Ordering number : ENN6512 DSP10 Silicon Diffused Junction Type DSP10 Power Rectifier Features • Facilitates automatic mounting and miniaturization in end products. Peak reverse voltage : VRM=600V. Average rectified current : IO=1.0A. unit : mm 1300 [DSP10] 2.8 1.0 • Package Dimensions 1.8 • Cathode mark 1.4 3.9 1.0 1.0 0.5 1.0 1.8 Specifications SANYO : SHP Absolute Maximum Ratings at Ta=25°C Parameter Peak Reverse Voltage Average Rectified Current Symbol VRM IO Surge Forward Current IFSM Junction Temperature Storage Temperature Tj Tstg Conditions Ratings 600 1.0 Unit V A 0.64 A 0.80 A 25 A 150 --55 to +150 °C °C 50Hz sine wave, mounted on an alumina board Load resistor (solder pad size 4mm2✕20µmt) Mounted PCB Load resistor (solder pad size 4mm2✕20µmt) Mounted PCB Load resistor (solder pad size 4mm2✕20µmt) 50Hz sine wave non-repetitive, 1cycle peak value Electrical Characteristics at Ta=25°C Parameter Forward Voltage Reverse Current Thremal Resistance Symbol VF IR θi-l θi-a Conditions IF=1.0A VR=VRM Junction-Lead Junction-Ambient, mounted on an alumina board (solder pad size 4mm2✕20µmt) Mounted on PCB (solder pad size 4mm2✕35µmt) Mounted on PCB (solder pad size 16mm2✕35µmt) min typ max 1.1 10 20 108 Unit V µA °C/W °C/W 186 °C/W 142 °C/W Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 40700 GI IM No.6512-1/2 DSP10 IF -- VF 10 IO -- Ta 1.2 Sine wave Load resistor Average Rectified Current, IO -- A 7 3 50° C 2 1.0 7 25°C Ta= 1 Forward Current, IF -- A 5 5 3 2 0.1 When mounted on an alumina board. Solder pad size 2mm PCB board 1 Solder pad size 4mm PCB board 2 Solder pad size 2mm Al um in ab PC 0.8 B PC oa bo Bb ard oar 0.6 rd 1 d2 0.4 0.2 0 0.4 0.6 0.8 1.0 1.2 1.4 1.6 Forward Voltage, VF -- V 1.8 IT02088 0 20 40 60 80 100 120 140 Ambient Temperature, Ta -- °C 160 IT02089 IFSM -- n 50 Surge Foward Current, IFSM -- A 1.0 40 30 20 50Hz 10 0 1.0 2 3 5 7 10 2 3 Number of Cycles at 50Hz, n 5 7 100 IT02090 Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of April, 2000. Specifications and information herein are subject to change without notice. PS No.6512-2/2