0.46uA
0.51uA
-2.90
0.46uA
0.45uA
0.51uA
-2.80
0.45uA
0.44uA
0.50uA
-2.70
0.45uA
0.43uA
0.49uA
-2.60
0.44uA
0.43uA
0.48uA
-2.50
0.43uA
0.42uA
0.48uA
-2.40
0.43uA
0.41uA
0.47uA
-2.30
0.42uA
0.41uA
0.46uA
-2.20
0.41uA
0.40uA
0.46uA
-2.10
0.41uA
0.39uA
0.45uA
-2.00
0.40uA
0.39uA
0.44uA
-1.90
0.39uA
0.38uA
0.44uA
-1.80
0.39uA
0.37uA
0.43uA
-1.70
0.38uA
0.37uA
0.42uA
-1.60
0.37uA
0.36uA
0.42uA
-1.50
0.37uA
0.35uA
0.41uA
-1.40
0.36uA
0.35uA
0.40uA
-1.30
0.35uA
0.34uA
0.39uA
-1.20
0.35uA
0.33uA
0.39uA
-1.10
0.34uA
0.33uA
0.38uA
-1.00
0.33uA
0.32uA
0.37uA
-0.90
0.33uA
0.31uA
0.37uA
-0.80
0.32uA
0.31uA
0.36uA
-0.70
0.31uA
0.30uA
0.35uA
-0.60
0.31uA
0.29uA
0.35uA
-0.50
0.30uA
0.29uA
0.34uA
-0.40
0.29uA
0.28uA
0.33uA
-0.30
0.29uA
0.27uA
0.33uA
-0.20
0.28uA
0.27uA
0.32uA
-0.10
0.28uA
0.26uA
0.31uA
0.00
0.27uA
0.26uA
0.31uA
|
| End [Model] pdidgz
Freescale Semiconductor
PRELIMINARY
125
Appendix B IBIS Model
Revision History
126
Revision
Date
0.0
27 April 2004
Description
Initial release
PRELIMINARY
Freescale Semiconductor
NOTES
How to Reach Us:
Home Page:
www.freescale.com
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
1-800-521-6274 or 480-768-2130
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku
Tokyo 153-0063
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
852-26668334
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconductor products. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Freescale Semiconductor reserves the right to make changes without further
notice to any products herein. Freescale Semiconductor makes no warranty,
representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Freescale Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters that may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer
application by customer’s technical experts. Freescale Semiconductor does
not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized
for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other
application in which the failure of the Freescale Semiconductor product could
create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of
Freescale Semiconductor, Inc. All other product or service names
are the property of their respective owners.
© Freescale Semiconductor, Inc. 2004. All rights reserved.
DSP56374
Rev. 1
11/2004